IDPT
Well Engineering Module
Wellheads
Wellheads
• Drive (or drill & run) 30” Conductor Pipe.
Bell
Bell Nipple
Nipple (( Fill-up
Fill-up Line,
Line, Flow
Flow Line)
Line)
30”
30” Conductor
Conductor Pipe
Pipe
Wellheads
• Drill 26” hole & Run 20” Casing.
21
21 ¼”
¼” BOP
BOP
Drilling
Drilling Spool
Spool
21
21 ¼
¼ ”” Braden
Braden Head
Head
20”
20” Casing
Casing
Wellheads
• Drill 17 1/2” Hole
& Run 13 3/8”
Casing
13
13 5/8”
5/8” BOP
BOP
Drilling
Drilling Spool
Spool
13
13 5/8
5/8 ““ Casing
Casing Spool
Spool
Wellheads
• Drill 12 1/4”
Hole & Run
9 5/8”
Casing: 13 13 5/8”
5/8” BOP
BOP
Drilling
Drilling Spool
Spool
11“
11“ Casing
Casing Spool
Spool
13
13 5/8
5/8 ““ Casing
Casing Spool
Spool
Wellheads
• Drill 8
1/2” Hole
& Run 7” 13
13 5/8”
5/8” BOP
BOP
Liner
Drilling
Drilling Spool
Spool
11
11 ““ Casing
Casing Spool
Spool
13
13 5/8
5/8 ““ Casing
Casing Spool
Spool
Wellheads
• Drill 8
1/2” Hole
& Run 7” 13
13 5/8”
5/8” BOP
BOP
Casing.
Tubing
Tubing Spool
Spool
11
11 ““ Casing
Casing Spool
Spool
13
13 5/8
5/8 ““ Casing
Casing Spool
Spool
Wellheads
Xmas
Xmas Tree
Tree
• Tubing Spool &
Christmas Tree
77 1/16”
1/16” Tubing
Tubing Spool
Spool
11
11 ““ Casing
Casing Spool
Spool
13
13 5/8
5/8 ““ Casing
Casing Spool
Spool
IDPT
Well Engineering Module
Fishing
Fishing Tools
• Outside catch
• Inside catch
• Washover and basket tools
• Fishing for Wireline
• Milling, drilling and smashing
junk
Bowen series 70 overshot
Main characteristics;
Grip increases as pull increases
Grip increases with LH torque
Grip releases with RH torque
Very strong in tension, can jar on
Allows circulation and wireline tools to go
inside the fish
Can be released downhole without
damaging the fish
Can mill over light damage
The Tool Of First Choice!
Die Collar
• Main characteristics;
• Weak in tension, cannot jar on
• Allows circulation and Wireline tools to go inside the fish
• Cannot be released downhole so requires a Safety Joint and
is rarely used.
Releasing Spear
• An overshot in reverse.
• Main characteristics;
• Grip increases as pull increases
• Grip releases with RH torque
• Not so strong in tension, can lightly jar
on
• Allows circulation through the fish
• Can be released downhole without
damaging the fish
Taper Tap
• A die collar in reverse.
• Main characteristics;
• Weak in tension, cannot jar on
• Allows circulation through the
fish
• Cannot be released downhole so
requires a Safety Joint
• Rarely used.
Jet Junk Retriever
• Main characteristics;
• A ball is dropped which diverts the fluid
flow around and up inside the tool.
• Spring loaded fingers allow the junk in
but not out.
• Ideal for drill bit cones.
• No indication of catching the fish until at
surface.
Junk Basket
• Main characteristics;
• Run above the drill bit
(pin up, box down).
• Can catch small pieces
of junk, like broken teeth.
• Sometimes run before a
PDC or diamond bit.
Poorboy Finger Basket
• Main characteristics;
• Can be made by a good rig
welder from a piece of liner!
• Set on bottom with low weight
and rotated slowly. Fingers twist
closed below the junk.
• Ideal for drill bit cones.
• No indication of catching the
fish until at surface.
Fishing Magnet
• Main characteristics;
• Can be a permanent magnet on
drillpipe or an electro magnet on
Wireline.
• Ideal for small bits of ferrous junk.
• No indication of catching the fish
until at surface.
Fishing for Wireline
3 different situations;
Wire has parted from the tool at the weak point
Wire has parted somewhere else
Wire is intact
If no wire in the hole, use an outside catch tool.
If wire is in the hole, it’s a horrible job to get it out!!
Wireline in the hole on top of the tool
The only choice is a Wireline Spear.
Main characteristics;
Run on drillpipe into the Wireline
“birds nest”.
Rotated a little and pick up.
Once the spear is at surface, the wire
is cut and retrieved.
Various Mill Configurations
Milling Tools
Washover Shoes, Safety Joint, Bumper Jar
Fishing Bumper Jar
Washover Safety Joint
