~··

TECHNICAL MANUAL
FOR
COMPACT VHF RT2048

i~ )

S.P. RADIO A/S · AALBORG · DENMARK

',J
,~,1

:' I M~O.taGB
' '~
/
 RT2048

CONTENTS

1 INTRODUCTION
1.1 GENERAL DESCRIPTION 1-2
1.2 TECHNICAL DATA 1-3
1.3 CONTROLS 1-4
1.4 PRINCIPLE OF OPERATION AND BLOCK DIAGRAM 1-6

2 INSTALLATION
2.1 MOUNTING POSSIBILITIES 2-2
I
a 2.2
2.3
2.4
HANDSET
MICROTELEPHONE CONNECTOR
POWER SUPPLY
2-6
2-6
2-6
I 2.5
2.6
POWER CONNECTOR + EXT. LOUDSPEAKER
ANTENNAS
2-7
2-7
2.7 SPECIAL OPTIONS 2-7
2.8 REAR VIEW OF VHF RT2048 2-11
2.9 STANDARD FREQUENCY TABLE 2-12

3 SERVICE
3.1 MAINTENANCE
3.2 ALIGNMENT INSTRUCTIONS
3.3 PROPOSAL FOR NECESSARY MEASURING INSTRUMENTS
3.4 TEST PROBE
3.5 ADJUSTMENT PROCEDURE
3.6 TROUBLE SHOOTING
3.7 REPLACEMENT OF COMPONENTS
.3.8 REPLACEMENT OF MODULES
3.9 NECESSARY ADJUSTMENTS AFTER REPLAC~MENT OF MODULE
3.1 0 PIN CONFIGURATIONS

4 MODULE LOCATION
4.1 MECHANICAL DISASSEMBLING

5 CIRCUIT DESCRIPTION AND SCHEMATIC DIAGRAMS

5.1 KEYBOARD UNIT (MODULE 1)
5.2 INTERFACE UNIT (MODULE 2)
5.3 SYNTHESIZER UNIT (MODULE 3)
5.4 RX/TX UNIT (MODULE 4)
5.5 SELCALL UNIT (MODULE 5) OPTIONAL
5.6 INTERCONNECTION CABLE DIAGRAM

6 MICROTELEPHONE INSTALLATION
6.1 SPECIAL INSTALLATION WITH 2 MICROTELEPHONES
6.2 SPECIAL INSTALLATION WITH 3 MICROTELEPHONES
6.3 MECHANICAL DIMENSIONS FOR HANDSET

7 PARTS LIST

Appendix A • A TIS OPTION (OPTIONAL)

9403

I
i
 RT2048
CONTENTS

1 INTRODUCTION

1.1 GENERAL DESCRIPTION

1-2
1.2 TECHNICAL DATA
1-3
1.3 CONTROLS
1-4
1.4 PRINCIPLE OF OPERATION AND BLOCK DIAGRAM -1-6

9403
 RT2048

1 INTRODUCTION

The RT2048 VHF radiotelephone has been designed to comply with the increasing demands of a highly
technological product, which means high quality, small size, etc.

The RT2048 is furthermore designed to fit into the Compact 2000 module programme.

The RT2048 can either be installed and operated. as an independent unit, or in combination with other
elements of the Compact2000 programme. These include a Duplex VHF radiotelephone, a coasttelephone
station with a 400W PEP SSB transmitter and an SSB receiver with built-in FM and AM bands, and a
scrambler which ensures complete communication secrecy.

The VHF RT2048'has, by means of the latest technology in casting technique, been constructed to
withstand the most extreme conditions experienced in small, semi-open boats. The printed circuits inside
. are designed with a high degree of compactness and exceptional performance.

.a' I In the design of this VHF radiotelephone, S. P. Radio have taken into account all the circumstances it will
be exposed to in day-to-day operation. However, even a product of this high quality requires regular
servicing and maintenance, and we recommend a close observance of the directions contained in the
instruction book.

S. P. Radio is one of Europe's leading producers of maritime radio communication equipment- a position
which has been maintained by means of constant and extensive product development. We have a world-
wide network of dealers with general agencies in fifty countries. All our dealers are well-trained and able
to service all S.P. Radio products

9403 PAGE 1-1

r
1 INTRODUCTION RT2048

1.1 GENERAL DESCRIPTION

VHF RT2048 is an all solid state constructed microcomputer controlled VHF radiotelephone, intended for
ship/ship and ship/shore communication.

VHF RT2048 can operate in both simplex and semi-duplex mode.

VHF RT2048 includes all 55 international and U.S. VHF marine channels, and is as standard prepared for
up to 10 private channels, selected as simplex or semi-duplex channels in the frequency band 154.4-
163.75 MHz.

VHF RT2048 is equipped with flexible scanning facilities or additional30 private channels in the above
mentioned frequency band.

VHF RT2048 has built-in dual watch facility, which enables the operator to listen out on two channels
simultaneously (the selected channel and a programmable preference channel- normally channel16).

VHF RT2048 is provided with a quick select channel, normally channel 16.

VHF RT2048 is provided with continuous turn-style operation of SQ and AF level for optimum resolution.

VHF RT2048 is provided with a push-button keyboard offering an attractive tactile feeling and a safe finger- ~ l
guide in the metal front. Besides, the keyboard is fitted with night-illumination of the lettering from behind. ,! '
L'
VHF RT2048 has a high efficient LED read-out of channel number and other indications for optimum reading
under all conditions.

VHF RT2048 is a modern transceiver with an all synthesized frequency generation based on a single
crystal.

VHF RT2048 has a built-in 12W AF power amplifier, which delivers 6W into the large built-in loudspeaker.

VHF RT2048 is for 12V DC supply. Voltage change-over from 24V to 12V is easily done by the power supply
N420.
,_
VHF RT2048 has an extremely low standby current consumption, typically below 100 mA.

VHF RT2048 is housed in a corrosion resistant metal cabinet with a green nylon finish.

VHF RT2048 can be delivered with a built-in selcall decoder, which will decode a selective call CA or all
ships call CQ

rt
~
I
I

J~i
"rf~ ~~
I

' .
9403
PAGE 1-2

~
J 1 INTRODUCTION RT2048

) 1.2 TECHNICAL OATA

J4 Fulfils the international CEPT regulations.

GENERAL

J All international maritime VHF channels

Private channels:
Operation:
10, may be extended to 40
Simplex and semi-duplex

J '
Modulation:
Antenna impedance:
Frequency stability:
Temperature range:
G3EJN (Phase)
50 ohm
+1- 10 ppm (Spec. vers. +1- 5 ppm)
-20°C to +55°C
Nominal power supply: 13.2V DC
Power supply variation: 12V DC -1 0% to +30%
(with data according to international standards)
Power consumption: Standby == 0.1 A
Transmit = 5 A
Dimensions: Height: 98 mm
Width: 225 mm
Depth: 160 mm
Weight: 3.1 kg

RECEIVER
Frequency range simplex: 154.40-159.15 MHz
Frequency semi-duplex: 159.00- 163.75 MHz
Sensitivity: 0.25 uV PO at 12 dB SINAD
AF output power: 6 Watt/4 ohm
Telephone output: 0.5V RMS/200 ohm
Distortion: Less than 5%
Scanning facilities: Flexible scanning programme,
with possibility for all international
channels and 10 private channels.
Accessory: Selcall decoder according to ,.
CCIR

TRANSMITTER
Frequency range normal: 154.40-159.15 MHz
Frequency range special: 159.00-163.75 MHz
RF output power: 25 Watt +0 to -0.5 dB
Reduced RF output: 0.5 to 1 Watt
Distortion: Less than 5%

I '

9403 PAGE 1-3

i
1 INTRODUCTION RT2048

1.3 CONTROLS
I~~I~~

29656

Indication of ON/OFF/VOL turn-style knob operation.

Squelch sensitivity control knob with turn-style operation.

~~~ Quick selection of the call and distress channel16.

Digits from 1 to 0 'I .,

Activates the functions marked in orange on the keyboard.

Whenever the keyboard is in "shift-mode" it will be
indicated by "cornerbars" in the display

Ill Selects scanning programme.

Adds a channel to the scanning table.

Deletes a channel from the scanning table.

PAGE 1-4 9403

J 1 INTRODUCTION RT2048

J Selects the scan time from 1 to 99 seconds.

The time chosen is the listening time on one of the secondary channels receiving
a signal.
J
J Selects the dual watch facility.

l Selects 1W reduced power output.

"
. Selects the VHF channels used in the USA.

I
..,

1111 The intensity of the LED-indicators can be controlled in four steps.

The keyboard illumination is switched on and off.

II Tests the selcall decoder and resets the selcall decoder after a call.

II Selects the standard private channels.

READ-OUT
Channel Read-Out All international maritime channels are shown by the twotdigits,
when the channel has been keyed ln.
Selection of a standard private channel will be indicated with a P-.

Reduced Power Transmitting US-Channels

In harbour areas or In the close Whenever the handset switch In the USA a number of the
vicinity of anothervessel, is depressed, and the transmitter international duplex channels
transmissions should be with output power level has reached are used as simplex channels.
reduced power. an appropriate level, the "TX" Ships sailing in American waters
When the display shows 1W, will appear. must therefore be able to select
the transmitter output power is these channels as simplex channels.
reduced from 25W to 1W The appearance of "US" on the
Where two stations are close display indicates that this mode of
together, this reduction can operation is in use.
improve communication quality.

, !"'
.
9403
29655

PAGE 1-5
 1 INTRODUCTION RT2048

1.4 PRINCIPLE OF OPERATION

FREQUENCY GENERATION
All the internal frequencies are referenced to a crystal oscillator, running on 14.85 MHz.
The 14.85 MHz is divided by 4 in the REFERENCE DIVIDER, to generate a 3. 7125 MHz signal, which is
the input to the PLL-reference divider and clock-signal for the microcomputer.
The local oscillator signal for the first mixer in the receiver and the transmit signal are generated in a phase-
locked loop (PLL). To generate the needed frequencies, which are specified as follows:

139.1 MHZ :::; fl01 :::; 148.45 MHz; 154.5 MHz:::; fTX NORMAL:::; 159.15 MHz

159.0 MHz:::; fTX SPECIAL<< 163.75 MHz

a bandshift is performed in the VCO.

The loop reference frequency- and so the resolution- is 12.5 kHz, derived by dividing the reference divider
output with 297. ·
The VCO output frequency is divided down to 12.5 kHz after the dual-modulus principle with a
PRESCALER dividing with 32/33.
The phase detector output controls the CHARGE PUMPE feeding the loop filter integrator.
· If there is a difference in phase/frequency between the inputs to the phase detector. An error current from
the charge pumpe will be integrated in the loop filter, producing the needed voltage for the VCO.

RECEIVER
The antenna signal is fed to the RX AMPLIFIER through the RX/TX relay.
The bandpass filters around the RX amplifier are tuned by means of capacitor diodes, which are controlled
by a DC-voltage derived from the VCO control voltage in the PLL.
The received signal is converted to the first intermediate frequency on 15.3 MHz in the FIRST MIXER,
using the VCO signal from the RX BUFFER AMPLIFIER as local oscillator signal.
The signal is filtered and amplified before down-conversion to 450kHz in the SECOND MIXER. The crystal
oscillator signal is used as local oscillator signal.
After filtering in the SECOND IF FILTER, the signal is amplified and detected.
The AF signal is passed through a mute switch before undergoing appropriate amplification and filtering
to get the right frequency response.
Besides, the detected output is filtered in the SQUELCH FILTER before it is amplified, detected, and
compared with a reference level to get a logical level for the microcomputer, which controls themute circuit.
The telephone amplifier and the AF power amplifier produce the wanted output levels forthe earpiece and
the loudspeaker.

TRANSMITTER
The signal from the microphone is passed through a PRE-EMPHASIS network before appropriate
amplification and compression in the AF AMPLIFIER COMPRESSOR.
This signal is filtered before it is fed to the VCO, where the modulation of the transmitter signal takes place.
As the VCO oscillates direct on the transmitting frequency in TX-mode, the signal only has to be amplified.
This is done in the TX BUFFER AMPLIFIER and the TX POWER AMPLIFIER.
The power supply for the TX power amplifier is regulated by a feed-back loop via the POWER SENSE
circuit to maintain constant output power level. Switching between full and reduced output power level is
made by means of the PA-REGULATOR.
To reduce the level of harmonic components in the output signal it is passed through a HARMONIC
FILTER before it is led to the antenna via the RX-TX-RELAY.

MICROCOMPUTER
The microcomputer on the interface unit is taking care of various functions, among these the user interface,
which means reading of the keyboard and readout to the LED-display via the DISPLAY-LATCHES.
Moreover the computer calculates the appropriate division figures for the PLL, controls the transmitter
power level, the AF mute circuits, and reads and writes to the EEPROM'S.
When a selcall unit is installed, the microcomputer also controls the selcall switch capacitor filter.
The serial interface is only for factory production use

PAGE 1-6 9403

 1 INTRODUCTION RT2048

BLOCK DIAGRAM

!l.r/T~ v11i! 14)

L
-----,
Wst=l 0-1

~ ::
'------jtAtiL mf<rf4«tli>-J

r~~o_:~r3
3,7125 MHz

··ii:
Synthesizer unit(3) I
L----------------- _ _ _ _ _ _ _ J
BLOCK DIAGRAM RT 2048

PAGE 1-7
J
,J CONTENTS
RT2048

J 2 INSTALLATION

J 2.1

2.2
MOUNTING POSSIBILITIES

HANDSET
2-2

2-6
J <

2.3 MICROTELEPHONE CONNECTOR 2-6

11~~q 2.4 POWER SUPPLY 2-6

"'~'
2.5 POWER CONNECTOR + EXT. LOUDSPEAKER 2-7
J 2.6 ANTENNAS 2-7
~~t 2.7

,
(>'}::,

~~·
SPECIAL OPTIONS 2-7
'"'-
2.8 REAR VIEW OF VHF RT2048 2-11
i~{
k\:
L&{ 2.9 STANDARD FREQUENCY TABLE 2-12

"' J

9403
,J
RT2048

J 2 INSTALLATION

J Before installation of a SAILOR VHF RT2048 the following points must be observed:

•J 1. Which facilities have to be enabled?

Selcall, private channels, US-mode, dual watch, scanning facilities, etc. The procedure how to
enable the facilities is described in the manual: INSTRUCTIONS FOR IDENTITY AND SERVICE
PROGRAMMING OF SAILOR VHF RT2048.

J,, 2.
This manual will only be delivered to dealers and general agents, where it must be at the disposal
of trained service people in the service workshop.

In what way the VHF RT2048 has to be installed?

In the section MOUNTING POSSIBILITIES, the installation of VHF RT2048 is described either as

•J
"'~
3.
an independent unit or in cpmbination with the other elements of the Compact 2000 programme .

Handset.
Installation of handset, see the section HANDSET.

4. Externalloudspeaker.
An external loudspeaker 4-8 ohm/6W can be connected to the power connector J 1, pin 1 and 6, see
the section POWER CONNECTOR+ EXT. LOUDSPEAKER.

5. Special options:
Remote alarm for selcall, AF to information decoder, AUX I and AUX II information, etc. are available,
see the section SPECIAL OPTIONS

'
I
.
.
.

9346 PAGE2-1

I
21NSTALLATION RT2048

2.1 MOUNTING POSSIBILITIES

The VHF RT2048 cabinet is designed in a module called a mini 1/4 box. For this module we can supply a
wide variety of installation brackets etc. which will be described below. We have made a drawing including
dimensions and drilling plan for each type and we kindly ask you to look at the drawing ·for the type in
question.

H2077 MULTI·PURPOSE MOUNTING BRACKET

This mounting bracket is as standard deliveredtogetherwith RT2048.1t permits a wide variety of installation
possibilities such as tabletop, bulkhead or deckhead. It is easy to remove the set by unscrewing the two
buttons of H2077.

H2on

(£j
ca!MDDDij)
. ~ODD

~
.o oooo
ooq !;

(·

"'" bl
Jl m

25572 25571

r
f1nnnnf1nnnn
nnn•"'""' 11 1 1111t 1 1nnn
1111111 II 1111 11111111 11111111111
r J u u u u u i1 u u u u u u u u u L 1

I .T
I

rj-Jr-f,oc.,.. 11Smm ·-·-·-·-·-r..-~-,

'
I

I
-'.
~

f--r

L\+·-·-· 200~m ·--·--tfo_·J --i---'-

Weight:
Mounting kit H2077:
VHF RT2048:
0.4kg
1
I 3.2kg
\ ~
I I
L------------------~

25668

PAGE2-2 934!>
 2INSTALLATION RT2048

H2067 MOUNTING BRACKET FOR TABLETOP, BULKEHAD OR DECKHEAD MOUNTING FOR MINI
1/4 BOX
This mounting bracket is used when RT2048 is to be mounted next to other SAILOR units in the Compact
2000 programme mounted in H2055 mounting brackets. For example when installing the RT2048 next to
the scrambler CRY2001 it is possible to tilt both units in the same angle.

H2067

0
0
0
0
0

•J 0

JJ

25574 25573

0 0

25575

----l
I
I
I
~
I
I

!i
. I nnnnnnnnnro
Weight:
Mounting kit H2067: 0.5kg
I nnnt 1 1 1 111tiii 1 " 111111 M,.,fi VHF RT2048: 3.2 kg
II ! :J I 11111\llllllllllfllllll\llltll I
u lJ u lJ u u u u lJ u lJ u u l1 u Li

+' :(~·-·--·-·------A~.
T 4,Pes. •f.5mm T :
------ =+·7
II
1t- tl.£11=
~~~
175mm

', I ~
____ j I l ___________________ j I
\ ""

25659A

9346
PAGE2-3

!
2 INSTALLATION RT2048

H2057 ANGLE HINGES FOR TABLETOP, BULKHEAD OR DECKHEAD MOUNTING FOR MIN11/4
BOX

H2057 is designed for stationary installation. It offers a lot of mounting possibilities using the different holes
in the angle hinges when tilting the VHF.

H2057

ca ODD$
ODD fi

.0
oooo
ODD$
·~

riJ

rnln:N•
rrlnT. .. 118
251

25534 25530
71

0
0
0
0
0
0
0
0
Lt
t.
0 0 0 0
0 0 0 0

71

25531A 25531
nnnnnnnnnn
nnnllllllltltllllllftllnnn
1 1 tt111 1l t l t l l l t l l l 1 I II I l t t l l t • l

fflfJ~U~·~· ~·~-~-~-~1*]~
. II ~I · I
-
c 0 00~o o o
l::;:=n-,
,: i'"il
I I
2.38mm
.
ltl:
~'n· ,
I I
"l'
1· tl 11 1
Lt\·-·-·-·-·-·-·-·itJ=·
~00

~00
8; i8 I I
r
[
.r
f ·~ I I
0 OoiW5Q o o I I
I I
}--W ~--------------------~
.
25669

min f/1/o
rm.tl&•
n n n n n nn nn n
nnnllltlltll'''''''l'''nnn
l t l l l t I llt·l l l l t l l t l t l t . l t l l t l l l l l
..r.J iJ L1 U t1 U 1.J U tJ U U U IJ U U U L':l

lu~~pa&."'6m;,-·-·-·-·-[if·i
II ·
I I · 11
25533
''I'
u.'
11 . I
206mm 'I''
k
1 . If "'
,, 0\

~·-·----·-·--·--·-L.f,.::l'-::_·_ __._
Dimensions when using a right-angled VHF plug.
Dimensions when using a standard VHF plug.
I
~
I
\. _ ____ ------------- ---..J
I
I
J
r
If!
Weight: Mounting kit H2057: 0.4 kg ·p
VHFRT2048: 3.2kg 25670 ~
PAGE2-4 9346

tl
I
 J
IJ 2 INSTALLATION

H2063 CONSOLE MOUNTING KIT FOR 1/4 BOX

RT2048

This mounting kit is used for console flush mounting of 1/4 box and mini 1/4 box.
Free distance must be kept to allow free air circulation, ambient temperature max. 40°C.
-J
.J H2063

J
0

25663

Weight:
Mounting kit H2063: 1.0 kg
VHF RT2048: 3.2 kg

24703

~pes. tl3 • JO

Bpcs. M5 •8

I '

9346
25657 lJ pes. M5•30

PAGE2-5

I
i
21NSTALLATION RT2048

2.2 HANDSET

The handset can be placed anywhere near the VHF set The cable is five-cored and connected to the rear
of the VHF through a 9-pole Sub-D connector. i '
Installation of the cable, see the drawings of the mounting b~ckets. The cable grommet must be placed 12V OPERATION
in the most convenient groove in the mounting brp.cket ;
I
If more than one handset is needed, please seethe sectior1 SPECIAL INSTALLATION ·wiTH 2 OR 3 +REO 2.5mm~
MICROTELEPHONES. I i -IJLACJ( 2.5mm~~-.d=t'='\---r.J;]
for connect ion
I . 011/0f'F 8/.UE 0.5mrrr
(NoT tiSElJ kiH~N 12V
external supply (12
1· 8A7T£RY SUPPLY)
l !'!It
2.3 MICROTELEPHONE CONNECTOr
BlOC/{ .lJIAGRAH OF Sil'APP/H6 FtJR 12V OC
II
Pin No. 1 Telephone
PinNo.2GND
PinNo.3GND
PinNo.4Mic
PinNo.5Key
Pin No. 6 Spare
Pin No. 7 Distress CRY*
Pin No. 8 "Serial input"
25666 Pin No. 9 +13V internal I 25654
PU~ '
• ooly"""" whoo optioo """" pro • 0~.
' 2411 OPERATION
2.4 POWER SUPPLY
The standard power supply for RT2048 is 12V Dq. For 24V o;c supply an external power supply N420 (a
24V DC to 13.2V DC serial regulator)·can be used. I
For 11 OV AC, 127V AC, 220V AC, or 237V AC op~ration an ~xtemal power supply N163S must be used 1'1/C.
together with N420. ! ,
+
I i2~V lJC _
Strap for connectior
I to N420 l24V l

'
BlOCK IJIAGRAH OF Si.l!APPIYG FIJR 24 V IJC

I
l25665
l

f'AQ.E2
 '

J
',./

2 INSTALLATION RT2048

J 2.5 POWER CONNECTOR+ EXT. LOUDSPEAKER

J '
VIEW FROM MOUNTING SIDE

:J Pin
Pin
No. 1 Ext. loudspeaker
No. 2 Ext. mute*
Pin No. 3 +12V power supply
Pin No.4 on/off for 24V supply
Pin No. 5 -12V power supply
Pin No. 6 Ext. loudspeaker
Jf}l
24914

'j * only active when option board pcb is installed.

If necessary a 4-8 ohm/6W external loudspeaker can be connected to pin No. 1 and pin No. 6 in the power
connector J 01 (observe that there is DC voltage on both wires).

External loudspeakers SAILOR H2054 and H2074 are available.

2.6 ANTENNAS

All common 50 ohm antennas, which cover the used frequency range with a reasonable standing wave
ratio, maximum i .5, are available.
The antenna is connected to the set by means of a 50 ohm coaxial cable with low loss, e.g. RG213U. At
the cable end a PL259 plug is mounted.
The antenna must be placed as high and clear as possible. The horizontal distance to metal parts must be
at least one metre.
S. P. Radio has an antenna of the necessary specifications available. The mentioned antenna is
characterized by small external dimensions. For further particulars see special brochure VHF AERIALS .

.... I

2.7 SPECIAL OPTIONS

With a small modification in RT2048 the following options are available:

1. K-switch function (used on river boats in Germany). Can be enabled by means

of the identity programming. US-button is changed to K-switch.

2. With DISTRESS OPTION installed

S.P. No. 625661
a. Distress output to CRY2001/2002.

3. With SELCALL OPTION installed

S.P. No. 625660
a. SELCALL RELAY, when the selcall has accepted a CQ or an individual call signal, the selcall
relay will turn on and short circuit two wires, which can be used for remote alarm.
Max. contact load: i OOV AC/24 V DC - 2A.
b. AF TO INFORMATION DECODER, the circuit giving AF signals to the information decoder
is turned on when the set has accepted a CQ or an individual call signal. The circuit is turned
on/off by the microprocessor.

I 9346 PAGE2-7

I
i
2 INSTALLATION RT2048

4. With AUX INTERFACE OPTION installed

S.P. No. 625473 ·~
(AUX1, AUX2 and MUTE functions) (Distress and Selcall functions are also mounted).
a. AUX2, when information on certain channels is wanted, i.e. controlling a watch keeping
receiver, the AUX2 information can be used, a relay is controlled from the microprocessor.
L ('
Max. contact load: 1OOV AC/24V DC- 2A.
b. AUX1, when function code in Prom 1 is enabled, AUX1 is free programmable on all
international channels ("0" or "1").
L:
Standard programming on international channels is "0".
Max. contact load: 1OOV AC/24V DC-2A.
~<
t"'Z·
c. MUTE, makes it possible to mute AF power amplifier from external equipment. ~~
Activated by a make function between pin 5 and pin 8 in P1 on option board.

5. With BUS INTERRUPT OPTION installed

S.P. No. 626945
This module is used for interface to VHF DSC RM2042.
L.
6. With ATIS OPTION installed ,.
S.P. No. 728665
The module 628652 is used for interface to ATIS module 626707, which is mounted on this PCB.
t
For circuit description and programming of ATIS option please refer to Appendix A- ATIS OPTION

~25~73
Lju,r IIVTERf/ICE oPi7oAI
(module 6}
625660
SELCAll tJPTIIJN f·

(module!.)
625661
DISTRESS OPTION
(mQr/vle 6)
62694'5 '
25662A 8US IN[ERROPTOPTtdAI
(modvle6)
628652
fiT/S BfiSE PC8
(module 6)
COMPONENT LOCATION FOR SPECIAL OPTIONS MODULES
VALID FOR 625661/625660/625473

Seen from component side Seen from component side

with upper side tracks. with lower side tracks.
PCB rev. 25473

PAGE2-8 9346
 21NSTALLATION RT2048

COMPONENT LOCATION FOR 626945

J
:J 0 0 0 Ill @ liP!® @ 0 0 0 (I)
3J 1A3TH aua

J Seen from soldering side

with soldering side tracks.
PCB rev. 26945
Seen from soldering side
with component side tracks.

~'
FJ)
DIAGRAMMES FOR SPECIAL OPTIONS

··.
625660

.3
SELCALL OPTION (6)
~ I
I

I ALARM
2 All% I
3 AIIXJT
<9 TEUPMJN'E
5 6}.1/J
6 0/STRliSS
7 + I.JII I AlT.
8 EXT. }lt!TE L.S. ~ ALARft (}/JT
9 17/C. IN
10 /1/C. Ot!T
II KEY I Af" ra l#f"OR/1
12 !1t!TE At:·AI?P. JJECO/J€R

.........................................................._ _ _ _ _ _ 5·0·25473 --'fll!llll/f

f·

625661

DISTRESS OPTION (6)

I ALARM
2 AI/X I
3 AIJX ff
~ TEUP/101/E
5 6N'lJ
6 D!S!J?ESS
7 + I.JV !N'T.
/J EXT. i?t!TE /.$
9 !11&. /#
/Q !1/C, PIJT
If k'EY
12 1?/JTE AF·AI1P

........_ _ _ _ _ _ _ _ _ _ _ _ 5-0·25~73~--'fll!llll/f

9346
PAGE2-9

I
2 INSTALLATION RT2048
L;('
625473 !
.!Mil

3
AU% INTERfACE OPTION (6) ~;(lAR/10/JT
.f/JY I
I

~·
I AIAR/1
L.•
2AUX I
3 AUK Jl
4 TELEPI/tWE
SGIIO
(
L
6 OISTRCSS
7 •13V lilT.
8 EJT. /11/TE lS.
~-
9 /11C IN
I~ I11C 01/T
II KEY
12 /'!liTE 4F -AI1P

'-...,.....,,...,..,.....,,.....,........,....,....,.........,....,,..,_.,........,.....,...,.....,......,..,.s-o-25¥73 __..,

626945

Bus Interrupt Option (6)

PIN I ALARM
PIN 2 AUX I
PIN 3 AUX II
PIN 4 TELEPHONE
PIN S GND
PIN 6 DISTRESS
PIN 7 +13V INT.
PIN 9 EXT. MUTE LS.
PIN 9 NIC. IN
PIN 10 NIC. OUT
PIN II KEY
PIN 12 MUTE AI'-AHP. PI

~- .....................................- 4-B-26945 ..............................,

PAGE2-10 9346

r
 2 INSTALLATION RT2048

DELA YEO KEY OPTION

To make a repeater station on a duplex channel, you need two pes. of RT2048, one for receiving on Lo
band, one for transmitting on Hi band. To get this function, the function code has to be reprogrammed for
the specified channel in both sets. The modulation signal is taken on the earpiece from the receiver unit
and led to the microphone input of the transmitter unit. No attenuation required. The key for the transmitter
unit is taken from the special option board, Delay Key Option, to get the transmitter unit keyed approx. 10
seconds after last received signal.

Seen from component side with upper side tracks.

626622

DELAYED KEY OPTION (6)

P01
1 ALARM
2 AUXI
3 AUXII
4 TELEPHONE
5 GND
6 DISTRESS
7 +13V INT. 7&-t----+------l
8 EXT. MUTE LS. B <>+-+------J~---------,
9 MIC.IN 9
10 MIC.OUT 1
11 KEY 11
12 MUTE AF-AMP 12&-t-----+----H

.§
0

DELA YEO KEY OPTION MODULE (6) RT2048 ECI A/S 5·0-26622/2-0-25473A 626622

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

C1-6 CAPACITOR ELECTROLYTIC 1OuF 20% 25VDC ELNA R8L-25-V -100-M-V2Z-T58 14.661
C2-6 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK Y8 471 K 16.095
C3-6 CAPACITOR CERAMIC 1nF 10% 50VDC CL2 KCK RT-SK-HE50 SJY8 102 K 1f).160
C4-6 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 78104 11.136
J1-6 PLUG 1110" SIL 12 POLES EURO DIP SL 12 0 Z 78.328
R1-6 RESISTOR MF 470 OHM 5% 0.33W PHILIPS 2322187 7347 02.464
R2-6 RESISTOR MF 150k OHM 5% 0.33W PHILIPS 2322187 73154 02.524
R3-6 RESISTOR MF 1M OHM 5% 0.33W PHILIPS 2322187 73105 02.544
T1-6 TRANSISTOR AF 8C548 NPN T0-92 PHILIPS 8C548 (-N-8/-C) 28.070
T2-6 TRANSISTOR AF 8C548 NPN T0-92 PHILIPS 8C548 (-N-8/-C) 28.070

9520
PAGE 2-10a

I
!
 2 INSTALLATION RT2048

2.8 REAR VIEW OF VHF RT2048

Power connector for 12V or N420 Antenna connector

~}
~~
('1
' ···~

'.J Thread for cover

Thread for cover
allen screw allen screw

Fuse cover with

spare-fuse

Microphone
connector

25567

.....

9350 PAGE 2-11

~~
I!
21NSTALLATION RT2048
I I

2.9 STANDARD FREQUENCY TABLE ~

"
(,

TRANSMITTING RECEIVING FREQUENCY (MHz) l

CHANNEL FREQUENCY US MODE INT'L MODE
~
(MHz) (A.-CHANNELS)
I (INT.-CHANNELS)
(

01 156.050 156.050 160,650

02 156.100 160.700
03 156.150 160.750
04 156.200 160,800
05 156.250 156.250 160.850
06 156.300 156.300
07 156.350 156.350 160.950
08 156.400 156.400
09 156.450 156.450
10 156.500 156.500
11 156.550 156.550
12 156.600 156.600
13 156.650 156.650
14 156.700 156.700
15 156.750 156.750
16 156.800 156.800
17 156.850 156.850
18 156.900 156.900 161.500
19 156.950 156.950 161.550
20
21
157.000
157.050 157.050
161.600
161.650
L
22 157.100 157.100 161.700
23
24
157.150
157.200
157.150
161.800
161.750
L
25 157.250 161.850
26 157.300 161.900
27 157.350 161.950
28 157.400 162.000
60 156.025 160.625
61 156.075 160.675
62 156.125 160.725
63 156.175 156.175 160.775
64 156.225 160.825
65 156.275 156.275 160.875
66 156.325 156.325 160.925
67 156.375 156.375
68 156.425 156.425
69 156.475 156.475
70 156.525 156.525
71
72
73
156.575
156.625
156.675
156.575
156.625
156.675
r
I
74 156.725 156.725
77 156.875 156.875
78 156.925 156.925 161.525
79 156.975 156.975 161.575
80 157.025 157.025 161.625
81 157.075 157.075 161.675
82 157.125 157.125 161.725
83 157.175 157.175 161.775
84 157.225 161.825
85 157.275 161.875
86 157.325 161.925
87 157.375 161.975
88 157.425 157.425 162.025
WX1 Inhibit 162.550
WX2 Inhibit 162.400
WX3 Inhibit 162.475
WX4 Inhibit 161.650
PAGE 2-12 9350
.J
CONTENTS

J 3. SERVICE

J 3.1. MAINTENANCE
3.2. ALIGNMENT INSTRUCTIONS
J 3.3. PROPOSAL FOR NECESSARY MEASURING INSTRUMENTS

J 3.4.
3.5.
TEST PROBE
ADJUSTMENT PROCEDURE
I 3.5.1 ADJUSTMENT OF SYNTHESIZER UNIT
. "~~
3.5.2. ADJUSTMENT OF RX!TX UNIT
·J 3.6. TROUBLE SHOOTING
3.7. REPLACEMENT OF COMPONENTS
3.8. REPLACEMENT OF MODULES
3.9. NECESSARY ADJUSTMENTS AFTER REPLACEMENT OF MODULE
3.9.1. REPLACEMENT OF RXfrX UNIT
3.9.2. REPLACEMENT OF SYNTHESIZER UNIT
3.1 0. PIN CONFIGURATIONS

"'.f''.'·i~· ·.
~(j

II
 J 3. SERVICE
)
3.1. MAINTENANCE
J
~

J PREVENTIVE MAINTANANCE
If SAILOR RT2048 has been installed in a proper way the maintenance can be
reduced to an overhaul at each visit of the service staff.

J ~
Then inspect the set, the antenna, cables, and plugs for mechanical damages,
salt deposits, corrosion, and any foreign material.
Owing to its traditional structure, the SAILOR RT2048 has a long lifetime,
but it must always be carefully checked at intervals not exceeding 12
months - dependent on the conditions under which the set is working. The
~~ set must be brought to the service workshop to be tested.
! •

J Along with each set a TEST-SHEET is delivered in which all the measurements,
made in the test department of the factory, are listed. If the control
measurings made in the service workshop should not show the same values as
those listed in the test-sheet, the set must be adjusted as specified in
the ADJUSTMENT PROCEDURE.

I
•
'

3.2. ALIGNMENT INSTRUCTIONS

INTRODUCTION
The measuring values indicated in paragraph 2 of CIRCUIT DESCRIPTION AND
SCHEMATIC DIAGRAMS are typical values and as indicated it will be necessary
to use instruments in absolute conformity with the below list:

3.3. PROPOSAL FOR NECESSARY MEASURING INSTRUMENTS

VHF Signal Generator type TF2015 MARCONI

FM Modulation Meter type TF2303 MARCONI
Distortion Analyzer type TF2337A MARCONI
AF Voltmeter type VT-121 TRIO
Tone Generator type PM5107 PHILIPS
Electronic Multimeter type PM2505 PHILIPS
RF Directional Wattmeter Model 43 BIRD
50W Load with 30 dB Attenuator type 8321 BIRD
Frequency Counter:
Frequency range >175 Mhz
Sensitivity <100 mV
Impedance >1 Mohm and 50 ohm
Accuracy <1 . 10-6
3.3. PROPOSAL FOR NECESSARY MEASURING INSTRUMENTS cont.:
J

We can also recommend one of the new communication test sets introduced by
,J
several instruments manufacturers.
From S. P. Radio this high quality product will be tested and adjusted by
·~J
means of a CMT communication tester from Rohde and Schwarz.

,,
I

\J

3.4. TEST PROBE

lnf
ceramic AA/19
ffo 1~--~---------n
TO mullimeler

il

LAYOUT OF TilE PROBE ~:

Q I
-1:'

~·
c~ I _I
I
1\)

3~
\Ci, '
·~
f·
F''".
, r
I .

All measurings made by means of a test probe will be relative measurements.

For quantitative measurings the diode probe should be calibrated by means I ,
, I
of a signal generator at a certain impedance level (50 ohm) as a function
of frequency.

'""

Cl)j
"'-\,
J 3.5. ADJUSTMENT PROCEDURE

~.
.
!J
J
3.5.1. ADJUSTMENT OF SYNTHESIZER UNIT

Alignment of Frequency Generator and RF-Levels.

1. Connect a frequency counter to the TX-driver output of J4.

J ~
2.
3.
Select channel 6 and key the transmitter.
Connect a De-voltmeter to the point between R50 and R95 and adjust L9
ml until the reading is 2.0V.
•J 4. Adjust the frequency on C77 until the counter read-out is 156.300000
MHz ±150 Hz.

1 5. Connect a power meter to the TX-driver output at J4 and adjust the

output level to minimum at R98.
6. Now the windings on coils L14, L13, and L12, Lll, LlO are moved a
little bit to obtain maximum output at J4.
7. If the output level is below 200 mW, the level is raised by means of
R98 until the power meter reading is 200 mW.
8. Release the transmitter key; the set should still be on channel 6.
9. Connect a De-voltmeter to the point between R50 and R95 and adjust C78
until the reading is 2.0V.
10. Check the RF-output level from the RX-buffer amplifier at J3. The level
should be 5 mW -1 dB, +3 dB. ~

Alignment of Modulation Circuitry.

1. Connect a modulation meter to the TX-driver output at J4, and a
distortion meter to the AF-output part on the modulation meter.

] 2. Connect tone generator and AF-voltmeter between pin 4 in the connector

for handset and ground, pin 3.
3. Select channel number 6 and key the transmitter.
4. Turn potentiometer R97 fully clockwise.
5. Set the tone generator to a frequency of 1000 Hz and output level to
100 mVRMS
6. Adjust R96 to nominal modulation: f = ±3 kHz and check that distortion
is less than 5%
7. Raise tone generator output level to 1.0 VRMS
8. Adjust R97 to maximum deviation: f = ±4.8 kHz.

,
I
3.5.1. ADJUSTMENT OF SYNTHESIZER UNIT cont.:

Alignment of RX-Filter Control Amplifier

1. The receiver must be tuned up according to the TUNE-UP PROCEDURE.
2. Select channel 28.
3. Connect signal generator to antenna connector J04.
4. Connect test probe to pin 16 at U03 on the RX/TX board.
5. Set· signal generator frequency to 162.000 MHz and output level to -30
dBm.
6. Adjust R95 until maximum output level from the test probe is reached.

3.5.2. ADJUSTMENT OF RX/TX UNIT

Alignment of Internal Power Supply
1. Select channel 6.
2. Select 1W output level and key the transmitter.
3. Connect a De-voltmeter to the test point at the output of U01.
4. Adjust the output voltage to 8V ±50 mV by means of potentiometer R04.

Alignment of RF and IF Amplifier

1. Select channel 6.
2. Connect signal generator to antenna connector J04.
3. Connect test probe to pin 16 on U03.
4. Set signal generator frequency to 156.300 MHz and the output level to
-30 dBm.
5. Adjust transformers TR01, TR02, and coils LlO, L11, L12, and L09 to
maximum deflection on the TP-meter.

Alignment of Detector and AF-Output Level

1. Select channel 6.
2. Connect signal generator to antenna connector J04.
3. Connect frequency counter between pin 3 of U03 and frame through a 10
uF capacitor.
4. Set signal generator level to -30 dBm (no modulation).
5. Set signal generator frequency until frequency couriter shows 450.0 kHz
+100 Hz.
 3.5.2. ADJUSTMENT OF RX/TX UNIT cont.:

6. Set modulation on signal generator to nominal modulation fm = 1 kHz,

f = +3 kHz.

7. Connect AF-voltmeter to the AF output at pin 11 on U03.

8. Adjust coil L06 to maximum deflection on the AF-voltmeter.
9. Adjust potentiometer R20 to 250 mVRMS ~10 mVRMS on AF-voltmeter.
10. Connect distortion analyzer to the telephone output at pin 1 on P04.
11. Make sure that distortion is minimum by slightly tuning transformer
TROl.
12. Check that distortion is below 5%.

Control of Receiver Sensitivity

1. Select channel 6.
2. Connect signal generator to antenna connector J04.
3. Connect distortion analyzer to the telephone output at pin 1 on P04.
4. Set signal generator to best sensitivity.
5. Check that the sensitivity is better than 0.5 uV EMF for 12 dB SINAD.
6. Repeat on channel 28.

Alignment of Transmitter Output Level

1. Connect RF-power meter and a 50 ohm 25 Watt 1oad resistor to antenna
connector J04. ~

2. Select channel 6 and key the transmitter.

) 3. Adjust potentiometer R21 until the reading is 25 Watt.

·~ 4. Set the output level to lW. ·

5. Adjust potentiometer R19 until the reading is 0.8 Watt.

'I
r1

t
I I
'
'

1 I
3.6. TROUBLE-SHOOTING
~
Trouble-shooting should only be performed by persons with sufficient
technical knowledge, who have the necessary measuring instruments at their
·~
disposal, and who have carefully studied the operation principles and
structure of SAILOR RT2048. lJ
4
~
The first thing to check is whether the fault is somewhere in the antenna
circuit, the power source, the handset, or in the transmitter- receiver
unit.
In order to help you during trouble-shooting, the section 5. CIRCUIT
DESCRIPTION contains diagrams, principal descriptions, and drawings showing
l'~l~J
the location of the individual components. Typical values for the DC and
AC voltages are indicated in the diagrams, and also the test points are
indicated in the diagrams.
L)
<II
SAILOR RT2048 has a number of trimming cores and trimmers, which must not
be touched unless adjustments as specified in section 3.5. ADJUSTMENT lJ
PROCEDURE can be made.
(1
When measuring in the units, short-circuits must be avoided as the
transistors would then be spoiled. '1!1
~ I
L

3.7. REPLACEMENT OF COMPONENTS

When replacing transistors, diodes, resistors, capacitors and similar

components you must use a small 11 pencil" soldering iron of 30 to 75 Watt
rating. The soldering must be performed rapidly to avoid over-heating, and
the use of a tin sucker is recommended, as otherwise there is a e-risk that
both the components and the printed circuit will be spoiled.

3.8. REPLACEMENT OF MODULES

r
If a fault has been found in a module, it may often be worth-while to
replace it and then repair it later on.
 3,9, NECESSARY ADJUSTMENTS AFTER REPLACEMENT OF MODULE

3.9,1, REPLACEMENT OF RX/TX UNIT

1. If a factory adjusted and tested module has to be inserted,~just proceed
with point 3.
2. Follow the procedure described in section 3.5.2. ADJUSTMENT OF RX/TX
UNIT.
3. Follow the procedure Alignment of RX-filter control amplifier described
in section 3.5.1. ADJUSTMENT OF SYNTHESIZER UNIT.

3.9.2. REPLACEMENT OF SYNTHESIZER UNIT

1. If a factory adjusted and tested module has to be inserted, just proceed
with point 3.
2. Follow the procedure described in section 3.5.1. ADJUSTMENT OF
SYNTHESIZER UNIT .
. 3. Follow the p~ocedure Alignment of RX-filter control amplifier described
in section 3.5.1.

f·

,
I
J 3.10. PIN CONFIGURATIONS cont.·

J MC3361
J ' Input

Audoo
4 Mute
Sun
1
Co;.nl•o!

L!n'llll"
OulP\.11 lnn111
g
~..~~
0fn'lodUIIII>'
8 L___ _- - l Quuu•t

Cryt1tl Ml.. tr Vee

0..
"""""

, MC145158
osc,.,
oseau,
Voo
POoul
r,
I

'
" .v••
• " '•
3

s
15

13
12
p;EfooJ

Vodvlu1
Con11ol
Vss
lD
• " II
10 0~·~

·~ • 00«

MC14066B t1/4 OF OEVICE SIIOWNI

·~
Ct~nt1()11
2
Outl
1

Control:ljyl
'"'
4
Out2
Out/In

Conuotljy•
'"'
f Oull
,_

'"'
... ~
Voo•PmU
Conual<l Vss•P1n 1
10
Out4
11

]
' Control
lnpul
MC12015

2
Active
Pullup

7 4
-:- Gnd

Vee
Voltage
8 Regulator
 ~
3.10. PIN CONFIGURATIONS cont.·

·~
MC74HC595
·-·
t>.'t>ul ll

L
L
c
fll

...
P.t~lf~

0ulll'!l1J l'
'W'

L
I®
')
~

93C46 EEPROM
Block and Connection Diagrams
DuaJ.In-Uno Pack•u•

f·
PlnHomaa
CS Chip Soloct
SK SOOol Oa!Q Clock
01 SOOol Oa!Q Input
DO Soria! Data Output
Vro Powor Supply
GNO Ground
NC Not Connectod

r
MC14569B
CTLA CTl.D DPOl DP82 Opo3 Dpa4
10 tt 12 13 t4
10
15
14

,.
13

,
10

v 00 •Pift1G
v8ll .. ,1.,•

1 - - - - - < l PEwt
 J 3.10. PIN CONFIGURATIONS cont.
)
J4 LM339

J
I.

J
LM324
LM393 Dusl-ln·Lirw and Ffat p~
ovmru t•vrr

LM358

MC14013B

:1J=
.
3 c
5

R
o

a
1

) '1J=
•

"
10
v 00 •Pin u
Vss ~ PJn 1
ll

MC14094B

·~

,;•'
1
I
.,.~

1
 CONTENTS

4. MODULE LOCATION
4.1. MECHANICAL DISASSEMBLING

I
I '

f·

I '
4. MODULE LOCATION

Squelch Read~out

KeyboaMI {module 11

Loudspealcer On/Off/Vel l..oudspeaker

112VJ
Strap:furrormectlon
to N420 {Z4V)

Sel~au ,

Rx/Tx. Unit imodule 4)

Synthesizer Unlt [module 3 ~

th:/Tx U o H · - - -

MODULE LOCATION RT2048

j
4.1. MECHANICAL DISASSEMBLING RT2048
J To disassemble the RT2048 remove the two allen screws with the black covers
on the rear of the set and pull the frontplate and kabinet from each other.
J
J
J

Front

I·

1
~
<
J
CONTENTS
J
5. CIRCUIT DESCRIPTION AND SCHEMATIC DIAGRAMS
5.1. KEYBOARD UNIT (MODULE 1)

5.2. INTERFACE UNIT (MODULE 2)

5.3. SYNTHESIZER UNIT (MODULE 3)

5.4. RX!TX UNIT (MODULE 4)

5.5. SELCALL UNIT (MODULE 5) OPTIONAL

5.6. INTERCONNECTION CABLE DIAGRAM

(·

. I

1
.

'
 5. CIRCUIT DESCRIPTION

5.1. KEYBOARD UNIT (MODULE 1)

The keyboard unit comprises the 3 point 4 push button matrix, which is used
for all the entries from the front panel e.g. channel selection, lW etc.
Besides the LED-diodes for keyboard illumination is placed on this board.

View from component side View from component side

with upper side tracks. with lower,. side tracks.

Keyboard Unit (1)

512
)

"-------------5-0-25447
KEYBOARD <MODULE 1)
II
I
 I
I
k;ll
'·
5.2. INTERFACE UNIT (MODULE 2)

\ (
'·

5.2.1. +5V POWER SUPPLY

The internal power supply for the logic circuitries is generated from the
internal +8V power supply, by means of the integrated voltage regulator U09.
The input voltage for U09 is fed to pin 3 via DOl, which secures an
appropriate voltage decay on C12 when the set is switched off.

5.2.2. BATTERY SENSE/RESET CIRCUIT

When the set is switched on, U07/1 which is coupled as a comparator will
generate an appropriate reset signal for the microcomputer U03.
U07/2 is configured as a comparator circuit sensing the level of the (
lo,
internal +13V supply voltage. When this voltage drops below a certain level )
determined by R27, R20, R54, and Dll a 11 Voltage low 11 signal is generated L.
on pin 1. This action is detected by the microcomputer U3 which in turn will
block the key function. r /
I

5.2.3. INDICATOR SUPPLY r~~

I
The LED read-out intensity is controlled by means of a four-step voltage I

supply. Transistor Q02 acts as the emitter follower buffer transistor. The
base voltage level of this transistor, and so the output voltage, is
controlled by means of U08/4 and the programming resistors R07, R49, R47,
and R55.

5.2.4. DISPLAY LATCH~$

The display segments and the display power supply control inputs are
buffered "by means of three serial to parallel registers included in the
integrated circuits U04, U05 and U06. The information is latched-in by means
of the internal serial data bus controlled by the microcomputer. •

5.2.5. READ-OUT
The information read-out is made by means of two seven-segment LED-displays
D06, DOl and three individual diodes for 1W, TX and US-mode 003, 010, and
012.

5.2 6. EEPROM-MEMORIES
The two rc•s UOl and U02 constitute the internal programmable memory. These
circuits are controlled by the microcomputer via the internal serial bus.
The memories are used for set identification codes, private channel
programming etc.

5.2.7. MICROCOMPUTER
All the internal control signals are supplied by the microcomputer U03,
either by means of the internal serial bus or by individual control signals
 )
J
5.2. INTERFACE UNIT (MODULE 2) cont.:

like the key function, power level etc. Besides the microcomputer reads the
I
keyboard information via the connector J01.
When a selcall unit is installed via J02, the control functions for this
module and the alarm generation are created by the microcomputer. The
audible alarm is coupled to the loudspeaker by means of resistors R26, R40,
and R46.
I
Jll
(~} 5.2.8. SERIAL INTERFACE
! ~~·
::::.
~~
For use in the factory production, a serial interface to the microcomputer
'~.'fl:.\¥;
is implemented by means of U07/4 and transistor Q01.
~~
J,,•
5.2.9. SQUELCH
The AF signal from the discriminator amplifier on RX/TX board is fed to the
active squelch filter around U08/2, which is a highpass filter with a roll-
off frequency of 45 kHz. The signal is amplified about 6-8 dB.
The amplitude of the noise signal is adjustable from the front panel by
means of the squelch potentiometer R10.
Q05 amplifies the signal to the squelch detector. If there is a noise
signal (without carrier at the receiver), the detector generates a DC
voltage at pin 9 on U08/3. When this voltage increases to 0.6V, which is
the same as the voltage at pin 10 on U08/3, the comparator output goes low
and the squelch mute message is generated via Q08.
The microcomputer U03 detects the message and generates the appropriate mute
signals for the AF amplifiers.

5.2.10. AF FILTER/AMPLIFIER
The AF signal is led to the active filter around U08/l. The filter provides
a frequency response of -6 dB/oct. in the range of ~.3 to 3 kHz, and limits
the signals outside this range.
Q0.4 is an emitter follower buffer amplifier, which supplies the earphone
and the AF power amplifier. The uC controls the mute function via Q06 and
Q03. When Q06 is off the DC voltage at pin 3 and 1 is 8V and therefore Q04
is off.
The loudspeaker level is adjustable by means of the volume control R23.

I I )

,, I
)
 RT2048
~.
~ ,..
t·

L (

L
L~·-\i
L.:
L
t'

!Lr.
!
View from component side with upper side tracks. L

[$..•,'1-l"

.
I (

r~

)r.j. '

'

rr
r~,

View from component side with lower side tracks.

PCB rev. 25450L

9725
INTERFACE UNIT (MODULE 2)
 RT2048

INTERFACE UNIT MODULE 2

This diagram is valid for PCB rev. 254501

9726
 5.3. SYNTHESIZER UNIT (MODULE 3)

5.3.1. VCO with Buffer

The voltage controlled oscillator, built around the Field Effect Transistor
Q18, is osci 11 ati ng either on the transmitting frequency or on the first
receiver local oscillator frequency, which means the receiving frequency
less 15.3 MHz. To reach this function, the oscillator is implemented with
a bandshift by means of the bandswitch diode 06 and the two capacitors C47
and C78.
In transmit mode, where the diode 06 is reverse biased, the osci 11 ati ng
frequency is mainly determined by C48, L9, C49, C51, and 09.
In receiving mode the oscillator resonance frequency is 1owe red 15.3 MHz
by switching 06 on and thus putting C47 and C78 in parallel with C48.

] The oscillating frequency is varied by means of the control voltage fed to

the capacitor diode 09.
The output voltage from the VCO is taken via a capacitive tap C52, C53 on
the source of Q18 and fed to the common buffer amplifier, built around Ql5.
The power gain of this stage is adjusted by means of potentiometer R98. The
gain is adjusted so that the output level from the TX buffer amplifier is
200 mW measured at the output connector J4.

5.3.2. loop Buffer Amplifier

The output from the common VCO buffer is fed to the divider chain via the
stage around Q7, which secures the needed amplification and the reverse
isolation between the digital parts and the VCO.
The amplifier is a fixed tuned broad band amplifier with L1, C24, and R47
forming a low Q tuned circuit.

5.3.3. 32/33 Prescaler

The integrated circuit U4 is a two modulus presc~ler based on the ECL
technique.
From the control logic in the programmable divider U3 pin 12, a high or low
level is led to the prescaler U4 pin 1. A high level at U4 pin 1 causes the
prescaler to divide by 33 and in turn a low level at pin 1 sets it up for
dividing by 32.
The resistor R20 and the diode 04 work as a speed-up and overdrive
protection circuit.

i. !
5.3.4. Reference/Programmable Divider and Phase Detector
The integrated circuit U3 comprises both a programmable divider for the
reference input and a programmable divider with control logic for use in
conjunction with a dual modulus prescaler. Besides, the IC includes two
phase detectors and a lock detector of which only on~ of the phase detectors
is in use, the output pins located at pin 15 and pin 16.
Both dividers are programmed via the serial bus from the microcomputer. The
coding structure of the serial data stream includes the needed information
for the on-chip decoder to detect the kind of the reached division figures.
The reference division ratio is constant as the input of 3.7125 MHz is
derived from the X-tal oscillator.

',
1 '
5.3. SYNTHESIZER UNIT cont.:

In the beginning of a counting period the prescaler U4 starts dividing by

33. After a few counts the modulus control pin changes level and the I
!l@;'l
prescaler will finish the dividing cycles with a division ratio of 32,
ending up with the correct total division ratio.
The pulse frequency out of the reference divider is 12. 5 kHz. If the VCO
frequency is correct the pulse frequency from the variable divider is also
12.5 kHz and in phase with the pulse from the reference divider. The on-chip
phase detector compares the phase of the two pulses. If they are out of
phase the detector creates correction pulses to the Charge Pumpe for
correction of the VCO frequency/phase.
However, the synthesizer circuit is made with a small constant phase error,
forced by the current drawn through R58, to avoid phase detector non
linearities to degrade the loop performance. So the phase detector is
sending small correction pulses to transistor Q4 with a frequency of 12.5
kHz.

5.3.5. Charge Pumpe

The charge pumpe, mainly consisting of Q4, Q5, and 02, converts the pulse
with modulated phase detector outputs of U3 pin 15 and 16 to a DC current
flowing into or out of the loop amplifier.
Assume that the VCO frequency has decreased from its ·nominal value. The
phase detector wi 11 produce a negative correction pulse on pin 16, turning
Q5 on, resulting in current being drawn out of the loop amplifier.
This action will cause the output voltage to increase, thus increasing the
VCO frequency to the nominal value.
An increase in VCO frequency from its nomina 1 va 1ue wi 11 in turn cause a
correction pulse on pin 15, turning Q4 off, resulting in current flowing
into the loop amplifier through the diode 02. This means the output voltage
will decrease, forcing the VCO frequency to decrease.
Because of the current drawn through R58, a small correction pulse of about
500 nsec wi 11 always be present at pin 15 on U3 with a frequency of 12.5
kHz. ~

5.3.6. loop Amplifier/Filter

r
i

The 1oop amp 1i fi er is rea 1i zed as a discrete operation a 1 amp 1ifi er with
t·ransistors QlO and Qll forming the input differential pair and Q8, Q9 the
output stage.
The loop dynamic performance is mainly controlled via the feed-back
components in the loop amplifier, this means capacitors C29, C30, C31 and
R49. The output from the 1oop amp 1ifi er is further filtered in a 1ow pass
filter formed by C36, L2, C34, and C35, to reduce the level of the reference
frequency sidebands on the VCO output.

5.3.7. RX Buffer Amplifier

When receiving, the bandswi tch diode 08 is turned on, and the output from
the VCO buffer amplifier is further amplified in a single tuned amplifier
formed around Ql6 with L8, C70, and C73 forming the tuned circuit. The
output is attenuated and impedance matched by means of resistors R93 and
R94. The typical output level at connector J3 will be 5 mW.
,J
5.3. SYNTHESIZER UNIT cont.:
J
5.3.8. TX Buffer Amplifier
When the set changes to transmit mode, the band switch diode 07 wi 11 be
turned on and the output from the VCO buffer amplifier will be fed to the
two stage amplifier cicuit.
The level is amplified to about 30 mW in Q14 and the final stage with Q13
boosts the level to about 200 mW measured at connector J4.
The first stage is working as a class A amplifier with the base on Q14
biased through R80, 07, R79, and R86. The output stage is working as a class
C amplifier with a small base bias through resistors R72 and R73.

5.3.9. X-Tal Oscillator

The oscillator is of a Colpitt type and the oscillator transistor Q1 is
oscillating by means of a 14.850 MHz crystal X1.
The trimmer capacitor C77 is for fine adjustment of the oscillator
frequency.
RF signal for the second,mixer in the receiver is taken from the collector
of transistor Q1, connector J1.
The oscillator signal is buffered and amplified in transistors Q2 and Q3
before it is fed to the reference divider.

5.3.10. Reference Divider

The fixed divide by four reference divider U2 divides the X-tal oscillator
frequency down to 3. 7125 MHz before it is fed to the microcomputer vi a
connector J2 and the phase locked loop reference divider included in U3.

5.3.11. RX Filter Control Amplifier

This variable slope DC amplifier made by means of ar operational amplifier
U1 converts the VCO control voltage to an appropriate control voltage for
the variocap. diode tuned filters in the receiver front-end.
The maximum output voltage is adjusted by means of potentiometer R95.

5.3.12. Preemphasis Network

Capacitor C18 in conjunction with R35 and R96 introduces the needed 6
dB/oct. response of the AF input signal. The input sensitivity is adjusted
by means of R96.

5.3.13. AF Amplifier/Compressor
This circuit, formed around two operational amplifiers in U1, comprises both
an amplifying and voltage limiting function. Amplifier No. 3 is a fixed
voltage amplifier, the output of which is sensed by means of the comparator
made by amplifier No. 2. When the peak output voltage exceeds a certain
level, adjusted by means of potentiometer R97, the comparator will turn on
transistor Q6, which in turn will charge capacitor C14. So the gate-source
voltage on transistor Q17, acting as a variable resistor, will decrease and
also the AC resistance between pin 10 on Ul and ground, which in turn will
reduce the input level to the amplifier.
The rise-time of the compressor is mainly determined by resistors R38, R31,
and capacitor C14. The decay-time by C14 and R30.
5.3. SYNTHESIZER UNIT cont.:

5.3.14. AF Post Filter

This second order active filter, built around operational amplifier No. 4
in Ul, secures an appropriate high frequency roll-off of the AF signal.
Resistors R64 and R65 give an appropriate attenuation of the AF signal
before it is fed to the modulating diode 06 in the VCO.

L
L"

L_

View from component side with upper side tracks.

View from component side with lower side tracks.

PCB rev. 25451 H

SYNTHESIZER <MODULE 3)
 SYNTHESIZER UNrT MODULE 3
RT2048
®
Synthesizer Unit (3)

SOm'V/OIV 1VJDN
20nSIDIV tOuSIDIV

®@
I

,
i/ 1/
I
I
!=
1
l WIOIV 1VIOIV
20CuS/01V 50nSIOIV

® ®
I
(
I
I
I
I I
I I

1VJDIV 1VIDIV'
5CnsnJIV SOnS/DIV

©
i ,
CH
_L
f I

n
lVJDIV tiSVIMifOJion!y
100nSIOIV RSI~k~ fSPI!:l.1Val
~ tSPa:l.~&Sl
xst<ippaClii7StSP3S.91tl

,,.
This diagram lsvaJJa for PCB rey.25451H
~
5.4. RX/TX UNIT (MODULE 4)
~
The RX/TX unit comprises the following circuits:
J The receiver including detector
AF power amplifier
J RF power amplifier
Harmonic filter
RF power control
&I 8V power supply

5.4.1. RECEIVER FRONT-END

The RF amplifier covers the frequency range 154.400 MHz to 163.600 MHz and
J consists of the low noise Dual Gate Si-Mos-FET 011 surrounded by two high 0
double-tuned bandpass filters.
From the aerial the signal is led through the aerial relay to the receiver
input bandpass filter. The input bandpass filter as well as the intermediate
bandpass filter are controlled by a DC voltage on the tuning diodes. This DC
voltage derives from the RX VCO control voltage and secures an optimum filter
response in the whole frequency range of the receiver.
The two bandpass filters create the necessary attenuation of unwanted signals.

5.4.2. FIRST MIXER

The balanced mixer has good large signal properties, securing good
intermodulation characteristic.
'The mixer transistors 008 and 009 are of the J-FET type.
The signal is led to the balanced input transformer TR2 and then to the gates
of the J-FETs, which are switched by injecting the first LO signal into the
· sources. The mixed signa 1s are fed to the ba 1anced output transformer TRl
where the wanted signal on 15.3 MHz is selected by the tune circuit consisting
of TR1 and C75.
R06 and R01 create the necessary impedance matching the IF crystal filter.

5.4.3. CRYSTAL FILTER

The receiver adjacent channe 1 se 1ect i vity is rna i nta i ned by means of the
crystal filter FL2 in co-operation with the ceramic filter Fll.
R57 and R39 give the impedance matching the crystal filter output.

5.4.4. IF AMPLIFIER
The transistor 010 amplifies the signal to the 2nd mixer, which has a tuned
drain circuit consisting of L04 and C32.
R34 creates the impedance matching the 2nd mixer.

5.4.5. SECOND MIXER, CERAMIC FILTER, DETECTOR AND AF AMPLIFIER

The second LO signal 14.850 MHz is amplified in 002 before it is delivered to
the mixer.
 I
I

fCHEMATIC 0II\GRAM RX/TX UN IT <MODULE

-----··--- ·-- - -----------------------·----- -·--·---------------

--····---·--·---- -------------------
J 5.5. SELCALL UNIT CMODULE 5)
J
J The input to the se 1ca 11 is taken from the te 1ephone output. The signa 1 is
first amplified and limited in U04/2 and then it passes the bandpass filter.
Finally the signal is rectified and compared with a reference level in the
comparator U04/1.
J 3.7125 MHz is divided in the programmable counter U06. The output of this
is divi·ded by 2 and turn·ed into a square wave in the flip-flop U03/2. The
outputs of the flip-flop is connected to the switches U02. The frequency,
tJ at which the switches around the capacitors C03 and C04 are working,
determines the resonance frequency of the filter. Thus by changing the
dividing figure to U06, it is possible to change the resonance frequency
~
t?jj
of the filter.
With R01 it is possible to fine adjust the resonance frequency of the filter
(see the adjustment procedure).
Figure f(nominal) U06 input U03 output
No. (Hz) 14 13 12 11 6 5 4 3 (Hz)
1 1124 0 1 1 0 0 1 1 1 18022
2 1197 0 1 1 0 0 0 0 0 19336
3 1275 0 1 0 1 1 0 1 0 20625
4 1358 0 1 0 1 0 1 0 1 21838
5 1446 0 1 0 1 0 0 0 0 23203
6 1540 0 1 0 0 1 0 1 1 24750
7 1640 0 1 0 0 0 1 1 0 26518
8 1747 0 1 0 0 0 0 1 0 28125
9 1860 0 0 1 1 1 1 1 0 29940 ::u
0 1982 0 0 1 1 1 0 1 0 32004 -l
1'\)
R 2110 0 0 1 1 0 1 1 1 33750 0
-!="
en
OJ
When the radio is switched on the dividing figure, corresponding to the
first figure in the selcall number, is shifted out on port BO on· the uC at
the interface unit which is connected to the input of U07.
U07 is a serial to parallel shift register which converts the s1gnal to the
di vi ding figure U06. If the correct tone is received the ou:tput of the
comparator U4/1 goes low. This output is connected to the uC's SEL-DET. pin.
When the tone disappears again the uC will put out the dividing figure
corresponding to the next figure in the selcall number.
If all five tones are received correctly, the port C06 (EXT. ALARM) on the
uc goes high. This port is connected to pin 1 on the connector to the option
board at the RX/TX unit. At the same time the uC will send out an alarm tone
from 006 via the volume control and power amplifier to the loudspeaker. The
alarm tone lasts for 10 sees after an individual call, and after an all call
it lasts until the selcall has been reset.
If the SELCALL T/R button is activated the· alarm circuits and indicators
are tested.

Ii
 Se 1ca 11 Unit (5)
Jai

~
~
'
~
j
>
m
+

:1_,

1
,,

.,

4-0-25449 D

View from component side with upper side tracks. View from component side with lower side tracks.

PCB rev_ 254498

SELCALL UNI .MODULE 5)

5.6. INTERCONNECTION CABLE DIAGRAM

Rx/Tx Unit {4) 10 Interface Un1t {2)

Keyboard Unit (1)
P1-4
J3-4

J1-4
j oo.ooooo<>oooo!
12
J4-4
MlCROTELEPHONE
4
ohm

' - - - · - S-0-2St.t.7 5-0-15450

l1..::L !TO P01 ON OPTION UNIT (61 1

1 ALARM
2 AUX I
3
4.
AUX II
TELEPHONE
"
5 GNO
6 DISTRESS a
7 +13V !NT c;
8. EXT MUTE LS
9 MIC IN
10 MIC OUT
11. KEY j
12 MUTE AF-AMP. "
v

Selcall Urut {5)

{option)

Synthesizer Unit { 3) J1-3

' - - - - - - - - - - - - - - - - - - - s~o-25451

INTERCON, .TION CABLE DIAGRAM RT2048

 '

J
CONTENTS
J
6. MICROTELEPHONE INSTALLATION

J 6.1. SPECIAL INSTALLATION WITH 2 MICROTELEPHONES

,J 6.2.
6.3.
SPECIAL INSTALLATION WITH 3 MICROTELEPHONES
MECHANICAL DIMENSIONS FOR HANDSET

J,,
I
~ ,:
:·:·

~4

J
WJ
~
~,<l
I

f·

,I
''

'
 RT2048
6. MICROTELEPHONE INSTALLATION

VHf! AT2047 SCRAMBLER CRY2001, AE2100, RT2047 prepared lor DSO and AT204S SHORlWAVE S13QX

R~D
YELLOW

TCB01

1--
HANDKEY

WHITE YELLOW

ov~ ov~
etM
0.6msecJDIV
t·
~ 0,5msec/OIV

MIG. PRE-AMPLIFIER (100)

+10·18v

* In orange marked m!crolelephono cartridij(l, A21s changed horn 1ka to 5k6 ohm. 27777A

9649
 RT2048

~
MICROTELEPHONE WITH ELECTRET MJC. AMP. ECI A/S 4·6·24025D/4·0·24025E 600875

POSITION DESCRIPTION MANU FACTOR TYPE PARTNR.

C1 CAPACITOR ELECTROLYTIC 100uF 20% 10VDC ERO EKI 00 BB 310 C MOE 14.607
C2 CAPACITOR CERAMIC 10nF ·20/+80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C3 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2·35-V·100·M·T34(T58) 14.512
C4 CAPACITOR ELECTROLYTIC 0.47uF 20% 50VDC ELNA RJ3-50-V-R47·M·T34 14.504
C5 CAPACITOR ELECTROLYTIC 2u2F 20% 50VDC ELNA RJ2-50-V-2R2·M·T34 14.503
C6 CAPACITOR ELECTROLYTIC 2u2F 20% 50VDC ELNA RJ2·50-V-2R2·M-T34 14.503
C7 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2-35·V·100·M·T34(T58) 14.512
C8 CAPACITOR CERAMIC CL2 1nOF 10% 100V PHILIPS 2222 630 63102 16.149
C9 CAPACITOR CERAMIC CL2 1nOF 10% 100V PHILIPS 2222 630 63102 16.149
C10 CAPACITOR ELECTROLYTIC 33uF 20% 16VDC ELNA RJ2-16·V·330·M-T34 14.518
C11 CAPACITOR CERAMIC 1OnF -20/tBO% CL2 50VDC KCK RT-HE70 SK YF 103 Z 15.170
C12 CAPACITOR CERAMIC 27pF 10% N750 500VDC KCK RT·HM60·SK UJ 270 K 16.062
C13 CAPACITOR CERAMIC 27pF 10% N750 500VDC KCK RT·HM60-SK UJ 270 K 16.062
C14 CAPACITOR CERAM. SMD 0805 15pF 5% NPO 50VDC MURATA GRM40 COG 150 J 50 PT 323.076
D1 DIODE 1N4148 HIGH SPEED PHILIPS 1N4148·143 25.131
MC1 MICROPHONE ELECTRET •9.7x6.7mm PANASONIC WM·0344BY 46.012 t
R1 RESISTOR MF 1k8 OHM 5% 0.33W PHILIPS 232218773182 02.478
R2
R3
R4
RESISTOR MF
RESISTOR MF
RESISTOR MF
1k8 OHM 5% 0.33W
8k2 OHM 5% 0.33W
18k OHM 5% 0.33W
PHILIPS
PHILIPS
PHILIPS
2322187 73182
2322 187 73822
232218773183
02.478
02.494
02.502
J
R5 RESISTOR MF 2k7 OHM 5% 0.33W PHILIPS 2322 187 73272 02.482
R6 RESISTOR MF 4k7 OHM 5% 0.33W PHILIPS 2322 18773472 02.488
R7 RESISTOR MF 2k2 OHM 5% 0.33W PHILIPS 2322 187 73222 02.480
R8 RESISTOR MF 6k8 OHM 5% 0.33W PHILIPS 2322 187 73682 02.492
R9 RESISTOR MF 2k7 OHM 5% 0.33W PHILIPS 2322 187 73272 02.482
R10 RESISTOR MF 120k OHM 5% 0.33W PHILIPS 232218773124 02.522
R11 RESISTOR MF 39k OHM 5% 0.33W PHILIPS 2322 187 73393 02.510
S1 MICROSWITCH E62·10H PDT CHERRY E62·10HPDT 44.025
T1 TRANSISTOR AF NPN BC547C T0-92 PHILIPS BC547C-126 28.068
T2 TRANSISTOR AF NPN BC547C T0-92 PHILIPS BC547C·126 28.068
T3 TRANSISTOR AF NPN BC547C T0-92 PHILIPS BC547C·126 28.068
TC1 TRANSDUCER DYNAMIC FOR HANDSET •31x18mm 200 OHM S.E.K. (KIRK) T802 0113 2715 46.010
<'-
·'
I

9649
~
I
 6.1. SPECIAL INSTALLATION WITH 2 MICROTELEPHONES:
H2086 FOR SCRAMBLER CRY2001 AND RT2048
H2087 FOR VHF RT2047 AND SSB T2031

MICROTELEPHONE ONE WITH PREFERENCE

H20& NOR/1Allt!C/l0Tl/IPHONE
HllllfffEJEPIIOHl
f¥T!J"lm 2(}(K) (HWIJSET f.)

~~
ClJHNlCTOR lor

({)
j '
CRY 2/){)/ AND RT20~0
BAf!W/1
'BI/OWII
(
.• 1 I

'
I
I WHfff.
L-"'=-----;;-.
I ------i
1/AIIIIJtJ:/1
ftC,ff/E-MP /(;

, - - )..,__ The cahle helrottn lht '/hoM.

' - -- - ' is ttl rcciory deldrtml O• O.l~mmlJ

11/CRUTEIEPIIlJHE
HOOk 2/3 (twmSET 2)

8//0WN
~~~~
L---"'""'-----:1:-. --- ----l
lllt/ll} H£Y2

II/C. PI?E ·AIIP I1C

St. 2 is JhrJWh with miCJOklepllone m Hook

Rearnmm:led coiJJe ieJ¥11 /110¥. 20 meietS.
II lltcre iS 'Hum· or noise ptoliems wilh /he
fTI(I(k;I(1ROII, thf. 'fiiiH1d wires oVhile ond yellow
In PJ musl he sepnro!ed. !1:1/ow wirz on fln 2,
while wi~ {)fl Ptn 7.
6.2. SPECIAL INSTALLATION WITH 3 MICROTELEPHONES:
H2088 FOR SCRAMBLER CRY2001 AND RT2048
H2089 FOR VHF RT2047 AND SSB T2031

MICROTELEPHONE ONE WITH PREFERENCE

H2008 H2089 tiORI'W. 11/CIK!Tfl.!PHONE.

lf!CKOTELEPHONE 11KI?OTEI.EPHONE
r HOOJ< 1 pro!Jf'Of112000 (HANDSET I)

~
CONN/1:TOR for

tl
CONHEOUR k!r lffNt7
CRY 2001 A/10 Rl2rNIJ Ollti T21JJI
f!ro)H( IJRIJWN
( NED

ORED
I I
llE0I!I.
Ill
v<llflW

vmnw I l'l1J

v€t I
RI'()WN

l WllfT£ I W111JW

Wl/ITF 2
I
II
Ill II£

WHITE
I -----

~I
PJJ/F I 1/AMJKCII

- }___] 12 I l
in(x/U 1)_, mww
t@'N£Vtt..W ~

"'" ' 1 . ~~ ~~~

:": l S·O·ttt41 ~ ..-
~~

~ N~L
.j'/ -:;:., f --
- D- Tile
{
- ro& hei!I'WI flit: Hoot~.
IS rol (acloi!J tft/dyemf ( 7•0.14mnl)

~~2WWM) ~ HICROTELEPIION£
W/1/Tf HOOk. 2 I3 (HANI1S02)

f~ow }

fffl
REO
...J1!l!!ti!L IJRIJWN !, J_ YfllJM

fl!ll
..., Bf/OWII
t€t BIJJ£
YEllOW "'

~
-1

~-- "'
W/1/Tf. 1:;: WHITE
"<...
-
I ' HC

U:NlCTIIAV
module I) lJaWJ
J-D·ZfMI~
.
~
"""'

PJ

~LJ 't/H/TE
YWJJ'II
li'F1l

HICROTEI.£PIIt..WE
HOOX 2/3 (HflJIOSff .1)

~
RED
IWW/1 ~ ~
7 II
YFIInW

N£0 ~ 6 II 111>1JWII

W'llnw ~ !@ I 11/J/F

W!I/TI!. ~
3
2::;: I wNtTF I -------
~--
IWIDKEY3
It;
I
~
0
\Z!NlCTION BOARD
tncdu/e I)
5·0·&2818 .....

N"~l~ St. 2.3 is s/lown wllh microlekp/H:ne In Hoof

:wJ Ra:ornmi!J1d(ff coiJ!e lr:rg/h nm. 2Dmekts.
RED
PJ!(J;OJ If /herr iJ 'Hum· or fl(}/se problems ;Iiiii lllf modulo/ton,
lllf grwro ~res ~tl~aw yfi/aw In PJ artJ P~ must be
sq»raied. Yellow Wtre m Pin 2. While wire on fllil 7
 6.3. MECHANICAL DIMENSIONS FOR HANDSET

81

/
I
64 I
I" '"I .,
0
r- - - - - I
,---,

~ .."' I
I I
I 04.6
0 '-· I
0 0
I I
I I
~ "'... I I
I I
0 0 IS I 04.5 I
0 r---·
I
II
~
!;/
I
I
'-- li! ' - - 1---- --
\ I
'- ~
/

32 32

MECHANICAL DIMENSIONS FOR HANDSET HOLDER WITH MICROSWITCH

103

' '
;
......
/
I \
I· I I \
r-I
64 {
,---, ---- ~

~ 0 '-
fJ
I
I e4.5
I
I
I
0 I I
I I
0 0 l!l I I
I I
I •4.5 I
0 I
fJ
II I

l '
'---- r - - --
I

\ I
'-
32
- /

32

1 f
 l
RT2048

MECHANICAL DIMENSIONS FOR HANDSET

•
78

......
/
I
I
"\I
0

---~~~
"'

@ j""~l
'u04.slll
IU ~ I
f! "'"' lu Ill
lu ~~~
[;1 I 04.6 1 I
@

4-0-29938
~- !.
,;:" '~
0

"'
\ I
'
32
/

32

..•J
I

i
i
... !

MECHANICAL DIMENSIONS FOR HANDSET HOLDER WITH MICROSWITCH

103

/ ......
I~ \
64 \
I
lil c-+-----~
I I
~
I I
@ I 04.5 I
I I
I I
~ lll I I
I I
[;1 I 04.5 I
@
I
~
II I
I
lil '--- r - - - --
\ I

4-0-29937
'
32
- 32
/
 CONTENTS

7. PARTS LIST

I
- ·-

f·
 RT2048

7 PARTS LIST
SIMPLEX I SEMIDUPLEX VHF RT2048 STANDARD S.P. RADIO AIS VHF RT2048 (STANDARD) 802048

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

VARIOUS KEYBOARD FOIL RT2048 ECINS 1·0·25434C 225434

VARIOUS MINI114 BOX CABINET SAILOR GREEN 225435 GR0N RILSAN 22543500
ALUMINIUM
VARIOUS POWER CABLE WITH PLUG ECINS 503758 POWERKABEL 503758
VARIOUS BASE UNIT RT2048 STD. ECINS 702048
VARIOUS MICROTELEPHONE w. CRADLE CRY20011RE21 OOIRT2048 ECINS 3·0·25772 725772
VARIOUS ECINS GR0N 727206
VARIOUS AERIAL PLUG PL259 'RODAN PL259/LODDEIBAKELIT INDL. 78.502
VARIOUS OPERATION INSTRUCTIONS RT2048 S.P.RADIO NS B2048

J VARIOUS
VARIOUS
-SPEC
SERVICE AND SALES AGENTS
MANUAL RT2048 ENGLISH
BUS-INTERRUPT OPTION (6)
ADRESSES WORLD WIDE

RM2042
S.P.RADIO NS
S.P.RADIO NS
ECINS 5·0·26945B I 4-0-26945
F1000GB
M2048GB
626945

SIMPLEX I SEMIDUPLEX VHF RT2048 USA S.P.RADIO AIS VHF RT2048 (USA) 812048

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

VARIOUS KEYBOARD FOIL RT2048 ECINS 1-0-25434C 225434

VARIOUS MINI 114 BOX CABINET SAILOR GREEN 225435 GR0N RILSAN 22543500
VARIOUS FRONTPLATE RT2048 SAILOR GREEN ECINS 141A764 LAK 22544000
VARIOUS SILICONE SEAL FOR CABINET NORD.ELEKTR. 0-4-25397A 48.585
632-2456·00-X
VARIOUS KNOB 010mm SANDER PLAST 0·3·25432A 48.693
VARIOUS KNOB 030mm SANDER PLAST TG.NR.:0-3-25433B 48.694
VARIOUS FUSE COVER SANDER PLAST Tg.Nr: 0-3-25362B 48.696
VARIOUS COVER FOR ALLEN SCREW SANDER PLAST 0-3-25350A 48.699
VARIOUS POWER CABLE WITH PLUG ECINS 503758 POWERKABEL 503758
VARIOUS CONNECTION CABLE FOR LOUDSPEAKER AFD.32 3·0·25463 525463
VARIOUS MAIN INTERCONNECTION CABLE RT2048 3M 3-0-25462B 56.004
VARIOUS MICROTELEPHONE w. CRADLE CRY20011RE21 OOIRT2048 ECI NS 3·0·25772 725772
VARIOUS AERIAL PLUG PL259 'RODAN PL259/LODDEIBAKELIT INDL. 78.502
VARIOUS ANTENNA JACK (FEMALE) S0239 KAJ V HANSEN S0239 78.504
VARIOUS SCREW Pl02.9 x 16MM A2 EJOT GMBH KB30x16 WN-1442IA2 88.103
VARIOUS OPERATION INSTRUCTIONS RT2048 S.P.RADIO NS B2048
VARIOUS SERVICE AND SALES AGENTS ADRESSES WORLD WIDE S.P.RADIO NS F1000GB
t·
VARIOUS MANUAL RT2048 ENGLISH S.P.RADIO NS M2048GB
VARIOUS COAX CABLE 03x23cm ECINS 3-0-25471 525471
VARIOUS COAX CABLE 03x23cm ECINS 3·0-25471 525471
·1 KEYBOARD MODULE RT2048 ECINS 5-0-25447 625447
·2 INTERFACE MODULE RT2048 ECINS 5-0·25450L I 4-0-25450N 625450
·3 SYNTESE MODULE (USA) RT2048 ECINS 5-0-25451 H I 4-0·25451 N 625551
·4 RXITX MODULE RT2048 ECINS 5·0-25448M I 4·0·25448K 625446
·5 SELCALL MODULE (OPTIONAL) RT2048 ECINS 5-0-25449B I 4·0·25449D 625449
-SPEC BUS-INTERRUPT OPTION (6) RM2042 ECINS 5·0-26945B I 4-0-26945 626945
VARIOUS MICROTELEPHONE FOR CRY2001, RT2048 & RE21 00 ECINS 700118 MICROTELEPHONE 700116
LS1 LOUDSPEAKER 4 OHMS 15W 88x88mm RIGHT ELEC. S-881252-035P 46.052
I
··'

SIMPLEX I SEMIDUPLEX VHF RT2048 NEDERLAND (10) S.P. RADIO AIS VHF RT2048 NL (10) 832048

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

VARIOUS MINI 114 BOX CABINET SAILOR GREEN 225435 GR0N RILSAN 22543500
ALUMINIUM
VARIOUS KEYBOARD FOIL RT2048 NEDERLAND (10) ECINS 1·0-26179 226179
VARIOUS POWER CABLE WITH PLUG ECI NS 503758 POWERKABEL 503758
VARIOUS STICKER 'BV" MELSEN 9-3-24436 53.248
VARIOUS BASE UNIT RT2048 STD. ECINS 702048
VARIOUS MICROTELEPHONE w. CRADLE CRY20011RE21 OOIRT2048 ECINS 3-0-25772 725772
ECI NS GR0N 727206
VARIOUS AERIAL PLUG PL259 'RODAN PL2591LODDEIBAKELIT INDL. 78.502
VARIOUS OPERATION INSTRUCTIONS RT2048 S.P.RADIO NS B2048
VARIOUS SERVICE AND SALES AGENTS ADRESSES WORLD WIDE S.P.RADIO NS F1000GB
VARIOUS MANUAL RT2048 ENGLISH S.P.RADIO NS M2048GB
·SPEC BUS-INTERRUPT OPTION (6) RM2042 ECINS 5-0-269458 I 4-0-26945 626945
9724 PAGE 7-i

I
I
7 PARTS LIST RT2048

I
~
(
SIMPLEX I SEMIDUPLEX VHF RT2048 (RHEIN) S.P. RADIO A/S VHF RT2048 (RHEIN) 842048
'
I

POSITION DESCRIPTION MANUFACTOR TYPE PART NO. ~

VARIOUS MINI1/4 BOX CABINET SAILOR GREEN 225435 GR0N RILSAN 22543500
j
ALUMINIUM
VARIOUS
VARIOUS
KEYBOARD FOIL RT2048
POWER CABLE WITH PLUG
NEDERLAND (16) ECI NS
ECINS
1·0·25577
503758 POWERKABEL
225577
503758 ~-.
VARIOUS STICKER "BV' MELSEN 9·3·24436 53.248
VARIOUS BASE UNIT RT2048 STD. ECINS 702048
VARIOUS MICROTELEPHONE w. CRADLE CRY2001/RE2100/RT2048 ECINS 3-0·25772 725772
ECINS GR0N 727206
VARIOUS ATIS OPTION FOR RT2048 ECINS 0·0·28665 728665
VARIOUS AERIAL PLUG PL259 'RODAN PL259/LODDEIBAKELIT INDL. 78.502
VARIOUS OPERATION INSTRUCTIONS RT2048 S.P.RADIO NS B2048
VARIOUS SERVICE AND SALES AGENTS ADRESSES WORLD WIDE S.P.RADIO NS F1000GB
VARIOUS MANUAL RT2048 ENGLISH S.P.RADIO NS M2048GB (
i
6,,

L.

f.
r
'

9724
PAGE 7-2

r
(~ 7 PARTS LIST RT2048

J i

BASE UNIT RT2048 STD. ECI AIS 702048

.J POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

J VARIOUS

VARIOUS
VARIOUS
VARIOUS
SILICONE SEAL

KNOB 010mm
FUSE COVER
' COVER FOR ALLEN SCREW
FOR CABINET NORD.ELEKTR

SANDER PLAST
SANDER PLAST
SANDER PLAST
0-4-25397A
632-2456·00-X
0·3·25432A
Tg.Nr: 0·3-25362B
0·3·25350A
48.585

48.693
48.696
48.699

il
~
J . VARIOUS
VARIOUS
VARIOUS
CONNECTION CABLE FOR
MAIN INTERCONNECTION
ANTENNA JACK (FEMALE)
LOUDSPEAKER
CABLE RT2048
S0239
AFD.32
3M
KAJ V HANSEN
3·0·25463
3·0·25462B
80239
525463
56.004
78.504
VARIOUS SCREW PT 02.9 x 16MM A2 EJOTGMBH KB30x16 WN-14421A2 88.103

~
VARIOUS COAX CABLE 03x23cm ECI AIS 3·0·25471 525471
~~
ttP.' VARIOUS COAX CABLE 03x23cm ECI A/S 3-0·25471 525471
-1 KEYBOARD MODULE RT2048 ECI AIS 5-0·25447 625447

1
·2 INTERFACE MODULE RT2048 ECI A/S 5·0·25450K I 4·0·25450N 625450
·3 SYNTESE MODULE RT2048 ECI A/S 5-0·25451H 14·0·25451P 625451
~
-4 RXITX MODULE RT2048 ECI A/S 5·0·25448L I 4·0·25448K 625448
·5 SELCALL MODULE (OPTIONAL) RT2048 ECI AIS 5·0·25449B I 4-0-25449D 625449
VARIOUS MICROTELEPHONE FOR CRY2001, RT2048 & RE2100 ECI A/S 700118 MICROTELEPHONE 700118

I
JS}.~
m
LS1 LOUDSPEAKER 4 OHMS 15W 8Bx88mm RIGHT ELEC. S-881252·035P 46.052

'
KEYBOARD MODULE RT2048 ECI AJS 5·0·25447 625447

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

D1·1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP-7019 25.649
D2-1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP·7019 25.649
D3-1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP-7019 25.649
D4-1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP-7019 25.649
D5-1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP·7019 25.649
!~,' I
t;·
06-1 DIODE LIGHT EMITIING SUB MINIATURE YELLOW H.P. HLMP-7019 25.649
-*ih Jl-1 INTERCONNECTION CABLE 10 POLES L=60mm MOL EX 3-0-25465B 56.003
RH RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R2·1 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
:~t~
·'I
~(
fN
S1·1
S2·1
SWITCH KEYBOARD
SWITCH KEYBOARD
12x12mm
12x12mm
ALPS
ALPS
SKHCAD (KHC 10904)
SKHCAD (KHC 10904)
43.601
43.601
S3-1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S4·1 SWITCH KEYBOARD 12x12mm ALPS SKHC'AD (I<HC 10904) 43.601
S5·1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S6·1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S7·1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S8·1 SWITCH KI:YBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S9·1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S10-1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S11-1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601
S12·1 SWITCH KEYBOARD 12x12mm ALPS SKHCAD (KHC 10904) 43.601

INTERFACE MODULE RT2048 ECI AIS 4·6·25450L I 4·0·25450N 625450

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

VARIOUS SOCKET OIL 2x20 POLES 'AMP 641606·3 30.935

VARIOUS
VARIOUS
CONNECTION CABLE FOR
SOCKET
VOLUME CONTROL RT2048
1110' SIL 10 POLES
ECI A/S
PRECI·DIP . 3·0·25466
311·91-110
525466
78.803
C1·2 CAPACITOR MKT 150nF 5% 50VDC ERO MKT 1826·415106 4-G 11.181
C2-2 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2-35-V-100·M·T58 14.512
C3-2 CAPACITOR POLYPROPYLENE 2n2F 5% 1OOVDC 'ERO KP 1830-222101-4-GW 13.400
C4-2 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT-HM60 SK CH 180 J 15.060
C5·2 CAPACITOR CERAMIC 150pF 2% N150 100VDC PHILIPS 2222 689(679) 34151 15.148
C6·2 CAPACITOR CERAMIC 150pF 2% N150 100VDC PHILIPS 2222 689(679) 34151 15.148
C7·2 CAPACITOR CERAMIC 10nF -201+80% CL2 50VDC KCK RT-HE70 SK YF 103 Z 15.170
C8·2 CAPACITOR CERAMIC 10nF ·20/+80% CL2 50VDC KCK RT-HE70 SK YF 103 Z 15.170
C9·2 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK RT·HM60 SK VB 102 K 15.160
C10·2 CAPACITOR MKT 22nF 5% 1OOVDC PHILIPS 2222 370 89223 11.169
C11·2 CAPACITOR ELECTROLYTIC 220uF -201t50% 16VDC ELNA RJ2-16·V-221-M-T2 14.640

9724 PAGE 7-3

I
'
7 PARTS LIST RT2048
~

POSITION DESCRIPTION MANU FACTOR TYPE PART NO. l

~
C12·2 CAPACITOR ELECTROLYTIC 2m2F 20% 16VDG SAMHWA ELEC. SV-2200uF-16WV 14.713
C13·2 CAPACITOR MKT 470nF 5% 63VDC ERO MKT 1826·447/06 4-G 11.187
C14-2 CAPACITOR MKT 15nF 5% 63VDG PHILIPS 2222 370 89153 11.173 '
i
C15·2 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35·V·100·M·T58 14.512
C16·2 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2·35·V·100·M·T58 14.512 ~
C17·2 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
CAPACITOR MKT 220nF 5% 63VDC 2222 370 79224

~.
C18·2 PHILIPS 11.182
C19·2 CAPACITOR MKT 220nF 20°, 63VDC ERO MKT 1826-422/06 6-G 11.183
C20·2 CAPACITOR CERAMIC 10nF ·22' -30% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C21·2 CAPACITOR CERAMIC 470pF 10~o 500VOC KCK RT·HM60 SK YB 471 K 16.095
C22·2 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095 I
C23·2 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK RT·HM60 SK YB 102 K 15.160 I
C24·2 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK RT·HM60 SK YB 102 K 15.160 k~~ ~,

C25·2 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCI< RT·HM60 SK YB 102 K 15.160 'i.
C26·2 CAPACITOR CERAMIC 1OnF ·20/t80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C27·2
01·2
02·2
CAPACITOR POLYPROPYLENE
DIODE RECTIFIER
DIODE ZENER
1nOF 5% 100VDC
1N4002 100V/1A
4V7 2% 0.4W BZX7984V7
ERO
MOTOROLA
PHILIPS
KP 1830·210/01·4-GW
1N4002(03/04/05/06/07)RL
BZX79B4V7
13.398
25.100
26.496
L J'o?'
~\'r

03·2 DIODE LIGHT EMITIING REDSQUARE 5x5mm KINGBRIGHT L·15531DT 25.538

04·2
D5·2
06-2
DIODE LIGHT EMITIING
DIODE LIGHT EMITIING
DISPLAY ?SEGMENT LED
YELLOW SQUARE 5x5mm
REDSQUARE 5x5mm
HDSP-5551 RED
KINGBRIGHT
KINGBRIGHT
HP
L·1553 YDT
L·1553 lOT
HDSP·5551
25.539
25.538
25.725
L·
07·2 DISPLAY ?SEGMENT LED HDSP-5551 RED HP HDSP·5551 25.725
08·2
D9·2
010-2
DIODE
DIODE SCHOTTKY
DIODE ZENER
BAW62 HIGH SPEED
BAT 43
5.1 V 2% 0.4W BZX79B5V1
PHILIPS
THOMSON·CSF
PHILIPS
BAW62·143
BAT43
BZX79B5V1
25.350
27.600
26.497
)L (

J1-2 SOCKET 10 POLES F.RIBBON CABLE MOLE X 52011-1010 78.283

J2·2
J3-2
J4·2
SOCKET
SOCKET COAX 90 DEG.
SOCKET COAX 90 DEG.
7 POLES F.RIBBON CABLE
PCB VERSION
PCB VERSION
MOLEX
TAIKO
TAIKO
52011-0710
TMP·J01 X.Y6
TMP·J01X-V6
78.280
78.518
78.518
L
L1·2 FERRITE BEAD INDUCTOR DOUBLE BEAD CORE MURATA BL02RN2-R62T2 35.300
L2·2 FERRITE BEAD INDUCTOR DOUBLE BEAD CORE MURATA BL02RN2-R62T2 35.300
L3·2 CHOKE FIXED 120uH 10% FASTRON MICC-121 K-02 20.372
P1·2 MULTIPLUG 2x15 POLES PCB VERSION 3M 3531·6002/ 7630-6002 JL 78.253
P2·2 SIL SQUARE PINS 2 POLES CC=1/10' AMP 0·826629·2 78.322
(0-826647·2)
P3·2 SIL SQUARE PINS 2 POLES CC=1/10' AMP 0-826629-2 78.322
(0·826647·2)
Q1·2 TRANSISTOR AF BC328·25 PNP T0-92 PHILIPS BC328-25-126 28.052
02·2
Q3·2
Q4·2
Q5·2
TRANSISTOR AF
TRANSISTOR J FET
TRANSISTOR AF
TRANSISTOR AF
BC338·25 NPN T0-92
N CHANNEL BF245A
BC328·25 PNP T0-92
BC558B
PHILIPS
'PHILIPS
PHILIPS
PHILIPS
BC338·25·126
BF245A·126
BC328-25-126
BC558B-126
28.058
29.714
28.052
28.100
r·
Q6·2 TRANSISTOR AF BC548B NPN T0-92 PHILIPS BC548B·126 28.076 .!""'
Q7·2
Q8-2
R1·2
TRANSISTOR AF
TRANSISTOR AF
RESISTOR MF
BC548B NPN T0·92
BC548B NPN T0-92
22k OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
BC548B·126
BC548B-126
2322 181 53223
28.076
28.076 I
01.233
R2·2 RESISTOR MF 22k OHM 5% 0.33W PHILIPS 2322 187 73223 02.504
R3·2 RESISTOR MF 150 OHM 5% 0.4W PHILIPS 2322 181 53151
)!'"''
01.179
R4·2 RESISTOR OOHM 'PHILIPS 2322 181 90018 01.110 I
R6·2 RESISTOR MF 36k5 OHM 1% 0.6W PHILIPS 2322 156 13653 03.438
R7·2
R8·2
R9·2
R10·2
RESISTOR MF
RESISTOR MF
RESISTOR MF
POTENTIOMETER
2k7 OHM 5% 0.4W
1k5 OHM 5% 0.4W
75 OHM 5% 0.4W
50k OHM 20% 50mW LOG
PHILIPS
PHILIPS
PHILIPS
NOBLE
2322 181 53272
2322 181 53152
2322 181 53759
779·9013
01.210
01.204
01.171
08.286
r
R11·2
R12-2
R13·2
R14·2
R15·2
RESISTOR ARRAY
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
4x5k6 OHM 5% 1/4W
97k6 OHM 1% 0.6W
1k21 OHM 1% 0.6W
33k2 OHM 1% 0.6W
270k OHM 1% 0.6W
BOURNS
PHILIPS
PHILIPS
PHILIPS
PHILIPS
4608X·102·562
2322 156 19763
2322 15611212
2322 156 13323
2322 156 12704
08.626
03.471
03.227
03.232
03.465
r
R16·2 RESISTOR MF 4k32 OHM 1% 0.6W 'PHILIPS 2322 156 14322 03.415
R17·2 RESISTOR MF 120k OHM 5% 0.4W PHILIPS 2322 181 53124 01.252
R18·2 RESISTOR MF 91k OHM 5% 0.4W PHILIPS 2322 181 53913 01.248
R19·2 RESISTOR MF 330k OHM 1% 0.6W PHILIPS 2322 156 13304 03.270
R20-2 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R21-2 RESISTOR MF 150k OHM 5% 0.4W PHILIPS 2322 181 53154 01.254
R22·2 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R23·2 POTENTIOMETER 10k OHM 10% 0.1W LOG NOBLE V90·1 0155·D 08.257
R24·2 RESISTOR ARRAY 8x100k OHM 5% 1/SW BOURNS 4609X·101-104 08.655
R25·2 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R26·2 RESISTOR MF 51k0 OHM 1% 0.6W 'PHILIPS 2322 156 15103 03.462
R27·2 RESISTOR MF 270k OHM 1% 0.6W PHILIPS 2322 156 12704 03.465
R28-2 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615

9724
r!l
'
PAGE 7-4

r .
 7 PARTS LIST RT2048

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

R29·2 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615
R30·2 RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212

J R31·2
R32-2
R33·2
RESISTOR MF
RESISTOR MF
RESISTOR ARRAY
100k OHM 5% 0.4W
3k48 OHM 1% 0.6W
4x820 OHM 5% 0.25W
PHILIPS
PHILIPS
PANASONIC
2322 181 53104
2322 156 13482
EXBF8V821G (4X820R)
01.250
03.400
08.601
R34·2 RESISTOR ARRAY 4x820 OHM 5% 0.25W PANASONIC EXBF8V821G (4X820R) 08.601
R35·2 RESISTOR ARRAY 4x820 OHM 5% 0.25W PANASONIC EXBF8V821G (4X820R) 08.601
• R36·2 RESISTOR ARRAY 4x820 OHM 5% 0.25W PANASONIC EXBF8V821G (4X820R) 08.601
R38·2 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615
R39·2 RESISTOR MF 8k25 OHM 1% 0.6W 'PHILIPS 2322 156 18252 03.423
R40-2 RESISTOR MF 10k0 OHM 1% 0.6W PHILIPS 2322 15611003 03.427
R41·2 RESISTOR MF 15k0 OHM 1% 0.6W PHILIPS 2322 156 11503 03.429
R42·3 RESISTOR ARRAY 4x330 OHM 5% 1/4W BOURNS 4608X-102-331 08.608
R43-2 RESISTOR MF 47 OHM 5% 0.4W PHILIPS 2322 181 53479 01.166
R44-2 RESISTOR MF 1kO OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R45·2 RESISIOR MF 3k9 OHM 5% 0.4W PHILIPS 2322 181 53392 01.214
R46-2 RESISTOR MF 750 OHM 5% 0.4W PHILIPS 2322 181 53751 01.196
R47-2 RESISTOR MF 18k OHM 5% OAW PHILIPS 2322 181 53183 01.231
R48-2 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R49-2 RESISTOR MF 15k OHM 5% 0.4W PHILIPS 2322 181 53153 01.229
R50·2 RESISTOR MF 270k OHM 1% 0.6W PHILIPS 2322 156 12704 03.465
R54-2 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R55-2 RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212
R56·2 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R57·2 RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212
R58-2 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.250
R59·2 RESISTOR MF 5k1 1 OHM 1% 0.6W PHILIPS 2322 156 15112 03.414
R60·2 RESISTOR MF 357 OHM 1% 0.6W 'PHILIPS 2322 156 13571 02.204
U1-2 EEPROM 1k BIT SERIAL 93C46 NATIONAL NM93C46N 32.709
U2·2 EEPROM 1k BIT SERIAL 93C46 NATIONAL NM93C46N 32.709
U3-2 INTEGRATED CIRCUIT CPU PROGRAMMED (C1106) MOTOROLA SP .SPEC: C1106 32.563
ZC No: <427281 P>
U4-2 8 BIT SHIFT REG.SERIAL 10 74HC595 MOTOROLA MC74HC595P I MC74HC595AN 34.502
U5·2 8 BIT SHIFT REG.SERIAL 10 74HC595 MOTOROLA MC74HC595P I MC74HC595AN 34.502
U6·2 8 BIT SHIFT REG.SERIAL 10 74HC595 MOTOROLA MC74HC595P I MC74HC595AN 34.502
U7-2 QUAD VOLTAGE COMPERATOR LM339 NATIONAL LM339N 31.075
U8-2 QUAD OP.AMP. 324 NATISGS LM324N 31.065
U9·2 VOLTAGE REG. ADJUSTABLE lo,0.1A LM317L MOTOROLA LM317LZ RA 31.145

SYNTESE MODULE RT2048 ECI A/S 5-0-25451 H I 4-0-25451 P 625451

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

NORTON NORMOUNT V1300 0.8x12mm 95.512

C1·3 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 78104 11.136
C2·3 CAPACITOR MKT 220nF 10% 63VDC PHILIPS 2222 370 78224 11.095
C3-3 CAPACITOR POLYSTYRENE 56pF 1% 630V IIPHILIPS 2222 431 85609 10.394
C4-3 CAPACITOR POLYSTYRENE 300pF 1% 630VDC PHILIPS 2222 431 83001 10.414
C5·3 CAPACITOR ELECTROLYTIC 1OOuF -1 0/+50% 25VDC ERO EKM 00 CC 310 E G5 14.610
C6·3 CAPACITOR POLYSTYRENE 51pF 1% 630V IIPHILIPS 2222 431 85109 10.393
C7·3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C8·3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C9·3 CAPACITOR MKT 22nF 10% 1OOVDC PHILIPS 2222 370 88223 11.175
C10-3 CAPACITOR MKT 220nF 10% 63VDC PHILIPS 2222 370 78224 11.095
C11-3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C12·3 CAPACITOR ELECTROLYTIC 47uF 20% 25VDC ELNA RJ2-25·V-470-M-F1 14.524
C13·3 CAPACITOR MKT 220nF 5% 63VDC PHILIPS 2222 370 79224 11.182
C14-3 CAPACITOR ELECTROLYTIC 22uF 20% 35VDC ELNA RJ2-35·V·220-M-F1 14.516
C15·3 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35-V-100-M-T34(T58) 14.512
C16·3 CAPACITOR ELECTROLYTIC 4.7uF 20% 50VDC ELNA RJ2-50-V-4R7·M·T34 14.510
C17·3 CAPACITOR MKT 1u5F 10% 50VDC ERO MKT 1826 515105 5-G 11.191
C18-3 CAPACITOR POLYSTYRENE 12n1F 1% 63VDC 'PHILIPS 2222 443 41213 10.796
C19-3 CAPACITOR ELECTROLYTIC 1uF 20% 50VDC ELNA RJ2-50· V-01 0-M·T34 14.506
C20·3 CAPACITOR CERAMIC 39pF 5% NPO 50VDC KCK RT-HE50 SK CH 390 J 15.085
C21-3 CAPACITOR CERAMIC 5p6F +l-0.25pF NPO 500VDC KCK RT-HM60 SK CH 5R6 C 15.015
C22-3 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK RT·HM60 SK YB 102 K 15.160
C23-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C24·3 CAPACITOR CERAMIC 6p8F +l-0.25pF NPO 100VDC PHILIPS 2222 689 09688 15.325
C25-3 CAPACITOR CERAMIC 1n0F 10% CL2 SOOVDC KCK RT-HM60 SK YB 102 K 15.160
C26-3 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK AT-HM60 SK YB 102 K 15.160
C27·3 CAPACITOR CERAMIC 1n0F 10% CL2 500VDC KCK RT-HM60 SK YB 102 K 15.160
9724 PAGE 7-5

I
!
7 PARTS LIST RT2048

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

C26·3 CAPACITOR CERAMIC 1OnF ·20it80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C29·3 CAPACITOR MKT 1uF 5% 63VDC ERO MKT 1626·510106 4-G 11.190
C30·3 CAPACITOR MKT 470nF 5% 63VDC ERO MKT 1826-447106 4·G 11.167
C31·3 CAPACITOR MKT 22nF 5% 100VDC PHILIPS 2222 370 89223 11.169
C32·3 CAPACITOR ELECTROLYTIC 47uF 20% 25VDC ELNA RJ2·25-V-470·M·F1 14.524
C33·3 CAPACITOR CERAMIC 100pF 5% NPO 50VDC KCK RT·HE80 SJ< CH 101 J 15.136
C34·3 CAPACITOR POLYSTYRENE 825pF 1% 63VDC PHILIPS 2222 443 48251 10.755
C35·3 CAPACITOR MKT 150nF 5% 50VDC ERO MKT 1826·415106 4-G 11.181
C36·3 CAPACITOR MKT 68nF 5% 63VDC PHILIPS 2222 370 79683 11.178
C37·3 CAPACITOR MKT 1uF 10% 63VDC ERO MKT 1626·510106 5-G 11.137
C36·3 CAPACITOR POLYSTYRENE 12n1F 1% 63VDC 'PHILIPS 2222 443 41213 10.796
C39·3 CAPACITOR POLYSTYRENE 221pF 1% 63VDC PHILIPS 2222 443 42211 10.727
C41-3 CAPACITOR ELECTROLYTIC 47uF 20% 25VDC ELNA RJ2·25-V-470-M-F1 14.524
C42·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C43·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCJ< RT·HM60 SK YB 471 K 16.095
C44·3 CAPACITOR ELECTROLYTIC 100uF ·101+50% 25VDC ERO EKM 00 CC 310 E G5 14.610
C45·3 CAPACITOR MKT 330nF 5% 63VDC ERO MKT 1826·433/06 4·G 11.104
C46·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C47·3 CAPACITOR CERAMIC 15pF 5% N150 500VDC KCJ< RT ·HM60 SK PH 150 J 16.115
C48·3
C49·3
CS0-3
CAPACITOR CERAMIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
22pF 5% N150 500VDC
13pF 5% N150 SOVDC
470pF 10% SOOVDC
KCK
KCK
KCK
RT-HM SK PH 220 J
RT·HE40 SK PH 130 J
RT·HM60 SK YB 471 K
15.062
15.051
16.095
L
C51·3 CAPACITOR CERAMIC 2p7F t/·0.25pF N150 50VDC KCK RT·HE40 SK PJ 2R7 C 15.001
C52·3 CAPACITOR CERAMIC 18pF 5% NPO 500VDC J<CJ( RT-HM60 SK CH 180 J 15.060
C53-3 CAPACITOR CERAMIC 18pf 5% NPO 500VDC KCJ< RT·HM60 SK CH 180 J 15.060
C54·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCJ< RT·HM60 SK YB 411 K 16.095
C55·3 CAPACITOR CERAMIC 12pF 5% NPO 500VDC KCJ< RT·HM60-SK CH 120 J 15.575
C56·3 CAPACITOR CERAMIC 8p2F t·0.25pF NPO 500VDC KCK RT·HM60 SK 8R2 C 15.030
C57·3 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT·HM60 SK CH 180 J 15.060
C58·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C59·3 CAPACITOR CERAMIC 18pF 2% NPO 100VDC PHILIPS 2222 689 10189 15.330
C60-3 CAPACITOR CERAMIC 470pf 10% 500VDC KCJ< RT·HM60 SJ< VB 471 K 16.095
C61·3 CAPACITOR CERAMIC 12pF 2% NPO 100VDC PHILIPS 2222 689 10129 15.328
C62·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK VB 471 K 16.095
C63·3 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35·V·1 OO·M·T34(T58) 14.512
C64·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C65·3 CAPACITOR CERAMIC 470pF 10% 500VDC J<CK RT·HM60 SK YB 471 K 16.095
C66·3 CAPACITOR CERAMIC 15pF 2% NPO 100VDC PHILIPS 2222 689 10159 15.329
C67·3 CAPACITOR CERAMIC 15pF 2% NPO 100VDC PHILIPS 2222 609 10159 15.329
C68·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C69-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C70·3 CAPACITOR CERAMIC 12pF 2% NPO 100VDC PHILIPS 2222 689 10129 15.328
C71·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K ~ 16.095
C72·3 CAPACITOR CERAMIC 10nF -20/t80% CL2 50VDC KCJ< RT·HE70 SK YF 103 Z 15.170
C73·3 CAPACITOR CERAMIC 33pF 2% NPO 100VDC PHILIPS 2222 689 10339 15.333
C74·3 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35·V·1 OO·M·T34(T58) 14.512
C75·3 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2·35·V ·100-M·T34(T58) 14.512
C76·3 CAPACITOR ELECTROLYTIC 220uF ·20/t50% 16VDC ELNA RJ2·16·V·221·M·T2 14.640
C77-3 CAPACITOR TRIMMING 3.9-27pF PTFE DAU 107.3901.027 17.110
C78·3 CAPACITOR TRIMMING 1.8-9pF PTFE DAU 117 1991 009 B021 17.090
C79-3 CAPACITOR MKT 220nF 10% 63VDC PHILIPS 2222 370 78224 11.095
CB0-3 CAPACITOR MKT 0.1 uF 10% 63VDC PHILIPS 2222 370 78104 11.136
D1·3 DIODE BAW62 HIGH SPEED PHILIPS BAW62·143 25.350
D2·3 DIODE 1N4150 PHILIPS 1N4150 25.140
D3·3 DIODE SCHOTIKY BAT 43 THOMSON·CSF BAT43 27.600
D4·3 DIODE BAW62 HIGH SPEED PHILIPS BAW62-143 25.350
D5·3 DIODE 1N4148 HIGH SPEED PHILIPS 1N4146·143 25.131
D6·3 DIODE SWITCH FACTORY SELECTED MPN 3700 ECI AIS C1 OB2A I 0-0·25550 725550
D7·3 DIODE SWITCH BA282 TFK BA 282 TAPED 25.390
D8·3 DIODE SWITCH BA262 TFK BA 282 TAPED 25.390
D9·3 DIODE CAPASITANCE 13pFI9VDC TOSHIBA 1SV1 01 in matched group 26.135
D10·3 DIODE SCHOTIKY BAT 43 THOMSON-CSF BAT43 27.600
J1·3 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP·J01X-A2 78.517
J2·3 SOCKET COAX FOR PCB 45 DEG, HORIZONTAL TAIKO TMP·J01X·A2 78.517
J3·3 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP-J01X-A2 78.517
J4-3 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP-J01X·A2 78.517
L1·3 CHOKE 0.10uH 5% WEST CAP 1A1003M·5% I TAPED 20.099
L3·3 CHOKE 4u7H 10% SIEMENS B78108-T1472·K 20.137
L4·3 CHOKE 4u7H 10% SIEMENS B78108-T1472-K 20.137
L5·3 CHOKE 4u7H 10% SIEMENS B78108-T1472-K 20.137
L6·3 CHOKE 0.10uH 5% WEST CAP 1A1003M·5% I TAPED 20.099
L7-3 CHOKE 0.10uH 5% WEST CAP 1A1003M·5% I TAPED 20.099
L6·3 CHOKE 0.10uH 5% WEST CAP 1A1003M-5% I TAPED 20.099

9724
PAGE 7-6
.J
'' .,_/
7 PARTS LIST RT2048

i
I
,~·,-..,
POSITION

L9·3
DESCRIPTION

TRANSFORMER RF 110nH ADJUSTABLE

MANUFACTOR

TOKO
TYPE

E526·11 0436
PART NO.

38.407
P1·3 PLUG PCB 2x5 POLES RIGHT ANGLE 3M 7610·5002-JL 78.252

J
-""~'1
01·3
02·3
03·3
TRANSISTOR
TRANSISTOR RF
TRANSISTOR RF SWITCH
BF 506
BF199
2N2369A
SIEMENS
PHILIPS
MOTOROLA
BF506·E6327
BF199
2N2369A
28.202
28.178
28.315
04·3 TRANSISTOR AF BC548B NPN T0-92 PHILIPS BC548B 28.076

[J
...,~:·
05·3
06·3
07·3
TRANSISTOR AF
TRANSISTOR AF
TRANSISTOR RF
BC558B
BC338·25 NPN T0-92
LOW POWER PNP BF979
PHILIPS
PHILIPS
TELEFUNKEN AG
BC558B
BC338·25
BF979
28.100
28.058
28.251
08·3 TRANSISTOR AF BC558B PHILIPS BC558B 28.100

j
'I·'"'
.
09·3
010·3
011·3
012·3
TRANSISTOR AF
TRANSISTOR
TRANSISTOR
TRANSISTOR AF
BC548B NPN T0-92
BC549C
BC549C
BC548B NPN T0-92
PHILIPS
PHILIPS'
PHILIPS'
PHILIPS
BC548B
BC549C
BC549C
BC548B
28.076
28.082
28.082
28.076
013·3 TRANSISTOR 2N4427 MOTOROLA' 2N4427 28.330

J'
014·3 TRANSISTOR RF BFW92A TFK BFW92A 29.160
015·3 TRANSISTOR RF LOW POWER PNP BF979 TELEFUNKEN AG BF979 28.251
'") 016-3 TRANSISTOR RF BFW92A TFK BFW92A 29.160

'j 017·3
018·3
R1·3
TRANSISTOR J FET
TRANSISTOR JFET
RESISTOR MF
N CHANNEL BF245A
N-CHAN. J309
20k0 OHM 1% 0.6W
'MOTOROLA
'SILICONIX
'PHILIPS
BF245A
J309
2322 156 12003
29.714
29.724
03.452
R2-3 RESISTOR MF 60k4 OHM 1% 0.6W PHILIPS 2322 156 16043 03.238

J R3·3
R4·3
R5·3
R6·3
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
33k2 OHM 1% 0.6W
100k OHM 1% 0.6W
221 k OHM 1% 0.6W
47k OHM 5% 0.4W
'PHILIPS
'PHILIPS
'PHILIPS
PHILIPS
2322 15613323
232215611004
2322156 12214
2322 181 53473
03.232
03.477
03.483
01.241
R7·3 RESISTOR MF 6k8 OHM 5% 0.4W PHILIPS 2322 181 53682 01.220
R8·3 RESISTOR MF 220 OHM 5% 0.4W PHILIPS 2322 181 53221 01.183
R9·3 RESISTOR MF 33 OHM 5% 0.4W PHILIPS 2322 181 53339 01.162
R10·3 RESISTOR MF 82 OHM 5% 0.4W PHILIPS 2322 181 53829 01.172
R11·3 RESISTOR MF 12k OHM 5% 0.4W PHILIPS 2322181 53123 01.227
l iJ
t::t R12·3 RESISTOR MF 18k OHM 5% 0.4W PHILIPS 2322181 53183 01.231
~0 R13·3 RESISTOR MF 51 OHM 5% 0.4W PHILIPS 2322181 53519 01.167
R14·3 RESISTOR MF 12k OHM 5% 0.4W PHILIPS 2322 181 53123 01.227
R15·3 RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212
R16·3 RESISTOR MF 2k0 OHM 5% 0.4W PHILIPS 2322 181 53202 01.207
R17·3 RESISTOR MF 1k5 OHM 5% 0.4W PHILIPS 2322181 53152 01.204
R18·3 RESISTOR MF 18k OHM 5% 0.4W PHILIPS 2322 181 53183 01.231
R19·3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R20-3 RESISTOR MF 5k6 OHM 5% 0.4W PHILIPS 2322 181 53562 01.218
R21·3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R22·3 RESISTOR MF 1k5 OHM 5% 0.4W PHILIPS 2322 181 53152 01.204
R23·3 RESISTOR MF 1k3 OHM 1% 0.6W PHILIPS 23221'156 11302 03.402
R24·3 RESISTOR MF 1k3 OHM 1% o.aw PHILIPS 232215611302 03.402
R25-3 RESISTOR MF 220 OHM 5% 0.4W PHILIPS 2322 181 53221 01.183
R26·3 RESISTOR MF 120 OHM 5% OAW PHILIPS 2322 181 53121 01.177
R27·3 RESISTOR MF 60k4 OHM 1% o.aw PHILIPS 2322 156 16043 03.238
R28·3 RESISTOR MF 60k4 OHM 1% 0.6W PHILIPS 2322 156 16043 03.238
R29·3 RESISTOR MF 100k OHM 5% OAW PHILIPS 2322181 53104 01.250
R30·3 RESISTOR MF 30k OHM 5% 0.4W PHILIPS 2322 181 53303 01.236
R31·3 RESISTOR MF 56 OHM 5% 0.4W PHILIPS 2322 181 53569 01.168
R33·3 RESISTOR MF 30k OHM 5% 0.4W PHILIPS 2322 181 53303 01.236
R34·3 RESISTOR MF 1MO OHM 5% 0.4W PHILIPS 2322 181 53105 01.275
R35·3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R36·3 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R37·3 RESISTOR MF 110k OHM 5% 0.4W PHILIPS 2322 181 53114 01.251
R38·3 RESISTOR MF 33 OHM 5% OAW PHILIPS 2322 181 53339 01.162
R39·3 RESISTOR MF 270k OHM 5% 0.4W PHILIPS 2322 181 53274 01.260
R40·3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R41·3 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R42·3 RESISTOR MF 270k OHM 5% 0.4W PHILIPS 2322 181 53274 01.260
R43·3 RESISTOR MF 430 OHM 5% 0.4W 'PHILIPS 2322 181 53431 01.190
R44·3 RESISTOR MF 8k2 OHM 5% 0.4W PHILIPS 2322 181 53822 01.222
R45·3 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R46·3 RESISTOR MF 1k2 OHM 5% OAW PHILIPS 2322 181 53122 01.202
R47·3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R48·3 RESISTOR MF 82 OHM 5% 0.4W PHILIPS 2322 181 53829 01.172
R49·3 RESISTOR MF 2k43 OHM 1% 0.6W 'PHILIPS 2322 156 12432 03.396
R50·3 RESISTOR MF 56k OHM 5% OAW PHILIPS 2322 181 53563 01.243
R51·3 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R52·3 RESISTOR MF 221 OHM 1% 0.6W 'PHILIPS 2322 156 12211 03.384
R53·3 RESISTOR MF 5k11 OHM 1%0.6W PHILIPS 2322156 15112 03.414
R54·3 RESISTOR MF 39k2 OHM 1% 0.6W PHILIPS 2322 156 13923 03.439

9724 PAGE7-7

II
 ~
7 PARTS LIST RT2048

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

~
R55·3 RESISTOR MF 39k2 OHM 1% 0.6W PHILIPS 2322 156 13923 03.439 (
R56·3 RESISTOR MF 6k19 OHM 1% 0.6W 'PHILIPS 2322 15616192 03.399
R57·3 RESISTOR MF 10k0 OHM 1% 0.6W PHILIPS 2322 156 11003 03.427
R58·3 RESISTOR MF 360k OHM 5% 0.4W PHILIPS 2322 181 53364 01.263 ~
R59·3 RESISTOR MF 8k2 OHM 5% 0.4W PHILIPS 2322 181 53822 01.222
(
R60·3 RESISTOR MF 8k2 OHM 5% 0.4W PHILIPS 2322 181 53822 01.222
R61·3 RESISTOR MF 5k11 OHM 1% 0.6W PHILIPS 2322 156 15112 03.414
;
R62·3 RESISTOR MF 174k OHM 1% 0.6W PHILIPS 2322 156 11744 03.255
PHILIPS 2322181 53751 01.196
llkil
R63·3 RESISTOR MF 750 OHM 5% 0.4W
R65·3 RESISTOR MF 150 OHM 5% 0.4W PHILIPS 2322 181 53151 01.179
R66-3 RESISTOR MF 47 OHM 5% 0.4W PHILIPS 2322 181 53479 01.166
R67·3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R68-3 RESISTOR MF 560 OHM 5% 0.4W PHILIPS 2322 181 53561 01.193
R69·3 RESISTOR MF 120 OHM 5% 0.4W PHILIPS 2322 181 53121 01.177
R70·3 RESISTOR MF 15 OHM 5% 0.4W PHILIPS 2322 181 53159 01.154
R71·3 RESISTOR MF 3R9 OHM 5% 0.4W PHILIPS 2322 181 53398 01.139
~.'.:.~}
R72·3 RESISTOR MF 2k2 OHM 5% 0.4W PHILIPS 2322 181 53222 01.208
~~;
R73·3 RESISTOR MF 100 OHM 5% 0.4W PHILIPS 2322 181 53101 01.175
R74-3 RESISTOR MF 270 OHM 5% 0.4W PHILIPS 2322 181 53271 01.185 '
R75·3 RESISTOR MF 12 OHM 5% 0.4W PHILIPS 2322 181 53129 01.152
R76·3 RESISTOR MF 27 OHM 5% 0.4W PHILIPS 2322 181 53279 01.160
R77·3 RESISTOR MF 2k7 OHM 5% 0.4W PHILIPS 2322 181 53272 01.210
R78-3 RESISTOR MF 91 OHM 5% 0.4W PHILIPS 2322181 53919 01.174
R79·3 RESISTOR MF 47 OHM 5% 0.4W PHILIPS 2322 181 53479 01.166
01.205
\;
R80·3 RESISTOR MF 1k6 OHM 5% 0.4W PHILIPS 2322181 53162 '~o. ....."

R81-3 RESISTOR MF 4.3k OHM 5% 0.4W 'PHILIPS 2322 181 53432 01.215
R82·3 RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212
R83·3 RESISTOR MF 560 OHM 5% 0.4W PHILIPS 2322 181 53561 01.193
R84-3 RESISTOR MF 300 OHM 5% 0.4W PHILIPS 2322 181 53301 01.186 L
R85·3 RESISTOR MF 100 OHM 5% 0.4W PHILIPS 2322 181 53101 01.175
R86-3 RESISTOR MF 300 OHM 5% 0.4W ·PHILIPS 2322 181 53301 01.186
R87-3 RESISTOR MF 18 OHM 5% 0.4W PHILIPS 2322 181 53189 01.156
R88·3 RESISTOR MF 56 OHM 5% 0.4W PHILIPS 2322 181 53569 01.168
R89·3 RESISTOR MF 5k1 OHM 5% 0.4W PHILIPS 2322 181 53512 01.217
R90·3 RESISTOR MF 75 OHM 5% 0.4W PHILIPS 2322 181 53759 01.171
R91-3 RESISTOR MF 1k8 OHM 5% 0.4W PHILIPS 2322 181 53182 01.206
R92·3 RESISTOR MF 68 OHM 5% 0.4W PHILIPS 2322 181 53689 01.170
R93-3 RESISTOR MF 8R2 OHM 5% 0.4W PHILIPS 2322 181 53828 01.147
R94·3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R95·3 PRESET CERMET 250k OHM 10% 0.5W 'BOURNS 3386P-1-254 07.895
R96·3 PRESET CERMET 2k0 OHM 5% 0.5W BOURNS 3386P-1-202-11 07.887
R97-3 PRESET CERMET 250k OHM 10% 0.5W 'BOURNS 3386P-1·254 07.895
R98·3 PRESET CERMET 1k0 OHM 10% 0.5W BOURNS 3386P·1-102 f· 07.886
U1·3 QUAD OP.AMP. 324 NAT/SGS LM324N 31.065
U2-3 DUAL O-FF POS TRIG. 74HC74 TEXAS SN74HC74N 34.501
U3-3 SERIAL INPUT PLL SYNTHES. MC145158P2 MOTOROLA MC145158P2 33.492
U4-3
X1·3
L2-3
L10·3
INTEGRATED CIRCUIT
CRYSTAL C1074
COIL
CHOKE TL489
MC12015P
14.850MHz 10ppm NC18C
TL371
MOTOROLA'
NDK
ECI NSIO
ECINS
MC12015P
SP.SPEC: C1074
6-0-23687
6-0-25459
32.850
39.839
400371
400489
) r~
'

L11·3 CHOKE TL491 ECINS 6-0-25461 400491

L12-3
L13-3
CHOKE TL491
CHOKE TL489
ECINS
ECINS
6·0-25461
6·0·25459
400491
400489 f"'~i
L14-3 CHOKE TL490 ECINS 6·0-25460 400490

SYNTESE MODULE (USA) RT2048 ECI AIS 5·0·25451 H /4·0·25451 P 625551 r~~

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

NORTON NORMOUNT V1300 0.8x12mm 95.512

C1-3 CAPACITOR MKT 0.1 uF 10% 63VDC PHILIPS 2222 370 78104 11.136
C2·3 CAPACITOR MKT 220nF 10% 63VOC PHILIPS 2222 370 78224 11.095
C3-3 CAPACITOR POLYSTYRENE 56pF 1% 630V #PHILIPS 2222 431 85609 10.394
C4-3 CAPACITOR POLYSTYRENE 300pF 1% 630VDC PHILIPS 2222 431 83001 10.414
C5-3 CAPACITOR ELECTROLYTIC 100uF -10/+50% 25VDC ERO EKM 00 CC 310 E G5 14.610
C6·3 CAPACITOR POLYSTYRENE 51pF 1% 630V #PHILIPS 2222 431 85109 10.393
C7-3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C8-3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C9-3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
C10-3 CAPACITOR MKT 220nF 10% 63VDC PHILIPS 2222 370 78224 11.095
C11-3 CAPACITOR MKT 22nF 10% 100VDC PHILIPS 2222 370 88223 11.175
~1
\
9724
PAGE 7-8

~
J 7 PARTS LIST RT2048

J
/''
'
POSITION

C12-3
DESCRIPTION

CAPACITOR ELECTROLYTIC 47uF 20% 25VDC

MANUFACTOR

ELNA
TYPE

RJ2-25-V-470·M·F1
PART NO.

14.524
C13-3 CAPACITOR MKT 220nF 5% 63VDC PHILIPS 2222 370 79224 11.182

J
... '\
0
C14-3
C15-3
C16-3
CAPACITOR ELECTROLYTIC
CAPACITOR ELECTROLYTIC
CAPACITOR ELECTROLYTIC
22uF 20% 35VDC
10uF 20% 35VDC
4.7uF 20% 50VDC
ELNA
ELNA
ELNA
RJ2-35·V·220·M·F1
RJ2-35-V-1 OO-M-T34(T58)
RJ2-50·V·4R7-M-T34
14.516
14.512
14.510
C17-3 CAPACITOR MKT 1u5F 10% 50VDC ERO MKT 1826 515/05 5-G 11.191

,J C18-3
C19-3
C20·3
C21-3
CAPACITOR POLYSTYRENE
CAPACITOR ELECTROLYTIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
12n1F 1% 63VDC
1uF 20% 50VDC
39pF 5% NPO 50VDC
5p6F t/·0.25pF NPO 500VDC
'PHILIPS
ELNA
KCK
KCK
2222 443 41213
RJ2-50·V-01 0-M· T34
RT·HE50 SK CH 390 J
RT-HM60 SK CH 5R6 C
10.796
14.506
15.085
15.015

I
C22-3 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KCK RT-HM60 SK VB 102 K 15.160
C23-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
"~ ~

(.t C24-3 CAPACITOR CERAMIC 6p8F t/·0.25pF NPO 1OOVDC PHILIPS 2222 689 09688 15.325
;}:'
C25-3 CAPACITOR CERAMIC 1n0F 10% CL2 500VDC KCK RT-HM60 SK YB 102 K 15.160
C26-3 CAPACITOR CERAMIC 1n0F 10% CL2 500VDC KCK RT-HM60 SK YB 102 K 15.160

wl ~ C27-3
C28-3
CAPACITOR CERAMIC
CAPACITOR CERAMIC
1nOF 10% CL2 500VDC
1OnF -20/t80% CL2 50VDC
KCK
KCK
RT-HM60 SK YB 102 K
RT-HE70 SK YF 103 Z
15.160
15.170
C29·3 CAPACITOR MKT 1uF 5% 63VDC ERO MKT 1826·510/06 4-G 11.190
C30-3 CAPACITOR MKT 470nF 5% 63VDC ERO MKT 1826-447/06 4-G 11.187
C31-3 CAPACITOR MKT 22nF 5% 100VDC PHILIPS 2222 370 89223 11.169
C32·3 CAPACITOR ELECTROLYTIC 47uF 20% 25VDC ELNA RJ2-25-V·470-M·F1 14.524
C33·3 CAPACITOR CERAMIC 1OOpF 5% NPO 50VDC KCK RT ·HE80 SK CH 101 J 15.136

]
C34-3 CAPACITOR POLYSTYRENE 825pF 1% 63VDC PHILIPS 2222 443 48251 10.755
C35-3 CAPACITOR MKT 150nF 5% 50VDC ERO MKT 1826·415/06 4-G 11.181
C36·3 CAPACITOR MKT 68nF 5% 63VDC PHILIPS 2222 370 79683 11.178
C37-3 CAPACITOR MKT 1uF 10% 63VDC ERO MKT 1826-510/06 5-G 11.137
C38-3 CAPACITOR POLYSTYRENE 12n1F 1% 63VDC 'PHILIPS 2222 443 41213 10.796

,I C39-3 CAPACITOR POLYSTYRENE 221pF 1% 63VDC PHILIPS 2222 443 42211 10.727
!
J C41·3 CAPACITOR ELECTROLYTIC 47uF 20% 25VDC ELNA RJ2-25·V-470·M-F1 14.524
C42·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C43-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C44-3 CAPACITOR ELECTROLYTIC 1OOuF -1 O/t50% 25VDC ERO EKM 00 CC 310 E G5 14.610
I~ C45·3
C46-3
CAPACITOR MKT
CAPACITOR CERAMIC
330nF 5% 63VDC
470pF 10% 500VDC
ERO
KCK
MKT 1826-433/06 4-G
RT·HM60 SK VB 471 K
11.184
16.095
C47·3 CAPACITOR CERAMIC 15pF 5% N150 500VDC KCK RT-HM60 SK PH 150 J 16.115
C48·3 CAPACIIOR CERAMIC 22pF 5% N150 500VDC KCK RT·HM SK PH 220 J 15.062
C49·3 CAPACITOR CERAMIC 13pF 5% N150 50VDC KCK RT-HE40 SK PH 130 J 15.051
C50-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C51-3 CAPACITOR CERAMIC 2p7F t/·0.25pF N150 50VDC KCK RT ·HE40 SK PJ 2R7 C 15.001
C52·3 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT·HM60 SK CH 180 J 15.060
C53·3 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT·HM60 SK CH 180 J 15.060
C54-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK VB 471 K 16.095
C55-3 CAPACITOR CERAMIC 12pF 5% NPO 500VDC KCK RT+jM60·SK CH 120 J 15.575
C56·3 CAPACITOR CERAMIC 8p2F +·0.25pF NPO 500VDC KCK RT·HM60 SK 8R2 C 15.030
C57-3 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT·HM60 SK CH 180 J 15.060
C58·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C59·3 CAPACITOR CERAMIC 18pF 2% NPO 100VDC PHILIPS 2222 689 10189 15.330
C60-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C61-3 CAPACITOR CERAMIC 12pF 2% NPO 100VDC PHILIPS 2222 689 10129 15.328
C62-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK VB 471 K 16.095
C63·3 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2-35-V-1 00-M-T34(T58) 14.512
C64·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C65·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C66-3 CAPACITOR CERAMIC 15pF 2% NPO 100VDC PHILIPS 2222 689 10159 15.329
C67-3 CAPACITOR CERAMIC 15pF 2% NPO 100VDC PHILIPS 2222 689 10159 15.329
C68-3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C69·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C70-3 CAPACITOR CERAMIC 12pF 2% NPO 100VDC PHILIPS 2222 689 10129 15.328
C71·3 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C72-3 CAPACITOR CERAMIC 1OnF -20/tBO% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C73-3 CAPACITOR CERAMIC 33pF 2'/o NPO 100VDC PHILIPS 2222 689 10339 15.333
C74-3 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2-35-V-1 00-M-T34(T58) 14.512
C75-3 CAPACITOR ELECTROLYTIC 10uF 20% 35VDC ELNA RJ2-35· V-1 00-M· T34(T58) 14.512
C76-3 CAPACITOR ELECTROLYTIC 220uF ·20/+50% 16VDC ELNA RJ2-16-V-221-M-T2 14.640
C77-3 CAPACITOR TRIMMING 3.9-27pF PTFE DAU 107.3901.027 17.110
C78·3 CAPACITOR TRIMMING 1.8-9pF PTFE DAU 117 1991 009 B021 17.090
C79-3 CAPACITOR MKT 220nF 10% 63VDC PHILIPS 2222 370 78224 11.095
C80-3 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 78104 11.136
D1-3 DIODE BAW62 HIGH SPEED PHILIPS BAW62-143 25.350
D2-3 DIODE 1N4150 PHILIPS 1N4150 25.140
D3-3 DIODE SCHOTTKY BAT 43 THOMSON-CSF BAT43 27.600
D4·3 DIODE BAW62 HIGH SPEED PHILIPS BAW62-143 25.350
D5·3 DIODE 1N4148 HIGH SPEED PHILIPS 1N4148-143 25.131

9724 PAGE 7-9

I I
 ~
7 PARTS LIST RT2048
I
POSITION DESCRIPTION MANUFACTOR TYPE PART NO. 9724
~
D6-3 DIODE SWITCH FACTORY SELECTED MPN 3700 ECINS C1082A I 0-0-25550 725550 I

07-3 DIODE SWITCH BA282 TFK BA282 TAPED 25.390

D8-3 DIODE SWITCH BA282 TFK BA282 TAPED 25.390
D9·3 DIODE CAPASITANCE 13pFI9VDC TOSHIBA 1SV101 in matched group 26.135
D10-3 DIODE SCHOTIKY BAT 43 THOMSON-CSF BAT43 27.600
J1-3 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP-J01X-A2 78.517
J2-3
J3-3
SOCKET COAX FOR PCB
SOCKET COAX FOR PCB
45 DEG. HORIZONTAL
45 DEG. HORIZONTAL
TAIKO
TAIKO
TMP-J01X·A2
TMP-J01X-A2
78.517
78.517 !~·
J4-3 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP-J01X-A2 78.517 '<,

L1-3 CHOKE 0.10uH 5% WEST CAP 1A1003M-5% I TAPED 20.099

L2-3 COIL TL371 ECINSIO 6-0-23687 400371 I
L3-3
L4-3
CHOKE 4u7H 10% SIEMENS B78108-T1472-K 20.137 IfiN~
CHOKE 4u7H 10% SIEMENS B78108-T1472-K 20.137 ([
~ ';
L5-3 CHOKE 4u7H 10% SIEMENS B78108-T1472-K 20.137
L6-3 CHOKE 0.10uH 5% WEST CAP 1A1003M-5% I TAPED 20.099
II
L7·3 CHOKE 0.10UH 5% WEST CAP 1A1003M-5% I TAPED 20.099
L8-3 CHOKE 0.10uH 5% WEST CAP 1A1003M-5% I TAPED 20.099 k"''
L9-3 TRANSFORMER RF 110nH ADJUSTABLE TOKO E526· 110436 38.407 (
l10-3 CHOKE TL489 ECINS 6-0-25459 400489
L11-3
L12-3
L13-3
CHOKE TL491
CHOKE TL491
CHOKE TL489
ECINS
ECINS
ECINS
6-0-25461
6-0-25461
6-0·25459
400491
400491
400489
L
L14-3 CHOKE TL490 ECINS 6·0·25460 400490
P1·3
01-3
02-3
PLUG PCB
TRANSISTOR
TRANSISTOR RF
2x5 POLES RIGHT ANGLE
BF 506
BF199
3M
SIEMENS
PHILIPS
761 0-5002-JL
BF506·E6327
BF199
78.252
28.202
28.178
\L
03-3 TRANSISTOR RF SWITCH 2N2369A MOTOROLA 2N2369A 28.315
04-3 TRANSISTOR AF BC548B NPN T0-92 PHILIPS BC548B 28.076
05-3
06-3
TRANSISTOR AF
TRANSISTOR AF
BC558B
BC338-25 NPN T0-92
PHILIPS
PHILIPS
BC558B
BC338-25
28.100
28.058
L
07-3 TRANSISTOR RF LOW POWER PNP BF979 TELEFUNKEN AG BF979 28.251
08-3 TRANSISTOR AF BC558B PHILIPS BC558B 28.100
09-3 TRANSISTOR AF BC548B NPN T0-92 PHILIPS BC548B 28.076
010·3 TRANSISTOR BC549C PHILIPS' BC549C 28.082
011-3 TRANSISTOR BC549C PHILIPS' BC549C 28.082
012-3 TRANSISTOR AF BC548B NPN T0-92 PHILIPS BC548B 28.076
013-3 TRANSISTOR 2N4427 MOTOROLA' 2N4427 28.330
014-3 TRANSISTOR RF BFW92A TFK BFW92A 29.160
015-3 TRANSISTOR RF LOW POWER PNP BF979 TELEFUNKEN AG BF979 28.251
016-3 TRANSISTOR RF BFW92A TFK BFW92A 29.160
017-3 TRANSISTOR J FET N CHANNEL BF245A • MOTOROLA BF245A 29.714
018-3 TRANSISTOR JFET N-CHAN. J309 • SILICONIX J309 29.724
R1-3 RESISTOR MF 20k0 OHM 1% 0.6W 'PHILIPS 2322 156 12003 f· 03.452
R2-3 RESISTOR MF 60k4 OHM 1% 0.6W PHILIPS 2322 156 16043 03.238
R3-3
R4-3
R5·3
RESISTOR MF
RESISTOR MF
RESISTOR MF
33k2 OHM 1% 0.6W
100k OHM 1% 0.6W
221k OHM 1% 0.6W
• PHILIPS
• PHILIPS
'PHILIPS
2322 156 13323
2322 156 11004
232215612214
03.232
03.477
03.483
r"
R6-3 RESISTOR MF 47k OHM 5% 0.4W PHILIPS 2322181 53473 01.241
R7-3
R8·3
RESISTOR MF
RESISTOR MF
6k8 OHM 5% 0.4W
no OHM 5% 0.4W
PHILIPS
PHILIPS
2322 181 53682
2322 181 53221
01.220
01.183
Jr'·
R9·3 RESISTOR MF 33 OHM 5% 0.4W PHILIPS 2322 181 53339 01.162
R10-3
R11·3
R12-3
R13-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
82 OHM 5% 0.4W
12k OHM 5% 0.4W
18k OHM 5% 0.4W
51 OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
PHILIPS
2322 181 53829
2322 181 53123
2322 181 53183
2322 181 53519
01.172
01.227
01.231
01.167
r
R14·3
R15-3
R16-3
R17·3
R18-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
12k OHM 5% 0.4W
3k3 OHM 5% 0.4W
2k0 OHM 5% 0.4W
1k5 OHM 5% 0.4W
18k OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
PHILIPS
PHILIPS
2322 181 53123
2322 181 53332
2322 181 53202
2322 181 53152
2322 181 53183
01.227
01.212
01.207
01.204
01.231
r '

R19·3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R20-3 RESISTOR MF 5k6 OHM 5% 0.4W PHILIPS 2322 181 53562 01.218
R21-3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R22·3 RESISTOR MF 1k5 OHM 5% 0.4W PHILIPS 2322 181 53152 01.204
R23·3 RESISTOR MF 1k3 OHM 1% 0.6W PHILIPS 2322 156 11302 03.402
R24-3 RESISTOR MF 1k3 OHM 1% 0.6W PHILIPS 232215611302 03.402
R25-3 RESISTOR MF 220 OHM 5% 0.4W PHILIPS 2322 181 53221 01.183
A26-3 RESISTOR MF 120 OHM 5% 0.4W PHILIPS 2322 181 53121 01.177
R27-3 RESISTOR MF 60k4 OHM 1% 0.6W PHILIPS 2322 156 16043 03.238

~~
~1:

~
PAGE 7-iO 9724

r
;J 7 PARTS LIST RT2048

J
,~'" ''<.

'· .. /
POSITION

R28-3
DESCRIPTION

RESISTOR MF 60k4 OHM 1% 0.6W

MANUFACTOR

PHILIPS
TYPE

2322 156 16043

PART NO.

03.238
R29-3 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.2'50

I ~

')
R30·3
R31-3
R33-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
30k OHM 5% 0.4W
56 OHM 5% 0.4W
30k OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
2322 181 53303
2322 181 53569
2322 181 53303
01.236
01.168
01.236
{
R34-3 RESISTOR MF 1MO OHM 5% 0.4W PHILIPS 2322 181 53105 01.275

,J R35·3
R36·3
R37-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
330 OHM 5% 0.4W
1k0 OHM 5% 0.4W
110k OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
2322 181 53331
2322 181 53102
2322 181 53114
01.187
01.200
01.251
R38-3 RESISTOR MF 33 OHM 5% 0.4W PHILIPS 2322 181 53339 01.162
R39-3 RESISTOR MF 270k OHM 5% 0.4W PHILIPS 2322 181 53274 01.260
R40·3 RESISTOR MF 820 OHM 5% 0.4W PHILIPS 2322 181 53821 01.197
R41-3 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R42-3 RESISTOR MF 270k OHM 5% 0.4W PHILIPS 2322 181 53274 01.260
R43-3 RESISTOR MF 430 OHM 5% 0.4W 'PHILIPS 2322 181 53431 01.190

(''~"\
I
~!£'}~.
R44-3
R45·3
R46-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
8k2 OHM 5% 0.4W
4k7 OHM 5% 0.4W
1k2 OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
2322 181 53822
2322 181 53472
2322 181 53122
01.222
01.216
01.202

J
R47-3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R48-3 RESISTOR MF 82 OHM 5% 0.4W PHILIPS 2322 181 53829 01.172
~ R49-3 RESISTOR MF 2k43 OHM 1% 0.6W 'PHILIPS 2322 156 12432 03.396
R50-3 RESISTOR MF 56k OHM 5% 0.4W PHILIPS 2322 181 53563 01.243
R51-3 RESISTOR MF 1kO OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R52-3 RESISTOR MF 221 OHM 1% 0.6W 'PHILIPS 2322 15612211 03.384
R53-3 RESISTOR MF 5k11 OHM 1% 0.6W PHILIPS 2322 156 15112 03.414
R54·3 RESISTOR MF 39k2 OHM 1% 0.6W PHILIPS 2322 156 13923 03.439

;
~.X~~
~

'
R55-3
R56·3
R57-3
R58·3
RESISTOR MF
RESISTOR MF
RESISTOR MF
RESISTOR MF
39k2 OHM 1% 0.6W
6k19 OHM 1% 0.6W
10k0 OHM 1% 0.6W
360k OHM 5% 0.4W
PHILIPS
'PHILIPS
PHILIPS
PHILIPS
2322 156 13923
232215616192
2322 156 11003
2322 161 53364
03.439
03.399
03.427
01.263
R59-3 RESISTOR MF 8k2 OHM 5% 0.4W PHILIPS 2322 181 53622 01.222
R60·3 RESISTOR MF 8k2 OHM 5% 0.4W PHILIPS 2322 181 53822 01.222
R61-3 RESISTOR 4.75 KOHM 1% 0.4W 'PHILIPS 2322 156 14752 03.468
R62-3 RESISTOR MF 270k OHM 1% 0.6W PHILIPS 2322 156 12704 03.465
R63-3 RESISTOR MF 750 OHM 5% 0.4W PHILIPS 2322 181 53751 01.196

I '
'~'
R65-3
R66-3
R67-3
RESISTOR MF
RESISTOR MF
RESISTOR MF
150 OHM 5% 0.4W
47 OHM 5% 0.4W
330 OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
PHILIPS
2322 181 53151
2322 181 53479
2322 181 53331
2322 181 53561
01.179
01.166
01.187
01.193
R68·3 RESISTOR MF 560 OHM 5% 0.4W
R69-3 RESISTOR MF 120 OHM 5% 0.4W PHILIPS 2322 181 53121 01.177
R?0-3 RESISTOR MF 15 OHM 5% 0.4W PHILIPS 2322 161 53159 01:154
R71·3 RESISTOR MF 3R9 OHM 5% 0.4W PHILIPS 2322 181 53398 01.139
R72·3 RESISTOR MF 2k2 OHM 5% 0.4W PHILIPS 23221181 53222 01.208
R73-3 RESISTOR MF 100 OHM 5% 0.4W PHILIPS 2322 181 53101 01.175
R74-3 RESISTOR MF 270 OHM 5% 0.4W PHILIPS 2322 181 53271 01.185
R75·3 RESISTOR MF 12 OHM 5% 0.4W PHILIPS 2322 181 53129 01.152
R76·3 RESISTOR MF 27 OHM 5% 0.4W PHILIPS 2322 181 53279 01.160
R77-3 RESISTOR MF 2k7 OHM 5% 0.4W PHILIPS 2322 181 53272 01.210
R78·3 RESISTOR MF 91 OHM 5% 0.4W PHILIPS 2322 181 53919 01.174
R79·3 RESISTOR MF 47 OHM 5% 0.4W PHILIPS 2322 181 53479 01.166
R80-3 RESISTOR MF 1k6 OHM 5% 0.4W PHILIPS 2322 181 53162 01.205
R81-3 RESISTOR MF 4.3k OHM 5% 0.4W 'PHILIPS 2322 181 53432 01.215
R82-3 · RESISTOR MF 3k3 OHM 5% 0.4W PHILIPS 2322 181 53332 01.212
R83-3 RESISTOR MF 560 OHM 5% 0.4W PHILIPS 2322 181 53561 01.193
R84-3 RESISTOR MF 300 OHM 5% 0.4W PHILIPS 2322 181 53301 01.186
R85·3 RESISTOR MF 100 OHM 5% 0.4W PHILIPS 2322 181 53101 01.175
R86·3 RESISTOR MF 300 OHM 5% 0.4W PHILIPS 2322 181 53301 01.186
R87-3 RESISTOR MF 18 OHM 5% 0.4W PHILIPS 2322 181 53189 01.156
R88·3 RESISTOR MF 56 OHM 5% 0.4W PHILIPS 2322 181 53569 01.168
R89·3 RESISTOR MF 5k1 OHM 5% 0.4W PHILIPS 2322 181 53512 01.217
R90·3 RESISTOR MF 75 OHM 5% 0.4W PHILIPS 2322 181 53759 01.171
R91·3 RESISTOR MF 1k8 OHM 5% 0.4W PHILIPS 2322 181 53182 01.206
R92·3 RESISTOR MF 68 OHM 5% 0.4W PHILIPS 2322 181 53689 01.170
R93-3 RESISTOR MF 8R2 OHM 5% 0.4W PHILIPS 2322 181 53828 01.147
R94-3 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R95-3 PRESET CERMET 250k OHM 10% 0.5W 'BOURNS 3386P·1·254 07.895
R96·3 PRESET CERMET 2k0 OHM 5% 0.5W BOURNS 3386P-1·202·11 07.887
R97·3 PRESET CERMET 250k OHM 10% 0.5W 'BOURNS 3386P-1-254 07.895
R98-3 PRESET CERMET 1k0 OHM 10% 0.5W BOURNS 3386P-1-102 07.886
U1·3 QUAD OP.AMP. 324 NAT/SGS LM324N 31.065
U2-3 DUAL O-FF POS TRIG. 74HC74 TEXAS SN74HC74N 34.501
U3·3 SERIAL INPUT PLL SYNTHES. MC145158P2 MOTOROLA MC145158P2 33.492

I ~
~
U4·3
X1-3
9724
INTEGRATED CIRCUIT
CRYSTAL C1075
MC12015P
14.850MHz 5ppm
MOTOROLA'
FAIT
MC12015P
SP.SPEC: C1075
32.850
39.841
PAGE 7-11

II
 I
~
7 PARTS LIST RT2048

~
RXffX MODULE RT2048 ECI AJS 5·0·25448M /4-0-25448K 625448

POSITION DESCRIPTION MANUFACTOR TYPE PART NO. L

VARIOUS SHUNT CONNECTOR FEMALE 2 POLES AMP 142270·1 78.325
VARIOUS
C1·4
C2-4
FUSECLIP
CAPACITOR CERAMIC
CAPACITOR ELECTROLYTIC
FOR 20x5mm FUSELINK
2p7F t/·0.25pF NPO 100VDC
1OOOuF 20% 35VDC
KEYSTONE
PHILIPS
SAMHWA ELEC.
CAT.N0.3521
2222 689 09278
SV-1 OOOuF·35WV
78.396
15.320
14.655
L
C3·4 CAPACITOR MKT 0.1uf 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136

L~
C4·4 CAPACITOR ELECTROLYTIC 4.7uF 20% 50VDC ELNA RJ2-50·V ·4R7·M·T58 14.510
C5·4 CAPACITOR ELECTROLYTIC 22uF 20% 25VDC ELNA RJ2-25-V ·220-M· T58 14.514
C6·4 CAPACITOR ELECTROLYTIC 22uF 20% 25VDC ELNA RJ2·25·V·220·M·T58 14.514 l*l

C7-4 CAPACITOR ELECTROLYTIC 33uf 20% 16VDC ELNA RJ2-16·V·330·M·T58 14.518

C8·4 CAPACITOR ELECTROLYTIC 33uf 20% 16VDC ELNA RJ2·16·V·330·M·T58 14.518
C9·4
C10-4
CAPACITOR ELECTROLYTIC
CAPACITOR ELECTROLYTIC
33uF 20% 16VDC
33uF 20% 16VDC
ELNA
ELNA
RJ2-16·V-330-M·T58
RJ2-16-V-330·M·T58
14.518
14.518
L. .-·
C11·4
R12·4
C13-4
CAPACITOR MKT
CAPACITOR MKT
CAPACITOR CERAMIC
0.1 uF 10% 63VDC
0.1uF 10% 63VDC
10pF 5% NPO 500VDC
PHILIPS
PHILIPS
KCK
2222 370 75104 (78104)
2222 370 75104 (78104)
RT-HM60 SK CH 100 J
11.136
11.136
15.565
L. (

C14·4 CAPACITOR CERAMIC 10pF 5% NPO 500VDC KCK RT-HM60 SK CH 100 J 15.565
C15·4 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT·HM60 SK CH 180 J 15.060

~L
C16·4 CAPACITOR CERAMIC 18pF 5% NPO 500VDC KCK RT -HM60 SK CH 180 J 15.060
C17-4 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35-V -1 OO·M·T58 14.512
C18-4 CAPACITOR ELECTROLYTIC 1OuF 20% 35VDC ELNA RJ2·35·V·100-M-T58 14.512
C19·4 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
C20-4 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
C21-4
C22-4
CAPACITOR MKT
CAPACITOR MKT
0.1uF 10% 63VDC
0.1uF 10% 63VDC
PHILIPS
PHILIPS
2222 370 75104 (78104)
2222 370 75104 (78104)
11.136
11.136
L_
C23-4 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
C24·4 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
C25-4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT-HE60·SK CH 510 J 15.110
C26·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C27·4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT-HE60-SK CH 510 J 15.110
C28·4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT-HE60·SK CH 510 J 15.110 ~--

C29·4
C30·1
C31-4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
22pF 5% NPO 500VDC
22pF 5% NPO 500VDC
22pF 5% NPO 500VDC
KCK
KCK
KCK
RT·HM60 SK CH 220 J
RT·HM60 SK CH 220 J
RT-HM60 SK CH 220 J
15.080
15.080
15.080
l
C32-4 CAPACITOR CERAMIC 15pF 5% NPO 500VDC KCK RT-HM60 SK CH 150 J 15.590
C33-4 CAPACITOR POLYSTYRENE 221 pF 1% 63VDC PHILIPS 2222 443 42211 10.727
C34·4 CAPACITOR MKT 0.1uf 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
CAPACITOR CERAMIC 1OnF -20/t80% CL2 50VDC
r,
C35·4 KCK RT·HE70 SK YF 103 Z . 15.170
f-
C36-4 CAPACITOR CERAMIC 1OnF -20/t80% CL2 50VDC KCK RT-HE70 SK YF 103 Z 15.170
C37-4 CAPACITOR CERAMIC 1OnF ·20/t80% CL2 50VDC KCK RT-HE70 SK YF 103 Z 15.170
C3B·4 CAPACITOR CERAMIC 1OnF -20/+80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170 i
C39·4 CAPACITOR CERAMIC 1Onf ·20/t80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C40·4 CAPACITOR CERAMIC 1OnF ·20/t80% CL2 50VDC KCK RT·HE70 SK YF 103 Z 15.170
C41-4
C42·4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
10nF ·20/+80% CL2 50VDC
22pF 5% N150 500VDC
KCK
KCK
RT·HE70 SK YF 103 Z
RT·HM SK PH 220 J
15.170
15.062
)r
C43·4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT-HE60-SK CH 510 J 15.110
C44·4
C45·4
C46·4
C47·4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
6p8F t·0.5pf N150 50VDC
3p9F t/·0.25pF N150 50VDC
9p1F t/-0.5pF N150 50VDC
9p1F t/-0.5pF N150 50VDC
KCK
KCK
KCK
KCK
RT·HE40 SK PH 6RB D
RT·HE40 SK PJ 3R9 C
RT·HE40 SK PH 9R1 D
RT·HE40 SK PH 9R1 D
15.020
15.003
15.033
15.033
r
r
C48-4 CAPACITOR CERAMIC 9p1F t/·0.5pF N150 50VDC KCK RT·HE40 SK PH 9R1 D 15.033
C49·4 CAPACITOR CERAMIC 9p1F +/·0.5pF N150 50VDC KCK RT·HE40 SK PH 9R1 D 15.033
C50·4 CAPACITOR CERAMIC 3p3F t/·0.25pF N150 500V KCK RT·HM60 SK PJ 3R3 C 16.103
C51·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C52·4 CAPACITOR CERAMIC 470pf 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C53·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C54-4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C55·4 CAPACITOR CERAMIC 470pf 10% 500VDC KCK RT·HM60 SK VB 471 K 16.095
C56·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C57·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C58-4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C59·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C60-4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C61·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C62·4
C63·4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
470pF 10% 500VDC
470pF 10% 500VDC
KCK
KCK
RT·HM60 SK VB 471 K
RT·HM60 SK YB 471 K
16.095
16.095 r*
fl
C64-4 CAPACITOR CERAMIC 470pf 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C65-4
C66·4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
470pF 10% 500VDC
470pF 10% 500VDC
KCK
KCK
RT-HM60 SK YB 471 K
RT·HM60 SK YB 471 K
16.095
16.095
9724
r1
lit
'
PAGE 7-12

r
 7 PARTS LIST RT2048

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

C67·4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT·HM60 SK YB 471 K 16.095
C68·4 CAPACITOR MKT 10nF 20% 100VDC PHILIPS 2222 370 38103 11.168

J C69·4
C70·4
C71·4
CAPACITOR CERAMIC
CAPACITOR CERAMIC
CAPACITOR CERAMIC
470pF 10% 500VDC
470pF 10% 500VDC
470pF 10% 500VDC
KCK
KCK
KCK
RT·HM60 SK YB 471 K
RT·HM60 SK YB 471 K
RT·HM60 SK YB 471 K
16.095
16.095
16.095
C72·4 CAPACITOR CERAMIC 470pF 10% 500VOC KCK RT·HM60 SK YB 471 K 16.095
C73·4 CAPACITOR CERAMIC 1nOF 10% CL2 500VDC KOK RT-HM60 SK YB 102 K 15.160
C74·4 CAPACITOR CERAMIC 180pF 5% N150 50VDC KCK RT·HE95·SK PH 181 J 15.149
C75·4 CAPACITOR CERAMIC 33pF 5% N750 500VDC KCK RT ·HM60 SK UJ 330 J 16.064
C76·4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT·HE60·SK CH 510 J 15.110
C77·4 CAPACITOR CERAMIC 12pF 5% N150 500VDC KCK RT·HM60 SK PH 120 J 16.114
C78·4 CAPACITOR CERAMIC 12pF 5% N150 500VDC KCK RT·HM60 SK PH 120 J 16.114
C79·4 CAPACITOR CERAMIC 18pF 5% N150 50VDC KCK RT·HE40·SK PH 180 J 15.061
C80·4 CAPACITOR MKT 1uF 10% 63VDC PHILIPS 2222 370 78105 11.137
C81·4 CAPACITOR CERAMIC 470pF 10% 500VOC I<CK RT·HM60 SK YB 471 K 16.095
C82·4 CAPACITOR CERAMIC 51 pF 5% NPO 50VDC KCK RT-HE60-SK CH 510 J 15.110
C83·4 CAPACITOR MKT 0.1uF 10% 63VDC PHILIPS 2222 370 75104 (78104) 11.136
C84·4 CAPACITOR CERAMIC 51 pF 5% NPO 50VDC KCK RT-HE60-SK CH 510 J 15.110
C85·4 CAPACITOR CERAMIC 51 pF 5% NPO 50VDC KCK RT·HE60·SK CH 510 J 15.110
C86-4 CAPACITOR CERAMIC 470pF 10% 500VDC KCK RT-HM60 SK YB 471 K 16.095
C87·4 CAPACITOR CERAMIC 10pF 5% NPO 500VDC KCK RT-HM60 SK CH 100 J 15.565
C88·4 CAPACITOR CERAMIC 1nF 10% 50VDC CL2 KCK RT·SK-HE50 SJYB 102 K 16.160
C89·4 CAPACITOR CERAMIC 51pF 5% NPO 50VDC KCK RT·HE60-SI( CH 510 J 15.110
01·4 TRANSIENT SUPPRESSOR 18V 1N6277A, PFZ18A, KE1.5KE1 MOTOROLA 1N6277ARL4 26.765
02·4 DIODE 1N4148 HIGH SPEED PHILIPS 1N4148-143 25.131
03·4 DIODE CAPASITANCE 13pF/9VDC TOSHIBA 1SV1 01 In matched group 26.135
04-4 DIODE CAPASITANCE 13pF/9VDC TOSHIBA 1SV101 In matched group 26.135
05·4 DIODE CAPASITANCE 13pF/9VDC TOSHIBA 1SV1 01 in matched group 26.135
06·4 DIODE CAPASITANCE 13pF/9VDC TOSHIBA 1SV101 in matched group 26.135
07·4 DIODE SWITCH BA282 TFK BA 282 TAPED 25.390
F1·4 FUSE 6.3AF 250V 5x20mm LITIELFUSE 21706.3 45.571
FL1·4 CERAMIC FILTER Fc=450kHz BW=20kHz MURATA SFP 450DR 41.512
FL2·4 CRYSTAL FILTER Fc=15.3MHz 'NDK SP.SPEC: C1076 (15N15B) 40.029
J1·4 SOCKET 1/10' SIL 12 POLES PRECI·DIP 310·91-112 78.805
J2·4 SOCKET COAX 90 DEG. PCB VERSION TAIKO TMP·J01X.V6 78.518
J3-4 SOCKET COAX 90 DEG. PCB VERSION TAIKO TMP-J01X·V6 78.518
J4·4 ANTENNA JACK (FEMALE) 80239 KAJ V HANSEN S0239 78.504
J5·4 SOCKET COAX 90 DEG. PCB VERSION TAIKO TMP-J01 X·V6 78.518
L1·4 CHOKE TL487 ECI NS 6-0-254578 400487
L2·4 CHOKE TL487 ECINS 6·0·25457B 400487
L3·4 CHOKE TL486 ECINS 6·0·25456C 400486
L4·4 CHOKE 5u6H 10% 'FASTRON SMCC·5R6K·02 20.139
L5·4 CHOKE TL488 70nH ECINS 6·0-26458 400488
L6·4 COIL RF 568nH ADJUSTABLE SUMIDA ELEC.CO. P·75B /2175·2239·1025 38.432
L7-4 COIL TL067 ECI NS 6·0-20854A 400067
400067=20.053
L8·4 COIL TL067 ECI NS 6·0·20854A 400067
400067=20.053
L9·4 COIL RF 11 OnH ADJUSTABLE TOKO E526HN· 100117 38.409
L10-4 COIL RF 110nH ADJUSTABLE TOKO E526HN· 100117 38.409
L11·4 COIL RF 110nH ADJUSTABLE TOKO E526HN· 100117 38.409
L12·4 COIL RF 110nH ADJUSTABLE TOKO E526HN· 100117 38.409
L13·4 COIL TL067 ECI NS 6·0·20854A 400067
400067=20.053
LC1·4 EMI SUPPRESSION FILTER Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
LC2·4 EMI SUPPRESSION FILTER Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
LC3·4 EMI SUPPRESSION FILTER Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
LC4·4 EMI SUPPRESSION FILTEA Fo=70MHz MURATA DST310-92(91)Y5S 222M 100 18.550
LC5·4 EMI SUPPRESSION FILTEA Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
LC6·4 EMI SUPPRESSION FILTEA Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
LC7-4 EMI SUPPRESSION FILTEA Fo=70MHz MURATA DST310·92(91)Y5S 222M 100 18.550
P1-4 PLUG 6 POLES HIRSCHMANN 973 887·100 78.315
P2·4 PLUG 2x5 POLES 3M 3654-6002/7610·6002 JL 78.251
P3·4 PLUG 2x10 POLES 3M 3592·6002 I 7620·6002 JL 78.250
P4·4 SOCKET SUB D 9 POLES PCB VERSION 2x 4-40 NUT EDA INC. 8T0-009SS-244T(144T,344T) 78.164
P5·4 PLUG 1/10' OIL SO.PINS 6 POLES AMP 826656-3 78.340
01·4 TRANSISTOR AF MED.POWER BD234·BD236·BD238 MOTOROLA BD238 (80234,80236) 29.070
02-4 TRANSISTOR BF199 PHILIPS 8F199·126 28.179
03·4 TRANSISTOR BF199 PHILIPS BF199·126 28.179
04·4 TRANSISTOR BF199 PHILIPS BF199·126 28.179
05-4 TRANSISTOR BC557C 'PHILIPS BC557C·126 28.092
06·4 TRANSISTOR BC557C 'PHILIPS BC557C-126 28.092
07·4 TRANSISTOR BC557C 'PHILIPS BC557C·126 28.092

9724 PAGE7-i3

I
!
 I
~-
7 PARTS LIST RT2048

POSITION

08-4
DESCRIPTION

TRANSISTOR N-CHAN. JFET TIS88A1

MANUFACTOR

MOTOROLA
TYPE

TM 00 044 ·1
PART NO.

29.735
~
I
\
09-4 TRANSISTOR N-CHAN. JFET TIS88A1 MOTOROLA TM 00 044-1 29.735
010-4 TRANSISTOR MOSFET DUAL GATE N·CHAN.BF964SA TFK BF964SA 28.240
011-4 TRANSISTOR MOSFET DUAL GATE N-CHAN.BF964SA TFK BF964SA 28.240 lm-
012-4
013-4
TRANSISTOR AF
TRANSISTOR AF
NPN BC547C T0-92
NPN BC547C T0-92
PHILIPS
PHILIPS
BC547C-126
BC547C-126
28.068
28.068
,.
014-4
R1-4
R2·4
R3-4
TRANSISTOR DARLINGTON
RESISTOR MF
RESISTOR MF
RESISTOR MF
NPN BC618
475 OHM 1% 0.6W
1k3 OHM 1% 0.6W
221 OHM 1% 0.6W
MOTOROLA
'PHILIPS
PHILIPS
'PHILIPS
BC618 RL1
2322 156 14751
2322 156 11302
232215612211
28.107
03.393
03.402
03.384
k
L~
R4-4 PRESET CERMET 50 OHM 10% 0.5W BOURNS 3386P· Y91·500 07.882
R5-4 RESISTOR MF 2R7 OHM 5% 0.4W PHILIPS 2322 181 53278 01.135
R6·4 RESISTOR MF 3k92 OHM 1% 0.6W PHILIPS 2322 156 13922 03.409
R7-4 RESISTOR MF 3k92 OHM 1% 0.6W PHILIPS 2322 156 13922 03.409
R8-4
R9·4
R10-4
RESISTOR MF
RESISTOR MF
RESISTOR MF
97k6 OHM 1% 0.6W
97k6 OHM 1% 0.6W
18k OHM 5% 0.33W
PHILIPS
PHILIPS
PHILIPS
2322 156 19763
2322 156 19763
2322 187 73183
03.471
03.471
02.502
L·
R11-4 RESISTOR MF 43k OHM 5% 0.4W PHILIPS 2322 181 53433 01.240 ~:
R12-4 RESISTOR MF 22k OHM 5% 0.4W PHILIPS 2322 181 53223 01.233
R13·4
R14-4
RESISTOR MF
RESISTOR MF
2k0 OHM 5% 0.4W
1k5 OHM 5% 0.4W
PHILIPS
PHILIPS
2322 181 53202
2322 181 53152
01.207
01.204 L~
R15-4 RESISTOR PMF 2200HM 5%2W PHILIPS 2322 194 13221 04.183 ..
,
R16·4 RESISTOR MF 5k6 OHM 5% 0.4W PHILIPS 2322 181 53562 01.218
R17-4
R18·4
R19-4
RESISTOR MF
RESISTOR MF
PRESET CERMET
3k3 OHM 5% 0.4W
8k2 OHM 5% 0.4W
500 OHM 10% 0.5W
PHILIPS
PHILIPS
BOURNS
2322 181 53332
2322 181 53822
3386P-Y91·501
01.212
01.222
07.885
\L
R20·4 PRESET CERMET 50k 10% 0.5W BOURNS 3386P· Y91-503 07.892
R21-4
R22-4
R23-4
PRESET CERMET
RESISTOR MF
RESISTOR MF
2k0 OHM 5% 0.5W
2k2 OHM 5% 0.4W
2k2 OHM 5% 0.4W
BOURNS
PHILIPS
PHILIPS
3386P-Y91·202
2322 181 53222
2322 181 53222
07.887
01.208
01.208
I
R24-4
A25·4
R26·4
RESISTOR MF
RESISTOR MF
RESISTOR MF
2k7 OHM 5% 0.4W
2k2 OHM 5% 0.4W
470 OHM 5% 0.4W
PHILIPS
PHILIPS
PHILIPS
2322 181 53272
2322 181 53222
2322 181 53471
01.210
01.208
01.191
r
~
R27-4 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R28-4 RESISTOR MF 1k8 OHM 5% 0.4W PHILIPS 2322 181 53182 01.206
R29·4 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R30-4 RESISTOR MF 47k OHM 5% 0.4W PHILIPS 2322 181 53473 01.241
R31-4 RESISTOR MF 12k OHM 5% 0.4W PHILIPS 2322 181 53123 01.227
R32-4 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R33·4 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
R34-4 RESISTOR MF 5k36 OHM 1% O.GW PHILIPS 2322 156 15362 03.418
R35-4 RESISTOR MF 220k OHM 5% 0.4W PHILIPS 2322 181 53224 01.258
R36-4 RESISTOR MF 3k9 OHM 5% 0.33W PHILIPS 2322 187 73392 02.486
R37-4 RESISTOR MF 3k9 OHM 5% 0.4W PHILIPS 2322 181 53392 01.214
R38·4 RESISTOR MF 3k9 OHM 5% 0.4W PHILIPS 2322 181 53392 01.214
R39-4 RESISTOR MF 3k9 OHM 5% 0.33W PHILIPS 2322 187 73392 02.486
R40-4 RESISTOR MF 560 OHM 5% 0.4W PHILIPS 2322 181 53561 01.193
R41·4 RESISTOR MF 180 OHM 5% 0.4W PHILIPS 2322 181 53181 01.181 Jrit~
R42-4 RESISTOR MF 120k OHM 5% 0.4W PHILIPS 2322 181 53124 01.252
~
R43·4 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.250
R44-4 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.250
R45-4 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.250
R46·4 RESISTOR MF 470k OHM 5% 0.4W PHILIPS 2322 181 53474 01.266 r~
R47-4 RESISTOR MF 56k OHM 5% 0.33W PHILIPS 2322 187 73563 02.514 ..
R48·4 RESISTOR MF 100k OHM 5% 0.4W PHILIPS 2322 181 53104 01.250
R49·4 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R50·4 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R51·4 RESISTOR MF 39k OHM 5% 0.4W PHILIPS 2322 181 53393 01.239
R52·4 RESISTOR MF 39k OHM 5% 0.4W PHILIPS 2322 181 53393 01.239
R53·4 RESISTOR MF 39k OHM 5% 0.4W PHILIPS 2322 181 53393 01.239
R54·4 RESISTOR MF 39k OHM 5% 0.4W PHILIPS 2322 181 53393 01.239
R55-4 RESISTOR MF 120k OHM 5% 0.33W PHILIPS 2322 187 73124 02.522
R56·4 RESISTOR MF 15k OHM 5% 0.4W PHILIPS 2322 181 53153 01.229
R57-4 RESISTOR MF 15k OHM 5% 0.33W PHILIPS 2322 187 73153 02.500
R58·4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R59·4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R60-4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R61·4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R62-4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R63·4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235
R64·4 RESISTOR MF 27k OHM 5% 0.4W PHILIPS 2322 181 53273 01.235

9724
PAGE 7-14
\,
J !

7 PARTS LIST RT2048

J POSITION

R65·4
DESCRIPTION

RESISTOR MF 27k OHM 5% 0.4W

MANUFACTOR

PHILIPS
TYPE

2322 181 53273

PART NO.

01.235
R66·4 RESISTOR MF 68k OHM 5% 0.4W PHILIPS 2322 181 53683 01.245

'\,
J R67-4
RE1·4
TR1·4
RESISTOR MF
RELAY
TRAFO RF 2u7H ADJUSTABLE
56k OHM 5% 0.33W
12VDC 2SH 1.25A
PHILIPS
MEISEl
TOKO
2322 187 73563
M1B·12-H
F292MNS·3342BQE
02.514
21.030
38.431
TR2·4 TRAFO 157MHz ADJUSTABLE SUMIDA ELEC.CO. S·7GD I 0237·1756 38.430
U1-4 POS. VOLTAGE REG. ADJUST. lo=1.5A LM317T MOTOROLA LM317T 31.055
I.J U2·4
U3-4
AF POWER AMPLIFIER
NBFM IF SYSTEM
TDA1515A
MC3361
PHILIPS
PHILIPS
TDA1515A
MC 3361 N
31.489
31.325
U4·4 VHF POWER AMP. 25W S·AV6/M5771 ONMC5233 MITSUBISHI M57710·A 32.450

A SELCALL MODULE (OPTIONAL) RT2048 ECI A/S 5·0·254498 I 4·0·254490 625449

I~

/"~)
POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

C1·5 CAPACITOR KP 10nF 2.5% 63VDC EVOX* PFR 103H TA18 13.407

J C2-5
C3·5
C4-5
C5·5
CAPACITOR KP
CAPACITOR KP
CAPACITOR KP
CAPACITOR MKT
10nF 2.5% 63VDC
3.9nF 2.5% 63VDC
3.9nF 2.5% 63VDC
22nF 10% 1OOVDC
EVOX*
EVOX*
EVOX*
PHILIPS
PFR 103H TA18
PFR 392H TA18
PFR 392H TA18
2222 370 88223
13.407
13.402
13.402
11.175
C6·5 CAPACITOR MKT 150nF 5% 50VDC ERO MKT 1826·415/06 4-G 11.181
C7-5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
C8·5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
C9·5 CAPACITOR MKT 47nF 10% 63VDC EVOX' MMK5 473K63 TA18 11.644
C10·5 CAPACITOR MKT 47nF 10% 63VDC EVOX' MMK5 473K63 TA18 11.644
C11·5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
C12·5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
C13-5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
C14·5 CAPACITOR MKT 47nF 10% 63VDC EVOX* MMK5 473K63 TA18 11.644
D1·5 DIODE SCHOTTKY BAT 43 THOMSON-CSF BAT43 27.600
D2·5 DIODE SCHOTTKY BAT 43 THOMSON-CSF BAT43 27.600
J1·5 SOCKET COAX FOR PCB 45 DEG. HORIZONTAL TAIKO TMP-J01X-A2 78.517
J2-5 SOCKET 7 POLES F.RIBBON CABLE MOLEX 52011-0710 78.280
~~
lit
01·5
R1·5
TRANSISTOR RF SWITCH
PRESET CERMET
2N2369A
2k0 OHM 5% 0.5W
MOTOROLA
BOURNS
2N2369A
3386P·1·202·11
28.315
07.887
R2·5 RESISTOR MF 6k49 OHM 1% 0.6W 'PHILIPS 2322 156 16492 03.412
R3·5 RESISTOR MF 243 OHM 1% 0.6W 'PHILIPS 2322156 12431 03.385
R4·5 RESISTOR MF 7k50 OHM 1% 0.6W 'PHILIPS 2322 156 17502 03.448
R5·5 RESISTOR MF 7k50 OHM 1% 0.6W 'PHILIPS 2322 156 17502 03.448
R6·5 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R7·5 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322~181 53103 01.225
R8·5 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R9·5 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R10·5 RESISTOR MF 12k OHM 5% 0.4W PHILIPS 2322 181 53123 01.227
R11·5 RESISTOR MF 330 OHM 5% 0.4W PHILIPS 2322 181 53331 01.187
R12·5 RESISTOR MF 680k OHM 5% 0.4W PHILIPS 2322 181 53684 01.270
R13·5 RESISTOR MF 330k OHM 5% 0.4W PHILIPS 2322 181 53334 01.262
R14-5 RESISTOR MF 453k OHM 1% 0.6W 'PHILIPS 2322 156 14534 03.516
R15·5 RESISTOR MF 7k50 OHM 1% 0.6W 'PHILIPS 2322 156 17502 03.448
R16-5 RESISTOR MF 390k OHM 5% 0.4W PHILIPS 2322 181 53394 01.264
R17-5 RESISTOR MF 390k OHM 5% 0.4W PHILIPS 2322 181 53394 01.264
R18·5 RESISTOR MF 20k0 OHM 1% 0.6W 'PHILIPS 2322 156 12003 03.452
R19·5 RESISTOR MF 61k9 OHM 1% 0.6W *PHILIPS 2322 156 16193 03.239
R20·5 RESISTOR MF 4k7 OHM 5% 0.4W PHILIPS 2322 181 53472 01.216
R21·5 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R22·5 RESISTOR MF 3k0 OHM 5% 0.4W PHILIPS 2322 181 53302 01.211
R23·5 RESISTOR MF 12k OHM 5% 0.4W PHILIPS 2322 181 53123 01.227
R24·5 RESISTOR MF 2k2 OHM 5% 0.4W PHILIPS 2322 181 53222 01.208
R25·5 RESISTOR MF 7k50 OHM 1% 0.6W 'PHILIPS 232215617502 03.448
U1·5 INTEGRATED CIRCUIT LF347N #NATIOPNAL LF347N 31.530
U2·5 QUAD ANALOG SWITCH MC14066B/CD4066B MOTOROLA MC14066BCP 33.232
U3-5 DUAL TYPE 0 FLIP-FLOP MC14013BCP MOTOROLA' MC14013BCP 33.056
U4-5 DUALOP AMP LM358N TEXAS LM358P 31.100
U5-5 POS. VOLTAGE REG. FIXED 5V 5% 0.1 A 78LOSAC MOTOROLA* MC78L05ACP 31.135
U6-5 INTEGRATED CIRCUIT MC14569BCP 'MOTOROLA MC14569BCP 33.449
U7-5 INTEGRATED CIRCUIT MC14094BCP MOTOROLA' MC14094BCP 33.305
U8-5 IC CMOS HEX LEVEL SHIFTER MOTOROLA MC 14504 BCP 33.282

9724
PAGE 7-15

I
I
.
7 PARTS LIST RT2048
~

I
~~ ',

SELCALL ALARM (MODULE 6) SPECIAL OPTION FOR RT2048 ECI AIS 4·0-25660 I 5-0-25473 625660
I
POSITION DESCRIPTION MANU FACTOR TYPE PART NO. ~'li:J
{('

D1 DIODE HIGH SPEED 1N4448 PHILIPS 1N4448 25.147

~-
P1 PLUG 1/1 0" SIL 12 POLES EURODIP SL 12 OZ 78.328
01 TRANSISTOR DARLINGTON NPN BC618 MOTOROLA BC618 28.107
R114 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615
RE1 RELAY 12VDC 1SH. 2A. ORIGINAL ELEC. OUC-SS-112D (-S-/-SH-) 21.300
RE2 RELAY 12VDC 1SH. 2A. ORIGINAL ELEC. OUC-SS-112D (-8-/-SH-) 21.300
L} -~
:,~.:

DISTRESS OUTPUT(MODULE 6) SPECIAL OPTION FOR RT2048 ECI AIS 4·0-25661/5-0-25473 625661
I.
~s;;:~'S

POSITION DESCRIPTION MANUFACTOR TYPE PART NO. (

D3
P1
03
DIODE HIGH SPEED
PLUG
TRANSISTOR
1N4448
1/10" SIL 12 POLES
BC638
PHILIPS
EURODIP
MOTOROLA'
1N4448
SL 12 OZ
BC638 I BC640
25.147
78.328
28.117
L
04 TRANSISTOR DARLINGTON NPN BC618 MOTOROLA BC618 28.107 •''
R1/4
R214
R212
RESISTOR ARRAY
RESISTOR ARRAY
RESISTOR ARRAY
4x10k OHM 5% 1/8W
4x10k OHM 5% 1/8W
4x10k OHM 5% 1/8W
PANASONIC
PANASONIC
PANASONIC
EXBF8V103G (4X10K)
EXBF8V103G (4X10K)
EXBF8V103G (4X10K)
08.615
08.615
08.615
Jr.
R2/3 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615
R3
R4
RESISTOR MF
RESISTOR MF
1k0 OHM 5% 0.4W
1k0 OHM 5% 0.4W
PHILIPS
PHILIPS
2322 181 53102
2322181 53102
01.200
01.200
L
AUX INTERFACE (MODULE 6) SPECIAL OPTION FOR RT2048 ECI AIS 5-0-25473 625473

POSITION DESCRIPTION MANU FACTOR TYPE PART NO.

i
D1 DIODE HIGH SPEED 1N4448 PHILIPS 1N4448 25.147
D2 DIODE HIGH SPEED 1N4448 PHILIPS 1N4448 25.147
D3 DIODE HIGH SPEED 1N4448 PHILIPS 1N4448 25.147
P1 PLUG 1/10' SIL 12 POLES EURODIP SL 12 0 Z 78.328
01 TRANSISTOR DARLINGTON NPN BC618 MOTOROLA BG618 28.107
02 TRANSISTOR DARLINGTON NPN BC618 MOTOROLA BC618 28.107
03 TRANSISTOR BC638 MOTOROLA' BC638/ BC640 28.117
04 TRANSISTOR DARLINGTON NPN BC618 MOTOROLA BC618 ~
28.107
R1/4 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIG EXBF8V103G (4X10K) 08.615 f"'"
R2/4 RESISTOR ARRAY 4x10k OHM 5% 1/8W PANASONIC EXBF8V103G (4X10K) 08.615
R3 RESISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200 I
R4 R!:SISTOR MF 1k0 OHM 5% 0.4W PHILIPS 2322 181 53102 01.200
RE1 RELAY 12VDC 1SH. 2A. ORIGINAL ELEG. OUC-SS-112D (-S-/-SH-) 21.300
RE2 RELAY 12VDC 1SH. 2A. ORIGINAL ELEG. OUC-SS-112D (-S-/-SH-) 21.300
RE3 RELAY 12VDC 1SH. 2A. ORIGINAL ELEC. OUC-SS-112D (-8-/-SH-) 21.300

r·
RE4 RELAY 12VDC 1SH. 2A. ORIGINAL ELEC. OUC-SS-1120 (-S·/·SH-) 21.300
U1 OPTO COUPLER CNY17-3 MOTOROLA GNY17-3 32.533

BUS-INTERRUPT OPTION (6) RM2042 ECI AIS 5·0·269458 /4·0-26945 626945

r~

POSITION DESCRIPTION MANUFACTOR TYPE PART NO.

I
C1·6 CAPACITOR CERAMIC 1nOF 1Oo/o CL2 500VDC KCK RT·HM60 SK VB 102 K 15.160
P1·6 PLUG 1/1 0" SIL 12 POLES EURO DIP SL12 0 Z 78.328
QH TRANSISTOR AF NPN BC547C T0-92 PHILIPS BC547C 28.068
R1-6 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225
R2-6 RESISTOR MF 10k OHM 5% 0.4W PHILIPS 2322 181 53103 01.225

9724
PAGE?-16
 9724 PAGE 7-17

I
'