Optical Communication System

Datasheet

10G CWDM SFP+ 1270nm~1450nm 40km Transceiver for SMF

CWDM-SFP10G-40S

Features

• Hot-Pluggable SFP+ Footprint

• 10-Wavelengths CWDM DFB
Transmitter from 1270nm to 1450nm,
with step 20nm
• 14dB Power Budget
• Duplex LC connector
• Power Dissipation <1.2W
• Build-in digital diagnostic functions,
including optical power monitoring
• Commercial temperature range:
0°C to 70°C
• Compliant with SFP+ MSA
Specification SFF-8431
• Compliant with SFF-8472 MSA

Application

• 10GBASE-ER/EW 10G Ethernet

• 10GBASE-ER at 10.31Gbps
• 10GBASE-EW at 9.95Gbps
• OBSAI rates 6.144 Gb/s, 3.072 Gb/s,
1.536 Gb/s, 0.768Gb/s
• CPRI rates 9.830 Gb/s,7.373Gb/s,
6.144 Gb/s, 4.915 Gb/s, 2.458 Gb/s,
1.229 Gb/s, 0.614Gb/s
• Other optical links

1
 Optical Communication System

Datasheet

Description

The CWDM-SFP10G-40S series optical transceiver is designed for fiber communications

application such as 10G Ethernet, which fully compliant with the specification of SFP+
MSA SFF-8431.

This module is designed for single mode fiber and operates at a nominal wavelength of
CWDM wavelength. There are ten center wavelengths available from 1270nm to
1450nm, with each step 20nm. A guaranteed optical link budget of 14 dB is offered.

The module is with the SFP+ connector to allow hot plug capability. Single 3.3V power
supply is needed. The optical output can be disabled by LVTTL logic high-level input of
TX_DIS. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical
signal of receiver.

This module provides digital diagnostic functions via a 2-wire serial interface as defined
by the SFF-8472 specification.

Product Specifications

I. General Product Characteristics

Parameter Symbol Min Typ Max Units Ref.

Module Form Factor BR 9.95 10.5 Gb/s 1

Number of Lanes BER 10-12 2

Maximum Aggregate Data Rate Lmax 40 km

Notes:
1. 10GBASE-ER, 10GBASE-EW, 1200-SM-LL-L 10GFC.
2. Tested with a PRBS 231-1 test pattern.

2
 Copyright
Copyright
© 2009-2015
© 2009-2015
Fiberstore
Fiberstore

Optical Communication System

Datasheet

CWDM Wavelength
18 Wavelengths from 1270nm to 1610nm, each step 20nm.

Wavelength(nm)
Band Nomenclature
Min. Typ. Max.

A 1264 1270 1277.5

B 1284 1290 1297.5
O-band Original
C 1304 1310 1317.5
D 1324 1330 1337.5
E 1344 1350 1357.5
F 1364 1370 1377.5
G 1384 1390 1397.5

E-band Extended H 1404 1410 1417.5

I 1424 1430 1437.5
J 1444 1450 1457.5
K 1464 1470 1477.5
L 1484 1490 1497.5
S-band Short Wavelength
M 1504 1510 1517.5
N 1524 1530 1537.5
C-band Conventional O 1544 1550 1557.5
P 1564 1570 1577.5
L-band Long Wavelength
Q 1584 1590 1597.5
R 1604 1610 1617.5

Page 3+86
+86 of 4(755)
(755) 83008300 [email protected]
3611 [email protected]
3611 [email protected] 3 www.fiberstore.com
(755) 8300 3611 [email protected]
www.fiberstore.com
FSCOM www.fiberstore.com
 Copyright
Copyright
© 2009-2015
© 2009-2015
Fiberstore
Fiberstore

Optical Communication System

Datasheet

II. Absolute Maximum Ratings

Parameter Symbol Min Typ Max Unit

Maximum Supply Voltage 1 Vcc -0.5 4.0 V

Storage Temperature Ts -40 85 °C

Case Operating Temperature Tc 0 70 °C

Supply Voltage Vcc 3.13 3.3 3.45 V

Icc (0°C to
Supply Current 350 mA
70°C)

III. Electrical Characteristics

Parameter Symbol Min Typ Max Unit Notes

Transmitter

CML Inputs(Differential) Vin 150 1200 mVpp 1

Input Impedance
Zin 85 100 115 ohm
(Differential)
TX_DISABLE Input
2 Vcc+0.3 V
Voltage - High

TX_DISABLE Input
0 0.8 V
Voltage - Low

TX_FAULT Output
2 Vcc+0.3 V
Voltage - High

TX_FAULT Output
0 0.5 V
Voltage - Low

Page 4+86
+86 of 4(755)
(755) 83008300 +86 [email protected]
3611 [email protected]
3611 [email protected] 4www.fiberstore.com
(755) 8300 3611 [email protected]
www.fiberstore.com
FS.COM www.fiberstore.com
Page 4 of
6
 Optical Communication System

Datasheet

Receiver

CML Outputs (Differential) Vout 350 700 mVpp 1

Output Impedance (Differential) Zout 85 100 115 ohm

RX_LOS Output Voltage - High 2 Vcc+0.3 V

RX_LOS Output Voltage - Low 0 0.8 V

VoH 2.5 V
MOD_DEF ( 2:0 ) 2
VoL 0 0.5 V

Notes:
1. After internal AC coupling.
2. Reference the SFF-8472 MSA.

IV. Optical Characteristics

Parameter Symbol Min Type Max Unit Notes

Transmitter

Optical Wavelength λ λC-6 λC λC+7.5 nm 2

-20dB Spectrum Width Δλ 1 nm

Side Mode Suppression Ratio SMSR 30 dB

Output Opt. Pwr: 9/125 SMF Pout -1 +4 dBm 1

Optical Extinction Ratio ER 3.5 dB

Average Launch Power of
POFF -30 dBm
OFF Transmitter

5
 Optical Communication System

Datasheet

Signaling Speed per Lane 10.5 GBd 1

Transmitter Dispersion Penalty TDP 2 dB

Receiver

Receiver Sensitivity @ 10.5Gb/s Pmin -15 dBm 3

Maximum Input Power Pmax -0.5 dBm

Optical Center Wavelength λ 1260 1420 nm

Receiver Reflectance Rrf -27 dB

LOS De-Assert LOSD -16 dBm

LOS Assert LOSA -28 dBm

LOS Hysteresis 1 dB

Notes:
1. Output power is coupled into a 9/125µm SMF.
2. ITU-T G.694.2 CWDM wavelength from 1270nm to 1450nm, each step 20nm.
3. Average received power; BER less than 1E-12 and PRBS 231-1 test pattern.

6
 Optical Communication System

Datasheet

V. Pin Description

BOTTOM OF TOP VIEW

Towad BOARD AS OF
VIEWED FROM BOARD
Host TOP THROUGH
BOARD
TOP VIEW OF
BOARD

Pin Num. Name Function Plug Seq. Notes

1 VeeT Transmitter Ground 1 Note 5

Transmitter Fault
2 TX Fault Indication 3 Note 1

Note 2, Module disables

3 TX Disable Transmitter Disable 3 on high or open
2-wire Serial Interface
4 SDA Module Definition 2 3 Data Line.

7
 Optical Communication System

Datasheet

5 SCL Module Definition 1 3 2-wire Serial Interface

Clock.

6 MOD-ABS Module Definition 0 3 Note 3

Rate Select 0, optionally
RX Rate Select controls SFP+ module
receiver. This pin is
7 RS0 3
(LVTTL). pulled low to VeeT with
a >30K resistor.

8 LOS Loss of Signal 3 Note 4

Rate Select 1, optionally
TX Rate Select controls SFP+ module
transmitter. This pin is
9 RS1 1
(LVTTL). pulled low to VeeT with
a >30K resistor.
10 VeeR Receiver Ground 1 Note 5
11 VeeR Receiver Ground 1 Note 5

12 RD- Inv. Received Data Out 3 Note 6

13 RD+ Received Data Out 3 Note 6

14 VeeR Receiver Ground 1 Note 5
15 VccR Receiver Power 2 3.3V ± 5%, Note 7

16 VccT Transmitter Power 2 3.3V ± 5%, Note 7

17 VeeT Transmitter Ground 1 Note 5

18 TD+ Transmit Data In 3 Note 8

19 TD- Inv. Transmit Data In 3 Note 8

20 VeeT Transmitter Ground 1 Note 5

Notes:
1. TX Fault is an open collector/drain output, which should be pulled up with a 4.7K
–10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V.
When high, output indicates a laser fault of some kind. Low indicates normal
operation. In the low state, the output will be pulled to < 0.8V.

8
 Optical Communication System

Datasheet
Datasheet

2. TX disable is an input that is used to shut down the transmitter optical output. It is
pulled up within the module with a 4.7K~10 KΩ resistor. Its states are:
Low (0 – 0.8V): Transmitter on
(>0.8, < 2.0V): Undefined
High (2.0 – 3.465V): Transmitter Disabled
Open: Transmitter Disabled

3. Module Absent, connected to VeeT or VeeR in the module.

4. LOS (Loss of Signal) is an open collector/drain output, which should be pulled up

with a 4.7K –10 KΩ resistor on host board. Pull up voltage between 2.0V and
VccT/R+0.3V. When high, this output indicates the received optical power is below
the worst-case receiver sensitivity (as defined by the standard in use). Low indicates
normal operation. In the low state, the output will be pulled to < 0.8V.

5. VeeR and VeeT may be internally connected within the SFP+ module.

6. RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω
differential lines which should be terminated with 100Ω (differential) at the user
SERDES. The AC coupling is done inside the module and is thus not required on the
host board. The voltage swing on these lines will be between 370 and 700 mV
differential (185 –350mV single ended) when properly terminated.

7. VccR and VccT are the receiver and transmitter power supplies. They are defined as
3.3V ±5% at the SFP+ connector pin. Maximum supply current is 350mA.
Recommended host board power supply filtering is shown below. Inductors with DC
resistance of less than 1 ohm should be used in order to maintain the required
voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended
supply filtering network is used, hot plugging of the SFP+ transceiver module will result
in an inrush current of no more than 30mA greater than the steady state value. VccR
and VccT may be internally connected within the SFP+ transceiver module.

8. TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential
lines with 100Ω differential termination inside the module. The AC coupling is done
inside the module and is thus not required on the host board. The inputs will accept
differential swings of 150 – 1200 mV (75 – 600mV single-ended), though it is
recommended that values between 150 and 1200 mV differential (75 – 600mV
single-ended) be used for best EMI performance.

9
 Optical Communication System

Datasheet

VI. Mechanical Specifications

10
 Copyright
Copyright
© 2009-2015
© 2009-2015
Fiberstore
Fiberstore

Optical Communication System

Datasheet
Datasheet
Test Center

Only when quality and 100% compatibility is verified and proved do our modules enter
the market. This depends on FS.COM's test center which is supported by a variety of
mainstream original brand switches and professional staff. We are proud of this test
center and believe all of these devices worth the investments, because it brings the best
to our customers.

The original switches could be found nowhere but at FS.COM's test center, eg: Juniper
MX960 & EX 4300 series, Cisco Nexus 9396PX & Cisco ASR 9000 Series, HP 5900 Series & HP
5406R ZL2 V3(J9996A), Arista 7050S-64, Brocade ICX7750-26Q & ICX6610-48, Avaya VSP
7000 MDA 2, etc.

Cisco ASR 9000 Series(A9K-MPA-1X40GE) ARISTA 7050S-64(DCS-7050S-64) Juniper MX960

Brocade ICX 7750-26Q Extreme Networks X670V VIM-40G4X Mellanox M3601Q

+86 (755) 8300 3611 [email protected] www.

Dell N4032F HP 5406R ZL2 V3(J9996A) AVAYA 7024XLS(7002QQ-MDA)

11
 Optical Communication System

Datasheet

Test Assured Program

FS.COM truly understands the value of compatibility and interoperability to each optics.
Every module FS.COM provides must run through programming and an extensive series
of platform diagnostic tests to prove its performance and compatibility. In our test center,
we care of every detail from staff to facilities—professionally trained staff, advanced test
facilities and comprehensive original-brand switches, to ensure our customers to receive
the optics with superior quality.

Our smart data system allows effective Our in-house coding facility programs all
product management and quality of our parts to standard OEM specs for
control according to the unique serial compatibility on all major vendors and
number, properly tracing the order, systems such as Cisco, Juniper, Brocade,
shipment and every part. HP, Dell, Arista and so on.

With a comprehensive line of original- The last test assured step to ensure our
brand switches, we can recreate an products to be shipped with perfect
environment and test each optics in package.
practical application to ensure quality
and distance.

12
 Copyright
Copyright
© 2009-2015
© 2009-2015
Fiberstore
Fiberstore

Optical Communication System

Datasheet

Order Information

Part Number Description

CWDM-SFP10G-20SP SFP+, 10GBase-LR, CWDM 1270nm-1330nm, SMF, 20km, LC, DOM

CWDM-SFP10G-20L SFP+, 10GBase-LR, CWDM 1350nm-1610nm, SMF, 20km, LC, DOM

CWDM-SFP10G-40S SFP+, 10GBase-ER, CWDM 1270nm-1450nm, SMF, 40km, LC, DOM

CWDM-SFP10G-40L SFP+, 10GBase-ER, CWDM 1470nm-1610nm, SMF, 40km, LC, DOM

CWDM-SFP10G-80L SFP+, 10GBase-ZR, CWDM 1470nm-1610nm, SMF, 80km, LC, DOM

Note:
Every transceiver is individually tested on corresponding equipment, walks through
the testing challenges and 100% compatible with Cisco, Arista, Juniper, Dell, Brocade
and other brands.

Page 5 of 6
13
[email protected] FS.COM
 Copyright
Copyright
© 2009-2015
© 2009-2015
Fiberstore
Fiberstore

Optical Communication System

Datasheet

Contact Us

North America (United States) Europe (Germany)

820 SW 34th Street Bldg W7 Suite H Building 7, NOVA Neufahrn Gewerbepark,

Renton, WA 98057 Am Gfild 7, 85375, Neufahrn bei Freising,
Munich
Tel: +1 (877) 205 5306
Tel: +49 (0) 89 414176412

Europe (United Kingdom) Asia (China)

F3 Building 6/F, Optics Valley Software

Third Floor 207 Regent Street
Park, Donghu Hi-Tech Development Zone,
London, W1B 3HH
Wuhan, Hubei, China
Tel: +44 (20) 3868 2768
Tel: +86 (027) 87639823

Addresses, phone number and fax number also have been listed at www.fs.com.
Please e-mail us at [email protected] or call us for assistance.

All statements, technical information, and recommendations related to the products

here are based upon information believed to be reliable or accurate. However, the
accuracy or completeness thereof is not guaranteed, and no responsibility is assumed
for any inaccuracies. Please contact FS for more information.

Fiber Optic Transceivers Copyright © 2009-2017 FS.COM All Rights Reserved.