Medium voltage fuses — 7

Contents
Section
Description page
Introduction 2

A fusible solution for virtually E-Rated current-limiting

2.75 kV 3-4
every medium voltage 5.5 kV 5-7
5.5 kV specialty mount 8-10
application 8.3 kV 11-12
8.3 kV specialty mount 13-14
15.5 kV 15-17
15.5 kV specialty mount 18-19
DIN E-Rated current-limiting — 5.5-38 kV 20-21
R-Rated current-limiting
2.4 kV 22
4.8 kV 23-24
7.2 kV 25
PT E-Rated current-limiting — 2.475-38 kV 26-29
PT fast-acting current-limiting 30
British IEC 31
DIN IEC 32
Expulsion fuse links 33
EEI-NEMA Type K and T – Type H and N 34
PT fuse mountings 35
Recommended fuseclips 36

Bussmann series

Medium voltage
E-Rated, R-Rated and PT

fuses
medium voltage fuses

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-1
7 — Medium voltage fuses
Introduction E- and R-Rated fuses

In North America, current limiting fuses typically fall into the

Worldwide circuit protection solutions category of E-Rated fuses and R-Rated fuses. Eaton also offers a
wide range of Bussmann series current limiting fuses designed to
Eaton is the world-leading supplier of Bussmann series medium BS, DIN and IEC standards.
voltage fuses. Each product is backed by an efficient worldwide
distribution network with unrivaled service and technical support. E-Rated fuses are used to protect feeder circuits, power
Eaton circuit protection solutions comply with major international transformers and potential transformers. E-Rated fuses have defined
standards: ANSI, BS, DIN, IEC and UL. current response times specified by ANSI C37.46. E-Rated fuses
100 amps and below must melt in 300 seconds at an RMS current
Fuse types within the range of 200 to 240 percent of the continuous current
rating. E-Rated fuses above 100 amps must melt in 600 seconds
Medium voltage fuses generally fit into two categories – expulsion at an RMS current within the range of 220 to 264 percent of the
fuses and current limiting. The definitions per ANSI C37.40 are: continuous current rating of the fuse. Eaton offers a wide variety of
full range and general purpose E-Rated fuses from 2.4 to 38 kV.
Expulsion fuse: A vented fuse in which the expulsion effect of the
gases produced by internal arcing, either alone or aided by other R-Rated fuses are back-up fuses that provide short-circuit protection
mechanisms results in current interruption. Expulsion fuses will for motor circuits. They are applied with medium voltage motor
limit the duration of an overcurrent event, but they will not limit the starters which provide the overload protection for the circuit. R-Rated
magnitude of fault current. fuses also have defined current response times specified by ANSI
C37.46. R-Rated fuses will melt in a range of 15 to 35 seconds at a
Current-limiting fuse: A fuse unit that, when in its current- current equal to 100 times the “R” rating. Bussmann series R-Rated
responsive element is melted by a current within the fuse’s fuses for motor circuit protection are available in voltage ratings from
specified current-limiting range, abruptly introduces a high 2.4 to 8.3 kV
resistance to reduce current magnitude and duration, resulting in
subsequent current interruption. A current limiting fuse will reduce
the magnitude a fault current as well as limit the duration of the
overcurrent event when operating in its current limiting range.
Eaton offers a broad range of current limiting fuses for protection of
feeders, transformers and motor circuits designed to ANSI, BS, DIN
and IEC standards.

Medium voltage current-limiting fuses

Current-limiting fuses are classified into three categories:

1. Full range – defined by ANSI C37.40 as “a fuse capable of
interrupting all currents from the maximum rated interrupting
current down to the minimum continuous current that causes the
melting of the fusible element(s), when the fuse is applied at the
maximum ambient temperature specified by the manufacturer.” It
is able to interrupt any current that will melt its element.
2. General purpose – defined by ANSI C37.40 as “a fuse capable
of interrupting all currents from the maximum rated interrupting
current down to the current that causes melting of the fusible
element(s) in one hour.” Not all currents fall within this range. It is
possible for the fuse to be exposed to an overcurrent lower than
the value given by the one hour criteria. In that case, a different
overcurrent protection device would be required to interrupt the
overcurrent.
3. Back-up – defined by ANSI C37.40 as “a fuse capable of
interrupting all currents from the maximum interrupting rating
current down to the minimum interrupting current.” The minimum
interrupting current is the lowest current that the fuse will be
able to clear properly. This creates a need to place a low current
interrupting device, such as motor overloads, in series with the
back-up rated fuse.

7-2 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
2.75 kV E-Rated medium voltage ferrule fuses Dimensions — in (mm)

Catalog symbols C
•• 2CLE-_E
B
•• JCX-_E

Ratings

•• Volts 2.75 kV
•• Amps 10 to 450 A
3.31
•• Interrupting ratings (84.1)
•• 50 kA RMS Sym. (2CLE-_E) B
•• 40 kA RMS Sym. (JCX-_E)
A
Agency information

•• E-Rated fuses meet the performance characteristics of ANSI

C37.46

Recommended CLE fuse holders

Catalog no.
Approx. dimensions — in (mm) Mounting* Live parts End fittings
Fuse mounting BIL Porcelain Glass-polyester (with end (disconnect
Amps type (kV) Diameter A Clip center B Length C insulator insulator fittings) only)
CLE
15E–25E Non-disconnect 2CLE-PNM-C 2CLE-GNM-C CLE-NL-C —
2 (51) 8.1 (206) 9.5 (241)
Single barrel Disconnect† 2CLE-PDM-C 2CLE-GDM-C CLE-DL-C CLE-DF-C
10E–225E Non-disconnect 2CLE-PNM-D 2CLE-GNM-D CLE-NL-D —
Single barrel Disconnect† 60 2CLE-PDM-D 2CLE-GDM-D CLE-DL-D CLE-DF-D
250E–300E Non-disconnect 3 (76) 7 (178) 10.9 (277) 2CLE-PNM-E 2CLE-GNM-E CLE-NL-E —
350X-450X
Double barrel Disconnect †
2CLE-PDM-E 2CLE-GDM-E CLE-DL-E CLE-DF-E
* Includes live parts and end fittings, end fittings supplied only when required.
† Disconnect mountings provide a means for fuse extraction only. Do not use a
disconnect mounting for load switching or fuse removal while energized.

Recommended fuseclips
Description Fuse dia. — in (mm) Catalog no.
2 (51) A3354710*
Enclosed fuseclip
A3354730*
Open fuseclip 3 (76) 1A0065

Medium voltage
Spring loaded open fuseclip 9078A67G04

fuses
* For single barrel applications only. Not sold in pairs.

Data sheet no. 10350

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-3
7 — Medium voltage fuses
CLE and JCX
Dimensions — in (mm)
Amps Length A Diameter B Clip centers C IR RMS Sym. (kA) No. of barrels Installation location Catalog no.
1 JCX-1E
2 JCX-2E
3 JCX-3E
9.2 (234) 2 (51) 40 Indoor/outdoor
5 7 (178) JCX-5E
7 JCX-7E
10 JCX-10E
10 10.9 (277) 3 (76) 2CLE-10E
15 2CLE-15E
20 9.5 (241) 2 (51) 8.1 (206) 2CLE-20E
25 2CLE-25E
1
30 2CLE-30E
40 2CLE-40E
50 2CLE-50E
65 2CLE-65E
80 2CLE-80E
100 50 Indoor 2CLE-100E
125 2CLE-125E
150 10.9 (277) 3 (76) 7 (178) 2CLE-150E
200 2CLE-200E
225 2CLE-225E
250* 2CLE-250E
300* 2CLE-300E
350** 2 2CLE-350X
400** 2CLE-400X
450** 2CLE-450X
* 250 and 300 amp ratings may also be applied at 280 and 325 amps respectively, but fuses will no longer be complaint with ANSI E rating criteria.
** Does not comply with ANSI C37.46 for “E” rating.

Data sheet no. 10350

7-4 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
5.5 kV E-Rated medium voltage ferrule fuses Dimensions — in (mm)

Catalog symbols C

•• General purpose B
•• 5CLE-_E-D (10-25 A)
•• 5CLE-_E (10-1350 A)
•• 5HLE-_E (10-450 A)
•• JCY-_E (1-25 A)
•• Full range (per ANSI C37.40) 3.31
(84.1)
•• MV055F_ (10-450 A)
B
Ratings*
A
•• Volts 5.5 kV
•• Amps 1 to 1350 A
•• Interrupting ratings 40 to 63 kA RMS Sym.
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.

Agency information

•• E-Rated fuses meet the performance characteristics of ANSI

C37.46
•• UL Listed, Guide JEEG, File E240398. See catalog numbers.

Recommended fuseclips
Description Fuse dia. — in (mm) Catalog no.
2 (51) A3354710*
Enclosed fuseclip
A3354730*
Open fuseclip 3 (76) 1A0065
Spring loaded open fuseclip 9078A67G04

* For single barrel applications only. Not sold in pairs.

Recommended CLE and HLE holders

Catalog no.
Approx. Dimensions — in (mm) Mounting* Live parts End fittings
Fuse mounting BIL Diameter Clip center Porcelain Glass-polyester (with end (disconnect
Amps type (kV) A B Length C insulator insulator fittings) only)
CLE

Medium voltage
10E-D–25E-D Non-disconnect 5CLE-PNM-D 5CLE-GNM-D CLE-NL-D —

fuses
30E–250E 3.0 (76.2) 14.0 (355.6) 17.9 (454.7)
Single barrel Disconnect †
5CLE-PDM-D 5CLE-GDM-D CLE-DL-D CLE-DF-D
15E–25E Non-disconnect 5CLE-PNM-C 5CLE-GNM-C CLE-NL-C —
2.0 (50.8) 11.5 (292.1) 12.9 (327.7)
Single barrel Disconnect† 60 5CLE-PDM-C 5CLE-GDM-C CLE-DL-C CLE-DF-C
300E–450E Non-disconnect 5CLE-PNM-E 5CLE-GNM-E CLE-NL-E —
3.0 (76.2) 14.0 (355.6) 17.9 (454.7)
Double barrel Disconnect† 5CLE-PDM-E 5CLE-GDM-E CLE-DL-E CLE-DF-E
600E and 750E Consult factory
Double barrel
1100E and 4.0 (101.6) N/A N/A — — — —
1350E Consult factory —
Four barrel
HLE
10E-D–250E Non-disconnect 5HLE-PNM-D 5HLE-GNM-D CLE-NL-D —
Single barrel Disconnect 5HLE-PDM-D 5HLE-GDM-D CLE-DL-D CLE-DF-D
60 3.0 (76.2) 12.0 (304.8) 15.9 (403.9)
300E–450E Non-disconnect 5HLE-PNM-E 5HLE-GNM-E CLE-NL-E —
Double barrel Disconnect 5HLE-PDM-E 5HLE-GDM-E CLE-DL-E CLE-DF-E
* Including live parts and end fittings, end fittings supplied only when required.
† Disconnect mountings provide a means for fuse extraction only. Do not use a
disconnect mounting for load switching or fuse removal while energized.

Data sheet no. 10351

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-5
7 — Medium voltage fuses
CLE, HLE and JCY general purpose
Dimensions — in (mm) IR RMS Sym. Installation
Amps Length A Diameter B Clip centers C (kA) No. of barrels location Catalog no.
1 JCY-1E
2 JCY-2E
3 JCY-3E
11.2 (284) 2 (51) 9 (229) 40
5 JCY-5E
7 Indoor/outdoor JCY-7E
10 JCY-10E
10 17.9 (455) 14 (356) 5CLE-10E-D
3 (76) 63
10 15.9 (404) 12 (305) 5HLE-10E
15 11.2 (284) 9 (229) 40 JCY-15E
2 (51)
15 12.9 (328) 11.5 (292) 50 Indoor 5CLE-15E*
15 17.9 (455) 14 (356) 5CLE-15E-D
3 (76) 63
15 15.9 (404) 12 (305) Indoor/outdoor 5HLE-15E
20 11.2 (284) 9 (229) 40 JCY-20E
2 (51)
20 12.9 (328) 11.5 (292) 50 Indoor 5CLE-20E*
20 17.9 (455) 14 (356) 5CLE-20E-D
3 (76) 63
20 15.9 (404) 12 (305) Indoor/outdoor 5HLE-20E
25 11.2 (284) 2 (51) 9 (229) 40 JCY-25E
25 12.9 (328) 2 (51) 11.5 (292) 50 Indoor 5CLE-25E*
25 17.9 (455) 14 (356) 5CLE-25E-D
25 15.9 (404) 12 (305) 5HLE-25E
63
30 17.9 (455) 14 (356) 5CLE-30E
1
30 15.9 (404) 12 (305) 5HLE-30E
40 17.9 (455) 14 (356) 5CLE-40E†
40 15.9 (404) 12 (305) 5HLE-40E†
50 17.9 (455) 14 (356) 5CLE-50E†
50 15.9 (404) 12 (305) 5HLE-50E†
65 17.9 (455) 14 (356) 5CLE-65E†
65 15.9 (404) 12 (305) 5HLE-65E†
80 17.9 (455) 14 (356) 5CLE-80E†
80 15.9 (404) 12 (305) 5HLE-80E†
100 17.9 (455) 14 (356) 5CLE-100E†
100 15.9 (404) 12 (305) 5HLE-100E†
125 17.9 (455) 14 (356) 5CLE-125E†
125 15.9 (404) 12 (305) 5HLE-125E†
3 (76) Indoor/outdoor
150 17.9 (455) 14 (356) 5CLE-150E†
150 15.9 (404) 12 (305) 5HLE-150E†
65
175 17.9 (455) 14 (356) 5CLE-175E†
175 15.9 (404) 12 (305) 5HLE-175E†
200 17.9 (455) 14 (356) 5CLE-200E†
200 15.9 (404) 12 (305) 5HLE-200E†
250 17.9 (455) 14 (356) 5CLE-250E†
250 15.9 (404) 12 (305) 5HLE-250E†
300 17.9 (455) 14 (356) 5CLE-300E†
300 15.9 (404) 12 (305) 5HLE-300E†
350 17.9 (455) 14 (356) 5CLE-350E†
350 15.9 (404) 12 (305) 5HLE-350E†
2
400 17.9 (455) 14 (356) 5CLE-400E†
400 15.9 (404) 12 (305) 5HLE-400E†
450 17.9 (455) 14 (356) 5CLE-450E†
450 15.9 (404) 12 (305) 5HLE-450E†
* Fuses conform to dimensional standards established by Westinghouse.
† UL Listed, Guide JEEG, File E240398.

Data sheet no. 10351

7-6 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
MV055 full range
Dimensions — in (mm)
Amps Length A Diameter B Clip centers C IR RMS Sym. (kA) No. of Barrels Installation location Catalog no.
5 MV055F1CAX5E
7 2 (51) MV055F1CAX7E
10 MV055F1CAX10E
10 3 (76) MV055F1DAX10E
15 2 (51) MV055F1CAX15E
15 3 (76) MV055F1DAX15E
20 2 (51) MV055F1CAX20E
20 3 (76) MV055F1DAX20E
25 2 (51) MV055F1CAX25E
25 3 (76) MV055F1DAX25E
30 2 (51) MV055F1CAX30E
30 3 (76) MV055F1DAX30E
1
40 2 (51) MV055F1CAX40E
40 3 (76) MV055F1DAX40E
50 15.7 (399) 2 (51) 12 (305) 50 Indoor MV055F1CAX50E
50 3 (76) MV055F1DAX50E
65 2 (51) MV055F1CAX65E
65 MV055F1DAX65E
80 MV055F1DAX80E
100 MV055F1DAX100E
125 MV055F1DAX125E
150 MV055F1DAX150E
175 MV055F1DAX175E
3 (76)
200 MV055F1DAX200E
250 MV055F2DAX250E
300 MV055F2DAX300E
350 2 MV055F2DAX350E
400 MV055F2DAX400E
450 MV055F2DAX450E

Recommended MV055 fuseclips

Description Fuse dia. — in (mm) Catalog no.
2 (51) A3354710*
Enclosed fuseclip
A3354730*
Open fuseclip 3 (76) 1A0065
Spring loaded open fuseclip 9078A67G04

Medium voltage
* For single barrel applications only. Not sold in pairs.

fuses

Data sheet no. 10351

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-7
7 — Medium voltage
A fuses X.XX (XX.X)

5.5B kV E-Rated medium voltage specialty mount HCL clip-lock

fuses 0.44 x 0.91
Slots 0.44 (11.2) Dia. Hole A
Catalog symbols
(11.2 x 23.1) Indicator

•• 5AHLE-_E (for EatonCAMPGARD motor starting assemblies) 0.5 (12.7)

0.25
•• 5BHLE-_E / 5BHCL-_E (bolt-on version) (6.4)
•• 5CLE-_E 4.31 (109.5) 4.31 (109.5)

•• 5HCL-_E (clip-lock version) 1.25 1.25

(31.8) (31.8) B
Ratings*

•• Volts 5.5 kV
•• Amps 10 to 900 A
•• Interrupting ratings 31 to 63 kA RMS Sym.
7.94 (201.7)
7.94 (201.7)
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.

Agency information
0.5 (12.7)
•• E-Rated fuses meet the performance characteristics of ANSI
C37.46

Recommended live parts for clip-lock fuses

11.62 (295.1) 0.38 11.62 (295.1)
•• Catalog number HCL-NL-1
(9.7)
Dimensions — in (mm)
BHLE bolt-on 3.00
Indicator
CLE four-barrel bolt-on
2.12 (76.2)
(53.8) 16.0
* Flush with surface in untripped position, trip force is 2 lb (0.9kg)

B C
A

10.18
Indicator to be
located here
1.19

3.31
(84.1)

20.0
B C
2.12
(53.8) A

Indicator to be
located here

3.31
(84.1) Note: 1100E and 1350E fuses require two double barrel fuses (4
total barrels) customer to parallel.
3.31
(84.1)

B C
2.12
(53.8) A

Data sheet no. 10351

7-8 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
AHLE for Eaton AMPGARD motor starting assemblies
Amps IR RMS Sym. (kA) No. of barrels Catalog no.
10 5AHLE-10E
15 5AHLE-15E
20 5AHLE-20E
25 5AHLE-25E
30 5AHLE-30E
40 5AHLE-40E†
50 5AHLE-50E†
65 1 5AHLE-65E†
80 5AHLE-80E†
100 65 5AHLE-100E†
125 5AHLE-125E†
150 5AHLE-150E†
175 5AHLE-175E†
200 5AHLE-200E†
250 5AHLE-250E†
300 5AHLE-300E†
350 5AHLE-350E†
2
400 5AHLE-400E†
450 5AHLE-450E†
† UL Listed, Guide JEEG, File E240398.

HCL clip-lock versions

Dimensions — in (mm) IR RMS Sym. Installation
Amps Length A Diameter B Hole centers C (kA) No. of barrels location Catalog no.
10 5HCL-10E
15 5HCL-15E
20 5HCL-20E
25 5HCL-25E
30 5HCL-30E
40 5HCL-40E†
16.8 (427)
50 5HCL-50E†
1
65 5HCL-65E†
80 5HCL-80E†
100 3 (76) N/A 65 Indoor 5HCL-100E†
125 5HCL-125E†
150 5HCL-150E†
200 5HCL-200E†

Medium voltage
250 5HCL-250E†

fuses
300 5HCL-300E†
400 22.8 (579) 5HCL-400E†
450 2 5HCL-450E†
500 5HCL-500E
600 5HCL-600E
† UL Listed, Guide JEEG, File E240398.

Data sheet no. 10351

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-9
7 — Medium voltage fuses
CLE, BHLE and BHCL bolt-on versions
Dimensions — in (mm) IR RMS Sym. Installation
Amps Length A Diameter B Hole centers C (kA) No. of barrels location Catalog no.
10 5BHLE-10E
15 5BHLE-15E
20 5BHLE-20E
25 5BHLE-25E
30 5BHLE-30E
40 5BHLE-40E†
50 5BHLE-50E†
19.2 (488) 17.9 (455)
65 5BHLE-65E†
80 1 5BHLE-80E†
100 5BHLE-100E†
125 5BHLE-125E†
150 5BHLE-150E†
175 5BHLE-175E†
3 (76) 65
200 5BHLE-200E†
200 25.1 (637) 23.7 (602) 5BHCL-200E
250 19.2 (488) 17.9 (455) 5BHLE-250E†
Indoor
250 25.1 (637) 23.7 (602) 5BHCL-250E
300 19.2 (488) 17.9 (455) 5BHLE-300E†
300 25.1 (637) 23.7 (602) 5BHCL-300E
350 5BHLE-350E†
19.2 (488) 17.9 (455)
400 5BHLE-400E†
400 25.1 (637) 23.7 (602) 5BHCL-400E
2
450 19.2 (488) 17.9 (455) 5BHLE-450E†
450 5BHCL-450E
500 25.1 (637) 23.7 (602) 5BHCL-500E
600 5BHCL-600E
600 28.9 (734) 4 (102) 18.4 (467) 40 5CLE-600E
750 25.1 (637) 3 (76) 23.7 (602) 63 3 5BHCL-750E
750 28.9 (734) 4 (102) 18.4 (467) 40 2 5CLE-750E
900 25.1 (637) 3 (76) 23.7 (602) 63 3 5BHCL-900E
1100 5CLE-1100E
19.8 (503) 4 (102) 18.4 (467) 31 4
1350 5CLE-1350E
† UL Listed, Guide JEEG, File E240398.

Data sheet no. 10351

7-10 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
8.3 kV E-Rated medium voltage ferrule fuses Dimensions — in (mm)

Catalog symbols C
•• 8CLE-_E-D (10-25 A)
B
•• 8CLE-_E (10-350 A)
•• 8HLE-_E (10-350 A)

Ratings*

•• Volts 8.3 kV
3.31
•• Amps 10 to 350 A (84.1)
•• IR 50 kA RMS Sym. B
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.
A
Agency information

•• E-Rated fuses meet the performance characteristics of ANSI

C37.46
Recommended fuseclips
Description Fuse dia. — in (mm) Catalog no.
2 (51) A3354710*
Enclosed fuseclip
A3354730*
Open fuseclip 3 (76) 1A0065
Spring loaded open fuseclip 9078A67G04

* For single barrel applications only. Not sold in pairs.

Recommended fuse holders

Catalog no.
Approx. dimensions — in (mm) Mounting* Live parts End fittings
Fuse mounting BIL Porcelain Glass-polyester (with end (disconnect
Amps type (kV) Diameter A Clip center B Length C insulator insulator fittings) only)
CLE
10E-D–25E-D Non-disconnect 8CLE-PNM-D 8CLE-GNM-D CLE-NL-D —
30E–175E 3.0 (76) 17.9 (455)
Single barrel Disconnect †
8CLE-PDM-D 8CLE-GDM-D CLE-DL-D CLE-DF-D
15E–25E Non-disconnect 75 14 (356) 8CLE-PNM-C 8CLE-GNM-C CLE-NL-C —
2.0 (51) 15.5 (394)
Single Barrel Disconnect† 8CLE-PDM-C 8CLE-GDM-C CLE-DL-C CLE-DF-C
200E–350E Non-disconnect 8CLE-PNM-E 8CLE-GNM-E CLE-NL-E —
3.0 (76) 17.9 (455)
Double barrel Disconnect 8CLE-PDM-E 8CLE-GDM-E CLE-DL-E CLE-DF-E

Medium voltage
HLE

fuses
10E-175E Non-disconnect 8HLE-PNM-D 8HLE-GNM-D CLE-NL-D —
Single barrel Disconnect† 8HLE-PDM-D 8HLE-GDM-D CLE-DL-D CLE-DF-D
75 3.0 (76) 12 (305) 15.9 (404)
200E–350E Non-disconnect 8HLE-PNM-E 8HLE-GNM-E CLE-NL-E —
Double barrel Disconnect† 8HLE-PDM-E 8HLE-GDM-E CLE-DL-E CLE-DF-E
* Including live parts and end fittings, end fittings supplied only when required.
† Disconnect mountings provide a means for fuse extraction only. Do not use a
disconnect mounting for load switching or fuse removal while energized.

Data sheet no. 10352

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-11
7 — Medium voltage fuses
CLE and HLE Type fuses
Dimensions — in (mm)
Installation
Amps Length A Diameter B Clip centers C IR RMS Sym. (kA) No. of barrels location Catalog no.
CLE Long construction (Westinghouse)
10 17.9 (455) 3 (76) Indoor/outdoor 8CLE-10E-D
15 15.5 (394) 2 (51) Indoor 8CLE-15E*
15 17.9 (455) 3 (76) Indoor/outdoor 8CLE-15E-D
20 15.5 (394) 2 (51) Indoor 8CLE-20E*
20 17.9 (455) 3 (76) Indoor/outdoor 8CLE-20E-D
25 15.5 (394) 2 (51) Indoor 8CLE-25E*
25 8CLE-25E-D
30 8CLE-30E
1
40 8CLE-40E
50 8CLE-50E
14 (356) 50
65 8CLE-65E
80 8CLE-80E
100 8CLE-100E
17.9 (455) 3 (76) Indoor/outdoor
125 8CLE-125E
150 8CLE-150E
175 8CLE-175E
200 8CLE-200E
250 8CLE-250E
2
300 8CLE-300E
350 8CLE-350E
HLE Short construction
10 8HLE-10E
15 8HLE-15E
20 8HLE-20E
25 8HLE-25E
30 8HLE-30E
40 8HLE-40E
50 1 8HLE-50E
65 8HLE-65E
80 15.9 (404) 3 (76) 12 (305) 50 Indoor/outdoor 8HLE-80E
100 8HLE-100E
125 8HLE-125E
150 8HLE-150E
175 8HLE-175E
200 8HLE-200E
250 8HLE-250E
2
300 8HLE-300E
350 8HLE-350E
* Fuses conform to dimensional standards established by Westinghouse.

Data sheet no. 10352

7-12 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
8.3 kV E-Rated medium voltage specialty mount
fuses
Catalog symbols

•• 8AHLE-_E (special dimension fuses for use with 7.2 kV rated,

800 amp AMPGARD motor starting assemblies)
•• 8BHLE-_E (bolt-on version)
•• 8HCL-_E (clip-lock version)

Ratings*

•• Volts 8.3 kV
•• Amps 10 to 350 A
•• Interrupting rating 50 kA RMS Sym.
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.

Agency information

•• E-Rated fuses meet the performance characteristics of ANSI

C37.46

Recommended live parts for clip-lock fuses

•• Catalog number HCL-NL-1

Dimensions for BHLE — in (mm) Dimensions for HCL — in (mm)

A X.XX (XX.X)

B 2.12
(53.8)
0.44 x 0.91
Slots 0.44 (11.2) Dia. Hole A
(11.2 x 23.1) Indicator

C 0.5 (12.7)
B C 0.25
(6.4)
A
4.31 (109.5) 4.31 (109.5)

1.25 1.25
Indicator to be
(31.8) (31.8) B
located here

Medium voltage
3.31
(84.1)

fuses
7.94 (201.7)
7.94 (201.7)

B C
2.12
(53.8) A
0.5 (12.7)

Indicator to be
located here 11.62 (295.1)
11.62 (295.1) 0.38
(9.7)
3.31
(84.1)
Indicator 3.00
3.31
(76.2)
(84.1)
* Flush with surface in untripped position, trip force is 2 lb (0.9kg)

B C
2.12 Data sheet no. 10352
(53.8) A
BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-13
7 — Medium voltage fuses
AHLE Type fuses

Special dimension fuses for use with 7.2 kV rated, 800 amp AMPGARD motor starting assemblies.

Amps IR RMS Sym. (kA) No. of barrels Catalog no.

10 8AHLE-10E
15 8AHLE-15E
20 8AHLE-20E
25 8AHLE-25E
30 8AHLE-30E
40 8AHLE-40E
50 1 8AHLE-50E
65 8AHLE-65E
80 50 8AHLE-80E
100 8AHLE-100E
125 8AHLE-125E
150 8AHLE-150E
175 8AHLE-175E
200 8AHLE-200E
250 8AHLE-250E
2
300 8AHLE-300E
350 8AHLE-350E

BHLE bolt-on versions

Dimensions — in (mm) IR RMS Sym. Installation
Amps Overall length Diameter Hole centers (kA) No. of barrels location Catalog no.
10 8BHLE-10E
15 8BHLE-15E
20 8BHLE-20E
25 8BHLE-25E
30 8BHLE-30E
40 8BHLE-40E
50 1 8BHLE-50E
65 8BHLE-65E
80 19.25 (488.9) 3 (76.2) 17.88 (454.2) 50 Indoor 8BHLE-80E
100 8BHLE-100E
125 8BHLE-125E
150 8BHLE-150E
175 8BHLE-175E
200 8BHLE-200E
250 8BHLE-250E
2
300 8BHLE-300E
350 8BHLE-350E

HCL Clip lock versions

Dimensions — in (mm) Installation
Amps Overall length Diameter Hole centers IR RMS Sym. (kA) No. of barrels location Catalog no.
65 8HCL-65E
80 8HCL-80E
100 8HCL-100E
1
125 8HCL-125E
150 8HCL-150E
22.5 (571.5) 3 (76.2) N/A 50 Indoor/outdoor
175 8HCL-175E
200 8HCL-200E
250 8HCL-250E
2
300 8HCL-300E
350 8HCL-350E

Data sheet no. 10352

7-14 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
15.5 kV E-Rated medium voltage ferrule fuses
Catalog symbols C
•• General purpose
B
•• 15CLE-_E-D (long construction, 10-25 A)
•• 15CLE-_E (long construction, 15-300 A)
•• 15HLE-_E (short construction, 10-250 A)
•• 15LHLE-_E (intermediate construction, 65-300 A)
•• Full range (per ANSI C37.40) 3.31
•• MV155F_ (84.1)
B
Ratings*

•• Volts 15.5 kV A
•• Amps 10 to 300 A
•• Interrupting ratings 31.5 to 63 kA RMS Sym.
Dimensions — in (mm)
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number. Recommended fuseclips

Agency information Description Fuse dia. — in (mm) Catalog no.

2 (51) A3354710*
Enclosed fuseclip
•• E-Rated fuses meet the performance characteristics of ANSI A3354730*
C37.46 Open fuseclip 3 (76) 1A0065
•• UL Listed, Guide JEEG, File E240398. See catalog numbers. Spring loaded open fuseclip 9078A67G04

Recommended fuse holders * For single barrel applications only. Not sold in pairs.

Catalog no.
Approx. dimensions — in (mm) Mounting* Live parts End fittings
Fuse mounting BIL Glass-polyester (with end (disconnect
Amps type (kV) Diameter Clip center Length Porcelain insulator insulator fittings) only)
CLE
95 15CLE-PNM-C 15CLE-GNM-C CLE-NL-C —
Non-disconnect
15E–25E 110 15CLE-HPNM-C — CLE-NL-C —
2 (51) 21.5 (546)
Single barrel 95 15CLE-PDM-C 15CLE-GDM-C CLE-DL-C CLE-DF-C
Disconnect†
110 15CLE-HPDM-C — CLE-DL-C CLE-DF-C
95 15CLE-PNM-D 15CLE-GNM-D CLE-NL-D —
10E-D–25E-D Non-disconnect 110
20 (508)
15CLE-HPM-D — CLE-NL-D —
30E–150E
Single barrel Disconnect† 95 15CLE-PDM-D 15CLE-GDM-D CLE-DL-D CLE-DF-D
3 (76) 23.9 (607)
110 15CLE-HPDM-D — CLE-DL-D CLE-DF-D

Medium voltage
175E–300E Non-disconnect 110 15CLE-PNM-E — CLE-NL-E —
Double barrel Disconnect† 110 15CLE-PDM-E — CLE-DL-E CLE-DF-E

fuses
HLE
10E-125E Non-disconnect 95 15HLE-PNM-D 15HLE-GNM-D CLE-NL-D —
Single barrel Disconnect† 95 15HLE-PDM-D 15HLE-GDM-D CLE-DL-D CLE-DF-D
3 (76) 15 (381) 18.9 (480)
150E–250E Non-disconnect 95 15HLE-PNM-E — CLE-NL-E —
Double barrel Disconnect† 95 15HLE-PDM-E — CLE-DL-E CLE-DF-E
LHLE
65E–150E Non-disconnect — CLE-NL-D —
Single barrel Disconnect† — CLE-DL-D CLE-DF-D
3 (76) 18 (457) 20.53 (521) Not available Not available
175E–300E Non-disconnect — CLE-NL-E —
Double barrel Disconnect† — CLE-DL-E CLE-DF-E
* Including live parts and end fittings, end fittings supplied only when required.
† Disconnect mountings provide a means for fuse extraction only. Do not use a
disconnect mounting for load switching or fuse removal while energized.

Data sheet no. 10353

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-15
7 — Medium voltage fuses
CLE, HLE and LHLE Type general purpose fuses
Dimensions — in (mm) IR RMS Sym. Installation
Amps Length A Diameter B Clip centers C (kA) No. of barrels location Catalog no.
CLE Long construction
10 23.9 (607) 3 (76) 63 Indoor/outdoor 15CLE-10E-D
15 21.5 (546) 2 (51) 31.5 Indoor 15CLE-15E*
15 23.9 (607) 3 (76) 63 Indoor/outdoor 15CLE-15E-D
20 21.5 (546) 2 (51) 31.5 Indoor 15CLE-20E*
20 23.9 (607) 3 (76) 63 Indoor/outdoor 15CLE-20E-D
25 21.5 (546) 2 (51) 31.5 Indoor 15CLE-25E*
25 15CLE-25E-D
30 1 15CLE-30E
40 15CLE-40E†
50 20 (508) 15CLE-50E†
65 15CLE-65E†
80 15CLE-80E†
100 23.9 (607) 3 (76) 63 Indoor/outdoor 15CLE-100E†
125 15CLE-125E†
150 15CLE-150E†
175 15CLE-175E†
200 15CLE-200E†
2
250 15CLE-250E†
300 15CLE-300E†
HLE Short construction
10 15HLE-10E
15 15HLE-15E
20 15HLE-20E
25 15HLE-25E
30 15HLE-30E
40 1 15HLE-40E†
50 15HLE-50E†
65 18.9 (480) 3 (76) 15 (381) 63 Indoor/outdoor 15HLE-65E†
80 15HLE-80E†
100 15HLE-100E†
125 15HLE-125E†
150 15HLE-150E†
175 15HLE-175E†
2
200 15HLE-200E†
250 15HLE-250E†
LHLE
65 15LHLE-65E
80 15LHLE-80E
100 1 15LHLE-100E
125 15LHLE-125E
150 20.5 (521) 3 (76) 18 (457) 50 Indoor/outdoor 15LHLE-150E
175 15LHLE-175E
200 15LHLE-200E
2
250 15LHLE-250E
300 15LHLE-300E
* Fuses conform to dimensional standards established by Westinghouse.
† UL Listed, Guide JEEG, File E240398.

Data sheet no. 10353

7-16 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7

MV155F_ Full range

Dimensions — in (mm) IR RMS Sym. Installation
Amps Length A Diameter B Clip centers C (kA) No. of barrels location Catalog no.
5 MV155F1CBX5E
7 2 (51) MV155F1CBX7E
10 MV155F1CBX10E
10 3 (76) MV155F1DBX10E
15 2 (51) MV155F1CBX15E
15 3 (76) MV155F1DBX15E
20 2 (51) MV155F1CBX20E
20 18.7 (475) 3 (76) 15 (381) MV155F1DBX20E
25 2 (51) MV155F1CBX25E
25 3 (76) MV155F1DBX25E
1
30 2 (51) MV155F1CBX30E
30 MV155F1DBX30E
40 MV155F1DBX40E
50 MV155F1DBX50E
50 Indoor
65 MV155F1DBX65E
65 21.7 (551) 18 (457) MV155F1DCX65E
80 18.7 (475) 15 (381) MV155F1DBX80E
80 21.7 (551) 18 (457) MV155F1DCX80E
100 18.7 (475) 15 (381) MV155F1DBX100E
100 21.7 (551) 3 (76) 18 (457) MV155F1DCX100E
125 18.7 (475) 15 (381) MV155F2DBX125E
125 21.7 (551) 18 (457) MV155F2DCX125E
150 18.7 (475) 15 (381) MV155F2DBX150E
150 21.7 (551) 18 (457) MV155F2DCX150E
2
175 18.7 (475) 15 (381) MV155F2DBX175E
175 21.7 (551) 18 (457) MV155F2DCX175E
200 18.7 (475) 15 (381) MV155F2DBX200E
200 21.7 (551) 18 (457) MV155F2DCX200E

Medium voltage
fuses

Data sheet no. 10353

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-17
7 — Medium voltage fuses
15.5 kV E-Rated medium voltage specialty mount
fuses
Catalog symbols

•• 15BHLE-_E (bolt-on version)

•• 15HCL-_E (clip-lock version)

Ratings*

•• Volts 15.5 kV
•• Amps 10 to 300 A
•• Interrupting ratings 50 to 63 kA RMS Sym.
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.

Agency information

•• E-Rated fuses meet the performance characteristics of ANSI

C37.46

Recommended live parts for clip-lock fuses

•• Catalog number HCL-NL-1

Dimensions — in (mm)
A X.XX (XX.X)
BHLE HCL
B 2.12
(53.8)
0.44 x 0.91
Slots 0.44 (11.2) Dia. Hole A
(11.2 x 23.1) Indicator

C 0.5 (12.7)
B C 0.25
(6.4)
A
4.31 (109.5) 4.31 (109.5)

1.25 1.25
Indicator to be
(31.8) (31.8) B
located here

3.31
(84.1)
7.94 (201.7)
7.94 (201.7)

B C
2.12
(53.8) A
0.5 (12.7)

Indicator to be
located here
11.62 (295.1) 0.38 11.62 (295.1)
(9.7)
3.31
(84.1)
3.31 Indicator 3.00
(84.1) (76.2)

* Flush with surface in untripped position, trip force is 2 lb (0.9kg)

B C
2.12
(53.8) A

Data sheet no. 10353

7-18 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
BHCL, BHLE and HCL Type fuses
Dimensions — in (mm)
IR RMS Sym. Installation
Amps Length A Diameter B Hole centers C (kA) No. of barrels location Catalog no.
BHCL and BHLE bolt-on
10 15BHLE-10E
15 15BHLE-15E
20 15BHLE-20E
25 15BHLE-25E
30 15BHLE-30E
40 1 15BHLE-40E†
50 15BHLE-50E†
65 22.2 (563) 20.9 (531) 63 Indoor/outdoor 15BHLE-65E†
80 3 (76) 15BHLE-80E†
100 15BHLE-100E†
125 15BHLE-125E†
150 15BHLE-150E†
175 15BHLE-175E†
200 2 15BHLE-200E†
250 15BHLE-250E†
300 Indoor 15BHCL-300E
25.1 (637) 23.7 (602) 50
400 3 Indoor 15BHCL-400E
HCL clip-lock
10 15HCL-10E
15 15HCL-15E
20 15HCL-20E
25 15HCL-25E
30 15HCL-30E
40 1 15HCL-40E†
50 15HCL-50E†
65 15HCL-65E†
22.8 (579) 3 (76) N/A 63 Indoor
80 15HCL-80E†
100 15HCL-100E†
125 15HCL-125E†
150 15HCL-150E†
175 15HCL-175E†
200 2 15HCL-200E†
250 15HCL-250E†
300 15HCL-300E†

Medium voltage
† UL Listed, Guide JEEG, File E240398.

fuses

Data sheet no. 10353

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-19
7 — Medium voltage fuses
5.5 to 38 kV E-Rated DIN medium voltage fuses
Bussmann series DIN dimensioned E-Rated medium voltage power
fuses with striker for indoor use. Available in general purpose (5.5 to
17.5 kV) and full range (25.8 to 38 kV) versions.

Ratings

•• Volts 5.5 - 38 kV
•• Amps 10 - 450 A
•• Interrupting ratings 25 to 65 kA

Agency information

•• General purpose E-Rated per ANSI C37.46 (5.5 to 17.5 kV)

•• Full range E-Rated per ANSI C37.40 (25.8 to 38 kV)

Striker force

•• 50 N (11 lbs)

Recommended fuseclips

See page 7-36 for dimensions.

Amp range Description Catalog no.

Enclosed fuseclip with wingnut A3354745*
Up to 200 A tensioner
Open fuseclip with spring tensioner 270303
* Not sold in pairs.

Features

•• Cool running for lower watts loss

•• 100% X-ray inspected to help assure fuse integrity
•• Striker provides visual indication of fuse operation or a means to
activate a remote monitoring system

Typical applications

•• Primary protection for medium voltage transformers and switch

gear
•• Protection of medium voltage feeder circuits
•• Direct OEM replacement fuses for 600 A Square D HVLCC and
HVL switches

Dimensions — in (mm)

Striker in operated position

(striker force 50 N/11 Lbs)

1.77 0.59
Diameter
(45) (15)

1.34 1.02
Length
(34) (26)
See catalog numbers tables for diameter and length values.

Data sheet no. 10638

7-20 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
Dimensions — in (mm)
Catalog no. Amps Interrupting rating (Sym. kA) Length Diameter
General purpose versions
5.5 kV
55GDMSJ10E 10
55GDMSJ15E 15
55GDMSJ20E 20
55GDMSJ25E 25
55GDMSJ30E 30
55GDMSJ40E 40 17.4 (442) 2 (51)
55GDMSJ50E 50
55GDMSJ65E 65
55GDMSJ80E 80
55GDMSJ100E 100 65
55GDMSJ125E 125
55GFMSJ150E 150
55GFMSJ175E 175
55GFMSJ200E 200
55GFMSJ250E 250
17.4 (442) 3 (76)
55GFMSJ300E 300
55GFMSJ350E 350
55GFMSJ400E 400
55GFMSJ450E 450
15.5 kV
155GXQSJ175E 175
65 21.1 (537) 3.5 (89)
155GXQSJ200E 200
17.5 kV
175GDMSJ10E 10
175GDMSJ15E 15
175GDMSJ20E 20 17.4 (442) 2 (51)
175GDMSJ25E 25
175GDMSJ30E 30
175GFMSJ40E 40
65
175GFMSJ50E 50 17.4 (442) 3 (76)
175GFMSJ65E 65
175GXMSJ80E 80
17.4 (442) 3.5 (89)
175GXMSJ100E 100
175GXQSJ125E 125
21.1 (537) 3.5 (89)
175GXQSJ150E 150
Full range versions

Medium voltage
25.8 kV
258GDQSJ10E 10

fuses
258GDQSJ15E 15
258GDQSJ20E 20 21.1 (537) 2 (51)
258GDQSJ25E 25
258GDQSJ30E 30
25
258GXQSJ40E 40
258GXQSJ50E 50 21.1 (537) 3.5 (89)
258GXQSJ65E 65
258GXZSJ80E 80
28.3 (718) 3.5 (89)
258GXZSJ100E 100
38 kV
38GFZSJ10E 10
38GFZSJ15E 15
38GFZSJ20E 20 25 28.3 (718) 3 (76)
38GFZSJ25E 25
38GFZSJ30E 30

Data sheet no. 10638

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-21
7 — Medium voltage fuses
2.4 kV R-Rated fuses Dimensions — in (mm)

Catalog symbols/construction Dimension

Construction Amps A B C D
•• JCK-_R/Standard
Standard - 25-230A —
•• 2CLS-_R/Standard short 390-450A 3.3 (84)
•• JCK-A-_R*/AMPGARD Hookeye 10.8 (274) 3 (76)
AMPGARD 70-230A —
3 (76)
•• 2ACLS-_R/AMPGARD Hookeye Hookeye* 390-450A 3.3 (84)
•• JCH-_R/Hermetically sealed AMPGARD 25-230A —
Bolt-on 19.2 (488) 17.9 (455)
•• 2HCLS-_R/Hermetically sealed AMPGARD 390-450A 3.3 (84)
•• JCK-B-_R/Bolt-on * Includes hermetically sealed versions.
•• 2BCLS-_R/Bolt-on
* For use in 400 amp AMPGARD motor starters. Standard and AMPGARD Hookeye
Ratings
Gripping tab
•• Volts for Hookeye
•• 2.4 kV (nominal) constructions only Indicator
D
•• 2.54 kV (max design)
C
•• Amps 25-450 A
•• Interrupting ratings B
A
•• 50 kA Sym.

•• 80 kA Asym.

Agency information Bolt-on

R 0.23 [5.81] Typ.
EFGHI
•• UL Recognized: Guide MSSS2, File E96676 (JCK-_R [2R-12R] and E = 3 [76.2]
F = 2.5 [63.5]
JCK-A-_R [2R-12R]) G = 2.04 [51.81
H = 0.96 [24.4]
I = 0.5 [12.7]
Recommended fuseclips and holders for standard D Indicator
constructions C
2.12
[53.8]
Amps Description Catalog no.
Fuseclips 3.0 3.0
B
[76.2] [76.2] A
25-230A 3” Enclosed fuseclip* A3354730
3” Open fuseclip 1A0065
25-450A
3” Spring loaded open fuseclip 9078A67G04
Fuse holders
Non-disconnect holder, porcelain 2CLE-PNM-D
25-230A Non-disconnect holder, glass polyester 2CLE-GNM-D
Single barrel Disconnect holder, porcelain 2CLE-PDM-D
Disconnect holder, glass polyester 2CLE-GDM-E
Non-disconnect holder, porcelain 2CLE-PNM-E
390-450A Non-disconnect holder, glass polyester 2CLE-GNM-E
Double
barrel Disconnect holder, porcelain 2CLE-PDM-E
Disconnect holder, glass polyester 2CLE-GDM-E
* Single barrel only, not sold in pairs.

2.4 kV R-Rated fuse catalog numbers

"R" Mounting style (minimum interrupting rating in amps) No. of
Amps Des. Standard Standard AMPGARD Hermetically sealed AMPGARD Bolt-on barrels
25 — — 2CLS-25* (100) — 2ACLS-25* (90) JCH-30* (90) 2HCLS-25* (90) JCK-B-25* (90) 2BCLS-25* (90)
70 2R JCK-2R (165) 2CLS-2R (180) JCK-A-2R (165) 2ACLS-2R (180) JCH-2R (180) 2HCLS-2R (180) JCK-B-2R (180) 2BCLS-2R (180)
100 3R JCK-3R (220) 2CLS-3R (270) JCK-A-3R (220) 2ACLS-3R (270) JCH-3R (270) 2HCLS-3R (270) JCK-B-3R (270) 2BCLS-3R (270)
130 4R JCK-4R (320) 2CLS-4R (360) JCK-A-4R (320) 2ACLS-4R (360) JCH-4R (360) 2HCLS-4R (360) JCK-B-4R (360) 2BCLS-4R (360)
1
150 5R JCK-5R (410) 2CLS-5R (450) JCK-A-5R (410) 2ACLS-5R (450) JCH-5R (450) 2HCLS-5R (450) JCK-B-5R (450) 2BCLS-5R (450)
170 6R JCK-6R (480) 2CLS-6R (540) JCK-A-6R (480) 2ACLS-6R (540) JCH-6R (540) 2HCLS-6R (540) JCK-B-6R (540) 2BCLS-6R (540)
200 9R JCK-9R (720) 2CLS-200* (740) JCK-A-9R (720) 2ACLS-200* (740) JCH-200* (740) 2HCLS-200* (740) JCK-B-200* (740) 2BCLS-200* (740)
230 12R JCK-12R (970) 2CLS-230* (1080) JCK-A-12R (970) 2ACLS-230* (1080) JCH-230* (1080) 2HCLS-230* (1080) JCK-B-230* (1080) 2BCLS-230* (1080)
390 18R JCK-18R (1430)† 2CLS-390* (1500) JCK-A-18R (1430)† 2ACLS-390* (1500) JCH-390* (1500) 2HCLS-390* (1500) JCK-B-390* (1500) 2BCLS-390* (1500)
2
450 24R JCK-24R (1880)† 2CLS-450* (2200) JCK-A-24R (1880)† 2ACLS-450* (2200) JCH-450* (2200) 2HCLS-450* (2200) JCK-B-450* (2200) 2BCLS-450* (2200)
* Does not comply with ANSI C37.46 for “R” rating.
† Not UL Recognized.

Data sheet no. 6001

7-22 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
4.8 kV R-Rated fuses Dimensions — in (mm)

Catalog symbols/construction Dimension

Construction Amp A B C D
•• 5CLS-30 and 5CLS-_R/Standard - short (30 A, 2R-24R)
30-230 —
•• JCL-_R/Standard - short (2R - 24R) Standard - short 15.6 (396)
390-450 3.3 (84)
•• 5LCLS-_R/Standard - long (2R - 24R) 70-230 —
Standard - long 17.8 (452) 3 (76)
•• 5ACLS-30 and 5ACLS-_R/AMPGARD Hookeye* (30 A, 2R-24R) 390-450 3.3 (84)
3 (76)
•• JCL-A-_R/AMPGARD Hookeye* (2R - 24R) AMPGARD 30-230 —
15.6 (396)
Hookeye* 390-450 3.3 (84)
•• 5HCLS-30 and 5HCLS-_R/Hermetically sealed AMPGARD
Hookeye* (30 A, 2R-24R) 30-230 —
•• 5BCLS-30 and 5BCLS-_R/Bolt-on (30 A, 2R-44R) Bolt-on 390-450 19.2 (488) 17.9 (455) 3.3 (84)
600-800 4 (101) 9 (229)
•• JCL-B-_R/Bolt-on (2R-24R)
70-230 4.8 (122)
•• 5MCLS-_R-_A and 5MCLS-_R-_B/Bolt-on GE Limitamp (2R- 24R) Limitamp (-A)
390-450 7.4 (188)
* For use in 400 amp AMPGARD motor starters 18.3 (465) 18.8 (478) 1.4 (36)
70-230 3.0 (76)
Limitamp (-B)
Ratings 390-450 2.4 (61)

* Includes hermetically sealed versions.

•• Volts
•• 4.8 kV (nominal)
Ferrule JCL, 5LCLS, 5CLS and AMPGARD Hookeye

•• 5.0 kV (max design)

Gripping tab
•• Amps 30-800 A for Hookeye
constructions only Indicator
D
•• Interrupting ratings
C
•• 50 kA Sym.
•• 80 kA Asym. B
A
Bolt-on — 5BCLS-_
Agency information
R 0.23 [5.81] Typ.
EFGHI
•• UL Recognized, Guide MSSS2 E = 3 [76.2]
F = 2.5 [63.5]
G = 2.04 [51.81

•• File E96676: JCL-_R [2R-12R], JCL-A-_R [2R-12R], H = 0.96 [24.4]

I = 0.5 [12.7]
D
5MCLS-_R-A [2R-24R], and 5MCLS-_R-B [2R-24R] Indicator

C
•• File E60757: 5CLS-30, 5CLS-_R [2R-18R], 5ACLS-30, and 2.12
[53.8]
5ACLS-_R [2R-24R]
B
3.0 3.0
[76.2] [76.2] A
Recommended fuseclips and holders for standard
constructions Bolt-on — 5MCLS-_R-A
2 SLOTS (0.38X0.5)
17.7 (striker not extended)
0.25 C 16.5

BIL 0.25
0.25

Amps Description (kV) Catalog no.

Fuseclips
30-230A 3” Enclosed fuseclip* A3354730 D

Medium voltage
3.1
3” Open fuseclip — 1A0065 7.75

30-450A
3” Spring loaded open fuseclip 9078A67G04

fuses
2.25
Fuse holders for CLS / JCL / 5HCLS Ø3.0 (REF)

Non-disconnect holder, porcelain 5HLE-PNM-D 2.250 A

30-230A Non-disconnect holder, glass polyester 5HLE-GNM-D B 2 SLOTS
Single (.343 X .875)

barrel Disconnect holder, porcelain 5HLE-PDM-D

C
Disconnect holder, glass polyester 5HLE-GDM-D
60
Non-disconnect holder, porcelain 5HLE-PNM-E
390-450A Non-disconnect holder, glass polyester 5HLE-GNM-E Bolt-on — 5MCLS-_R-B
Double
barrel Disconnect holder, porcelain 5HLE-PDM-E 17.7 (striker not extended)
0.25 16.5
Disconnect holder, glass polyester 5HLE-GDM-E Ø3.00 REF 0.25 0.25

Fuse holders for 5LCLS†

Non-disconnect holder, porcelain 5CLE-PNM-D
Non-disconnect holder, glass polyester 5CLE-GNM-D 3.1

70-230A 60 7.01

Disconnect holder, porcelain 5CLE-PDM-D

Single
barrel Disconnect holder, glass polyester 5CLE-GDM-D D 2.25

Disconnect holder, porcelain 8CLE-PDM-D 0.38

75
Disconnect holder, glass polyester 8CLE-GDM-D 2.25
A
B

390-450A Disconnect holder, porcelain 5CLE-PDM-E

2 SLOTS (0.38X0.5)
2 SLOTS
(0.343X0.875)
Double 60
Barrel Disconnect holder, glass polyester 5CLE-GDM-E C C

* Single barrel only, not sold in pairs.

** Not available for standard - long constructions
† Not available for 390 to 450 amp ratings.
Data sheet no. 6001
BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-23
7 — Medium voltage fuses
4.8 kV R-Rated fuse catalog numbers
Ferrule constructions (min. interrupting rating in amps) No. of Bolt-on (min. interrupting rating in amps) No. of
Amps Short Short Long barrels Amps Regular Regular barrels
30 5CLS-30* (100) — — 30 5BCLS-30* (100)† —
70 5CLS-2R (180) JCL-2R (165) 5LCLS-2R (180)† 70 5BCLS-2R (180)† JCL-B-2R (165)†
100 5CLS-3R (270) JCL-3R (220) 5LCLS-3R (270)† 100 5BCLS-3R (270)† JCL-B-3R (220)†
130 5CLS-4R (360) JCL-4R (320) 5LCLS-4R (360)† 130 5BCLS-4R (360)† JCL-B-4R (320)†
1 1
150 5CLS-5R (450) JCL-5R (410) 5LCLS-5R (450)† 150 5BCLS-5R (450)† JCL-B-5R (410)†
170 5CLS-6R (540) JCL-6R (480) 5LCLS-6R (540)† 170 5BCLS-6R (540)† JCL-B-6R (480)†
200 5CLS-9R (740) JCL-9R (720) 5LCLS-9R (740)† 200 5BCLS-9R (740)† JCL-B-9R (720)†
230 5CLS-12R (1080) JCL-12R (970) 5LCLS-12R (1080)† 230 5BCLS-12R (1080)† JCL-B-12R (970)†
390 5CLS-18R (1500) JCL-18R (1430)† 5LCLS-18R (1500)† 390 5BCLS-18R (1500)† JCL-B-18R (1430)†
2
450 5CLS-24R (2200)† JCL-24R (1880)† 5LCLS-24R (2200)† 450 5BCLS-24R (2200)† JCL-B-24R (1880)†
* Does not comply with ANSI C37.46 for "R" rating. 600 5BCLS-32R (3000)† — 2
† Not UL Recognized. 650 5BCLS-36R (3200)† —
800 5BCLS-44R (3600)† —
AMPGARD Hookeye (min. interrupting rating in amps) No. of
* Does not comply with ANSI C37.46 for "R" rating.
Amps Hookeye Hookeye Hermetic seal barrels
† Not UL Recognized.
30 5ACLS-30* (100) — 5HCLS-30* (100)†
70 5ACLS-2R (180) JCL-A-2R (165) 5HCLS-2R (180)† GE Limitamp (min. interrupting rating in amps) No. of
100 5ACLS-3R (270) JCL-A-3R (220) 5HCLS-3R (270)† Amps Bolt-on Bolt-on barrels
130 5ACLS-4R (360) JCL-A-4R (320) 5HCLS-4R (360)† 30 — —
1
150 5ACLS-5R (450) JCL-A-5R (410) 5HCLS-5R (450)† 70 5MCLS-2R-A (180) 5MCLS-2R-B (180)
170 5ACLS-6R (540) JCL-A-6R (480) 5HCLS-6R (540)† 100 5MCLS-3R-A (270) 5MCLS-3R-B (270)
200 5ACLS-9R (740) JCL-A-9R (720) 5HCLS-9R (740)† 130 5MCLS-4R-A (360) 5MCLS-4R-B (360)
1
230 5ACLS-12R (1080) JCL-A-12R (970) 5HCLS-12R (1080)† 150 5MCLS-5R-A (450) 5MCLS-5R-B (450)
390 5ACLS-18R (1500) JCL-A-18R (1430)† 5HCLS-18R (1500)† 170 5MCLS-6R-A (540) 5MCLS-6R-B (540)
2
450 5ACLS-24R (2200) JCL-A-24R (1880)† 5HCLS-24R (2200)† 200 5MCLS-9R-A (850) 5MCLS-9R-B (850)
* Does not comply with ANSI C37.46 for "R" rating. 230 5MCLS-12R-A (1150) 5MCLS-12R-B (1150)
† Not UL Recognized. 390 5MCLS-18R-A (1725) 5MCLS-18R-B (1725)
2
450 5MCLS-24R-A (2350) 5MCLS-24R-B (2350)
* Does not comply with ANSI C37.46 for "R" rating.
† Not UL Recognized.

5CLS, JCL, JCL-A, 5ACLS and 5HCLS Type mountings — in (mm)

Hole centers BIL

Catalog no. A B Overall length C Hole inset D Hole ctr. E Contact hgt. F Overall hgt. G (kV)
Disconnect single barrel†
5CLE-GDM-D
15.24 (387.1) 25 (647.7)
5CLE-PDM-D
6 (152.4) 0.62 (15.7) 1.75 (44.4) 4.5 (114.3) 11.72 (297.7) 60
5HLE-PDM-D
16.25 (412.8) 23 (584.2)
5HLE-GDM-D
Disconnect double barrel†
5CLE-GDM-E
15.24 (387.1) 25 (647.7)
5CLE-PDM-E
6 (152.4) 0.62 (15.7) 1.75 (44.4) 4.5 (114.3) 15.28 (388.1) 60
5HLE-GDM-E
16.25 (412.8) 23 (584.2)
5HLE-PDM-E
Non-disconnect single barrel
5CLE-GNM-D
15.24 (387.1) 25 (635.0)
5CLE-PNM-D
6 (152.4) 0.62 (15.7) 1.75 (44.4) 4.5 (114.3) 8.79 (223.3) 60
5HLE-GNM-D
16.25 (412.7) 23 (584.2)
5HLE-PNM-D
Non-disconnect double barrel
5HLE-PNM-E
16.25 (412.7) 6 (152.4) 25 (635.0) 0.62 (15.7)\ 1.75 (44.4) 4.5 (114.3) 12.48 (317.0) 60
5HLE-GNM-E

Data sheet no. 6001

7-24 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
7.2 kV R-Rated fuses Dimensions — in (mm)
Dimension
Catalog symbols/construction Construction Amps A B C
Standard
•• 8CLS-_R/Standard (2R - 6R) 15.8 (401) 3 (76)
AMPGARD Hookeye 70-170 3 (76)
•• 8ACLS-_R/AMPGARD Hookeye* (2R - 6R) Bolt-on 19.2 (488) 17.9 (455)
•• 7BCLS-_R/Bolt-on (2R - 6R)
Standard and AMPGARD Hookeye
* For use in 400 amp AMPGARD motor starters.
Gripping tab
Ratings for Hookeye
constructions Indicator
•• Volts
•• 7.2 kV (nominal) C
•• 8.3 kV (max design 70-170 A standard and AMPGARD Hookeye)
7.2 kV (max design 70-170 A bolt-on) B
•• A
•• Amps 70-170 A
•• Interrupting ratings
•• 50 kA Sym. Bolt-on

•• 80 kA Asym. R 0.23 [5.81] Typ.

EFGHI
E = 3 [76.2]
Recommended fuseclips and holders for standard F = 2.5 [63.5]
G = 2.04 [51.81
constructions H = 0.96 [24.4]
I = 0.5 [12.7]
Amps Description BIL (kV) Cat. No. Indicator
Fuseclips
3” Enclosed fuseclip* A3354730 C
2.12
70-170 3” Open fuseclip — 1A0065 [53.8]
3” Spring loaded open fuseclip 9078A67G04
Fuse holders for 7CLS and 8CLS B
3.0
A
Non-disconnect holder, porcelain 8HLE-PNM-D [76.2]

Non-disconnect holder, glass polyester 8HLE-GNM-D

70-170 75
Disconnect holder, porcelain 8HLE-PDM-D
Disconnect holder, glass polyester 8HLE-GDM-D

* Single barrel only, not sold in pairs.

7.2 kV R-Rated fuse catalog numbers

Mounting style (minimum interrupting rating in amps)
Amps “R” Designation Standard AMPGARD Hookeye Bolt-on No. of barrels
70 2R 8CLS-2R (160) 8ACLS-2R (160) 7BCLS-2R (160)
100 3R 8CLS-3R (250) 8ACLS-3R (250) 7BCLS-3R (250)

Medium voltage
130 4R 8CLS-4R (325) 8ACLS-4R (325) 7BCLS-4R (325) 1
150 5R 8CLS-5R (390) 8ACLS-5R (390) 7BCLS-5R (390)

fuses
170 6R 8CLS-6R (500) 8ACLS-6R (500) 7BCLS-6R (500)

Data sheet no. 6001

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-25
7 — Medium voltage fuses
E-Rated PT medium voltage fuses Dimensions — in (mm)

Catalog symbols (by maximum voltage rating) Recommended fuseclip and block
•• 2.475 kV •• 12 kV Description Catalog no.
•• 2NCLPT-_ •• 12ABCNA_ Open fuseclip for 0.8 (20 mm) dia. fuses 1A1837
Single-pole open fuse block with #10-32 phil-slot
•• 3.6 kV •• 12CAV_ screw terminals rated 2500 V, 5 A maximum and PTFB-2500-JCD
•• 3.6ABCNA_ •• 15.5 kV 63 kA withstand rating

•• 3.6ABWNA_ •• 15CLPT-_E
•• 3.6CAV_ •• 15NCLPT-_E-A
•• 5.5 kV •• 15NCLPT-_E-B
•• JCW-_ •• 15.5CAV_E
•• 5CLPT-_E •• 15.5CAVH_E
•• 5NCLPT-_E •• 17.5 kV
•• 5NCLPT-_E-A •• 17.5ABGNA_
•• 5.5ABWNA_E •• 17.5CAV_
•• 5.5AMWNA_E •• 24 kV
•• 5.5CAV_E •• 24ABGNA_
•• 5.5CAVH_E •• 24CAV_
•• 7.2 kV •• 25.5 kV
•• 7.2ABWNA_ •• 25CLPT-_E
•• 7.2ABCNA_ •• 36 kV
•• 7.2AMWNA_E •• 36ABGNA_
•• 7.2CAV_ •• 36CAV_
•• 8.3 kV •• 38 kV
•• 8CLPT-_E-A •• 38CAV_E
•• 8NCLPT-_E •• 38CAVH_E
•• 8NCLPT-_E-A •• 38CLPT-_E
•• 8NCLPT-_E-B

Ratings*

•• Volts 2.4 kV to 38 kV
•• Amps 0.25 to 15 A
•• Interrupting ratings 25 to 80 kA RMS Sym.
* See catalog number tables for voltages, ampacities and interrupting ratings by
catalog number.

Agency information

•• PT fuses conforming to the requirements for E-Rating meet the

performance characteristics of IEEE/ANSI C37.46

Data sheet no. 6002

7-26 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
2.475 to 38 kV PT E-Rated fuses

Dimensions — in (mm) Catalog no. (IR - kA)

Recommended
Amps Length A Diameter B Clip centers C Indicating Non-indicating fuseclip
2.475 kV maximum system voltage
0.25 — 2NCLPT-.25E (63)
0.5 — 2NCLPT-.5E (63)
1 4.5 (114) 0.8 (20) 3.9 (99) — 2NCLPT-1E (40) 1A1837
2 — 2NCLPT-2E (40)
5 — 2NCLPT-5E (25)
3.6 kV maximum system voltage
2 8.7 (221) 1.6 (41) 7.6 (193) — 3.6CAV2 (50) 1A1837
3.15 5.6 (142) 4.4 (112) — 3.6ABWNA3.15 (50)
3.15 7.7 (195) 6.5 (165) — 3.6ABCNA3.15 (50)
6.3 5.6 (142) 1 (25) 4.4 (112) — 3.6ABWNA6.3 (50) A3354705
6.3 — 3.6ABCNA6.3 (50)
7.7 (195) 6.5 (165)
10 — 3.6ABCNA10 (50)
5.5 kV maximum system voltage
0.5 0.8 (20) 4.8 (122) — 5.5AMWNA0.5E (50) 1A1837
5.6 (142)
0.5 1 (25) 4.4 (112) — 5.5ABWNA0.5E (50) A3354705
0.5 7.4 (188) 1.6 (41) 6.2 (157) 5.5CAVH0.5E (50) JCW-1/2E (40) 1A0835
0.5 9.5 (241) 1.6 (41) 8.1 (206) 5CLPT-.5 (50)†
5NCLPT-.5E-A (50) 1A0835
1 1 (25) 4.4 (112) — 5.5ABWNA1E (50) A3354705
5.6 (142)
1 0.8 (20) 4.8 (122) — 5.5AMWNA1.0E (50) 1A1837
1 7.4 (188) 6.2 (157) 5.5CAVH1E (50) JCW-1E (40)
1 1.6 (41) 5CLPT-1 (50)† 5NCLPT-1E-A (50) 1A0835
9.5 (241) 8.1 (206)
1.5 5CLPT-1.5 (50) †
—
2 1 (25) 4.4 (112) — 5.5ABWNA2E (50) A3354705
2 5.6 (142) 8.1 (206) — 5NCLPT-2E (50)
0.8 (20) 1A1837
2 4.8 (122) — 5.5AMWNA2.0E (50)
2 7.4 (188) 1.6 (41) 6.2 (157) 5.5CAVH2E (50) JCW-2E (40) 1A0835
3 1 (25) 4.4 (112) — 5.5ABWNA3E (50) A3354705
5.6 (142)
3 0.8 (20) 4.8 (122) — 5.5AMWNA3.0E (50) 1A1837
3 9.5 (241) 8.1 (206) 5CLPT-3E (50) 5NCLPT-3E (50)
1.6 (41) 1A0835
3 7.4 (188) 6.2 (157) — JCW-3E (40)

Medium voltage
4 5.6 (142) 0.8 (20) 4.8 (122) — 5.5AMWNA4.0E (50) 1A1837

fuses
5 9.5 (241) 1.6 (41) 8.1 (206) 5CLPT-5E (50) 5NCLPT-5E-A (50) 1A0835
5 1 (25) 4.4 (112) — 5.5ABWNA5E (50) A3354705
5.6 (142)
5 0.8 (20) 4.8 (122) — 5.5AMWNA5.0E (50) 1A1837
5 7.3 (185) 5.9 (150) — JCW-5E (40)
10 9.5 (241) 1.6 (41) 8.1 (206) 5CLPT-10E (50) 5NCLPT-10E (50) 1A0835
15 7.4 (188) 6.2 (157) — 5.5CAV15E (50)
† Due to manufacturing variations, this fuse does not comply with ANSI C37.46 for "E" rating.

Data sheet no. 6002

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-27
7 — Medium voltage fuses
2.475 to 38 kV PT E-Rated fuses

Dimensions — in (mm) Catalog no. (IR - kA)

Recommended
Amps Length A Diameter B Clip centers C Indicating Non-indicating fuseclip
7.2 kV maximum system voltage
0.5 7.2AMWNA0.5E (50)
1 5.6 (142) 0.8 (20) 4.8 (122) 7.2AMWNA1.0E (50) 1A1837
2 7.2AMWNA2.0E (50)
2 8.7 (221) 1.6 (41) 7.5 (190) 7.2CAV2 (40) 1A0835
3 5.6 (142) 0.8 (20) 4.8 (122) 7.2AMWNA3.0E (50) 1A1837
3.15 5.6 (142) 4.4 (112) 7.2ABWNA3.15 (45)
1 (25.4) A3354705
3.15 7.7 (195) 6.5 (165) 7.2ABCNA3.15 (45)
—
4 5.6 (142) 0.8 (20) 4.8 (122) 7.2AMWNA4.0E (50) 1A1837
4 8.7 (221) 1.6 (41) 7.5 (190) 7.2CAV4 (40) 1A0835
5 5.6 (142) 0.8 (20) 4.8 (122) 7.2AMWNA5E (50) 1A1837
6 8.7 (221) 1.6 (41) 7.5 (190) 7.2CAV6 (40) 1A0835
6.3 5.6 (142) 4.4 (112) 7.2ABWNA6.3 (45)
1 (25.4) A3354705
6.3 7.7 (195) 6.5 (165) 7.2ABCNA6.3 (45)
10 8.7 (221) 1.6 (41) 7.5 (190) 7.2CAV10 (40) 1A0835
8.3 kV maximum system voltage
0.5 9.5 (241) 1.6 (41) 8.1 (206) 8CLPT-.5 (50)† 8NCLPT-.5E-A (50) 1A0835
1 5 (127) 1.1 (28) 4 (102) 8NCLPT-1E (50) A3354705
1 9.5 (241) 1.6 (41) 8.1 (206) 8NCLPT-1E-A (50) 1A0835
—
2 8 (203) 0.8 (20) 7.2 (183) 8NCLPT-2E (25) 1A1837
2 9.5 (241) 8.1 (206) 8NCLPT-2E-A (50)
1.6 (41) 1A0835
3 12.9 (328) 11.5 (292) 8CLPT-3E (50) 8NCLPT-3E-B (50)
4 8 (203) 0.8 (20) 7.2 (183) 8NCLPT-4E (25) 1A1837
—
5 5 (127) 1.1 (28) 4 (102) 8NCLPT-5E (50) A3354705
5 12.9 (328) 1.6 (41) 11.5 (292) 8CLPT-5E (50) 8NCLPT-5E-B (50) 1A0835
8 5 (127) 1.1 (28) 4 (102) — 8NCLPT-8E A3354705
10 12.9 (328) 1.6 (41) 11.5 (292) 8CLPT-10E (50) 8NCLPT-10E-B (50) 1A0835
12 kV maximum system voltage
2 8.7 (221) 1.6 (41) 7.5 (190) 12CAV2 (40) 1A0835
—
3.15 7.7 (195) 1 (25) 6.5 (165) 12ABCNA3.15 (45) A3354705
15.5 kV maximum system voltage
0.5 12.9 (328) 11.5 (292) 15.5CAVH0.5E (80) 15NCLPT-.5E-A (50)
1 12.9 (328) 11.5 (292) 15.5CAVH1E (80) 15NCLPT-1E-A (50)
2 12.9 (328) 11.5 (292) 15.5CAVH2E (80) 15NCLPT-2E (50)
3 12.9 (328) 11.5 (292) — 15.5CAV3E (80)
3 17.6 (447) 16.1 (409) — 15NCLPT-3E (50)
1.6 (41) 1A0835
3 17.6 (447) 16.1 (409) 15CLPT-3E (50) —
5 12.9 (328) 11.5 (292) — 15.5CAV5E (80)
5 17.6 (447) 16.1 (409) 15CLPT-5E (50) 15NCLPT-5E (50)
7 12.9 (328) 11.5 (292) — 15.5CAV7E (80)
10 17.6 (447) 16.1 (409) 15CLPT-10E (50) 15NCLPT-10E (50)
17.5 kV maximum system voltage
2 17.5CAV2 (40)
4 17.5CAV4 (40)
8.7 (221) 1.6 (41) 7.5 (190) — 1A0835
6 17.5CAV6 (40)
10 17.5CAV10 (40)
† Does not comply with ANSI C37.46 for "E" rating.

Data sheet no. 6002

7-28 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
2.475 to 38 kV PT E-Rated fuses

Dimensions — in (mm) Catalog no. (IR - kA)

Recommended
Amps Length A Diameter B Clip centers C Indicating Non-indicating fuseclip
24 kV maximum system voltage
2 — 24CAV2 (40)
3 13.49 (340) 1.6 (41) 12.2 (310) — 24CAV3 (40) 1A0835
4 — 24CAV4 (40)
25.5 kV maximum system voltage
0.5 25CLPT-.5 (43.5)† —
17.6 (447) 1.6 (41) 16.1 (410) 1A0835
1 25CLPT-1 (43.5) †
—
36 kV maximum system voltage
2 — 36CAV2 (40)
17.3 (439) 1.6 (41) 16.1 (410) 1A0835
4 — 36CAV4 (40)
38 kV maximum system voltage
0.5 17.3 (439) 16.1 (409) 38CAVH0.5E (40) —
0.5 18.6 (472) 17.1 (434) 38CLPT-0.5 (43.5)† —
1 1.6 (41) 38CAVH1E (40) — 1A0835
2 17.3 (439) 16.1 (409) 38CAVH2E (40) —
4 — 38CAV4E (40)
† Does not comply with ANSI C37.46 for “E” rating.

CLPT Type mountings and hardware

Catalog no.
Mounting (including live parts, end fittings)**
Fuse mounting BIL Live parts End fittings
Amps type* (kV) Porcelain insulator Glass-polyester insulator (including end fittings)*** (disconnect only)
5.5 kV maximum (4.8 kV nominal)†
Non-disconnect 5CLPT-PNM-A 5CLPT-GNM-A CLPT-NL —
0.5–10 60
Disconnect ††
5CLPT-PDM-A 5CLPT-GDM-A CLPT-DL CLPT-DF
8.3 kV maximum (7.2 kV nominal)†
Non-disconnect 8CLPT-PNM-A 8CLPT-GNM-A CLPT-NL —
0.5–2
Disconnect†† 8CLPT-PDM-A 8CLPT-GDM-A CLPT-DL CLPT-DF
75
Non-disconnect 8CLPT-PNM-B 8CLPT-GNM-B CLPT-NL —
3–10
Disconnect†† 8CLPT-PDM-B 8CLPT-GDM-B CLPT-DL CLPT-DF
15.5 kV maximum (14.4 kV nominal)

Medium voltage
Non-disconnect 15CLPT-PNM-A 15CLPT-GNM-A CLPT-NL —
0.5–2

fuses
Disconnect†† 15CLPT-PDM-A 15CLPT-GDM-A CLPT-DL CLPT-DF
95
Non-disconnect 15CLPT-PNM-B 15CLPT-GNM-B CLPT-NL CLPT-DF
3–10
Disconnect†† 15CLPT-PDM-B 15CLPT-GDM-B CLPT-DL —
25.5 kV Maximum (23 kV Nominal)
Non-disconnect 25CLPT-PNM-A 25CLPT-NL —
0.5–1 150 —
Disconnect ††
25CLPT-PDM-A 25CLPT-DL CLPT-DF
38 kV Maximum (34.5 kV Nominal)
Disconnect†† Not applicable CLPT-NL CLPT-DF
0.5 N/A Not applicable
Non-disconnect 38CLPT-PNM-A CLPT-DL —
* See page 7-35 for dimensions and diagrams of typical mountings.
** End fittings supplied only when required.
† Refers to 5CLPT, 5NCLPT, 8CLPT and 8NCLPT-A or -B fuses only.
†† Disconnect mountings provide a means for fuse extraction only. Do not use a disconnect mounting for load switching or fuse removal while energized.

Data sheet no. 6002

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-29
7 — Medium voltage fuses
HVA, HVB, HVJ, HVL, HVR, HVT, HVU, HVW and
HVX fast-acting PT fuses
Medium voltage, non-time delay, fast-acting fuses.

Ratings*

•• Volts 1-10 kV
•• Amps 1/16-10 A
* See catalog number table for possible volt/amp combinations.

Features

•• Physical size varies with electrical rating of fuse to prevent

overfusing
•• Space-saving size

Typical applications

•• Medium voltage instrument and circuit protection

Test specifications

Catalog symbol Percent load Opening time

110 4 hours (min)
HVA, HVB, HVJ, HVL
135 1 hour (max)
100 4 hours (min)
HVR, HVT, HVU, HVW, HVX
150 1 hour (max)

Recommended fuseclips and blocks

Fuse catalog symbol Block catalog no. Fuseclip catalog no.

HVA, HVR 4528*
5960
HVB, HVT 4529*
HVJ, HVU
— 4180
HVL, HVX
* Use #8 screws.

Dimensions — in (mm)
Catalog symbol kV Amps Max. IR (amps) Diameter Length
HVA 1 1/16, 1/10, 1/8, 2/10, 1/4, 3/8, 1/2, 3/4, 1, 1-1/2, 2, 3, 4, 6, 10 20 DC / 30 AC 3 (76)
0.4 (10)
HVB 2.5 1/2, 3/4, 1, 1-1/2, 2, 3 8 DC / 12 AC 4.5 (114)
HVJ 5 1/16, 1/8, 1/4, 1/2, 3/4, 1, 1-1/2, 2, 4, 6* 4 DC / 6 AC 5 (126.9)
0.8 (21)
HVL 10 1/16, 1/8, 1/4, 1/2, 1, 1-1/2, 2, 3* 2 DC / 3 AC 10 (254)
HVR 1 1/2, 1, 2, 3, 4, 5 500 AC 3 (76)
HVW 1.2 1, 2, 3, 4, 5, 8 4 DC / 167 AC 0.4 (10) 2.3 (57)
HVT 2.5 1/2, 1, 2, 3, 5 500 AC 4.5 (114)
HVU 5 1/2, 1, 2, 3, 4, 5 500 AC 5 (127)
0.8 (20)
HVX 10 1/2, 1, 3, 5 1200 AC 10 (254)
* AC only.

Catalog number build-a-code

Fuse catalog symbol Amps

_ _ _ _ _­ - ___
E.g., HVB-3/4 (2.5 kV 3/4 amp fuse)

Data sheet no. 6003

7-30 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
British standard dimensioned IEC fuses for motor
circuit protection
The Bussmann series IEC motor fuses are designed to meet the
specific requirements necessary for motor protection. During the
starting cycle of direct on-line motors, the fuse elements will reach
a considerably higher temperature than during normal operation;
(this is due to the high amount of current the motor will draw as it
starts, typically, six times its normal load current value). This results
in expansion and contraction of the fuse elements and could cause
premature operation of the fuse.
Bussmann series motor fuses encompass an advanced design
to minimize this effect. This, therefore, negates the need to over
specify the fuse rating due to high values of motor starting current.
These motor fuses operate extremely quickly under heavy fault
currents, resulting from the time / current characteristic. Low
power dissipation ensures low temperature rise, important in multi-
tier starters for example. Switching (arc), voltages are lower than
permitted values, therefore, 5.5 kV fuses are also suitable for 4.8 kV
and 2.4 kV circuits.

Catalog IR Dimensions — in (mm)

symbol kV (kA) Amps/rating Length Diameter Dimension standard
3.6WJON6 5, 6.3, 10, 16, 20, 25, 31.5, 40, 50 1.4 (36) BS 2692 (TA1) Interchangeable with GEC Type K2 PA
3.6WDOH6 50, 63, 80, 100, 125 7.6 (192) 2 (51)
BS 2692 (TA1) or DIN 43625
3.6WFOH6 160, 200 3 (76)
3.6WDLSJ 50, 63, 80, 100, 125 2 (51)
3.6 50 11.5 (292) DIN 43625
3.6WFLSJ 160, 200 3 (76)
3.6WDFHO 50, 63, 80, 100, 125 2 (51)
3.6WFFHO 160, 200 10 (254) BS 2692 (TA2)
3.6WKFHO 250, 315, 355, 400
5.5VFNHA 2R, 3R, 4R, 6R
5.5 60 ANSI R-Rated
5.5VKNHA 9R, 12R, 18R, 24R
15.9 (403) 3 (76)
7.2WFNHO 25, 31.5, 40, 50, 63, 80, 100, 125, 160
40 BS 2692 (TA4)
7.2WKNHO 200, 224, 250, 315
7.2
7.2WFMSJ 25, 31.5, 40, 50, 63, 80, 125, 160
63 17.4 (442) DIN 43625
7.2WKMSJ 200, 224, 250, 315, 355

Catalog number build-a-code

Fuse catalog symbol Amps

_ _ _ _ _­ - ___
E.g., 3.6WKFHO-315 (315 amp 3.6 kV fuse)

Medium voltage
fuses

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-31
7 — Medium voltage fuses
DIN dimensioned IEC fuses for transformer
protection
DIN dimension fuses to Specification DIN 43625 covering current-
limiting fuses with performance in compliance with IEC 60282-1.
These are in accordance with the R10 and, in some cases, the R20 Typical applications
series of preferred numbers.
•• Medium voltage IEC designed equipment
Ratings*
Recommended fuseclips
•• Volts 3.6-36 kV
•• Amps 6.3-100 A •• Catalog numbers 270303, A3354745, see page 7-36.
•• Interrupting ratings 20-50 kA
* See catalog number table for possible volt/amp combinations. Dimensions — in (mm)
Striker -in
Agency information operated position
0.59

Diameter
(15)
•• Compliant with DIN dimensional standard DIN 43625, VDE 0670 1.77
(45)
part 4, VDE 0670 part 40Z and with IEC 60282-1 (2005)

Features
Length 1.34 1.02
(34) (26)
For diameter and length values, see catalog number table.
•• DIN dimensioned for retrofitting in existing hardware
•• Open fuse indicator for ease in troubleshooting
•• Designed for use in IEC equipment

Catalog Dimensions — in (mm)

kV symbol Amps Diameter Length IR RMS Sym. (kA)
3.6ADOSJ 6.3, 10, 16, 20, 25, 31.5, 40 40
2.0 (51)
3.6WDOSJ 50, 63, 80, 100, 125 7.6 (192)
3.6 3.6WFOSJ 160, 200 3.0 (76)
50
3.6ADLSJ 25, 40 2.0 (51)
3.6WKLSJ 250, 315, 400 3.0 (76)
11.5 (292)
7.2TDLSJ 6.3, 10, 16, 20, 25, 31.5, 40, 50, 63 2.0 (51)
7.2 40
7.2TFLSJ 80, 100, 125, 160 3.0 (76)
12TDLEJ 6.3, 10, 16, 20, 25, 31.5, 40, 50, 63 2.0 (51)
12THLEJ 80, 100 2.5 (64)
12 63
12TKLEJ 125 3.0 (76)
11.5 (292)
12TXLEJ* 160, 200 3.5 (88)
17.5TDLSJ* 6.3, 10, 16, 20, 25, 31.5, 40 2.0 (51)
35.5
17.5TFLSJ* 50 3.0 (76)
17.5 17.5TDMEJ 6.3, 10, 16, 20, 25, 31.5, 40, 50, 63 2.0 (51)
17.5THMEJ 80, 100 2.5 (64) 50
17.5TKMEJ 125 3.0 (76)
24TDMEJ 6.3, 10, 16, 20, 25, 31.5, 40, 50 2.0 (51) 17.4 (442)
24THMEJ 63 2.5 (64) 50
24
24TFMEJ 80, 100*1 3.0 (76)
24TXMEJ* 1252, 160 3.5 (88) 31.5
36TDQSJ 3.153, 6.3, 10, 16, 20, 25 2.0 (51)
35.5
36 36TFQSJ 31.5, 40, 50 3.0 (76) 21.2 (537)
36TXQEJ* 63 3.5 (88) 20
* Not compliant with VDE 0670, part 402.
1 IR RMS Sym. is 63 kA
2 IR RMS Sym. is 40 kA
3 IR RMS Sym. is 20 kA

Catalog number build-a-code

Fuse catalog symbol Amps

_ _ _ _ _­ - ___
E.g., 17.5THMEJ-80 (17.5 kV 80 amp fuse)

7-32 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
Expulsion fuse links for use in high voltage Typical applications
distribution cut-outs •• Primary side transformer protection
Expulsion fuse links available in •• Feeder protection
a wide range of options from •• Capacitor bank protection
15 to 72 kV in ANSI Type T and
K characteristics. Expulsion Fuse label color coding
fuse link current ratings should
be selected on the basis of Type Color Type Color
maximum expected transient
no-damage currents rather than XA Pink T Green
on full load current. In addition, K Yellow S —
the selection of higher current
ratings will reduce the possibility Dimensions — mm (in)
of supply interruption due to
transient surges such as those A
125 (4.92)
due to lightning strikes.
Double tail
Links should be handled with a reasonable degree of care when Ø10 (0.39)
installing. Excessively rough handling may damage the element.
Universal
It is normal, under certain fault conditions, for arc extinguishing
material and/or metal particles to be expelled from the fuse Button head
assembly. It is therefore recommended that reasonable precautions
be taken to prevent the installation being approached by Ø7.5 (0.29)
unauthorized persons. Ø19 (0.75) Removeable button head

When ordering, select from the table below the characteristics in Up to 50 A A

each column you need your fuse link to have. A
125 (4.92)
Example: 15TB30 is a 15 kV, ANSI C 37-42 compliant fuse with a
Double tail
fixed button head terminal that is rated for 30 amps.
11 (0.43)
The fuse link assembly for a given range is standard to all rated Universal
voltages. The exception is the tail length that’s varied to suit the Adjustable button for 65 to 100 a assembly only
Ø19 (0.75)
expulsion carrier dimensions of different ratings.
Button head

Ratings* 10.5 (0.41)

Ø19 (0.75) Removeable button head
•• Volts 15-72 kV
60-100 A A
•• Amps 1-100 A
•• Interrupting rating 8 kA approximate Link kV A Link kV A
* See catalog number configuring table for possible volt/amp combinations. 15 533 (21) 46 787 (31)

Agency information 25 660 (26) 72 1016 (40

Notes: Type BR is similar to button head shown, except that the
•• Type T, complies with ANSI C37-42 button head is attached via a 1/4" UNF thread. Tails can be cut to
•• Type K, complies with ANSI C37-42 desired length.

Medium voltage
Features

fuses
•• Wide range of options available from 15 kV to 72 kV in ANSI T and
K characteristics.
•• Extra rapid option also available.

Catalog number configuration table

Available voltage Available amps
ratings (kV) 1st letter = current characteristics type 2nd letter = termination type ratings
T = complies with ANSI C 37-42 requirements for B = a fixed NEMA button head link
slow acting T characteristics
K = complies with ANSI C 37-42 requirements for U = a universal link, with double tail and slip off
fast acting K characteristics NEMA button head
XA = this type of expulsion fuse link has an extra 1, 2, 3, 4, 5, 6,
rapid characteristic. It is suitable for applications 7.5, 8, 10, 12, 15,
15, 25, 46, 72 D = double tailed link without NEMA button head 20, 25, 30, 40,
where a high degree of system protection is
required at the expense of discrimination. 50, 60, 65, 75,
80, 100
S = Solid links rated at 100 amps are also available
in both button head and universal versions for BR = as pattern B but the button head is attached via
fitting into expulsion fuse carriers where required. a 1/4" UNF thread to allow use of an extension rod
These can be ordered in a similar way using the
abbreviation S, e.g. 15SB, etc.

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-33
7 — Medium voltage fuses
FL — Type H, and EEI-NEMA Type K and T fuses Type H (high-surge), K and T universal tin element cutout
fuses rated to 27 kV
Medium voltage fuses: Type H (high surge), EEI-NEMA Type K (fast-
acting), EEI-NEMA Type T (time-delay). Catalog no.

High-surge, Type H fuses are EEI-NEMA

manufactured in ratings of 1, Type H high surge Type K fast-acting Type T time-delay Amps
2, 3, 5, and 8 amps and were
Non-removable button-head for standard open or enclosed cutouts
developed for primary fusing of
small-sized transformers. Type FL11H1 FL11K1 FL11T1 1
H links are manufactured in the FL11H2 FL11K2 FL11T2 2
universal button head design.
FL11H3 FL11K3 FL11T3 3
Type N fuses conform to previous
NEMA standards and are FL11H5 FL11K5 FL11T5 5
superseded by Type K and T links. — FL11K6 FL11T6 6
Type N fuses are manufactured
in the universal button design FL11H8 FL11K8 FL11T8 8
in ratings of 5 through 200 — FL11K10 FL11T10 10
amps for use in standard NEMA
dimensioned cutouts rated — FL11K12 FL11T12 12
through 27 kV. — FL11K15 FL11T15 15
— FL11K20 FL11T20 20
Ratings*
— FL11K25 FL11T25 25
•• Volts rated to 27 kV — FL11K30 FL11T30 30
•• Amps 1-200 A — FL11K40 FL11T40 40
* See catalog number table for type and amp combinations. — FL11K50 FL11T50 50
Features — FL11K65 FL11T65 65
— FL11K80 FL11T80 80
•• Wide range of EEI-NEMA type fuse links for use in open fuse
cutouts — FL11K100 FL11T100 100
— FL11K140 FL11T140 140
•• Voltage rating up to 27 kV for flexible application
— FL11K200 FL11T200 200
•• Can be coordinated with other overcurrent protective devices for
sectionalizing to isolate feeder branches Removable button-head for cutouts requiring removable-button links*
— FL3K1 FL3T1 1
Typical applications
— FL3K2 FL3T2 2
•• Medium voltage fused cutouts — FL3K3 FL3T3 3
— FL3K5 FL3T5 5
— FL3K6 FL3T6 6
— FL3K8 FL3T8 8
— FL3K10 FL3T10 10
— FL3K12 FL3T12 12
— FL3K15 FL3T15 15
— FL3K20 FL3T20 20
Type K universal silver-element cutout fuses rated to 27 kV
— FL3K25 FL3T25 25
Catalog no.
— FL3K30 FL3T30 30
Fast-acting EEI-NEMA Type K Amps
— FL3K40 FL3T40 40
Non-removable button-head for standard open or enclosed cutouts
— FL3K50 FL3T50 50
FL12K8 8
— FL3K65 FL3T65 65
FL12K10 10
— FL3K80 FL3T80 80
FL12K12 12
— FL3K100 FL3T100 100
FL12K15 15
— FL3K140 FL3T140 140
FL12K25 25
— FL3K200 FL3T200 200
FL12K50 50 * Adapter-type removable-button links with ferrule adapter to convert to double-
leader links are available in K and T types. Order by description.

7-34 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries
 Medium voltage fuses — 7
PT fuse mountings — in (mm)
Catalog no. Hole ctrs. A Hole ctrs. B Overall length C Hole Inset D Hole ctrs. E Contact hgt. F Overall hgt. G BIL (kV)
5.5 kV Disconnect†
5CLPT-GDM-A
9.37 (238) 6 (152.4) 18.63 (473.2) 0.75 (19) 1.75 (44.4) 4.5 (114.3) 9.56 (242.8) 60
5CLPT-PDM-A
5.5 kV Non-disconnect
5CLPT-GNM-A
9.37 (238) 6 (152.4) 18.63 (473.2) 0.75 (19) 1.75 (44.4) 4.5 (114.3) 6.94 (176.2) 60
5CLPT-PNM-A
8.3 kV Disconnect†
8CLPT-GDM-A
8CLPT-GDM-B 9.37 (238) 18.63 (473.2)
6 (152.4) 0.75 (19) 1.75 (44.4) 7 (177.8) 12.06 (306.3) 75
8CLPT-PDM-A
8CLPT-PDM-B 12.74 (323.6) 22 (558.8)
8.3 kV Non-disconnect
8CLPT-GNM-A
9.37 (238) 18.63 (473.2)
8CLPT-PNM-A
6 (152.4) 0.75 (19) 1.75 (44.4) 7 (177.8) 9.44 (239.8) 75
8CLPT-GNM-B
12.75 (323.8) 22 (558.8)
8CLPT-PNM-B
15.5 kV Disconnect†
15CLPT-GDM-A
12.74 (323.6) 22 (558.8)
15CLPT-PDM-A
6 (152.4) 0.75 (19) 1.75 (44.4) 7 (177.8) 12.06 (306.3) 95
15CLPT-GDM-B
17.46 (443.5) 26.63 (676.4)
15CLPT-PDM-B
15.5 kV Non-disconnect
15CLPT-GNM-A
12.74 (323.6) 22 (558.8)
15CLPT-PNM-A
6 (152.4) 0.75 (19) 1.75 (44.4) 7 (177.8) 9.44 (239.8) 95
15CLPT-GNM-B
17.46 (443.5) 26.63 (676.4)
15CLPT-PNM-B
25.5 kV Disconnect†
25CLPT-PDM-A 19.12 (485.6) 7 (177.8) 26.63 (676.4) 0.75 (19) 1.75 (44.4) 12 (304.8) 17.06 (433.3) 150
25.5 kV Non-disconnect
25CLPT-PNM-A 26.63 (676.4) 7 (177.8) 26.63 (676.4) 0.75 (19) 1.75 (44.4) 12 (304.8) 14.75 (374.6) 150
† Disconnect mountings provide a means for fuse extraction only. Do not use a disconnect mounting for load switching or fuse removal while energized.

Disconnect mountings†† Non-disconnect mountings

G G
D F D F

E E

Medium voltage
fuses
A C A C

E E

D B
D B

BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries 7-35
7 — Medium voltage fuses
Recommended fuseclips

Clip Dimensions — in (mm)

Description Fuse dia. — in (mm) Fig. A B ØC D E F G Catalog no.
DIN clip and stirrup 1 — — — — — — — 270303
1.8 (45)
Enclosed fuseclip 2 3.5 (89) 2.5 (63) 1.8 (45) 4.4 (112) A3354745*
Enclosed fuseclip 2 (51) 2 3.75 (95) 1.98 (50) 2.01 (51) 1.19 (30) 4.54 (115) 1.5 (38) 0.4 (10) A3354710*
Enclosed fuseclip 2 4.14 (105) 2.45 (62) 3.01 (76) 5.64 (143) A3354730*
Open fuseclip 3 (76) 3 1A0065
See dimensions drawing
Spring loaded open fuseclip 4 9078A67G04
* For single barrel applications only. Not sold in pairs.

Figure 1 Figure 2

ØC
A

D
B

26.5
6.5

Figure 3 Figure 4

7-36 BUSSMANN SERIES FULL LINE CATALOG 1007 — OCTOBER 2018 Eaton.com/bussmannseries