V20220398

MP6969-60
MOPA Laser Marking Machine
User Manual

Read Carefully Before Use

Keep for Future Reference
 PREFACE
Thank you for choosing our laser equipment.
This fiber laser marking machine is intended for personal and professional use.
Read this manual carefully before operation. It covers the details of correct installation, adjustment, maintenance,
and—most importantly—safe operation of your new laser. It is intended to be used in conjunction with the manual for
its engraving software, as the program not only provides image design but also serves as the main interface for the laser
settings and machine controls. You and any other users of this device should thoroughly understand BOTH manuals
before attempting to operate the laser.
Both manuals should be included if this device is given or sold to a third party.
If you have any questions, after reading these manuals, please contact us and our support department will address your
concerns as soon as possible.
 CONTENTS
1. Introduction.................................................................................................................................1
1.1 General Information ...........................................................................................................1
1.2 Symbol Guide.......................................................................................................................1
1.3 Designated Use.....................................................................................................................2
1.4 Technical Specifications ......................................................................................................2
1.5 Components ..........................................................................................................................3
2. Safety Information .....................................................................................................................6
2.1 Disclaimer ............................................................................................................................6
2.2 General Safety......................................................................................................................6
2.3 Laser Safety..........................................................................................................................6
2.4 Electrical Safety...................................................................................................................7
2.5 Material Safety.....................................................................................................................7
3. Installation ..................................................................................................................................9
3.1 Overview ..............................................................................................................................9
3.2 Location Selection ...............................................................................................................9
3.3 Electrical Grounding............................................................................................................9
3.4 Assembly ........................................................................................................................... 10
3.5 Control Computer ..............................................................................................................11
4. Operation...................................................................................................................................11
4.1 Overview ............................................................................................................................11
4.2 General Instructions...........................................................................................................11
4.3 Instructions for Specific Materials .................................................................................. 13
5. Maintenance............................................................................................................................. 14
5.1 Overview ........................................................................................................................... 14
5.2 Regular Procedures ........................................................................................................... 14
5.3 Troubleshooting ................................................................................................................ 15
5.4 Disposal Instructions ....................................................................................................... 15
6. Contact Information ................................................................................................................ 15
1 Introduction
1.1 General Information
This manual is the designated user guide for the installation, setup, safe operation, and maintenance of your fiber laser
marking machine. It is divided into six chapters covering general information, safety instructions, installation steps,
operation instructions, maintenance instructions, and contact information.
All personnel involved in the installation, setup, operation, maintenance, and repair of this machine should read and
understand this manual, particularly its safety instructions. Substandard performance and longevity, property damage,
and personal injury may result from not knowing and following these instructions.
Your fiber laser marker works by emitting a powerful laser beam from its fiber laser source, sending that beam through
a fiber optic cable, focusing its power through the galvanometer lens, and using this focused light to etch designs into
certain substrates.
This fiber laser marking machine uses a nanoscale fiber laser source. Its single-mode output, good heat dissipation,
high efficiency, and compact structure make it ideal for high-precision laser marking. With typical use, this device has
an average lifespan around 100,000 working hours. However, constantly running your laser above 80% of its maximum
rated power can significantly shorten its service life. It is recommended to use settings from 10–75% of the maximum
rated power to enjoy optimal performance and longevity.
Note that this is a high-voltage device and, as a safety precaution, it is recommended to only touch its components with one
hand at a time during use.
Note also that this device does not have a protective housing. It is thus recommended to use a special room or to raise
protective screens around the work area. The active laser is invisible to the human eye and anyone in or near the working
area MUST use special protective eyewear when the laser is in use to avoid potentially permanent injury.

1.2 Symbol Guide

The following symbols are used on this machine’s labeling or in this manual:

These items present a risk of serious property damage or personal injury.

These items address similarly serious concerns with regard to the laser beam.

These items address similarly serious concerns with regard to electrical components.

Protective eyewear should be worn by anyone around this machine during operation.

This product is sold in conformity with applicable EU regulations.

This product contains electrical components that should not be disposed of with regular garbage.

1
1.3 Designated Use
This machine is intended for use engraving signs and other consumer products on applicable substrates. This laser can
process a wide variety of metals including steel, aluminum, titanium, brass, copper, tungsten, carbide, and chrome. It can
also be used with stone and some hard plastics such as acrylic. (See §§2.5 & 4.3 for further details.) Use of this system for
non-designated purposes or materials is not permitted.
The system must be operated, maintained, and repaired by personnel familiar with the field of use and the dangers of the
machine and the material being engraved including its reflectivity, conductivity, potential for creating harmful or
combustible fumes, etc.
Laser beams are dangerous. The manufacturer and/or seller bear(s) no responsibility and assume(s) no liability for any
improper use of this device or for any damage or injury arising from such use. The operator is obliged to use this fiber
laser marker only in accordance with its designated use, the other instructions on the device and in its manuals, and all
applicable local and national laws and regulations.

1.4 Technical Specifications

Model LYF-60W

Input Power 110V/60Hz

Rated Power 60W

Expected Service Life 100, 000 hr.

Laser Wavelength 1064 nm (1.064 µm)

Laser Frequency 1-4000 kHz

Processing Area 6.9×6.9 in. (17.5×17.5 cm)

Max. Marking Speed 275.6 ips (700 cm/s)

Min. Marking Depth 0.0002 in. (0.005 mm)

Max. Marking Depth 0.003 in. (0.07 mm) on a single pass

Min. Line Width 0.006 in. (0.15 mm)

Precision ±0.1 µm

Required Operating Environment <70% Humidity and 40–95°F (5–35°C)

Required Operating Software EZCad

2
1.5 Components

B
C

E
F

Main Parts
A. Support Column—The support column holds the laser arm and includes a precise graduated rule for quickly
adjusting height to work with different materials and thicknesses.
B. Height Adjustment Knob—This wheel moves the laser arm up and down for the correct alignment across different
materials and thicknesses.
C. Galvo Lens Head—The high-speed galvanometer scanning head focuses the laser beam to a fine point, directing it
to proper locations on the target material during engraving.
D. Laser Cable—This transmits the laser beam from its source to the galvonometric lens.
E. Worktable—This platform holds the target material, with optional positioning bars to ensure precise
alignment.
F. Main Tower—This houses the fiber laser source, its mainboard, and various connections.

3
 A

D
C
E

Main Tower
A. Stepper Motor—This motor helps control attached rotary axes.
B. Mainboard—This circuit board works with your software to control the laser.
C. Mainboard Power Supply—This device draws 0.5A to convert standard electricity to 5V 3A power for the mainboard.
D. Laser Power Supply—This device draws 6.8A to convert standard electricity to 24V 14.6A power for the fiber laser
source.
E. Galvanometer Power Supply—This device draws 2.5A to convert standard electricity to 15V 2A power for the scanning
lens.
F. Fiber Laser Source (Inside Casing)—This component creates the laser beam and transfers it to the fiber optic pathway
to the scanning lens.

Connection Inputs
A. Laser Cable—This transmits the laser beam from its source to the
galvonometric lens.
B. USB Cord Input—This port connects the device to your control
computer.
C. Interlock & Fan Cable—This cable input enables the option to
power the interlock and exhaust fan of a protective covering.
A B
D. Foot Pedal Cord Input—This port enables optional pedal control
of laser activation to free your hands for manual adjustment of the C
target material.
E. Rotary Axis Cord Input—This port enables use of a rotary D
axis engraver with a 4-pin connection cable. (Compatible
rotary axis devices are sold separately.) E
F. Power Cord Input—This 3-pin port connects to the device's
standard 3-prong power cord. F

4
 A B C

Power Buttons
A. Emergency Stop—Because of the risk of fire and other hazards during engraving, this engraver includes a
large and easy-to-reach emergency stop button near the control panel. Press it down to stop the laser instantly.
B. Total Power—Activates the mainboard inside the main tower and the galvanometer head inside the main arm.
Insert your key and turn this first during startup and last during shutdown.
C. Fiber Laser—Activates the laser source. Press this last during the startup and first during shutdown.

Command Tool Bar

View Tool Bar
Object
List
Drawing Tools
Laser Marking
Parameters

Object
Properties
Laser Marking
Controls
Status Bar

Control Computer
This fiber laser marker is controlled by the included EZCad software, which must be installed on a compatible
computer to direct the laser. See its separate manual for full details on its components and use. Some features
which are particularly important to note include the following parameters and controls:
• Loop Count—Specifies how many times the laser beam will repeat its path, creating greater contrast in the
marked image.
• Speed—Specifies the speed of the beam in millimeters per second, with greater speed creating less contrast in
the marked image.
• Power—Specifies the % of the machine's rated power that will be used, with greater power creating greater
contrast. Note again that running the machine at greater than 80% power will shorten its service life and
10–75% is recommended for most applications.
• Frequency—Specifies the laser’s frequency in kilohertz (kHz), with higher frequency producing a denser laser
mark and darker engraving.
• Red (F1)—Tells the laser guidance to illuminate the current laser path.
• Mark (F2)—Fires the laser beam for testing and focus improvement.

5
2. Safety Information
2.1 Disclaimer
Your engraver may differ somewhat from those shown in this manual due to options, updates, etc. Please contact
us if your marking machine came with an outdated manual or if you have any other questions.

2.2 General Safety Instructions

• Use this laser marking device only in accordance with all applicable local and national laws and regulations.
• Use this device only in accordance with this instruction manual and the manual for the engraving software included
with it. Only allow this device to be installed, operated, maintained, repaired, etc. by others who have also read and
understood both manuals. Ensure that this manual and the software manual are both included with this device if it is
ever given or sold to a third party.
• DO NOT operate this device continuously for more than 5 hours. Stop every 5 hours for at least
½ hour.
• DO NOT leave this device unattended during operation. Observe the device throughout operation
and, if anything seems to be operating strangely, immediately cut off ALL power to the machine
and contact either our customer service or your dedicated repair service. Similarly, ensure the
device is FULLY turned off in the correct order after each use.
• DO NOT allow minors, untrained personnel, or personnel suffering from physical or mental impairment that would
affect their ability to follow this manual and the software manual to install, operate, maintain, or repair this device.
• Any untrained personnel who might be near the device while it is in operation MUST be informed that it is dangerous
and fully instructed on how to avoid injury during its use.
• Always keep a fire extinguisher, water hose, or other flame retardant system nearby in case of accidents. Ensure that
the local fire station's phone number is clearly displayed nearby. In the case of a fire, cut electrical power before
dousing the flame. Familiarize yourself with the correct range for your extinguisher before use. Take care not to use
your extinguisher too close to the flame, as its high pressure can produce blowback.

2.3 Laser Safety Instructions

This machine uses an invisible CLASS 4 LASER, the strongest and most dangerous class of laser available for
public use. Used without care, it can cause serious property damage and personal injury including but not limited
to the following:
• The laser will easily burn nearby combustible materials
• Some working materials may produce radiation or harmful gasses during processing
• Direct exposure to the laser will cause bodily harm including serious burns and irreparable
eye damage
As such,
• NEVER interfere with the laser beam.
• DO NOT place any part of your body under the laser lens during operation. Take measures to protect yourself from
potentially reflected laser beams including the use of screens or personal protective equipment.
• NEVER attempt to view the laser directly without protective eyewear. Always wear safety goggles or glasses designed
to filter the specific wavelength of your engraver's laser with an optical density (OD) of 5+. As even seemingly matte
materials can produce harmful reflected beams, care should be taken to keep anyone without protective eyewear
from observing the machine during operation. EVEN WITH protective eyewear, do not stare or allow others to
stare continuously at the laser beam during operation.
• DO NOT leave potentially combustible, flammable, explosive, or corrosive materials nearby where they could be
exposed to the direct or reflected laser beam.

6
• DO NOT use or leave sensitive EMI equipment nearby. Ensure the area around the laser is free of strong electromagnetic
interference during any use.
• ONLY use this machine as described in the Material Safety section of this manual. The laser settings and engraving
process must be properly adjusted for specific materials.
• Ensure the area is kept free of airborne pollutants, as these might pose a similar risk of reflection, combustion, etc.
• NEVER use this marking machine with the fiber source’s housing opened, as the closed laser light path is necessary
to prevent laser radiation leakage.
• DO NOT modify or disassemble the laser and do not use the laser if it has been modified or disassembled by anyone
except trained and skilled professionals. Dangerous radiation exposure and other injury may result from the use of
adjusted, modified, or otherwise incompatible equipment.

2.4 Electrical Safety Instructions

• ONLY use this device with a compatible and stable power supply with less than 5% fluctuation in its voltage.
• DO NOT connect other devices to the same fuse, as the laser system will require its full amperage. Do not use with
standard extension cords or power strips. Use only surge protectors rated over 2000J.
• ONLY turn on the power to this device when it is well grounded, either via a firm connection to
a 3-prong outlet or via a dedicated grounding cable firmly connected to the proper slot on the back
of the main tower. Do not use with an ungrounded 3 to 2 prong adapter. The device's grounding
should be checked regularly for any damage to the line or loose connections.
• Turn the device on and off using its power buttons in the correct order. The laser has a separate
power supply that is separately grounded. Pushing all the buttons at once, too quickly, or in the
wrong order may send electrical current to an ungrounded component, causing short circuits and
other electrical hazards.
• ONLY use this device with one hand at a time. The laser is powered by an extremely high voltage connection
and placing two hands on the machine at one time during operation has the potential to create a closed circuit with
the human body, resulting in electrical shock.
• The area around this laser marking device should be kept dry, well ventilated, and environmentally controlled to
keep the ambient temperature between 40–95°F (5–35°C). The ambient humidity should not exceed 70%.
• Adjustment, maintenance, and repair of the electrical components of this device must be done ONLY by trained
and skilled professionals to avoid fires and other malfunctions, including potential radiation exposure from
damage to the laser components. Because specialized techniques are required for testing the electrical components
of this marking system, it is recommended such testing only be done by the manufacturer, seller, or repair service.
• Unless otherwise specified, ONLY undertake adjustment, maintenance, and repair of the device when it is turned
off and disconnected from its power supply.

2.5 Material Safety Instructions

• Users of this fiber marking machine are responsible for confirming that materials to be processed can withstand the
heat of the laser and will not produce any emissions or byproducts either harmful to people nearby or in violation of
any local or national laws or regulations. In particular, do not use this device to process polyvinyl chloride (PVC),
teflon, or other halogen containing materials under any circumstances.
• Users of this fiber laser are responsible for ensuring that every person present during operation has sufficient PPE to avoid
any injury from emissions or byproducts of the materials being processed. In addition to the protective laser eyewear
discussed above, this may require goggles, masks or respirators, gloves, and other protective outer clothing.
• Users must exercise special caution when working with conductive materials as buildup of their dust and ambient
particles may damage electrical components, cause short circuits, or produce other effects including reflected laser
radiation.

7
This machine can be safely used with the following materials:
• Aluminum
• Brass
• Carbide
• Gold
• Silver
• Steel
• Stone, including Granite, Marble, etc.
• Titanium
• Tungsten

This machine can be used with some other metals, hard plastics, and other materials with some care. For other materials,
if you are unsure about its safety or laserability with this device, seek out its material safety data sheet (MDS).
Pay especial attention to information about safety, toxicity, corrosiveness, reflectivity, and reaction(s) to high
heat. Alternatively, contact our support department for further guidance.

See §4.3 for the recommended parameters for the most commonly engraved materials.

This machine CANNOT be used with the following materials or with any materials which include them:
• Artificial Leather containing Hexavalent Chromium (Cr[VI]), due to its toxic fumes
• Astatine, due to its toxic fumes
• Beryllium Oxide, due to its toxic fumes
• Bromine, due to its toxic fumes
• Chlorine, including Polyvinyl Butyrale (PVB) and Polyvinyl Chloride (PVC, Vinyl, Cintra, etc.), due to its toxic fumes
• Fluorine, including Polytetrafluoroethylenes (Teflon, PTFE, etc.), due to its toxic fumes
• Iodine, due to its toxic fumes
• Paper and Paperboard, due to their high flammability when exposed to the concentrated laser
• Phenolic Resins, including various forms of Epoxy, due to their toxic fumes
• Wood, including MDF, Plywood, Balsa, Birch, Cherry, Oak, Poplar, etc., due to its high flammability

8
3. Installation
3.1 Installation Overview
A complete working system consists of the fiber laser source, the laser arm with the galvanometer lens, a computer (not
included) with engraving software (included), and all applicable connection cables. A support column and workbed
come included to assist your work. Users can also configure other additional accessories (such as a rotary axis) to suit
their needs.
Use only the hardware, wiring, and power sources that came with or are compatible with this device.
Installing equipment that your device is not designed to work with can lead to poor performance,
shortened service time, increased maintenance costs, property damage, and personal injury.
Please note the specific requirements of your system's installation. Every customer must understand these notes before
installation to execute a proper setup and achieve safe laser performance. If you have any installation questions or
problems, contact our technicians and customer support team.
Any auxiliary equipment must be adjusted to the base machine. Queries may be directed to the dealer or manufacturer
of such equipment.

3.2 Location Selection

Prior to assembling your fiber laser marker, select an appropriate location for its use.
Be sure that it meets all of the requirements discussed in the Safety Information above. The location should be stable,
level, dry, and climate controlled to ensure an ambient temperature 40–95°F (5–35°C) and an ambient humidity under
70%. In particular, the temperature and humidity together should not be close to the dew point. It is also advisible to
use a windowless room or to use blinds and/or curtains to avoid exposure to the potential additional heat of direct
sunlight. The location should be free of dust and other airborne pollutants and well ventilated enough to process any
fumes produced by the engraving process in accordance with all applicable laws and regulations. Depending on
the materials to be processed, this may require construction of a dedicated ventilation system. It should be away
from children; combustible, flammable, explosive, or corrosive materials; and sensitive EMI devices. The power
cord should be plugged into a compatible and stable power source via a grounded 3-prong outlet. No other item
should be drawing current from the same fuse. There should be fire-fighting equipment nearby and the local fire
station's phone number should be clearly displayed.
It is highly recommended to have an extra work table nearby in order to avoid placing objects on or directly adjacent to
the machine, which could become a fire or laser hazard.

3.3 Electrical Grounding

This device employs a powerful laser. As discussed in the Safety Information above, it is extremely high voltage and
potentially dangerous, so users must securely ground it to avoid the buildup of static electricity. Using a standard
3-prong outlet will provide sufficient grounding. If you do not have access to a 3-prong outlet, you MUST use the
grounding cable and ensure its proper connection. The far end of the cable should be securely connected to a metal rod
driven at least 8 feet (3 m) deep into soil located at least 5 feet (1.5 m) from the machine. The resistance along the line
should be no greater than 5Ω.

Poor grounding WILL cause equipment failure and create a serious electrical shock hazard. The
manufacturer and/or seller bear(s) no responsibility and assume(s) no liability for any damage,
accidents, or injuries caused by bad grounding connections.

9
3.4 Assembly Instructions
Step 1. Install the support column onto the worktable using the four mounting holes and the provided bolts.

Step 2. Install the laser arm onto the support column using the provided bolts.

Mount the laser arm so that its lens Align the four holes on the housing Tighten it into place with the included
box is positioned over the work area. with the holes in its mounting bracket. bolts.

Turn the knob on top of the support column to adjust the height of the laser arm to about 24 cm (9.4 in.), as
marked on the column's ruler. This will position the lens to be nearly in focus with most common materials.

Step 3. If desired, attach the monitor bracket to the support column using the included bolts and then mount the control
computer monitor onto the bracket.

Step 4. Make all necessary connections between the various components.

Step 5. The positioning bars can be installed onto the worktable and left in place for all your projects or can be moved
around to suit different projects. Simply place the bars over the holes that will form the outer edge of the target
material and fasten them into place with the provided bolts.

10
3.5 Control Computer Installation
See the separate engraving software manual for details on the requirements for the control computer. The control
computer should not be placed more than 15 feet (4.5 m) away from the fiber laser marker in order to avoid possible
interference to the signal in its line. Familiarize yourself with your software's image design features and laser control
settings before beginning operation of the laser itself.

4. Operation
4.1 Operation Overview
Operate this laser marking machine only in accordance with all the instructions provided in this manual. Failure to
follow the proper guidelines detailed here can result in property damage and personal injury.
This section will address only some of the options and features provided by the operation software. Before beginning to
use the machine, make sure that you have read this entire manual (particularly the Safety Information above), the
separate software manual, and any and all warnings provided on the machine itself.

4.2 General Operation Instructions

Step 1. Load or create a design in EZCad.

Step 2. Put on your protective eyewear. Ensure that anyone else who might bet exposed to direct or reflected
laser beams is also wearing protective eyewear as described in §2.4.
Step 3. Turn on the laser marker by using your passkey and then activating the laser power supply.
Activating them out of order may cause electrical hazards as the separate power supplies are grounded
in order. Do not press the buttons too quickly. Give each power supply time to come on line, activating
its fans. 3 seconds is sufficient.
To reduce the risk of electric shock, once the engraver is on, try to touch its components with only one
hand at a time.

11
Step 4. If you previously disconnected the control computer, reconnect it via the USB cable now. If your computer is
already connected and EZCad is already running, restart it now to establish a connection between the computer
and the laser’s control board.
Step 5. Customize your contrast and engraving depth by adjusting the engraving parameters in EZCad.
To darken an image, use a higher frequency setting. To lighten it, use a lower one. To increase engraving
depth, increase the amount of energy per unit area by reducing the speed parameter or increasing the laser's
power or the number of loops. Engraving too deep, however, reduces image quality, especially for coated
materials. Again, constantly using settings over 80% will shorten the expected service life of your laser.
Resolution should usually be set to 500 dots per inch. Reducing your image resolution can be helpful in some
cases, reducing flaming and increasing the energy of the pulse in a way that improves the quality of the resultant
image in some materials such as some plastics.
Step 6. Activate the laser guidance system by pressing Red or hitting F1 in EZCad. The design should be displayed
in red light on the worktable, showing where the laser will fire.

Step 7. Place an expendable piece of the material to be engraved in the location shown by the laser guidance. Do not
use a different target as the galvanometer lens automatically focuses at different heights for different materials.
Being careful that no part of your body is near the worktable or laser path, press Mark or hit F2 in EZCad to
fire the test laser. Alternatively, you can activate the laser by using the foot pad.
Step 8. The laser is invisible but will create a buzzing noise and sparks and begin engraving when it is correctly focused
on your test material. If no sparks are emitted, the laser is out of focus. Continue to fire it while adjusting the
laser arm up or down using the height adjustment wheel on the support column. Small, consistent sparks will
be emitted at the marking point when the beam is correctly in focus. Make a note of the correct height on the
support column's ruler for future reference.

In Focus Out of Focus

12
Step 9. Replace the test material with the actual material. Use the foot pad or press Mark or hit F2 in EZCad to
engrave your pattern. Again, do not stare at the laser in operation even with protective eyewear. Watch for
possible issues like sparks or fires, however, and be prepared to quickly extinguish a fire if necessary.
Step 10. Examine the quality of your first run and adjust the laser parameters in EZCad as necessary to create your
desired effect. The foot pedal is particularly useful for continuous or repeated operation of the laser once
you've settled on your design and its ideal parameter settings. You can also achieve more control of the
marking process by reducing the laser's speed and using the foot pad.
Step 11. When you have finished engraving your design, close EZCad and then turn off the laser marking machine
by deactivating the systems in order, first the laser power supply and then the main key.
Step 12. Cover the galvonometer lens and fully clean the workbed. For best results, disconnect your fiber marking
machine from its power supply between uses. Unplug it or turn off its intermediary surge protector.

4.3 Instructions for Specific Materials

When engraving a new material, it can be helpful to engrave a test matrix of small boxes produced with various speed,
power, and frequency settings to home in on the exact effect that you are looking for. To speed the process, here are
some general guidelines for commonly engraved materials. Again, however, these are only guidelines for your conve-
nience and it is the responsibility of the user to consult material safety data sheets and other sources to ensure the safety
of working with various materials and setups. Some of the materials listed will require additional workspace and
personal protective equipment in addition to this engraver:

Metals
When engraving metals, generally use high power, a low frequency, and low to medium speed settings. To avoid
using your marker at greater than 80% power for extended periods, you can also get similar effects by reducing
the power somewhat while also increasing the number of passes or decreasing the engraving speed. Be mindful
that some metals will produce conducting, reflective, and/or toxic dust. Softer metals naturally produce more
dust during engraving, while harder metals can require higher power settings that also produce more dust. In
addition to the risk to the user's skin and eyes, there may be enough dust produced (especially for repetitive
industrial applications) that a full ventilation system is required to address the problem. Similarly, operators and
others in the work area may need to use breathing PPE such as masks and respirators.
Aluminum: Bare aluminum requires a somewhat higher frequency than other metals and will never produce a strong
black mark similar to those created by engraving steel. When darker marking is required, consider employing anodization
or producing a deep engraving that can be darkened by using black epoxy or other filler. Anodized aluminum requires
a little more speed but a very low frequency.
Powder Coated Metals: Metals with a powder coating usually require a very high frequency and, for best results, at
least 3 passes to remove the coating and polish the bare lower layer.
Precious Metals: Gold and similarly soft metals should be engraved with less power but a moderate speed. Silver and
other semidurable metals are best engraved at a slightly higher power and slightly slower speed, but still not at the
same power and speed as steel or aluminum.

13
Plastics
When engraving plastics, generally use low power and high speed settings. Marking and engraving with too much
power or at too low a speed can concentrate too much energy at the point of contact, causing the plastic to melt. Among
other problems, this may produce poor engraving quality, noxious fumes, and even fires.

Stone
When engraving various kinds of stone, generally use moderate power and speed at low frequency. As with ceramics
and metals, be mindful of the dust created (especially for repetitive industrial applications) and take similar measures
to ensure the safety of users and others in the work area.

5. Maintenance
5.1 Maintenance Overview
Unless otherwise specified, ONLY perform adjustment and maintenance of this device when the power is
turned off and the power supply has been disconnected. ONLY allow trained and skilled professionals to
modify or disassemble this device.

5.2 Regular Maintence Procedures

• Keep the workroom clean and dust-free at all times.
• Ensure the device is fully powered off when not in use.
• Cover the galvanometric lens when it is not in use.
• Clean the worktable after use with a cloth wetted with greater than 75% rubbing alcohol. NEVER clean this device
with abrasive or caustic cleansers, with aerosol sprays, or with enough water to enter any electrical component.
Always allow surfaces to fully dry before further use.
• If removing dust from the device's vents using a vacuum, ONLY use the lowest power setting to avoid damage to
internal components.
No other servicing should be done by the operator. Do not attempt to service or replace other parts yourself.

14
5.3 Troubleshooting Guidance

Potential Problems Possible Solutions

Correct the focus by adjusting the height of the laser arm.

Correct the software parameters if they are invalid or mistaken.

Have a technician fix or establish the connection between the laser and the mainboard.
No Laser Output
Have a technician fix or establish the connection between the laser and its power supply.

If either the fiber laser source or its power supply have worn out, have a technician
replace them.

Confirm that the material can be safely engraved with this device.

Correct the focus by adjusting the height of the laser arm.

No Engraving
Adjust the software parameters to create greater intensity.
despite Laser Output
Have a technician check the control panel, scanning lens, and its power supply. Correct
any problems or replace the part.

Have a technician check the fiber laser source and the mainboard. Correct any problems or
Other Laser Errors replace the part.

5.4 Disposal Instructions

Electrical products should not be disposed of with household products. In the EU and UK, according to the
European Directive 2012/19/EU for the disposal of electrical and electronic equipment and its implementa-
tion in national laws, used electrical products must be collected separately and disposed of at the collection
points provided for this purpose. Locations in Canada and the US may have similar regulations. Contact
your local authorities or dealer for disposal and recycling advice.

Contact Us
Thank you for choosing our laser equipment for your home or shop! For a .pdf copy of
the latest version of this manual, use the appropriate app on your smartphone or
other device to scan the QR code to the right.
Come join the OMTech community at our official laser group on Facebook or visit the
company forums at omtechlaser.com! Check our YouTube channel for helpful hints
and instructional videos. If you encounter any problem regarding your engraver, do not
hesitate to contact customer service with your order number at [email protected]
or [email protected]. Our teams will respond within 24 hours to make
things right. You can also reach us Monday to Friday at (949) 539-0458 between 8 am
and 4:30 pm PST.
Thank you and we hope you will choose us again for all your laser needs!

15
FMM-J6W2-US
Rev. 20 Apr. 2022