Manualslib.

com - Simplified Manuals

Manuals / Brands / Honda Manuals / Motorcycle / CBR150R 2018 / Owner's manual / PDF

HONDA CBR150R 2018 OWNER'S MANUAL

Quick Links
Maintenance
Engine Oil
Specifications
Table of Contents
Motorcycle Safety
Safety Guidelines
Safety Precautions
Riding Precautions
Accessories & Modifications
Loading
Operation Guide
Importance of Maintenance
Maintenance Schedule
Maintenance Fundamentals
Tool
Removing & Installing Body Components
Battery
Clip
Front Seat
Harness Band Clip
Right Middle Cowl
Rear Seat
Spark Plug
Engine Oil
Coolant
Brakes
Side Stand
Drive Chain
Clutch
Throttle
Crankcase Breather
Other Adjustments
Adjusting the Headlight Aim
Adjusting the Front Suspension
Adjusting the Rear Suspension
Engine Will Not Start
Overheating (High coolant temperature indicator is on)
Warning Indicators On or Flashing
PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL)
ABS (Anti-lock Brake System) Indicator
Other Warning Indications
Fuel Gauge Failure Indication
Tyre Puncture
Electrical Trouble
Battery Goes Dead
Burned-out Light Bulb
Blown Fuse
Unstable Engine Operation Occurs Intermittently
Keys
Instruments, Controls, & Other Features
Caring for Your Motorcycle
Storing Your Motorcycle
Transporting Your Motorcycle
You & the Environment
Serial Numbers
Fuels Containing Alcohol
Catalytic Converter
Specifications
Index
This manual should be considered a permanent part of the
motorcycle and should remain with the motorcycle when it is resold.

This publication includes the latest production information available

before printing. Honda Motor Co., Ltd. reserves the right to make
changes at any time without notice and without incurring any
obligation.

No part of this publication may be reproduced without written

permission.

The vehicle pictured in this owner’s manual may not match your
actual vehicle.

© 2018 Honda Motor Co., Ltd.

 Welcome
Congratulations on your purchase of a new ● The illustrations here in are based on the
Honda motorcycle. Your selection of a CBR150RA III PH type.
Honda makes you part of a worldwide family
of satisfied customers who appreciate Country Codes
Honda's reputation for building quality into Code Country
every product. CBR150R
PH, V PH Philippines
To ensure your safety and riding pleasure: IN, III IN, V IN Indonesia
● Read this owner's manual carefully. CBR150RA
● Follow all recommendations and III PH Philippines
procedures contained in this manual. IN, III IN, V IN Indonesia
● Pay close attention to safety messages
*The specifications may vary with each locale.
contained in this manual and on the
motorcycle.
● The following codes in this manual
indicate each country.
 A Few Words About Safety
Your safety, and the safety of others, is very
3DANGER
important. Operating this motorcycle safely is
an important responsibility. You WILL be KILLED or SERIOUSLY
To help you make informed decisions about HURT if you don’t follow instructions.
safety, we have provided operating
procedures and other information on safety 3WARNING
labels and in this manual. This information You CAN be KILLED or SERIOUSLY
alerts you to potential hazards that could HURT if you don’t follow instructions.
hurt you or others.
Of course, it is not practical or possible to 3CAUTION
warn you about all hazards associated with You CAN be HURT if you don’t follow
operating or maintaining a motorcycle. You instructions.
must use your own good judgement.

You will find important safety information in a Other important information is

variety of forms, including: provided under the following titles:
NOTICE Information to help you avoid
● Safety labels on the motorcycle
● Safety Messages preceded by a safety alert damage to your motorcycle,
symbol and one of three signal words: other property, or the
DANGER, WARNING, or CAUTION. environment.
These signal words mean:
Contents

Motorcycle Safety P. 2

Operation Guide P. 12

Maintenance P. 33

Troubleshooting P. 82

Information P. 100

Specifications P. 112

Index P. 115
Motorcycle Safety

This section contains important information for safe riding of your motorcycle.
Please read this section carefully.

Safety Guidelines ................................................. P. 3

Safety Precautions............................................... P. 6
Riding Precautions .............................................. P. 7
Accessories & Modifications........................... P. 10
Loading ................................................................ P. 11
 Safety Guidelines

Safety Guidelines Before Riding

Make sure that you are physically fit, mentally

Motorcycle Safety
Follow these guidelines to enhance your safety:
focused and free of alcohol and drugs. Check
● Perform all routine and regular inspections
that you and your passenger are both wearing
specified in this manual.
an approved motorcycle helmet and protective
● Stop the engine and keep sparks and flame
apparel. Instruct your passenger on holding
away before filling the fuel tank.
onto the seat strap or your waist, leaning with
● Do not run the engine in enclosed or partly
you in turns, and keeping their feet on the
enclosed areas. Carbon monoxide in
footpegs, even when the motorcycle is stopped.
exhaust gases is toxic and can kill you.

Take Time to Learn & Practice

Always Wear a Helmet
Even if you have ridden other motorcycles,
It's a proven fact: helmets and protective
practice riding in a safe area to become familiar
apparel significantly reduce the number and
with how this motorcycle works and handles,
severity of head and other injuries. So always
and to become accustomed to the motorcycle's
wear an approved motorcycle helmet and
size and weight.
protective apparel. 2 P. 6

Continued 3
 Safety Guidelines

Ride Defensively Don't Drink and Ride

Always pay attention to other vehicles around Alcohol and riding don't mix. Even one alcoholic
Motorcycle Safety

you, and do not assume that other drivers see drink can reduce your ability to respond to
you. Be prepared to stop quickly or perform an changing conditions, and your reaction time
evasive maneuver. gets worse with every additional drink. Don't
drink and ride, and don't let your friends drink
and ride either.
Make Yourself Easy to See
Make yourself more visible, especially at night,
by wearing bright reflective clothing, positioning Keep Your Honda in Safe Condition
yourself so other drivers can see you, signaling It's important to keep your motorcycle properly
before turning or changing lanes, and using maintained and in safe riding condition.
your horn when necessary. Inspect your motorcycle before every ride and
perform all recommended maintenance. Never
exceed load limits (2 P. 11), and do not modify
Ride within Your Limits your motorcycle or install accessories that
Never ride beyond your personal abilities or would make your motorcycle unsafe (2 P. 10).
faster than conditions warrant. Fatigue and
inattention can impair your ability to use good
judgement and ride safely.

4
 Safety Guidelines

If You are Involved in a Crash Carbon Monoxide Hazard

Personal safety is your first priority. If you or Exhaust contains poisonous carbon monoxide, a

Motorcycle Safety
anyone else has been injured, take time to colourless, odorless gas. Breathing carbon
monoxide can cause loss of consciousness and
assess the severity of the injuries and whether it may lead to death.
is safe to continue riding. Call for emergency
assistance if needed. Also follow applicable laws If you run the engine in confined or even partly
and regulations if another person or vehicle is enclosed area, the air you breathe could contain
involved in the crash. a dangerous amount of carbon monoxide.
Never run your motorcycle inside a garage or
other enclosure.
If you decide to continue riding, first turn the
ignition switch to the OFF position, and evaluate 3WARNING
the condition of your motorcycle. Inspect for Running the engine of your motorcycle
fluid leaks, check the tightness of critical nuts while in an enclosed or even partially
and bolts, and check the handlebars, control enclosed area can cause a rapid build-
levers, brakes, and wheels. Ride slowly and up of toxic carbon monoxide gas.
cautiously.
Your motorcycle may have suffered damage Breathing this colourless, odorless gas
can quickly cause unconsciousness and
that is not immediately apparent. Have your
lead to death.
motorcycle thoroughly checked at a qualified
service facility as soon as possible.
Only run your motorcycle's engine
when it is located in a well ventilated
area outdoors.

5
 Safety Precautions

Safety Precautions ● Face shield with unobstructed field of vision

or other approved eye protection
Motorcycle Safety

● Ride cautiously and keep your hands on the

handlebars and feet on the footpegs. 3WARNING
● Keep passenger's hands onto the seat strap Not wearing a helmet increases the
or your waist, passenger's feet on the chance of serious injury or death in a
footpegs while riding. crash.
● Always consider the safety of your
passenger, as well as other drivers and
Make sure that you and any passenger
riders.
always wear an approved helmet and
Protective Apparel protective apparel.
Make sure that you and any passenger are
wearing an approved motorcycle helmet, eye # Gloves
protection, and high-visibility protective Full-finger leather gloves with high abrasion
clothing. Ride defensively in response to resistance
weather and road conditions. # Boots or Riding Shoes
Sturdy boots with non-slip soles and ankle
# Helmet protection
Safety-standard certified, high-visibility, correct
size for your head # Jacket and Trousers
● Must fit comfortably but securely, with the Protective, highly visible, long-sleeved jacket
chin strap fastened. and durable trousers for riding (or a protective
suit)
6
 Riding Precautions

Riding Precautions Brakes

Observe the following guidelines:

Motorcycle Safety
Running-in Period ● Avoid excessively hard braking and
During the first 500 km (300 miles) of running, downshifting.
follow these guidelines to ensure your u Sudden braking can reduce the
motorcycle's future reliability and performance. motorcycle's stability.
● Avoid full-throttle starts and rapid u Where possible, reduce speed before
acceleration. turning; otherwise you risk sliding out.
● Avoid hard braking and rapid down-shifts. ● Exercise caution on low traction surfaces.
● Ride conservatively. u The tyres slip more easily on such
surfaces and braking distances are
longer.
● Avoid continuous braking.
u Repeated braking, such as when
descending long, steep slopes can
seriously overheat the brakes, reducing
their effectiveness. Use engine braking
with intermittent use of the brakes to
reduce speed.
● For full braking effectiveness, operate both
the front and rear brakes together.

Continued 7
 Riding Precautions

# Anti-lock Brake System (ABS) # Wet or Rainy Conditions

CBR150RA Road surfaces are slippery when wet, and wet
Motorcycle Safety

This model is equipped with an Anti-lock Brake brakes further reduce braking efficiency.
System (ABS) designed to help prevent the Exercise extra caution when braking in wet
brakes from locking up during hard braking. conditions.
● ABS does not reduce braking distance. In If the brakes get wet, apply the brakes while
certain circumstances, ABS may result in a riding at low speed to help them dry.
longer stopping distance.
● ABS does not function at speeds below 10
km/h (6 mph).
● The brake lever and pedal may recoil slightly
when applying the brakes. This is normal.
● Always use the recommended front/rear
tyres and sprockets to ensure correct ABS
operation.

# Engine Braking
Engine braking helps slow your motorcycle
down when you release the throttle. For further
slowing action, downshift to a lower gear. Use
engine braking with intermittent use of the
brakes to reduce speed when descending long,
steep slopes.
8
 Riding Precautions

Parking 3. Slowly lean the motorcycle to the left until its

weight rests on the side stand.
● Park on a firm, level surface.

Motorcycle Safety
4. Turn the handlebars fully to the left.
● If you must park on a slight incline or loose
u Turning the handlebars to the right
surface, park so that the motorcycle cannot
reduces stability and may cause the
move or fall over.
motorcycle to fall.
● Make sure that high-temperature parts
5. Turn the ignition switch to the LOCK
cannot come into contact with flammable
position (2 P. 24), remove the key and close
materials.
the shutter (2 P. 25).
● Do not touch the engine, muffler, brakes
and other high-temperature parts until they
cool down. Refuelling and Fuel Guidelines
● To reduce the likelihood of theft, always lock
Follow these guidelines to protect the engine,
the handlebars and remove the key and
fuel system and catalytic converter:
close the shutter when leaving the
● Use only unleaded petrol.
motorcycle unattended.
● Use recommended octane number. Using
Use of an anti-theft device is also
lower octane petrol will result in decreased
recommended.
engine performance.
● Do not use fuels containing a high
# Parking with the Side Stand concentration of alcohol. 2 P. 110
1. Stop the engine. ● Do not use stale or contaminated petrol or
2. Push the side stand down. an oil/petrol mixture.
● Avoid getting dirt or water in the fuel tank.

9
 Accessories & Modifications

Accessories & 3WARNING

Modifications
Motorcycle Safety

Improper accessories or modifications

We strongly advise that you do not add any can cause a crash in which you can be
accessories that were not specifically designed seriously hurt or killed.
for your motorcycle by Honda or make
modifications to your motorcycle from its Follow all instructions in this owner's
original design. Doing so can make it unsafe. manual regarding accessories and
Modifying your motorcycle may also void your modifications.
warranty and make your motorcycle illegal to
operate on public roads. Before deciding to Do not pull a trailer with, or attach a sidecar to,
install accessories on your motorcycle be certain your motorcycle. Your motorcycle was not
the modification is safe and legal. designed for these attachments, and their use
can seriously impair your motorcycle's handling.

10
 Loading

Loading 3WARNING

Motorcycle Safety
● Carrying extra weight affects your Overloading or improper loading can
motorcycle's handling, braking and stability.
cause a crash and you can be seriously
Always ride at a safe speed for the load you
hurt or killed.
are carrying.
● Avoid carrying an excessive load and keep
within specified load limits. Follow all load limits and other loading
Maximum weight capacity 2 P. 112 guidelines in this manual.
● Tie all luggage securely, evenly balanced
and close to the centre of the motorcycle.
● Do not place objects near the lights or the
muffler.

11
 Parts Location
Rear brake fluid reservoir (P.66
Fuse box (P.97
Operation Guide

Battery (P.51

Front brake fluid reservoir

(P.66

Throttle grip (P.77

Spark plug (P.59

Right middle cowl (P.56

Engine oil fill cap/dipstick

(P.61

Coolant reserve tank (P.64

12
 Clutch lever (P.74
Front suspension spring preload
adjuster (P.80

Operation Guide
Fuel fill cap (P.31
Front seat (P.53
Rear seat (P.58
Document bag (P.32
Tool kit (P.32
Shift lever (P.28
Rear suspension spring preload
adjuster (P.81
Drive chain (P.70
Engine oil drain bolt (P.63

Side stand (P.69

Crankcase breather (P.78

13
 Instruments
Tachometer
NOTICE
Do not operate the engine in the tachometer red zone.
Operation Guide

Excessive engine speed can adversely affect engine life.

Tachometer red zone

(excessive engine rpm range)

SEL button SET button

Display Check
When the ignition switch is turned on, all the mode and digital segments will
show. If any part of these displays does not come on when it should, have your
dealer check for problems.

14
Odometer [TOTAL] & Tripmeter [TRIP A/B] & Current fuel
mileage & Average fuel mileage [AVG A/B] (P.16

Operation Guide
Clock (12-hour display)
To set the clock: (P.19

Fuel gauge
Remaining fuel when only 1st (E)
segment starts flashing: approximately
1.8 L (0.48 US gal, 0.40 Imp gal)
If the fuel gauge indicator flashes in a repeat pattern
or turns off: (P.86

Speedometer

Gear position indicator

The gear position is shown in the gear position indicator.
u “-” appears when the transmission is not shifted properly.

Continued 15
 Instruments (Continued)
Odometer [TOTAL] & Tripmeter [TRIP A/B] & Current fuel mileage & Average fuel
mileage [AVG A/B]
The SEL button switches between the odometer, tripmeter A, tripmeter B, current fuel mileage,
Operation Guide

average fuel mileage A and average fuel mileage B.

Odometer Tripmeter A Tripmeter B

Average fuel Average fuel Current fuel

mileage B mileage A mileage

16
# Odometer [TOTAL] # Average fuel mileage [AVG A/B]
Total distance ridden. When “------” is The average fuel mileage A will be based on
displayed, go to your dealer for service. tripmeter A. The average fuel mileage A

Operation Guide
since tripmeter A was reset.
# Tripmeter [TRIP A/B] The average fuel mileage B will be based on
tripmeter B. The average fuel mileage B since
Distance ridden since tripmeter was reset.
When “-----.-” is displayed, go to your dealer tripmeter B was reset.
for service. Display range: 0.0 to 99.9 km/L
To reset the tripmeter: (P.18 • Initial display: “--.-” is displayed.
• More than 99.9 km/L: “99.9” is displayed.
# Current fuel mileage • When the tripmeter A or B is reset: “--.-”
Displays the current or instant fuel mileage. is displayed.
Display range: 0.0 to 99.9 km/L
• Initial display: “--.-” is displayed. When “--.-” is displayed except for the
• When your speed is less than 6 km/h (4 above-mentioned cases, go to your dealer
mph): “--.-” is displayed. for service.
• More than 99.9 km/L: “99.9” is displayed. To reset the average fuel mileage:
(P.18
When “--.-” is displayed except for the
above-mentioned cases, go to your dealer
for service.
Continued 17
 Instruments (Continued)
# To reset the tripmeter [TRIP A/B] and To reset the tripmeter B and average fuel
average fuel mileage [AVG A/B] mileage B together, press and hold the SET
To reset the tripmeter A and average fuel button while the tripmeter B or average fuel
Operation Guide

mileage A together, press and hold the SET mileage B is displayed.

button while the tripmeter A or average fuel
mileage A is displayed.
or

or Tripmeter B Average fuel

mileage B
Tripmeter A Average fuel
mileage A

18
To set the clock e Press the SEL button until the desired
a Turn the ignition switch on. minute is displayed.
b Press and hold the SEL and the SET buttons u Press and hold the SEL button to
until the hour digits start flashing. advance the minute fast.

Operation Guide
c Press the SEL button until the desired hour is f Press the SET button. The clock is set.
displayed. u The time can also be set by turning the
u Press and hold the SEL button to ignition switch off.
advance the hour fast. u The display will stop flashing
automatically and the adjustment will be
cancelled if the button is not pressed for
about 30 seconds.

d Press the SET button. The minute digits start

flashing.

19
 Indicators
If one of these indicators does not come on when it should, have your dealer check for
problems.
Operation Guide

PGM-FI (Programmed Fuel Injection) ABS (Anti-lock Brake System)

malfunction indicator lamp (MIL) indicator CBR150RA
Comes on briefly when the ignition switch is Comes on when the ignition switch is
turned to the ON position. turned to the ON position.
If it comes on while engine is running: Goes off when your speed reaches
(P.85 approximately 10 km/h (6 mph).
If it comes on while riding: (P.85

20
 Operation Guide
High coolant temperature indicator
Comes on briefly when the ignition
switch is turned to the ON position.
If it comes on while riding: (P.84
Neutral indicator
Comes on when the
transmission is in Neutral.
Right turn signal indicator
High beam indicator
Left turn signal indicator

21
 Switches
Start button
Headlight dimmer switch
Operation Guide

• : High beam
• : Low beam

Horn button

Turn signal switch

Passing light control switch u Pressing the switch turns
the turn signal off.
Flashes the high beam headlight.

22
Ignition switch ON
Switches the electrical system on/off, Turns electrical system
locks the steering. on for starting/riding.
u Key can be removed when in the OFF or

Operation Guide
LOCK position. OFF
Turns engine off.
LOCK
Locks steering.

Continued 23
 Switches (Continued)
Steering Lock # Locking
Lock the steering when parking to help a Turn the handlebars all the way to the left.
prevent theft. b Push the key down, and turn the ignition
Operation Guide

A U-shaped wheel lock or similar device is switch to the LOCK position.

also recommended. u Jiggle the handlebars if the lock is
difficult to engage.
Push c Remove the key.
b
Turn
# Unlocking
Insert the key, and turn the ignition switch to
the OFF position.
Ignition key
a

24
Shutter # Close
The ignition switch for this motorcycle is a Remove the ignition key from the ignition
equipped with a shutter. After parking the switch.

Operation Guide
motorcycle, close the shutter for theft b Align the projection of the shutter key with
prevention. the slot of the shutter, and turn the shutter
key counterclockwise.
u You can also close the shutter by moving
Close the knob downward without the shutter
key.
c Remove the key.
Close Open

Knob
# Open
Align the projection of the shutter key with
Shutter key the slot of the shutter, and turn the shutter
Ignition key key clockwise.

Slot Projection

25
 Starting the Engine
Start your engine using the following Consult your dealer for advice if you plan to
procedure, regardless of whether the engine ride your motorcycle at an altitude above
is cold or warm. 2,500 m (8,000 feet).
Operation Guide

b NOTICE
If the motorcycle is transported to a place 2,000
m (6,500 feet) higher or lower than the start
point, you may not be able to achieve sufficient
a engine performance at the new altitude. Consult
your dealer before transporting your motorcycle.

c a Turn the ignition switch to the ON position.

b Shift the transmission to Neutral ( N
indicator to come on).
NOTICE
c With the throttle closed, press the start
• If the engine does not start within 5 seconds,
button.
turn the ignition switch to the OFF position
and wait 10 seconds before trying to start
Release the start button as soon as the
the engine again to recover battery voltage. engine starts.
• Extended fast idling and revving the engine can
damage the engine, and the exhaust system

26
If you cannot start a warm engine: If the engine does not start:
Rotate the throttle 1/8 – 1/4 turn while a Open the throttle fully and press the start
starting the engine. button for 5 seconds.
b Repeat the normal starting procedure.

Operation Guide
1/8 c If the engine starts, open the throttle slightly
1/4
if idling is unstable.
d If the engine does not start, wait 10 seconds
before trying step a & b again.

# If Engine Will Not Start (P.83

27
 Shifting Gears
Your motorcycle transmission has 6 forward
gears in a one-down, five-up shift pattern.

6
45
Operation Guide

23

28
Emergency Stop Signal
CBR150RA The emergency stop signal stops operating
Emergency stop signal activates when you when:
brake hard while driving at 50 km/h (31 mph) ● You release the brake lever and pedal.

Operation Guide
or above to alert drivers behind you about ● The ABS is deactivated.
sudden braking by rapidly flashing both turn ● Your motorcycle’s decelerating speed
signal lights. This may help to alert drivers becomes moderate.
behind you to take appropriate means to
avoid a possible collision with your
motorcycle.

When the system activates:

Hard braking
Brakelight come on

Both turn signals flash

Both turn signal indicators blink

Continued 29
 Emergency Stop Signal (Continued)
u The emergency stop signal is not a system
that can prevent a possible rear-end
collision caused by your hard braking. It is
always recommended to avoid hard braking
Operation Guide

unless it is absolutely necessary.

u If the ABS stops working for a certain period
during braking, the emergency stop signal
may not activate at all.

30
Refuelling
Ignition key Opening the Fuel Fill Cap
Lock cover Fuel filler Open the lock cover, insert the ignition key,
opening and turn it clockwise to open the fuel fill cap.

Operation Guide
Closing the Fuel Fill Cap
a After refuelling, push the fuel fill cap closed
until it locks.
Fuel neck b Remove the ignition key and close the lock
plate cover.
Fuel fill cap u The ignition key cannot be removed if
the fuel fill cap is not locked.
Do not fill with fuel above the filler neck
plate. 3WARNING
Petrol is highly flammable and
Fuel type: Unleaded petrol only
explosive. You can be burned or
Fuel octane number: Your motorcycle is
seriously injured when handling fuel.
designed to use Research Octane Number
(RON) 88 or higher.
• Stop the engine, and keep heat,
Tank capacity: 12 L (3.2 US gal, 2.6 Imp gal)
sparks, and flame away.
• Handle fuel only outdoors.
# Refuelling and Fuel Guidelines (P.9 • Wipe up spills immediately.
31
 Storage Equipment
The helmet holder, helmet set wire (in the Document bag
tool kit), tool kit, and document bag are
located under the rear seat.
Operation Guide

Helmet set wire

Helmet holder Helmet D-ring

Tool kit Rubber strap
Helmet set wire
3WARNING
Riding with a helmet attached to the
holder can interfere with the rear wheel
or suspension and could cause a crash
in which you can be seriously hurt or
killed.

u Use the helmet holder only when parked. Use the helmet holder only while
parked. Do not ride with a helmet
# Removing the Rear Seat (P.58 secured by the holder.
32
 Maintenance

Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully

before attempting any maintenance. Refer to “Specifications” for service data.

Importance of Maintenance ........................... P. 34 Brakes................................................................... P. 66

Maintenance Schedule..................................... P. 35 Side Stand ........................................................... P. 69
Maintenance Fundamentals ........................... P. 38 Drive Chain.......................................................... P. 70
Tool ....................................................................... P. 50 Clutch ................................................................... P. 74
Removing & Installing Body Components.. P. 51 Throttle ................................................................ P. 77
Battery .................................................................... P. 51 Crankcase Breather ........................................... P. 78
Clip .......................................................................... P. 52 Other Adjustments............................................ P. 79
Front Seat .............................................................. P. 53 Adjusting the Headlight Aim ............................ P. 79
Harness Band Clip ............................................... P. 55 Adjusting the Front Suspension....................... P. 80
Right Middle Cowl............................................... P. 56 Adjusting the Rear Suspension ........................ P. 81
Rear Seat ............................................................... P. 58
Spark Plug ........................................................... P. 59
Engine Oil ............................................................ P. 61
Coolant................................................................. P. 64
 Importance of Maintenance

Importance of Maintenance Maintenance Safety

Keeping your motorcycle well-maintained is Always read the maintenance instructions
absolutely essential to your safety and to before you begin each task, and make sure that
protect your investment, obtain maximum you have the tools, parts, and skills required.
performance, avoid breakdowns, and reduce air We cannot warn you of every conceivable
Maintenance

pollution. Maintenance is the owner's hazard that can arise in performing

responsibility. Be sure to inspect your maintenance. Only you can decide whether or
motorcycle before each ride, and perform the not you should perform a given task.
periodic checks specified in the Maintenance
Schedule. 2 P. 35 Follow these guidelines when performing
maintenance.
3WARNING ● Stop the engine and remove the key.
Improperly maintaining your ● Place your motorcycle on a firm, level
motorcycle or failing to correct a surface using the side stand or a
problem before you ride can cause a maintenance stand to provide support.
crash in which you can be seriously hurt ● Allow the engine, muffler, brakes, and other

or killed. high-temperature parts to cool before

servicing as you can get burned.
● Run the engine only when instructed, and
Always follow the inspection and
do so in a well-ventilated area.
maintenance recommendations and
schedules in this owner's manual.

34
 Maintenance Schedule
The maintenance schedule specifies the All scheduled maintenance is considered a
maintenance requirements necessary to normal owner operating cost and will be
ensure safe, dependable performance, and charged to you by your dealer. Retain all
proper emission control. receipts. If you sell the motorcycle, these
receipts should be transferred with the
motorcycle to the new owner.

Maintenance
Maintenance work should be performed in
accordance with Honda's standards and
specifications by properly trained and equipped Honda recommends that your dealer should
technicians. Your dealer meets all of these road test your motorcycle after each periodic
requirements. Keep an accurate record of maintenance is carried out.
maintenance to help ensure that your
motorcycle is properly maintained.
Make sure that whomever performs the
maintenance completes this record.

Continued 35
 Maintenance Schedule

Frequency *1
Pre-ride Annual Regular Refer to
Items Check × 1,000 km 1 6 12 18 24 30 36 Check Replace page
2 P. 38
× 1,000 mi 0.6 4 8 12 16 20 24
Fuel Line –
Fuel Level 31
Throttle Operation 77
Maintenance

Air Cleaner *2 49
Crankcase Breather *3 78
Spark Plug 59
Valve Clearance –
Engine Oil 61
Engine Oil Strainer
Screen –

Engine Idle Speed –

Radiator Coolant *4 3 Years 64
Cooling System –

Maintenance Level Maintenance Legend

Intermediate. We recommend service by your dealer, unless Inspect (clean, adjust, lubricate, or replace, if necessary)
you have the necessary tools and are mechanically skilled. Clean
Procedures are provided in an official Honda Shop Manual. Lubricate
Technical. In the interest of safety, have your Replace
motorcycle serviced by your dealer.

36
 Maintenance Schedule

Frequency *1
Pre-ride Annual Regular Refer to
Items Check × 1,000 km 1 6 12 18 24 30 36 Check Replace page
2 P. 38
× 1,000 mi 0.6 4 8 12 16 20 24
Drive Chain Every 500 km (300 mi): 70
Brake Fluid *4 2 Years 66
Brake Pads Wear 67

Maintenance
Brake System 38
Brakelight Switch 68
Headlight Aim 79
Lights/Horn –
Clutch System 74
Side Stand 69
Suspension –
Nuts, Bolts, Fasteners –
Wheels/Tyres 46
Steering Head Bearings –

Notes:
*1 At higher odometer reading, repeat at the frequency interval established here.
*2 Service more frequently when riding in unusually wet or dusty areas.
*3 Service more frequently when riding in rain or at full throttle.
*4 Replacement requires mechanical skill.

37
 Maintenance Fundamentals

Pre-ride Inspection ● Drive chain - Check condition and slack,

adjust and lubricate if necessary. 2 P. 70
To ensure safety, it is your responsibility to
● Brakes - Check operation;
perform a pre-ride inspection and make sure
Front and Rear: check brake fluid level and
that any problem you find is corrected. A pre-
pads wear. 2 P. 66, 2 P. 67
ride inspection is a must, not only for safety, but
Lights and horn - Check that lights,
Maintenance

●
because having a breakdown, or even a flat
indicators and horn function properly.
tyre, can be a major inconvenience.
● Clutch - Check operation;
Adjust freeplay if necessary. 2 P. 74
Check the following items before you get on
● Wheels and tyres - Check condition, air
your motorcycle:
pressure and adjust if necessary. 2 P. 46
● Fuel level - Fill fuel tank when necessary.
2 P. 31
● Throttle - Check for smooth opening and
full closing in all steering positions. 2 P. 77
● Engine oil level - Add engine oil if necessary.
Check for leaks. 2 P. 61
● Coolant level - Add coolant if required.
Check for leaks. 2 P. 64

38
 Maintenance Fundamentals

Replacing Parts 3WARNING

Always use Honda Genuine Parts or their Installing non-Honda parts may make
equivalents to ensure reliability and safety. your motorcycle unsafe and cause a
crash in which you can be seriously hurt
or killed.

Maintenance
Always use Honda Genuine Parts or
equivalents that have been designed
and approved for your motorcycle.

39
 Maintenance Fundamentals

Battery This symbol on the battery means that this

product must not be treated as household waste.
Your motorcycle has a maintenance-free type
NOTICE
battery. You do not have to check the battery
electrolyte level or add distilled water. Clean the An improperly disposed of battery can be
harmful to the environment and human health.
battery terminals if they become dirty or
Maintenance

Always confirm local regulations for proper

corroded.
battery disposal instruction.
Do not remove the battery cap seals. There is
no need to remove the cap when charging.
NOTICE
Your battery is a maintenance-free type and can be
permanently damaged if the cap strip is removed.

40
 Maintenance Fundamentals

# What to do in an emergency 3WARNING

If any of the following occur, immediately see
your doctor. The battery gives off explosive
● Electrolyte splashes into your eyes: hydrogen gas during normal operation.
u Wash your eyes repeatedly with cool
water for at least 15 minutes. Using water A spark or flame can cause the battery

Maintenance
under pressure can damage your eyes. to explode with enough force to kill or
● Electrolyte splashes onto your skin: seriously hurt you.
u Remove affected clothing and wash your
skin thoroughly using water.
Wear protective clothing and a face
● Electrolyte splashes into your mouth:
shield, or have a skilled mechanic do
u Rinse mouth thoroughly with water, and
do not swallow. the battery servicing.

# Cleaning the Battery Terminals

1. Remove the battery. 2 P. 51
2. If the terminals are starting to corrode and
are coated with a white substance, wash
with warm water and wipe clean.

Continued 41
 Maintenance Fundamentals

3. If the terminals are heavily corroded, clean Fuses

and polish the terminals with a wire brush or
Fuses protect the electrical circuits on your
sandpaper. Wear safety glasses.
motorcycle. If something electrical on your
motorcycle stops working, check for and
replace any blown fuses. 2 P. 97
Maintenance

# Inspecting and Replacing Fuses

Turn the ignition switch to the OFF position to
remove and inspect fuses. If a fuse is blown,
replace with a fuse of the same rating. For fuse
4. After cleaning, reinstall the battery. ratings, see “Specifications.” 2 P. 114

Blown fuse
The battery has a limited life span. Consult your
dealer about when you should replace the
battery. Always replace the battery with another
maintenance-free battery of the same type.
NOTICE
Installing non-Honda electrical accessories can NOTICE
overload the electrical system, discharging the Replacing a fuse with one that has a higher
battery and possibly damaging the system. rating greatly increases the chance of damage to
the electrical system.

42
 Maintenance Fundamentals

If a fuse fails repeatedly, you likely have an *1.

The JASO T 903 standard is an index for engine
electrical fault. Have your motorcycle inspected oils for 4-stroke motorcycle engines. There are
by your dealer. two classes: MA and MB. For example, the
following label shows the MA classification.
Engine Oil
Oil code

Maintenance
Engine oil consumption varies and oil quality
deteriorates according to riding conditions and Oil classification
time elapsed.
Check the engine oil level regularly, and add the *2.
The SAE standard grades oils by their viscosity.
recommended engine oil if necessary. Dirty oil or *3.
The API classification specifies the quality and
old oil should be changed as soon as possible.
performance rating of engine oils. Use SG or
higher oils, excluding oils marked as “Energy
# Selecting the Engine Oil Conserving” or “Resource Conserving” on the
For recommended engine oil, see
circular API service symbol.
“Specifications.” 2 P. 113

If you use non-Honda engine oil, check the

label to make sure that the oil satisfies all of the
following standards:
● JASO T 903 standard*1: MA
● SAE standard*2: 10W-30
● API classification*3: SG or higher Not recommended Recommended

43
 Maintenance Fundamentals

Brake Fluid If the chain does not move smoothly, makes

strange noises, has damaged rollers, has loose
Do not add or replace brake fluid, except in an
pins, or kinks, have the chain inspected by your
emergency. Use only fresh brake fluid from a
sealed container. If you do add fluid, have the dealer.
brake system serviced by your dealer as soon as
Also inspect the drive sprocket and driven
Maintenance

possible.
sprocket. If either has worn or damaged teeth,
NOTICE
have the sprocket replaced by your dealer.
Brake fluid can damage plastic and painted surfaces
Wipe up spills immediately and wash thoroughly.

Recommended brake fluid:

Honda DOT 3 or DOT 4 Brake Fluid or
equivalent Normal Worn Damaged
(GOOD) (REPLACE) (REPLACE)

Drive Chain NOTICE

The drive chain must be inspected and Use of a new chain with worn sprockets will cause
lubricated regularly. Inspect the chain more rapid chain wear.
frequently if you often ride on bad roads, ride at
high speed, or ride with repeated fast
acceleration. 2 P. 70

44
 Maintenance Fundamentals

# Cleaning and Lubricating Never use petrol or low flash point solvents for
After inspecting the slack, clean the chain and cleaning the drive chain.
sprockets while rotating the rear wheel. Use a A fire or explosion could result.
dry cloth with high flash-point solvent. Use a Avoid getting lubricant on the brakes or tyres.
soft brush if the chain is dirty. Avoid applying excess chain lubricant to prevent
After cleaning, wipe dry and lubricate with the spray onto your clothes and the motorcycle.

Maintenance
recommended lubricant.

Recommended lubricant: Recommended Coolant

Drive chain lubricant Use only genuine HONDA PRE-MIX COOLANT
If not available, use SAE 80 or 90 gear without diluting with water. Genuine HONDA
oil. PRE-MIX COOLANT is excellent at preventing
corrosion and overheating.
The coolant should be inspected and replaced
properly by following the maintenance
schedule. 2 P. 35
NOTICE
Using coolant not specified for aluminium
engines or tap/mineral water can cause
corrosion.

45
 Maintenance Fundamentals

Crankcase Breather # Inspecting for Damage

Service more frequently when riding in rain, at Inspect the tyres for
full throttle, or after the motorcycle is washed or cuts, slits, or cracks that
overturned. Service if the deposit level can be exposes fabric or
seen in the transparent section of the drain cords, or nails or other
Maintenance

tube. foreign objects

If the drain tube overflows, the air filter may embedded in the side
become contaminated with engine oil causing of the tyre or the tread.
poor engine performance. 2 P. 78 Also inspect for any unusual bumps or bulges in
the side walls of the tyres.

Tyres (Inspecting/Replacing) # Inspecting for Abnormal Wear

Inspect the tyres for
# Checking the Air Pressure signs of abnormal wear
Visually inspect your tyres and use an air
pressure gauge to measure the air pressure at on the contact surface.
least once a month or any time you think the
tyres look low. Always check air pressure when
your tyres are cold.

46
 Maintenance Fundamentals

# Inspecting Tread Depth 3WARNING

Inspect the tread wear indicators. If they
become visible, replace the tyres immediately. Riding on tyres that are excessively
For safe riding, you should replace the tyres worn or improperly inflated can cause a
when the minimum tread depth is reached. crash in which you can be seriously hurt
or killed.

Maintenance
Follow all instructions in this owner's
or TWI manual regarding tyre inflation and
maintenance.

Wear indicator
location mark

Continued 47
 Maintenance Fundamentals

Have your tyres replaced by your dealer.

For recommended tyres, air pressure and 3WARNING
minimum tread depth, see “Specifications.” Installing improper tyres on your
2 P. 113
motorcycle can adversely affect
Follow these guidelines whenever you replace
handling and stability, and can cause a
tyres.
Maintenance

● Use the recommended tyres or equivalents

crash in which you can be seriously hurt
of the same size, construction, speed rating, or killed.
and load range.
● Have the wheel balanced with Honda Always use the size and type of tyres
Genuine balance weights or equivalent after recommended in this owner's manual.
the tyre is installed.
● Do not install a tube inside a tubeless tyre
on this motorcycle. Excessive heat build-up
can cause the tube to burst.
● Use only tubeless tyres on this motorcycle.
The rims are designed for tubeless tyres,
and during hard acceleration or braking, a
tube-type tyre could slip on the rim and
cause the tyre to rapidly deflate.

48
 Maintenance Fundamentals

Air Cleaner
This motorcycle is equipped with a viscous type
air cleaner element.
Air blow cleaning or any other cleaning can
degrade the viscous element performance and

Maintenance
cause the intake of dust.
Do not perform the maintenance. Should be
serviced by your dealer.

49
 Tool
The tool kit is stored under the rear seat.
2 P. 32

You can perform some roadside repairs, minor

adjustments and parts replacement with the
provided tools.
Maintenance

● 10 × 14 mm Open end wrench

● Spark plug wrench
● 5 mm Hex wrench
● Helmet set wire
● Fuse puller
● Extension bar
● Pin spanner

50
 Removing & Installing Body Components

Battery 2. Remove the bolt.

3. Disconnect the negative - terminal from
Terminal nut Negative terminal the battery.
4. Disconnect the positive + terminal from
Positive terminal
the battery.

Maintenance
Bolt
5. Remove the battery taking care not to
Battery drop the terminal nuts.

# Installation
Install the parts in the reverse order of
removal. Always connect the positive +
terminal first. Make sure that bolts and nuts
are tight.
Make sure the clock information is correct
Rubber strap Terminal nut after the battery is reconnected. 2 P. 19
For proper handling of the battery, see
# Removal “Maintenance Fundamentals.” 2 P. 40
“Battery Goes Dead.” 2 P. 93
Make sure the ignition switch is in the OFF
position.
1. Remove the front seat. 2 P. 53
51
 Removing & Installing Body Components u Clip

Clip # Installation
# Removal
Centre pin
Maintenance

1. Push the bottom of the centre pin.

2. Insert the clip into the hole.
1. Press down on the centre pin to release 3. Press down on the centre pin to lock the
the lock. clip.
2. Pull the clip out of the hole.

52
 Removing & Installing Body Components u Front Seat

Front Seat 3. Remove the mounting bolts and collars,

and then pull the front seat back and up.
# Removal Mounting
1. Remove the rear seat. 2 P. 58 bolts
2. Remove the bolts, washers and clips, and Collar

Maintenance
then pull the seat lock cover back and up. Front seat
Collar
Clips Tab

Bolts

Washers

Hooks
Hooks

Recess
Seat lock
cover Guides

Continued 53
 Removing & Installing Body Components u Front Seat

# Installation
1. Install the front seat while inserting the
tab into the recess.
2. Install the collars and mounting bolts.
3. Tighten the mounting bolts securely.
Maintenance

4. Install the seat lock cover while inserting

the hooks into the guides.
5. Install and tighten the bolts and washers.

Torque: 4.2 N·m (0.4 kgf·m, 3.1 lbf·ft)

6. Install the clips.

7. Install the rear seat.
Make sure that the seat is locked securely
in position by pulling it up lightly.

54
 Removing & Installing Body Components u Harness Band Clip

Harness Band Clip # Installation

Install the harness band clip until it seats
# Removal properly.
Pull the harness band clip while pressing
both side of the anchor.

Maintenance
55
 Removing & Installing Body Components u Right Middle Cowl

Right Middle Cowl 4. Release the tabs from the slots.

5. Release the prongs from the grommets.
6. Remove the right middle cowl while
# Removal releasing the harness band clip. 2 P. 55
1. Remove the front seat. 2 P. 53 u Be careful not to damage the wire
2. Remove the clip. 2 P. 52 harness.
Maintenance

3. Remove the bolts A and bolts B. u Be careful not to apply weight to the
Bolts A right middle cowl.
Prongs Grommets

Slots

Tabs
Bolts B
Prong

Bolts B
Harness band clip
Clip
Right middle cowl Wire harness

56
 Removing & Installing Body Components u Right Middle Cowl

# Installation
1. To install the right middle cowl, reverse
the removal procedure.
2. Install and tighten the the bolts A
securely.

Maintenance
3. Install and tighten the bolts B.

Torque: 4.2 N·m (0.4 kgf·m, 3.1 lbf·ft)

4. Install the clip

Check that the turn signals function properly
after you install the right middle cowl.

57
Rear Seat
 Spark Plug

Checking Spark Plug Spark plug wrench

For the recommended spark plug, see

“Specifications.” 2 P. 113

Maintenance
Use only the recommended type of spark
plug in the recommended heat range.
NOTICE
Using a spark plug with an improper heat range
can cause engine damage.
Spark plug cap
1. Remove the right middle cowl. 2 P. 56
2. Disconnect the spark plug cap from the
5. Inspect the electrodes and centre
spark plug.
porcelain for deposits, erosion or carbon
3. Clean any dirt from around the spark plug
fouling.
base.
u If the erosion or deposit is heavy,
4. Remove the spark plug using provided
replace the plug.
spark plug wrench. 2 P. 50
u Clean a carbon or wet-fouled plug
with a plug cleaner, otherwise use a
wire brush.

Continued 59
 Spark Plug u Checking Spark Plug

6. Check the spark plug gap using a wire- 9. Tighten the spark plug:
type feeler gauge. ● If the old plug is good:
u If adjustment is necessary, bend the 1/8 turn after it seats
side electrode carefully. ● If installing a new plug, tighten it twice
to prevent loosening:
The gap should be:
Maintenance

a) First, tighten the plug:

0.8 - 0.9 mm (0.03 - 0.04 in)
NGK: 1/2 turn after it seats.
DENSO: 3/4 turn after it seats.
Side electrode b) Then loosen the plug.
c) Next, tighten the plug again:
1/8 turn after it seats
Spark plug gap NOTICE
Plug washer An improperly tightened spark plug can damage
the engine. If a plug is too loose, a piston may be
damaged. If a plug is too tight, the threads may
be damaged.
7. Make sure the plug washer is in good
condition. 10. Install the parts in the reverse order of
8. Install the spark plug. With the plug removal.
washer attached, thread the spark plug in u When reinstalling the spark plug cap,
by hand to prevent cross-threading. take care to avoid pinching any cables
or wires.
60
 Engine Oil

Checking the Engine Oil Oil fill cap/dipstick

1. If the engine is cold, idle the engine for 3 Upper level

to 5 minutes.
2. Turn the ignition switch to the OFF

Maintenance
position and wait for 2 to 3 minutes.
3. Place your motorcycle in an upright
position on a firm, level surface. Lower level
4. Remove the oil fill cap/dipstick and wipe it
clean.
5. Insert the oil fill cap/dipstick until it seats,
but don't screw it in.
6. Check that the oil level is between the
upper level and lower level marks on the
oil fill cap/dipstick.
7. Securely install the oil fill cap/dipstick.

61
 Engine Oil u Adding Engine Oil

Adding Engine Oil 2. Securely reinstall the oil fill cap/dipstick.

NOTICE
If the engine oil is below or near the lower Overfilling with oil or operating with insufficient
level mark, add the recommended engine oil. oil can cause damage to your engine. Do not mix
2 P. 43, 2 P. 113 different brands and grades of oil. They may
Maintenance

1. Remove the oil fill cap/dipstick. Add the affect lubrication and clutch operation.
recommended oil until it reaches the For the recommended oil and oil selection
upper level mark. guidelines, see “Maintenance Fundamentals.”
u Place your motorcycle in an upright 2 P. 43
position on a firm, level surface when
checking the oil level.
u Do not overfill above the upper level
mark.
u Make sure no foreign objects enter the
oil filler opening.
u Wipe up any spills immediately.

62
 Engine Oil u Changing Engine Oil

Changing Engine Oil 5. Remove the oil fill cap/dipstick, drain bolt
and sealing washer to drain the oil.
Changing the oil requires special tools. We u Discard the oil at an approved
recommend that you have your motorcycle recycling centre.
serviced by your dealer. 6. Install a new sealing washer onto the

Maintenance
1. If the engine is cold, idle the engine for 3 drain bolt. Tighten the drain bolt.
to 5 minutes.
Torque: 24 N·m (2.4 kgf·m, 18 lbf·ft)
2. Turn the ignition switch to the OFF
position and wait for 2 to 3 minutes. 7. Fill the crankcase with the recommended
3. Place your motorcycle on a firm, level oil (2 P. 43, 2 P. 113) and install the oil fill
surface. cap/dipstick.
4. Place a drain pan under the drain bolt.
Required oil
Sealing washer When changing oil:
1.1 L (1.2 US qt, 1.0 Imp qt)

8. Check the oil level. 2 P. 61

9. Check that there are no oil leaks.

Drain bolt

63
 Coolant

Checking the Coolant UPPER level

Check the coolant level in the reserve tank
while the engine is cold.
Maintenance

1. Place your motorcycle on a firm, level

surface.
2. Hold your motorcycle in an upright
position.
3. Check that the coolant level is between LOWER level
Reserve tank
the UPPER level and LOWER level marks
on the reserve tank.
Adding Coolant
If the coolant level is dropping noticeably or
the reserve tank is empty, you likely have a If the coolant level is below the LOWER level
serious leak. Have your motorcycle inspected mark, add the recommended coolant
by your dealer. (2 P. 45) until the level reaches the UPPER
level mark.
Add fluid only from the reserve tank cap and
do not remove the radiator cap.

64
 Coolant u Changing Coolant

1. Remove the reserve tank cap and add Reserve tank cap
fluid while monitoring the coolant level.
u Do not overfill above the UPPER level
mark.
u Make sure no foreign objects enter the

Maintenance
reserve tank opening.
2. Securely reinstall the reserve tank cap.

3WARNING
Reserve tank
Removing the radiator cap while the
engine is hot can cause the coolant to
spray out, potentially scalding you.
Changing Coolant
Always let the engine and radiator cool
down before removing the radiator cap. Have your dealer change the coolant unless
you have the proper tools and are
mechanically qualified.

65
 Brakes

Checking Brake Fluid If the brake fluid level in either reservoir is

below the LWR mark or LOWER level mark or
1. Place your motorcycle in an upright the brake lever and pedal freeplay becomes
position on a firm, level surface. excessive, inspect the brake pads for wear.
2. Front Check that the brake fluid reservoir If the brake pads are not worn, you most
Maintenance

is horizontal and that the fluid level is likely have a leak. Have your motorcycle
above the LWR mark. inspected by your dealer.
Rear Check that the brake fluid reservoir
is horizontal and that the fluid level is
between the LOWER level and UPPER
level marks.
Front Rear
Front brake fluid reservoir Rear brake fluid reservoir

UPPER level mark

LWR mark LOWER level mark

66
 Brakes u Inspecting the Brake Pads

Inspecting the Brake Pads Front Rear

Brake Pads Brake Pads

Check the condition of the brake pad wear
indicators.
The pads need to be replaced if a brake pad

Maintenance
is worn to the indicator.
1. Front Inspect the brake pads from below
the brake caliper.
2. Rear Inspect the brake pads from the rear
right of the motorcycle.
If necessary have the pads replaced by your Disc
dealer. Disc
Always replace both left and right brake pads Wear indicators
at the same time. Wear indicator Wear indicator

67
 Brakes u Adjusting the Brakelight Switch

Adjusting the Brakelight Switch Brakelight switch

Check the operation of the brakelight switch.

Hold the brakelight switch and turn the
adjusting nut in the direction A if the switch
Maintenance

operates too late, or turn the nut in the B A

direction B if the switch operates too soon.

Adjusting nut

68
 Side Stand

Checking the Side Stand

Maintenance
Side stand spring

1. Check that the side stand operates

smoothly. If the side stand is stiff or
squeaky, clean the pivot area and
lubricate the pivot bolt with clean grease.
2. Check the spring for damage or loss of
tension.

69
 Drive Chain

Inspecting the Drive Chain

Slack
Check the drive chain slack at several points
along the chain. If the slack is not constant at
Maintenance

all points, some links may be kinked and

binding.
Have the chain inspected by your dealer.

1. Shift the transmission to Neutral. Stop the

engine.
2. Place your motorcycle on its side stand on 4. Roll the motorcycle forward and check
a firm, level surface. that the chain moves smoothly.
3. Check the slack in the lower half of the 5. Inspect the sprockets. 2 P. 44
drive chain midway between the 6. Clean and lubricate the drive chain.
sprockets. 2 P. 45
Drive chain slack:
25 - 35 mm (1.0 - 1.4 in)
u Do not ride your motorcycle if the
slack exceeds 50 mm (2.0 in).

70
 Drive Chain u Adjusting the Drive Chain Slack

Adjusting the Drive Chain Slack CBR150RA Rear axle nut

Pulser ring
Adjusting the chain requires special tools.
Have the drive chain slack adjusted by your
dealer. Lock nut

Maintenance
CBR150RA
When adjusting the drive chain slack, be
careful not to damage the wheel speed
sensor and pulser ring. Adjusting nut

1. Shift the transmission to Neutral. Stop the Chain adjuster

Adjusting nut index mark
engine.
2. Place your motorcycle on its side stand on
a firm, level surface.
3. Loosen the rear axle nut.
4. Loosen the lock nuts on both sides of the
swingarm.

Lock nut
Rear edge of adjusting slot

Continued 71
 Drive Chain u Adjusting the Drive Chain Slack

5. Turn both adjusting nuts an equal 7. Tighten the rear axle nut.
number of turns until the correct drive
Torque: 68 N·m (6.9 kgf·m, 50 lbf·ft)
chain slack is obtained. Turn the adjusting
nuts clockwise to tighten the chain. Turn 8. Tighten the drive chain adjusting nuts
the adjusting nuts counterclockwise to lightly, then hold the adjusting nuts and
Maintenance

provide more slack. tighten the lock nuts.

Adjust the slack at a point midway 9. Recheck drive chain slack.
between the front sprocket and the rear
wheel sprocket. If a torque wrench was not used for
Check the drive chain slack. 2 P. 70 installation, see your dealer as soon as
6. Check rear axle alignment by making sure possible to verify proper assembly.
the chain adjuster index marks align with Improper assembly may lead to loss of
the rear edge of the adjusting slots. braking capacity.
Both marks should correspond. If the axle
is misaligned, turn the right or left
adjusting nuts until the marks are aligned
and recheck chain slack.

72
 Drive Chain u Adjusting the Drive Chain Slack

# Checking the Drive Chain Wear

If the drive chain slack is excessive when the
rear axle is moved to the furthest limit of
adjustment, the drive chain is worn and must
be replaced.

Maintenance
Chain:
FSCM428H or KMC428HG

If necessary have the drive chain replaced by

your dealer.

73
 Clutch

Checking the Clutch Check the clutch cable for kinks or signs of
wear. If necessary have it replaced by your
# Checking the Clutch Lever Freeplay dealer.
Check the clutch lever freeplay. Lubricate the clutch cable with a
commercially available cable lubricant to
Maintenance

Freeplay at the clutch lever: prevent premature wear and corrosion.

10 - 20 mm (0.4 - 0.8 in)
NOTICE
Improper freeplay adjustment can cause
Clutch lever premature clutch wear.

Freeplay

74
 Clutch u Adjusting the Clutch Lever Freeplay

Adjusting the Clutch Lever Upper clutch cable adjuster

Upper lock nut
Freeplay
–
# Upper Adjustment

Maintenance
Attempt adjustment with the upper clutch +
cable adjuster first.

1. Pull back the rubber dust cover.

2. Loosen the upper lock nut. Rubber dust cover
3. Turn the upper clutch cable adjuster until
the freeplay is 10 - 20 mm (0.4 - 0.8 in).
4. Tighten the upper lock nut and check the
freeplay again.
5. Install the rubber dust cover.

Continued 75
 Clutch u Adjusting the Clutch Lever Freeplay

# Lower Adjustment Lower adjusting nut

If the upper clutch cable adjuster is threaded
out near its limit, or the correct freeplay
cannot be obtained, attempt adjustment with +
the lower clutch cable adjusting nut.
Maintenance

1. Loosen the upper lock nut and turn the

upper clutch cable adjuster all the way in –
(to provide maximum freeplay). Tighten
the upper lock nut.
2. Loosen the lower lock nut. Lower lock nut
3. Turn the lower adjusting nut until the
If proper adjustment cannot be obtained or
clutch lever freeplay is 10 - 20 mm (0.4 -
0.8 in). the clutch does not work correctly, see your
4. Tighten the lower lock nut and check the dealer.
clutch lever freeplay.
5. Start the engine, pull the clutch lever in,
and shift into gear. Make sure the engine
does not stall and the motorcycle does
not creep. Gradually release the clutch
lever and open the throttle. Your
motorcycle should move smoothly and
accelerate gradually.
76
 Throttle

Checking the Throttle

With the engine off, check that the throttle
rotates smoothly from fully closed to fully
open in all steering positions and throttle

Maintenance
freeplay is correct. If the throttle does not
move smoothly, close automatically, or if the
cable is damaged, have the motorcycle
inspected by your dealer.
Freeplay at the throttle grip flange:
2 - 6 mm (0.1 - 0.2 in)

Freeplay

Flange

77
 Crankcase Breather

Cleaning the Crankcase

Breather
1. Place a suitable container under the
crankcase breather tube.
Maintenance

2. Remove the crankcase breather tube plug

from the tube.
3. Drain deposits into a suitable container.
4. Install the crankcase breather tube plug.

Crankcase breather tube plug

78
 Other Adjustments

Adjusting the Headlight Aim Right side Pinion

You can adjust vertical aim of the headlight

for proper alignment. Turn the pinion in or
out as necessary using a Phillips screwdriver.

Maintenance
Obey local laws and regulations.
Left side Pinion

Lower

Raise

Raise
Lower

79
 Other Adjustments u Adjusting the Front Suspension

Adjusting the Front Suspension

Fork bolt top
# Spring Preload surface
Adjuster
You can adjust the spring preload by the
adjuster to suit the load or the road surface.
Maintenance

Turn clockwise to increase spring preload

(hard), or turn counterclockwise to decrease
spring preload (soft). 3rd groove
The standard position is the 3rd groove from
the top aligning with the top surface of the
fork bolts. NOTICE
Do not turn the adjuster beyond its limits.
Adjust both left and right forks to the same
spring preload.

80
 Other Adjustments u Adjusting the Rear Suspension

Adjusting the Rear Suspension Adjuster

# Spring Preload
You can adjust the spring preload by the
adjuster to suit the load or the road surface.

Maintenance
1 2 3 4 5
Turn the adjuster using the pin spanner and
extension bar provided in the tool kit. 2 P. 50
The preload adjuster has 5 positions.
Position 1 is for a decreased spring preload
(soft), or turn to the position 3 to 5 for a
increased spring preload (hard). The
standard position is 2. Extension bar Pin spanner

NOTICE
Attempting to adjust directly from 1 to 5 or 5 to 1
may damage the shock absorber.
Do not turn the adjuster beyond its limits.

81
Troubleshooting

Engine Will Not Start........................................ P. 83 Unstable Engine Operation Occurs

Overheating (High coolant temperature Intermittently ................................................... P. 99
indicator is on) ................................................. P. 84
Warning Indicators On or Flashing............... P. 85
PGM-FI (Programmed Fuel Injection)
Malfunction Indicator Lamp (MIL)................. P. 85
ABS (Anti-lock Brake System) Indicator ......... P. 85
Other Warning Indications.............................. P. 86
Fuel Gauge Failure Indication........................... P. 86
Tyre Puncture ..................................................... P. 87
Electrical Trouble ............................................... P. 93
Battery Goes Dead .............................................. P. 93
Burned-out Light Bulb........................................ P. 93
Blown Fuse ............................................................ P. 97
 Engine Will Not Start

Starter Motor Operates But Starter Motor Does Not

Engine Does Not Start Operate
Check the following items: Check the following items:
● Check the correct engine starting ● Check the correct engine starting
sequence. 2 P. 26 sequence. 2 P. 26

Troubleshooting
● Check that there is petrol in the fuel tank. ● Check for a blown fuse. 2 P. 97
● Check if the PGM-FI malfunction indicator ● Check for a loose battery connection
lamp (MIL) is on. (2 P. 51) or battery terminal corrosion
u If the indicator lamp is on, contact (2 P. 40).
your dealer as soon as possible. ● Check the condition of the battery.
2 P. 93
If the problem continues, have your
motorcycle inspected by your dealer.

83
 Overheating (High coolant temperature indicator is on)
The engine is overheating when the following 2. Check that the radiator fan is operating,
occurs: and then turn the ignition switch to the
● High coolant temperature indicator OFF position.
comes on. If the fan is not operating:
● Acceleration becomes sluggish. Suspect a fault. Do not start the engine.
If this occurs, pull safely to the side of the Transport your motorcycle to your dealer.
road and perform the following If the fan is operating:
Troubleshooting

procedure. Allow the engine to cool with the ignition

Extended fast idling may cause the high switch in the OFF position.
coolant temperature indicator to come on. 3. After the engine has cooled, inspect the
NOTICE radiator hose and check if there is a leak.
Continuing to ride with an overheated engine 2 P. 64
can cause serious damage to the engine. If there is a leak:
Do not start the engine. Transport your
1. Stop the engine using the ignition switch, motorcycle to your dealer.
and then turn the ignition switch to the 4. Check the coolant level in the reserve
ON position. tank. 2 P. 64
u Add coolant as necessary.
5. If 1-4 check normal, you may continue
riding, but closely monitor the high
coolant temperature indicator.
84
 Warning Indicators On or Flashing

PGM-FI (Programmed Fuel ● Indicator comes on or starts flashing while

riding.
Injection) Malfunction ● Indicator does not come on when the
Indicator Lamp (MIL) ignition switch is in the ON position.
● Indicator does not go off at speeds above
If the indicator comes on while riding, you 10 km/h (6 mph).
may have a serious problem with the PGM-FI If the ABS indicator stays on, your brakes will

Troubleshooting
system. Reduce speed and have your continue to work as a conventional system,
motorcycle inspected by your dealer as soon but without the anti-locking function.
as possible.
The ABS indicator may flash if you turn the
ABS (Anti-lock Brake System) rear wheel while the rear wheel is lifted off
Indicator the ground. In this case, turn the ignition
switch to the OFF position, and then to the
CBR150RA
ON position again. The ABS indicator will go
If the indicator operates in one of the
off after your speed reaches 30 km/h (19
following ways, you may have a serious
mph).
problem with the ABS. Reduce your speed
and have your motorcycle inspected by your
dealer as soon as possible.

85
 Other Warning Indications

Fuel Gauge Failure Indication

If the fuel system has an error, the fuel gauge
indicators will be displayed as shown in the
illustration.
If this occurs, see your dealer as soon as
possible.
Troubleshooting

86
 Tyre Puncture
Repairing a puncture or removing a wheel
3WARNING
requires special tools and technical expertise.
Riding your motorcycle with a
We recommend you have this type of service
temporary tyre repair can be risky. If the
performed by your dealer.
temporary repair fails, you can crash
After an emergency repair, always have the
and be seriously injured or killed.
tyre inspected/replaced by your dealer.

Troubleshooting
If you must ride with a temporary tyre
Emergency Repair Using a Tyre repair, ride slowly and carefully and do
not exceed 50 km/h (30 mph) until the
Repair Kit tyre is replaced.
If your tyre has a minor puncture, you can
make an emergency repair using a tubeless Removing Wheels
tyre repair kit.
Follow the instructions provided with the Follow these procedures if you need to
emergency tyre repair kit. remove a wheel in order to repair a
puncture.
Riding your motorcycle with a temporary tyre
CBR150RA
repair is very risky. Do not exceed 50 km/h
(30 mph). Have the tyre replaced by your When removing and installing the wheel, be
dealer as soon as possible. careful not to damage the wheel speed
sensor and pulser ring.
Continued 87
 Tyre Puncture u Removing Wheels

# Front Wheel 4. Remove the front axle nut, front axle

Removal shaft, front wheel and side collars.
1. Place your motorcycle on a firm, level u Avoid getting grease, oil, or dirt on the
surface. disc or pad surfaces.
2. Loose the front axle nut. u Do not pull the brake lever while the
wheel is removed.
Side collar
Troubleshooting

Side collar

Front axle nut

3. Support your motorcycle securely and

raise the front wheel off the ground using Front axle shaft CBR150RA
a maintenance stand or a hoist. Pulser ring

88
 Tyre Puncture u Removing Wheels

Installation If a torque wrench was not used for

1. Attach the side collars to the front wheel. installation, see your dealer as soon as
2. Position the front wheel between the fork possible to verify proper assembly.
legs and insert the front axle shaft from Improper assembly may lead to loss of
the right side, through the right fork leg braking capacity.
and wheel hub.

Troubleshooting
NOTICE
When installing a wheel or caliper into original
position, carefully fit the brake disc between the
pads to avoid scratching them.

3. Tighten the front axle nut.

Torque: 59 N·m (6.0 kgf·m, 44 lbf·ft)

4. After installing the wheel, apply the brake

lever several times, then check if the
wheel rotates freely. Recheck the wheel if
the brake drags or if the wheel dose not
rotate freely.

Continued 89
 Tyre Puncture u Removing Wheels

# Rear Wheel 4. Remove the drive chain from the rear

Removal wheel sprocket by pushing the rear wheel
1. Support your motorcycle securely and forward.
raise the rear wheel off the ground using
a maintenance stand or a hoist. Side collar Adjusting nut
2. Loosen the rear axle nut, lock nuts and
Troubleshooting

turn the adjusting nuts so the rear wheel

can be moved all the way forward for
maximum drive chain slack.
3. Remove the rear axle nut. Drive chain

CBR150RA
Rear axle nut
Pulser ring

Rear axle shaft Lock nut

Lock nut

Side collar

Adjusting nut

90
 Tyre Puncture u Removing Wheels

5. Remove the rear axle shaft, side collars NOTICE

and rear wheel. When installing a wheel or caliper into original
u Support the brake caliper assembly so position, carefully fit the brake disc between the
that it doesn’t hang from the brake pads to avoid scratching them.
hose. Do not twist the brake hose. 2. Make sure that the slot on the brake
u Avoid getting grease, oil, or dirt on the caliper bracket is positioned in the lug on
disc or pad surfaces.

Troubleshooting
the swingarm.
u Do not push the brake pedal while the
Brake caliper bracket
brake caliper is removed.
Lug
Installation
1. To install the rear wheel, reverse the
removal procedure.
u Take care to prevent the brake caliper
from scratching the wheel during
installation. Slot
Swingarm

Continued 91
 Tyre Puncture u Removing Wheels

3. Adjust the drive chain. 2 P. 71

4. Install and tighten the rear axle nut.

Torque: 68 N·m (6.9 kgf·m, 50 lbf·ft)

5. Tighten the drive chain adjusting nuts

lightly, then hold the adjusting nuts and
tighten the lock nuts.
Troubleshooting

6. After installing the wheel, apply the brake

pedal several times, then check if the
wheel rotates freely. Recheck the wheel if
the brake drags or if the wheel does not
rotate freely.

If a torque wrench was not used for

installation, see your dealer as soon as
possible to verify proper assembly.
Improper assembly may lead to loss of
braking capacity.

92
 Electrical Trouble

Battery Goes Dead Burned-out Light Bulb

Charge the battery using a motorcycle All light bulbs on the motorcycle are LEDs. If
battery charger. there is an LED which is not turned on, see
Remove the battery from the motorcycle your dealer for servicing.
before charging.
Do not use an automobile-type battery

Troubleshooting
charger, as these can overheat a motorcycle
battery and cause permanent damage. If the
battery does not recover after recharging,
contact your dealer.
NOTICE
Jump starting using an automobile battery can
damage your motorcycle's electrical system and
is not recommended.

Continued 93
 Electrical Trouble u Burned-out Light Bulb

# Headlight # Position Light

Position lights
Troubleshooting

Headlights

The headlights use several LEDs. The position lights use several LEDs.
If there is an LED which is not turned on, see If there is an LED which is not turned on, see
your dealer for servicing. your dealer for servicing.

94
 Electrical Trouble u Burned-out Light Bulb

# Brakelight/Taillight # Front/Rear Turn Signal Light

Troubleshooting
Brakelight/Taillight Turn signal light

The brakelight and taillight uses several LEDs. The front and rear turn signal lights use an
If there is an LED which is not turned on, see LED.
your dealer for servicing. If the LED not turned on, see your dealer for
servicing.

Continued 95
 Electrical Trouble u Burned-out Light Bulb

# License Plate Light

Troubleshooting

License plate light

The license plate light uses an LED.

If the LED not turned on, see your dealer for
servicing.

96
 Electrical Trouble u Blown Fuse

Blown Fuse Fuse box

cover
Before handling fuses, see “Inspecting and
Replacing Fuses.” 2 P. 42

# Fuse Box Fuses Spare

1. Remove the front seat. 2 P. 53

Troubleshooting
fuses
2. Open the fuse box cover.
3. Pull the fuses out one by one with the
fuse puller in the tool kit and check for a
blown fuse. Always replace a blown fuse
with a spare fuse of the same rating.
4. Close the fuse box cover.
5. Reinstall parts in the reverse order of
removal.

Continued 97
 Electrical Trouble u Blown Fuse

# ABS Fuse
CBR150RA
Fuse case
covers
1. Remove the front seat. 2 P. 53
2. Open the fuse case covers. ABS main
fuse
3. Pull the ABS fuses out one by one with
the fuse puller in the tool kit and check for ABS motor ABS sol fuse
fuse
Troubleshooting

a blown fuse. Always replace a blown fuse

with a spare fuse of the same rating.
4. Close the fuse case covers.
5. Reinstall parts in the reverse order of
removal.

NOTICE
If a fuse fails repeatedly, you likely have an
electrical problem. Have your motorcycle
inspected by your dealer.

98
 Unstable Engine Operation Occurs Intermittently
If the fuel pump filter is clogged, unstable
engine operation will occur intermittently
while riding.
Even if this symptom occurs, you can
continue to ride your motorcycle.
If unstable engine operation occurs even if
sufficient fuel is available, have your

Troubleshooting
motorcycle inspected by your dealer as soon
as possible.

99
Information

Keys..................................................................... P. 101
Instruments, Controls, & Other Features... P. 102
Caring for Your Motorcycle .......................... P. 103
Storing Your Motorcycle ............................... P. 106
Transporting Your Motorcycle..................... P. 107
You & the Environment ................................. P. 108
Serial Numbers ................................................ P. 109
Fuels Containing Alcohol .............................. P. 110
Catalytic Converter ......................................... P. 111
 Keys

Keys
Ignition Key
Be sure to record the key number provided with
the original keys. Store the spare key and key
number in a safe location.
To make a duplicate, take the spare key or the
key number to your dealer.
If you lose all ignition keys and the key number,

Information
the ignition switch assembly will probably have
to be removed by your dealer to determine the
key number.

A metal key holder may cause damage to the

area surrounding the ignition switch.

101
 Instruments, Controls, & Other Features

Instruments, Controls, & Ignition Cut-off System

Other Features A banking (lean angle) sensor automatically
stops the engine and fuel pump if the
Ignition Switch motorcycle falls over. To reset the sensor, you
Leaving the ignition switch in the ON position must turn the ignition switch to the OFF position
with the engine stopped will drain the battery. and back to the ON position before the engine
Do not turn the key while riding. can be restarted.
Information

Odometer
The display locks at 999,999 when the read-out
exceeds 999,999.

Tripmeter
The tripmeters return to 0.0 when each read-
out exceeds 9,999.9.

Document Bag
The owner's manual, registration, and insurance
information can be stored in the plastic
document bag located under the rear seat.
102
 Caring for Your Motorcycle

Caring for Your Motorcycle 3. Thoroughly rinse your motorcycle with

plenty of clean water and dry with a soft,
Frequent cleaning and polishing is important to clean cloth.
ensure the life of your Honda. A clean 4. After the motorcycle dries, lubricate any
motorcycle makes it easier to spot potential moving parts.
problems. u Make sure that no lubricant spills onto
In particular, seawater and salts used to prevent
ice on roads promote the formation of the brakes or tyres. Brake discs, pads,
corrosion. Always wash your motorcycle drum or shoes contaminated with oil will
thoroughly after riding on coastal or treated suffer greatly reduced braking

Information
roads. effectiveness and can lead to a crash.
5. Lubricate the drive chain immediately after
Washing washing and drying the motorcycle.
Allow the engine, muffler, brakes, and other 6. Apply a coat of wax to prevent corrosion.
high-temperature parts to cool before washing. u Avoid products that contain harsh
1. Rinse your motorcycle thoroughly using a low detergents or chemical solvents. These
pressure garden hose to remove loose dirt. can damage the metal, paint, and plastic
2. If necessary, use a sponge or a soft towel on your motorcycle.
with mild cleaner to remove road grime. Keep the wax clear of the tyres and
u Clean the windscreen, headlight lens, brakes.
panels, and other plastic components u If your motorcycle has any mat painted
with extra care to avoid scratching them. parts, do not apply a coat of wax to the
Avoid directing water into the air cleaner, mat painted surface.
muffler, and electrical parts.
Continued 103
 Caring for Your Motorcycle

# Washing Precautions ● Do not direct water at the air cleaner:

Follow these guidelines when washing: u Water in the air cleaner can prevent the
● Do not use high-pressure washers: engine from starting.
u High-pressure water cleaners can ● Do not direct water near the headlight:
damage moving parts and electrical u The headlight's inside lens may fog
parts, rendering them inoperable. temporarily after washing or while riding
u Water in the air intake can be drawn into in the rain. This does not impact the
the throttle body and/or enter the air headlight function.
cleaner. However, if you see a large amount of
Information

● Do not direct water at the muffler: water or ice accumulated inside the
u Water in the muffler can prevent starting lens(es), have your vehicle inspected by
and causes rust in the muffler. your dealer.
● Dry the brakes: ● Do not use wax or polishing compounds on
u Water adversely affects braking mat painted surface:
effectiveness. After washing, apply the u Use a soft cloth or sponge, plenty of
brakes intermittently at low speed to water, and a mild detergent to clean mat
help dry them. painted surfaces. Dry with a soft clean
● Do not direct water under the seat: cloth.
u Water in the underseat compartment
can damage your documents and other
belongings.

104
 Caring for Your Motorcycle

Aluminium Components Panels

Aluminium will corrode from contact with dirt, Follow these guidelines to prevent scratches
mud, or road salt. Clean aluminium parts and blemishes:
regularly and follow these guidelines to avoid ● Wash gently using a soft sponge and plenty
scratches: of water.
● Do not use stiff brushes, steel wool, or ● To remove stubborn stains, use diluted
cleaners containing abrasives. detergent and rinse thoroughly with plenty
● Avoid riding over or scraping against curbs. of water.
● Avoid getting petrol, brake fluid, or

Information
detergents on the instruments, panels, or
headlight.

Windscreen
Using plenty of water, clean the windscreen with
a soft cloth or sponge. (Avoid using detergents
or any kind of chemical cleaner on the
windscreen.) Dry with a soft, clean cloth.
NOTICE
To avoid possible scratching or other damage,
use only water and a soft cloth or sponge to
clean the windscreen.

Continued 105
 Storing Your Motorcycle

For a dirtier windscreen, use a diluted neutral Storing Your Motorcycle

detergent with a sponge and plenty of water.
Make sure to wash off all the detergent. If you store your motorcycle outdoors, you
(Detergent residue may cause windscreen should consider using a full-body motorcycle
cracks.) cover.
If you won't be riding for an extended period,
Replace the windscreen if scratches cannot be follow these guidelines:
removed and they obstruct clear vision. ● Wash your motorcycle and wax all painted
surfaces (except mat painted surfaces). Coat
Information

Take care to keep battery electrolyte, brake chrome pieces with rust-inhibiting oil.
fluid, or other chemical solvents off the ● Lubricate the drive chain. 2 P. 44
windscreen and screen garnish. They will ● Place your motorcycle on a maintenance
damage the plastic. stand and position a block so that both tyres
are off the ground.
● After rain, remove the body cover and allow
Exhaust Pipe and Muffler the motorcycle to dry.
When the exhaust pipe and muffler are painted, ● Remove the battery (2 P. 51) to prevent
do not use a commercially available abrasive discharge. Fully charge the battery and then
kitchen cleaning compound. Use a neutral place it in a shaded, well-ventilated area.
detergent to clean the painted surface on the u If you leave the battery in place,
exhaust pipe and muffler. If you are not sure if disconnect the negative - terminal to
your exhaust pipe and muffler are painted, prevent discharge.
contact your dealer.
106
 Transporting Your Motorcycle

After removing your motorcycle from storage, Transporting Your

inspect all maintenance items required by the
Maintenance Schedule.
Motorcycle
If your motorcycle needs to be transported, it
should be carried on a motorcycle trailer or a
flatbed truck or trailer that has a loading ramp
or lifting platform, and motorcycle tie-down
straps. Never try to tow your motorcycle with a
wheel or wheels on the ground.

Information
NOTICE
Towing your motorcycle can cause serious
damage to the transmission.

107
 You & the Environment

You & the Environment Recycle Wastes

Put oil and other toxic wastes in approved
Owning and riding a motorcycle can be
containers and take them to a recycling centre.
enjoyable, but you must do your part to protect
Call your local or state office of public works or
the environment.
environmental services to find a recycling centre
in your area, and to get instructions on how to
Choose Sensible Cleaners dispose of non-recyclable wastes. Do not place
used engine oil in the trash, or pour it down a
Use a biodegradable detergent when you wash
drain or on the ground. Used oil, petrol,
Information

your motorcycle. Avoid aerosol spray cleaners

coolant, and cleaning solvents contain poisons
that contain chlorofluorocarbons (CFCs) which
that can hurt refuse workers and contaminate
damage the atmosphere's protective ozone
drinking water, lakes, rivers, and oceans.
layer.

108
 Serial Numbers

Serial Numbers
The frame and engine serial numbers uniquely
identify your motorcycle and are required in
order to register your motorcycle. They may
also be required when ordering replacement
parts.
You should record these numbers and keep
them in a safe place.

Information
Frame number

Engine number

109
 Fuels Containing Alcohol

Fuels Containing Alcohol The use of petrol containing more than 10%
ethanol may:
Some conventional fuels blended with alcohol ● Damage the painting of the fuel tank.
are available in some locales to help reduce ● Damage the rubber tubes of the fuel line.
emissions to meet clean air standards. If you ● Cause corrosion of the fuel tank.
plan to use blended fuel, check that it is ● Cause poor drivability.
unleaded and meets the minimum octane
NOTICE
rating requirement.
Use of blended fuels containing higher than
approved percentages can damage metal,
Information

The following fuel blends can be used in your rubber, plastic parts of your fuel system.
motorcycle:
● Ethanol (ethyl alcohol) up to 10% by volume. If you notice any undesirable operating
u Petrol containing ethanol may be symptoms or performance problems, try a
marketed under the name Gasohol. different brand of petrol.

110
 Catalytic Converter

Catalytic Converter Follow these guidelines to protect your

motorcycle's catalytic converter.
This motorcycle is equipped with a three-way ● Always use unleaded petrol. Leaded petrol
catalytic converter. The catalytic converter will damage the catalytic converter.
contains precious metals that serve as catalysts ● Keep the engine in good running condition.
in high temperature chemical reactions that ● Have your motorcycle serviced if your
convert hydrocarbons (HC), carbon monoxide engine is misfiring, backfiring, stalling, or
(CO), and oxides of nitrogen (NOx) in the otherwise not running properly, stop riding
exhaust gasses into safe compounds. and turn off the engine.

Information
A defective catalytic converter contributes to air
pollution and can impair your engine's
performance. A replacement unit must be an
original Honda part or equivalent.

111
 Specifications
■ Main Components Displacement 149.16 cm3 (9.099 cu-in)
Overall length 1,983 mm (78.1 in) Bore x stroke 57.300 x 57.843 mm (2.2559 x 2.2773 in)
Overall width 694 mm (27.3 in) Compression
11.3 : 1
Overall height 1,077 mm (42.4 in) ratio
Wheelbase 1,309 mm (51.5 in) Unleaded petrol
Fuel
Minimum ground clearance 166 mm (6.5 in) Recommended: 88 RON or higher
Caster angle 25° Fuel containing
ETHANOL up to 10 % by volume
Trail 91 mm (3.6 in) alcohol
CBR150R 135 kg (298 lb) Tank capacity 12 L (3.2 US gal, 2.6 Imp gal)
Curb weight GTZ6V or YTZ6V
CBR150RA 137 kg (302 lb) Battery
Maximum weight capacity *1 131 kg (289 lb) 12 V-5.0 Ah (10 HR)
Passenger capacity Rider and 1 passenger 1st 3.083
Specifications

Minimum turning radius 2.5 m (8.2 ft) 2nd 1.941

3rd 1.500
*1 : Including rider, passenger, all luggage, and accessories Gear ratio
4th 1.227
5th 1.041
6th 0.923
Reduction ratio
3.260 / 3.000
(primary / final)

112
 Specifications

■ Service Data Recommended

Honda DOT 3 or DOT 4 Brake Fluid
Front 100/80-17M/C 52P brake fluid
Tyre size
Rear 130/70-17M/C 62P Cooling system
0.58 L (0.61 US qt, 0.51 Imp qt)
Tyre type Bias-ply, tubeless capacity
Recommended Front IRC RX-01F Recommended
HONDA PRE-MIX COOLANT
tyre Rear IRC RX-01R coolant
Recommended
Tyre air pressure Front 175 kPa (1.75 kgf/cm2, 25 psi) Drive chain lubricant.
drive chain
(Driver only) Rear 200 kPa (2.00 kgf/cm2, 29 psi) If not available, use SAE 80 or 90 gear oil.
lubricant
Tyre air pressure Front 175 kPa (1.75 kgf/cm2, 25 psi)
Drive chain slack 25 - 35 mm (1.0 - 1.4 in)
(Driver and
Rear 225 kPa (2.25 kgf/cm2, 33 psi) Standard drive FSCM428H or KMC428HG
passenger)
chain No. of links 128
Minimum tread Front 1.5 mm (0.06 in)

Specifications
depth Drive
Rear 2.0 mm (0.08 in) 15T
Standard sprocket sprocket
MR9C-9N (NGK) or
Spark plug (standard) size Driven
U27EPR-N9 (DENSO) 45T
sprocket
Spark plug gap 0.8 - 0.9 mm (0.03 - 0.04 in)
Idle speed 1,600 ± 100 rpm
Honda 4-stroke motorcycle oil API Service
Classification SG or higher, excluding oils
Recommended
marked as “Energy Conserving” or “Resource
engine oil
Conserving,” SAE 10W-30, JASO T 903
standard MA
After
1.1 L (1.2 US qt, 1.0 Imp qt)
Engine oil draining
capacity After
1.3 L (1.4 US qt, 1.1 Imp qt)
disassembly

113
 Specifications

■ Bulbs
Headlight LED
Brakelight/Taillight LED
Front turn signal LED
Rear turn signal LED
Position light LED
License plate light LED

■ Fuses
Main fuse 20 A
CBR150R 10 A
Other fuse
CBR150RA 20 A, 10 A
Specifications

■ Torque Specifications
Seat lock cover bolt 4.2 N m (0.4 kgf m, 3.1 lbf ft)
Right middle cowl bolt B 4.2 N m (0.4 kgf m, 3.1 lbf ft)
Engine oil drain bolt 24 N m (2.4 kgf m, 18 lbf ft)
Rear axle nut 68 N m (6.9 kgf m, 50 lbf ft)
Front axle nut 59 N m (6.0 kgf m, 44 lbf ft)

114
 Index
A C
ABS (Anti-lock Brake System)......................... 8 Caring for Your Motorcycle ........................ 103
ABS (Anti-lock Brake System) Clip ...................................................................... 52
indicator .................................................... 20, 85 Clock ............................................................. 15, 19
Accessories ........................................................ 10 Clutch
Air Cleaner......................................................... 49 Freeplay................................................................ 75
Average Fuel Mileage ..................................... 17 Clutch System ................................................... 74
Coolant ................................................ 45, 64, 113
B Crankcase Breather ......................................... 78
Battery ................................................. 40, 51, 112 Crash ..................................................................... 5
Brakelight Switch............................................. 68 Current Fuel Mileage ...................................... 17
Brakelight/Taillight ......................................... 95
Brakes D

Index
Fluid....................................................... 44, 66, 113 Digital Clock Adjustment............................... 19
Pad Wear ............................................................. 67 Document Bag ......................................... 32, 102
Braking ................................................................. 7 Drive Chain ......................................... 44, 70, 113
Bulb
Brakelight/Taillight ............................................. 95 E
Front/Rear Turn Signal Light ........................... 95 Electrical Trouble ............................................. 93
Headlight.............................................................. 94 Emergency Stop Signal .................................. 29
License Plate Light ............................................. 96
Position Light ...................................................... 94

115
 Engine G
Number.............................................................. 109 Gasohol ............................................................ 110
Oil .......................................................... 43, 61, 113 Gear Position Indicator .................................. 15
Overheats............................................................. 84
Starting ................................................................. 26 H
Will Not Start....................................................... 83 Harness Band Clip ........................................... 55
Environment ................................................... 108 Headlight ........................................................... 94
Equipment Headlight Aim .................................................. 79
Owner’s Manual ........................................ 32, 102 Headlight Dimmer Switch ............................. 22
Tool Kit........................................................... 32, 50 Helmet Holder.................................................. 32
High Beam Indicator....................................... 21
F High Coolant Temperature Indicator ... 21, 84
Flooded Engine ................................................ 26 Horn Button ...................................................... 22
Index

Frame Number ............................................... 109

Front Seat .......................................................... 53 I
Front Suspension ............................................. 80 Ignition Cut-off System
Front/Rear Turn Signal Light ........................ 95 Banking Sensor................................................. 102
Fuel Ignition Key..................................................... 101
Gauge ................................................................... 15 Ignition Switch................................... 23, 26, 102
Recommended ................................................... 31
Remaining............................................................ 15
Tank Capacity ..................................................... 31
Fuels Containing Alcohol............................. 110
Fuses .................................................... 42, 97, 114
116
Indicator Front/Rear Turn Signal ..................................... 95
ABS (Anti-lock Brake System)................... 20, 85 License Plate........................................................ 96
Gear Position....................................................... 15 Position................................................................. 94
High Beam........................................................... 21 Load Limits................................................ 11, 112
High Coolant Temperature ...................... 21, 84 Loading Guidelines.......................................... 11
Left Turn Signal .................................................. 21
Neutral.................................................................. 21 M
PGM-FI (Programmed Fuel Injection) Maintenance
Malfunction ................................................ 20, 85 Fundamentals ..................................................... 38
Right Turn Signal................................................ 21 Importance .......................................................... 34
Warning................................................................ 85 Safety .................................................................... 34
Indicators........................................................... 20 Schedule............................................................... 35
Instruments ....................................................... 14 Maximum Weight Limit ................................. 11

Index
Instruments, Controls, ＆Other Modifications.................................................... 10
Features ......................................................... 102
N
K Neutral Indicator ............................................. 21
Keys................................................................... 101
O
L Odometer............................................ 16, 17, 102
License Plate Light........................................... 96 Oil
Light Engine................................................... 43, 61, 113
Brakelight/Taillight ............................................. 95 Overheating ...................................................... 84
Bulb ....................................................................... 93
117
 P Right Middle Cowl ............................................. 56
Parking ................................................................. 9 Repair Kit ........................................................... 87
Parts Location................................................... 12 Riding Precautions ............................................ 7
Passing Light Control Switch ........................ 22 Right Middle Cowl........................................... 56
Petrol .................................................................. 31
PGM-FI (Programmed Fuel Injection) S
Malfunction Indicator Lamp (MIL)...... 20, 85 Safety Guidelines ............................................... 3
Position Light.................................................... 94 Safety Precautions ............................................. 6
Protective Apparel............................................. 6 SEL Button ......................................................... 14
Serial Numbers............................................... 109
R SET Button......................................................... 14
Rear Seat............................................................ 58 Shifting Gears ................................................... 28
Rear Suspension............................................... 81 Shutter................................................................ 25
Index

Recommended Side Stand.......................................................... 69

Coolant........................................................ 45, 113 Spark Plugs........................................................ 59
Engine Oil ............................................ 43, 61, 113 Specifications.................................................. 112
Fuel............................................................... 31, 112 Speedometer .................................................... 15
Refuelling........................................................... 31 Start Button....................................................... 22
Removal Starting the Engine ......................................... 26
Battery................................................................... 51 Steering Lock .................................................... 24
Clip......................................................................... 52 Storage
Front Seat............................................................. 53 Equipment ........................................................... 32
Harness Band Clip.............................................. 55 Owner’s Manual ........................................ 32, 102
Rear Seat.............................................................. 58 Storing.............................................................. 106
118
Switch W
Brakelight ............................................................. 68 Warning Indicators On ................................... 85
Headlight Dimmer ............................................. 22 Washing ........................................................... 103
Ignition.................................................. 23, 26, 102 Weight Limit............................................. 11, 112
Passing Light Control ........................................ 22 Wheels
Turn Signal........................................................... 22 Front Removal .................................................... 88
Switches ............................................................. 22 Rear Removal...................................................... 90

T
Tachometer ....................................................... 14
Throttle............................................................... 77
Tool ..................................................................... 50
Tool Kit ............................................................... 32

Index
Transporting ................................................... 107
Tripmeter ............................................ 16, 17, 102
Troubleshooting .............................................. 82
Turn Signal Indicator ...................................... 21
Turn Signal Switch........................................... 22
Tyres
Air Pressure ......................................................... 46
Puncture............................................................... 87
Replacing....................................................... 46, 87

119