Manuals+ — User Manuals Simplified.

EUREKA FORBES Aquaguard Regal RO MC Water Purifier

User Manual

Home » EUREKA FORBES » EUREKA FORBES Aquaguard Regal RO MC Water Purifier User Manual

EUREKA FORBES Aquaguard Regal RO MC Water Purifier

 Contents
1 WHY CHOOSE AQUAGUARD®?
2 INSTALLING YOUR AQUAGUARD® REGAL
2.1 Input water quality usage limitations:
3 HERE’S HOW YOUR AQUAGUARD® REGAL UV+UF WORKS
4 PURIFICATION PROCESS AQUAGUARD® REGAL UV+UF
5 LED INDICATION CHART FOR AQUAGUARD® REGAL UV+UF
6 AQUAGUARD® REGAL UV+UF TECHNICAL SPECIFICATIONS*
7 HERE’S HOW YOUR AQUAGUARD® REGAL RO WORKS
8 PURIFICATION PROCESS IN YOUR AQUAGUARD® REGAL RO
9 AQUAGUARD® REGAL RO TECHNICAL SPECIFICATIONS*
10 LED INDICATION CHART FOR AQUAGUARD® REGAL RO
11 HERE’S HOW YOUR AQUAGUARD® REGAL RO+UV+MTDS WORKS
12 PURIFICATION PROCESS IN YOUR AQUAGUARD® REGAL
RO+UV+MTDS
13 LED INDICATION CHART FOR AQUAGUARD® REGAL RO+UV+MTDS
14 AQUAGUARD® REGAL UV+UF TECHNICAL SPECIFICATIONS*
15 CARTRIDGE LIFE”
16 A QUICK CHECKLIST
17 CLEANING AND DISINFECTION OF WATER STORAGE TANK
18 TIPS FOR SAFETY AND MAINTENANCE OF YOUR AQUAGUARD®
19 WARRANTY TERMS & CONDITIONS
19.1 Post-warranty
20 Documents / Resources
21 Related Posts

WHY CHOOSE AQUAGUARD®?

Only Aquaguard®

Has the trust of over 15 million mothers*

Is owned by over 1.62 lakh doctors
Has service with 5 kms. range of wherever you are
Has over 21 different technologies to address 21 different water conditions across the country
Is certified by over 130 leading national and international laboratories
Is sold in over 35 countries worldwide

*As per Superbrands & Reader’s Digest.

INSTALLING YOUR AQUAGUARD® REGAL

Make sure that your Aquaguard® Regal is installed by a trained Eureka Forbes Service Technician only.

1. Input water must be tested for Total Dissolved Solids (TDS) and Total Hardness.
2. Install your Aquaguard® Regal in a dry ventilated place.
– Keep it away from direct sunlight, heating devices or areas below freezing temperatures.
– You can keep it on the kitchen counter or wall-mount it.
– The purifier should be placed in area which is free of ants/insects/other pests.
3. Ensure that the input tap water temperature is in the range of 10º-40ºC.
– Avoid installation to a hot water tap as it can damage the filters
4. Ensure that the input water pressure for Regal RO+UV+MTDS / RO are from 0.3 kg/cm2
– 3.0 kg/cm2 and Regal UV+UF is from 0.3 kg/cm2
– 2.0 kg/cm2 .If the input water pressure is more than specified, installation of a PRV (Pressure Reducing
Valve)** is mandatory. If the input water pressure is less than specified, installation of a booster pump** is
recommended.
5. Flush filter thoroughly and independently for 3-5 minutes to remove fine particles present in the filter. This
should be done before installation of the unit.
6. After installing, run the purifier for 5-10 minutes and drain this water.

Input water quality usage limitations:

1. If the input water iron content is more than 0.3 mg/litre, use of an iron remover** is recommended as a pre-
treatment.
2. If the input water turbidity is more than 5 NTU or comprises colloidal particles, use of a special filter** is
required as a pre-filter.
3. If the input water TDS is more than 1000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use
of a Membrane life enhancer** is recommended.
4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications.

**Available at an extra cost.

MTDS REGULATOR OPERATING PROCEDURE: (Only Applicable for RO+UV+MTDS models)

TDS modulator is located inside the product. As per factory setting, it comes in fully closed mode. TDS level of
output water can be increased by slowly loosening the spindle of the TDS modulator (anticlockwise). Normally a
slight quarter turn is enough to increase the TDS of the output water. Rotating the spindle in the clockwise
direction closes the TDS modulator and reduces the level of TDS blending.

Please note that the TDS blending, and its adjustment is dependent upon the level of TDS of input water and on
the TDS reduction capacity of the RO membrane. TDS adjustment should be done by the authorized Eureka
Forbes technician only

HERE’S HOW YOUR AQUAGUARD® REGAL UV+UF WORKS

PURIFICATION PROCESS AQUAGUARD® REGAL UV+UF

Strag
Treatment Material Banefits
e

Multi-layered Polyprop
Removes fine suspended particles such as dust, dirt, mud
1. i-Filter™ ylene roving wound ca
and sand from water.
rtridge

Chemi-Block (wi Dust Free Reduces excess chlorine, bad odour, colour and organic i
2. th built-in Particl Bacteriostatic Activate mpurities. It also removes very fine turbidity causing partic
e Trap Filter™) d Carbon Block les.

Capillary tube type membrane-based technology that imp

3. Ultra Filter UF Hollow Fiber arts crystal clear clarity to drinking water in addition to
making the water safe from bacteriological contamination.

UV disinfects the water by eliminating waterborne

4. UV e-boiling Germicidal UV Lamp disease-causing bacteria, viruses and protozoa, thereby
making it safe to drink.

Instantly charges purified water with essential micro-nutrie

Mineral Charge Calcium & Magnesium
5. nts like Calcium & Magnesium which enhance the taste of
Cartridge Enriched Water
water & makes it healthier for consumption.

LED INDICATION CHART FOR AQUAGUARD® REGAL UV+UF

AQUAGUARD® REGAL UV+UF TECHNICAL SPECIFICATIONS*

# Technical Parameters Specifications

1 Model Aquaguard® Regal UV+UF

PRODUCT SPECIFICATION

1 Dimension (W X D X H) 320 mm X 275mm X 476 mm

2 Net Weight 4.5 kg (Approx.)

3 Purification Technology UV+UF

4 Tank Capacity 6.2 Litres (approx.)

i-Filter™, Chemi-Block, UF Filter, UV e-boiling, Mineral Charge Car

5 Standard Filtration Supplied
tridge

ELECTRICAL SPECIFICATIONS
 1 Power Rating 20 Watts (Max.)

2 Power Supply Input 230VAC, 50Hz. Output: 12V.(ON Board AC -DC)

3 UV Lamp 11 Watts

4 UV Lamp Life 8000 burning hours (as per manufacturer’s spec.)

5 Operating Voltage Range 150 VAC to 250 VAC, 50 Hz

RECOMMENDED INPUT WATER PARAMETERS

1 Input Water Pressure Range** 0.3 to 2.0 kg/cm2

2 Input Iron (Max.) 0.3 mg/L

3 Input Chlorine Content (Max.) 0.2 mg/L

4 Input Water Turbidity (Max.) 5 NTU

Total Dissolved Solids (TDS) (m

5 Up to 200 mg/L
ax.)

6 Input Water Temperature 10°C to 40°C

*Technical Specifications are subject to change without prior notice.

Note: SMPS is designed to operate from 150VAC to 280VAC.
Note: The performance data presented in the table is applicable under standard laboratory conditions# .
Actual performance may vary depending on the input water quality, water pressure and condition of filters. Input
water quality/pressure/TDS are important determinants of recovery rate and rejection. **If the input water pressure
is more than 2.0 kg/cm2 , installation of a PRV (Pressure Reducing Valve) is mandatory. If the input water
pressure is less than 0.3 kg/cm2 , installation of a booster pump is recommended. These accessories are
available at an extra cost.

Warranty void if not installed as per recommendations.

# Standard Test Conditions:
Feed Water Quality: TDS Max: 200 mg/L
Pressure: 1 kg/cm2 , Turbidity: 1 NTU (Max.), Temperature: 25°C, Chlorine: below 0.2 mg/L, Iron: below 0.3 mg/L,
Life: 6000 liters
HERE’S HOW YOUR AQUAGUARD® REGAL RO WORKS

PURIFICATION PROCESS IN YOUR AQUAGUARD® REGAL RO

Strag
Treatment Material Banefits
e

Multi-layered Polyprop
Removes fine suspended particles such as dust, dirt, mu
1. i-Filter™ ylene roving wound ca
d and sand from water.
rtridge

Chemi-Block (wit Dust Free Bacteriostati Reduces excess chlorine, bad odour, colour and organic
2. h built-in Particle c Activated Carbon Blo impurities. It also removes very fine turbidity causing part
Trap Filter™) ck icles.

Membrane Prevents scaling of dissolved salts on the surface of the

Special anti-scalant m
3. membrane, thereby enhancing the membrane life and pe
Life Enhancer*** edia
rformance.

Thin Film composite ( Reduces TDS, hardness, pesticides and heavy metals lik
Reverse Osmosis
4. TFC) reverse osmosis e arsenic, lead and mercury. Eliminates microorganisms l
Cartridge
membrane ike bacteria, viruses, protozoa and cysts.

Instantly charges purified water with essential

Mineral Charge C Calcium & Magnesium
5. micronutrients like Calcium & Magnesium which enhance
artridge Enriched Water
the taste of water & makes it healthier for consumption.

***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1000
ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost

AQUAGUARD® REGAL RO TECHNICAL SPECIFICATIONS*

 # Technical Parameters Specifications

1 Model Aquaguard® Regal RO

PRODUCT SPECIFICATION

1 Dimension (W X D X H) 320 mm X 275 mm X 476 mm

2 Net weight 6.2 kg (Approx.)

3 Purification Technology RO

4 Tank Capacity 6.2 Litres (approx.)

i-Filter™, Chemi Block, Reverse Osmosis Membrane, Mineral

5 Standard Filtration supplied
charge cartridge.

ELECTRICAL SPECIFICATIONS

1 Power Rating 35 Watts (Max.)

Input 230V AC, 50Hz./Output (internal AC/DC Adaptor) 24V DC, 2.

2 Power Supply
5A

3 Operating Voltage Range 150 VAC to 250 VAC, 50 Hz

RECOMMENDED INPUT WATER PARAMETERS

1 Input Water Pressure Range** 0.3 to 3 kg/cm2

2 Input Iron (Max.) 0.3 mg/L

3 Input Chlorine Content (Max.) 0.2 mg/L

4 Input Water Turbidity (Max.) 5 NTU

Total Dissolved Solids (TDS) (ma

5 Up to 2000 mg/L ++
x.)

6 Input Water Temperature 10°C to 40°C

7 Total Hardness 600 mg/L

* Technical Specifications are subject to change without prior notice.

Note: SMPS is designed to operate from 150VAC to 280VAC.
Note: The performance data presented in the table is applicable under standard laboratory conditions# .Actual
performance may vary depending on the input water quality, water pressure, turbidity and condition of filters. Input
water quality/pressure/TDS are important determinants of recovery rate and rejection. **If the input water pressure
is more than 3.0 kg/cm2 , installation of a PRV (Pressure Reducing Valve) is mandatory. If the input water
pressure is less than 0.3 kg/cm2 , installation of a booster pump is recommended. If the input water TDS is more
than 1000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer is
recommended.
These accessories are available at an extra cost.

Warranty void if not installed as per recommendations.

#Standard Test Conditions:
Feed Water Quality: TDS Max: 1000 mg/L with NaCl
Pressure: 1 kg/cm2 , Turbidity: 1 NTU (Max.), Temperature: 25°C, Chlorine: below 0.2 mg/L,
Iron: below 0.3 mg/L Life: 6000 liters, Pressure on membrane: 75 psi, Product recovery @ 25%

LED INDICATION CHART FOR AQUAGUARD® REGAL RO

HERE’S HOW YOUR AQUAGUARD® REGAL RO+UV+MTDS WORKS

PURIFICATION PROCESS IN YOUR AQUAGUARD® REGAL RO+UV+MTDS

***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1000
ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost.

LED INDICATION CHART FOR AQUAGUARD® REGAL RO+UV+MTDS

AQUAGUARD® REGAL UV+UF TECHNICAL SPECIFICATIONS*

# Technical Parameters Specifications

1 Model Aquaguard® Regal RO+UV+MTDS

PRODUCT SPECIFICATION

1 Dimension (W X D X H) 320 mm X 275 mm X 476 mm

Net weight 7 kg (Approx.)

2

3 Purification Technology RO+UV+MTDS

4 Tank Capacity 6.2 Litres (approx.)

 i-Filter™, Chemi-Block, Reverse Osmosis Membrane, UV e-boilin
5 Standard Filtration supplied
g, Mineral charge cartridge, TDS regulator

ELECTRICAL SPECIFICATIONS

1 Power Rating 40 Watts (Max.)

2 Power Supply Input 230 VAC, 50Hz and Output: 24V (On board AC-DC)

3 UV Lamp 4 Watts

4 UV Lamp Life 5000 burning hours (as per UV lamp manufacturer spec.)

5 Operating Voltage Range 150 VAC to 250 VAC, 50 Hz

RECOMMENDED INPUT WATER PARAMETERS

1 Input Water Pressure Range** 0.3 to 3 kg/cm2

2 Input Iron (Max.) 0.3 mg/L

3 Input Chlorine Content (Max.) 0.2 mg/L

4 Input Water Turbidity (Max.) 5 NTU

Total Dissolved Solids (TDS) (ma

5 Up to 2000 mg/L++
x.)

6 Input Water Temperature 10°C to 40°C

7 Total Hardness 600 mg/L

*Technical Specifications are subject to change without prior notice.

Note: SMPS is designed to operate from 150VAC to 280VAC).
Note: The performance data presented in the table is applicable under standard laboratory
conditions# . Actual performance may vary depending on the input water quality, water pressure, turbidity and
condition of filters. Input water quality/pressure/TDS are important determinants of recovery rate and rejection.
**If the input water pressure is more than 3.0 kg/cm2 , installation of a PRV (Pressure Reducing Valve) is
mandatory. If the input water pressure is less than 0.3 kg/cm2 , installation of a booster pump is recommended. If
the input water TDS is more than 1000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a
Membrane life enhancer is recommended.
These accessories are available at an extra cost.

Warranty void if not installed as per recommendations.

#Standard Test Conditions:
Feed Water Quality: TDS Max: 1000 mg/L with NaCl
Pressure: 1 kg/cm2 , Turbidity: 1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/L, Iron: below 0.3 mg/L, Life:
6000 liters, Pressure on membrane : 75 psi, Product recovery @25%

CARTRIDGE LIFE”

For Aquaguard® Regal RO+UV+MTDS / RO / UV+UF (Refer model specific components)

Consumable Cartridges Average Service Life

i-Filter™ 6000# Litres

Chemi-Block 6000# Litres

Mineral Charge Cartridge 6000# Litres

UF Filter 6000# Litres

UV Lamp (11W) (UV+UF) 8000 burning hours**

UV Lamp (4W) (RO+UV+MTDS) 5000 burning hours**

RO membrane 6000# Litres

Note: Please refer Standard Test Conditions# for filter life.

**As per manufacturer’s spec.

A QUICK CHECKLIST
 Problems Checkpoints Solutions

1. Is the tank clean? 1. Clean the storage tank.

2. Have you kept the purified water 2. Dispose of water and clean the tank.
Water tastes bad 3. Call an authorised Eureka Forbes service technici
in the tank for too long?
3. Is it time to change the filter? an.

1. Is the tap water valve closed? 1. Open the tap water valve.
2. Is the tap water pressure too low 2. If so, the amount of purified water will be
Less water has be
? reduced.
en purified
3. Filters may be clogged or 3. Call an authorised Eureka Forbes service technici
damaged? an.

1. Is there water available in the ov

1. Ensure the overhead tank is filled with water.
Water doesn’t flow erhead tank?
2. Ensure the tap is open.
into the storage ta 2. Is the main water supply tap clos
nk 3. Call an authorised Eureka Forbes service technici
ed?
an.
3. Not sure what is wrong?

1. Close the tap water valve, unplug the power cord

1. Is water coming out of the top of
Water is leaking and call an authorised Eureka Forbes service tec
the purifier?
hnician.

CLEANING AND DISINFECTION OF WATER STORAGE TANK

Note: Storage Tank of this product must be periodically cleaned (at least once in every 30 days) by a disinfectant.
Disinfection Tablets may be purchased from the Company Authorised Service Centre. Please follow the
disinfection process strictly as per the instructions as provided in this User Manual.

Drain the tank completely.

Switch OFF the water purifier from the main power supply.
Open the top cover, wipe the inside of the tank with a dry, clean soft cloth.
Keep the top cover in place.
Switch the power supply ON.
Let the storage tank get filled & then drop one disinfection tablet* into the tank.
Caution: Keep the Disinfection Tablets out of the reach of children.
Do not eat / consume the tablet.
Keep the top cover in place & leave the unit for 30 min.
After 30 min. open the tap & discard this and the first filling water completely.
Now your unit is ready to use. In case you notice any medicinal taste/smell, discard the tank of water fully & let
it refill again.
 Please ensure that this disinfection process is carried out by the authorised installation
person/service technician during first installation and in every subsequent mandatory servicing of your product.

*Available with Eureka Forbes Service Technician

TIPS FOR SAFETY AND MAINTENANCE OF YOUR AQUAGUARD®

Read attentively and understand the purifier and its functions, before use.
Installation and service has to be conducted by authorised person from Eureka Forbes Limited only.
In case of any damage or incorrect functioning, immediately contact an authorised service centre of Eureka
Forbes Limited.
Water from waste water tube is not suitable for drinking. You can use that water for gardening or to clean floors
(For applicable models only).
Water storage tank must be periodically (at least once in every 30 days) cleaned using a disinfectant (For
applicable models only).
Drain the water if it hasn’t been used for over 48 hours.
Ensure that the flow restrictor is checked and replaced (if required), by the authorised service technician during
the mandatory service or in-service call (For applicable models only).
Ensure that the replacement of the consumable cartridges are done by a trained Eureka Forbes technician.
Ensure that the filter cartridges and spares used during service/replacement, are genuine and from Eureka
Forbes Limited only

WARRANTY TERMS & CONDITIONS

The goods are warranted against defects arising from faulty designs, workmanship and materials 12 months from
the date of installation or 15 months from the date of sale, whichever is earlier, subject to the following’s
conditions:

1. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its
authorised agent adequate opportunity to inspect test and remedy them for which the Customer will deposit the
goods at its own expense, if so required by the Company, with the Company’s Office/Service Centre along with
the original invoice in the city where they are sold
2. The Inspection and Test report of the Company’s Office Service Centre will be final and binding under the
Warranty for determining defects, repairs/alterations required or carried out or certifying work of the goods
thereafte
3. Aquaguard may require initial setting, post-installation, depending on varying water conditions and power
supply In case of any service requirement, post-installation, please contact the Company’s Service Centre
4. The Company or its authorised agent will be entitled to retain any defective part replaced under the Warranty
5. Not with standing anything to the contrary contained or implied by this Warranty:
a. The Company’s ability under this Warranty shall be limited to the first sale of the goods by the Company to
the Customer and will not apply or extend to any Secondary sale of goods by the Customer
b. The Company’s ability under this Warranty shall be limited only to defects in the goods which occur under
the conditions of normal operation of the goods and their proper and prescribed use. The Warranty does not
cover or extend to defects which are determined by the Company or is authorised agents as occurring or
 resulting from or attributable to negligence, abuse, misuse, faulty care, operation or maintenance or repairs,
alterations to the goods or any part thereof by others of the use of the goods on electrical supply for which they
are not designed or damage caused by lightning or other electrical disturbances or interruptions
c. The Company’s ability under this Warranty shall remain valid only if the goods are duly installed by the
Company or is authorised Agency at the location specified in the Invoice and such installation is undertaken by
the Company or authorised agent or franchisee
d. Consumable items like the I-Filter, Chemi-block, UF cartridge and Mineral Charge Cartridge that are subject
to normal wear and tear are not covered by this warranty
e. Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the
date of installation, on the condition that the input water is as per the standard test conditions* mentioned in the
user manual. If the RO membrane gets clogged within warranty period, it will be cleaned/ repaired/replaced
free of charge as deemed fit by the company authorised service person/centre after inspection (applicable for
RO models only)
f. The Customer will have no claim against the Company, its employees and its authorised agents or
franchisees under or pursuant to this Warranty in respect of death or injury to the Customer or any other
person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or
operation or utilization of the goods otherwise than in accordance with the User Guide or by or due to any other
cause or circumstances beyond the control of the Company
g. The Company’s liability, under this Warranty, shall in no event and under no circumstances exceed the price
paid by the Customer to the Company for the goods stated in the Invoice. General For purpose of this
Warranty, the following expressions shall have the following meanings respectively;

1. The Goods’ shall mean the goods described in the Order Form
2. ‘The Customer’ shall mean the original purchaser of the Goods from the Company
3. The Company shall mean EUREKA FORBES LIMITED
4. ‘General Terms and Conditions’ shall mean the terms and conditions agreed upon by the Customer and the
Company printed on the Order Form
5. ‘Invoice’ shall mean the invoice issued by the Company to theCustomer describing the goods and indicating,
Inter alia, the total purchase price thereof and name of the Customer
6. User Guide shall mean the instructions for installation, use and maintenance contained in the leaflet supplied
by the Company

Post-warranty

1. The Customer may be offered a yearly Service Contract at the prevailing Company rates and terms
2. In case the Customer does not wish to enter the Service Contract, he has the option of calling the Company’s
Service Centre and having his Aquaguard® serviced on an actual basis i.e. by paying the Labor cost and
Spares needed to attend to that Service/ Complaint Call at the prevailing Company rates Such service will be
rendered by the Company in towns/places where the Company has its Service Centers
3. If during such servicing it is necessary for the Company to replaceor repair defective components or parts, the
Customer shall be required to pay for the same as per the Company’s prevailing price list

*Conditions apply
 ✆ 18602661177
SMS ‘<REQ>’ to 80822 99333

Now buy online on eurekaforbes.com | www.facebook.com/EurekaForbes

www.twitter.com/EurekaForbes| Email: [email protected]

Eureka Forbes Limited: B1/B2, 701, 7th Floor, Marathon lnnova Marathon NextGen, Off Ganpatrao Kadam Marg,
Lower Parel, Mumbai – 400 013, India. Tel: +91 22 4882 1700, 6260 1888 • Fax: +91 22 4882 1701

Environment Protection:
“Protection” has always been our motto and guiding principle. We care for the environment. W
e urge you to recycle the packaging material or take it to the nearest recycling facility rather th
an dispose of it with the rest of your waste.
Your product has been designed to work for many years, however, should you wish to upgrade
or replace your old product, remember to help protect the environment by disposing of it at you
r local e-waste disposal centre. Should you have any queries, the nearest authorised service c
entre of Eureka Forbes will be able to guide you.
Allow us to become your environment partner; together we can make the world a cleaner
place

old logo and new logo are both original Aquaguard products from the house
of Eureka Forbes Limited.

Documents / Resources

EUREKA FORBES Aquaguard Regal RO MC Water Purifier [pdf] User Manual

Aquaguard Regal RO MC Water Purifier
Manuals+, home privacy