Machine Translated by Google

FX2N PLC manual

Safety Precautions
1. Please confirm the power supply voltage before installing and using the controller. Please refer to the standard voltage of the controller. 2. Please do not touch

the controller PCB board when it is powered on, and do not connect external input and output when it is powered on.

terminal

3. Please refer to the instructions in this manual for instructions and soft components. If used incorrectly, the PLC may automatically stop running, causing a

safety accident. The ERR light of the controller will light up and all outputs will be disabled. If this happens, please refer to the error code. Check the

relevant error content and error step number through the toolbar "DiagnosisÿPLC Diagnosis"

4. The watchdog WTD may also cause the PLC to actively stop running, causing a safety accident. When the controller stops due to WTD, the ERR light will light

up and all outputs will be disabled. If WTD overflows, please adjust the program structure, especially when using FOR CJ CALL. It is easy to cause the

controller scan time to be too long. The initial scan time is 200ms. The D8000 value can be changed to meet the requirements. The modification

range is 10-1000ms, or it can be changed directly through WDT.

5. If there is interference in the input, you can change the input filter value of D8020 to avoid interference.

main feature

[Integrated programmable controller] Power

supply, CPU, memory, input and output form a unit of programmable controller, which can be conveniently used in automated logic control [Input and output

use] Please refer to the controller model

for specific points. The inputs and

outputs used can be used as internal devices and touch screen control addresses to use [Run/Stop] . By default, the controller will run after powering off and

then on again. Even if the PLC is forced to stop

before powering off, you

can use GX or GX

Works 2 for remote operation, or switch for trigger operation [built-in two sets of analog inputs]

The two analog inputs end at D8030 D8031

0-10V. The corresponding input value is 0-4095, please do not exceed

Use 10V, exceeding the range may permanently damage the controller.

[PWM output] One channel

of built-in PWM pulse width modulation output. Because the optical coupler has a delay, this channel does not pass through the optical coupler. The frequency is

1KHZ, the duty cycle corresponds to the D8033 duty cycle range 0-1000. After RC filtering, it can be used as an analog quantity [positioning output Y0 Y1]. The

two

outputs Y0 Y1 can use the PLSY

PLSR PWM instruction at the same time for related control [program capacity] Maximum program capacity is 4K steps
Machine Translated by Google

Introduction to use

1. Power supply specifications and

external wiring a)

Power supply

specifications b) Power supply

connection example

2. Input specifications and external

wiring a) Input specifications b) Use of

DC input signal c) Use of built-in high-

speed counter 3.

Output specifications and external wiring

a) Output specifications b) Use of relay

output circuit c) Use of transistor output circuit 4.

Program encryption

and decryption

methods a) Normal encryption b)

Super encryption c) Decryption password and ladder

diagram 5. Pulse output instructions and high-

speed input
applications a ) Pulse output PLSY PLSR PWM b) High-speed input

6. Pulse width PWM modulation output and

AD0 AD1 input use 7. Device

number, error

code table 8. Special register meaning 9. Instruction table 10. Special function description, and precautions
Machine Translated by Google

Power supply specifications and external wiring

If it is a low-power controller, it is generally powered by 24V. The transistor voltage range is between 12V and 24V. The relay voltage

range is between 16V and 24V. The maximum power supply voltage is 28V. Higher than this voltage may permanently damage the

controller.

Input specifications and external wiring

The input needs to ensure that the X point has a current of 2.5ma or more for ON, and 1ma or less for OFF.

Output specifications and external wiring

The output is transistor and relay output. The output DC current of the transistor cannot exceed DC5-30V 3A, and the maximum

current of the relay AC 250V is 5A.

Machine Translated by Google

Program encryption and password removal methods

Encryption: OnlineÿLogin keywordÿNew login, change, if it is set to 88888888, the password cannot be changed anymore Cancel

password:

OnlineÿLogin keywordÿCancel, if it is set to 88888888, the password cannot be canceled Super encryption: OnlineÿLogin

KeywordsÿNew login, change, set to 88888888, can no longer be read out

PLC program, and can no longer cancel or change the password. You can only download the program to the controller. If you want to

cancel the password, you can operate it through <Clear PLC

Memory>. Memory clearing and password: If the password is forgotten or super-encrypted, it needs to be restored. To reach the

normal state, you can go onlineÿClear PLC MemoryÿPLC MemoryÿExecute . Note: This operation will cause the ladder diagram

program to be completely deleted.

Machine Translated by Google

Pulse output instructions and high-speed input applications

For high-speed output PLSY PLSR PWM applications,

two identical instructions cannot be scanned in one scan cycle and point to the same channel. If such a situation occurs, please use a

jump instruction to jump away, otherwise the controller will output abnormal pulses. PLSY DPLSY is considered the same Instructions PLSR

DPLSR are the same instructions. The PLC pulse output range is 5HZ-3KHZ. Please limit the pulse to 3KHZ.

The input used for high-speed counter

input is between the performance speed of the optical coupling itself. The maximum high-speed counter does not exceed 2KHZ. If it exceeds 2KHZ,

erroneous counting may occur.

C235 (32-bit high-speed addition and subtraction counter that holds power outage, X0, X1 AB phase counting,

M8235 indicates direction AB (bidirectional counting)

C236 (32-bit high-speed addition and subtraction counter X0->+ X1->- X0 plus

Count X1, count down, M8236 indicates direction)

C237 (32-bit high-speed power failure latching counter X0->+ single-phase counting only increases but does not decrease)

C238 (32-bit high-speed power failure latched counter X1->+ single-phase counting only increases but does not decrease)
Machine Translated by Google
Machine Translated by Google

Pulse width PWM modulation output and AD0 AD1 input use

Use pulse modulation to output a

pulse width carrier of 1KHZ, with a width range of 0-1000. Use address D8033, and the output impedance is 330ÿ. The pulse obtained without passing

through the optical coupling prevents pulse inaccuracy caused by optical coupling delay.

AD0 AD1 input voltage

range DC 0-10V. Exceeding it may permanently damage the controller. The corresponding address is D8030 D8031, the resolution is 12bit, and the

corresponding value is 0-4096.

Machine Translated by Google

Device number, error code table

project performance

General use M0-M511

Auxiliary relay for holding. M512-M3071

Special use. M8000-M8255

General use. S0-S127

state
For holding. S128-S999

100ms T0-T99 0.1-3276.7 seconds

10ms T200-T244 0.01-327.67 seconds

timer
1ms cumulative type T245-T248 0.001-32.767 seconds

10ms cumulative type T250-T254 0.1-3276.7 seconds

16-bit incremental C0-C15 0-32767

mode 16-bit hold mode C16-C99 0-32767

counter
32-bit bidirectional hold C200-C234 -2147483648-+214848347

32-bit special counter C235-C247 -2147483648-+214848347

16 bits for general D0-D511

use, 16 bits for holding, D512-D998

data register
16 bits for special use, D8000-D8255

16 bits for indexing Z0 , V0

Pointer CJ CALL branch P0-P127

nesting Decimal N0-N7

number K for main -32767-+32768

Constant 16 bits
control 16-hour 0-FFFF

number H Decimal -2147483648-+214848347

Constant 32 bits
number K 16-hour number H 0-FFFFFFFF
Machine Translated by Google

Error code meaning

Number value meaning Number value meaning

D8063 D8066 6603
D8063 D8066 6604
D8063 D8066 6605

D8063 6306 WDT overflow, monitor overflow D8066 6607

D8063 D8066 6608
D8063 D8066 6631

The meaning of the number value The meaning of the number value

D8065 6501 Device combination error D8067 6701 CALL exception

D8065 D8067 6702 CALL level 7 or above
D8065 D8067

D8065 6505 Out of software number range D8067

D8065 D8067
D8065 D8068 Error step number
Machine Translated by Google

special register

Unspecified special registers can be used as ordinary registers

D8000 scan cycle monitoring ms M8000 RUN ON

D8001 PLC type version M8001 RUN OFF

D8002 M8002 initial pulse ON

D8003 M8003 initial pulse OFF

D8004 Error special M number M8060-M8067 M8004 Error occurred M8060-M6067

D8005 M8005

D8006 M8006

D8007 M8007

D8008 M8008

D8009 M8009

D8010 Current value of scan time (unit 0.1ms) M8010

D8011 Minimum scan time (unit 0.1ms) M8011 10MS clock

D8012 Maximum scan time (unit 0.1ms) M8012 100MS clock

D8013 M8013 1S clock
D8014 M8014 1 minute clock
D8015 M8015

D8016 M8016

D8017 M8017

D8018 M8018

D8019 M8019

D8020 input X filtering maximum 100ms M8020

D8021 M8021

D8022 M8022 carry flag

D8023 M8023

D8024 M8024

D8025 M8025

D8026 M8026

D8027 M8027

D8028 Contents of index register Z M8028

D8029 Contents of index register V M8029 instruction execution end Y0 pulse

D8030 Analog channel 0 input 0-4091 M8030 Instruction execution end Y1 pulse

D8031 Analog channel 1 input 0-4091 M8031

D8032 Main power supply voltage value AD value M8032

PWM duty cycle channel 0 output 1KHZ

D8033 0-1000 M8033

D8034 M8034

D8035 M8035

D8036 M8036

D8037 M8037

D8038 M8038
Machine Translated by Google

D8039 M8039
D8040 M8040 transfer prohibited
D8041 M8041
D8042 M8042
D8043 M8043
D8044 M8044
D8045 M8045
D8046 M8046
D8047 M8047 Y0 pulse output
D8048 M8048 Y1 pulse output
D8049 M8049
D8050 M8050
D8051 M8051
D8052 M8052
D8053 M8053
D8054 M8054

D8055 M8055
D8056 M8056
D8057 M8057
D8058 M8058
D8059 M8059
D8060 M8060
D8061 M8061
D8062 M8062

D8063 Parallel link error number M8063 Parallel link error

D8064 Parameter error number M8064 Parameter error
D8065 syntax error number M8065 Syntax error
D8066 Loop error number M8066 Loop error

D8067 Operation error number M8067 Operation error

D8068 The step number where the operation error occurred M8068 Operation error latch
D8069 M8069
D8070 M8070
D8071 M8071
D8072 M8072

D8073 M8073
D8074 M8074
D8075 M8075
D8076 M8076
D8077 M8077
D8078 M8078
D8079 M8079

D8080 M8080
D8081 M8081
Machine Translated by Google

D8082 M8082
D8083 M8083
D8084 M8084
D8085 M8085
D8086 M8086
D8087 M8087
D8088 M8088
D8089 M8089
D8090 M8090
D8091 M8091

D8092 M8092
D8093 M8093
D8094 M8094
D8095 M8095
D8096 M8096
D8097 M8097

D8098 M8098
D8099 M8099
D8100 M8100
D8101 M8101
D8102 M8102
D8103 M8103
D8104 M8104
D8105 M8105
D8106 M8106
D8107 M8107
D8108 M8108
D8109 M8109

D8110 M8110
D8111 M8111
D8112 M8112
D8113 M8113
D8114 M8114
D8115 M8115

D8116 M8116
D8117 M8117
D8118 M8118
D8119 M8119
D8120 M8120
D8121 M8121
D8122 M8122

D8123 M8123
D8124 M8124
Machine Translated by Google

D8125 M8125

D8126 M8126

D8127 M8127

D8128 M8128

D8129 M8129

D8130 M8130

D8131 M8131

D8132 M8132

D8133 M8133

D8134 M8134

D8135 M8135

D8136 M8136

D8137 M8137

D8138 M8138

D8139 M8139

D8140 Y0 total number of pulses low M8140

D8141 Y0 High bit of the total number of pulses M8141

D8142 Y1 pulse total number low bit M8142

D8143 Y1 pulse total number high bit M8143

D8144 M8144

D8145 M8145

D8146 M8146

D8147 M8147

D8148 M8148

D8149 M8149

D8150 M8150

D8151 M8151

D8152 M8152

D8153 M8153

D8154 M8154

D8155 M8155

D8156 M8156

D8157 M8157

D8158 M8158

D8159 M8159

D8160 M8160

D8161 M8161

D8162 M8162

D8163 M8163

D8164 M8164

D8165 M8165

D8166 M8166

D8167 M8167
Machine Translated by Google

D8168 M8168
D8169 M8169
D8170 M8170
D8171 M8171
D8172 M8172
D8173 M8173
D8174 M8174
D8175 M8175
D8176 M8176
D8177 M8177
D8178 M8178
D8179 M8179
D8180 M8180
D8181 M8181

D8182 Z1 register content M8182

D8183 V1 register content M8183

D8184 Z2 register content M8184

D8185 V2 register content M8185

D8186 Z3 register content M8186

D8187 V3 register content M8187

D8188 Z4 register content M8188

D8189 V4 register content M8189

D8190 Z5 register content M8190

D8191 V5 register content M8191

D8192 Z6 register content M8192

D8193 V6 register content M8193

D8194 Z7 register content M8194

D8195 V7 register content M8195

D8196 M8196
D8197 M8197
D8198 M8198
D8199 M8199
D8200 M8200 C200 counter direction
D8201 M8201 C201 counter direction
D8202 M8202 C202 counter direction
D8203 M8203 C203 counter direction
D8204 M8204 C204 counter direction
D8205 M8205 C205 counter direction
D8206 M8206 C206 counter direction
D8207 M8207 C207 counter direction
D8208 M8208 C208 counter direction
D8209 M8209 C209 counter direction
D8210 M8210 C210 counter direction
Machine Translated by Google

D8211 M8211 C211 counter direction

D8212 M8212 C212 counter direction
D8213 M8213 C213 counter direction
D8214 M8214 C214 counter direction
D8215 M8215 C215 counter direction
D8216 M8216 C216 counter direction
D8217 M8217 C217 counter direction
D8218 M8218 C218 counter direction
D8219 M8219 C219 counter direction
D8220 M8220 C220 counter direction
D8221 M8221 C221 counter direction
D8222 M8222 C222 counter direction
D8223 M8223 C223 counter direction
D8224 M8224 C224 counter direction
D8225 M8225 C225 counter direction
D8226 M8226 C226 counter direction
D8227 M8227 C227 counter direction
D8228 M8228 C228 counter direction
D8229 M8229 C229 counter direction
D8230 M8230 C230 counter direction
D8231 M8231 C231 counter direction
D8232 M8232 C232 counter direction
D8233 M8233 C233 counter direction
D8234 M8234 C234 counter direction
D8235 M8235 C235 counter direction
D8236 M8236 C236 counter direction
D8237 M8237 C237 counter direction
D8238 M8238
D8239 M8239
D8240 M8240
D8241 M8241
D8242 M8242
D8243 M8243
D8244 M8244
D8245 M8245
D8246 M8246
D8247 M8247
D8248 M8248
D8249 M8249
D8250 M8250
D8251 M8251
D8252 M8252
D8253 M8253
Machine Translated by Google

D8254 M8254
D8255 M8255

This product currently supports the following commands of Fx2N

Basic instructions:

LD,LDI,AND,ANI,OR,ORI,INV,OUT,

(OUTT,OUTC),SET,RST,ANB,ORB,LDP,LDF,ANDP,ANDF, (OUTT,OUTC),SET,RST,ANB,

ORB,LDP,LDF,ANDP,ANDF, ORP,ORF,PLS,PLF,MPS,MRD,MPP,RET,NOP,END. Step

instruction: STL: supports up to 8 parallel branches, different status numbers can have
double Coil.Contact comparison command:

LD>=,LD<=,LD>,LD<,LD<>,LD=,AND>=,AND<=,AND>,AND<, AND<>,AND=,OR>=,OR<=,OR>,OR<,OR<>,OR=. ÿÿÿÿÿ

ÿÿÿ

MOV, CML, CMP, ZCP, FMOV. Four arithmetic

operations instructions:

ADD,SUB,MUL,DIV,INC,DEC,WAND,WOR,WXOR,NEG.
Floating point operation instructions:

ADD,SUB,MUL,DIV,FLT,DFLT,INT,DINT,DESQR,EDCMP.
Trigonometric function operation instructions:

SIN,COS,TAN,SQR,DSQR. Rotation shift

instructions:

ROR, ROL, RCR, RCL. Data

processing instructions:

ZRST.

Program instructions:

CJ (maximum 128 addresses), CALL (maximum 8 levels of nesting, 128 subroutines

sequence), SRET, FEND, WDT, FOR (maximum 7 levels of nesting), NEXT.

Convenient instructions:

ALT. High-

speed processing instructions:

REF, REFF, PWM (support Y0, Y1 each, can be used at the same time), PLSY (support Y0, Y1 each

One channel), PLSR (supports Y0, Y1 each channel) pulse frequency 5HZ-20KHZ

This product supports 32-bit instructions in Fx2N functional instructions, including D instructions and P instructions, that is, it supports function instructions.

Add D before the command or P after it, such as DMOV or MOVP, etc.
Machine Translated by Google

Special function descriptions and precautions

1: The controller does not accept online writing commands, which means that the Shift+F4 writing program is invalid and you need to press

F4 is converted and then written into the PLC controller

2: If there are illegal instructions that cause uncontrollable exceptions, the controller will automatically delete the user program to restore

normal use. Generally, this will not happen. Usually writing illegal instructions will cause the system to Use the "DiagnosisÿPLC Diagnosis"

column to view the abnormal content and the abnormal step number.

3: The index instruction can only

use D for indexing. TCXYSM is not supported. If used, an operation error will occur. 4: When using the PWM instruction for pulse

output, D1 is the output frequency and D2 is the duty cycle of 100%. =1000; Example PWM K500 K200 Y0 Target Y0 outputs duty

cycle 20%=200/1000 at 500HZ Example PWM K5000 K789 Y1 Target Y1 outputs duty cycle 78.9%=789/1000 at

500HZ 5: When downloading the program, please be careful to select less than or equal to 4K capacity,