3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

https://www.examtopics.com/exams/cisco/300-410/view/4/ 1/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #551 Topic 1

Refer to the exhibit. In Cisco DNA Center, a network engineer identifies that BGP-learned networks are repeatedly withdrawn from peers. Which

configuration must the engineer apply to resolve the issue?

A. router bgp 100

bgp dampening Most Voted

B. router bgp 100

bgp graceful-restart

C. route-map Dampening permit 10

set dampening 15 750 2000 60

router bgp 100

neighbor 10.140.212.5 route-map Dampening out

D. route-map Dampening permit 10

set dampening 15 750 2000 60

router bgp 100

neighbor 10.140.212.5 route-map Dampening in

Correct Answer: A

https://www.examtopics.com/exams/cisco/300-410/view/4/ 2/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Community vote distribution

A (73%) D (27%)

Question #552 Topic 1

Refer to the exhibit. Which configuration allows the operation level 1 team of 10 engineers to log in at least three at a time to router R3 using

network credentials over HTTP?

A. R3(config)#ip http authentication enable

R3(config)#no access-list 20 permit 172.16.10.48 0.0.0.15

R3(config)#access-list 20 permit 172.16.10.48 0.0.0.7

B. R3(config)#ip http max-connections 3

R3(config)#ip http accounting commands 3 default

C. R3(config)#ip http authentication aaa

R3(config)#ip http max-connections 3 Most Voted

D. R3(config)#ip http authentication aaa

R3(config)#no access-list 20 permit 172.16.10.48 0.0.0.15

R3(config)#access-list 20 permit 172.16.10.48 0.0.0.7

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 3/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #553 Topic 1

Which router takes an active role between two LDP neighbors when initiating LDP session negotiation and LDP TCP connection establishment?

A. with one interface in the MPLS backbone

B. with the higher IP address Most Voted

C. with the lowest IP address

D. with the larger number of LDP TCP neighbors

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 4/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #554 Topic 1

Refer to the exhibit. An enterprise operations team must monitor all application server traffic in the data center. The team finds that traffic coming

from the hub site from R3 and R6 is monitored successfully, but traffic destined to the application server is not monitored. Which action resolves

the issue?

A. R4(config)#int gigabitEthernet 1/0

R4(config-if)#ip flow ingress

B. R3(config)#int gigabitEthernet 0/0

R3(config-if)#ip flow egress

C. R4(config)#int gigabitEthernet 2/0

R4(config-if)#ip flow egress Most Voted

D. R1(config)#int gigabitEthernet 0/0

R1(config-if)#ip flow egress

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 5/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #555 Topic 1

Which router attaches the VPN label to incoming packets from CE routing?

A. P router

B. PE router Most Voted

C. CE router

D. core router

Correct Answer: B

Community vote distribution

B (100%)

Question #556 Topic 1

Refer to the exhibit. Which action adds the 10.1.7.6/32 route to the BGP table?

A. Add a static route for the 10.1.7.6/32 network.

B. Add summary-address 10.1.7.6 255.255.255.0.

C. Add the network 10.1.7.6 mask 255.255.255.255 backdoor command.

D. Add the network 10.1.7.6 mask 255.255.255.255 command. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 6/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #557 Topic 1

A network engineer must configure an EIGRP stub router at a site that advertises only connected and summary routes. Which configuration

performs this task?

A. router eigrp 100

eigrp stub redistribute

B. router eigrp 100

eigrp stub Most Voted

C. router eigrp 100

eigrp stub connected

D. router eigrp 100

eigrp stub summary

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 7/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #558 Topic 1

Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any

IPv6 routes; however, the IPv4 neighbor relationship is working fine.

Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

A. ipv6 unicast-routing

ipv6 cef

interface Loopback100

ipv6 address 2001:DB8:128::2/128

interface GigabitEthernet1/0

ipv6 address 2001:DB8:1::2/64

router bgp 65002

no bgp default ipv4-unicast

neighbor 2001:DB8:1::1 remote-as 65001

address-family ipv4

network 2001:DB8:128::2/128

B. ipv6 unicast-routing

ipv6 cef

interface Loopback100

ipv6 address 2001:DB8:128::2/128

interface GigabitEthernet1/0

ipv6 address 2001:DB8:1::2/64

router bgp 65002

no bgp default ipv4-unicast

neighbor 2001:DB8:1::1 remote-as 65001

address-family ipv6

network 2001:DB8:128::2/128

C. ipv6 unicast-routing

ipv6 cef

interface Loopback100

ipv6 address 2001:DB8:128::2/128

interface GigabitEthernet1/0

ipv6 address 2001:DB8:1::2/64

description AS65001 ID B468^AD03G907::1

https://www.examtopics.com/exams/cisco/300-410/view/4/ 8/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

router bgp 65002

no bgp default ipv4-unicast

neighbor 2001:DB8:1::1 remote-as 65001

address-family ipv6

network 2001:DB8:128::2/128

neighbor 2001:DB8:1::1 activate Most Voted

D. ipv6 cef

interface Loopback100

ipv6 address 2001:DB8:128::2/128

interface GigabitEthernet1/0

ipv6 address 2001:DB8:1::2/64

router bgp 65002

no bgp default ipv4-unicast

neighbor 2001:DB8:1::1 remote-as 65001

address-family ipv6

network 2001:DB8:128::2/128

neighbor 2001:DB8:1::1 activate

Correct Answer: C

Community vote distribution

C (100%)

Question #559 Topic 1

Refer to the exhibit. Which configuration command establishes an EIGRP neighbor adjacency between the hub and spoke?

A. network 10.1.2.192 command on spoke router

B. network 10.1.2.192 command on hub router Most Voted

C. eigrp-peer 10.1.2.192 command on hub router

D. connected 10.1.2.192 command on spoke router

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 9/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #560 Topic 1

What is the failure detection time with BFD?

A. 3 seconds

B. less than a second Most Voted

C. 2 seconds

D. 1 second

Correct Answer: B

Community vote distribution

B (100%)

Question #561 Topic 1

Refer to the exhibit. A network administrator is trying to switch to the privileged EXEC level on R1 but failed. Which configuration resolves the

issue?

A. enable password Cisco@123 Most Voted

B. tacacs-server enable-password Cisco@123

C. tacacs server enable-password Cisco@123

D. enable-password Cisco@123

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 10/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #562 Topic 1

Refer to the exhibit. The R1 OSPF neighbor is not receiving type 5 external LSAs for 132.108.2.0/24 and 132.108.3.0/24 networks. Which

configuration command resolves the issue?

A. access-list 1 permit 132.108.0.0 0.0.3.255 Most Voted

B. access-list 1 permit 132.108.0.0 0.0.1.255

C. access-list 1 permit 132.108.4.0 0.0.3.255

D. access-list 1 permit 132.108.2.0 0.0.0.255

Correct Answer: A

Community vote distribution

A (100%)

Question #563 Topic 1

Which two technologies optimize MPLS infrastructure using bandwidth protection services when experiencing slow response? (Choose two.)

A. IP LFA

B. MPLS OAM

C. Fast-Reroute

D. VPLS

E. SD-MPLS

https://www.examtopics.com/exams/cisco/300-410/view/4/ 11/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #564 Topic 1

What is the function of penultimate hop popping?

A. The last P router in the path pops off the transport label before traffic is forwarded toward the PE. Most Voted

B. The VPN label is popped off at the egress LSR, and unlabeled traffic is forwarded toward the CE.

C. The transport label is popped off at the egress LSR, and unlabeled traffic is forwarded toward the CE.

D. The second to last P router in the path pops off the VPN label before traffic is forwarded to the last P router.

Correct Answer: A

Community vote distribution

A (80%) C (20%)

Question #565 Topic 1

Refer to the exhibit. Spoke routers do not learn about each other's routes in the DMVPN Phase2 network. Which action resolves the issue?

A. Disable EIGRP split horizon on the Tunnel0 interface of the hub router. Most Voted

B. Rectify incorrect wildcard mask configured on the hub router network command.

C. Configure a static route in each spoke to establish a spoke-to-spoke tunnel.

D. Remove default route from spoke routers to establish a spoke-to-spoke tunnel.

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 12/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #566 Topic 1

Refer to the exhibit. The security department recently installed a monitoring device between routers R3 and R5, which caused a loss of network

connectivity for users connected to R5. Troubleshooting revealed that the monitoring device cannot forward multicast packets. The team already

updated R5 with the correct configuration. Which configuration must be implemented on R3 to resolve the problem by ensuring R3 as the DR for

the R3-R5 segment?

A. interface FastEthernet0/0

ip address 10.99.53.1 255.255.255.252

ip access-group 122 in

ip ospf network non-broadcast

ip ospf priority 100

router ospf 10

router-id 10.10.3.255

network 10.99.53.0 0.0.0.3 area 0

neighbor 10.99.53.2

access-list 122 permit 89 host 10.99.53.2 host 10.99.53.1

access-list 122 deny 89 any any

access-list 122 permit tcp any any

access-list 122 permit udp any any

access-list 122 permit icmp any any Most Voted

B. interface FastEthernet0/0

ip address 10.99.53.1 255.255.255.252

ip access-group 122 in

ip ospf network non-broadcast

ip ospf priority 0

router ospf 10

router-id 10.10.3.255

neighbor 10.99.53.2

access-list 122 permit 88 host 10.99.53.2 host 10.99.53.1

access-list 122 deny 88 any any

access-list 122 permit tcp any any

access-list 122 permit udp any any

access-list 122 permit icmp any any

C. interface FastEthernet0/0

ip address 10.99.53.1 255.255.255.252

ip access-group 122 in

ip ospf network non-broadcast

ip ospf priority 0

router ospf 10

https://www.examtopics.com/exams/cisco/300-410/view/4/ 13/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

router-id 10.10.3.255

network 10.99.53.0 0.0.0.3 area 0

neighbor 10.99.53.2

access-list 122 permit 89 host 10.99.53.2 host 10.99.53.1

access-list 122 deny 89 any any

access-list 122 permit tcp any any

access-list 122 permit udp any any

access-list 122 permit icmp any any

D. interface FastEthernet0/0

ip address 10.99.53.1 255.255.255.252

ip access-group 122 in

ip ospf network point-to-point

ip ospf priority 0

router ospf 10

router-id 10.10.3.255

network 10.99.53.0 0.0.0.3 area 0

neighbor 10.99.53.2

access-list 122 permit 88 host 10.99.53.2 host 10.99.53.1

access-list 122 deny 88 any any

access-list 122 permit tcp any any

access-list 122 permit udp any any

access-list 122 permit icmp any any

Correct Answer: A

Community vote distribution

A (100%)

Question #567 Topic 1

What is a characteristic of an MPLS LSP tunnel?

A. bidirectional tunnel

B. secured bidirectional tunnel

C. hop-by-hop tunnel

D. unidirectional tunnel Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 14/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #568 Topic 1

Which two reasons would cause an LSP to break between two PE routers? (Choose two.)

A. lost LDP adjacency Most Voted

B. matching labels

C. prefix mismatch Most Voted

D. IGP hello adjacency

E. MPLS not enabled

Correct Answer: AC

Community vote distribution

AC (70%) AE (30%)

Question #569 Topic 1

Which protocol must be secured with MD-5 authentication across the MPLS cloud to prevent hackers from introducing bogus routers?

A. RSVP

B. LSP

C. LDP Most Voted

D. MP-BGP

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 15/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #570 Topic 1

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

https://www.examtopics.com/exams/cisco/300-410/view/4/ 16/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Troubleshoot and resolve the issues to achieve these goals:

1. Ensure that R1 reaches the prefix 10.6.66.6 without any single point of failure in the path. Do not use a static route or policy-based routing to

accomplish this.

2. Ensure that R1 loopback 1 reaches to R6’s loopback 1 by following the path through R1, R3, R5 to R6 and vice versa. Use metric values K1 =

100000, K2=1, K3=255, K4=10, K5=1500 to modify the default metric in EIGRP if required. Do not use a route-map.

3. Ensure that on R3, prefix 10.0.56.6/32 uses the SP1 to route to the Internet, whereas prefix 172.16.12.2/32 uses the SP2 to route to the Internet.

Do not use BGP to accomplish this. Use the pre-configured route-maps SP1 and SP2 and modify to accomplish the task if required. Use the ping

and trace commands from R6 and R2 to prefixes 209.165.202.132 and 209.165.202.128, respectively to verify the results.

Correct Answer:

https://www.examtopics.com/exams/cisco/300-410/view/4/ 17/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #571 Topic 1

Refer to the exhibit. Which configuration resolves the issue?

A.

B.

Most Voted

C.

D.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 18/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #572 Topic 1

Refer to the exhibit. Which configuration resolves the route filtering issue on R1 to redistribute all the routes except 172.16.2.48/28?

A.

B.

C.

Most Voted

https://www.examtopics.com/exams/cisco/300-410/view/4/ 19/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

D.

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 20/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #573 Topic 1

https://www.examtopics.com/exams/cisco/300-410/view/4/ 21/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Refer to the exhibit. An engineer troubleshoots a connectivity problem that is impacting the communication from the users at segment

172.16.3.16 /28 to the server farm at 192.168.5.16/

28. Which configuration resolves the issue on router R1?

A. router rip

redistribute ospf 1 metric 16

B. router ospf 1

redistribute rip metric 14

C. router rip

redistribute ospf 1 metric 14 Most Voted

D. router ospf 1

redistribute rip metric 16

Correct Answer: C

Community vote distribution

C (70%) A (30%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 22/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #574 Topic 1

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

Troubleshoot R-WEST to achieve the desired results:

1. All the commands should be locally saved to the router as well as sent to the Syslog server except passwords.

2. All the Cisco OSPF LSA traps should be sent to the SNMP server.

https://www.examtopics.com/exams/cisco/300-410/view/4/ 23/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Correct Answer:

https://www.examtopics.com/exams/cisco/300-410/view/4/ 24/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #575 Topic 1

Refer to the exhibit. Router R1 (head office) is not always preferred for all users to access hosting services R1 should be primary, and the DR site

should only be used if router R1 or its uplink fails.

Which configuration resolves the issue?

A.

Most Voted

B.

C.

D.

https://www.examtopics.com/exams/cisco/300-410/view/4/ 25/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Correct Answer: A

Community vote distribution

A (100%)

Question #576 Topic 1

Refer to the exhibit. A network administrator configured NetFlow data but the data is not visible at the NetFlow collector. Which configuration

allows the router to send the records?

A. Configure a different interface to send the records. Most Voted

B. Configure the management interface in the global routing table to send the records.

C. Configure the NetFlow collector to listen at export-protocol netflow-v5.

D. Rectify NetFlow collector reachability from the management interface.

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 26/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #577 Topic 1

Refer to the exhibit. An engineer is troubleshooting a routing loop on the network to reach the 172.16 3.0/16 from the OSPF domain. Which

configuration on router R1 resolves the issue?

A.

https://www.examtopics.com/exams/cisco/300-410/view/4/ 27/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

B.

C.

D. Most Voted

Correct Answer: D

Community vote distribution

D (88%) 12%

Question #578 Topic 1

Which IPv6 security feature blocks all traffic from an IPv6 host when initially connecting to a switch port except for traffic to gain an IPv6 address

and discover IPv6 neighbors?

A. IPv6 Source Guard Most Voted

B. IPv6 DHCP Guard

C. IPv6 Destination Guard

D. IPv6 RA Guard

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 28/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #579 Topic 1

Refer to the exhibit. An IPv6 ACL is applied to restrict PC1 from communicating with PC2 and allow all other traffic. Which configuration resolves

the issue?

A. R3(config-ipv6-acl)#no sequence 20

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B host 2001:DB8:A:A::19 sequence 10

B. R3(ccnfig-ipv6-acl)#no sequence 30

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B host 2001:DB8:A:A::19 sequence 10 Most Voted

C. R3(config-lpv6-acl)#no sequence 20

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B any sequence 10

D. R3(config-ipv6-acl)#no sequence 30

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B any sequence 10

Correct Answer: B

Community vote distribution

B (100%)

Question #580 Topic 1

Which control plane process allows the MPLS forwarding state to recover when a secondary RP takes over from a failed primary RP?

A. LDP uses SSO to recover from disruption in control plane service. Most Voted

B. MP-BGP uses control plane services for label prefix bindings in the MPLS forwarding table.

C. FEC uses a control plane service to distribute information between primary and secondary processors.

D. LSP uses NSF to recover from disruption in control plane service.

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 29/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #581 Topic 1

Refer to the exhibit. An engineer recently modified the configuration for area 3 to accept only type 1, 2, and 3 LSAs. Immediately after the changes,

users connected to router R6 began to report connectivity issues. Which configuration restores connectivity to R6 and meets the requirement?

A.

B.

C.

D. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 30/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #582 Topic 1

Refer to the exhibit. Jitter on the link between R101 and R201 was tested for voice traffic over port 16384 without the control communication on

port 1967. Which command enables R201 to receive RTT for the configured IP SLA?

A. ip sla responder tcp-connect port 1967

B. ip sla responder udp-echo ipaddress 2.2.2.2 port 16384 Most Voted

C. ip sla responder udp-echo ipaddress 1.1.1.1 port 16384

D. ip sla responder auto-register 1.1.1.1

Correct Answer: B

Community vote distribution

B (92%) 8%

https://www.examtopics.com/exams/cisco/300-410/view/4/ 31/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #583 Topic 1

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

https://www.examtopics.com/exams/cisco/300-410/view/4/ 32/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Configure HUB and SPOKE routers according to the topology to achieve these goals:

1. Configure mGRE neighborship by using physical interface IP addresses to provide end-to-end reachability. Verify all router’s tunnel interfaces

accordingly.

2. Configure NHRP on HUB router as multipoint dynamic IP to NBMA mapping. SPOKE1 and SPOKE2 routers should be configured by using static

NHS and multicast mapping for HUB. Use network-id 10 for NHRP. Verify NHRP neighborship between routers and verify results using ping from

PC1 to PC2 and PC3 accordingly.

Correct Answer:

Question #584 Topic 1

Which tag is used by the PE router to forward the packet to the correct customer?

A. RD

B. extended-community

C. RT Most Voted

D. VNI

Correct Answer: C

Community vote distribution

C (75%) A (25%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 33/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #585 Topic 1

Refer to the exhibit. The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192.168.7.0/24

and 192.168.15.0/24 subnets. Which configuration resolves the issue?

A.

https://www.examtopics.com/exams/cisco/300-410/view/4/ 34/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

B.

Most Voted

C.

D.

Correct Answer: B

Community vote distribution

B (100%)

Question #586 Topic 1

Which routing protocol is used by the PE router to advertise routes to a CE router without redistribution or static after removing the RD tag from

the P router?

A. OSPF

B. BGP IPv4 Most Voted

C. IS-IS

D. MP-BGP

Correct Answer: B

Community vote distribution

B (80%) D (20%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 35/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #587 Topic 1

Refer to the exhibit. The default route is not advertised to the neighboring router. Which action resolves the issue?

A. Configure the default-information originate command under OSPF Most Voted

B. Configure OSPF on the Dialer0 interface.

C. Configure the redistribute static metric 200 subnets command under OSPF.

D. Configure the network 0.0.0.0 255.255.255.255 area 0 command under OSPF

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 36/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #588 Topic 1

Refer to the exhibit. An engineer must ensure that R3 sees only type 1 and 2 LSAs in area 1. Which command must the engineer apply on R2?

A. area 1 nssa no-summary

B. area 1 stub

C. area 1 stub nssa

D. area 1 stub no-summary Most Voted

Correct Answer: D

Community vote distribution

D (76%) B (24%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 37/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #589 Topic 1

Users report web connectivity problems on the server (10.1.1.10). Which IP SLA configuration captures the failure details through the network to

resolve the issue?

A.

B.

C.

Most Voted

D.

Correct Answer: C

Community vote distribution

C (63%) B (37%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 38/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #590 Topic 1

DRAG DROP

Drag and drop the terminology from the left onto the corresponding definitions on the right.

Correct Answer:

https://www.examtopics.com/exams/cisco/300-410/view/4/ 39/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #591 Topic 1

Refer to the exhibit. An engineer configures router A to mark all inside to outside traffic from network 192.168.1.0. except from host 192.168.1.1.

with critical IP precedence. The policy did not work as expected. Which configuration resolves the issue?

A.

B.

C.

https://www.examtopics.com/exams/cisco/300-410/view/4/ 40/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

D. Most Voted

Correct Answer: D

Community vote distribution

D (95%) 5%

Question #592 Topic 1

Which two label distribution methods are used by routers in MPLS? (Choose two.)

A. LDP discovery hello message

B. LDP session protection message

C. downstream unsolicited Most Voted

D. downstream on demand Most Voted

E. targeted hello message

Correct Answer: CD

Community vote distribution

CD (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 41/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #593 Topic 1

Refer to the exhibit. HostA and HostB cannot receive IP addresses from the DHCP server. The switches are configured with the DHCP snooping.

Which configuration on SW3 resolves the issue?

A. ip dhcp relay information option-insert

B. no ip dhcp snooping information option Most Voted

C. ip dhcp server use subscriber-id client-id

D. ip helper-address 1.0.0.2

Correct Answer: B

Community vote distribution

B (56%) D (44%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 42/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #594 Topic 1

What is a MPLS PHP label operation?

A. Downstream node signals to remove the label. Most Voted

B. It uses implicit-NULL for traffic congestion from source to destination forwarding.

C. PE removes the outer label before sending to the P router.

D. It improves P router performance by not performing multiple label lookup.

Correct Answer: A

Community vote distribution

A (80%) 10% 10%

https://www.examtopics.com/exams/cisco/300-410/view/4/ 43/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #595 Topic 1

Refer to the exhibit. EIGRP adjacency between router A and router C is not working as expected. Which two configurations resolve the issue?

(Choose two.)

A.

B.

C.

Most Voted

https://www.examtopics.com/exams/cisco/300-410/view/4/ 44/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

D.

Most Voted

E.

Correct Answer: CD

Community vote distribution

CD (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 45/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #596 Topic 1

Refer to the exhibit. Branch 2 hosts cannot receive dynamic IP addresses. Which action resolves the issue?

A. Configure the ip helper command on the Layer 2 switch SW2 interfaces.

B. Configure the ip helper command on the Interface GigabltEthernet 0/0 of the DHCP router.

C. Configure the ip helper command on the Interface GigabltEthernet 0/2 of the DHCP router.

D. Configure the ip helper command on the interface GigabltEthernet 0/2 of the R2 router. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 46/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #597 Topic 1

Which feature filters the IPv6 traffic on Layer 2 untrusted ports?

A. IPv6 Source Guard Most Voted

B. Binding Table Recovery

C. IPv6 RA Guard

D. DHCPv6 Guard

Correct Answer: A

Community vote distribution

A (100%)

Question #598 Topic 1

What are the two benefits of using BFD? (Choose two.)

A. synchronous path determination

B. subsecond failure detection Most Voted

C. supports ail routing protocols

D. supports UDLD failure

E. forwarding path failure detection Most Voted

Correct Answer: BE

Community vote distribution

BE (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 47/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #599 Topic 1

Refer to the exhibit. An engineer must troubleshoot an issue affecting the communication from router R2 to the TACACS server. Which

configuration resolves the issue?

A. R1 (config)#tacacs-server packet maxsize 43974

B. R2(config)#tacacs server advrt -

R2 (config-server-tacacs)#key xyz123 Most Voted

C. R2(config)#tacacs-server packet maxsize 43974

D. R1 (config)#tacacs server advrt -

R1 (config-server-tacacs)#kty xyz123

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/300-410/view/4/ 48/49
3/13/25, 8:33 AM 300-410 Exam - Free Actual Q&As, Page 4 | ExamTopics

Question #600 Topic 1

Refer to the exhibit. An engineer configured SNMP in R1 to be able to save and upload configurations to the SNMP server but failed when they

tried to backup R1 configuration on the server. Which configuration resolves the issue?

A. snmp server tftp-server-list 66 Most Voted

B. copy running-config tftp://10.66.66.66/r1-confg

C. snmp server tftp-server-list 20

D. copy running-config tftp://10.66.66.66/c: r1-confg

Correct Answer: A

Community vote distribution

A (100%)

 Previous Questions Next Questions 

Browse atleast 50% to increase passing rate

Viewing page 4 out of 5 pages.

Viewing questions 151-200 out of 620 questions

https://www.examtopics.com/exams/cisco/300-410/view/4/ 49/49