0% found this document useful (0 votes)

22 views144 pages

Eastgrove Summary 07.16.25

The document outlines the structural analysis and design criteria for a proposed three-storey commercial building with a roof deck in Bacolod City, Negros Occidental, owned by Allenco Iloilo Realty Corp. It includes specifications regarding design codes, material strengths, load calculations, and wind load parameters based on various structural codes. The analysis incorporates factors such as earthquake and wind loads, ensuring compliance with national and international standards.

Uploaded by

Royce John Bañas

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

22 views144 pages

Eastgrove Summary 07.16.25

Uploaded by

Royce John Bañas

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 144

STRUCTURAL ANALYSIS

AND

DESIGN FOR THE PROPOSED

THREE(3)-STOREY

COMMERCIAL BUILDING WITH

ROOFDECK
PROJECT: THREE (3)- STOREY COMMERCIAL BUILDING WITH ROOFDECK
OWNER: ALLENCO ILOILO REALTY CORP.
LOCATION: BACOLOD CITY, NEGROS OCCIDENTAL

DESIGN CRITERIA

CODES:

1. NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 7TH EDITION (NSCP C101-15) 2ND
PRINTING 2019
2. UNIFORM BUILDING CODE (UBC1997)
3. AMERICAN CONCRETE INSTITUTE (ACI 318M-2014)
4. AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE 7-2016)
5. AMERICAN INSTITUTE OF STEEL CONSTRUCTION (AISC 360-16)

COMPRESSIVE STRENGTH OF CONCRETE FOR ALL STRUCTURAL MEMBERS : 21 MPa

YIELD STRENGTH OF REINFORCING STEEL FOR ALL R. C. MEMBERS : 227.6 (16mm and below) &
275.8 MPa (20mm and above)
STRUCTURAL STEEL : A36 ROLLED SHAPES (36,000psi)
SOIL BEARING CAPACITY : Borehole 1 @2.5m = 80 kN/m2, Borehole 3 @4.5m = 427 kN/m2

_________________________________
Civil Engineer
PRC NO._____________
PTR NO._____________
ISSUED AT___________
ISSUED ON___________
PROPERTY REDUCTION FACTORS: FROM TABLE 406.6.3.1.1(a), NSCP C101-15 2ND PRINTING

FOR CONCRETE COLUMNS = 0.70 x GROSS MOMENT OF INERTIA

FOR CONCRETE BEAMS = 0.35 x GROSS MOMENT OF INERTIA

DEAD LOADS

SELF-WEIGHT

ROOF DLS
CEILING + MECH, ELECTL, PLUMBING = 0.25 KN/SQM
ROOFING SHEET = 0.05 KN/SQM
PURLINS = 0.2 KN/SQM
TOTAL ROOF DL = 0.5 KN/SQM
2ND TO 3RD FLOOR DLS
WT OF RC SLAB (0.125M THK) = 3.5 KN/SQM
CHB WALL = 14.85 KN/M ON AFFECTED BEAMS (GROUND FLOOR)

LIVE LOADS

COMMERCIAL LIVE LOAD = 4.8 KN/SQM

ROOF LIVE LOAD = 0.6 KN/SQM

EARTHQUAKE LOAD PARAMETERS

ZONE 4
IMPORTANCE FACTOR 1
RWX 8.0
RWY 8.0
SOIL TYPE SD
CT 0.0853
NEAR SOURCE FACTOR 1
NV 1

WIND LOAD PARAMETERS

CODE: ASCE 7-2016

CATEGORY IV
BASIC WIND SPEED = 250 KPH
EXPOSURE B
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

WIND LOADS BASED ON IBC2012(ASCE7-10) (Directional Procedure) [UNIT: kN, m]

__________________________________________________________________________

Design Wind Loads : F = p * Area

Design Wind Pressure : p = qz*G*Cp1 - qh*G*Cp2
Velocity Pressure at Design Height z [psf] : qz = 0.00256*Kz*Kzt*Kd*V^2
Velocity Pressure at Mean Roof Height [psf] : qh = 0.00256*Kh*Kht*Kd*V^2
Calculated Value of qh for X-dir [psf] : qh = 64.76
Calculated Value of qh for Y-dir [psf] : qh = 64.76

Basic Wind Speed [mph] : V = 155.00

Directional Factor for X-dir Wind Loads : Kdx = 0.85
Directional Factor for Y-dir Wind Loads : Kdy = 0.85
Exposure Category : D
Mean Roof Height : H = 43.31
Gradient Height [ft] : Zg = 700.00
Power Law Exponent : Alpha= 11.50
Kz at Mean Roof Height (Kh) : Kh = 1.24

Structural Rigidity : Rigid Structure

Gust effect Factor for X-dir Wind Loads : Gx = 0.85

Gust effect Factor for Y-dir Wind Loads : Gy = 0.85

Topographic Effects for X-dir Wind Loads : Not Included

Topographic Effects for Y-dir Wind Loads : Not Included
Accidental Eccentricity for X-direction : Wx = None
Accidental Eccentricity for Y-direction : Wy = None
Scale Factor for X-directional Wind Loads : SFx = 1.00
Scale Factor for Y-directional Wind Loads : SFy = 0.00

-----------------------------------------------------------------------------------------------

Wind force of the specific story is calculated as the sum of the forces
of the following two parts.
1. Part I : Lower half part of the specific story
2. Part II : Upper half part of the just below story of the specific story

The reference height for the calculation of the wind pressure related factors are,
therefore, considered separately for the above mentioned two parts as follows.

Reference height for the wind pressure related factors(except topographic related factors)
1. Part I : top level of the specific story
2. Part II : top level of the just below story of the specific story

Reference height for the topographic related factors :

1. Part I : bottom level of the specific story
2. Part II : bottom level of the just below story of the specific story

-----------------------------------------------------------------------------------------------

** External Pressure Coefficients at Windward and Leeward Walls (Cp1, Cp2)

STORY Cp1 Cp2(X-DIR) Cp2(Y-DIR)

NAME (Windward) (Leeward) (Leeward)
---------- ----------- ----------- -----------
Roof 0.800 -0.500 -0.298
4F 0.800 -0.500 -0.298
3F 0.800 -0.500 -0.298
2F 0.800 -0.500 -0.298
1F 0.800 -0.500 -0.298
B 0.000 0.000 0.000
----------------------------------------------

** Velocity Exposure Coefficients at Design Height (Kz)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -1/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

** Topographic Factors at Windward and Leeward Walls (Kzt)

** Velocity Pressure at Design Height (qz) [Current Unit]
STORY Kz Kzt(X-DIR) Kzt(Y-DIR) Kzt(X-DIR) Kzt(Y-DIR) qz(X-DIR) qz(Y-DI
R)
NAME (Windward) (Windward) (Leeward) (Leeward)
---------- ----------- ----------- ----------- ----------- ----------- ----------- ---------
--
Roof 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
4F 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
3F 1.258 1.000 1.000 1.000 1.000 3.148 3.1
48
2F 1.185 1.000 1.000 1.000 1.000 2.965 2.9
65
1F 1.080 1.000 1.000 1.000 1.000 2.703 2.7
03
B 0.000 0.000 0.000 0.000 0.000 0.000 0.0
00
--------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 3.488533 15.6 0.6 81.8 171.2172 0.0 171.2172 0.0 0
.0
4F 3.488533 14.4 2.7 81.8 765.32265 0.0 765.32265 171.2172 205.460
64
3F 3.458525 10.2 4.2 81.8 1166.8057 0.0 1166.8057 936.53985 4138.9
28
2F 3.333917 6.0 5.1 81.8 1347.2301 0.0 1347.2301 2103.3456 12972.9
79
G.L. 3.156193 0.0 3.0 81.8 774.52985 0.0 -- 3450.5757 33676.4
34
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 2.956415 15.6 0.6 40.141 71.204064 0.0 0.0 0.0 0
.0
4F 2.956415 14.4 2.7 40.141 317.88875 0.0 0.0 0.0 0
.0
3F 2.926407 10.2 4.2 40.141 482.8654 0.0 0.0 0.0 0
.0
2F 2.801799 6.0 5.1 40.141 552.17971 0.0 0.0 0.0 0
.0
G.L. 2.624075 0.0 3.0 40.141 315.99899 0.0 -- 0.0 0
.0
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A RZ - D I R E C T I O N

STORY NAME TORSIONAL ELEV. LOADED LOADED WIND ADDED STORY ACCUMULATED
PRESSURE HEIGHT BREADTH TORSION TORSION TORSION TORSION

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -2/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

---------- --------- ------- ------- ------- ---------- ---------- ---------- -----------

Roof 0.0 15.6 0.6 81.8 0.0 0.0 0.0 0.0
4F 0.0 14.4 2.7 81.8 0.0 0.0 0.0 0.0
3F 0.0 10.2 4.2 81.8 0.0 0.0 0.0 0.0
2F 0.0 6.0 5.1 81.8 0.0 0.0 0.0 0.0
G.L. 0.0 0.0 3.0 81.8 0.0 0.0 -- 0.0
-----------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

STORY STORY STORY ACCIDENTAL ACCIDENTAL ACCIDENTAL ACCIDENTAL

NAME FORCE(X) FORCE(Y) ECCENT.(X) ECCENT.(Y) TORSION(X) TORSION(Y)
---------- ---------- ---------- ---------- ---------- ---------- ----------
Roof 171.2172 0.0 0.0 0.0 0.0 0.0
4F 765.32265 0.0 0.0 0.0 0.0 0.0
3F 1166.8057 0.0 0.0 0.0 0.0 0.0
2F 1347.2301 0.0 0.0 0.0 0.0 0.0
G.L. -- -- 0.0 0.0 -- --

WIND LOADS BASED ON IBC2012(ASCE7-10) (Directional Procedure) [UNIT: kN, m]

__________________________________________________________________________

Design Wind Loads : F = p * Area

Basic Wind Speed [mph] : V = 155.00

Structural Rigidity : Rigid Structure

Gust effect Factor for X-dir Wind Loads : Gx = 0.85

Gust effect Factor for Y-dir Wind Loads : Gy = 0.85

Topographic Effects for X-dir Wind Loads : Not Included

Topographic Effects for Y-dir Wind Loads : Not Included
Accidental Eccentricity for X-direction : Wx = None
Accidental Eccentricity for Y-direction : Wy = None
Scale Factor for X-directional Wind Loads : SFx = 0.00
Scale Factor for Y-directional Wind Loads : SFy = 1.00

-----------------------------------------------------------------------------------------------

The reference height for the calculation of the wind pressure related factors are,
therefore, considered separately for the above mentioned two parts as follows.

Reference height for the topographic related factors :

1. Part I : bottom level of the specific story
2. Part II : bottom level of the just below story of the specific story

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -3/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

-----------------------------------------------------------------------------------------------

** External Pressure Coefficients at Windward and Leeward Walls (Cp1, Cp2)

STORY Cp1 Cp2(X-DIR) Cp2(Y-DIR)

** Velocity Exposure Coefficients at Design Height (Kz)

** Topographic Factors at Windward and Leeward Walls (Kzt)
** Velocity Pressure at Design Height (qz) [Current Unit]
STORY Kz Kzt(X-DIR) Kzt(Y-DIR) Kzt(X-DIR) Kzt(Y-DIR) qz(X-DIR) qz(Y-DI
R)
NAME (Windward) (Windward) (Leeward) (Leeward)
---------- ----------- ----------- ----------- ----------- ----------- ----------- ---------
--
Roof 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
4F 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
3F 1.258 1.000 1.000 1.000 1.000 3.148 3.1
48
2F 1.185 1.000 1.000 1.000 1.000 2.965 2.9
65
1F 1.080 1.000 1.000 1.000 1.000 2.703 2.7
03
B 0.000 0.000 0.000 0.000 0.000 0.000 0.0
00
--------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 3.488533 15.6 0.6 81.8 171.2172 0.0 0.0 0.0 0
.0
4F 3.488533 14.4 2.7 81.8 765.32265 0.0 0.0 0.0 0
.0
3F 3.458525 10.2 4.2 81.8 1166.8057 0.0 0.0 0.0 0
.0
2F 3.333917 6.0 5.1 81.8 1347.2301 0.0 0.0 0.0 0
.0
G.L. 3.156193 0.0 3.0 81.8 774.52985 0.0 -- 0.0 0
.0
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -4/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 2.956415 15.6 0.6 40.141 71.204064 0.0 71.204064 0.0 0
.0
4F 2.956415 14.4 2.7 40.141 317.88875 0.0 317.88875 71.204064 85.4448
77
3F 2.926407 10.2 4.2 40.141 482.8654 0.0 482.8654 389.09282 1719.63
47
2F 2.801799 6.0 5.1 40.141 552.17971 0.0 552.17971 871.95822 5381.85
92
G.L. 2.624075 0.0 3.0 40.141 315.99899 0.0 -- 1424.1379 13926.6
87
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A RZ - D I R E C T I O N

STORY NAME TORSIONAL ELEV. LOADED LOADED WIND ADDED STORY ACCUMULATED
PRESSURE HEIGHT BREADTH TORSION TORSION TORSION TORSION
---------- --------- ------- ------- ------- ---------- ---------- ---------- -----------
Roof 0.0 15.6 0.6 81.8 0.0 0.0 0.0 0.0
4F 0.0 14.4 2.7 81.8 0.0 0.0 0.0 0.0
3F 0.0 10.2 4.2 81.8 0.0 0.0 0.0 0.0
2F 0.0 6.0 5.1 81.8 0.0 0.0 0.0 0.0
G.L. 0.0 0.0 3.0 81.8 0.0 0.0 -- 0.0
-----------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

STORY STORY STORY ACCIDENTAL ACCIDENTAL ACCIDENTAL ACCIDENTAL

NAME FORCE(X) FORCE(Y) ECCENT.(X) ECCENT.(Y) TORSION(X) TORSION(Y)
---------- ---------- ---------- ---------- ---------- ---------- ----------
Roof 0.0 71.204064 0.0 0.0 0.0 0.0
4F 0.0 317.88875 0.0 0.0 0.0 0.0
3F 0.0 482.8654 0.0 0.0 0.0 0.0
2F 0.0 552.17971 0.0 0.0 0.0 0.0
G.L. -- -- 0.0 0.0 -- --

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -5/5-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]

_________________________________________________________

STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS

NAME (X-DIR) (Y-DIR) MASS (X-COORD) (Y-COORD)
----------- ----------- ----------- ----------- ----------- -----------
Roof 0.64863996 0.64863996 772.298843 13.52275 44.85
4F 176.583759 176.583759 115982.466 16.4422173 51.6497847
3F 842.993764 842.993764 520837.547 16.9053798 52.6418911
2F 853.404107 853.404107 527674.699 16.9388312 52.5244546
1F 707.624505 707.624505 354342.959 18.3844407 58.4461305
B 1477.79101 1477.79101 442551.395 20.8647649 63.8142216
----------- ----------- ----------- ----------- ----------- -----------
TOTAL : 4059.04579 4059.04579

* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE

_____________________________________________________________________

Note. The following masses are between two adjacent stories or on the
nodes released from floor rigid diaphragm by *Diaphragm Disconnect command.
The masses are proportionally distributed to upper/lower stories according
to their vertical locations. For dynamic analysis, however, floor masses
and masses on vertical elements remain at their original locations.

STORY TRANSLATIONAL MASS

NAME (X-DIR) (Y-DIR)
-------------- ----------- -----------
Roof 0.0 0.0
4F 0.0 0.0
3F 0.0 0.0
2F 0.0 0.0
1F 104.07731 104.07731
B 142.868276 142.868276
-------------- ----------- -----------
TOTAL : 246.945586 246.945586

* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________

Seismic Zone Factor (Z) : 0.40

Importance Factor (I) : 1.00
Soil Profile Type : SD

Seismic Source Type : B

Closest Distance To Known Seismic Source [km] : 10.00
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00

Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44

Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64

Fundamental Period Associated With X-dir. (Tx) : 0.1980

R Factor of Lateral System for X-direction (Rx) : 8.0000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.137500

Fundamental Period Associated With Y-dir. (Ty) : 0.1980

R Factor of Lateral System for Y-direction (Ry) : 8.0000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.137500

Total Effective Weight For X-dir. Seismic Loads (Wx) : 26332.366434

Total Effective Weight For Y-dir. Seismic Loads (Wy) : 26332.366434

Scale Factor For X-directional Seismic Loads : 1.00

Scale Factor For Y-directional Seismic Loads : 0.00

Accidental Eccentricity For X-direction (Ex) : Positive

Accidental Eccentricity For Y-direction (Ey) : Positive

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -1/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

Torsional Amplification for Accidental Eccentricity : Do not Consider

Torsional Amplification for Inherent Eccentricity : Do not Consider

Total Base Shear Of Model For X-direction : 3620.700385

Total Base Shear Of Model For Y-direction : 0.000000
Summation Of Wi*Hi Of Model For X-direction : 251725.396218
Summation Of Wi*Hi Of Model For Y-direction : 0.000000
--------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D

STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INH

ERENT
NAME ECCENT. ECCENT. AMP.FACTOR AMP.FACTOR ECCENT. ECCENT. AMP.FACTOR AMP
.FACTOR
---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---
-------
Roof -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
4F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
3F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
2F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
1F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
G.L 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0
------------------------------------------------------------------------------------------------
-------

------------------------------------------------------------------------------------------------
-------
The accidental amplification factors are automatically set to 1.0 when torsional amplification e
ffect
to accidental eccentricity is not considered.
The inherent amplification factors are automatically set to 0 when torsional amplification effec
t
to inherent eccentricity is not considered.
The inherent amplification factors are all set to 'the input value - 1.0'.(This is to exclude th
e true
inherent torsion)
------------------------------------------------------------------------------------------------
-------

** Story Force , Seismic Force x Scale Factor + Added Force

S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -2/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

3F 8266.397 13.7 1628.93 0.0 1628.93 447.5691 1881.887 6662.323 0.0 6

662.323
2F 8368.481 9.5 1143.499 0.0 1143.499 2076.499 10603.18 4676.911 0.0 4
676.911
1F 7959.548 3.5 400.7025 0.0 400.7025 3219.998 29923.17 1638.873 0.0 1
638.873
G.L. -- 0.0 -- -- -- 3620.7 42595.62 --- ---
---
------------------------------------------------------------------------------------------------
-------

S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT T
OTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION T
ORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- --
-------
Roof 6.360563 19.1 1.747409 0.0 0.0 0.0 0.0 0.0 0.0
0.0
4F 1731.58 17.9 445.8217 0.0 0.0 0.0 0.0 0.0 0.0
0.0
3F 8266.397 13.7 1628.93 0.0 0.0 0.0 0.0 0.0 0.0
0.0
2F 8368.481 9.5 1143.499 0.0 0.0 0.0 0.0 0.0 0.0
0.0
1F 7959.548 3.5 400.7025 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
------------------------------------------------------------------------------------------------
-------

=================================================
COMMENTS ABOUT TORSION
=================================================

------------------------------------------------------------------------------------------------
-------
If torsional amplification effects are considered :
------------------------------------------------------------------------------------------------
-------
Accidental Torsion , Story Force * Accidental Eccentricity * Amp. Factor for Accidental Eccentri
city
Inherent Torsion , Story Force * Inherent Eccentricity * Amp. Factor for Inherent Eccentricity

------------------------------------------------------------------------------------------------
-------
If torsional amplification effects are not considered :
------------------------------------------------------------------------------------------------
-------
Accidental Torsion , Story Force * Accidental Eccentricity
Inherent Torsion , 0

------------------------------------------------------------------------------------------------
-------
The inherent torsion above is the additional torsion due to torsional amplification effect.
The true inherent torsion is considered automatically in analysis stage when the seismic force i
s
applied to the structure.
------------------------------------------------------------------------------------------------
-------

* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]

_________________________________________________________

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -3/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS

* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE

_____________________________________________________________________

STORY TRANSLATIONAL MASS

* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________

Seismic Zone Factor (Z) : 0.40

Importance Factor (I) : 1.00
Soil Profile Type : SD

Seismic Source Type : B

Closest Distance To Known Seismic Source [km] : 10.00
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00

Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44

Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64

Fundamental Period Associated With X-dir. (Tx) : 0.1980

R Factor of Lateral System for X-direction (Rx) : 8.0000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.137500

Fundamental Period Associated With Y-dir. (Ty) : 0.1980

R Factor of Lateral System for Y-direction (Ry) : 8.0000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.137500

Total Effective Weight For X-dir. Seismic Loads (Wx) : 26332.366434

Total Effective Weight For Y-dir. Seismic Loads (Wy) : 26332.366434

Scale Factor For X-directional Seismic Loads : 0.00

Scale Factor For Y-directional Seismic Loads : 1.00

Accidental Eccentricity For X-direction (Ex) : Positive

Accidental Eccentricity For Y-direction (Ey) : Positive

Torsional Amplification for Accidental Eccentricity : Do not Consider

Torsional Amplification for Inherent Eccentricity : Do not Consider

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -4/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

Total Base Shear Of Model For X-direction : 0.000000

Total Base Shear Of Model For Y-direction : 3620.700385
Summation Of Wi*Hi Of Model For X-direction : 0.000000
Summation Of Wi*Hi Of Model For Y-direction : 251725.396218
--------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D

STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INH

** Story Force , Seismic Force x Scale Factor + Added Force

S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -5/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

0.0
1F 7959.548 3.5 400.7025 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
------------------------------------------------------------------------------------------------
-------

S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT T
OTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION T
ORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- --
-------
Roof 6.360563 19.1 1.747409 0.0 1.747409 0.0 0.0 3.507137 0.0 3
.507137
4F 1731.58 17.9 445.8217 0.0 445.8217 1.747409 2.096891 894.7865 0.0 8
94.7865
3F 8266.397 13.7 1628.93 0.0 1628.93 447.5691 1881.887 3269.344 0.0 3
269.344
2F 8368.481 9.5 1143.499 0.0 1143.499 2076.499 10603.18 2295.06 0.0
2295.06
1F 7959.548 3.5 400.7025 0.0 400.7025 3219.998 29923.17 804.2299 0.0 8
04.2299
G.L. -- 0.0 -- -- -- 3620.7 42595.62 --- ---
---
------------------------------------------------------------------------------------------------
-------

=================================================
COMMENTS ABOUT TORSION
=================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -6/6-
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...\Eastgrove China.mgb
z
1. Design Information

0.0158
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 451

0.36
y
Material A36 (No:1)

0.180
0.014
(Fy = 248211, Es = 199948024)
Section Name I 36c (No:33) 0.070

(Rolled : I 36c).
0.14
Member Length : 6.00000

2. Member Forces Depth 0.36000 Web Thick 0.01400

Axial Force Fxx = 0.00000 (LCB: 2, POS:1/2) Top F Width 0.14000 Top F Thick 0.01580
Bot.F Width 0.14000 Bot.F Thick 0.01580
Bending Moments My = 76.7007, Mz = 0.00000
Area 0.00908 Asz 0.00504
End Moments Myi = -69.571, Myj = -0.1400 (for Lb) Qyb 0.04067 Qzb 0.00245
Iyy 0.00017 Izz 0.00001
Myi = -69.571, Myj = -0.1400 (for Ly) Ybar 0.07000 Zbar 0.18000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00096 Szz 0.00009
ry 0.13820 rz 0.02600
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -71.980 (LCB: 2, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 6.00000, Lz = 6.00000, Lb = 6.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 230.8 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/2029.28 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 76.701/130.567 = 0.587 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/31.3461 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.587 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.096 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:08
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...\Eastgrove China.mgb
z
1. Design Information

0.0165
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 163 y

0.4
Material A36 (No:1)

0.2000
0.0145
(Fy = 248211, Es = 199948024)
Section Name I 40c (No:37) 0.0730

(Rolled : I 40c).
0.146
Member Length : 2.98333

2. Member Forces Depth 0.40000 Web Thick 0.01450

Axial Force Fxx = 0.00000 (LCB: 8, POS:1/4) Top F Width 0.14600 Top F Thick 0.01650
Bot.F Width 0.14600 Bot.F Thick 0.01650
Bending Moments My = 53.1480, Mz = 0.00000
Area 0.01021 Asz 0.00580
End Moments Myi = 50.7948, Myj = 16.8957 (for Lb) Qyb 0.04869 Qzb 0.00266
Iyy 0.00024 Izz 0.00001
Myi = 50.7948, Myj = 16.8957 (for Ly) Ybar 0.07300 Zbar 0.20000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00119 Szz 0.00010
ry 0.15290 rz 0.02670
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = 32.5421 (LCB: 2, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 2.98333, Lz = 2.98333, Lb = 2.98333
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 111.7 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/2280.14 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 53.148/261.301 = 0.203 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/35.6352 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.203 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.038 < 1.000 ...................................................... O.K

0.018
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 45

0.45
y
Material A36 (No:1)

0.2250
0.0135
(Fy = 248211, Es = 199948024)
Section Name I 45b (No:31) 0.0760

(Rolled : I 45b).
0.152
Member Length : 6.00000

2. Member Forces Depth 0.45000 Web Thick 0.01350

Axial Force Fxx = 0.00000 (LCB: 8, POS:I) Top F Width 0.15200 Top F Thick 0.01800
Bot.F Width 0.15200 Bot.F Thick 0.01800
Bending Moments My = -179.53, Mz = 0.00000
Area 0.01114 Asz 0.00608
End Moments Myi = -179.53, Myj = 101.550 (for Lb) Qyb 0.06520 Qzb 0.00289
Iyy 0.00034 Izz 0.00001
Myi = -179.53, Myj = 101.550 (for Ly) Ybar 0.07600 Zbar 0.22500
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00150 Szz 0.00012
ry 0.17410 rz 0.02840
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -73.697 (LCB: 8, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 6.00000, Lz = 6.00000, Lb = 6.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 211.3 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/2488.57 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 179.525/195.008 = 0.921 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/42.1046 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.921 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.081 < 1.000 ...................................................... O.K

0.018
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.488
Member No 743 y
Material A36 (No:1)

0.244
0.011
(Fy = 248211, Es = 199948024)
Section Name HM 488x300x11/18 (No:32) 0.150

(Rolled : HM 488x300x11/18).
0.3
Member Length : 11.4580

2. Member Forces Depth 0.48800 Web Thick 0.01100

Axial Force Fxx = 0.00000 (LCB: 13, POS:J) Top F Width 0.30000 Top F Thick 0.01800
Bot.F Width 0.30000 Bot.F Thick 0.01800
Bending Moments My = -38.961, Mz = 0.00000
Area 0.01592 Asz 0.00537
End Moments Myi = -38.299, Myj = -38.961 (for Lb) Qyb 0.14090 Qzb 0.01125
Iyy 0.00068 Izz 0.00008
Myi = -38.299, Myj = -38.961 (for Ly) Ybar 0.15000 Zbar 0.24400
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00278 Szz 0.00054
ry 0.20660 rz 0.07140
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = 12.4138 (LCB: 11, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 11.4580, Lz = 11.4580, Lb = 11.4580
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 160.5 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/3556.15 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 38.961/413.335 = 0.094 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/184.000 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.094 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.016 < 1.000 ...................................................... O.K

0.02
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.588
Member No 69 y
Material A36 (No:1)

0.294
0.012
(Fy = 248211, Es = 199948024)
Section Name HM 588x300x12/20 (No:36) 0.150

(Rolled : HM 588x300x12/20).
0.3
Member Length : 1.00000

2. Member Forces Depth 0.58800 Web Thick 0.01200

Axial Force Fxx = 0.00000 (LCB: 8, POS:I) Top F Width 0.30000 Top F Thick 0.02000
Bot.F Width 0.30000 Bot.F Thick 0.02000
Bending Moments My = -35.891, Mz = 0.00000
Area 0.01872 Asz 0.00706
End Moments Myi = -35.891, Myj = 0.02203 (for Lb) Qyb 0.17954 Qzb 0.01125
Iyy 0.00113 Izz 0.00009
Myi = -35.891, Myj = 0.02203 (for Ly) Ybar 0.15000 Zbar 0.29400
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00384 Szz 0.00060
ry 0.24550 rz 0.06940
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -38.979 (LCB: 8, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 1.00000, Lz = 1.00000, Lb = 1.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 14.4 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/4182.09 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 35.891/962.569 = 0.037 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/205.458 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.037 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.037 < 1.000 ...................................................... O.K

0.023
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.594
Member No 353 y
Material A36 (No:1)

0.297
0.014
(Fy = 248211, Es = 199948024)
Section Name HM 594x302x14/23 (No:38) 0.151

(Rolled : HM 594x302x14/23).
0.302
Member Length : 4.20000

2. Member Forces Depth 0.59400 Web Thick 0.01400

Axial Force Fxx = -428.31 (LCB: 8, POS:J) Top F Width 0.30200 Top F Thick 0.02300
Bot.F Width 0.30200 Bot.F Thick 0.02300
Bending Moments My = -208.27, Mz = 127.861
Area 0.02171 Asz 0.00832
End Moments Myi = 216.184, Myj = -208.27 (for Lb) Qyb 0.17919 Qzb 0.01140
Iyy 0.00132 Izz 0.00011
Myi = 216.184, Myj = -208.27 (for Ly) Ybar 0.15100 Zbar 0.29700
Mzi = -121.97, Mzj = 127.861 (for Lz) Syy 0.00445 Szz 0.00070
ry 0.24680 rz 0.06980
Shear Forces Fyy = -59.483 (LCB: 8, POS:1/2)
Fzz = 148.734 (LCB: 7, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 4.20000, Lz = 4.20000, Lb = 4.20000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 60.2 < 200.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 428.31/4007.97 = 0.107 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 208.27/1081.82 = 0.193 < 1.000 ................................... O.K
Mrz/Mcz = 127.861/240.300 = 0.532 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.11 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.778 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.032 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.120 < 1.000 ...................................................... O.K

0.019
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 21

0.35
y
Material A36 (No:1)

0.175
0.012
(Fy = 248211, Es = 199948024)
Section Name HW 350x350x12/19 (No:35) 0.175

(Rolled : HW 350x350x12/19).
0.35
Member Length : 4.80000

2. Member Forces Depth 0.35000 Web Thick 0.01200

Axial Force Fxx = -309.48 (LCB: 10, POS:I) Top F Width 0.35000 Top F Thick 0.01900
Bot.F Width 0.35000 Bot.F Thick 0.01900
Bending Moments My = -51.927, Mz = 162.448
Area 0.01719 Asz 0.00420
End Moments Myi = -51.927, Myj = 68.7098 (for Lb) Qyb 0.10388 Qzb 0.01531
Iyy 0.00040 Izz 0.00014
Myi = -51.927, Myj = 68.7098 (for Ly) Ybar 0.17500 Zbar 0.17500
Mzi = 162.448, Mzj = -137.25 (for Lz) Syy 0.00227 Szz 0.00078
ry 0.15190 rz 0.08890
Shear Forces Fyy = 62.4369 (LCB: 10, POS:1/2)
Fzz = -71.387 (LCB: 5, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 4.80000, Lz = 4.80000, Lb = 4.80000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 54.0 < 200.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 309.48/3293.54 = 0.094 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 51.927/551.080 = 0.094 < 1.000 ................................... O.K
Mrz/Mcz = 162.448/262.479 = 0.619 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.09 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.760 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.035 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.114 < 1.000 ...................................................... O.K

0.0158
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 731

0.36
y
Material A36 (No:1)

0.18
0.01
(Fy = 248211, Es = 199948024)
Section Name I 36a (No:34) 0.07

(Rolled : I 36a).
0.136
Member Length : 3.00000

2. Member Forces Depth 0.36000 Web Thick 0.01000

Axial Force Fxx = 0.00000 (LCB: 5, POS:I) Top F Width 0.13600 Top F Thick 0.01580
Bot.F Width 0.13600 Bot.F Thick 0.01580
Bending Moments My = -54.002, Mz = 0.00000
Area 0.00764 Asz 0.00360
End Moments Myi = -54.002, Myj = 24.8875 (for Lb) Qyb 0.05046 Qzb 0.00231
Iyy 0.00016 Izz 0.00001
Myi = -54.002, Myj = 24.8875 (for Ly) Ybar 0.06800 Zbar 0.18000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00088 Szz 0.00008
ry 0.12380 rz 0.02690
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -34.782 (LCB: 5, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 3.00000, Lz = 3.00000, Lb = 3.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 111.5 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/1707.59 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 54.002/183.906 = 0.294 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/29.1658 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.294 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.065 < 1.000 ...................................................... O.K

0.0282
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 333 y

0.7
Material A36 (No:1)

0.3500
0.0175
(Fy = 248211, Es = 199948024)
Section Name I 70b (No:53) 0.1050

(Rolled : I 70b).
0.21
Member Length : 3.31667

2. Member Forces Depth 0.70000 Web Thick 0.01750

Axial Force Fxx = 0.00000 (LCB: 2, POS:J) Top F Width 0.21000 Top F Thick 0.02820
Bot.F Width 0.21000 Bot.F Thick 0.02820
Bending Moments My = -763.48, Mz = 0.00000
Area 0.02430 Asz 0.01225
End Moments Myi = 194.502, Myj = -763.48 (for Lb) Qyb 0.16545 Qzb 0.00551
Iyy 0.00175 Izz 0.00004
Myi = 194.502, Myj = -763.48 (for Ly) Ybar 0.10500 Zbar 0.35000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00501 Szz 0.00037
ry 0.27380 rz 0.04090
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = 325.236 (LCB: 2, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 3.31667, Lz = 3.31667, Lb = 3.31667
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 81.1 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/5428.38 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 763.48/1166.77 = 0.654 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/133.098 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.654 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.178 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/15/2025 15:19
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-07-12-25.mgb
z
1. Design Information

0.05
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.458
Member No 99 y
Material A36 (No:1)

0.23
0.03
(Fy = 248211, Es = 199948024)
Section Name HW 458x417x30/50 (No:52) 0.21

(Rolled : HW 458x417x30/50).
0.417
Member Length : 3.81933

2. Member Forces Depth 0.45800 Web Thick 0.03000

Axial Force Fxx = 0.00000 (LCB: 2, POS:I) Top F Width 0.41700 Top F Thick 0.05000
Bot.F Width 0.41700 Bot.F Thick 0.05000
Bending Moments My = -1648.4, Mz = 0.00000
Area 0.05285 Asz 0.01374
End Moments Myi = -1648.4, Myj = 635.517 (for Lb) Qyb 0.15780 Qzb 0.02174
Iyy 0.00191 Izz 0.00061
Myi = -1648.4, Myj = 635.517 (for Ly) Ybar 0.20850 Zbar 0.22900
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00834 Szz 0.00290
ry 0.19010 rz 0.10700
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -650.65 (LCB: 2, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 3.81933, Lz = 3.81933, Lb = 3.81933
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 35.7 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.0/11807.3 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 1648.41/2115.07 = 0.779 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/989.122 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.779 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.318 < 1.000 ...................................................... O.K

0.025
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.502
Member No 70 y
Material A36 (No:1)

0.251
0.015
(Fy = 248211, Es = 199948024)
Section Name HW 502x465x15/25 (No:36) 0.233

(Rolled : HW 502x465x15/25).
0.465
Member Length : 1.50000

2. Member Forces Depth 0.50200 Web Thick 0.01500

Axial Force Fxx = 0.00000 (LCB: 5, POS:I) Top F Width 0.46500 Top F Thick 0.02500
Bot.F Width 0.46500 Bot.F Thick 0.02500
Bending Moments My = -483.55, Mz = 0.00000
Area 0.03044 Asz 0.00753
End Moments Myi = -483.55, Myj = -236.83 (for Lb) Qyb 0.21038 Qzb 0.02703
Iyy 0.00145 Izz 0.00042
Myi = -483.55, Myj = -236.83 (for Ly) Ybar 0.23250 Zbar 0.25100
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00578 Szz 0.00180
ry 0.21820 rz 0.11730
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -173.14 (LCB: 5, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 1.50000, Lz = 1.50000, Lb = 1.50000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 12.8 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/6801.11 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 483.55/1409.87 = 0.343 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/609.461 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.343 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.154 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/14/2025 14:00
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-07-12-25.mgb
z
1. Design Information

0.023
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.594
Member No 345 y
Material A36 (No:1)

0.297
0.014
(Fy = 248211, Es = 199948024)
Section Name HM 594x302x14/23 (No:38) 0.151

(Rolled : HM 594x302x14/23).
0.302
Member Length : 4.20000

2. Member Forces Depth 0.59400 Web Thick 0.01400

Axial Force Fxx = -1563.4 (LCB: 14, POS:J) Top F Width 0.30200 Top F Thick 0.02300
Bot.F Width 0.30200 Bot.F Thick 0.02300
Bending Moments My = 132.090, Mz = -101.78
Area 0.02171 Asz 0.00832
End Moments Myi = -209.98, Myj = 132.090 (for Lb) Qyb 0.17919 Qzb 0.01140
Iyy 0.00132 Izz 0.00011
Myi = -209.98, Myj = 132.090 (for Ly) Ybar 0.15100 Zbar 0.29700
Mzi = -66.759, Mzj = -101.78 (for Lz) Syy 0.00445 Szz 0.00070
ry 0.24680 rz 0.06980
Shear Forces Fyy = 48.8039 (LCB: 12, POS:1/2)
Fzz = -153.69 (LCB: 13, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 4.20000, Lz = 4.20000, Lb = 4.20000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 60.2 < 200.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 1563.44/4007.97 = 0.390 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 132.09/1081.82 = 0.122 < 1.000 ................................... O.K
Mrz/Mcz = 101.782/240.300 = 0.424 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.39 > 0.20
Rmax = Pr/Pc + 8/9*[Mry/Mcy + Mrz/Mcz] = 0.875 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.026 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.124 < 1.000 ...................................................... O.K

0.024
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 134 y

0.7
Material A36 (No:1)

0.350
0.013
(Fy = 248211, Es = 199948024)
Section Name HN 700x300x13/24 (No:55) 0.150

(Rolled : HN 700x300x13/24).
0.3
Member Length : 3.81933

2. Member Forces Depth 0.70000 Web Thick 0.01300

Axial Force Fxx = 0.00000 (LCB: 3, POS:J) Top F Width 0.30000 Top F Thick 0.02400
Bot.F Width 0.30000 Bot.F Thick 0.02400
Bending Moments My = -1299.5, Mz = 0.00000
Area 0.02315 Asz 0.00910
End Moments Myi = 272.478, Myj = -1299.5 (for Lb) Qyb 0.24034 Qzb 0.01125
Iyy 0.00194 Izz 0.00011
Myi = 272.478, Myj = -1299.5 (for Ly) Ybar 0.15000 Zbar 0.35000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00553 Szz 0.00072
ry 0.28920 rz 0.06830
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = 457.517 (LCB: 2, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 3.81933, Lz = 3.81933, Lb = 3.81933
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 55.9 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/5172.38 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 1299.53/1365.26 = 0.952 < 1.000 ................................... O.K
Mrz/Mcz = 0.000/247.415 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.952 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.338 < 1.000 ...................................................... O.K

0.028
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.758
Member No 7 y
Material A36 (No:1)

0.379
0.016
(Fy = 248211, Es = 199948024)
Section Name HN 758x303x16/28 (No:51) 0.151

(Rolled : HN 758x303x16/28).
0.303
Member Length : 6.00000

2. Member Forces Depth 0.75800 Web Thick 0.01600

Axial Force Fxx = -2206.9 (LCB: 5, POS:J) Top F Width 0.30300 Top F Thick 0.02800
Bot.F Width 0.30300 Bot.F Thick 0.02800
Bending Moments My = -700.65, Mz = -9.3182
Area 0.02848 Asz 0.01213
End Moments Myi = 648.360, Myj = -700.65 (for Lb) Qyb 0.25514 Qzb 0.01148
Iyy 0.00271 Izz 0.00013
Myi = 648.360, Myj = -700.65 (for Ly) Ybar 0.15150 Zbar 0.37900
Mzi = 10.0713, Mzj = -7.4445 (for Lz) Syy 0.00716 Szz 0.00086
ry 0.30870 rz 0.06760
Shear Forces Fyy = 3.93024 (LCB: 12, POS:1/2)
Fzz = 224.835 (LCB: 5, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 6.00000, Lz = 6.00000, Lb = 6.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 88.8 < 200.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 2206.90/4202.04 = 0.525 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 700.65/1576.70 = 0.444 < 1.000 ................................... O.K
Mrz/Mcz = 9.318/297.166 = 0.031 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.53 > 0.20
Rmax = Pr/Pc + 8/9*[Mry/Mcy + Mrz/Mcz] = 0.948 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.002 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.124 < 1.000 ...................................................... O.K

0.034
Design Code AISC(15th)-LRFD16
Unit System kN, m

0.912
Member No 7 y
Material A36 (No:1)

0.456
0.018
(Fy = 248211, Es = 199948024)
Section Name HN 912x302x18/34 (No:58) 0.151

(Rolled : HN 912x302x18/34).
0.302
Member Length : 6.00000

2. Member Forces Depth 0.91200 Web Thick 0.01800

Axial Force Fxx = -2914.8 (LCB: 5, POS:J) Top F Width 0.30200 Top F Thick 0.03400
Bot.F Width 0.30200 Bot.F Thick 0.03400
Bending Moments My = -909.59, Mz = -16.971
Area 0.03601 Asz 0.01642
End Moments Myi = 859.139, Myj = -909.59 (for Lb) Qyb 0.33947 Qzb 0.01140
Iyy 0.00485 Izz 0.00016
Myi = 859.139, Myj = -909.59 (for Ly) Ybar 0.15100 Zbar 0.45600
Mzi = 16.8182, Mzj = -12.982 (for Lz) Syy 0.01063 Szz 0.00104
ry 0.36690 rz 0.06590
Shear Forces Fyy = 6.75201 (LCB: 2, POS:1/2)
Fzz = 294.789 (LCB: 5, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 6.00000, Lz = 6.00000, Lb = 6.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 91.0 < 200.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 2914.78/5198.92 = 0.561 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 909.59/2339.38 = 0.389 < 1.000 ................................... O.K
Mrz/Mcz = 16.971/361.631 = 0.047 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.56 > 0.20
Rmax = Pr/Pc + 8/9*[Mry/Mcy + Mrz/Mcz] = 0.948 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.002 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.121 < 1.000 ...................................................... O.K

0.02
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 52 y

0.5
Material A36 (No:1)

0.250
0.014
(Fy = 248211, Es = 199948024)
Section Name I 50b (No:45) 0.080

(Rolled : I 50b).
0.16
Member Length : 3.31667

2. Member Forces Depth 0.50000 Web Thick 0.01400

Axial Force Fxx = 0.00000 (LCB: 5, POS:I) Top F Width 0.16000 Top F Thick 0.02000
Bot.F Width 0.16000 Bot.F Thick 0.02000
Bending Moments My = -329.89, Mz = 0.00000
Area 0.01293 Asz 0.00700
End Moments Myi = -329.89, Myj = 73.4520 (for Lb) Qyb 0.08131 Qzb 0.00320
Iyy 0.00049 Izz 0.00001
Myi = -329.89, Myj = 73.4520 (for Ly) Ybar 0.08000 Zbar 0.25000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00194 Szz 0.00015
ry 0.19380 rz 0.03010
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -140.31 (LCB: 5, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 3.31667, Lz = 3.31667, Lb = 3.31667
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 110.2 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/2887.32 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 329.888/413.843 = 0.797 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/52.3269 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.797 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.135 < 1.000 ...................................................... O.K

0.022
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 54

0.63
y
Material A36 (No:1)

0.315
0.015
(Fy = 248211, Es = 199948024)
Section Name I 63b (No:46) 0.089

(Rolled : I 63b).
0.178
Member Length : 3.31667

2. Member Forces Depth 0.63000 Web Thick 0.01500

Axial Force Fxx = 0.00000 (LCB: 5, POS:I) Top F Width 0.17800 Top F Thick 0.02200
Bot.F Width 0.17800 Bot.F Thick 0.02200
Bending Moments My = -481.20, Mz = 0.00000
Area 0.01672 Asz 0.00945
End Moments Myi = -481.20, Myj = 83.5856 (for Lb) Qyb 0.12229 Qzb 0.00396
Iyy 0.00098 Izz 0.00002
Myi = -481.20, Myj = 83.5856 (for Ly) Ybar 0.08900 Zbar 0.31500
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00312 Szz 0.00020
ry 0.24230 rz 0.03250
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -194.66 (LCB: 2, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 3.31667, Lz = 3.31667, Lb = 3.31667
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 102.1 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.00/3734.86 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 481.200/675.386 = 0.712 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/71.1274 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.712 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.138 < 1.000 ...................................................... O.K

0.00635
Design Code AISC(15th)-LRFD16

0.0254
Unit System kN, m y

Member No 528
Material A36 (No:1) 0.00635

(Fy = 248211, Es = 199948024)

0.0254
Section Name RAFTER-2L1X1X1/4 (No:2)
(Built-up Section).
Member Length : 0.41438

2. Member Forces Depth 0.02540 Web Thick 0.00635

Axial Force Fxx = 47.3554 (LCB: 2, POS:I) Flg Width 0.02540 Flg Thick 0.00635
BTB Spacing 0.00000
Bending Moments My = -0.1562, Mz = -0.0032
Area 0.00056 Asz 0.00022
End Moments Myi = -0.1562, Myj = -0.1417 (for Lb) Qyb 0.00014 Qzb 0.00032
Iyy 0.00000 Izz 0.00000
Myi = -0.1562, Myj = -0.1417 (for Ly) Ybar 0.02540 Zbar 0.01678
Mzi = -0.0032, Mzj = 0.00200 (for Lz) Syy 0.00000 Szz 0.00000
ry 0.00737 rz 0.01134
Shear Forces Fyy = -0.0126 (LCB: 2, POS:1/2)
Fzz = -0.0463 (LCB: 1, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 0.41438, Lz = 0.41438, Lb = 0.41438
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 56.2 < 300.0 (LCB: 2)............................................. O.K
Axial Strength
Pr/Pc = 47.355/126.107 = 0.376 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 0.15622/0.40863 = 0.382 < 1.000 ................................... O.K
Mrz/Mcz = 0.00322/0.63872 = 0.005 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.38 > 0.20
Rmax = Pr/Pc + 8/9*[Mry/Mcy + Mrz/Mcz] = 0.720 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.001 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:04
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...\EASTGROVE\ROOF.mgb
z
1. Design Information

0.00635
Design Code AISC(15th)-LRFD16
y

0.0508
Unit System kN, m
Member No 5
Material A36 (No:1) 0.00635

(Fy = 248211, Es = 199948024)

0.0508
Section Name RAFTER-2L2X2X1/4 (No:1)
(Rolled : 2L2X2X1/4).
Member Length : 0.39459

2. Member Forces Depth 0.05080 Web Thick 0.00635

Axial Force Fxx = -138.56 (LCB: 2, POS:J) Flg Width 0.05080 Flg Thick 0.00635
BTB Spacing 0.00000
Bending Moments My = 0.00000, Mz = 0.82721
Area 0.00122 Asz 0.00043
End Moments Myi = 0.00000, Myj = 0.00000 (for Lb) Qyb 0.00064 Qzb 0.00129
Iyy 0.00000 Izz 0.00000
Myi = 0.00000, Myj = 0.00000 (for Ly) Ybar 0.05080 Zbar 0.03592
Mzi = 0.21853, Mzj = 0.81099 (for Lz) Syy 0.00001 Szz 0.00001
ry 0.01537 rz 0.02139
Shear Forces Fyy = -1.5015 (LCB: 2, POS:1/2)
Fzz = 0.02596 (LCB: 1, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 0.39459, Lz = 0.39459, Lb = 0.39459
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 25.7 < 200.0 (LCB: 2)............................................. O.K
Axial Strength
Pr/Pc = 138.565/262.210 = 0.528 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 0.00000/2.85828 = 0.000 < 1.000 ................................... O.K
Mrz/Mcz = 0.82721/2.47384 = 0.334 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.53 > 0.20
Rmax = Pr/Pc + 8/9*[Mry/Mcy + Mrz/Mcz] = 0.826 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.017 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.000 < 1.000 ...................................................... O.K

5. Deflection Checking Results

L/ 360.0 = 0.0011 > 0.0000 (Memb:5, LCB: 5, POS: 0.2m, Dir-Z)........................ O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:47
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...\EASTGROVE\ROOF.mgb
z
1. Design Information

0.02
Design Code AISI-CFSD08
Unit System kN, m 0.0018

Member No 299

0.15
y
Material A36 (No:1)

0.0750
(Fy = 248211, Es = 199948024)
0.0001
Section Name PURLINS-2''X6''X1.8mm (No:3) 0.0156

(Built-up Section).
0.05
Member Length : 3.00000

2. Member Forces Depth 0.15000 Thickness 0.00180

Axial Force Fxx = -0.2891 (LCB: 2, POS:1/2) Width 0.05000 Rounding 0.00010
Lip Depth 0.02000
Bending Moments My = 0.50804, Mz = -0.0030
Area 0.00051 Asz 0.00032
End Moments Myi = -0.1274, Myj = -0.4307 (for Lb) Qyb 0.00749 Qzb 0.00109
Iyy 0.00000 Izz 0.00000
Myi = -0.1274, Myj = -0.4307 (for Ly) Ybar 0.01557 Zbar 0.07500
Mzi = -0.0029, Mzj = -0.0029 (for Lz) Syy 0.00002 Szz 0.00001
ry 0.05818 rz 0.01895
Shear Forces Fyy = 0.00000 (LCB: 1, POS:1/2)
Fzz = 0.10111 (LCB: 2, POS:1/2)

3. Design Parameters
Unbraced Lengths Ly = 3.00000, Lz = 3.00000, Lb = 3.00000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 158.3 < 200.0 (LCB: 2)............................................. O.K
Axial Strength
Pu/Pa = 0.2891/18.5023 = 0.016 < 1.000 ..................................... O.K
Bending Strength
Muy/May = 0.50804/1.72966 = 0.294 < 1.000 ...................................... O.K
Muz/Maz = 0.00298/0.70312 = 0.004 < 1.000 ...................................... O.K
Combined Strength (Compression+Bending)
Pu/Pa = 0.02 < 0.15
Rmax = Pu/Pa + My/May + Mz/Maz = 0.313 < 1.000 ................................... O.K
Shear Strength
Vuy/Vay = 0.000 < 1.000 ...................................................... O.K
Vuz/Vaz = 0.161 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:13
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-06-11-25.mgb
z
1. Design Information

0.002
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 2940

0.05
y
Material A36 (No:1)
(Fy = 248211, Es = 199948024)
Section Name CANOPY-2''x2''x2mm (No:40) 0.002

(Built-up Section).
0.05
Member Length : 3.50000

2. Member Forces Depth 0.05000 Web Thick 0.00200

Axial Force Fxx = 0.00000 (LCB: 2, POS:1/2) Flg Width 0.05000 Top F Thick 0.00200
Web Center 0.04800 Bot.F Thick 0.00200
Bending Moments My = 1.02314, Mz = 0.00000
Area 0.00038 Asz 0.00020
End Moments Myi = -0.3209, Myj = -0.5800 (for Lb) Qyb 0.00086 Qzb 0.00086
Iyy 0.00000 Izz 0.00000
Myi = -0.3209, Myj = -0.5800 (for Ly) Ybar 0.02500 Zbar 0.02500
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00001 Szz 0.00001
ry 0.01961 rz 0.01961
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = 1.63379 (LCB: 2, POS:J)

3. Design Parameters
Unbraced Lengths Ly = 3.50000, Lz = 3.50000, Lb = 3.50000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 178.5 < 300.0 (LCB: 17)............................................. O.K
Axial Strength
Pr/Pc = 0.0000/85.7818 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 1.02314/1.53796 = 0.665 < 1.000 ................................... O.K
Mrz/Mcz = 0.00000/1.54497 = 0.000 < 1.000 ................................... O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.066 < 1.000 ...................................................... O.K
Torsion Strength
Tr/Tc = 0.25234/1.23112 = 0.205 < 1.000 ...................................... O.K
Combined Strength (Tension+Bending+Shear+Torsion)
Tr/Tc = 0.20 > 0.20
Rmax1 = Pr/Pc + Mry/Mcy + [Vrz/Vcz + Tr/Tc]^2
Rmax2 = Pr/Pc + Mrz/Mcz + [Vry/Vcy + Tr/Tc]^2
Rmax = MAX[ Rmax1, Rmax2 ] = 0.709 < 1.000 ...................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:10
http://www.MidasUser.com
Gen 2021
midas Gen Steel Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-06-11-25.mgb
z
1. Design Information

0.0158
Design Code AISC(15th)-LRFD16
Unit System kN, m
Member No 1857

0.36
y
Material A36 (No:1)

0.180
0.014
(Fy = 248211, Es = 199948024)
Section Name CANOPY (No:41) 0.070

(Rolled : I 36c).
0.14
Member Length : 0.60000

2. Member Forces Depth 0.36000 Web Thick 0.01400

Axial Force Fxx = 0.00000 (LCB: 2, POS:I) Top F Width 0.14000 Top F Thick 0.01580
Bot.F Width 0.14000 Bot.F Thick 0.01580
Bending Moments My = -234.40, Mz = 0.00000
Area 0.00908 Asz 0.00504
End Moments Myi = -234.40, Myj = -196.18 (for Lb) Qyb 0.04067 Qzb 0.00245
Iyy 0.00017 Izz 0.00001
Myi = -234.40, Myj = -196.18 (for Ly) Ybar 0.07000 Zbar 0.18000
Mzi = 0.00000, Mzj = 0.00000 (for Lz) Syy 0.00096 Szz 0.00009
ry 0.13820 rz 0.02600
Shear Forces Fyy = 0.00000 (LCB: 3, POS:1/2)
Fzz = -64.100 (LCB: 2, POS:I)

3. Design Parameters
Unbraced Lengths Ly = 0.60000, Lz = 0.60000, Lb = 0.60000
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 1.00
4. Checking Results
Slenderness Ratio
L/r = 23.1 < 300.0 (Memb:1857, LCB: 2).................................. O.K
Axial Strength
Pr/Pc = 0.00/2029.28 = 0.000 < 1.000 ..................................... O.K
Bending Strength
Mry/Mcy = 234.403/254.404 = 0.921 < 1.000 ................................... O.K
Mrz/Mcz = 0.0000/31.3461 = 0.000 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.00 < 0.20
Rmax = Pr/(2*Pc) + [Mry/Mcy + Mrz/Mcz] = 0.921 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.000 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.085 < 1.000 ...................................................... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:54
http://www.MidasUser.com
Gen 2021
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

1. General Information
Design Code Code Unit Section Fck Fy Fys
ACI318-14 lbf,in 0.250x0.500 20,684KPa 227,600KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Forces and Reinforcement

SECT. Mu,top Mu,bot Vu Top Bar Bot Bar Stirrup
End(I) 62.00kN·m 37.98kN·m 31.98kN 4-#5 4-#5 2-#[email protected]
Middle 28.79kN·m 35.35kN·m 26.68kN 4-#5 4-#5 2-#[email protected]
End(J) 58.99kN·m 55.49kN·m 25.61kN 4-#5 4-#5 2-#[email protected]

0.250
0.0400

0.500
0.0400

End(I) Middle End(J)

3. Check Bending Moment Capacity

SECT. End(I) Middle End(J)
POS. Top Bot Top Bot Top Bot
β1 0.850 0.850 0.850 0.850 0.850 0.850
s(m) 0.135 0.135 0.135 0.135 0.135 0.135
smax(m) 0.554 0.554 0.554 0.554 0.554 0.554
ρmax 0.0281 0.0281 0.0281 0.0281 0.0281 0.0281
ρ 0.00758 0.00758 0.00758 0.00758 0.00758 0.00758
ρmin 0.00606 0.00571 0.00430 0.00531 0.00606 0.00606
ø 0.900 0.900 0.900 0.900 0.900 0.900
ρεt 0.0281 0.0281 0.0281 0.0281 0.0281 0.0281
øMn(kN·m) 65.74 65.74 65.74 65.74 65.74 65.74
Ratio 0.943 0.578 0.438 0.538 0.897 0.844

4. Check Shear Capacity

Vs Av.min Av.req Smax Sreq s øVn
SECT. Ratio
(kN) (m²) (m²) (m) (m) (m) (kN)
End(I) 0.000 0.00000962 0.000 0.211 0.375 0.100 162 0.197
Middle 0.000 0.00000962 0.000 0.211 0.211 0.200 111 0.241
End(J) 0.000 0.00000962 0.000 0.211 0.211 0.100 162 0.158

2025-07-01 17:37 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

1. General Information
Design Code Code Unit Section Fck Fy Fys
ACI318-14 lbf,in 0.300x0.600 20,684KPa 227,600KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Forces and Reinforcement

SECT. Mu,top Mu,bot Vu Top Bar Bot Bar Stirrup
End(I) 96.43kN·m 28.35kN·m 35.14kN 5-#5 4-#5 2-#[email protected]
Middle 17.68kN·m 34.12kN·m 20.56kN 3-#5 4-#5 2-#[email protected]
End(J) 79.64kN·m 17.65kN·m 34.44kN 5-#5 4-#5 2-#[email protected]

0.300
0.0400

0.600
0.0400

End(I) Middle End(J)

3. Check Bending Moment Capacity

SECT. End(I) Middle End(J)
POS. Top Bot Top Bot Top Bot
β1 0.850 0.850 0.850 0.850 0.850 0.850
s(m) 0.0925 0.0617 0.0925 0.0617 0.0925 0.0617
smax(m) 0.554 0.554 0.554 0.554 0.554 0.554
ρmax 0.0281 0.0281 0.0281 0.0281 0.0281 0.0281
ρ 0.00634 0.00492 0.00369 0.00492 0.00634 0.00492
ρmin 0.00606 0.00211 0.00131 0.00255 0.00606 0.00131
ø 0.900 0.900 0.900 0.900 0.900 0.900
ρεt 0.0281 0.0281 0.0281 0.0281 0.0281 0.0281
øMn(kN·m) 103 86.08 65.09 86.08 103 86.08
Ratio 0.933 0.329 0.272 0.396 0.771 0.205

4. Check Shear Capacity

Vs Av.min Av.req Smax Sreq s øVn
SECT. Ratio
(kN) (m²) (m²) (m) (m) (m) (kN)
End(I) 0.000 0.0000115 0.000 0.263 0.263 0.100 217 0.162
Middle 0.000 0.0000115 0.000 0.271 0.271 0.200 158 0.130
End(J) 0.000 0.0000115 0.000 0.263 0.263 0.100 217 0.159

2025-07-04 21:03 1
midas Gen RC Beam Strength Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-06-08-25.mgb

1. Design Information
Design Code NSCP 2015 Unit System kN, m
Material Data fc = 20684.3, fy = 275790, fys = 275790 KPa
Section Property B-1 (No : 12) Beam Span 7.275m

[END-I] [MID] [END-J]

0.0762

0.0762
0.8

0.8

0.8
0.0762

0.0762

0.0762
0.4 0.4 0.4

TOP 5-P32/ 2-P20 TOP 3-P32/ 2-P20 TOP 5-P32/ 2-P20

BOT 3-P32/ 2-P25 BOT 5-P32/ 2-P20 BOT 3-P32/ 2-P25
STIRRUPS 2-P10 @100 STIRRUPS 2-P10 @100 STIRRUPS 2-P10 @100

2. Bending Moment Capacity

END-I MID END-J
(-) Load Combination No. 9 19 7
Moment (Mu) 688.27 288.53 691.94
Factored Strength (phiMn) 742.26 495.69 742.26
Check Ratio (Mu/phiMn) 0.9273 0.5821 0.9322

(+) Load Combination No. 19 9 21

Moment (Mu) 514.36 305.62 524.56
Factored Strength (phiMn) 546.30 748.22 546.30
Check Ratio (Mu/phiMn) 0.9415 0.4085 0.9602

Using Rebar Top (As_top) 0.0046 0.0030 0.0046

Using Rebar Bot (As_bot) 0.0034 0.0046 0.0034

3. Shear Capacity
END-I MID END-J
Load Combination No. 9 9 7
Factored Shear Force (Vu) 237.16 209.79 235.89
Shear Strength by Conc.(phiVc) 163.02 163.02 163.02
Shear Strength by Rebar.(phiVs) 232.93 232.93 232.93
Using Shear Reinf. (AsV) 0.0016 0.0016 0.0016
Using Stirrups Spacing 2-P10 @100 2-P10 @100 2-P10 @100
Check Ratio 0.5990 0.5298 0.5957

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:57
http://www.MidasUser.com
Gen 2021
Client ALLENCO Calculation By
Project Name PROPOSED 3-STOREY COMMERCIAL BUILDING Company Name
Project Ref. Date 14-07-2025
Slab Ref. Location
Comments
Revision

1 Overall Summary
Construction Stage PASS Max. UF 0.91
Composite Stage PASS Max. UF 0.57
Fire Stage PASS Max. UF 0.00

2 Input Parameters
2.1 Deck/Span Properties
Deck Type TR60+, 0.9mm, S350 Span 3.00m
Span Type Single Support Width 100mm
Number of Props N/A Prop Width N/A

2.2 Slab Properties

Slab Depth 125mm Concrete Type C25/30
Slab Type Continuous (End) Wet/Dry Density 2550/2450 kg/m³
Concrete Volume 0.09m³/m² Modular Ratio 16.47
Specified Mesh A142 Specified Bar 12mm, 1 per trough
Mesh Yield Strength 250 N/mm² Bar Yield Strength 250 N/mm²

2.3 Loadings SLS (kN/m²) ULS (kN/m²)

Concrete Weight (wet) 2.28 3.64
Deck + Reinforcement 0.15 0.18
Total Slab (Construction Stage) 2.42 3.82
Construction Load 1.50 2.40
Dead Load 3.50 4.20
Live Load 2.40 3.84
Total Selfweight 2.33 2.80

2.4 Concentrated Loading

Name Type Live Dead Total ULS Finishes Width Location Length Start Finish
No concentrated loading

3 Design Criteria
Fire Period 0.5 hrs Fire Analysis Method EC (Mesh & Bar)
Live Load Factor 1.60 Dead Load Factor 1.20
Superimposed Load Factor 1.20 ψ0 Factor 0.70
ψ1 Factor 0.70 ψ2 Factor 0.60

4 Construction Stage
Applied Capacity/Limit Unity Factor
Web Shear 9.20 kN/m 52.76 kN/m 0.17
Web Crushing 9.20 kN/m 10.67 kN/m 0.86
Bending (Sagging) 6.81 kNm/m 7.50 kNm/m 0.91
Deflection 12.3 mm 16.4 mm 0.75
(Deflection limit is the lesser of Span/180 and 20mm)

5 Composite Stage
Average Composite Inertia 7222976 mm4
Applied Capacity/Limit Unity Factor
Vertical Shear 16.54 kN/m 58.65 kN/m 0.28
Bending Resistance 11.92 kNm/m 30.31 kNm/m 0.39
Imposed Load Deflection 1.6 mm 8.3 mm 0.20
(Deflection limit is the lesser of Span/360 and 20 mm)
Total Load Deflection[5] 4.1 mm 12.5 mm 0.33
(Deflection limit is the lesser of Span/240.00 and 20.00 mm)
Dynamic Deflection 0.27 mm[1]
Slab Natural Frequency 8.76 Hz 5.00Hz 0.57

6 Fire Stage
Applied Capacity/Limit Unity Factor
Moment Resistance 7.88 kNm/m 7.46 kNm/m 0.00[3]

7 LCA - Embodied Carbon[4]

Deck Deck & Concrete
Concrete kgCO₂e/kg
kgCO₂e/kg kgCO₂e/m²
Product A1 – A3 2.520 0.200 70.741
Deconstruction C1 0.020 0.006 1.476
Transport C2 0.040 0.004 1.356
Waste Processing C3 0.000 0.002 0.501
End of Life C4 0.000 -0.004 -0.911
Reuse, recovery, recycling D -1.450 -0.031 -21.639
Total 1.130 0.177 51.524

Notes

• This calculation is based on slab poured to the constant thickness specified. No account is taken for any additional concrete weight
as a result of deflection of the supporting structure.

• Where "calculated minimum" is chosen for reinforcement, values represent minimum design code requirements. These may need to
be increased for other purposes (e.g. crack control, transverse reinforcement for composite beams etc.)

• This calculation does not consider any reinforcement requirements not associated with composite action between deck and concrete
(e.g. cantilever, void trimming etc.). These should be specified separately.

[1] This figure represents the dynamic deflection of the slab only. This should be added to the dynamic deflection of supporting beams when
considering natural frequency of floor plate (Refer SCI P-354)
[3] No fire stage moment resistance or unity factor is reported for a fire period of 0.5 hours. In accordance with the design standard the
composite stage design (at ambient temperature) is deemed to satisfy this requirement.
[4] The figures calculated are based on the values for steel deck and typical RC30 concrete with 2% reinforcement as published by BCSA, for
the relevant references refer steelconstruction.info/Life_cycle_assessment_and_embodied_carbon.
[5] This value is for composite stage deflection of the slab only. If the total deflection of the sheet from install position is required, the applied
construction stage deflection value from section 4 should be added to this value.

Generated using SMD Elements® version 3.1.1.1

Client ALLENCO Calculation By
Project Name PROPOSED 3-STOREY COMMERCIAL BUILDING Company Name
Project Ref. Date 14-07-2025
Slab Ref. Location
Comments
Revision

1 Overall Summary
Construction Stage FAIL Max. UF 1.70
Composite Stage PASS Max. UF 0.97
Fire Stage PASS Max. UF 0.00

2 Input Parameters
2.1 Deck/Span Properties
Deck Type TR60+, 0.9mm, S350 Span 3.82m
Span Type Single Support Width 100mm
Number of Props N/A Prop Width N/A

2.2 Slab Properties

2.3 Loadings SLS (kN/m²) ULS (kN/m²)

Concrete Weight (wet) 2.28 3.64
Deck + Reinforcement 0.15 0.18
Additional slab due to ponding 0.57 0.92
Total Slab (Construction Stage) 3.00 4.74
Construction Load 1.50 2.40
Dead Load 3.50 4.20
Live Load 2.40 3.84
Total Selfweight 2.89 3.46

2.4 Concentrated Loading

Name Type Live Dead Total ULS Finishes Width Location Length Start Finish
No concentrated loading

3 Design Criteria
Fire Period 0.5 hrs Fire Analysis Method EC (Mesh & Bar)
Live Load Factor 1.60 Dead Load Factor 1.20
Superimposed Load Factor 1.20 ψ0 Factor 0.70
ψ1 Factor 0.70 ψ2 Factor 0.60

4 Construction Stage
Applied Capacity/Limit Unity Factor
Web Shear 13.49 kN/m 52.76 kN/m 0.26
Web Crushing 13.49 kN/m 10.67 kN/m 1.26
Bending (Sagging) 12.75 kNm/m 7.50 kNm/m 1.70
Deflection 40.6 mm 29.1 mm 1.40
(Deflection limit is the lesser of Span/130 and 30mm)

5 Composite Stage
Average Composite Inertia 7222976 mm4
Applied Capacity/Limit Unity Factor
Vertical Shear 22.36 kN/m 58.65 kN/m 0.38
Bending Resistance 20.89 kNm/m 31.50 kNm/m 0.66
Imposed Load Deflection 4.3 mm 10.6 mm 0.41
(Deflection limit is the lesser of Span/360 and 20 mm)
Total Load Deflection[5] 10.7 mm 15.9 mm 0.67
(Deflection limit is the lesser of Span/240.00 and 20.00 mm)
Dynamic Deflection 0.77 mm[1]
Slab Natural Frequency 5.17 Hz 5.00Hz 0.97

6 Fire Stage
Applied Capacity/Limit Unity Factor
Moment Resistance 13.92 kNm/m 7.46 kNm/m 0.00[3]

7 LCA - Embodied Carbon[4]

Deck Deck & Concrete
Concrete kgCO₂e/kg
kgCO₂e/kg kgCO₂e/m²
Product A1 – A3 2.520 0.200 81.995
Deconstruction C1 0.020 0.006 1.791
Transport C2 0.040 0.004 1.593
Waste Processing C3 0.000 0.002 0.625
End of Life C4 0.000 -0.004 -1.136
Reuse, recovery, recycling D -1.450 -0.031 -23.406
Total 1.130 0.177 61.461

Notes

• This calculation is based on slab poured to the constant thickness specified. No account is taken for any additional concrete weight
as a result of deflection of the supporting structure.

Generated using SMD Elements® version 3.1.1.1

MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BS1

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
0.000kN 2.100kN·m 1.000kN·m

(2) Factored Load

Pu Mux Muy
0.000kN 5.900kN·m 2.000kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - - -

3. Foundation
Depth Cover Lx Ly fe
0.200m 0.0800m 12.00m 12.00m 80.00kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.000m 0.000m 0.000m 0.000m

2025-07-14 11:59 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BS1

6.00 6.00 6.00

Y1
6.00

X1
0.20

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 4.566 80.00 0.0571
qu,max (kN/m²) 5.494 - -
qu,min (kN/m²) 5.439 - -
One Way Shear-X (kN) 0.000 783 0.000
One Way Shear-Y (kN) 0.000 719 0.000
Two Way Shear (kN) 0.000 60.18 0.000
Moment-X Direction(Muy, kN·m/m) 0.0254 5.878 0.00432
Moment-Y Direction(Mux, kN·m/m) 0.0749 5.419 0.0138
Rebar Space-Y Direction(sx, m) 0.170 0.457 0.372
Rebar Space-X Direction(sy, m) 0.170 0.457 0.372

2025-07-14 11:59 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : RAMP SLAB

1. General Information
Design Code Code Unit Span(X) Span(Y) THK. F'c Fy
ACI318-14 lbf, in 7.000m 12.00m 0.300m 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Load & Support Condition

Dead Load Live Load Slab Type Support Type
3.500kN/m² 4.800kN/m² 2-Way Slab Support Case-2

y
x
B1

Y1
Lx

Y2
B3

X1 X2

3. Check Thickness & Deflection

Check Items Input Criteria Ratio
Required minimum thickness (m) 0.300 0.238 0.793

4. Check Moment & Shear Capacity [ Direction X ]

Check Items TOP MIDDLE BOTTOM
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Mu (kN·m/m) 573 353 573
Vu (kN/m) 449 0.000 449
øMn (kN·m/m) 653 653 653
øVn (kN/m) 1,849 1,849 1,849
Mu / øMn 0.878 0.541 0.878
Vu / øVn 0.243 0.000 0.243

5. Check Moment & Shear Capacity [ Direction Y ]

Check Items LEFT CENTER RIGHT
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -

2025-07-01 18:50 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : RAMP SLAB

Mu (kN·m/m) 184 115 184

Vu (kN/m) 85.36 0.000 85.36
øMn (kN·m/m) 614 614 614
øVn (kN/m) 1,741 1,741 1,741
Mu / øMn 0.300 0.187 0.300
Vu / øVn 0.0490 0.000 0.0490

2025-07-01 18:50 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : ST01

1. General Information
Design Code Code Unit F'c Fy Fys
ACI318-14 lbf,in 20,684KPa 227,600KPa 400,000KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Load & Support Condition

Design Load Support
DLstair DLlanding LL Type Left Right
3.500kN/m² 3.500kN/m² 2.400kN/m² By Landing Pin(0.000) Pin(0.000)

3. Section
Thickness Length Size
Stair Landing Cover Landing(L) Landing(R) Stair Height Width
0.150m 0.125m 0.0200m 1.950m 1.950m 6.000m 2.000m 1.800m
2.000
0.900 0.900
1.800

1.950 6.000 1.950

4. Moment Diagram
Mu = 0.000

Vu = 7.352

Vu = 0.000

Mu = 11.62
Vu = -5.782 Vu = -7.352

Mu = 0.000
Vu = 0.000
Mu = 0.000 Mu = 0.000
Mu = 2.602
Vu = 5.782

5. Shear Force Diagram

Mu = 0.000

Vu = 7.352

Vu = 0.000

Mu = 11.62
Vu = -5.782 Vu = -7.352

Mu = 0.000
Vu = 0.000
Mu = 0.000 Mu = 0.000
Mu = 2.602
Vu = 5.782

6. Check Stair
(1) Moment Capacity
Rebar Land(L) Stair Land(R) Min. Land Min. Stair
Mu (kN·m/m) 2.602 11.62 2.602 ρ = 0.00200 ρ = 0.00200

2025-07-01 18:37 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : ST01

#3 @0.166 @0.0437 @0.166 @0.457(0.554) @0.457(0.554)

#3+4 @0.230 @0.0607 @0.230 @0.457(0.554) @0.457(0.554)
#4 @0.297 @0.0783 @0.297 @0.457(0.554) @0.457(0.554)
#4+5 @0.372 @0.0983 @0.372 @0.457(0.554) @0.457(0.554)
#5 @0.452 @0.119 @0.452 @0.457(0.554) @0.457(0.554)

(2) Shear Capacity

- Land(L) Stair Land(R)
Vu (kN/m) -5.782 -7.352 5.782
øVn (kN/m) 15.94 19.70 15.94
Vu / øVn 0.363 0.373 0.363

2025-07-01 18:37 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

1. General Information
Design Code Code Unit F'c Fy Fys
ACI318-14 lbf, in 20,684KPa 227,600KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Section
Basewall Type Cover Width of Basewall
1 Way 0.0400m -

- Name H(m) THK.(m)

1 B1 3.000 0.200

3. Boundary Condition
Top Bottom Left Right
Pin(0.000) Fix(1.000) - -

4. Load
Surcharge 1st Floor Level Water Level Live Factor Soil Factor Water Factor
0.000kip/ft² GL+0.000ft GL+0.000ft 1.600 1.600 1.600

No. H(ft) Angle Density(kip/ft³)

1 32.81 30.00 0.115
2 32.81 30.00 0.115
3 32.81 30.00 0.115
4 32.81 30.00 0.115
5 32.81 30.00 0.115
6 32.81 30.00 0.115
7 32.81 30.00 0.115
8 32.81 30.00 0.115

1F
G.L GL0
3.000 ( t = 0.200 )

5. Calculate soil pressure

Level Press.
Posi. Ko Equation
( ft ) ( kip/ft² )
Layer-01 Top 0.500 0.000 1.600x0.500x0.000 + 1.600x0.500x0.000 0.000
Layer-01 Bot 0.500 32.81 1.600x0.500x0.000 + 1.600x0.500x1.711 + 1.600x2.048 4.646

2025-07-01 18:40 1
MIDASIT http://www.midasuser.com

RC BASEWALL LIST

BASEWALL DETAIL ( BW1 )

1F GL0.000
GL

#5@150 #4@200
3000 (t=200)

#4@200 #4@200
1000

B1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

Layer-02 Top 0.500 32.81 1.600x0.500x0.000 + 1.600x0.500x1.711 + 1.600x2.048 4.646

Layer-02 Bot 0.500 65.62 1.600x0.500x0.000 + 1.600x0.500x3.422 + 1.600x4.096 9.292
Layer-03 Top 0.500 65.62 1.600x0.500x0.000 + 1.600x0.500x3.422 + 1.600x4.096 9.292
Layer-03 Bot 0.500 98.43 1.600x0.500x0.000 + 1.600x0.500x5.134 + 1.600x6.144 13.94
Layer-04 Top 0.500 98.43 1.600x0.500x0.000 + 1.600x0.500x5.134 + 1.600x6.144 13.94
Layer-04 Bot 0.500 131 1.600x0.500x0.000 + 1.600x0.500x6.845 + 1.600x8.193 18.58
Layer-05 Top 0.500 131 1.600x0.500x0.000 + 1.600x0.500x6.845 + 1.600x8.193 18.58
Layer-05 Bot 0.500 164 1.600x0.500x0.000 + 1.600x0.500x8.556 + 1.600x10.24 23.23
Layer-06 Top 0.500 164 1.600x0.500x0.000 + 1.600x0.500x8.556 + 1.600x10.24 23.23
Layer-06 Bot 0.500 197 1.600x0.500x0.000 + 1.600x0.500x10.27 + 1.600x12.29 27.88
Layer-07 Top 0.500 197 1.600x0.500x0.000 + 1.600x0.500x10.27 + 1.600x12.29 27.88
Layer-07 Bot 0.500 230 1.600x0.500x0.000 + 1.600x0.500x11.98 + 1.600x14.34 32.52
Layer-08 Top 0.500 230 1.600x0.500x0.000 + 1.600x0.500x11.98 + 1.600x14.34 32.52
Layer-08 Bot 0.500 262 1.600x0.500x0.000 + 1.600x0.500x13.69 + 1.600x16.39 37.17

1F( GL+0.000 ) GL0 G.L

γ = 18.00
3.000

ф = 30.00
Ko = 0.500

B1( GL-3.000 )
66.74

[ Unit ] kN/m² γ : kN/m³

6. Check Moment Capacity [ Direction Y ]

Mu = 0.000

Mu = 5.460

Mu = -12.17

(1) Story : B1
- Top Center Bottom Remark
Rebar1 #[email protected] #[email protected] #[email protected] -
Rebar2 - - #[email protected] -

2025-07-01 18:40 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

Layer(s) -
Mu(kN·m/m) 1.214 5.460 -12.17 -
øMn(kN·m/m) 5.445 10.88 15.63 -
Ratio 0.223 0.502 0.778 -
Rebar Length(m) - - 0.400 -
Rebar Space(m) 0.361 0.271 0.158 smax = 0.554m

7. Check Shear Capacity [ Direction Y ]

Vu = -6.115
Vu = -5.979

Vu = 20.46
Vu = 24.40

(1) Story : B1
- Top Center Bottom Remark
Vu(kN/m) -6.115 - 24.40 -
Vucritical -5.979 - 20.46 -
øVc(kN/m) 24.34 - 24.34 -
øVs(kN/m) 0.000 - 0.000 -
øVn(kN/m) 24.34 - 24.34 -
Ratio 0.246 - 0.841 -
Rebar - - - -
Reinf. Length(m) - - - -

2025-07-01 18:40 3
midas Gen RC Wall Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-07-12-25.mgb
1. Design Condition
Design Code : NSCP 2015 Unit System : kN, m
Wall ID : 2 (Wall Mark : wM0002)
Story : 1F (Height = 6 m)
0.0508
Material Data : fc = 20684.3, fy = 275790, fys = 275790 KPa
Wall Dim. (Length*Thk) : 12*0.15 m

0.15
0.0508
Vertical Rebar : P12 @100 (AsV = 0.00226 m^2/m)

2. Axial and Moments Capacity 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Concentric Max. Axial Load phiPn-max = 20101.0 kN

y (LCB : 13, POS : I) z (LCB : 13, POS : I)

Pu (kN) 1325.76 1325.76

phiPn (kN) 20101.0 0.00000
Check Ratio (Pu / phiPn) 0.066 < 1.000 ....... O.K 0.000 < 1.000 ....... O.K
Mc (kN-m) -940.84 0.00000
phiMn (kN-m) 15742.4 0.00000
Check Ratio (Mc / phiMn) 0.060 < 1.000 ....... O.K 0.000 < 1.000 ....... O.K

P(kN)
40000
P(kN)
40000

35250 Major Axis 35250 Minor Axis

30500 30500

25750 25750

21000 21000
20101 20101
(20101,15742)
16250 16250

11500 11500

6750 6750

2000 2000
0 (1326,941) 0 (1326,0)
-2750 M(kN-m) -2750 (0,0)
M(kN-m)
-7500 -7500
14000

21000

28000

35000

42000

49000

56000

63000

70000
7000

150

225

300

375

450

525

600

675

750
75

0 0

3. Shear Capacity
Applied Shear Force Vu = 619.895 kN (Load Combination : 5)
Design Shear Strength phiVc+phiVs = 1423.59 + 2653.24 = 4076.82 kN
(As-H_req = 0.00181 m^2/m, P12 @125)
Shear Ratio Vu/phiVn = 0.152 < 1.000 ....... O.K

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/14/2025 13:32
http://www.MidasUser.com
Gen 2021
midas Gen RC Column Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...Eastgrove China-07-12-25.mgb
1. Design Condition z
Design Code : NSCP 2015 UNIT SYSTEM: kN, m
Member Number: 1776
Material Data : fc = 20684.3, fy = 275790, fys = 275790 KPa
Column Height : 3.2 m
Section Property: 110x900 (No : 56)
y

1.1
Rebar Pattern : 16 - 5 - P32 Ast = 0.012868 m^2 (Rhost = 0.013)

2. Axial and Moments Capacity

0.0762
Load Combination : 13 (Pos : J)
Concentric Max. Axial Load phiPn-max = 10778.8 kN 0.9
Axial Load Ratio Pu / phiPn = 2676.12 / 8506.11 = 0.315 < 1.000 ....... O.K
Moment Ratio Mc / phiMn = 594.349 / 1913.28 = 0.311 < 1.000 ....... O.K
Mcy / phiMny = -592.99 / 1909.04 = 0.311 < 1.000 ....... O.K
Mcz / phiMnz = -40.164 / 127.333 = 0.315 < 1.000 ....... O.K

P-M Interaction Diagram

P(kN)
22500
phiPn(kN) phiMn(kN-m)
19750 Theta=3.82Deg.
N.A=7.24Deg. 13473.49 0.00
17000 12274.25 652.78
14250 10802.26 1253.61
9436.06 1683.33
11500
10779 8208.27 1978.02
8750 7206.31 2168.26
(8506,1913)
6000 6632.53 2260.65
3250
6189.17 2402.47
(2676,594) 5459.21 2575.22
500
0 4416.22 2725.75
-2250 M(kN-m) 2607.38 2507.31
-5000 -197.78 1464.84
1200

1600

2000

2400

2800

3200

3600

4000

-3193.98 0.00
400

800

3. Shear Capacity
[ END ] y (LCB : 14, POS : I) z (LCB : 23, POS : I)
Applied Shear Force (Vu) 80.6880 kN 304.806 kN
Design Shear Strength (phiVc+phiVs)609.372 + 178.440 = 787.812 kN 565.208 + 221.761 = 786.969 kN
Shear Ratio 0.102 < 1.000 ....... O.K 0.387 < 1.000 ....... O.K
As-H_use 0.00105 m^2/m, 2-P10 @150 0.00105 m^2/m, 2-P10 @150

[ MIDDLE ] y (LCB : 14, POS : 1/2) z (LCB : 23, POS : 1/2)

Applied Shear Force (Vu) 80.6880 kN 304.806 kN
Design Shear Strength (phiVc+phiVs)611.037 + 178.440 = 789.477 kN 566.477 + 221.761 = 788.238 kN
Shear Ratio 0.102 < 1.000 ....... O.K 0.387 < 1.000 ....... O.K
As-H_use 0.00105 m^2/m, 2-P10 @150 0.00105 m^2/m, 2-P10 @150

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/15/2025 21:03
http://www.MidasUser.com
Gen 2021
midas Gen RC Column Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...rove China-roof-07-01-25.mgb
1. Design Condition z
Design Code : NSCP 2015 UNIT SYSTEM: kN, m
Member Number: 1008
Material Data : fc = 20684.3, fy = 275790, fys = 275790 KPa
Column Height : 2.5 m
Section Property: 55x55 (No : 9)

0.55
Rebar Pattern : 14 - 5 - P25(P32) Ast = 0.0081257 m^2 (Rhost = 0.027) y

2. Axial and Moments Capacity

0.0635
Load Combination : 22 (Pos : J)
Concentric Max. Axial Load phiPn-max = 3856.62 kN 0.55
Axial Load Ratio Pu / phiPn = 83.0421 / 85.7498 = 0.968 < 1.000 ....... O.K
Moment Ratio Mc / phiMn = 448.837 / 456.937 = 0.982 < 1.000 ....... O.K
Mcy / phiMny = -174.02 / 179.636 = 0.969 < 1.000 ....... O.K
Mcz / phiMnz = -413.73 / 420.146 = 0.985 < 1.000 ....... O.K

P-M Interaction Diagram

P(kN)7500
phiPn(kN) phiMn(kN-m)
6525 Theta=66.85Deg.
N.A=67.19Deg. 4820.77 0.00
5550 4534.63 91.93
4575 4098.05 187.66
3857 3510.37 285.37
3600
2927.65 360.23
2625 2438.82 409.75
1650 2144.25 433.27
675
1905.40 462.53
0 1418.82 500.65
-300 (83,449)
(86,457)
M(kN-m) 766.40 502.08
-1275 -287.60 395.95
-2250 -1482.55 157.12
-2016.89 0.00
140

210

280

350

420

490

560

630

700
70

3. Shear Capacity
[ END ] y (LCB : 10, POS : I) z (LCB : 5, POS : I)
Applied Shear Force (Vu) 123.949 kN 92.4472 kN
Design Shear Strength (phiVc+phiVs)157.204 + 158.068 = 315.273 kN 111.033 + 158.068 = 269.101 kN
Shear Ratio 0.393 < 1.000 ....... O.K 0.344 < 1.000 ....... O.K
As-H_use 0.00157 m^2/m, 2-P10 @100 0.00157 m^2/m, 2-P10 @100

[ MIDDLE ] y (LCB : 10, POS : 1/2) z (LCB : 5, POS : 1/2)

Applied Shear Force (Vu) 123.949 kN 92.4472 kN
Design Shear Strength (phiVc+phiVs)157.589 + 158.068 = 315.657 kN 112.592 + 158.068 = 270.660 kN
Shear Ratio 0.393 < 1.000 ....... O.K 0.342 < 1.000 ....... O.K
As-H_use 0.00157 m^2/m, 2-P10 @100 0.00157 m^2/m, 2-P10 @100

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:48
http://www.MidasUser.com
Gen 2021
midas Gen RC Column Checking Result
Company Integritus Consultancy Project Title
Author asus File Name E:\...rove China-roof-07-01-25.mgb
1. Design Condition z
Design Code : NSCP 2015 UNIT SYSTEM: kN, m
Member Number: 1027
Material Data : fc = 20684.3, fy = 275790, fys = 275790 KPa
Column Height : 3.5 m
Section Property: 80x85 (No : 8)

0.85
Rebar Pattern : 12 - 4 - P32 Ast = 0.009651 m^2 (Rhost = 0.014) y

2. Axial and Moments Capacity

0.0762
Load Combination : 19 (Pos : J)
Concentric Max. Axial Load phiPn-max = 7512.69 kN 0.8
Axial Load Ratio Pu / phiPn = 423.739 / 1216.74 = 0.348 < 1.000 ....... O.K
Moment Ratio Mc / phiMn = 419.312 / 1218.58 = 0.344 < 1.000 ....... O.K
Mcy / phiMny = 403.964 / 1175.01 = 0.344 < 1.000 ....... O.K
Mcz / phiMnz = -112.41 / 322.907 = 0.348 < 1.000 ....... O.K

P-M Interaction Diagram

P(kN)
15000
phiPn(kN) phiMn(kN-m)
13000 Theta=15.37Deg.
N.A=16.71Deg. 9390.87 0.00
11000 8867.39 246.73
9000 7953.16 553.91
7513 6846.94 834.03
7000
5858.15 1019.90
5000 5051.48 1132.91
3000 4589.43 1184.58
1000
4220.80 1262.75
0 (424,419)
(1217,1219) 3524.35 1363.41
-1000 M(kN-m) 2576.01 1389.93
-3000 915.09 1140.71
-5000 -1305.51 474.38
1000

1200

1400

1600

1800

2000

-2395.49 0.00
200

400

600

800

3. Shear Capacity
[ END ] y (LCB : 7, POS : I) z (LCB : 7, POS : I)
Applied Shear Force (Vu) 79.8843 kN 132.393 kN
Design Shear Strength (phiVc+phiVs)384.149 + 235.169 = 619.318 kN 386.528 + 251.414 = 637.942 kN
Shear Ratio 0.129 < 1.000 ....... O.K 0.208 < 1.000 ....... O.K
As-H_use 0.00157 m^2/m, 2-P10 @100 0.00157 m^2/m, 2-P10 @100

[ MIDDLE ] y (LCB : 7, POS : 1/2) z (LCB : 7, POS : 1/2)

Applied Shear Force (Vu) 79.8843 kN 132.393 kN
Design Shear Strength (phiVc+phiVs)385.385 + 235.169 = 620.554 kN 387.771 + 251.414 = 639.186 kN
Shear Ratio 0.129 < 1.000 ....... O.K 0.207 < 1.000 ....... O.K
As-H_use 0.00157 m^2/m, 2-P10 @100 0.00157 m^2/m, 2-P10 @100

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:48
http://www.MidasUser.com
Gen 2021
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

1. General Information
Design Code Code Unit
AISC-LRFD10M N, mm

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
Base Plate Rib / Wing Anchor Bolt Concrete
A36 A36 A325 27,579KPa

3. Section
Column Base Plate Pedestal
HW 350x350x12/19 0.550x0.550x0.0320t (Rectangle) -

4. Rib Plate
Height Thickness No(X) No(Y)
0.400m 0.0120m 2EA 3EA

5. Anchor Bolt
No Type Length Position(X) Position(Y)
10EA M24 0.0280D 0.0500m 0.0500m

0.550
0.350
0.400

0.0100
0.0100
0.550
0.350

0.0100
0.0500

0.0500

6. Design Forces
Pu Mux Muy Vux Vuy
-793kN 183kN·m 3.700kN·m 4.400kN 62.00kN

7. Check bearing stress of base plate

2025-07-16 07:53 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

8.92

1.11 2.45 3.79 5.13 6.47 7.80

0.00 1.78 3.12 4.46 5.80 7.13 8.92

σmax σmin ø Fn σmax / øFn

8,952KPa 165KPa 0.650 46,884KPa 0.294

8. Check tension stress of anchor bolt

2025-07-16 07:53 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-61.47 -58.60

-128.64 -125.77

-195.81 -194.37 -192.94

-179.49 -146.86 -114.22 -81.59 -48.95 -16.32

-195.81 -163.17 -130.54 -97.90 -65.27 -32.63 0.00

Tu.max Tu.min ø Fnt Rnt Tu.max / øRnt

-196kN -58.60kN 0.750 620,528KPa 281kN 0.930

9. Check base plate

(1) Moment Diagram ( Element Force. Nodal Average is not Applied. )
Moment Diagram (Mxx)

2025-07-16 07:53 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

41.21kN·m/m

-9.03 -4.47 0.09 4.64 9.20 13.76

-50.95 -6.75 -2.19 2.36 6.92 11.48 84.15

Moment Diagram (Myy)

2025-07-16 07:53 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-49.86kN·m/m

-15.57 -10.32 -5.08 0.17 5.41 10.66

-61.13 -12.94 -7.70 -2.46 2.79 8.03 79.16

(2) Shear Force Diagram

Shear Force Diagram (Vxx)

2025-07-16 07:53 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-479.25 -286.72 -94.19 98.33 290.86 483.39

-5243.80 -382.99 -190.46 2.07 194.60 387.13 4937.06

Shear Force Diagram (Vyy)

2025-07-16 07:53 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-556.25 -309.87 -63.49 182.89 429.27 675.66

-5032.22 -433.06 -186.68 59.70 306.08 552.46 5339.31

(3) Design Moment (Use Average)

Mu ø Zbp Mn Mu / øMn
-49.86kN·m/m 0.900 0.000256 m3/m 63.54kN·m/m 0.872

10. Check rib plate

(1) Force Diagram
Moment Diagram

2025-07-16 07:53 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

2.37 5.48 8.60 11.71 14.82 17.94

0.81 3.93 7.04 10.15 13.27 16.38 19.49

Shear Force Diagram

2025-07-16 07:53 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

28.57 67.64 106.72 145.79 184.87 223.94

9.03 48.11 87.18 126.26 165.33 204.41 243.48

(2) Check Moment Capacity

Mu Mn.YIELD Mn.LTB øMn Mu / øMn
19.49kN·m 119kN·m 101kN·m 90.76kN·m 0.215

(3) Check Shear Capacity

Vu ø Vn Vu / øVn
243kN 0.900 715kN 0.378

11. Check anchor bolt (Cast-In-Place)

(1) Check Shear Strength
Vu1 ø Ab Fnv Rnv Vu1 / øRnv
6.216kN 0.750 0.000452m² 330,948KPa 150kN 0.0554

(2) Check Tensile Strength

Tu.max ø Fnt fv Fnt' Rnt Tu.max / øRnt
-196kN 0.750 620,528KPa 13,739KPa 620,528KPa 281kN 0.930

12. Check Development Length of Anchor Bolt (Hooked Bar)

ø Lanc Lh1 Lh2 Lreq Lreq / Lanc
0.750 0.672m 0.227m 0.408m 0.635m 0.945

2025-07-16 07:53 9
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

1. General Information
Design Code Code Unit
AISC-LRFD10M N, mm

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
Base Plate Rib / Wing Anchor Bolt Concrete
A36 A36 A325 20,684KPa

3. Section
Column Base Plate Pedestal
HM 594x302x14/23 0.800x0.850x0.0320t (Rectangle) -

4. Rib Plate
Height Thickness No(X) No(Y)
0.300m 0.0160m 1EA 3EA

5. Anchor Bolt
No Type Length Position(X) Position(Y)
12EA M24 0.0300D 0.0500m 0.0500m

0.800
0.302

0.0100
0.0100

0.300
0.850
0.594

0.0100
0.0500

0.0500

6. Design Forces
Pu Mux Muy Vux Vuy
-249kN 318kN·m 0.840kN·m -0.280kN -106kN

7. Check bearing stress of base plate

2025-07-16 14:07 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

6.55

0.82 1.80 2.78 3.77 4.75 5.73

0.00 1.31 2.29 3.28 4.26 5.24 6.55

σmax σmin ø Fn σmax / øFn

6,554KPa 1.064KPa 0.650 35,163KPa 0.287

8. Check tension stress of anchor bolt

2025-07-16 14:07 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-26.55 -26.31

-68.16 -67.92

-109.76 -109.68 -109.60 -109.52

-100.61 -82.32 -64.02 -45.73 -27.44 -9.15

-109.76 -91.46 -73.17 -54.88 -36.59 -18.29 0.00

Tu.max Tu.min ø Fnt Rnt Tu.max / øRnt

-110kN -26.31kN 0.750 620,528KPa 281kN 0.521

9. Check base plate

(1) Moment Diagram ( Element Force. Nodal Average is not Applied. )
Moment Diagram (Mxx)

2025-07-16 14:07 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-37.92kN·m/m

-12.52 -8.49 -4.45 -0.41 3.62 7.66

-54.25 -10.50 -6.47 -2.43 1.61 5.64 43.06

Moment Diagram (Myy)

2025-07-16 14:07 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-46.98kN·m/m

-28.45 -21.50 -14.55 -7.60 -0.65 6.29

-56.01 -24.98 -18.03 -11.08 -4.13 2.82 36.78

(2) Shear Force Diagram

Shear Force Diagram (Vxx)

2025-07-16 14:07 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-280.40 -167.27 -54.14 58.99 172.12 285.25

-2553.44 -223.84 -110.71 2.42 115.56 228.69 2423.09

Shear Force Diagram (Vyy)

2025-07-16 14:07 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-427.62 -258.15 -88.68 80.79 250.25 419.72

-1823.32 -342.88 -173.42 -3.95 165.52 334.99 2287.62

(3) Design Moment (Use Average)

Mu ø Zbp Mn Mu / øMn
-46.98kN·m/m 0.900 0.000256 m3/m 63.54kN·m/m 0.821

10. Check rib plate

(1) Force Diagram
Moment Diagram

2025-07-16 14:07 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

3.23 8.47 13.72 18.96 24.21 29.45

0.61 5.85 11.10 16.34 21.59 26.83 32.08

Shear Force Diagram

2025-07-16 14:07 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

10.00 47.60 85.20 122.80 160.40 198.00

-8.80 28.80 66.40 104.00 141.60 179.20 216.80

(2) Check Moment Capacity

Mu Mn.YIELD Mn.LTB øMn Mu / øMn
32.08kN·m 89.36kN·m 81.29kN·m 73.16kN·m 0.438

(3) Check Shear Capacity

Vu ø Vn Vu / øVn
217kN 0.900 715kN 0.337

11. Check anchor bolt (Cast-In-Place)

(1) Check Shear Strength
Vu1 ø Ab Fnv Rnv Vu1 / øRnv
8.833kN 0.750 0.000452m² 330,948KPa 150kN 0.0787

(2) Check Tensile Strength

Tu.max ø Fnt fv Fnt' Rnt Tu.max / øRnt
-110kN 0.750 620,528KPa 19,526KPa 620,528KPa 281kN 0.521

12. Check Development Length of Anchor Bolt (Hooked Bar)

ø Lanc Lh1 Lh2 Lreq Lreq / Lanc
0.750 0.720m 0.303m 0.408m 0.711m 0.987

2025-07-16 14:07 9
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

25.52 55.36 85.20 115.05 144.89 174.73

10.59 40.44 70.28 100.13 129.97 159.81 189.66

(2) Check Moment Capacity

Mu Mn.YIELD Mn.LTB øMn Mu / øMn
36.21kN·m 89.36kN·m 81.29kN·m 73.16kN·m 0.495

(3) Check Shear Capacity

Vu ø Vn Vu / øVn
190kN 0.900 715kN 0.295

11. Check anchor bolt (Cast-In-Place)

(1) Check Shear Strength
Vu1 ø Ab Fnv Rnv Vu1 / øRnv
10.60kN 0.750 0.000452m² 330,948KPa 150kN 0.0944

(2) Check Tensile Strength

Tu.max ø Fnt fv Fnt' Rnt Tu.max / øRnt
-136kN 0.750 620,528KPa 23,431KPa 620,528KPa 281kN 0.647

12. Check Development Length of Anchor Bolt (Hooked Bar)

ø Lanc Lh1 Lh2 Lreq Lreq / Lanc
0.750 0.720m 0.303m 0.408m 0.711m 0.987

2025-07-16 07:39 9
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

1. General Information
Design Code Code Unit
AISC-LRFD10M N, mm

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
Base Plate Rib / Wing Anchor Bolt Concrete
A36 A36 A325 20,684KPa

3. Section
Column Base Plate Pedestal
HN 912x302x18/34 0.900x1.100x0.0320t (Rectangle) -

4. Rib Plate
Height Thickness No(X) No(Y)
0.400m 0.0160m 2EA 5EA

5. Anchor Bolt
No Type Length Position(X) Position(Y)
18EA M24 0.0300D 0.0600m 0.0600m

0.900
0.302

0.0100
0.400
0.0100
1.100
0.912

0.01000
0.0600

0.0600

6. Design Forces
Pu Mux Muy Vux Vuy
-2,618kN -8.400kN·m 275kN·m 189kN -408kN

7. Check bearing stress of base plate

(1) Reaction Force not Exist.

8. Check tension stress of anchor bolt

2025-07-16 07:46 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

-201.17 -174.06 -146.96 -119.85 -92.75

-200.57 -92.15

-199.98 -91.56

-199.39 -90.97

-198.80 -90.38

-198.21 -171.10 -144.00 -116.89 -89.79

-184.40 -150.87 -117.35 -83.82 -50.29 -16.76

-201.17 -167.64 -134.11 -100.58 -67.06 -33.53 0.00

Tu.max Tu.min ø Fnt Rnt Tu.max / øRnt

-201kN -89.79kN 0.750 620,528KPa 281kN 0.955

9. Check base plate

(1) Moment Diagram ( Element Force. Nodal Average is not Applied. )
Moment Diagram (Mxx)

2025-07-16 07:46 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

26.40kN·m/m

-6.62 -2.24 2.14 6.52 10.89 15.27

-27.79 -4.43 -0.05 4.33 8.71 13.08 73.17

Moment Diagram (Myy)

2025-07-16 07:46 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

50.21kN·m/m

-15.89 -9.73 -3.57 2.59 8.75 14.91

-71.43 -12.81 -6.65 -0.49 5.67 11.83 82.44

(2) Shear Force Diagram

Shear Force Diagram (Vxx)

2025-07-16 07:46 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

-330.62 -196.49 -62.36 71.76 205.89 340.02

-2850.40 -263.56 -129.43 4.70 138.83 272.95 2578.71

Shear Force Diagram (Vyy)

2025-07-16 07:46 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

-524.53 -313.43 -102.34 108.76 319.86 530.95

-3629.32 -418.98 -207.88 3.21 214.31 425.40 3569.19

(3) Design Moment (Use Average)

Mu ø Zbp Mn Mu / øMn
50.21kN·m/m 0.900 0.000256 m3/m 63.54kN·m/m 0.878

10. Check rib plate

(1) Force Diagram
Moment Diagram

2025-07-16 07:46 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

9.27 23.48 37.70 51.92 66.13 80.35

2.16 16.37 30.59 44.81 59.03 73.24 87.46

Shear Force Diagram

2025-07-16 07:47 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2-A

45.27 109.66 174.05 238.44 302.84 367.23

13.07 77.46 141.86 206.25 270.64 335.03 399.42

(2) Check Moment Capacity

Mu Mn.YIELD Mn.LTB øMn Mu / øMn
87.46kN·m 159kN·m 136kN·m 123kN·m 0.713

(3) Check Shear Capacity

Vu ø Vn Vu / øVn
399kN 0.900 953kN 0.466

11. Check anchor bolt (Cast-In-Place)

(1) Check Shear Strength
Vu1 ø Ab Fnv Rnv Vu1 / øRnv
24.98kN 0.750 0.000452m² 330,948KPa 150kN 0.222

(2) Check Tensile Strength

Tu.max ø Fnt fv Fnt' Rnt Tu.max / øRnt
-201kN 0.750 620,528KPa 55,219KPa 620,528KPa 281kN 0.955

12. Check Development Length of Anchor Bolt (Hooked Bar)

ø Lanc Lh1 Lh2 Lreq Lreq / Lanc
0.750 0.720m 0.303m 0.408m 0.711m 0.987

2025-07-16 07:47 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
512kN 33.00kN·m 73.00kN·m

(2) Factored Load

Pu Mux Muy
599kN 51.00kN·m 120kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.100m

3. Foundation
Depth Cover Lx Ly fe
0.400m 0.0800m 5.000m 5.000m 80.34kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.550m 0.550m 0.000m 0.000m

2025-07-14 14:42 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1

5.00
2.50 2.50

2.50
5.00

Y1
2.50

X1
2.10
0.40

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 72.48 80.34 0.902
qu,max (kN/m²) 104 - -
qu,min (kN/m²) 87.17 - -
One Way Shear-X (kN) 152 884 0.172
One Way Shear-Y (kN) 140 839 0.167
Two Way Shear (kN) 581 1,219 0.477
Moment-X Direction(Muy, kN·m/m) 21.13 38.94 0.543
Moment-Y Direction(Mux, kN·m/m) 19.38 36.95 0.524
Rebar Space-Y Direction(sx, m) 0.200 0.457 0.437
Rebar Space-X Direction(sy, m) 0.200 0.457 0.437

2025-07-14 14:42 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Column 1
Service Load
Ps 656kN

Factored Load
Pu 814kN

(2) Column 2
Service Load
Ps 301kN

Factored Load
Pu 430kN

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 0.000kN/m³ 2.000m

3. Foundation
Depth Cover Lx Ly fe
0.500m 0.102m 7.250m 3.500m 80.34kN/m²

4. Column
No. Shape Section Lxi
1 Rectangle 0.550x0.550m 2.100m
2 Rectangle 0.550x0.550m 3.050m

2025-07-14 14:46 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

137.80

X
2025-07-14 14:46 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

5. Rebar
Position Top/Bottom Direction X Direction Y
Cantilever(L) Bottom #[email protected] -
Colm (1) Bottom #[email protected] #[email protected]
Span (1-2) Top #[email protected] -
Colm (2) Bottom #[email protected] #[email protected]
Cantilever(R) Bottom #[email protected] -

6. Check Soil Capacity

Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 66.76 80.34 0.831
qu,max (kN/m²) 68.12 - -
qu,min (kN/m²) 29.93 - -

7. Check Capacity
Check Items Calculated Criteria Ratio
One Way Shear-X (kN) 323 774 0.417
Two Way Shear (kN) 772 1,607 0.480
Moment-X Direction( Cantilever ) (kN·m/m) 32.95 37.29 0.884
Moment-X Direction( Column ) (kN·m/m) 35.48 47.14 0.753
Moment-X Direction( Span ) (kN·m/m) 0.000 0.000 0.000
Moment-X Direction(kN·m/m) 32.95 37.29 0.884
Moment-Y Direction(kN·m/m) 83.69 83.71 1.000

8. Check Rebar
Check Items Calculated Criteria Ratio
Rebar Space-X Direction(sy, m) 0.180 0.457 0.394
Rebar Space-Y Direction(sx, m) 0.100 0.457 0.219

2025-07-14 14:46 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Column 1
Service Load
Ps 296kN

Factored Load
Pu 368kN

(2) Column 2
Service Load
Ps 430kN

Factored Load
Pu 515kN

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.000m

3. Foundation
Depth Cover Lx Ly fe
0.500m 0.102m 8.400m 3.500m 80.34kN/m²

4. Column
No. Shape Section Lxi
1 Rectangle 0.550x0.550m 2.300m
2 Rectangle 0.550x0.550m 3.800m

2025-07-05 00:04 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

137.80

21.6

Y
X

2025-07-05 00:04 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

6. Check Soil Capacity

Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 78.27 80.34 0.974
qu,max (kN/m²) 36.84 - -
qu,min (kN/m²) 23.27 - -

7. Check Capacity
Check Items Calculated Criteria Ratio
One Way Shear-X (kN) 203 774 0.262
Two Way Shear (kN) 489 1,612 0.304
Moment-X Direction( Cantilever ) (kN·m/m) 22.34 31.79 0.703
Moment-X Direction( Column ) (kN·m/m) 23.49 31.79 0.739
Moment-X Direction( Span ) (kN·m/m) 0.000 0.000 0.000
Moment-X Direction(kN·m/m) 23.49 31.79 0.739
Moment-Y Direction(kN·m/m) 37.81 42.63 0.887

8. Check Rebar
Check Items Calculated Criteria Ratio
Rebar Space-X Direction(sy, m) 0.180 0.457 0.394
Rebar Space-Y Direction(sx, m) 0.150 0.457 0.328

2025-07-05 00:04 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
3,132kN 95.00kN·m 248kN·m

(2) Factored Load

Pu Mux Muy
3,527kN 129kN·m 350kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.600m

3. Foundation
Depth Cover Lx Ly fe
0.600m 0.0800m 3.400m 3.400m 427kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.850m 0.800m 0.000m 0.000m

2025-07-14 14:49 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2

3.40
1.70 1.70

1.70
3.40

Y1
1.70

X1
2.60
0.60

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 384 427 0.899
qu,max (kN/m²) 470 - -
qu,min (kN/m²) 323 - -
One Way Shear-X (kN) 740 986 0.750
One Way Shear-Y (kN) 721 956 0.754
Two Way Shear (kN) 2,982 3,103 0.961
Moment-X Direction(Muy, kN·m/m) 85.52 105 0.817
Moment-Y Direction(Mux, kN·m/m) 82.36 101 0.812
Rebar Space-Y Direction(sx, m) 0.120 0.457 0.262
Rebar Space-X Direction(sy, m) 0.120 0.457 0.262

2025-07-14 14:49 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2-A

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
3,789kN 51.00kN·m 426kN·m

(2) Factored Load

Pu Mux Muy
4,187kN 71.00kN·m 591kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.600m

3. Foundation
Depth Cover Lx Ly fe
0.600m 0.0800m 3.600m 3.600m 427kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.900m 1.100m 0.000m 0.000m

2025-07-15 21:27 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2-A

3.60
1.80 1.80

1.80
3.60

Y1
1.80

X1
2.60
0.60

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 414 427 0.970
qu,max (kN/m²) 499 - -
qu,min (kN/m²) 329 - -
One Way Shear-X (kN) 985 1,041 0.946
One Way Shear-Y (kN) 738 1,005 0.734
Two Way Shear (kN) 3,453 3,494 0.988
Moment-X Direction(Muy, kN·m/m) 106 118 0.896
Moment-Y Direction(Mux, kN·m/m) 78.60 81.32 0.967
Rebar Space-Y Direction(sx, m) 0.150 0.457 0.328
Rebar Space-X Direction(sy, m) 0.150 0.457 0.328

2025-07-15 21:27 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F3

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
1,677kN 154kN·m 192kN·m

(2) Factored Load

Pu Mux Muy
1,971kN 212kN·m 269kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.700m

3. Foundation
Depth Cover Lx Ly fe
0.500m 0.0800m 3.800m 3.800m 427kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.850m 0.800m 1.075m 0.000m

2025-07-14 14:52 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F3

3.80
2.98 0.82

1.90
3.80

Y1
1.90

X1
2.70
0.50

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 420 427 0.984
qu,max (kN/m²) 582 - -
qu,min (kN/m²) 0.000 - -
One Way Shear-X (kN) 168 887 0.189
One Way Shear-Y (kN) 681 853 0.799
Two Way Shear (kN) 1,709 1,925 0.887
Moment-X Direction(Muy, kN·m/m) 19.17 51.42 0.373
Moment-Y Direction(Mux, kN·m/m) 67.09 95.65 0.701
Rebar Space-Y Direction(sx, m) 0.100 0.457 0.219
Rebar Space-X Direction(sy, m) 0.200 0.457 0.437

2025-07-14 14:52 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F4

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
1,200kN 138kN·m 117kN·m

(2) Factored Load

Pu Mux Muy
1,439kN 192kN·m 165kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - 18.00kN/m³ 2.500m

3. Foundation
Depth Cover Lx Ly fe
0.700m 0.0800m 4.500m 4.500m 427kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.850m 0.800m 1.400m -1.400m

2025-07-15 21:15 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F4

4.50
3.65 0.85

3.65
4.50

Y1
0.85

X1
2.50
0.70

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] #[email protected] #[email protected] #[email protected]

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 363 427 0.851
qu,max (kN/m²) 524 - -
qu,min (kN/m²) 0.000 - -
One Way Shear-X (kN) 103 1,556 0.0661
One Way Shear-Y (kN) 1,475 1,499 0.984
Two Way Shear (kN) 1,228 2,169 0.566
Moment-X Direction(Muy, kN·m/m) 44.80 107 0.418
Moment-Y Direction(Mux, kN·m/m) 212 373 0.567
Rebar Space-Y Direction(sx, m) 0.0900 0.457 0.197
Rebar Space-X Direction(sy, m) 0.200 0.457 0.437

2025-07-15 21:15 2
LOWER GROUND PLAN

UPPER GROUND GRID A’-E, 10-12

UPPER GROUND GRID A’-E, 9-10

UPPER GROUND GRID A-B, 1-9

GRID A’-E , 11-12

GRID A’-E , 10-11

GRID A’-E , 9-10

2ND FLOOR GRID A-B, 7-9

2ND FLOOR GRID A-B, 2-7

2ND FLOOR GRID A-B, 1’-2

2nd FLOOR PLAN & CANOPY

3RD FLOOR GRID A’-E, 10-12

3RD FLOOR GRID A’-E, 9-10

3RD FLOOR GRID A-B, 4-9

3RD FLOOR GRID A-B, 1’-4

ROOF BEAM GRID A’-E, 9-12

ROOF BEAM GRID A-B, 1-9

ROOF FRAMING PLAN

COLUMNS

Eastgrove (Summary) Final 1 66
No ratings yet
Eastgrove (Summary) Final 1 66
66 pages
Eastgrove (Deiled11) Final
No ratings yet
Eastgrove (Deiled11) Final
248 pages
Structural Analysis AND Design For The Proposed Three (3) - Storey Commercial Building With Roofdeck
No ratings yet
Structural Analysis AND Design For The Proposed Three (3) - Storey Commercial Building With Roofdeck
155 pages
Structural Wind Load Analysis
No ratings yet
Structural Wind Load Analysis
89 pages
WLX Calc
No ratings yet
WLX Calc
2 pages
WX Specification
No ratings yet
WX Specification
5 pages
Midas Gen: Project Title
No ratings yet
Midas Gen: Project Title
3 pages
WIND
No ratings yet
WIND
3 pages
Wind Load Cal. Sheet
No ratings yet
Wind Load Cal. Sheet
3 pages
Wind Load Analysis for Engineers
No ratings yet
Wind Load Analysis for Engineers
3 pages
Viento
No ratings yet
Viento
4 pages
Engsolutions RCB: Wind Loads Nsr-10
No ratings yet
Engsolutions RCB: Wind Loads Nsr-10
4 pages
Wind Load Analysis for Project VIENTO
No ratings yet
Wind Load Analysis for Project VIENTO
4 pages
Analisis de Viento
No ratings yet
Analisis de Viento
4 pages
Viento Re
No ratings yet
Viento Re
4 pages
Wind Load On The Roof
No ratings yet
Wind Load On The Roof
14 pages
Structural Load Analysis Report
100% (2)
Structural Load Analysis Report
48 pages
MecaWind Tank Output
No ratings yet
MecaWind Tank Output
3 pages
Wind Load Analysis for Flat Roofs
No ratings yet
Wind Load Analysis for Flat Roofs
5 pages
WPFOutpu
No ratings yet
WPFOutpu
2 pages
Paseo Curtain Wall Strutural Calculation
100% (2)
Paseo Curtain Wall Strutural Calculation
79 pages
An Example Problem On Wind Load Calculation According To NSCP 2010
No ratings yet
An Example Problem On Wind Load Calculation According To NSCP 2010
32 pages
An Example Problem On Wind Load Calculation According To NSCP 2010
89% (9)
An Example Problem On Wind Load Calculation According To NSCP 2010
32 pages
Structural Calcs SHED
No ratings yet
Structural Calcs SHED
24 pages
Wind Load Analysis for Engineers
100% (1)
Wind Load Analysis for Engineers
6 pages
WindBBV1.0 Thinh
No ratings yet
WindBBV1.0 Thinh
2 pages
Wndload - Monoslope - ASCE 7-22
No ratings yet
Wndload - Monoslope - ASCE 7-22
5 pages
Structural Analysis: One-Storey Building
50% (2)
Structural Analysis: One-Storey Building
26 pages
Wind Loading in Accordance With ASCE7-10 Using The Directional Design Method
No ratings yet
Wind Loading in Accordance With ASCE7-10 Using The Directional Design Method
6 pages
WH04.Wind Loads
No ratings yet
WH04.Wind Loads
6 pages
Binder 1
No ratings yet
Binder 1
34 pages
NSCP 2010 Wind Load Calculation Example
No ratings yet
NSCP 2010 Wind Load Calculation Example
32 pages
WPFOutput2024 09 27 15 22 24 945
No ratings yet
WPFOutput2024 09 27 15 22 24 945
5 pages
Roof Structural Analysis PDF
No ratings yet
Roof Structural Analysis PDF
11 pages
Wind Load Parameters NSR-10
No ratings yet
Wind Load Parameters NSR-10
9 pages
Wind Loading (ASCE7)
No ratings yet
Wind Loading (ASCE7)
7 pages
Duopitch Roof Example
100% (1)
Duopitch Roof Example
6 pages
Wind Load Analysis per IS 875 Guidelines
75% (4)
Wind Load Analysis per IS 875 Guidelines
51 pages
Wind Loading ASCE 17-16
100% (5)
Wind Loading ASCE 17-16
18 pages
As-Nz 1170.2.2002 - Windload
100% (1)
As-Nz 1170.2.2002 - Windload
24 pages
Structural Analysis - 17 Storey Apartment Building PDF
No ratings yet
Structural Analysis - 17 Storey Apartment Building PDF
107 pages
Site Criteria and Loads On Structure
No ratings yet
Site Criteria and Loads On Structure
7 pages
Wind Load
No ratings yet
Wind Load
11 pages
V Class: Client: Date: Author: Job #: Project: Subject: Webinar Example 1 References
No ratings yet
V Class: Client: Date: Author: Job #: Project: Subject: Webinar Example 1 References
16 pages
Wind Load Calculation for Low-Rise Buildings
No ratings yet
Wind Load Calculation for Low-Rise Buildings
10 pages
Estimation of Wind Loads: CE 115 Structural Theory Ii
No ratings yet
Estimation of Wind Loads: CE 115 Structural Theory Ii
13 pages
Estimation of Wind Loads: CE 115 Structural Theory Ii
No ratings yet
Estimation of Wind Loads: CE 115 Structural Theory Ii
12 pages
Sachpazis - Wind Loading Analysis - Design For A Hipped Roof Example According To En1991 1 4 - Apr 2016
No ratings yet
Sachpazis - Wind Loading Analysis - Design For A Hipped Roof Example According To En1991 1 4 - Apr 2016
7 pages
Solved Examples Based On Draft IS875pt.3-1st Ed
100% (1)
Solved Examples Based On Draft IS875pt.3-1st Ed
85 pages
Wind Load Calculations Report
No ratings yet
Wind Load Calculations Report
5 pages
Solved Examples Based On Draft IS875pt.3-2nd Ed
No ratings yet
Solved Examples Based On Draft IS875pt.3-2nd Ed
94 pages
Wind Asce7 16 5 PDF Free
No ratings yet
Wind Asce7 16 5 PDF Free
18 pages
Wind Load Calculation IS:875 Software
100% (2)
Wind Load Calculation IS:875 Software
46 pages
Paseo Curtain Wall Strutural Calculation Ver. 2 March 18 2020 PDF
100% (1)
Paseo Curtain Wall Strutural Calculation Ver. 2 March 18 2020 PDF
93 pages
Bs1 Footing Sum
No ratings yet
Bs1 Footing Sum
2 pages
B1 Sum
No ratings yet
B1 Sum
1 page
Ground Floorplan Second Floorplan Second Floorplan: Scale: 1:250 MTS Scale: 1:250 MTS Scale: 1:250 MTS
No ratings yet
Ground Floorplan Second Floorplan Second Floorplan: Scale: 1:250 MTS Scale: 1:250 MTS Scale: 1:250 MTS
5 pages
Plans P2
No ratings yet
Plans P2
1 page
B1 Sum
No ratings yet
B1 Sum
1 page
Eastgrove Summary 07.22.25 2.4kpa-1-84
No ratings yet
Eastgrove Summary 07.22.25 2.4kpa-1-84
84 pages
Plans S1
No ratings yet
Plans S1
1 page
Actual Alignment
No ratings yet
Actual Alignment
1 page
Plans P3
No ratings yet
Plans P3
1 page
Angle
No ratings yet
Angle
1 page
Boundary Alignment
No ratings yet
Boundary Alignment
1 page
Refresher4A - MSTHC.v2
No ratings yet
Refresher4A - MSTHC.v2
11 pages
Plans S3
No ratings yet
Plans S3
1 page
Lunar Tix
No ratings yet
Lunar Tix
1 page
HW350X350
No ratings yet
HW350X350
9 pages
Green Engineering Principles
No ratings yet
Green Engineering Principles
13 pages
L1 Sum
No ratings yet
L1 Sum
1 page
Terrace
No ratings yet
Terrace
1 page
Midas Gen: Project Title
No ratings yet
Midas Gen: Project Title
8 pages
Office Floor Plan Layout
No ratings yet
Office Floor Plan Layout
1 page
New GRND
No ratings yet
New GRND
1 page
1
No ratings yet
1
1 page
AC Circuits Review Items
No ratings yet
AC Circuits Review Items
2 pages
Dams Need Specific Ancillary Structures and Facilities For Safe and Effective Operation
No ratings yet
Dams Need Specific Ancillary Structures and Facilities For Safe and Effective Operation
3 pages
Study
No ratings yet
Study
9 pages
Expansive Soil Stabilization Using Industrial Solid Wastes A Review
100% (1)
Expansive Soil Stabilization Using Industrial Solid Wastes A Review
11 pages
Untitled
No ratings yet
Untitled
2 pages
Timber Column Design and Investigation Guide
No ratings yet
Timber Column Design and Investigation Guide
8 pages
SEPCC Daily Activity Report
No ratings yet
SEPCC Daily Activity Report
2 pages
PVC Schedule 40 Fittings Specs
No ratings yet
PVC Schedule 40 Fittings Specs
2 pages
Commercial Construction Plan
No ratings yet
Commercial Construction Plan
32 pages
2020 MFD NFPA 13D Sprinkler Requirements
No ratings yet
2020 MFD NFPA 13D Sprinkler Requirements
2 pages
Building Materials: Doors & Windows
No ratings yet
Building Materials: Doors & Windows
66 pages
Civil Model Papers
No ratings yet
Civil Model Papers
24 pages
Flood Design of Substation Structures
100% (1)
Flood Design of Substation Structures
10 pages
Part A-Sheet-1 To 5-21CVL66
No ratings yet
Part A-Sheet-1 To 5-21CVL66
5 pages
MPRM April
No ratings yet
MPRM April
10 pages
Seismic Performance of Base Isolated and
No ratings yet
Seismic Performance of Base Isolated and
5 pages
Gravity Wall Design Optimization
No ratings yet
Gravity Wall Design Optimization
9 pages
Perbaikan Tanah
No ratings yet
Perbaikan Tanah
1 page
Nykka Booklet Digital
No ratings yet
Nykka Booklet Digital
24 pages
Statement of The The Problem FEU Tech Building - 3
No ratings yet
Statement of The The Problem FEU Tech Building - 3
3 pages
Well Control in Ubd
No ratings yet
Well Control in Ubd
6 pages
Microstructure and Tensile Properties of Steel Wire Drawing: March 2013
No ratings yet
Microstructure and Tensile Properties of Steel Wire Drawing: March 2013
14 pages
Unit 3 - Transportation Engineering - WWW - Rgpvnotes.in
No ratings yet
Unit 3 - Transportation Engineering - WWW - Rgpvnotes.in
20 pages
Load Carrying Capacity of Piles
100% (3)
Load Carrying Capacity of Piles
29 pages
Epoxy Coating of Steel Reinforcement
No ratings yet
Epoxy Coating of Steel Reinforcement
2 pages
SAPEM Chapter 12 Jan2013 PDF
100% (1)
SAPEM Chapter 12 Jan2013 PDF
177 pages
HDD Lesson and Learn
100% (1)
HDD Lesson and Learn
10 pages
Construction Data for Engineers
No ratings yet
Construction Data for Engineers
12 pages
Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
No ratings yet
Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
7 pages
Calculation of Crack Width and Crack Spacing: Ingemar - Lofgren@tcg - Nu
No ratings yet
Calculation of Crack Width and Crack Spacing: Ingemar - Lofgren@tcg - Nu
12 pages
Concrete Pier Reinforcement Design
No ratings yet
Concrete Pier Reinforcement Design
2 pages