Defoaming, Degassing Pump
DP, ASP types (PAT.)
Highly efficient and quick degassing of gas-dissolved li
B
T
C
>
This defoaming/degassing pump, with an interlocked vacuum pump, extrac
dissolved gas in liquid with surprising efficiency.
Degasses liquid mechanically without using any chemical additive such as hydrazine
not cause contamination, and greatly reduces maintenance costs.
We also manufacture pumps that meet sanitary specifications.
Principle of degassing (PAT.)
DP
type
When pumping liquid flows through
part of the pump, the dissolved ga
from the liquid by decompression,
liquid mixture is fed to the inducer
The liquid in the gas-liquid mixture
periphery and stratified by rotation
gas accumulates in the central are
same time.
ASP
The gas remaining in the liquid is f
type
liquid, as such liquid stratum is bro
vacuum.
The gas is then drawn out by the v
impeller.
Any remaining liquid in the gas dra
pump is separated by the impeller,
intake side of the inducer.
Defoaming/Degassing Pump ASP type
Principle of Defoamin
Surprising degassing efficiency!
The above is a typical example of defoaming/degassing pump's degassing pe
Please contact us for more in
The outstanding degassing power is evident by the reduction of dissolved oxygen fr
intake side (raw water at 20 degree C) to 0.5mg/L or less at the outlet side.
Defoaming of thickener solution
We are holding an "Online Exhibition" wh
experience the same kind of tour as a re
web.
Many videos showing actual examples of
processing various liquids and evaluation
defoaming and degassing results are ava
(> "Online Exhibition" page)
Continuous defoaming/degassing can be
low cost even for food and beverage pro
YOKOTA defoaming/degassing technolog
technology that has been featured in news articles.
For details of the news articles, please refer to "Current Topics: Defoaming, De
:
Overseas team
Inquiries
Tel : +81 82-241-8672
The "YOKOTA Defoaming/Degassing Pum
ASP type" received the 19th Nissyoku
Excellent Food Machinery/Material Award
the machinery category.
The 19th Nissyoku Excellent Food Machin
ceremony, established by the Japan Food
held September 9th, 2016 in the Dai-ichi
Minato Ward, Shinbashi) where the comp
Defoaming/Degassing Pump ASP Type re
the machinery category.
The Nissyoku Excellent Food Machinery/Material Award was established by the
Co. Ltd., in 1998, aimed at the development of machinery and robots supportin
and materials industry, and to reward and show appreciation for their contribu
being the 19th time that the award was presented. The target products include
machinery/robots, intermediate materials/sub-intermediate materials, and the
them, which are useful to the quality improvement of food products and suppo
such as food product-related machinery/robots/apparatus and their software, i
materials/sub-intermediate materials for packaging containers, food additives,
ingredients, and functional raw materials. The awards are decided by a selecti
up of representatives in various food industries and academics who discuss wi
other in reaching decisions.
The company's "Defoaming/Degassing Pump ASP Type" enables the instant an
removal of wasteful foam, bubbles and gas occurring in the food product manu
and it has been credited with contributing to the improvement of product qual
efficiency, which led to it winning the 19th Nissyoku Excellent Food Machinery/
machinery category.
:
Overseas
Inquiri
team
es
Tel:+81 82-241-
8672
Applications
Defoaming/degassing treatment of liquid foods and dairy products in each produc
boiling, immersion, extraction, oil extraction, mixing, fermentation, and preservat
and transfer of liquid products before bottling
<Application example>
Milk, soy milk, fruit juice, vegetable juice, vegetable paste, mustard, egg mixture,
ketchup, various juices, tea, fermented liquid, yeast liquid, cream, jelly, vinegar, s
seasonings, other
Supply of degassed water for high quality (high transparency) ice making
Prevention of malfunction of various measuring instruments (flow meter, density m
Defoaming/degassing and transfer of various raw material liquids
<Application example>
Various coating liquids, water-based paints, UV curable paints, urethane-based pa
pigments, adhesives, chemical raw materials, grinding oil, light oil, water-based p
desulfurization liquid, rinse, detergent, gel, calcium carbonate, other
Outstanding performance is also demonstrated in applications such as extraction fro
tanks), and suction and transfer of liquid containing large amounts of gas, foam and
YOKOTA's proposal: Troubled with stubborn foam and bubbles ? ........ The
solution to the problem.
What if the ASP type pump, originally designed for degassing, is
applied to defoaming ?
As expected, the defoaming tests have proven excellent defoaming
performance as indicated below.
I. Examples of defoaming in the actual liquid (Click on the picture for enlargement. )
1. Soy milk 2. Beverage concentrated liq
90 degree C, Specific gravity 1.02 (before 30 degree C, Specific grav
defoaming 0.6), Viscosity 30mPa-s 500mPa-s, Air-content rat
Improvement of production efficiency Enhancement of yield rate
3. Gelatin products 4. Pickling liquid
70 degree C, Specific gravity 1.28, Viscosity 6 degrees C, Specific grav
2000mPa-s, Micro foam 80mPa-s
Improvement of quality (commodification with Improvement of quality
high transparency)
5. Cream (food) 6. Egg yolk
50 degree C, Specific gravity 1.2, Viscosity 5 degree C, Specific gravi
4000mPa-s, Micro foam 7000mPa-s
Improvement of quality Improvement of quality
7. Mekabu (thick seaweed leaves) 8. Water-soluble paint
15 degree C, Specific gravity 1.07 (before Room temperature, Speci
defoaming 0.8) Viscosity 30mPa-s
Improvement of filling defect Improvement of coating d
9. Water-soluble paint 10. Solvent-based urethane
Room temperature, Specific gravity 1.1, 30 degree C, Specific grav
Viscosity 400mPa-s 3000mPa-s
Recycling of recovered paint Improvement of coating d
of defoaming time)
11. Adhesive 12. Glue
20 degree C, Specific gravity 1.04, Viscosity 25 degree C, Specific grav
1100mPa-s 10000mPa-s
Improvement of coating defects Improvement of coating d
13. Natural resin 14. Facial cleansing gel
75 degree C, Specific gravity 1.07, Room temperature, Speci
Air-content ratio 15% Viscosity 4000mPa-s
Improvement of working efficiency Stabilization of filling amo
(filling defects)
15. Gel (pharmaceuticals) 16. Grease
30 degree C, Specific gravity 1.1, Viscosity 25 degree C, Specific grav
30000mPa-s unmeasurable
Improvement of measurement precision Improvement of quality de
The above is defoaming example by ASP type. Please contact us for more info
II. Examples of defoaming test
Defoaming test equipment (ASP-0310 3.7kW-2900min-1 / Water ring vacuum pump
Test results with various kinds of liquid are shown in Fig.1-Fig.3.
Curves on the left side of each figure show the relation between flow rate and total
depending on gas amounts (0%, 50%, 60%, 70%).
A curve on the right side of each figure shows the relation between the gas amount
and the gas amount (%) at the outlet side.
Calculation of defoaming efficiency is as follows:
For example, if the gas amount is 70% at the intake side and 20% at the outlet side
Defoaming efficiency = 1 - (Gas amount at outlet side / Gas amount
at intake side) = 71.4%
Fig.1 Defoaming of normal water
The graph indicates removal of approx. 95-98% of foam (gas bubbles) from normal
Fig.2 Defoaming of green tea
The graph indicates removal of approx. 92-95% of foam from green tea in a conditi
(tea powder dissolved at the ratio of 0.55g powder/80cc water).
Fig.3 Defoaming of detergent
The graph indicates removal of approx. 67-72% of foam from detergent dissolved in
Despite the propensity of detergent to produce large quantities of difficult-to-remov
equipment performed well.
The above test results prove our degassing equipment's surprising defoaming effici
capability of continuous processing.
Moreover, YOKOTA Degassing Equipment enables remarkable cost reducti
various foaming liquids.
No clogging problems like that with membrane type equipment, no troublesome
and the pumps easily meet sanitary specifications.
Time required to eliminate foam and bubbles has been shortened, making it unn
tank for stabilization of liquid.
The stirring operation of the built-in impeller simultaneously provides favorable r
homogenization and reduced particle size.
With the self-priming and pressurized discharge capabilities, all processes includ
defoaming and transfer of liquid are achieved in this single, compact pump, unlik
which require installation of several components.
Use of YOKOTA Degassing Equipment greatly reduces costs of liquid processing.
Equipment suitable for defoaming relatively large amounts of liquid is also available
For details, please refer to Defoaming Pump UPSA type.
Selection chart & Outer dimensions
DP type
Specifications (normal water) Base pl
Flow Total Rotatio
Model
rate head n Bore
No. A B C D E F G K L M N
(L/min (MPa speed Suction/Discharge/VP
) ) (min-1)
DP- 17 17 11 15 12 2 10 31 60
10 0.05 1800 Rc1 /Rc1/2 /Rc1/2 64 800
0150 4 0 2 0 0 8 0 0 0
DP- 22 17 11 18 16 2 10 31 60
35 0.05 1800 25 /25 /25 86 800
0300 0 0 8 5 0 8 0 0 0
DP- 24 19 13 21 17 2 12 105 31 80
60 0.05 1800 50 /40 /40 89
0500 4 5 0 0 0 6 5 0 0 0
DP- 10 28 22 15 23 18 2 15 125 36 95
90 0.05 1800 65 /50 /50
0600 0 6 0 0 5 0 2 0 0 0 0
DP- 11 31 25 17 27 20 2 20 135 40 95
150 0.05 1800 80 /65 /65
0800 2 4 0 0 0 0 2 0 0 0 0
DP-S type (Sanitary specification)
Model No. Specifications (normal water) Base p
Flow Total Rotatio Bore A B C D E F G K L M
n
rate head Suction/Discharge/V
speed
(L/min) (MPa) P
(min-1)
DP- 18 17 11 15 14 30
10 0.05 1800 15A/15A/1S 71 28 80 850
0150S 1 0 2 0 0 0
DP- 20 17 11 16 14 30
35 0.05 1800 1S/1S/1S 71 28 80 850
0300S 5 0 8 5 5 0
DP- 23 19 13 18 14 115 40
60 0.05 1800 2S/1.5S/1.5S 77 26 80
0500S 2 5 0 0 5 0 0
DP- 26 22 15 21 16 120 40
90 0.05 1800 2.5S/2S/2S 83 22 80
0600S 9 0 0 0 5 0 0
DP- 28 25 17 24 18 25 145 55
150 0.05 1800 2.5S/2.5S/2.5S 81 22
0800S 3 0 0 0 5 0 0 0
The DP-0800S type is equ
ASP type
Specifications (normal water) Base p
Flow Total Rotati
Bore
Model No. rate head on
Suction/Discharg A B C D E F G K L M N
(L/min (MPa speed
e/VP
) ) (min-1)
ASP- 0.0 126. 17 16 14 30 45
10 2900 15 /15 /20 270 80 94 40 730
0115 5 5 0 4 0 0 0
ASP- 217. 17 16 13 17 35 54
35 0.1 2900 25 /25 /25 92.5 90 55 880
0310 5 0 0 0 0 0 0
ASP- 17 19 11 17 52. 22 113 52 69
60 0.1 2900 50 /40 /40 255 120
0510 0 5 0 0 5 0 0 5 0
ASP- 19 22 12 18 27 139 52 84
90 0.1 2900 65 /50 /50 298 139 60
0610 5 5 5 5 5 0 5 0
ASP-S type (Sanitary specification)
Specifications (normal water) Base
Flow Total Rotatio
Bore
Model No. rate head n
Suction/Discharge/ A B C D E F G K L M
(L/min (MPa speed
VP
) ) (min-1)
ASP- 24 10 17 13 23
10 0.05 2900 15A/15A/1S 80 75 40 80 700
0115S 5 1 0 5 0
ASP- 24 12 17 16 11
35 0.1 2900 1S/1S/1S 95 55 80
0310S 5 0 0 0 0 30
800
ASP- 27 14 17 19 11 11 0
60 0.1 2900 2S/1.5S/1.5S 52.5 80
0510S 8 3 0 0 0 5
ASP- 31 16 19 22 12 14 18 110 40
90 0.1 2900 2.5S/2S/2S 60
0610S 9 0 5 5 5 5 0 0 0
Note:
Specifications (flow rate, total head) and motor output power (kW) shown above are
20 degree C, degassed to the level of approx. 2mg/L. Such specifications and motor
depending on viscosity, specific gravity and required level of degassing of the actua
for details.
Specifications stated here may be subject to change without notice due to product i
