Service Manual

Change for Life

Service Manual
Models: GPC12AL-K3NNA1A
GPH12AL-K3NNA1A
GPH12AL-K3NNA2A
GPH12AL-K3NNA3A
(Refrigerant R410A)

GREE ELECTRIC APPLIANCES,INC.OF ZHUHAI

 Service Manual

Table of Contents

Part Ⅰ : Technical Information............................................................. 1

1. Summary..................................................................................................... 1
2. Specifications........................................................................................... 3
3. Outline Dimension Diagram.............................................................. 5
4. Refrigerant System Diagram............................................................ 8
5. Electrical Part........................................................................................... 9
5.1 Wiring Diagram............................................................................................ 9
5.2 PCB Printed Diagram................................................................................. 11
6. Function and Control.......................................................................... 13
6.1 Introduction of control panel....................................................................... 13
6.2 Remote Controller Introduction.................................................................. 14

Part Ⅱ : Installation and Maintenance .......................................... 20

7. Notes for Installation and Maintenance.................................... 20
8. Install........................................................................................................... 23
8.1 Install Wire Hook........................................................................................ 23
8.2 Removing Collected Water........................................................................ 23
8.3 Installation and Disassembly of heat Discharge Pipe................................ 25
8.4 Operation test............................................................................................. 26
9. Maintenance............................................................................................ 27
9.1 Error Code.................................................................................................. 27
9.2 Malfunction Detection Flowchart................................................................ 29
9.3 Maintenance Method for Common Malfunction......................................... 35
10. Exploded View and Parts List..................................................... 37
11. Removal Procedure........................................................................... 49

Appendix:....................................................................................................... 57
Appendix 1: Reference Sheet of Celsius and Fahrenheit................................ 57
Appendix 2: List of Resistance for Temperature Sensor.................................. 58
Appendix 3: Resistance Value Table of Humidity Sensor................................ 61

Table of Contents
Service Manual

Part Ⅰ : Technical Information

1. Summary

Models:GPC12AL-K3NNA1A
GPH12AL-K3NNA1A

Model: GPH12AL-K3NNA2A

Technical Information 1
 Service Manual

Model: GPH12AL-K3NNA3A

Remote Controller:

YB1F2(XFAN)

FAN AUTO
OPER
AIR HEALTH X-FAN
HUMIDITY
FILTER
TURBO
HOUR
ON/OFF

ON/OFF MODE

FAN

X-FAN TEMP TIMER

TURBO SLEEP LIGHT

2 Technical Information
Service Manual

2. Specifications
Parameter Unit Value
GPH12AL-K3NNA1A
Model GPC12AL-K3NNA1A GPH12AL-K3NNA2A
GPH12AL-K3NNA3A
CK010024500
CK010025700
Product Code CK010025800
CK010025702
CK010025900
Rated Voltage V～ 220-240 220-240
Power Rated Frequency Hz 50 50
Supply
Phases 1 1
Cooling Capacity W 3520 3520
Heating Capacity W / 3520
Cooling Power Input W 1345 1345
Heating Power Input W / 1235
Cooling Power Current A 6.0 6.0
Heating Power Current A / 5.5
Rated Input W 1550 1550
Rated Current A 7.0 7.0
3
Air Flow Volume(H/M/L) m /h 360/330/300 360/330/300
Dehumidifying Volume L/h 1.6 1.6
EER W/W 2.61 2.61
COP W/W / 2.85
SEER / /
HSPF / /
2
Application Area m 15-22 15-22
Climate Type T1 T1
Isolation I I
Moisture Protection IPX0 IPX0
Permissible Excessive Operating Pressure for
MPa 4.3 4.3
the Discharge Side
Permissible Excessive Operating Pressure for
MPa 2.5 2.5
the Suction Side
Throttling Method Capillary Capillary
Defrosting Method / Automatic Defrosting
Fuse A 3.15 3.15
o
Operation Temp C 16~30 16~30
o
Ambient Temp (Cooling) C 16~35 16~35
o
Ambient Temp (Heating) C / 10~27
Sound Pressure Level (H/M/L) dB (A) 53/51/49 53/51/49
Sound Power Level (H/M/L) dB (A) 65/64/63 65/64/63
Dimension (WXHXD) mm 390X820X405 390X820X405
Dimension of Carton Box (LXWXH) mm 578X452X847 578X452X847
Dimension of Package (LXWXH) mm 581X455X862 581X455X862
Net Weight kg 39 39
Gross Weight kg 44 44
Refrigerant R410A R410A
Refrigerant Charge kg 0.79 0.81

Technical Information 3
 Service Manual

ZHUHAI LANDA COMPRESSOR ZHUHAI LANDA COMPRESSOR

Compressor Manufacturer/Trademark
CO., LTD CO., LTD
Compressor Model QXA-C136B030B QXA-C136B030B
Compressor Oil POE(RB68EP) POE(RB68EP)
Compressor Compressor Type Rotary Rotary
L.R.A. A 27.00 27.00
Compressor RLA A 5.1 5.1
Compressor Power Input W 1115 1115
Overload Protector UP3-02 UP3-02
Fan Type Centrifugal Centrifugal
Diameter Length(DXL) mm Φ187.6X108.2 Φ187.6X108.2
Fan Motor Speed(H/M/L) r/min 1050/960/870 1050/960/870
Output of Fan Motor W 16 16
Fan Motor RLA A 0.3 0.3
Fan Motor Capacitor μF 3.5 3.5
Evaporator
Form Aluminum Fin-copper Tube Aluminum Fin-copper Tube
Pipe Diameter mm Φ7 Φ7
Row-fin Gap mm 3-1.4 3-1.4
Coil Length (LXDXW) mm 442X38.1X228.6 442X38.1X228.6
Swing Motor Model / /
Output of Swing Motor W / /
Fan Type Centrifugal Centrifugal
Fan Diameter mm Φ224.5X80 Φ224.5X80
Form Aluminum Fin-copper Tube Aluminum Fin-copper Tube
Pipe Diameter mm Φ7 Φ7
Rows-fin Gap mm 3-1.4 3-1.4
Condenser
Coil Length (LXDXW) mm 592X34.2X304.8/475X11.4X266.7 592X34.2X304.8/475X11.4X266.7
Fan Motor Speed rpm 1040/850 1040/850
Output of Fan Motor W 50 50
Fan Motor RLA A 0.53 0.53
Fan Motor Capacitor μF 3.5 3.5

The above data is subject to change without notice. Please refer to the nameplate of the unit.

4 Technical Information
Service Manual

3. Outline Dimension Diagram

GPC12AL-K3NNA1A GPH12AL-K3NNA1A

390

405

820

1:1
Unit:mm

Technical Information 5
 Service Manual

GPH12AL-K3NNA2A

390

405

820

Unit:mm

6 Technical Information
Service Manual

GPH12AL-K3NNA3A

390

405

820

Unit:mm

Technical Information 7
 Service Manual

4. Refrigerant System Diagram

GPC12AL-K3NNA1A

CENTRIFUGAL FAN CENTRIFUGAL FAN

COOLED AIR HOT DISCHARGED AIR

COMPRESSOR

INDOOR COILS OUTDOOR COILS

CAPILLARY

REFRIGERANT FLOW DIRECTION

GPH12AL-K3NNA1A GPH12AL-K3NNA2A GPH12AL-K3NNA3A

4-Way valve
COOLED AIR
CENTRIFUGAL FAN CENTRIFUGAL FAN HOT DISCHARGED AIR

HOT AIR COOLED AIR

COMPRESSOR

INDOOR COILS

OUTDOOR COILS

CAPILLARY

NOTES: COOLING MODE

REFRIGERANT FLOW DIRECTION HEATING MODE

8 Technical Information
Service Manual

5. Electrical Part
5.1 Wiring Diagram
●Instruction

Symbol Symbol Color Symbol Symbol Color Symbol Name

WH White GN Green COMP Compressor
YE Yellow BN Brown Grounding wire
RD Red BU Blue / /
YEGN Yellow/Green BK Black / /
VT Violet OG Orange / /

●Electric Diagram

Model:GPC12AL-K3NNA1A

ROOM TEMP. TUBE TEMP.OUTTUBE TEMP.RECEIVER

SENSOR SENSOR SENSOR BOARD COLD PLASMA
GENERATOR POWER
AP3 BN(BK)
RT1 RT2 RT3 L
BU RD BU(WH)
DISPLAY N
BOARD YEGN(GN)
AP2 HEALTH-NHEALTH-L
PE
DISP2 ROOM TUBE OUTTUBE REC
DISP2
N3 BU

DISP1
DISP1 AP1 AC-L

MAIN BOARD K201 COMP.

C YEGN
YEGN M3 N1 COMP
BU COMP R(M) S
WATER1
RD PE
PE WATER HIGH-WP OFAN FAN
MOTOR
RD CAP. YE

WH BK
RD C1
NC COM
SA M2 M1
YEGN YEGN
WATER LEVEL DOWN FAN UP FAN
SWITCH MOTOR MOTOR

PE RD CAP. BN PE RD CAP. BN
C3 C2
60000700008501

Technical Information 9
 Service Manual

Models:GPH12AL-K3NNA1A GPH12AL-K3NNA2A GPH12AL-K3NNA3A

ROOM TEMP.TUBE TEMP.OUTTUBE TEMP.

WATER MOTOR SENSOR SENSOR SENSOR RECEIVER COLD PLASMA
GENERATOR POWER
YEGN M3 BOARD BN(BK)
RT1 RT2 RT3 L
AP3 BU RD BU(WH)
N
PE RD BU YEGN(GN)
HEALTH-NHEALTH-L
PE
N1 ROOM TUBE OUTTUBE REC
WATER
N3 BU
DISP2
DISP2 AP1 AC-L

MAIN BOARD K201 COMP.

C YEGN
DISP1 COMP
DISP1 COMP R(M) S
AP2 HIGH-WP OFAN FAN
N2 4WAY
DISPLAY RD CAP. YE
BOARD
PE
WH BK RD C1
4YV NC COM
4-WAY SA M2 M1 YEGN
YEGN
VALVE WATER LEVEL
SWITCH PE
PE
RD CAP. BN RD CAP. BN

C3 C2
DOWN FAN UP FAN
MOTOR MOTOR
6361000045101

These wiring diagrams are subject to change without notice; please refer to the one supplied with the unit.

10 Technical Information
Service Manual

5.2 PCB Printed Diagram

(1)Silk screen on main board

TOP VIEW

4 5 6 7 8 9 10

NO. NAME
1 Piezoresistor
3 2 Fuse
11
2 3 Copper fin N2 of neutral wire
4 Copper fin N1 of neutral wire
1 5 Copper fin N3 of neutral wire
6 Indoor fan
7 4-way valve terminal
12 8 Neutral wire terminal
13 9 Outdoor fan
10 Copper fin water of motor
14 11 Copper fin Health of live wire
15 12 Tube temperature sensor
13 Ambient temperature sensor
14 Outtube temperature sensor
15 Interface of remoter
16 16 High water level
17 Interface of display board
18 Interface of wifi board

17

18
BOTTOM VIEW

Technical Information 11
 Service Manual

(2)Silk screen on display board

TOP VIEW

Interface of
main board

BOTTOM VIEW

12 Technical Information
Service Manual

6. Function and Control

6.1 Introduction of control panel
Dual-8 nixie tube
+ / - button Cool mode indicator
Health indicator(Optional)
Dry mode indicator

Fan mode indicator

Heat mode indicator

Cool&Heat Unit only
Fan speed indicator
Sleep button Mode button

Fan button Timer button

ON/OFF button
Operation of control panel
Note:
●After putting through the power, the air conditioner will give out a sound. After that, you can operate the air conditioner by the control
panel.
● Under ON status, after each pressing of the button on control panel, the air conditioner will give out a sound. Meanwhile, corresponding
indicator on control panel will be bright.
● Under OFF status, dual-8 nixie tube on control panel wont display.
Under ON status, dual-8 nixie tube on control panel will display set temperature.
under cooling mode, while it wont display under other modes

1. ON/OFF button
Press this button to turn on or turn off air conditioner.
2. + / - button
Under cooling mode, press “+” or “-” button to increase or decrease set temperature by1°C(°F). Set temperature range is
16°C(61°F)~30°C(86°F). Under auto, drying or fan mode, this button is invalid.
3. Mode button
Press this button and the mode will circulate according to below sequence:
COOL→DRY→FAN
COOL: Under this mode, cooling mode indicator is bright. Dual-8 nixie tube displays set temperature. Temperature setting range
is16°C~30°C.
DRY: Under this mode, drying mode indicator is bright. Dual-8 nixie tube wont display.
FAN: Under this mode, air conditioner operates at set fan speed. Fan indicator and corresponding speed indicator is ON. Dual-8 nixie
tube wont display.(Note: You must connect the heat-discharge pipe before operating cooling or drying mode. No need for only fan mode.)
Heat Cool&Heat Unit only : Under this mode, heating mode indicator is bright.
Dual-8 nixie tube displays set temperature.
Temperature setting range is 16°C~30°C.
4. FAN button
Press this button and the fan speed will circulate as “low speed→medium speed →high speed→auto fan→low speed”.
5. Timer button
Press timer button to enter into timer setting mode. Under this mode, press " + " or " - " button to adjust the timer setting. Timer setting
will increase or decrease 0.5 hour by pressing " + " or " - " button within 10 hours, while timer setting will increase or decrease 1 hour by
pressing " + " or " - " button beyond 10 hours.After timer setting is finished, the unit will display temperature if theres no operation for
5s. If timer function is started up, the upper indicator will keep the display status. Others, it wont be displayed. Under timer mode, press
timer button again to cancel timer mode.
6. Sleep
● Press sleep button to enter into sleep mode. If the controller operates at cooling mode, after sleep mode is started up, preset
temperature will increase by 1°C within 1 hour ;preset temperature will increase by 2°C within 2 hours and then the unit will operate at
this temperature all the time;
● Press sleep button to enter into sleep mode. If the controller operates at heating mode, after sleep mode is started up, preset
temperature will decrease by 1°C within 1 hour ;preset temperature will decrease by 2°C within 2 hours and then the unit will operate at
this temperature all the time;
● Sleep function is not available for fan mode, drying mode. If sleep function is started up, the upper indicator will keep the display status.
Others, it wont be displayed.

Technical Information 13
 Service Manual

6.2 Remote Controller Introduction

Buttons on Remote Controller
1 ON/OFF button
FAN AUTO
OPER
AIR HEALTH X-FAN 2 MODE button
HUMIDITY
FILTER 3 +/- button
TURBO
HOUR
4 FAN button
ON/OFF

5 button(Not applicable for this unit)

1 2 6 button(Not applicable for this unit)

ON/OFF MODE
7 HEALTH SAVE button
3
8 X-FAN button
4 5 (Note: X-FAN is same with BLOW)

FAN 9 TEMP button

7 6
8 10 TIMER button
10
9
X-FAN TEMP TIMER 11 TURBO button
TURBO SLEEP LIGHT (Not applicable for this unit)
11 13
12 SLEEP button
12
13 LIGHT button

Icon Display on Remote Controller

set fan speed
air mode FAN AUTO send signal
OPER
Operation mode health mode
AIR HEALTH X-FAN
Auto mode X-fan
HUMIDITY
Cool mode
Dry mode FILTER set temperature
Fan mode TURBO turbo mode
Heat mode HOUR (Not applicable for this unit)
Cool&Heat Unit only ON/OFF TIMER ON/TIMER OFF
set time
Child Lock left & right swing
(Not applicable for this unit)
Sleep mode
Temp. display type light Up & down swing
:Set temp. (Not applicable for this unit)
:Indoor ambient temp.
:Outdoor ambient temp.
(Not applicable for this unit)

14 Technical Information
Service Manual

1.ON/DFF button
Press this button can turn on or turn off the air conditioner. After turning on the unit,operation indicator " " on the unit is ON (green
indicator. Color may be differ-ent for different models) and the unit gives out a sound.
2.MODE button
Press this button can select your required operation mode.
AUTO COOL DRY FAN HEAT

● After selecting auto mode, air conditioner will operate automatically according to ambient temperature. Set temperature cant be
adjusted and also cant be displa- yed. Press "FAN" button can adjust fan speed.
● After selecting cool mode, air conditioner operates under cool mode. Cool indicator " " on the unit is ON. You can press "+" or "-"
button to adjust set temperature. Press "FAN" button can adjust fan speed.
● After selecting dry mode, air conditioner operates under dry mode at low speed. Dry indicator " " on the unit is ON. Under dry mode,
fan speed cant be ad- justed.
● After selecting fan mode, air conditioner operates only under fan mode, All mode indicators on the unit is OFF. Operation indicator is
ON. Press "FAN" button can adjust fan speed.
● After selecting heat mode, air conditioner operates under heat mode. Heat indicator " " on the unit is ON. You can press "+" or "-"
button to adjust set temperature.
Press "FAN" button to adjust fan speed.
(Cool&Heat Unit only)

Note:
For preventing cold wind, after starting up heating mode, indoor fan will blow fanafterdelaying 1-5min. (Details time is decided by indoor
ambient temperature)Temperature setting range on remote controller: 16℃ -30℃ . Fan speed setting range: auto, low speed, medium
speed and high speed.

3."+"or"-"button
● After each pressing of "+" or "-" button, it can increase or decrease set temperature 1℃ . Hold "+" or "-" button, 2s later, set temperature
on remote controller will change quickly. After reaching to your required time, loosen the button. Temperature indicator on the unit will
also change accordingly. (Temperature cant be adjusted under auto mode)

5. button(Not applicable for this unit)

6. button(Not applicable for this unit)

7.HEALTH SAVE button

HEALTH FUNCTION:
After pressing HEALTH button, remote controller will switch circularly as below:"HEALTH"→"AIR"→"AIR HEALTH"→"no display"
● When selecting "HEALTH" by remote controller, HEALTH function will be started up.
● When selecting "AIR" by remote controller, AIR function will be started up. (Not applicable for this unit)
● When selecting "AIT HEALTH", AIR and HEALTH function will be started up.
● When theres no display on remote controller, AIR and HEALTH function will be turned off.

8.X-FAN button
After pressing this button under cooling or dry mode, remote controller displays the character of "X-FAN" and X-FAN function is started
up. Press this button again to cancel X-FAN function. The character of "X-FAN" will disappear.
Note:
● After starting up X-FAN function, when turning off the unit, indoor fan will continue to operate for a while at low speed to dry the
residual water inside the the unit.
● When the unit operates under X-FAN mode, press "X-FAN" button can turn off X-FAN function. Indoor fan stops operation immediately.

Technical Information 15
 Service Manual
9.TEMP button
Press this button can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on the units display.
Temperature is set circularly by remote controller as below:
no display

● When selecting " " by remote controller or no display, temperature indicator on the unit displays set temperature.
● When selecting " " by remote controller, temperature indicator on the unit displays indoor ambient temperature.
● When selecting " " by remote controller, temperature indicator on the unit displays outdoor ambient temperature.
Note:
● Outdoor ambient temperature display may cant be selected for some models.
When the unit receives " " signal, it displays indoor set temperature.
● Only for the model whose the unit has dual-8 display.
10.TIMER button
● At ON status, press this button once can set TIMER OFF. The character of HOUR and OFF will flash.Press"+"or"-"button within 5s
can adjust the time ofTIMER ON. After each pressing of "+" or "-" button, time will increase or decrease half an hour. When holding "+"
or "-" button, 2s later, the time will change quickly until to reach to your required time.After that,press"TIMER"button to confirm it.The
character of HOUR and OFF wont flash again.
Cancel TIMER OFF: Press "TIMER" button again under TIMER OFF status.● At OFF status, press this button once can set TIMER
ON. Please refer to TIMER off for detailed operation.
Cancel TIMER ON: Press "TIMER" button again under TIMER ON status.

Time interval between two operations cant exceed 5s. Otherwise, remote controller will exit the setting status automatically.
11.TURBO button (Not applicable for this unit)
When pressing this button under cooling or heating mode, air conditioner will enter into quick cooling or quick heating mode. The
character of "TURBO" is displayed on remote controller. Press this button again to exit turbo function and the character of "TURBO"
will be disappeared on remote controller.
12.SLEEP button
Press this button under cooling, heating mode can start up sleep function." " icon will be displayed on remote controller. Press this
button again to cancel sleep function. " "icon on remote controller will be displayed.
13.LIGHT button
Press this button can turn off the light for the units display. " " icon on remotecontroller will disappear. Press this button again to turn
on the light for the units display. " " icon on remote controller will be displayed.

Function introduction for combination buttons

Child lock function
Press "+" and "-" buttons simultaneously can turn on or turn off child lock function. When child lock function is started up, " " icon will
be displayed on remote controller.If operate remote controller," "icon will flash three times,while remote controller wont send signal.

Switchover function for temperature display

After turning off the unit by remote controller, press "-" button and "MODE" buttonsimultaneously to switch between ℃ and °F .

signal sender battery

reinstall

remove

Cover of battery box

16 Technical Information
Service Manual

NOTICE:
● During operation, point the remote control signal sender at the receiving window on the unit.
● The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between
them.
● Signal may be interfered easily in the room where there is fluorescent lamp or wireless telephone; remote controller should be close to
the unit during operation.
● Replace new batteries of the same model when replacement is required.
● When you dont use remote controller for a long time, please take out the batteries.
● If the display on remote controller is fuzzy or theres no display, please replace batteries.

Technical Information 17
 Service Manual

6.3 Introduction of Basic Mode Function

1. Temperature Parameter

◆ Indo or setting temperature (Tpreset)

◆ Indoor ambient temperature (Tamb.)

2. Basic Functions of System
After the unit is energized, the interval of start-up time for compressor is no less than 3min under any conditions; when the compressor is
started, the unit is off without the temperature change in 6min.
2.1 Cool Mode
2.1.1 Working conditions and process of cooling
a) When Tabm.≥Tpreset + 1oC (2oF), the unit will start to run in cooling mode, the compressor and kick motor start to run, and fan motor
runs under preset fan speed.
b) When Tabm.≤ Tpreset - 1oC (2oF), the compressor and kick motor stop to run, and fan motor runs under preset fan speed.
c) When Tpreset - 1oC (2oF)<Tamb.<Tpreset + 1oC (2oF), the unit will keep the current running status.Under this mode, the temperature
setting range is 61oF-86oF (16oC -30oC ).
Tamb. Start cooling
Tpreset +1 ˚C
Original operating status

Tpreset –1 ˚C
Stop cooling
≥ 6 min. ≥ 3 min. ≥ 6 min.

Compressor

Outdoor fan

Indoor fan Setting fan speed

Run Stop

a) Under cooling mode, after 1h of setting sleep process, Tpreset increases 2oF(1oC); 2h later, Tpreset increases 4oF(2oC). After 2h, the
setting temperature never increases, but the upper limit of increased setting temperature is 86oF(30oC)
b) Under heating mode, after 1h of setting sleep process, Tpreset decreases 2oF(1oC); 2h later, Tpreset decreases 4oF(2oC). After 2h, the
setting temperature never decreases, but the upper limit of decreased setting temperature is 61oF(16oC)
c) There is no sleep function under fan and dry mode.
d) When set sleep function, shift mode will cancel sleep function.
e) The setting temperature display is the same with remote controller; it is not influenced by the setting temperature increases/ decreases.
2.2 Heating mode
When Tamb. ≤Tpreset+3°C(6°F), the unit operates in heating mode. Meanwhile, 4-way valve, compressor operates, and indoor fan
operates at cold air prevention condition;
When Tpreset+3°C(6°F)<Tamb.<Tpreset+5°C(10°F), the unit keeps original operation status,
When Tamb.≥Tpreset+5°C(10°F), compressor stop operation simultaneously. 4-way valve stop operation after the compressor has
stopped for 2 minutes. Indoor fan operates at blowing residual heat conditioner.
Under this mode, the temperature setting range is 16-30°C(61-86°F).
3.3 Auto Fan
a) Auto fan speed under Cooling mode;
Tamb≥Tpreset+4oF(2oC) High fan;
Tpreset<Tamb.< Tpreset+4oF(2oC) Med fan;
Tamb≤Tpreset Low fan;
b) There is 3.5min delay for auto fan shift.
3.4 TIMER Function
● General timer
a) TIMER ON: It can set timer on when the system is off, the setting time range is 0.5h-24h, when the time of setting timer on reaches, and
the system runs with the previous setting mode.
b) TIMER OFF: It can set timer on when the system is on, the setting time range is 0.5h-24h, when the time of setting timer off reaches,
the system stop to work.
● Clock timer
a) TIMER ON: If set timer on when the system is running, it continues to run; if set timer on when the system is off, when the time of setting
timer on reaches, and the system runs with the previous setting mode.
b) TIMER OFF: If set timer off when the system is off, the system keeps the stand-by status when setting timer off; if set timer off when the
system is on, when the time of timer off reaches, the system stops to run.
3.5 Memory Function
The system memories the setting running status of previous power-off, and runs automatically with the setting running status before it
power-off when it is energized again. If the unit is on before power-off, the compressor will 3min delay protection when it is energized
again.
3.6 Indicator Lamp, dual-8 digital pipe
a) When the unit runs, under cooling mode, cooling indicator lamp lights, dual-8 displays preset temperature.
b) When the unit runs, under fan mode, fan indicator lamp lights, dual-8 does not display.
c) When the unit runs, under dry mode, dry indicator lamp lights, dual-8 does not display.
d) When the unit runs, under heating mode, heating indicator lamp lights, dual-8 displays preset temperature.

18 Technical Information
Service Manual

3.7 Setting button function

a) ON/OFF button: It controls systems switch.
b) Mode button: Mode setting cycle with below sequence: Cooling only unit: cooling-> dry-> fan.
c) Temp. ▼ button: Set temperature when the unit is on, the setting temperature decreases 1oC or oF per press
Temp. ▼ button; it will never setting when the setting reaches to 16oC or 61oF. The button is not valid under auto, dry and fan mode.
d) Temp. ▲ button: Set temperature when the unit is on, the setting temperature increases 1oC or oF per press
Temp. ▲ button; it will never setting when the setting reaches to 30oC or 86oF. The button is not valid under auto, dry and fan mode.
3.8 Light Control
If set the light is on with remote control, the indicator lamp and dual-8 display the current setting status; if set the
light is off with remote control, turn off the lamp immediately. If there is front panel button or remote control button
operation when setting light off with remote control, the indicator lamp and dual-8 display current setting status,
and turn off the light 5S later. Remote control light button does not controlled by failure display.
3.9 Protection Function
● Anti-freeze Protection
When the anti-freeze protection is inspected, the compressor stops, fan motor runs with setting fan speed.
When the anti-freeze protection is canceled and reaches to the 3min time-delay, it runs with the original status.
Temperature sensor failure inspection
a) Environment temperature sensor is open, short circuit: dual-8 displays F1, the cooling indicator lamp goes out 3S and blinks 1
time, and it will light up 0.5S and go out 0.5S when it is blinking.
b) Indoor pipe temperature sensor is open, short circuit: dual-8 displays F2, the cooling indicator lamp goes out 3S and blinks 2
times, and it will light up 0.5S and go out 0.5S when it is blinking.
c) Outdoor pipe temperature sensor is open, short circuit: dual-8 displays F4, the cooling indicator lamp goes out 3S and blinks 4
times, and it will light up 0.5S and go out 0.5S when it is blinking.
d) The compressor or electric heating pipe stops when the temperature sensor failure and the unit is on, The fan motor will be deal
regarding compressor or electric pipe reach to the temperature point and stops.
● Over current Protection
If the system current is inspected too large for 3min continuously, the fan motor runs with setting conditions, other load stops; 3min
later, the unit runs with the previously status; if over current protection occurs for 6 times continuously, display error code “E5”, the
load stops this time; if block the button except ON/OFF button, it will remote control the unit to off then on, or turn off with button, or
re-energized; the time of over current protection will zero clearing with remote control, press to turn on or re-energized.
● Over-flow Protection
If the over-flow is detected for 3S, it will enter into over-flow protection. Display error code H8, heating indicator lamp or over-flow
indicator lamp goes out 3S and blinks 8 times.

Technical Information 19
 Service Manual

Part Ⅱ : Installation and Maintenance

7. Notes for Installation and Maintenance
Safety Precautions:
Important! 10. Check if there is electric leakage on the unit body. If yes,
Please read the safety precautions carefully before please eliminate the electric leakage.
installation and maintenance. 11. Replace the fuse with a new one of the same specification
The following contents are very important for installation if it is burnt down; dont replace it with a cooper wire or
and maintenance. conducting wire.
Please follow the instructions below. 12. If the unit is to be installed in a humid place, the circuit
●The installation or maintenance must accord with the breaker must be installed.
instructions.
●Comply with all national electrical codes and local Refrigerant Safety Precautions:
electrical codes.
●Pay attention to the warnings and cautions in this manual. 1. Avoid contact between refrigerant and fire as it generates
●All installation and maintenance shall be performed by poisonous gas. Recycle the refrigerant inside the unit
distributor or qualified person. completely before welding pipes.
●All electric work must be performed by a licensed 2. Apply specified refrigerant only. Never have it mixed
technician according to local regulations and the with any other refrigerant. Never have air remain in the
instructions given in this manual. refrigerant line as it may lead to rupture or other hazards.
●Be caution during installation and maintenance. Prohibit 3.If refrigerant is leaking seriously, it may cause suffocation
incorrect operation to prevent electric shock, casualty and or explosion. When using the combustible refrigerant,
other accidents. please put the unit at ventilated place.
4. Never touch the refrigerant piping or compressor without
wearing glove to avoid scald or frostbite.

Warnings Improper installation may lead to fire hazard explosion,

electric shock or injury.

Electrical Safety Precautions:

1. Cut off the power supply of air conditioner before

checking and maintenance.
2. The air conditioner should be installed in suitable
location and ensure the power plug is touchable.
3. Make sure each wiring terminal is connected firmly
during installation and maintenance.
4. Have the unit adequately grounded. The grounding
wire cant be used for other purposes.
5. Must apply protective accessories such as protective
boards, cable-cross loop and wire clip.
6. The live wire, neutral wire and grounding wire of
power supply must be corresponding to the live wire,
neutral wire and grounding wire of the air conditioner.
7. The power cord and power connection wires cant be
pressed by hard objects.
8. If power cord or connection wire is broken, it must be
replaced by a qualified person.
9. For the air conditioner without plug, an air switch
must be installed in the circuit. The air switch should be
all-pole parting and the contact parting distance should
be more than 3mm.

20 Maintenance
 Service Manual

Main Tools for Installation and Maintenance

1. Level meter, measuring tape 2.Screw driver 3.Scissors, saw

4.Electroprobe 5. Universal meter 6.Torque wrench, open-end wrench, inner

hexagon spanner

7. Electronic leakage detector 8. Vacuum pump 9. Pressure meter

10. Pipe pliers, pipe cutter 11. Pipe expander, pipe bender 12. Soldering appliance, refrigerant container

R410A

Maintenance 21
 Service Manual

Installation procedures
Start installation

Preparation before installation

Read the requirements Prepare tools

for electric connection

Install wire hook

Install drainage pipe

Install window frame

Install heat discharge pipe and joint

pack up heat discharge pipe

Check after installation and test operation

Finish installation

Note: this flow is only for reference; please find the more detailed installation steps in this section.

Preparation before Installation

Note:check if the accessories are available before installation

Accessory list

joint A heat discharge pipe joint B joint C

wire hook (2) screw(3) pipe clip rubber plug pipe hoop (2)

battery (2)
Drain connector (1) drainage pipe remote controller (AAA 1.5V) user's manual (2)

22 Maintenance
 Service Manual

8. Install
8.1 Install Wire Hook
● Assemble the wire hook at the back of the unit with screws.(As show in Fig.1)

direction of wire hook is upward

wire hook

screw

direction of wire hook is downward

Fig.1 Fig.2

● Wind the power cord around the wire hook.(As show in Fig.2)

8.2 Removing Collected Water

There are 2 ways to remove collected water:
1. Use the continuous drainage option from the lower hole.
NOTICE:When using the continuous drainage option from the bottom hole, install drainage pipe as follow before using, otherwise poor
drainage will affect normal operation of the unit.
● Instructions for drainage pipe installation.
(1) Fix the drainage pipe clip on the right of rear side plate near
drainage port with a screw.(As show in Fig.3)
(2) Remove the rubber plug at drainage port.(As show in Fig.4)
(3) Put the drainage pipe into drainage port and screw it up, and
then bind it with pipe hoop.
(4) Put the rubber plug into the other side of drainage pipe, fix it
drainage pipe clip
with pipe hoop and then fix it in the drainage pipe clip.(As show in drainage port
Fig.5) screw
pipe hoop
rubber plug Fig.3

drainage pipe clip

drainage pipe

pipe hoop
drainage port
drainage port
Fig.5
Fig.4

Maintenance 23
 Service Manual

● Drainage way as follows.

1. In Cool, Dry or Heat mode operating, the condensation water will be drained to the chassis.(As show in Fig.6)
2. When the chassis is full with water, the buzzer will give out 8 sounds and "H8" is displayed to remind user to discharge water:
● Move the unit to a suitable place for discharging water; do not tilt the unit and keep it horizontal during moving;
● Take the drainage pipe from the clip and pull out the rubber plug on the drainage pipe to discharge water;
● Put back the rubber plug onto drainage pipe after finishing dischargeing and then fix the pipe on the clip;
● After full water protection is eliminated and the compressor has been stopped for 3 minutes, the unit will resume operation.
2.Use the continuous drainage option from the middle hole
NOTICE:Water can be automatically emptied into a floor drain by attaching 14mm inner diameter hose (not included).
(1) Remove the continuous drain cap 1 by turning it counter clockwise then remove the rubber stopper 2 from the spout. (As show
in Fig.7)

Fig.6 Fig.7

(2) Screw the drain connector to(included in the package) the spout by turning clockwise.(As show in Fig.8)
(3) Insert the drainage hose into drain connector.(As show in Fig.9)

Fig.8
Fig.9
ATTENTION:
When using continuous drainage option from the middle hole, place portable on a level surface and make sure garden hose is clear
of any obstructions and is directed downward. Placing portable on an uneven surface or improper hose installation may result in
water filling up the chassis and causing the unit to shut off. Empty water in the chassis if shut off occurs, then check portable location
and hose for proper setup.

24 Maintenance
 Service Manual

8.3 Installation and Disassembly of heat Discharge Pipe

A. Install heat discharge pipe
clockwise
(1) Rotate joint A and joint B clockwise into the two ends of heat discharge clockwise
pipe.(As show in Fig.10)
(2) Insert joint A of heat discharge pipe (the side with "TOP" is upwards) into joint A
the groove until you hear a sound.(As shown in Fig.11)
(3) Lead the exhaust hose outdoors.(As shown in Fig.12)
joint B+C
heat discharge pipe

Fig.10
clasp the side with "TOP" is upwards

groove Fig.12
Fig.11

Note of Install heat discharge pipe

In order to improve cooling efficiency, the heat discharge pipe should be as short as possible and flat without curve to ensure smooth
heat discharge.(As shown in Fig.13)
●The length of the heat discharge pipe is less than 1m. It is recommended to use it with shortest length.
●The length of the heat discharge pipe is less than 1m. It is recommended to use it with shortest length.(As shown in Fig.14)

correct correct

correct

wrong

Fig.13 Fig.14

●Correct installation is as shown in figure (When installing it on wall, height of hall should be about 40cm-130cm from floor).(As shown
in Fig.15)
●Wrong installation is shown in following figure (If the pipe is bent too much, it would easily cause malfunction.(As shown in Fig.16)

Fig.15 Fig.16

Maintenance 25
 Service Manual

B. Disassemble heat discharge pipe

(1) Remove joint B

remove joint B from joint C.(As shown in Fig.17)
(2) Remove joint A: Press the clasp and lift joint A upwards to remove it.(As shown in Fig.18)

clasp
upwards
joint A disassemble

joint B+C
Fig.18
Fig.17

8.4 Operation test

●Put through the power supply and then press ON/OFF button on remote controller to start the unit.
●Press mode button to select auto, cooling, drying, fan or heating function, and then check if the unit operates normally.
●If ambient temperature is below 16°C, the unit cant operate in cooling mode.

26 Maintenance
 Service Manual

9. Maintenance
9.1 Error Code

Display Method of Indoor Unit

Indicator lamp
(During blinking, ON for 0.5S and
NO. Malfunction OFF for 0.5 S)
Error A/C Status Possible Causes
Name Code
Operation COOL HEAT
Inidicato Indicator Indicator

1. The wiring terminal between indoor

ambient temperature sensor and main
Indoor board is loosened or poorly contacted.
Compressor and
ambient 2. Theres short circuit due to trip-over of the
OFF 3S draw water motor
temperature parts on main board.
1 F1 and blinks stop operation. Fan
sensor is
once operates at set fan 3.Indoor ambient temperature sensor is
open/short-
speed. damaged (Please check it by referring to the
circuited
resistance table for temperature sensor).

4. Main board is damaged.

1. The wiring terminal between indoor
evaporator temperature sensor and main
board is loosened or poorly contacted.

Indoor 2. Theres short circuit due to the trip-over of

Compressor and the parts on main board.
evaporator
OFF 3S draw water motor
temperature
2 F2 and blinks stop operation. Fan
sensor is
twice operates at set fan
open/short- 3.Indoor evaporator temperature sensor is
speed.
circuited damaged (Please check it by referring to the
resistance table for temperature sensor).

4. Main board is damaged.

1. The wiring terminal between outdoor

condenser temperature sensor and main
board is loosened or poorly contacted.
Outdoor
Compressor and
condenser 2. Theres short circuit due to the trip-over of
OFF 3S draw water motor
temperature the parts on main board.
3 F4 and blinks stop operation. Fan
sensor is
4 times operates at set fan
open/short- 3. Outdoor condenser temperature sensor is
speed.
circuited damaged (Please check it by referring to the
resistance table for temperature sensor).

4. Main board is damaged.

Disconnect power, and then turn on the unit
Overcurrent again after 10min. If "E5" still exits, please
4 E5
protection contact professional person to maintain the
unit.

Maintenance 27
 Service Manual

Display Method of Indoor Unit

Indicator lamp
(During blinking, ON for 0.5S and
Malfunction OFF for 0.5 S)
NO. Error A/C Status Possible Causes
Name Code
Operation COOL HEAT
Inidicato Indicator Indicator

During cooling or drying

operation,condensate water will flow into
Water chassis. If its detected that water inside
The unit stops
5 over-flow H8 water chassis is full for 3s successively,
operation
protection it comes into water over-flow protection.
Buzzer will give out 8 sounds and dual-8
nixie tube displays error code “H8”.

1. Heat exchangers are too dirty or the air

inlet/outlet is blocked.
Indoor fan runs
2. Compressor doesnt work normally. Strange
Insufficient according to set fan
noise or leakage occurs. Temperature of the
6 fluorine F0 and other loads will
shell is too high.
protection stop.
3. System is blocked inside(dirt block, ice
block, oil block, Y-valve not fully open).
4. The refrigerant is leaking.

1. Heat exchangers are too dirty or the air

inlet/outlet is blocked.
2. Fan motor is not working Abnormal fan
speed; fan speed is too low or the fan doesnt
run.
Indoor fan runs 3. Compressor doesnt work normally. Strange
Overload according to set fan noise or leakage occurs. Temperature of the
7 protection for H3 and other loads will shell is too high.
compressor stop. 4. System is blocked inside(dirt block, ice
block, oil block, Y-valve not fully open).
5. Draw-water motor cant operate normally.
6. Water outlet hasnt been blocked well by
rubber cork .
7. The refrigerant is leaking and cause
overheating protection to compressor.

1. The environment is formidable.

2. Heat exchangers are too dirty or the air
inlet/outlet is blocked.
During cooling or
3. Fan motor is not working Abnormal fan
drying operation,
speed; fan speed is too low or the fan doesnt
indoor fan operates,
run.
Overload while compressor,
8 E8 4. Compressor doesnt work normally. Strange
malfunction outdoor fan and
noise or leakage occurs. Temperature of the
water-striking
shell is too high.
motor stop. “E8” is
5. System is blocked inside(dirt block, ice
displayed.
block, oil block, Y-valve not fully open).
6.Temperature sensor of main board cant
detect correctly.

28 Maintenance
 Service Manual

9.2 Malfunction Detection Flowchart

(1) Malfunction of temperature sensor F1, F2, F4

Troubleshooting for
F1,F2,F4 malfunction

Is
the wiring terminal between the
temperature sensor and the controller Yes
loosened or poorly contacted?

Insert the temperature

sensor tightly

No
Is malfunction
No eliminated

Is there short circuit due to trip-over of Yes

the parts?

Make the parts upright

No

No Is malfunction Yes
eliminated

Is the
temperature sensor normal according No
to the Resistance
Table?

Replace it with a
temperature sensor
with the same model

Yes

No Is malfunction Yes
removed

Replace the mainboard

with the same model.
Yes

End

Maintenance 29
 Service Manual

(2) Malfunction of Overcurrent Protection E5

Troubleshooting
for E5 malfunction

Is the supply voltage unstable Normal fluctuation is within 10 % of the rated Malfunction is
with big fluctuation? Yes Yes
voltage on the nameplate eliminated

No

Is the supply voltage too low Adjust the supply voltage to maintain it within Malfunction is
Yes Yes
with overload? normal range eliminated

No

No

Is the indoor / outdoor

Clean the indoor and outdoor heat exchangers Malfunction is
heat exchanger too dirty,or are the air inlet Yes Yes
and remove the blockage of air inlet and outlet eliminated
and outlet blocked?

No No

The fan is abnormal? Fan Check the motor and reinstall the motor to have Malfunction is
speed is too low or fan doesn’t rotate Yes the fan run normally
Yes
eliminated

No No

Measure the
current of live wireon the main
board with a clamp ampere meter. Is the Replace the mainboard with the same model Malfunction is Yes
No
current higher than the value of the eliminated
overcurrent protection?

Yes
No

Is there blockage inside

the system? (Filth blockage, ice plug, Flush the heat exchangers with high pressure Malfunction is
greasy blockage, the Y-valve hasn’t been opened Yes Yes
completely) nitrogen eliminated

No
No

Is the compressor running

abnormally? Is there abnormal sound or oil Malfunction is
Yes Replace the mainboard with the same model Yes
leakage; is the temperature of the shell eliminated
too high, etc.?

No
No

Replace the mainboard with

the same model

End

30 Maintenance
 Service Manual

(3) Bucket full protection H8

Start up the unit

H8 is displayed

Discharge water by referring

Whether water tray is full Yes to instruction manual

No

Check whether wires for water-level No Whether malfunction

switch are connected tightly is eliminated?
No

Yes
Adjust connection

Yes

Whether malfunction
No Replace water-level is eliminated?
Whether malfunction
switch
is eliminated? No

Replace the main board

Yes with the same model
Yes

End

Maintenance 31
 Service Manual

4 (4)㕪≏᭵䳌
Malfunction
F0ᧂḕ⍱〻of Insufficient fluorine protection F0

Troubleshooting
for F0 malfunction

Heat exchangers are Clean the heat exchangers and remove

Yes Malfunction is Yes
too dirty or the air inlet/outlet eliminated.
is blocked.
blockage of air inlet/outlet.

No No

Compressor doesn't work Malfunction is

normally. Strange noise or leakage occurs. Yes Make compressor run normally. eliminated.
Yes
Casing is too hot.

No No

System is blocked inside

(dirt block, ice block, oil block, Y-valve no Yes Remove blockage in the system Malfunction is Yes
eliminated.
fully open).

No No

Check the leaking status of refrigerant Malfunction is Yes

The refrigerant is leaking Yes eliminated.
and charge refrigerant

No No

Replace a main
board with the
same model.

End

32 Maintenance
 Service Manual

5 (5) ঻㕙ᵪ䗷䖭᭵䳌 H3ᧂḕ⍱〻

Malfunction of Overload protection for compressor H3

Troubleshooting
for H3 malfunction

Heat exchangers are Clean the heat exchangers and remove

Yes Malfunction is Yes
too dirty or the air inlet/outlet eliminated.
is blocked.
blockage of air inlet/outlet.

No No

Fan motor is not working

Yes Check motor and re-install the moto Malfunction is Yes
Abnormal fan speed; fan speed is too low
to make it run normally. eliminated.
or the fan doesn't run.

No No

Compressor doesn't work Malfunction is

normally. Strange noise or leakage occurs. Yes Make compressor run normally. eliminated.
Yes
Casing is too hot.

No No

System is blocked inside

(dirt block, ice block, oil block, Y-valve no Yes Remove blockage in the system. Malfunction is Yes
eliminated.
fully open).

No No

Draw-water motor can't operate Yes Replace the draw-water motor. Malfunction is Yes
normally. eliminated.

No No

Water outlet hasn't been blocked well Block the water outlet well. Malfunction is Yes
Yes eliminated.
by rubber cork.

No No

The refrigerant is leaking Check the leaking status of refrigerant Malfunction is Yes
and cause overheating protection to Yes eliminated.
compressor. and charge refrigerant.

No No

Replace a main
board with the
same model.

End

Maintenance 33
 Service Manual

(6) Overload malfunction E8

Troubleshooting
for E8 malfunction

Operate the unit after ambient tempeature and

Whether the environment Yes humidity is decreased or move the unit to the Malfunction is Yes
is formidable place with low abient temprature and humidity. eliminated.

No No

Heat exchangers are Clean the heat exchangers and remove

Yes Malfunction is Yes
too dirty or the air inlet/outlet eliminated.
is blocked.
blockage of air inlet/outlet.

No No

Fan motor is not working

Yes Check motor and re-install the moto Malfunction is Yes
Abnormal fan speed; fan speed is too low
to make it run normally. eliminated.
or the fan doesn't run.

No No

Compressor doesn't work Malfunction is

normally. Strange noise or leakage occurs. Yes Make compressor run normally. eliminated.
Yes
Casing is too hot.

No No

System is blocked inside

(dirt block, ice block, oil block, Y-valve no Yes Remove blockage in the system. Malfunction is Yes
eliminated.
fully open).

No No

Temperature sensor of main board Yes Replace the temperature sensor. Malfunction is Yes
can't detect correctly. eliminated.

No No

Replace a main
board with the
same model.

End

34 Maintenance
 Service Manual

9.3 Maintenance Method for Common Malfunction

1. Air Conditioner Cant be Started Up

Possible Causes for Malfunction Distinguish Method (A/C status) Maintenance Method
No power supply; power plug
Check whether theres power supply;
hasnt been inserted tightly and Operation indicator is OFF and buzzer wont give
Check power plug and wire connection.
poorly connected; wires hasnt out sound.
been connected well.
Ambient temperature sensor is
damaged (no connection, loosen, After energization, the unit will give out a sound,
Check wire connection of temperature sensor or
wires are damaged, resistance while it cant be started up after pressing ON/OFF
replace temperature sensor.
value for temperature sensor is button.
abnormal).
Make sure the air conditioner is grounded
reliably.
Make sure wires of air conditioner is connected
After energization, room circuit breaker trips off at
Electric leakage for air conditioner correctly.
once.
Check the wiring inside air conditioner. Check
whether the insulation layer of power cord is
damaged; if yes, place the power cord.
Model selection for air switch is
After energization, air switch trips off. Select proper air switch.
improper
After energization, operation indicator is bright,
Replace batteries for remote controller.
Malfunction of remote controller while no display on remote controller or buttons
Repair or replace remote controller.
have no action.
Water inside water chassis is full Discharge condensate water.
Dual8 nixie tube displays H8 and buzzer gives
Check water-level switch and connection (refer
Malfunction of water-level switch out 8 sounds (water over-flow protection).
to detection flow chart 3).

2. Poor Cooling (Heating) for Air Conditioner

Possible Causes Discriminating Method (Air conditioner Status) Troubleshooting

Set temperature is improper Observe the set temperature on remote controller Adjust the set temperature.
Fan speed is set too slow Small fan blow at air outlet Set the fan speed at high or medium.
Check the filter to see whether its blocked by
Filter unit is blocked Clean the filter.
sundries
Discharged air temperature during cooling is
higher than normal discharged wind temperature;
Discharged air temperature during heating is Find out the leakage causes and deal with it.
Refrigerant is leaking
lower than normal discharged wind temperature; Add refrigerant.
Units pressure is much lower than regulated
range
Has set COOL (DRY) mode, but theres no cool The system is defrosting. Resume operation
Evaporator is frosted
fan after defrosting is finished.
Discharged air temperature during cooling is
higher than normal discharged wind temperature;
Discharged air temperature during heating is
Malfunction of capillary lower than normal discharged wind temperature; Replace the capillary.
Unitt pressure is much lower than regulated
range. If refrigerant isnt leaking, part of capillary
is blocked
Refer to point 3 for detailed maintenance
Malfunction of fan Fan cant operate
method.
Refer to point 4 of maintenance method for
Malfunction of compressor Compressor cant operate
details.

Maintenance 35
 Service Manual

3. Fan Cant Swing

Possible Causes Discriminating Method (Air conditioner Status) Troubleshooting

Connect wires according to wiring diagram to
Wrong wire connection, or poor Check the wiring status according to circuit
make sure all wiring terminals are connected
connection diagram
firmly
Use universal meter to measure voltage at both
Fan capacitor is damaged Replace fan capacitor
ends of fan capacitor
Supply voltage is too low or too You are suggested to equip with voltage
Use universal meter to measure the voltage
high regulator
Above circumstances are normal, while the fan
Motor is damaged Repair or replace motor
cant operate

4. Compressor Cant Operate

Possible causes Discriminating method (air conditioner status) Troubleshooting

Connect wires according to wiring diagram to
Wrong wire connection, or poor Check the wiring status according to circuit
make sure all wiring terminals are connected
connection diagram
firmly
Measure the capacity of fan capacitor with an
C a p a c i t y o f c o m p r e s s o r i s universal meter and find that the capacity is out of
Replace the compressor capacitor
damaged the deviation range indicated on the nameplate of
fan capacitor.
Power voltage is a little low or Use universal meter to measure the power supply
Suggest to equip with voltage regulator
high voltage. The voltage is a little high or low
Use universal meter to measure the resistance
Coil of compressor is burnt out Repair or replace compressor
between compressor terminals and its 0
Cylinder of compressor is blocked Compressor cant operate Repair or replace compressor

5. Unit hasnt stop operation afer bucket full or bucket full protection occurs frequently

Possible causes Discriminating method (air conditioner status) Troubleshooting

Water-level switch is open- The unit hasnt stop operation when water is full
Check and repair the water-level switch
circuited and theres water leakage
Water over-flow protection occurs frequently and
Draw water motor is damaged Replace draw water motor
H8 is displayed

6. Abnormal Sound and Vibration

Possible causes Discriminating method (air conditioner status) Troubleshooting
When turn on or turn off the unit,
the panel and other parts will Normal phenomenon. Abnormal sound will
Theres the sound of "PAPA"
expand and theres abnormal disappear after a few minutes.
sound
When turn on or turn off the
unit, theres abnormal sound due Normal phenomenon. Abnormal sound will
Water-running sound can be heard
to flow of refrigerant inside air disappear after a few minutes.
conditioner
Therere foreign objects inside air Take out foreign objects. Adjust the position of
conditioner or parts are contacting Abnomal sound parts. Stick damping plaster between contacting
with each other parts.
Adjust the support foot mat of compressor,
Abnormal shake of compressor Outdoor unit gives out abnormal sound
tighten the bolts.
If add too much refrigerant during maintenance,
Abnormal sound inside the
Abnormal sound inside the compressor please reduce refrigerant properly. Replace
compressor
compressor for other circumstances.

36 Maintenance
 Service Manual

10. Exploded View and Parts List

GPC12AL-K3NNA1A

51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
34
52 33
53 32
31
54 30
55 29
28
56 27
57 26
58 25
59 24
60 23
61 22
62 21
20
19
18
63 17
64 16
65
15
14
13
12
66 67 68 69 70 1 2 3 4 5 6 7 8 10 11
9

71 72 73 74 75 76 77

The component picture is only for reference please refer to the actual product.

Maintenance 37
 Service Manual

Part Code
Description
NO. GPC12AL-K3NNA1A GPC12AL-K3NNA1A Qty
Product Code CK010025700 CK010025702
1 Foam (Inching Switch) 12316037 12316037 1
2 Inching Switch 45017005 45017005 1
3 Water Level Switch Base 20011500074 20011500074 1
4 Water level switch sub-assy 194000003 194000003 4
5 Chassis Assy 209058000005 209058000025 1
6 Castor 24236009 24236009 1
7 Chassis Sub-assy 20902000020 2090200002002 1
8 Fan Motor 1501606303 150101000003 1
9 Splash Water Flywheel 10336003 10336003 1
10 Motor Sub-assy(Flutter) 000089000001 000089000001 1
11 Compressor and Fittings 009001000003 009001000003 1
12 Supporting Board 1 01796035 01796035 1
13 Condenser Assy 011002000093 011002000093 1
14 Diversion Circle 10376064 10376064 1
15 Centrifugal Fan 10316079 10316079 4
16 Rear Grill 01476050 01476050 1
17 Motor Holder 26156103 26156103 1
18 Fan Motor 150101000003 150101000003 1
19 Air Flue Assy 1 017107000003 017107000003 1
20 Foam (Water Tray) 12316052 12316052 1
21 Rear Grill 01476040 01476050 1
22 Diversion Circle 10376065 10376065 1
23 Right Side Plate 20056186 2005618601P01 1
24 Wire Clamp 71010103 71010103 1
25 Rear Plate 20024500010 2002450001002P01 1
26 Cable Cross Plate 26116226 2611622602P01 1
27 Cover of drainage hole 2224609701 2224609702P01 1
28 Rubber Plug 76716054 76716054 1
29 Filter Sub-assy 1 11126042 11126042 1
30 Front Grill Asmy 000087000001 2241607402P01 1
31 Centrifugal Fan 10316079 10316071 1
32 Motor Holder 26156104 26156104 1
33 Fan Motor 1501606303 15010100000301 1
34 Air Flue Assy 2 017107000004 017107000004 1
35 Cover of Propeller Housing 20022300013 20022300013 1
36 Display Board 300001000001 300001000001 1
37 Fixed support (Top Cover) 20011500075 2001150007502S01 1
38 Display Board 300001000001 300001000001 1
39 Top Cover 22246157 2224615701P01 1
40 Membrane 60516017 600006000012 1
41 Top Cover Assy 000097000007 000097000029 1
42 Supporting Board 3 01207200097 01207200097 4
43 Electric Box Cover 01202000107 01202000107 1
44 Capacitor CBB61S 3301074705 3301074705 1
45 Capacitor CBB65 3300008102 3300008102 1
46 Temperature Sensor 390000453 390000453 1
47 Temperature Sensor 390000597 390000453 1
48 Temperature Sensor 3900032101 390000597 1
49 Main Board 300002000004 300002000004 1
50 Fixed support (mainboard) 20011500076 20011500076 1
51 Electric Box Sub-Assy 01700700101 01700700101 1
52 Electric Box Assy 100002000260 100002000260 1
53 Filter Sub-assy 2 11126043 11126043 1
54 Evaporator Assy 011001000114 011001000114 1

38 Maintenance
 Service Manual

55 Left Side Plate 20056185 2005618501P01 1

56 Guide Louver 2 10516098 1051609802P 1
57 Guide Louver 1 10516099 1051609902P 1
58 Guide Blade Lever 20023500011 2002350001102 4
59 Swing Lever 20003500025 2000350002502 1
60 Air Louver 3 10516102 1051610202P 1
61 Air Louver 2 10516101 1051610102P 1
62 Air Louver 1 10516100 1051610002P 1
63 Front Panel 20000300144 2000030014402P01 1
64 Decorative Strip 23000100071 23000100071P01 1
65 Front Panel Assy 209004000002 209004000006 1
66 Capillary Sub-assy 030006000094 030006000094 1
67 Inhalation Tube Assy 030010000228 030010000228 1
68 Discharge Tube 035008000416 035008000416 1
69 Supporting Strip 01796007 01796007 4
70 Cold Plasma Generator 1114001601 1114001601 1
71 Power Cord 400204648 400204648 1
72 Remote Controller 305100611 305100611 1
73 Drainage Hose 05230013 05230013 1
74 Joint 20010900023 20010900023 1
75 Pipe 05236058 05236058 1
76 Rear Clip (upper) 26116132 26116132 1
77 Rear Clip (nether) 26116135 26116135 1

Above data is subject to change without notice.

Maintenance 39
 Service Manual

GPH12AL-K3NNA1A

51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
34
52 33
53 32
31
54 30
55 29
28
56 27
57 26
58 25
59 24
60 23
61 22
62 21
20
19
18
63 17
64 16
65
15
14
13
12
66 67 68 69 70 1 2 3 4 5 6 7 8 10 11
9

71 72 73 74 75 76 77

The component picture is only for reference please refer to the actual product.

40 Maintenance
 Service Manual

Part Code
Description
NO. GPH12AL-K3NNA1A Qty
Product Code CK010024500
1 Foam (Inching Switch) 12316037 1
2 Inching Switch 45017005 1
3 Water Level Switch Base 20011500074 1
4 Water level switch sub-assy 194000003 4
5 Chassis Assy 209058000005 1
6 Castor 24236009 1
7 Chassis Sub-assy 20902000020 1
8 Fan Motor 1501606303 1
9 Splash Water Flywheel 10336003 1
10 Motor Sub-assy(Flutter) 000089000001 1
11 Compressor and Fittings 009001000003 1
12 Supporting Board 1 01796035 1
13 Condenser Assy 011002000093 1
14 Diversion Circle 10376064 1
15 Centrifugal Fan 10316079 4
16 Rear Grill 01476040 1
17 Motor Holder 26156103 1
18 Fan Motor 150101000003 1
19 Air Flue Assy 1 017107000003 1
20 Foam (Water Tray) 12316052 1
21 Rear Grill 01476050 1
22 Diversion Circle 10376065 1
23 Right Side Plate 20056186 1
24 Wire Clamp 71010103 1
25 Rear Plate 20024500010 1
26 Cable Cross Plate 26116226 1
27 Cover of drainage hole 2224609701 1
28 Rubber Plug 76716054 1
29 Filter Sub-assy 1 11126042 1
30 Front Grill Asmy 000087000001 1
31 Centrifugal Fan 10316071 1
32 Motor Holder 26156104 1
33 Fan Motor 15010100000301 1
34 Air Flue Assy 2 017107000004 1
35 Cover of Propeller Housing 20022300013 1
36 Display Board 300001000040 1
37 Fixed support (Top Cover) 20011500075 1
38 Display Board 300001000001 1
39 Top Cover 22246157 1
40 Membrane 60516016 1
41 Top Cover Assy 000097000007 1
42 Supporting Board 3 01207200097 4
43 Electric Box Cover 01202000107 1
44 Capacitor CBB61S 3301074705 1
45 Capacitor CBB65 3300008102 1
46 Temperature Sensor 390000453 1
47 Temperature Sensor 390000597 1
48 Temperature Sensor 3900032101 1
49 Main Board 30137064 1
50 Fixed support (mainboard) 20011500076 1
51 Electric Box Sub-Assy 01700700101 1
52 Electric Box Assy 100002000084 1
53 Filter Sub-assy 2 11126043 1
54 Evaporator Assy 011001000048 1

Maintenance 41
 Service Manual

55 Left Side Plate 20056185 1

56 Guide Louver 2 10516098 1
57 Guide Louver 1 10516099 1
58 Guide Blade Lever 20023500011 4
59 Swing Lever 20003500025 1
60 Air Louver 3 10516102 1
61 Air Louver 2 10516101 1
62 Air Louver 1 10516100 1
63 Front Panel 20000300144 1
64 Decorative Strip 23000100071 1
65 Front Panel Assy 209004000002 1
66 Capillary Sub-assy 030006000094 1
67 4-Way Valve Assy 030152000057 1
68 Magnet Coil 430004017 1
69 Supporting Strip 01796007 4
70 Cold Plasma Generator 1114001601 1
71 Power Cord 400204648 1
72 Remote Controller 305100611 1
73 Drainage Hose 05230013 1
74 Joint 20010900023 1
75 Pipe 05236058 1
76 Rear Clip (upper) 26116132 1
77 Rear Clip (nether) 26116135 1
Above data is subject to change without notice.

42 Maintenance
 Service Manual

GPH12AL-K3NNA2A

51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
34
52 33

53 32
31
54 30
55 29
28
56 27
57 26
58 25
59 24
60 23
61 22
62 21
20
19
18
63 17
64 16
65
15
14
13
12
66 67 68 69 70 1 2 3 4 5 6 7 8 10 11
9

71 72 73 74 75 76 77

The component picture is only for reference please refer to the actual product.

Maintenance 43
 Service Manual

Part Code
Description
NO. GPH12AL-K3NNA2A Qty
Product Code CK010025800
1 Buoy 12316037 1
2 Inching Switch 45017005 1
3 fixed support (Compressor) 20011500074 1
4 Liquid Level Switch Sub-assy 000194000003 4
5 Chassis Assy 209058000005 1
6 Castor 24236009 1
7 Chassis Sub-assy 20902000020 1
8 Fan Motor 150101000003 1
9 Splash Water Flywheel 10336003 1
10 Motor Sub-assy(Flutter) 000089000001 1
11 Compressor and Fittings 009001000003 1
12 Supporting Board 1 01796035 1
13 Condenser Assy 011002000093 1
14 Diversion Circle (Upper) 10376065 1
15 Centrifugal Fan 10316079 4
16 Rear Grill 01476050 1
17 Motor Holder 26156103 1
18 Fan Motor 150101000003 1
19 Air Duct Sub-assy 1 017107000003 1
20 Foam (Water Tray) 12316052 1
21 Rear Grill 01476050 1
22 Diversion Circle (lower) 10376064 1
23 Right Side Plate 200086000001 1
24 Wire Clamp 71010103 1
25 Rear Plate 20024500010 1
26 Cable Cross Plate 26116226 1
27 Cover of drainage hole 2224609701 1
28 Rubber Plug 06816101 1
29 Filter Sub-assy 1 11126042 1
30 Front Grill 22416074 1
31 Centrifugal Fan 10316071 1
32 Motor Holder 26156104 1
33 Fan Motor 15010100000301 1
34 Air Duct Sub-assy 2 017107000004 1
35 Cover of Propeller Housing 20022300013 1
36 Display Board 300001000001 1
37 Fixed support (Top Cover) 20011500075 1
38 Display Board 300001000001 1
39 Coping 22246157 1
40 Membrane 60516016 1
41 Top Cover Assy 000097000007 1
42 Supporting Board 3 01207200097 4
43 Electric Box Cover 01202000107 1
44 Capacitor CBB61S 3301074705 1
45 Capacitor CBB65 3300008102 1
46 Temperature Sensor 390000453 1
47 Temperature Sensor 390000597 1
48 Temperature Sensor 390000597 1
49 Main Board 30137064 1
50 fixed support (mainboard) 20011500076 1
51 Electric Box Sub-Assy 01700700101 1
52 Electric Box Assy 100002000084 1
53 Filter Sub-assy 2 11126043 1
54 Evaporator Assy 011001000048 1

44 Maintenance
 Service Manual

55 Left Side Plate 200085000001 1

56 Guide Louver 2 10516098 1
57 Guide Louver 1 10516099 1
58 Guide Blade Lever 20023500011 4
59 Swing Lever 20003500025 1
60 Air Louver 3 10516102 1
61 Air Louver 2 10516101 1
62 Air Louver 1 10516100 1
63 Front Panel 200003000002 1
64 Decorative Strip 23000100071 1
65 Front Panel Sub-Assy 209004000004 1
66 Capillary Sub-assy 030006000094 1
67 4-Way Valve 430004032 1
68 Magnet Coil 430004017 1
69 Supporting Strip 01796007 4
70 Cold Plasma Generator 1114001601 1
71 Power Cord 400204648 1
72 Remote Controller 305100611 1
73 Drainage Hose 05230013 1
74 Tie-in 1 20010900023 1
75 Pipe 05236058 1
76 Rear Clip (upper) 26116132 1
77 Rear Clip (nether) 26116135 1

Above data is subject to change without notice.

Maintenance 45
 Service Manual

GPH12AL-K3NNA3A

51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35
34
52 33
53 32
31
54 30
55 29
28
56 27
57 26
58 25
59 24
60 23
61 22
62 21
20
19
18
63 17
64 16
65
15
14
13
12
66 67 68 69 70 1 2 3 4 5 6 7 8 10 11
9

71 72 73 74 75 76 77

The component picture is only for reference please refer to the actual product.

46 Maintenance
 Service Manual

Part Code
Description
NO. GPH12AL-K3NNA3A Qty
Product Code CK010025900
1 Buoy 12316037 1
2 Inching Switch 45017005 1
3 fixed support (Compressor) 20011500074 1
4 Liquid Level Switch Sub-assy 000194000003 4
5 Chassis Assy 209058000019 1
6 Castor 24236009 1
7 Chassis Sub-assy 2090200002001 1
8 Fan Motor 150101000003 1
9 Splash Water Flywheel 10336003 1
10 Motor Sub-assy(Flutter) 000089000001 1
11 Compressor and Fittings 009001000003 1
12 Supporting Board 1 01796035 1
13 Condenser Assy 011002000093 1
14 Diversion Circle (Upper) 10376065 1
15 Centrifugal Fan 10316079 4
16 Rear Grill 01476050 1
17 Motor Holder 26156103 1
18 Fan Motor 150101000003 1
19 Air Duct Sub-assy 1 017107000003 1
20 Foam (Water Tray) 12316052 1
21 Rear Grill 01476050 1
22 Diversion Circle (lower) 10376064 1
23 Right Side Plate 200086000002 1
24 Wire Clamp 71010103 1
25 Rear Plate 2002450001001 1
26 Cable Cross Plate 2611622601 1
27 Cover of drainage hole 22246097 1
28 Rubber Plug 06816101 1
29 Filter Sub-assy 1 1112604201 1
30 Front Grill 2241607401 1
31 Centrifugal Fan 10316071 1
32 Motor Holder 26156104 1
33 Fan Motor 15010100000301 1
34 Air Duct Sub-assy 2 017107000004 1
35 Cover of Propeller Housing 20022300013 1
36 Display Board 300001000001 1
37 Fixed support (Top Cover) 2001150007501T 1
38 Display Board 300001000001 1
39 Coping 22246157 1
40 Membrane 60516016 1
41 Top Cover Assy 000097000027 1
42 Supporting Board 3 01207200097 4
43 Electric Box Cover 01202000107 1
44 Capacitor CBB61S 3301074705 1
45 Capacitor CBB65 3300008102 1
46 Temperature Sensor 390000453 1
47 Temperature Sensor 390000597 1
48 Temperature Sensor 390000453 1
49 Main Board 30137064 1
50 fixed support (mainboard) 20011500076 1
51 Electric Box Sub-Assy 01700700101 1
52 Electric Box Assy 100002000084 1
53 Filter Sub-assy 2 11126043 1
54 Evaporator Assy 011001000048 1

Maintenance 47
 Service Manual

55 Left Side Plate 200085000002 1

56 Guide Louver 2 1051609801 1
57 Guide Louver 1 1051609901 1
58 Guide Blade Lever 2002350001101 4
59 Swing Lever 2000350002501 1
60 Air Louver 3 1051610201 1
61 Air Louver 2 1051610101 1
62 Air Louver 1 1051610001 1
63 Front Panel 200003000009 1
64 Decorative Strip 2300010007101 1
65 Front Panel Sub-Assy 209004000005 1
66 Capillary Sub-assy 030006000094 1
67 4-Way Valve 430004032 1
68 Magnet Coil 430004017 1
69 Supporting Strip 01796007 4
70 Cold Plasma Generator 1114001601 1
71 Power Cord 400204648 1
72 Remote Controller 305100611 1
73 Drainage Hose 05230013 1
74 Tie-in 1 20010900023 1
75 Pipe 05236058 1
76 Rear Clip (upper) 26116132 1
77 Rear Clip (nether) 26116135 1
Above data is subject to change without notice.

48 Maintenance
 Service Manual

Warning: disconnect power supply before

11. Removal Procedure removal; discharge the refrigerant completely
before unsoldering the pipes.

Note:Take A1 panel for example.

Step Procedure

1.Remove front grill and filter sub-assy 2

Front grill Filter Sub-assy 2

Front grill Filter sub-assy 2

Pull the filter sub-assy 2 outward by

hand to remove the filter.

2. Remove left & right side plate

Left & right side plate

Remove left side plate: unscrew 2

screws as diagram shown to remove
left side plate.
Remove right side plate: unscrew
2 screws of right side plate to remove it.

Srews

3.Remove rear plate

Cable cross plate
Real plare

Remove the 12 screws fixing rear

plate to remove the rear plate and cable
cross plate and cable cross plate and
rubber plug.

Cover of drainage
Screws hole
Rubber Plug

Maintenance 49
 Service Manual

Step Procedure

4.Remove top cover assy

Screws Top cover assy

Remove the 4 screws to remove

the top cover assy.

5.Remove front panel assy Screws Front panel sub-assy

Remove the four screws fixing

front panel to remove the front
panel sub-assy.

6.Remove electric box cover

Electric box cover

Unscrew 4 screws to remove the
electric box cover assy and wire Electric box cover assy
clamp.
Screws

Screws

Wire Clamp

50 Maintenance
 Service Manual

Step Procedure

7. Remove Supporting Board 3

Supporting Board 3
Screws

Unscrew 2 screws to remove the

Supporting board 3.

8. Remove Cover of Propeller Housing Cover of Propeller Housing

Screws
Unscrew 7 screws to remove the
cover of propeller housing.

9. Remove Evaporator Assy

Screws Evaporator assy

Unscrew 5 screws to remove the
evaporator assy.

Maintenance 51
 Service Manual

Step Procedure

10. Remove Air Flue Assy 2

Screws Air Flue Assy 2

Unscrew 4 screws to remove the

air flue assy 2.

Cold Plasma Diversion Circle

Generator

Unscrew 3 screws to remove the

diversion circle and cold plasma
b Cold Plasma Generator
generator assy.
assy
Screws

Nut
Unscrew 5 screws to remove the nut Gasket
Nut assy
assy and gasket and centrifugal and
motor holder(upper). Gasket(M6)

c
Centrifugal Fan Rear Grill

Motor Holder(upper)
Screws

Fan Motor

52 Maintenance
 Service Manual

Step Procedure

11. Remove Air Flue Assy 1

Foam (Water Tray)

Screws

Unscrew 6 screws to remove the Air Flue Assy 1

air flue assy 1 and foam(water tray).

Diversion Circle
Unscrew 6 screws to remove the
diversion circle and rear grill.
b
Screws
Rear Grill

Nut

Nut assy
Gasket
Unscrew screws to remove the nut
assy and gasket and centrifugal and Centrifugal Fan Gasket(M6)
motor holder.

c Motor Holder

Screws
Fan Motor

Maintenance 53
 Service Manual

Step Procedure
12. Remove supporting board and supporting
strip
Screws
Supporting Board 1
Unscrew 4 screws to remove
supporting board 1 and supporting strip.

Supporting Strip

13. Remove 4-way valve interface

4-way valve interface

Unscrew screws to remove the Capillary Sub-assy 4-way valve interface
4-way valve interface and capillary
sub-assy.

Screws

14. Remove condenser assy

Condenser Assy

Unscrew screws to remove condenser

assy.

Screws

54 Maintenance
 Service Manual

Step Procedure
Water level switch sub-assy
15. Remove water level switch sub-assy Screws

Unscrew 4 screws to remove the water level

switch sub-assy.

16 Remove
. compressor and fittings

Bolts
Unscrew 3 bolts of compressor chassis,
then take out gasket to remove compressor.
Compressor
and fittings

Bolts

17. Remove motor sub-assy(flutter)

Screws
Motor sub-assy(flutter)

Unscrew 2 screws of bottom of

sub-assy to remove motor sub-assy.

Maintenance 55
 Service Manual

Step Procedure

18. Remove chassis sub-assy

Chassis Sub-assy
Screws

Unscrew 4 screws fixing caster wheel

to remove the 4 caster wheels.

Caster wheels

56 Maintenance
 Service Manual

Appendix:
Appendix 1: Reference Sheet of Celsius and Fahrenheit
Conversion formula for Fahrenheit degree and Celsius degree: Tf=Tcx1.8+32
Set temperature
Fahrenheit Fahrenheit Fahrenheit
display Fahrenheit display Fahrenheit display Fahrenheit
Celsius（℃） Celsius（℃） Celsius（℃）
temperature （℉） temperature （℉） temperature （℉）
（℉） （℉） （℉）
61 60.8 16 69/70 69.8 21 78/79 78.8 26
62/63 62.6 17 71/72 71.6 22 80/81 80.6 27
64/65 64.4 18 73/74 73.4 23 82/83 82.4 28
66/67 66.2 19 75/76 75.2 24 84/85 84.2 29
68 68 20 77 77 25 86 86 30
Ambient temperature
Fahrenheit Fahrenheit Fahrenheit
display Fahrenheit display Fahrenheit display Fahrenheit
Celsius（℃） Celsius（℃） Celsius（℃）
temperature （℉） temperature （℉） temperature （℉）
（℉） （℉） （℉）
32/33 32 0 55/56 55.4 13 79/80 78.8 26
34/35 33.8 1 57/58 57.2 14 81 80.6 27
36 35.6 2 59/60 59 15 82/83 82.4 28
37/38 37.4 3 61/62 60.8 16 84/85 84.2 29
39/40 39.2 4 63 62.6 17 86/87 86 30
41/42 41 5 64/65 64.4 18 88/89 87.8 31
43/44 42.8 6 66/67 66.2 19 90 89.6 32
45 44.6 7 68/69 68 20 91/92 91.4 33
46/47 46.4 8 70/71 69.8 21 93/94 93.2 34
48/49 48.2 9 72 71.6 22 95/96 95 35
50/51 50 10 73/74 73.4 23 97/98 96.8 36
52/53 51.8 11 75/76 75.2 24 99 98.6 37
54 53.6 12 77/78 77 25

Maintenance 57
 Service Manual

Appendix 2: List of Resistance for Temperature Sensor

Resistance table of temperature sensor (15K)

Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ)

-19 138.1 20 18.75 59 3.848 98 1.071
-18 128.6 21 17.93 60 3.711 99 1.039
-17 121.6 22 17.14 61 3.579 100 1.009
-16 115 23 16.39 62 3.454 101 0.98
-15 108.7 24 15.68 63 3.333 102 0.952
-14 102.9 25 15 64 3.217 103 0.925
-13 97.4 26 14.36 65 3.105 104 0.898
-12 92.22 27 13.74 66 2.998 105 0.873
-11 87.35 28 13.16 67 2.896 106 0.848
-10 82.75 29 12.6 68 2.797 107 0.825
-9 78.43 30 12.07 69 2.702 108 0.802
-8 74.35 31 11.57 70 2.611 109 0.779
-7 70.5 32 11.09 71 2.523 110 0.758
-6 66.88 33 10.63 72 2.439 111 0.737
-5 63.46 34 10.2 73 2.358 112 0.717
-4 60.23 35 9.779 74 2.28 113 0.697
-3 57.18 36 9.382 75 2.206 114 0.678
-2 54.31 37 9.003 76 2.133 115 0.66
-1 51.59 38 8.642 77 2.064 116 0.642
0 49.02 39 8.297 78 1.997 117 0.625
1 46.6 40 7.967 79 1.933 118 0.608
2 44.31 41 7.653 80 1.871 119 0.592
3 42.14 42 7.352 81 1.811 120 0.577
4 40.09 43 7.065 82 1.754 121 0.561
5 38.15 44 6.791 83 1.699 122 0.547
6 36.32 45 6.529 84 1.645 123 0.532
7 34.58 46 6.278 85 1.594 124 0.519
8 32.94 47 6.038 86 1.544 125 0.505
9 31.38 48 5.809 87 1.497 126 0.492
10 29.9 49 5.589 88 1.451 127 0.48
11 28.51 50 5.379 89 1.408 128 0.467
12 27.18 51 5.197 90 1.363 129 0.456
13 25.92 52 4.986 91 1.322 130 0.444
14 24.73 53 4.802 92 1.282 131 0.433
15 23.6 54 4.625 93 1.244 132 0.422
16 22.53 55 4.456 94 1.207 133 0.412
17 21.51 56 4.294 95 1.171 134 0.401
18 20.54 57 4.139 96 1.136 135 0.391
19 19.63 58 3.99 97 1.103 136 0.382

58 Maintenance
 Service Manual

Resistance table of temperature sensor (20K)

Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ)

-19 181.4 20 25.01 59 5.13 98 1.427
-18 171.4 21 23.9 60 4.948 99 1.386
-17 162.1 22 22.85 61 4.773 100 1.346
-16 153.3 23 21.85 62 4.605 101 1.307
-15 145 24 20.9 63 4.443 102 1.269
-14 137.2 25 20 64 4.289 103 1.233
-13 129.9 26 19.14 65 4.14 104 1.198
-12 123 27 18.13 66 3.998 105 1.164
-11 116.5 28 17.55 67 3.861 106 1.131
-10 110.3 29 16.8 68 3.729 107 1.099
-9 104.6 30 16.1 69 3.603 108 1.069
-8 99.13 31 15.43 70 3.481 109 1.039
-7 94 32 14.79 71 3.364 110 1.01
-6 89.17 33 14.18 72 3.252 111 0.983
-5 84.61 34 13.59 73 3.144 112 0.956
-4 80.31 35 13.04 74 3.04 113 0.93
-3 76.24 36 12.51 75 2.94 114 0.904
-2 72.41 37 12 76 2.844 115 0.88
-1 68.79 38 11.52 77 2.752 116 0.856
0 65.37 39 11.06 78 2.663 117 0.833
1 62.13 40 10.62 79 2.577 118 0.811
2 59.08 41 10.2 80 2.495 119 0.77
3 56.19 42 9.803 81 2.415 120 0.769
4 53.46 43 9.42 82 2.339 121 0.746
5 50.87 44 9.054 83 2.265 122 0.729
6 48.42 45 8.705 84 2.194 123 0.71
7 46.11 46 8.37 85 2.125 124 0.692
8 43.92 47 8.051 86 2.059 125 0.674
9 41.84 48 7.745 87 1.996 126 0.658
10 39.87 49 7.453 88 1.934 127 0.64
11 38.01 50 7.173 89 1.875 128 0.623
12 36.24 51 6.905 90 1.818 129 0.607
13 34.57 52 6.648 91 1.736 130 0.592
14 32.98 53 6.403 92 1.71 131 0.577
15 31.47 54 6.167 93 1.658 132 0.563
16 30.04 55 5.942 94 1.609 133 0.549
17 28.68 56 5.726 95 1.561 134 0.535
18 27.39 57 5.519 96 1.515 135 0.521
19 26.17 58 5.32 97 1.47 136 0.509

Maintenance 59
 Service Manual

Resistance table of temperature sensor (50K)

Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ) Temp(oC) Resistance(kΩ)

-29 853.5 10 98 49 18.34 88 4.75
-28 799.8 11 93.42 50 17.65 89 4.61
-27 750 12 89.07 51 16.99 90 4.47
-26 703.8 13 84.95 52 16.36 91 4.33
-25 660.8 14 81.05 53 15.75 92 4.20
-24 620.8 15 77.35 54 15.17 93 4.08
-23 580.6 16 73.83 55 14.62 94 3.96
-22 548.9 17 70.5 56 14.09 95 3.84
-21 516.6 18 67.34 57 13.58 96 3.73
-20 486.5 19 64.33 58 13.09 97 3.62
-19 458.3 20 61.48 59 12.62 98 3.51
-18 432 21 58.77 60 12.17 99 3.41
-17 407.4 22 56.19 61 11.74 100 3.32
-16 384.5 23 53.74 62 11.32 101 3.22
-15 362.9 24 51.41 63 10.93 102 3.13
-14 342.8 25 49.19 64 10.54 103 3.04
-13 323.9 26 47.08 65 10.18 104 2.96
-12 306.2 27 45.07 66 9.83 105 2.87
-11 289.6 28 43.16 67 9.49 106 2.79
-10 274 29 41.34 68 9.17 107 2.72
-9 259.3 30 39.61 69 8.85 108 2.64
-8 245.6 31 37.96 70 8.56 109 2.57
-7 232.6 32 36.38 71 8.27 110 2.50
-6 220.5 33 34.88 72 7.99 111 2.43
-5 209 34 33.45 73 7.73 112 2.37
-4 198.3 35 32.09 74 7.47 113 2.30
-3 199.1 36 30.79 75 7.22 114 2.24
-2 178.5 37 29.54 76 7.00 115 2.18
-1 169.5 38 28.36 77 6.76 116 2.12
0 161 39 27.23 78 6.54 117 2.07
1 153 40 26.15 79 6.33 118 2.02
2 145.4 41 25.11 80 6.13 119 1.96
3 138.3 42 24.13 81 5.93 120 1.91
4 131.5 43 23.19 82 5.75 121 1.86
5 125.1 44 22.29 83 5.57 122 1.82
6 119.1 45 21.43 84 5.39 123 1.77
7 113.4 46 20.6 85 5.22 124 1.73
8 108 47 19.81 86 5.06 125 1.68
9 102.8 48 19.06 87 4.90 126 1.64

60 Maintenance
 Service Manual

Appendix 3: Resistance Value Table of Humidity Sensor

HIS-06 temperature and humidity characteristic5℃～ 14℃ Unit:KΩ

Relative
Temperature（℃）
humidity
%RH 5℃ 6℃ 7℃ 8℃ 9℃ 10℃ 11℃ 12℃ 13℃ 14℃
90 5.35 4.92 4.55 4.23 3.95 3.70 3.47 3.25 3.05 2.87
89 5.80 5.33 4.93 4.58 4.27 4.00 3.74 3.51 3.29 3.09
88 6.29 5.77 5.33 4.95 4.62 4.32 4.03 3.78 3.54 3.32
87 6.82 6.25 5.77 5.36 4.99 4.66 4.35 4.08 3.82 3.58
86 7.40 6.78 6.25 5.80 5.40 5.04 4.70 4.40 4.11 3.85
85 8.03 7.35 6.78 6.28 5.84 5.45 5.09 4.75 4.45 4.16
84 8.71 7.97 7.35 6.81 6.33 5.91 5.50 5.14 4.80 4.49
83 9.44 8.65 7.97 7.39 6.87 6.41 5.96 5.56 5.19 4.84
82 10.25 9.39 8.65 8.02 7.46 6.96 6.47 6.03 5.62 5.24
81 11.13 10.19 9.40 8.71 8.10 7.56 7.03 6.54 6.09 5.68
80 12.09 11.07 10.21 9.46 8.80 8.21 7.62 7.08 6.59 6.13
79 13.14 12.03 11.09 10.28 9.57 8.93 8.28 7.70 7.16 6.66
78 14.27 13.07 12.05 11.17 10.40 9.70 8.99 8.35 7.75 7.20
77 15.50 14.20 13.10 12.14 11.30 10.55 9.78 9.07 8.43 7.83
76 16.84 15.43 14.24 13.21 12.30 11.48 10.64 9.87 9.16 8.51
75 18.31 16.78 15.49 14.37 13.38 12.50 11.58 10.75 9.98 9.26
74 19.91 18.25 16.85 15.64 14.57 13.62 12.62 11.72 10.89 10.12
73 21.67 19.87 18.35 17.04 15.88 14.84 13.71 12.67 11.72 10.84
72 23.61 21.66 20.00 18.57 17.31 16.18 14.98 13.90 12.89 11.96
71 25.78 23.64 21.84 20.27 18.89 17.66 16.35 15.16 14.06 13.05
70 28.15 25.82 23.85 22.15 20.65 19.30 17.91 16.63 15.46 14.37
69 30.78 28.24 26.10 24.24 22.60 21.13 19.60 18.19 16.91 15.71
68 33.69 30.92 28.58 26.55 24.76 23.16 21.48 19.94 18.53 17.22
67 36.90 33.88 31.33 29.11 27.16 25.42 23.56 21.86 20.29 18.85
66 40.45 37.16 34.37 31.96 29.84 27.93 25.83 23.92 22.15 20.52
65 44.38 40.78 37.74 35.11 32.78 30.70 28.42 26.34 24.42 22.65
64 48.75 44.81 41.48 38.59 36.05 33.77 31.24 28.93 26.80 24.83
63 53.64 49.31 45.65 42.48 39.68 37.17 34.34 31.74 29.36 27.15
62 59.14 54.36 50.32 46.82 43.73 40.97 37.83 34.96 32.32 29.87
61 65.31 60.02 55.55 51.68 48.26 45.20 41.70 38.51 35.58 32.86
60 72.27 66.40 61.43 57.13 53.33 49.94 46.07 42.53 39.28 36.27
59 80.13 73.58 68.04 63.25 59.01 55.23 50.94 47.03 43.43 40.10
58 88.92 81.61 75.43 70.08 65.36 61.14 56.40 52.08 48.11 44.43
57 98.86 90.68 83.77 77.78 72.50 67.78 62.49 57.67 53.23 49.12
56 112.59 102.79 94.50 87.33 81.00 75.33 69.42 64.03 59.07 54.48
55 122.69 112.51 103.91 96.45 89.88 84.00 77.42 71.41 65.88 60.76
54 137.09 125.76 116.19 107.89 100.57 94.03 86.69 79.99 73.82 68.11
53 153.46 140.88 130.25 121.03 112.91 105.64 97.26 89.61 82.58 76.06
52 172.19 158.19 146.35 136.10 127.05 118.96 109.52 100.90 92.97 85.63
51 193.69 178.04 164.81 153.36 143.25 134.21 123.35 113.43 104.31 95.86
50 218.48 200.85 185.94 173.02 161.63 151.44 139.14 127.90 117.57 108.01
49 247.23 227.16 210.19 195.49 182.52 170.92 156.84 143.98 132.15 121.20
48 278.74 256.20 237.15 220.64 206.08 193.06 177.34 163.00 149.80 137.58
47 315.50 289.95 268.35 249.64 233.14 218.37 200.56 184.30 169.34 155.49
46 357.93 328.94 304.43 283.20 264.47 247.72 227.57 209.18 192.25 176.59
45 406.44 373.72 346.05 322.08 300.94 282.03 259.22 238.40 219.24 201.51
44 463.66 426.44 394.96 367.70 343.66 322.14 296.25 272.62 250.87 230.74
43 531.25 488.59 452.53 421.28 393.73 369.08 339.44 312.38 287.50 264.45
42 611.22 562.01 520.40 484.35 452.55 424.11 390.24 359.31 330.86 304.52
41 707.78 650.29 601.68 559.58 522.44 489.21 450.38 414.92 382.31 352.11
40 823.98 756.22 698.93 649.30 605.53 566.37 521.46 480.46 442.74 407.81
39 962.72 882.62 814.90 756.23 704.48 658.19 604.79 556.03 511.18 469.66

Maintenance 61
 Service Manual

38 1128.50 1033.61 953.39 883.90 822.61 767.78 704.83 647.37 594.51 545.56
37 1325.87 1213.40 1118.31 1035.94 963.29 898.30 823.48 755.17 692.34 634.16
36 1563.51 1430.14 1317.38 1219.71 1133.55 1056.48 967.04 885.39 810.28 740.74
35 1855.67 1695.83 1560.69 1443.63 1340.37 1248.00 1140.34 1042.06 951.64 867.93
34 2213.60 2020.33 1856.92 1715.37 1590.51 1478.82 1349.81 1232.04 1123.70 1023.39
33 2665.63 2426.92 2225.10 2050.27 1896.06 1758.12 1605.77 1466.69 1338.74 1220.28
32 3230.73 2933.36 2681.95 2464.17 2272.06 2100.23 1916.82 1749.39 1595.37 1452.76
31 3962.78 3585.59 3266.69 2990.44 2746.77 2528.80 2308.12 2106.66 1921.33 1749.74
30 4915.40 4431.65 4022.65 3668.35 3355.84 3076.30 2801.20 2550.06 2319.03 2105.13
29 6180.16 5548.66 5014.73 4552.22 4144.26 3779.32 3431.59 3114.13 2822.10 2551.72
28 7874.08 7035.10 6325.74 5711.27 5169.27 4684.43 4243.82 3841.57 3471.54 3128.95
27 10162.49 9029.08 8070.80 7240.70 6508.50 5853.53 5293.25 4781.75 4311.22 3875.57
26 13243.42 11702.63 10399.92 9271.46 8276.08 7385.69 6658.01 5993.68 5382.56 4816.75
25 17366.01 15270.67 13499.09 11964.48 10610.86 9400.00 8447.52 7577.98 6778.07 6037.48
24 22845.46 20023.30 17637.20 15570.26 13747.10 12116.22 10866.57 9725.72 8676.25 7704.59
23 30130.06 26367.98 23187.18 20431.85 18001.48 15827.43 14156.73 12631.50 11228.43 9929.38
22 39673.45 34712.87 30518.76 26885.65 23681.03 20814.39 18624.92 16626.08 14787.33 13084.91
21 51880.00 45447.42 40008.75 35297.56 31142.00 27424.72 24504.12 21837.82 19385.06 17114.16
20 68057.37 59623.21 52492.24 46315.10 40866.49 35992.53 32084.71 28517.14 25235.30 22196.79

HIS-06 temperature and humidity characteristic 15℃ ~24℃

Unit:KΩ
Relative
Temperature（℃）
humidity
%RH 15℃ 16℃ 17℃ 18℃ 19℃ 20℃ 21℃ 22℃ 23℃ 24
90 2.70 2.56 2.43 2.31 2.19 2.08 1.99 1.91 1.83 1.75
89 2.91 2.76 2.61 2.48 2.35 2.23 2.13 2.04 1.95 1.86
88 3.12 2.96 2.80 2.66 2.52 2.39 2.28 2.18 2.08 1.98
87 3.36 3.18 3.01 2.85 2.70 2.56 2.44 2.33 2.22 2.12
86 3.61 3.42 3.23 3.06 2.90 2.75 2.62 2.50 2.38 2.27
85 3.90 3.69 3.49 3.30 3.12 2.95 2.81 2.67 2.54 2.42
84 4.20 3.97 3.76 3.55 3.36 3.18 3.03 2.88 2.74 2.61
83 4.52 4.28 4.05 3.83 3.63 3.43 3.26 3.10 2.94 2.79
82 4.89 4.63 4.38 4.14 3.92 3.71 3.52 3.33 3.16 2.99
81 5.29 5.00 4.73 4.48 4.24 4.01 3.80 3.60 3.42 3.23
80 5.70 5.39 5.10 4.83 4.57 4.33 4.10 3.88 3.68 3.48
79 6.19 5.85 5.53 5.22 4.94 4.67 4.41 4.17 3.94 3.72
78 6.69 6.32 5.96 5.63 5.32 5.02 4.75 4.49 4.24 4.01
77 7.27 6.85 6.46 6.09 5.74 5.41 5.11 4.83 4.56 4.31
76 7.90 7.44 7.00 6.59 6.20 5.83 5.51 5.21 4.92 4.65
75 8.60 8.08 7.60 7.14 6.71 6.30 5.95 5.62 5.30 4.99
74 9.40 8.82 8.28 7.77 7.29 6.83 6.45 6.09 5.74 5.41
73 10.02 9.44 8.89 8.38 7.89 7.43 7.01 6.60 6.21 5.84
72 11.10 10.43 9.79 9.19 8.63 8.09 7.62 7.17 6.74 6.33
71 12.10 11.36 10.67 10.02 9.40 8.82 8.31 7.82 7.36 6.92
70 13.36 12.52 11.72 10.98 10.27 9.60 9.03 8.49 7.97 7.48
69 14.60 13.67 12.79 11.97 11.19 10.45 9.82 9.23 8.66 8.11
68 16.00 14.96 13.99 13.07 12.20 11.37 10.68 10.02 9.39 8.78
67 17.50 16.35 15.27 14.26 13.30 12.39 11.61 10.86 10.15 9.47
66 19.00 17.76 16.60 15.51 14.47 13.49 12.64 11.83 11.05 10.31
65 21.00 19.59 18.26 17.01 15.82 14.70 13.76 12.86 12.01 11.19
64 23.00 21.43 19.96 18.57 17.25 16.00 14.98 14.00 13.06 12.16
63 25.10 23.38 21.77 20.24 18.80 17.44 16.31 15.24 14.22 13.24
62 27.60 25.66 23.84 22.13 20.51 18.97 17.73 16.55 15.42 14.34
61 30.33 28.17 26.14 24.23 22.42 20.71 19.37 18.10 16.88 15.72
60 33.47 31.05 28.78 26.64 24.62 22.70 21.24 19.84 18.50 17.23
59 37.00 34.31 31.77 29.39 27.13 24.99 23.37 21.83 20.36 18.95
58 41.00 38.00 35.18 32.52 30.00 27.61 25.82 24.11 22.47 20.90
57 45.30 41.99 38.88 35.95 33.18 30.54 28.59 26.72 24.94 23.24

62 Maintenance
 Service Manual

56 50.20 46.55 43.12 39.89 36.83 33.93 31.76 29.69 27.71 25.82
55 56.00 51.92 48.08 44.47 41.05 37.80 35.35 33.02 30.79 28.65
54 62.80 58.20 53.88 49.80 45.95 42.29 39.51 36.87 34.34 31.92
53 70.00 64.95 60.21 55.74 51.51 47.50 44.33 41.31 38.42 35.65
52 78.80 73.12 67.79 62.76 58.00 53.49 49.86 46.40 43.10 39.94
51 88.00 81.79 75.97 70.47 65.27 60.34 56.11 52.08 48.23 44.54
50 99.10 92.12 85.57 79.39 73.55 68.00 63.15 58.52 54.10 49.86
49 111.00 103.28 96.04 89.20 82.74 76.61 70.94 65.54 60.38 55.44
48 126.20 117.27 108.88 100.97 93.48 86.38 79.89 73.71 67.79 62.13
47 142.60 132.48 122.97 114.00 105.52 97.48 90.16 83.18 76.51 70.12
46 162.00 150.38 139.46 129.16 119.43 110.19 101.62 93.45 85.64 78.17
45 185.00 171.49 158.81 146.85 135.53 124.80 115.00 105.66 96.74 88.20
44 212.00 196.23 181.41 167.45 154.23 141.70 130.18 119.19 108.69 98.64
43 243.00 224.65 207.41 191.15 175.78 161.19 148.03 135.48 123.49 112.01
42 280.00 258.38 238.08 218.93 200.82 183.64 168.64 154.32 140.65 127.56
41 324.00 298.37 274.29 251.59 230.12 209.75 192.53 176.11 160.43 145.41
40 375.30 344.95 316.43 289.55 264.12 240.00 220.30 201.52 183.57 166.39
39 431.00 395.97 363.07 332.05 302.71 274.87 251.94 230.08 209.19 189.19
38 500.00 458.51 419.54 382.80 348.04 315.07 289.04 264.21 240.49 217.78
37 580.00 531.11 485.18 441.88 400.92 362.06 332.09 303.52 276.21 250.07
36 676.00 618.14 563.79 512.55 464.08 418.09 383.52 350.57 319.07 288.92
35 790.00 721.80 657.74 597.34 540.20 486.00 445.77 407.41 370.75 335.66
34 930.00 848.96 772.84 701.08 633.19 568.78 521.38 476.19 433.01 391.66
33 1110.00 1011.10 918.19 830.60 747.75 669.14 613.58 560.59 509.97 461.49
32 1320.00 1201.45 1090.09 985.09 885.78 791.56 725.62 662.75 602.68 545.17
31 1590.00 1444.80 1308.40 1179.80 1058.15 942.75 863.43 787.81 715.55 646.36
30 1906.00 1731.91 1568.38 1414.20 1268.36 1130.00 1034.60 943.64 856.73 773.51
29 2300.00 2089.81 1892.37 1706.22 1530.13 1363.08 1244.55 1131.54 1023.56 920.17
28 2810.00 2550.31 2306.37 2076.38 1858.82 1652.43 1505.84 1366.07 1232.52 1104.65
27 3470.00 3144.23 2838.22 2549.70 2276.79 2017.87 1836.86 1664.27 1499.35 1341.45
26 4290.00 3885.50 3505.53 3147.28 2808.41 2486.92 2253.64 2031.21 1818.67 1615.18
25 5348.00 4843.01 4368.65 3921.40 3498.35 3097.00 2802.48 2521.66 2253.33 1996.42
24 6800.00 6152.28 5543.84 4970.19 4427.56 3912.77 3538.27 3181.20 2840.01 2513.33
23 8720.00 7888.61 7107.64 6371.32 5674.82 5014.05 4529.95 4068.38 3627.32 3205.04
22 11500.00 10371.38 9311.21 8311.65 7366.14 6469.15 5839.63 5239.39 4665.85 4116.71
21 15000.00 13512.80 12115.79 10798.65 9552.74 8370.76 7546.29 6760.17 6009.01 5289.82
20 19368.00 17441.37 15631.58 13925.26 12311.23 10780.00 9716.41 8702.31 7733.29 6805.52

HIS-06 temperature and humidity characteristic 25℃～ 34℃

Unit:KΩ
Relative
Temperature（℃）
humidity
%RH 25℃ 26℃ 27℃ 28℃ 29℃ 30℃ 31℃ 32℃ 33℃ 34℃
90 1.68 1.62 1.57 1.52 1.47 1.42 1.37 1.33 1.28 1.24
89 1.78 1.72 1.66 1.61 1.55 1.50 1.45 1.40 1.36 1.31
88 1.89 1.83 1.76 1.70 1.65 1.59 1.54 1.49 1.44 1.39
87 2.02 1.95 1.88 1.81 1.74 1.68 1.63 1.57 1.52 1.47
86 2.16 2.08 2.00 1.93 1.85 1.78 1.72 1.66 1.61 1.55
85 2.30 2.21 2.13 2.05 1.97 1.89 1.82 1.76 1.70 1.64
84 2.48 2.38 2.28 2.19 2.10 2.01 1.94 1.87 1.80 1.73
83 2.65 2.54 2.43 2.33 2.24 2.14 2.06 1.98 1.91 1.83
82 2.83 2.71 2.60 2.49 2.38 2.28 2.19 2.11 2.02 1.94
81 3.06 2.93 2.80 2.67 2.55 2.44 2.34 2.24 2.15 2.06
80 3.28 3.14 3.00 2.86 2.73 2.60 2.49 2.38 2.28 2.18
79 3.51 3.35 3.20 3.05 2.91 2.78 2.65 2.54 2.42 2.31
78 3.78 3.61 3.44 3.28 3.12 2.97 2.83 2.70 2.57 2.45
77 4.06 3.87 3.69 3.51 3.34 3.17 3.03 2.88 2.74 2.61
76 4.38 4.17 3.97 3.77 3.58 3.40 3.23 3.07 2.92 2.77
75 4.70 4.47 4.25 4.04 3.84 3.64 3.46 3.28 3.11 2.94
74 5.09 4.83 4.59 4.35 4.12 3.90 3.70 3.51 3.32 3.14

Maintenance 63
 Service Manual

73 5.49 5.21 4.94 4.68 4.43 4.19 3.97 3.75 3.54 3.34
72 5.93 5.62 5.33 5.04 4.77 4.50 4.26 4.02 3.80 3.57
71 6.49 6.13 5.79 5.46 5.14 4.84 4.57 4.32 4.07 3.83
70 7.00 6.61 6.24 5.88 5.53 5.20 4.91 4.63 4.35 4.09
69 7.59 7.16 6.75 6.35 5.96 5.59 5.27 4.97 4.67 4.38
68 8.20 7.73 7.28 6.84 6.42 6.01 5.67 5.34 5.01 4.70
67 8.82 8.32 7.83 7.36 6.91 6.47 6.10 5.74 5.38 5.04
66 9.60 9.03 8.49 7.96 7.46 6.97 6.57 6.18 5.80 5.43
65 10.40 9.78 9.18 8.61 8.06 7.52 7.08 6.65 6.24 5.84
64 11.30 10.62 9.96 9.33 8.72 8.13 7.65 7.19 6.74 6.30
63 12.30 11.55 10.82 10.12 9.45 8.80 8.27 7.75 7.26 6.78
62 13.30 12.49 11.71 10.96 10.23 9.53 8.96 8.41 7.87 7.35
61 14.60 13.69 12.81 11.97 11.15 10.36 9.73 9.12 8.53 7.96
60 16.00 14.99 14.02 13.08 12.17 11.30 10.61 9.94 9.29 8.66
59 17.60 16.48 15.40 14.35 13.35 12.38 11.61 10.87 10.15 9.46
58 19.40 18.15 16.95 15.79 14.68 13.60 12.75 11.93 11.13 10.36
57 21.60 20.18 18.81 17.49 16.22 14.99 14.05 13.14 12.26 11.41
56 24.00 22.40 20.86 19.37 17.94 16.55 15.50 14.48 13.50 12.54
55 26.60 24.81 23.10 21.44 19.84 18.30 17.13 16.00 14.90 13.83
54 29.60 27.59 25.66 23.81 22.01 20.28 18.96 17.69 16.46 15.26
53 33.00 30.74 28.57 26.48 24.46 22.52 21.04 19.62 18.24 16.90
52 36.90 34.35 31.90 29.53 27.25 25.05 23.38 21.77 20.21 18.69
51 41.00 38.18 35.47 32.86 30.34 27.90 26.03 24.22 22.46 20.76
50 45.80 42.62 39.55 36.60 33.75 31.00 28.91 26.89 24.93 23.03
49 50.70 47.20 43.83 40.59 37.45 34.43 32.08 29.81 27.61 25.47
48 56.70 52.72 48.90 45.21 41.66 38.22 35.62 33.10 30.67 28.30
47 64.00 59.37 54.91 50.61 46.46 42.46 39.57 36.78 34.07 31.45
46 71.00 65.89 60.97 56.22 51.65 47.23 43.99 40.85 37.81 34.86
45 80.00 74.13 68.48 63.03 57.78 52.70 49.02 45.46 42.00 38.65
44 89.00 82.54 76.32 70.33 64.54 58.96 54.75 50.69 46.74 42.92
43 101.00 93.48 86.25 79.28 72.55 66.06 61.28 56.65 52.17 47.82
42 115.00 106.23 97.79 89.66 81.81 74.23 68.69 63.33 58.14 53.10
41 131.00 120.81 111.01 101.56 92.44 83.64 77.33 71.23 65.31 59.57
40 149.90 138.01 126.56 115.53 104.88 94.60 87.37 80.37 73.58 66.99
39 170.00 156.52 143.54 131.04 118.97 107.32 99.08 91.11 83.38 75.88
38 196.00 180.09 164.79 150.04 135.81 122.06 112.71 103.65 94.88 86.37
37 225.00 206.61 188.92 171.87 155.41 139.52 128.86 118.54 108.53 98.82
36 260.00 238.50 217.80 197.86 178.62 160.04 147.90 136.16 124.77 113.73
35 302.00 276.83 252.61 229.27 206.76 185.00 170.96 157.37 144.19 131.41
34 352.00 322.66 294.42 267.21 240.96 215.59 199.30 183.53 168.24 153.40
33 415.00 380.13 346.58 314.24 283.04 252.90 233.57 214.84 196.70 179.09
32 490.00 448.82 409.19 371.01 334.16 298.57 275.69 253.53 232.06 211.23
31 580.00 531.32 484.48 439.35 395.79 353.72 326.76 300.66 275.37 250.83
30 693.69 634.81 578.16 523.57 470.89 420.00 387.67 356.36 326.02 296.58
29 821.00 751.60 684.82 620.48 558.38 498.40 459.39 421.61 385.00 349.49
28 982.00 898.01 817.20 739.32 664.18 591.58 544.87 499.65 455.82 413.29
27 1190.00 1085.85 985.63 889.06 795.87 705.85 649.51 594.96 542.09 490.80
26 1420.00 1297.43 1179.49 1065.83 956.17 850.22 781.68 715.32 651.00 588.59
25 1750.00 1597.27 1450.30 1308.67 1172.02 1040.00 954.91 872.53 792.68 715.22
24 2200.00 2005.83 1818.99 1638.94 1465.21 1297.38 1189.66 1085.37 984.29 886.22
23 2800.00 2551.47 2312.32 2081.87 1859.50 1644.68 1506.06 1371.84 1241.75 1115.55
22 3590.00 3270.74 2963.54 2667.51 2381.86 2105.90 1925.97 1751.75 1582.89 1419.07
21 4600.00 4191.56 3798.54 3419.81 3054.38 2701.33 2467.06 2240.24 2020.39 1807.10
20 5915.63 5385.23 4874.84 4383.03 3908.47 3450.00 3152.84 2865.12 2586.25 2315.70

64 Maintenance
 Service Manual

HIS-06 Characteristic of temperature and humidity 35℃ ~ 45℃

Unit:KΩ
Relative
Temperature（℃）
humidity
%RH 35℃ 36℃ 37℃ 38℃ 39℃ 40℃ 41℃ 42℃ 43℃ 44℃ 45℃
90 1.20 1.17 1.14 1.11 1.08 1.05 1.02 1.00 0.98 0.95 0.93
89 1.27 1.23 1.20 1.16 1.13 1.10 1.07 1.05 1.02 1.00 0.97
88 1.34 1.30 1.26 1.22 1.19 1.15 1.12 1.09 1.07 1.04 1.02
87 1.42 1.37 1.33 1.29 1.25 1.21 1.18 1.15 1.12 1.09 1.06
86 1.50 1.45 1.40 1.36 1.31 1.27 1.24 1.20 1.17 1.14 1.11
85 1.58 1.53 1.48 1.43 1.38 1.33 1.29 1.26 1.23 1.19 1.16
84 1.67 1.61 1.56 1.50 1.45 1.40 1.36 1.32 1.29 1.25 1.21
83 1.76 1.70 1.64 1.58 1.52 1.47 1.43 1.39 1.35 1.31 1.27
82 1.86 1.79 1.73 1.66 1.60 1.54 1.50 1.45 1.41 1.37 1.33
81 1.97 1.90 1.82 1.75 1.69 1.62 1.57 1.53 1.48 1.44 1.40
80 2.08 2.00 1.93 1.85 1.78 1.71 1.66 1.61 1.56 1.51 1.46
79 2.20 2.12 2.03 1.95 1.88 1.80 1.74 1.69 1.64 1.59 1.54
78 2.33 2.24 2.15 2.07 1.98 1.90 1.84 1.78 1.72 1.67 1.61
77 2.48 2.38 2.28 2.18 2.09 2.00 1.94 1.87 1.81 1.75 1.69
76 2.62 2.51 2.41 2.31 2.21 2.12 2.05 1.98 1.91 1.84 1.78
75 2.78 2.67 2.56 2.45 2.34 2.24 2.16 2.09 2.01 1.94 1.87
74 2.96 2.84 2.71 2.60 2.48 2.37 2.29 2.20 2.12 2.04 1.97
73 3.14 3.01 2.88 2.75 2.63 2.51 2.42 2.33 2.24 2.15 2.07
72 3.36 3.21 3.06 2.92 2.78 2.65 2.55 2.46 2.36 2.27 2.18
71 3.60 3.44 3.28 3.12 2.97 2.82 2.71 2.61 2.50 2.40 2.30
70 3.83 3.65 3.48 3.32 3.16 3.00 2.88 2.77 2.65 2.54 2.43
69 4.10 3.91 3.73 3.55 3.37 3.20 3.07 2.94 2.82 2.70 2.58
68 4.40 4.19 3.99 3.79 3.60 3.41 3.27 3.13 2.99 2.86 2.73
67 4.71 4.49 4.27 4.06 3.85 3.65 3.49 3.34 3.19 3.05 2.90
66 5.08 4.83 4.59 4.36 4.13 3.91 3.74 3.57 3.41 3.25 3.09
65 5.45 5.19 4.93 4.68 4.44 4.20 4.01 3.83 3.65 3.47 3.30
64 5.88 5.59 5.31 5.04 4.78 4.52 4.31 4.11 3.91 3.72 3.53
63 6.31 6.00 5.70 5.41 5.13 4.85 4.63 4.41 4.20 4.00 3.80
62 6.84 6.50 6.17 5.84 5.53 5.22 4.98 4.75 4.52 4.30 4.09
61 7.40 7.03 6.66 6.31 5.97 5.63 5.37 5.12 4.88 4.64 4.41
60 8.05 7.64 7.24 6.86 6.48 6.11 5.83 5.55 5.28 5.01 4.76
59 8.78 8.33 7.89 7.46 7.05 6.64 6.33 6.02 5.72 5.43 5.14
58 9.61 9.10 8.61 8.13 7.66 7.20 6.86 6.52 6.19 5.87 5.56
57 10.58 10.00 9.43 8.88 8.34 7.82 7.44 7.08 6.72 6.36 6.02
56 11.61 10.96 10.33 9.71 9.11 8.53 8.11 7.70 7.30 6.91 6.53
55 12.80 12.07 11.36 10.68 10.00 9.35 8.88 8.42 7.97 7.53 7.10
54 14.10 13.29 12.50 11.73 10.98 10.25 9.72 9.21 8.70 8.21 7.73
53 15.60 14.68 13.78 12.90 12.05 11.22 10.63 10.06 9.50 8.96 8.42
52 17.22 16.18 15.18 14.20 13.24 12.31 11.66 11.02 10.40 9.79 9.19
51 19.10 17.93 16.79 15.68 14.59 13.54 12.81 12.10 11.40 10.72 10.05
50 21.18 19.87 18.60 17.36 16.15 14.97 14.14 13.33 12.54 11.77 11.01
49 23.40 21.97 20.57 19.21 17.89 16.60 15.65 14.73 13.82 12.94 12.08
48 26.00 24.35 22.75 21.20 19.68 18.20 17.17 16.16 15.18 14.21 13.27
47 28.90 27.06 25.28 23.54 21.85 20.20 19.03 17.88 16.77 15.68 14.61
46 32.00 29.95 27.96 26.03 24.14 22.30 21.00 19.74 18.50 17.29 16.11
45 35.40 33.16 30.99 28.87 26.81 24.80 23.33 21.90 20.50 19.14 17.80
44 39.20 36.71 34.29 31.93 29.64 27.40 25.79 24.21 22.67 21.17 19.70
43 43.60 40.77 38.02 35.35 32.74 30.20 28.45 26.73 25.06 23.43 21.83
42 48.20 45.06 42.00 39.02 36.13 33.30 31.40 29.55 27.74 25.97 24.25
41 54.00 50.43 46.97 43.59 40.30 37.10 34.98 32.92 30.90 28.93 27.00
40 60.60 56.63 52.78 49.02 45.36 41.80 39.36 36.98 34.66 32.39 30.17
39 68.60 64.04 59.61 55.30 51.10 47.00 44.23 41.53 38.89 36.31 33.78
38 78.10 72.70 67.45 62.33 57.35 52.50 49.44 46.45 43.54 40.69 37.90

Maintenance 65
 Service Manual

37 89.40 82.99 76.75 70.68 64.76 59.00 55.58 52.24 48.98 45.80 42.68
36 103.00 95.43 88.06 80.89 73.91 67.10 63.17 59.33 55.59 51.93 48.35
35 119.00 110.35 101.94 93.75 85.77 78.00 73.18 68.47 63.88 59.39 55.00
34 139.00 129.32 119.90 110.73 101.80 93.10 86.80 80.66 74.66 68.80 63.07
33 162.00 149.97 138.28 126.90 115.81 105.00 98.24 91.63 85.19 78.89 72.73
32 191.00 176.44 162.29 148.50 135.08 122.00 114.10 106.40 98.87 91.52 84.34
31 227.00 209.28 192.04 175.27 158.93 143.00 133.62 124.46 115.52 106.79 98.25
30 268.00 247.75 228.05 208.88 190.20 172.00 160.04 148.37 136.97 125.83 114.95
29 315.00 291.16 267.97 245.41 223.43 202.00 187.96 174.26 160.88 147.81 135.03
28 372.00 342.25 313.32 285.16 257.73 231.00 215.94 201.25 186.90 172.88 159.17
27 441.00 404.50 369.01 334.45 300.80 268.00 251.39 235.18 219.35 203.88 188.76
26 528.00 484.54 442.27 401.13 361.06 322.00 301.66 281.81 262.43 243.49 224.98
25 640.00 590.21 541.79 494.65 448.75 404.00 375.91 348.49 321.72 295.57 270.00
24 791.00 735.73 681.97 629.64 578.68 529.00 486.67 445.36 405.02 365.60 327.08
23 993.00 926.97 862.74 800.23 739.35 680.00 621.22 563.85 507.84 453.11 399.61
22 1260.00 1171.18 1084.80 1000.72 918.82 839.00 766.05 694.86 625.34 557.42 491.03
21 1600.00 1476.79 1356.97 1240.33 1126.73 1016.00 929.53 845.14 762.74 682.23 603.53
20 2053.00 1880.43 1712.58 1549.22 1390.09 1235.00 1131.26 1030.03 931.17 834.59 740.18

66 Maintenance
 JF00302871

GREE ELECTRIC APPLIANCES,INC.OF ZHUHAI

Add: West Jinji Rd, Qianshan, Zhuhai, Guangdong, China, 519070
Tel: (+86-756) 8522218 Fax: (+86-756) 8669426
E-mail: [email protected] Http://www.gree.com

HONG KONG GREE ELECTRIC APPLIANCES SALES LIMITED

Add: Unit 2612,26/F.,Miramar Tower 132 Nathan Road,TST,Kowloon,HK
Tel: (852) 31658898 Fax: (852) 31651029

For product improvement, specifications and appearance in this manual are subject to change without prior notice.