Analog and Interface Product Solutions

Temperature Sensor Design Guide

Temperature Measurement Solutions for Silicon IC Temperature
Sensor, Thermocouple, RTD and Thermistor-Based Applications

Design ideas in this guide use the following devices. A complete device list and corresponding data sheets for these products can be
found at: www.microchip.com

Voltage Output Logic Output Serial Output Comparators and

Temperature Sensors Temperature Sensors Temperature Sensors Operational Amplifiers PGA
MCP9700 TC620 TC6501 MCP9800 TC72 TC913A MCP6544 MCP6521
MCP9701 TC621 TC6502 MCP9801 TC74 TC7650 MCP6001 MCP6522
TC1046 TC622 TC6503 MCP9802 TC77 TC7652 MCP6021 MCP6524
TC1047A TC623 TC6504 MCP9803 TCN75 MCP616 MCP6231 MCP6528
TC624 MCP9805 MCP6541 MCP6271
MCP6542 MCP6281
MCP6543 MCP6291
Temperature Sensor Design Guide
TEMPERATURE SENSORS – OVERVIEW

In many systems, temperature control is fundamental. There Silicon Output Temperature Sensors
are a number of passive and active temperature sensors
that can be used to measure system temperature, including: Logic Output Temperature Sensors:
thermocouple, resistive temperature detector, thermistor Logic output temperature sensor families offer excellent
and silicon temperature sensors. These sensors provide temperature accuracy (±1°C, typical), with a very low operating
temperature feedback to the system controller to make current of less than 600 μA. These devices can replace
decisions such as, over-temperature shutdown, turn-on/off mechanical switches in a variety of sensing and control
cooling fan, temperature compensation or general purpose applications.
temperature monitor.
Voltage Output Temperature Sensors:
Microchip offers a broad portfolio of thermal management
Voltage output temperature sensors develop an output voltage
products, including Logic Output, Voltage Output and Serial
proportional to temperature, with a typical temperature
Output Temperature Sensors. These products allow the
coefficient of 6.25 mV/°C, 10 mV/°C and 19.5 mV/°C
system designer to implement the device that best meets their
respectively. These temperature-to-voltage converters can
application requirements. Key features include high accuracy,
sense a -40°C to +125°C temperature range and feature
low power, extended temperature range and small packages.
an offset voltage that allows reading negative temperatures
In addition, Microchip’s linear products can be used to support without requiring a negative supply voltage. The extremely
Thermocouple, RTD and Thermistor applications. low operating current minimizes self-heating and maximizes
Common Methods of Interfacing a Sensor battery life.
Serial Output Temperature Sensors:
Serial (digital) output temperature sensors offer excellent
Analog Output
Sensor Volts
temperature accuracy (±0.5°C, typical) with a very low
operating current of 250 μA (typical). Communication with
Serial Output
these devices is accomplished via an industry standard
SMBus, I2C™ or SPI compatible interface protocol. These
Logic Output OFF ON
RTD devices feature fast temperature conversion rate, with
Fan
temperature resolution for the entire family ranging from
C
VDD
0.0625°C to 0.5°C.
–
Thermocouple,
Thermistor/Amplifiers +
VOUT Thermocouples
Op Amps/Comparators
VDD MCP6541 Thermocouples are usually selected because of their wide
temperature range (as low as -270°C to as high as 1750°C),
R
R
R
ruggedness and price; however, they are highly non-linear and
often require significant linearization algorithms. In addition,
VREF the voltage output of this temperature sensing element is
Thermistor/
Amplifiers R
VDD relatively low when compared to devices that can convert
MCP6S21 voltage signals to a digital representation. Consequently,
Programmable +

Gain Amplifier
R
– VOUT
analog gain stages are required in the circuit.
RT C
(PGA)
Gain-Adjustment Resistive Temperature Detectors (RTDs)
Input Selection
RTDs are able to sense temperatures with extreme accuracy,
SPI™ have consistent and repeatable performance and low drift
error (-200°C to +850°C). For precision, these sensors also
require a linearization look-up table in the microcontroller due
Temperature Measurement Applications to sensor non-linearities.
Computing: Thermistors
– CPU overtemperature protection
– Fan control Thermistors (-100°C to +150°C) are normally used for
overtemperature shutdown purposes. Although not as
Cellular/PCS: accurate as some of the other temperature sensor solutions,
– Power amplifier temperature compensation thermistors are inexpensive and come in small packages. They
– Thermal sensing of display for contrast control are also non-linear and require a temperature compensation
Power Supply Embedded Systems: look-up table.
– Overtemperature shutdown
– Battery management

2
Temperature Sensor Design Guide
LOGIC OUTPUT TEMPERATURE SENSORS

Logic output sensors typically function as a thermostat, TC6501/2/3/4 Key Features:

notifying the system that a minimum or maximum temperature Factory-programmed Temperature Set Points
limit has been reached. Sometimes referred to as a
No External Components Required
temperature switch, these devices can be used to turn-on
either a fan or warning light when high temperature conditions Small SOT-23 Packages
are detected. Since the output is typically not latched, the TC620/1 Key Features:
switch will turn off when the temperature falls below the Dual Trip Point Temperature Sensor
temperature set point.
Wide Voltage Supply Range: +4.5V to +18V
Note that it is necessary to have hysteresis so the switch does
not “chatter” when crossing the temperature set point. User-programmable Trip Point and Hysteresis

Most logic output temperature sensors are available in either TC623 Key Features:
a Hot (for temperature-increasing applications) or Cold (for Dual Trip Point Temperature Sensor
temperature-decreasing applications) option. The hot and User-programmable Trip Point and Hysteresis
cold options ensure that the hysteresis is in the appropriate
position, either below or above the temperature set point.
TC622/4 Key Features:
Low-Cost Single Trip Point Temperature Sensor
Logic Output Temperature Sensor Key Features: Temperature Set Point Easily Programs with a Single
Logic-Level Output External Resistor
Notifies System When Temperature is Above (or Below) TO-220 Package for Direct Mounting to Heatsink
a Preset Value
Factory and User-programmable Temperature Settings
Available in a Variety of Output Configurations
Logic Output Temperature Sensor Applications:
Fan Controllers
Power Supplies
Motor Drives
RF Power Amplifiers

Logic Output Temperature Sensors Used as Temperature Switches

VDD +12V Overtemperature
VDD Indicator
VDD
NTC
12V DC
Thermistor
Brushless
Fan
THERM VDD VCC PIC®
RLOW TOVER VDD MCU
RSET
LOW SET HIGH LIMIT TC6501 Overtemperature OUT
RHIGH TSET
HIGH SET LOW LIMIT GND HYST LED OUT INT
System
TC622 GND Controller
GND CONTROL Logic-Level
TC621 MOSFET

TC6501 Hot and Cold Options

Voltage

Temperature

Voltage

Temperature

3
Temperature Sensor Design Guide
VOLTAGE OUTPUT TEMPERATURE SENSORS

A Voltage Output Temperature Sensor provides an analog TC1046 Key Features:

output signal of varying voltage on a single pin. The output Wide Temperature Measurement Range: -40°C to +125°C
voltage has a factory set slope (e.g., 10 mV/°C) and correlates
High Temperature Conversion Accuracy: ±0.5°C
to the ambient temperature of the device. The device output is
typically connected to a stand-alone or integrated ADC (Analog- Linear Temperature Slope: 6.25 mV/°C
to-Digital Converter). TC1047A Key Features:
The circuit shown below can be used to measure the LCD Wide Temperature Measurement Range: -40°C to +125°C
panel’s temperature at multiple locations. The operational High Temperature Conversion Accuracy: ±0.5°C
amplifier functions as an averaging circuit to provide a Linear Temperature Slope: 10 mV/°C
composite voltage output that can be used to adjust the LCD
contrast. MCP6021 (Op Amp) Key Features:
Single-Supply: 2.5V to 5.5V
Voltage Output Temperature Sensor Key Features:
Rail-to-Rail Input and Output
Easy System Integration
Unity-Gain Stable
Reduces PCB Space
VDD/2 Reference Output
Low Current Consumption
Minimizes Design Time
Voltage Output Temperature Sensor Typical Applications:
Cellular Phones
Temperature Measurement/Instrumentation
Consumer Electronics

LCD Contrast Control

LCD Module

VDD Upper-Left
Sensor R
TC1047A R
VDD
R
Lower-Right TC1047A VDD
Sensor –
LCD
Adj. Module
+ MCP6021

VDD
2

Using the TC1046 to Create a Simple Temperature Measurement System

7 8
VDD
6 9
RS U1
5 10
R/W
2 x 20 LCD 11 20
4
E RB4 21
3 Dot Matrix 12 C7
RB5
2 13 0.1 μF 1 22
VDD RB6 23
1 14
RB7 2 24
15 16 17 18 3 25
RS RB4
4 26
RA5 R/W RB5
5 27
E RB6
VDD 6 28
1 U2 Optional for RB7
C8 noisy applications RA5
7
0.1 μF PIC16F872A 11
2
R1 12
TC1046 4.7 kΩ 13
9 14 XTAL
3 15 32 kHz
C3 16
22 pF
10 17 C1 C2
18 15 pF 15 pF
8
19

4
Temperature Sensor Design Guide
VOLTAGE OUTPUT TEMPERATURE SENSORS

Linear Active Thermistors MCP9700/01 Typical Applications:

The MCP9700/01 Linear Active Thermistor™ Integrated Circuit Entertainment Systems
(IC) is an analog temperature sensor that converts temperature Home Appliance
to an analog voltage output. Battery Packs and Power Supplies for Portable Equipment
This sensor competes with a thermistor solution in price and General Purpose Temperature Monitoring
performance. Unlike resistive sensors (such as thermistors),
the Linear Active Thermistor IC does not require an additional Sensor Application Tips
signal-conditioning circuit. Therefore, the biasing circuit The MCP9700/01 is designed to drive large capacitive loads.
development overhead for thermistor solutions can be This capability makes the sensor immune to board parasitic
eliminated by implementing this low-cost device. The voltage capacitance, which allows the sensor to be remotely located
output pin (VOUT) can be directly connected to the ADC input of and drive long PCB trace or shielded cables to the ADC. In
a microcontroller. addition, adding capacitive load at VOUT helps the sensor
The sensor output voltage is proportional to ambient transient response by reducing overshoots or undershoots.
temperature with temperature coefficient of 10 mV/°C and This provides a more stable temperature reading.
19.5 mV/°C with output voltage at 0°C scaled to 500 mV and IC temperature sensors use analog circuitry to measure
400 mV, respectively. These coefficients are ideal for 8-bit temperature. Unlike digital circuits, analog circuits are more
Analog to Digital Converters referenced at 5V and 2.5V. The susceptible to power-supply noise. It is recommended that a
operating current is 6 μA (typ.) and use a PCB space saving bypass capacitor CBYPASS of 0.1 μf to 1 μf be placed at close
5-pin SC-70 package. proximity to the VDD and VSS pins of the sensor. The capacitor
provides protection against power-supply glitches by slowing
MCP9700/01 Key Features: fast transient noise. However, the effectiveness of the bypass
5-pin SC-70 Package capacitor depends upon the power-supply source resistance.
Operating temperature range: -40°C to 125°C Larger source resistance provides RC network with the CBYPASS
Temperature Coefficient: 10 mV/°C (MCP9700) and adds a corner frequency to filter out the power-supply
Temperature Coefficient: 19.5 mV/°C (MCP9701) noise. Adding a series resistor to the power-supply line is
adequate to increase the source resistance.
Low power: 6 μA (typ.)

Typical Application Circuit For a Thermistor Solution

+5V

R* VDD VOUT
MCP9700

VSS
CLOAD*
CBYPASS

*Optional

5
Temperature Sensor Design Guide
VOLTAGE OUTPUT TEMPERATURE SENSORS

IC Sensor Compensation Technique Graph 1: MCP9800 2nd Order Equation

Typically, the accuracy of an IC temperature sensors is within MCP9800
±1°C at room temperature and the accuracy error increases 3.0
exponentially at hot and cold temperature extremes. The
2.0
sensor error characteristic has a parabolic shape, which can Compensated Sensor Accuracy

Accuracy (°C)
be described using a second order equation. The equation 1.0
can be used to compensate the sensor error to provide higher
accuracy over the operating temperature range. This is done by 0.0
evaluating the equation at the temperature of interest (sensor
-1.0
output in degree Celsius) and subtracting the result from the
sensor output. The subtracted result in °C is the compensated Sensor Accuracy
-2.0
sensor output.
-3.0
For higher accuracy, the equation can be computed using
a standard PIC microcontroller, such as PIC16FXXXX, -55 -35 -15 5 25 45 65 85 105 125
PIC18FXXXX, PIC24FXXXX or dsPIC30FXXXX. Temperature (°C)

Compensated Sensor Output (°C) = Sensor Output (°C)

– Sensor Error|Sensor Output (°C) Graph 2: MCP9700 2nd Order Equation

A short look-up table can also be generated for low-level PIC MCP9700
3.0
microcontrollers such as PIC10FXX, PIC12FXXX, PIC14FXXX
and PIC16FXXX. For additional information, see AN1001: IC 2.0 Compensated Sensor Accuracy
Temperature Sensor Accuracy Compensation with a PICmicro®
Accuracy (°C)

Microcontroller. 1.0

Typical Results 0.0

Equation 1, 2 and 3 show the 2nd order error equation of -1.0
the tested parts for the MCP9800, MCP9700 and MCP9701,
respectively. Since these devices have functional differences, -2.0 Sensor Accuracy
the operating temperature range and temperature error
coefficients differ. The equations below describe the typical -3.0
device temperature error characteristics. -55 -35 -15 5 25 45 65 85 105 125
Temperature (°C)
Equation 1: MCP9800 2nd Order Equation

ErrorT_2 = EC2(125°C – TA) • (TA – -55°C) Graph 3: MCP9701 2nd Order Equation
+ EC1(TA – -55°C) + Error-55
MCP9701
Where: 3.0
EC2 = 150 x 10-6°C/°C2 2.0
EC1 = 7 x 10-3°C/°C Compensated Sensor Accuracy
Accuracy (°C)

Error-55 = -1.5°C 1.0

Equation 2: MCP9700 2nd Order Equation 0.0

ErrorT_2 = EC2(125°C – TA) • (TA – -40°C) -1.0

+ EC1(TA – -40°C) + Error-40 -2.0 Sensor Accuracy
Where:
-3.0
EC2 = 244 x 10-6°C/°C2
-15 5 25 45 65 85 105 125
EC1 = 2 x 10-12°C/°C » 0°C/°C
Temperature (°C)
Error-40 = -2°C

Equation 3: MCP9701 2nd Order Equation

ErrorT_2 = EC2(125°C – TA) • (TA – -515°C)

+ EC1(TA – -15°C) + Error-15
Where:
EC2 = 200 x 10-6°C/°C2
EC1 = 1 x 10-3°C/°C
Error-15 = -1.5°C

6
Temperature Sensor Design Guide
SERIAL OUTPUT TEMPERATURE SENSORS

Typically, serial output temperature sensors use a two or three MCP9800/1/2/3 Key Features:
wire interface to the host controller and provide functions ±1°C (max.) Accuracy From -10°C to +85°C
that are user programmable. Functions such as temperature
Supply Current: 200 μA (typ.)
alert output allow the user to configure the device as a stand-
alone temperature monitoring system. The alert output can be One Shot Temperature Measurement
used to notify the system controller to act upon the change in TC72 Key Features:
temperature. This feature eliminates the need for the system 10-Bit Temperature-to-Digital Converter
controller to monitor temperature continuously using the serial
interface. Power-saving One-shot Temperature Measurement
Low Power Consumption
The figure below illustrates a multi-zone temperature
measurement application. Communication with the MCP9801 TC74 Key Features:
is accomplished via a two-wire I2C™/SMbus compatible serial Simple 2-wire Serial Interface
bus. This device can be set to notify the host controller when Digital Temperature-sensing in SOT-23-5 or TO-22-5
the ambient temperature exceeds a user-specified set point. Packages
The microcontroller can monitor the temperature of each
Low Power Consumption
sensor on the serial bus by either reading the temperature
data register or functioning as a stand-alone thermostat. The TC77 Key Features:
temperature threshold trip point is programmed by writing to 13-Bit Temperature-to-Digital Converter
the set point register. The ALERT pin is an open-drain output Low Power Consumption
that can be connected to the microcontroller’s interrupt pin for
±1°C (max.) Accuracy From +25°C to +65°C
overtemperature interrupt.
SPI Compatible Communications Interface
Serial Output Temperature Sensor Applications:
TCN75 Key Features:
Personal Computers
Industry Standard SMBus/I2C™ Interface
Set-top Boxes
Programmable Trip Point and Hysteresis
Cellular Phones
Thermal Event Alarm Output Functions as Interrupt or
General Purpose Temperature Monitoring
Comparator/Thermostat Output

A Multi-zone Temperature Measurement System Using the Two-wire Serial Communication Port of the MCP9801

VDD

R R R

GP2/INT
SDA SDA SDA INT SDA INT
SCL INT SCL
® SCL SCL
PIC V+
V+
MCU MCP9801 MCP9801 MCP9801
A0 A0 A0
System A1 A1 A1
Controller A2 A2 A2

Sensor #0 Sensor #1 Sensor #7

Clock Control Address A0

MCP9801 A1
Generator Logic Decoder
A2

Counter/ Serial Bus DATA

ADC Accumulator Interface CLK

Data Registers Calibration Registers VDD

VDD Temperature Data Offset Correction

Temp. Set Point Gain Correction

Temp. Hysteresis Configuration Registers
Set Point Control
ALERT Comparator Manufacturer/Ver. ID

7
Temperature Sensor Design Guide
DIGITAL TEMPERATURE SENSOR

The MCP9805 digital temperature sensor is designed to Typical Application

meet the JEDEC standard JC42.4 for Mobile Platform Memory
Memory Module
Module Thermal Sensor. This device provides an accuracy of
±1°C (max.) from a temperature range of +75°C to +95°C
(active range) and ±2°C (max.) from +40°C to +125°C (monitor Memory

range) as defined in the JEDEC standard.

Temperature
MCP9805 Key Features: SPD* Sensor

Accuracy with 0.25°C/LSb Resolution:

– ±1°C (max.) from +75°C to +95°C EEPROM MCP9805

– ±2°C (max.) from +40°C to +125°C

– ±3°C (max.) from -20°C to +125°C
R
Operating Current: 200 μA (typ.)
Shutdown Current: 0.1 μA (typ.)
MCP9805 Applications: R
Dual In-line Memory Module (DIMM)
Personal Computers (PCs) and Servers
3.3 VDD _SPD SDA SCLK Event
Hard Disk Drives and Other PC Peripherals
* Serial Presence Detect
General Purpose Temperature Sensor

Register Structure Block Diagram Typical Performance Curves

Average Temperature Accuracy
Event Output Hysteresis
3.0
Continuous Conversion or Shutdown VDD = 3.3V-3.6V
Critical Boundary Trip Lock
2.0

Event Boundary Window Lock bit

Accuracy (°C)

1.0
Spec. Limits
Clear Event Output Interrupt

Event Output Status

0.0

Enable/Disable Event Output

-1.0
Critical Event Output only
Event Output Polarity, Active-High/Low -2.0
Band Ga p
Event Output Comparator/Interrupt Temperature
Sensor -3.0
-40 -20 0 20 40 60 80 100 120
Configuration Register Temperature (°C)
Temperature Register (T A ) ΔΣ ADC

Temperature Upper-B oundary (TUPPER)

Temperature Lower -Boundary (T LOWER)

Temperature Accuracy Histogram, TA = +95°C
70%
Critical Temperature Limit (TCRIT) TA = +95°C
60% VDD = 3.3V
Manufacturer Identification Register 120 samples
50%
Occurrences

Device Identification and Revision Register 40%

Device Capability Register 30%

20%
Measurement Resolution
10%
Measurement Range
0%
Measurement Accuracy
-1.00

-0.75

-0.50

-0.25

0.00

0.25

0.50

0.75

1.00

Temperature Event Output

Temperature Accuracy (°C)

Register Pointer SMBus/Standard I 2C™

Interface
Temperature Accuracy Histogram, TA = +75°C
70%
TA = +75°C
A0 A1 A2 Event VD D GND SDA SCLK 60% VDD = 3.3V
120 samples
50%
Occurrences

40%

30%

20%

10%

0%
-1.00

-0.75

-0.50

-0.25

0.00

0.25

0.50

0.75

1.00

Temperature Accuracy (°C)

8
Temperature Sensor Design Guide
THERMOCOUPLES

Thermocouples The TC913A auto-zeroed op amp is selected because of its

The thermocouple can quantify temperature as it relates to a low offset voltage of 15 μV (max.) and high Common Mode
reference temperature. This reference temperature is usually Rejection Ratio (CMRR) of 116 dB (typ.). Auto-zero and chopper
sensed using a Thermistor, RTD or Integrated Silicon Sensor. amplifiers are good thermocouple amplifiers due to their low
The wide temperature ranges of the thermocouple make it offset voltage and CMRR specifications.
appropriate for many hostile sensing environments. The cold junction compensation circuit is implemented with the
The thermocouple consists of two dissimilar metallic wires that TC1047A silicon IC temperature sensor located on the PCB.
are connected at two different junctions, one for temperature Thermocouple Key Features:
measurement and the other for reference. The temperature
Self-powered
difference between the two junctions is determined by
measuring the change in voltage across the dissimilar metals -270 to 1750°C
at the temperature measurement junction. Remote Sensing
The Instrument Society of America (ISA) defines a number Robust Sensor
of commercially available thermocouple types in terms of Thermocouple Applications:
performance. Type E, J, K and T are base-metal thermocouples Stoves
and can be used to measure temperatures from about -200°C
Engines
to 1000°C. Type S, R and B are noble-metal thermocouples
and can be used to measure temperatures from about -50°C to Thermopiles
2000°C. Silicon Sensors for Cold Junction Compensation:
The circuit shown below can be used for remote thermocouple TC1047A Analog Temperature Sensor
sensing applications. The thermocouple is connected to the MCP9800 12-bit Serial Output Temperature Sensor
circuitry via a shielded cable and EMI filters. The thermocouple
is tied to a positive and negative supply via large resistors so
that the circuit can detect a failed open-circuit thermocouple.

Thermocouple Amplifier Circuit

+V R

+V
R
R C
<< EMI Filter –
IN_1
<< + TC913A
EMI Filter
Thermocouple

R
R R C
<< ADC

+V –V -V

TC1047A IN_2
Cold Junction Compensation

9
Temperature Sensor Design Guide
RESISTIVE TEMPERATURE DETECTORS (RTDs)

RTDs RTD Key Features:

RTDs (Resistive Temperature Detectors) serve as the standard Extremely Accurate with Excellent Linearity
for precision temperature measurements due to their excellent Variety of Packages
repeatability and stability characteristics. RTDs provide the Wire-wound or Thin-film
designer with an absolute result that is fairly linear over
temperature. The RTD’s linear relationship between resistance RTD Applications:
and temperature simplifies the implementation of signal- Industrial Instrumentation
conditioning circuitry. Hot Wire Anemometers
Circuit A below is easy to modify for a desired temperature- Laboratory-quality Measurements
to-frequency range. It requires either precision, low-drift
Recommended Products:
components or a calibration step to achieve high accuracy.
Circuit B utilizes pull-up and pull-down resistors to excite TC913A/B – Auto-zero Op Amps
the RTD, employing the TC913A op amp to amplify the small TC7650/2 – Chopper-stabilized Op Amps
voltage changes that correspond to temperature. MCP616/7/8/9 – Micropower Bi-CMOS Op Amps
MCP6021/2/4 – 10 MHz Bandwidth Op Amps
MCP6041/2/3/4 – 600 nA, Rail-to-Rail Input/Output Op Amps
MCP6541/2/3/4 – Push-Pull Output Sub-Microamp
Comparators
MCP6S21/2/6/7 – Single-ended, Rail-to-Rail Input/
Output Low-gain Programmable Gain Amplifiers (PGAs)

RTD Temperature Measurement Circuits

RTD

C VDD
+
Circuit A MCP6541 VOUT
-
R
VDD
R R

Circuit B VREF

Connector R
R
R
EMI Filter -
RTD TC913A
EMI Filter +

Shielded R R R
Cable
PCB

10
Temperature Sensor Design Guide
THERMISTORS (THERMALLY SENSITIVE RESISTORS)

Thermistors are built with semiconductor materials and can The advantage of the PGA circuit (below) is illustrated by
have either a positive (PTC) or negative (NTC) temperature comparing the VOUT slope plots of the conventional circuit
coefficient. However, the NTC is typically used for temperature with the PGA circuit. The VOUT slope for the PGA circuit has a
sensing. minimum value of 30 mV for temperatures greater than 35°C,
Advantages of thermistors include a very high sensitivity to which means that only a 9-bit ADC is required. In contrast, a
changes in temperature (having a thermal response of up to voltage divider with a gain of 1 will require an 11-bit, or higher,
-100Ω/°C at 25°C), fast response time and low cost. The ADC to provide an equivalent temperature resolution. The
main drawback of thermistors is that the change in resistance resolution of a thermistor circuit is important in applications
with temperature is non-linear at temperatures below 0°C and such as overtemperature shutdown circuits.
greater than 70°C. Thermistor Key Features:
A conventional fixed gain thermistor amplifier circuit is shown Inexpensive
below. A simple voltage divider is created with a reference Two-wire Measurement
resistor (R1) and the thermistor (RT). A constant voltage source
Variety of Packages
is supplied (VREF) with the output of the voltage divider (VTH)
directly correlating to temperature. The response is shown in Thermistor Applications:
the graph of temperature vs. output voltage to the right of the Battery Chargers
circuit. It is fairly linear in the range of 0-70°C, but the accuracy Power Supplies
of the circuit is limited without adding additional circuitry.
Cold Junction Compensation

Conventional Fixed Gain Thermistor Amplifier

VREF
5.0
4.5 G = +1 V/V
R1 4.53K R2 VDD
100K 4.0
VTH 3.5
+
VOUT (V)

3.0
MCP6001 VOUT 2.5
- 2.0
RT = 10K 1.5
@ 25°C 1.0
C1 0.5
1F 0.0
-50 -25 0 25 50 75 100 125 150
Thermistor Temperature (°C)

PGA Circuit Interfaced with a Thermistor

VREF 5.0
RS VDD 4.5
R2
28K 4.0
G = +32

100K
G = +16

MCP6S21
G = +8

3.5
G = +4
G = +2
G = +1

+ VOUT
VOUT (V)

3.0
C1 – 2.5
RT = 10K
1F 2.0
@ 25°C
1.5
Gain Adjustment 1.0
Input Selection 0.5 Hysteresis
0.0
-50 -25 0 25 50 75 100 125 150
SPI Thermistor Temperature (°C)

11
Temperature Sensor Design Guide
RELATED SUPPORT MATERIAL

The following Application Notes are available on the Microchip Logic Output
web site: www.microchip.com.
AN762: Applications of the TC62X Solid-State Temperature
Application Notes Sensor
General Temperature Sensing Sensing temperature and comparing that temperature to preset
limits is the basis for a variety of problems that designers
AN679: Temperature Sensing Technologies face in system design and process control. This Application
The most popular temperature sensor technologies are Note discusses the new generation of small, easy-to-use,
discussed at a level of detail that will give the reader insight temperature-sensing products provided by Microchip; namely,
into the methods for determining which sensor is most the TC62X product family.
appropriate for a particular application.
AN773: Application Circuits of the TC620/TC621 Solid-State
AN867: Temperature-Sensing with a Programmable Gain Temperature Sensors
Amplifier Discusses the benefits of the TC620/TC621 solid-state
The implementation of temperature measurement systems temperature sensors.
from sensor to PIC® microcontroller using a NTC thermistor,
silicon temperature sensor, anti-aliasing filter, A/D converter Serial Output
and microcontroller are discussed.
AN871: Solving Thermal Measurement Problems Using the
AN929: Temperature Measurement Circuits for Embedded TC72 and TC77 Digital Silicon Temperature Sensors
Applications Discusses the benefits of the TC72/TC77 temperature sensors
Explores selection techniques for temperature sensor and by analyzing their internal circuitry, illustrating the principles
conditioning circuits to maximize the measurement accuracy, these sensors employ to accurately measure temperature.
while simplifying the interface to a microcontroller.
AN913: Interfacing the TC77 Thermal Sensor to a PICmicro®
AN1001: IC Temperature Sensor Accuracy Compensation with a Microcontroller
PICmicro® Microcontroller Discusses system integration, firmware implementation and
The typical accuracy of analog and serial-output IC temperature PCB layout techniques for using the TC77 in an embedded
sensors is within ±1°C, however, at hot or cold extremes, system.
the accuracy decreases non-linearly. This application note
AN940: Interfacing the TC72 SPI Digital Temperature Sensor
is based on the analog output MCP9700/9701 and serial
to a PICmicro® Microcontroller
output MCP9800 temperature sensors. It derives an equation
describing the sensor’s typical non-linear characteristics, which Techniques for integrating the TC72 into an embedded system
can be used to compensate for the sensor’s accuracy error are demonstrated using the PICkit™ Flash Starter Kit.
over the specified operating temperature range. TB050: Monitoring Multiple Temperature Nodes Using TC74
Thermal Sensors and a PIC16C505
Silicon IC Temperature Sensors
The PIC16C505 is a 14-pin MCU that can easily interface to
Analog Output the TC74. This Technical Brief illustrates the ease of interfacing
AN938: Interfacing a TC1047A Analog Output Temperature these two products.
Sensors to a PICmicro® Microcontroller TB052: Multi-Zone Temperature Monitoring with the TCN75
Discusses system integration, firmware implementation and Thermal Sensor
PCB layout techniques for using the TC1047A in an embedded Presents an example of a simple, multi-zone thermal-monitoring
system. system using the Hardware mode of the Master Synchronous
TB051: Precision Temperature Measurement Technical Brief Serial Port (MSSP) module of a PIC® microcontroller.

Provides a description for interfacing a TC1046 temperature

sensor to a PIC16F872 microcontroller. A 2 x 20 dot matrix
LCD is included in the design to provide additional functionality.

12
Temperature Sensor Design Guide
RELATED SUPPORT MATERIAL

Thermocouples Demonstration/Evaluation Kits

AN684: Single-Supply Temperature Sensing with For additional information on these and other analog
Thermocouples demonstration and evaluation kits, visit the Microchip web site
at: www.microchip.com/analogtools
This Application Note focuses on circuit solutions that use
thermocouples in their design. The signal-conditioning path for MCP9700 Temperature-to-Voltage Converter PICtail™
the thermocouple system is discussed, followed by complete Demonstration Board
application circuits. Part Number: MCP9700DM-PCTL

RTDs MCP9800 Temp Sensor PICtail™

Demonstration Board
AN687: Precision Temperature Sensing with RTD Circuits
Part Number: MCP9800DM-PCTL
Focuses on circuit solutions that use platinum RTDs in their
design.
AN895: Oscillator Circuits for RTD Temperature Sensors
MCP9800 Temperature Data Logger Demonstration Board
Demonstrates how to design a temperature sensor oscillator Part Number: MCP9800DM-DL
circuit using Microchip’s low-cost MCP6001 operational
amplifier and the MCP6541 comparator. TC72 Digital Temperature Sensor PICtail™
Demonstration Board
Thermistors Part Number: TC72DM-PICTL
AN685: Thermistors in Single-Supply Temperature Sensing
Systems
Focuses on circuit solutions that use Negative Temperature
TC74 Serial Digital Thermal Sensor Demonstration Board
Coefficient (NTC) thermistors in their design.
Part Number: TC74DEMO
AN897: Thermistor Temperature Sensing with MCP6S2X PGA
TC77 Thermal Sensor PICtail™ Demonstration Board
Presents two circuits that employ a precise, Negative Part Number: TC77DM-PICTL
Temperature Coefficient (NTC) thermistor for temperature
measurement. TC64X/64XB Fan Speed Controller Demonstration Board
Part Number: TC642DEMO
TC64X/64XB Fan Speed Controller Evaluation Board
Part Number: TC642EV
TC650 Fan Controller Demonstration Board
Part Number: TC650DEMO

TC652 Fan Controller Demonstration Board

Part Number: TC652DEMO
TC1047A Temperature-to-Voltage Converter PICtail™
Demonstration Board
Part Number: TC1047ADM-PICTL

13
 See Microchip’s Product Selector Guide for complete product selection and specifications.

14
Serial Output Temperature Sensor Products
Accuracy @ 25°C
Device Serial Communication Temperature Range (°C) VDD Min. (V) VDD Max (V) IQ Max. (μA) Packages Development Tools
(Typ./Max)
MCP9800DM-DL
MCP9800 I2C™ 0.5/1 -40 to +125 2.7 5.5 400 SOT-23-5
MCP9800DM-PCTL
MCP9801 I2C™ 0.5/1 -40 to +125 2.7 5.5 400 SOIC-8, MSOP-8
MCP9802 SMBus 0.5/1 -40 to +125 2.7 5.5 400 SOT-23-5
MCP9803 SMBus 0.5/1 -40 to +125 2.7 5.5 400 SOIC-8, MSOP-8
MCP9805 SMBus 2/3 (0.5/1 75°C-95°C) -40 to +125 3.0 3.6 500 TSSOP-8, DFN-8
TC74 SMBus/I2C 0.5/2 -40 to +125 2.7 5.5 350 SOT-23-5, TO-220-5 TC74DEMO
TCN75 SMBus/I2C 0.5/2 -40 to +125 2.7 5.5 1000 SOIC-8, MSOP-8
Temperature Sensor Design Guide

TC72 4-Wire SPI 0.5/1 -40 to +125 2.65 5.5 400 MSOP-8, DFN-8 TC72DM-PICTL
TC77 3-Wire SPI 0.5/1 -40 to +125 2.7 5.5 400 SOIC-8, SOT-23-5 TC77DM-PCTL
Analog (Voltage Output) Temperature Sensor Products
Accuracy @ 25°C Slope Offset Voltage
Device Temperature Range (°C) VDD Min. (V) VDD Max. (V) IQ Max. (μA) Packages Development Tools
SELECTED PRODUCT SPECIFICATIONS

(Typ./Max) (mV/°C) (Output @ 0°C)(mV)

MCP9700 1/4 -40 to +125 2.3 5.5 12 10 500 SC-70-5 MCP9700DM-PCTL
MCP9701 1/4 -40 to +125 3.1 5.5 12 19.5 400 SC-70-5
TC1046 0.5/2.0 -40 to +125 2.7 4.4 60 6.25 424 SOT-23-3
TC1047/A 0.5/2.0 -40 to +125 2.7 4.4 60 10 500 SOT-23-3 TC1047ADM-PCTL
Logic Output Temperature Sensor Products
Accuracy @ 25°C VDD Min. VDD Max IQ Max.
Device Temperature Range (°C) Temperature Set Points Packages Development Tools
(Typ./Max) (V) (V) (μA)
TC620 1/3 -40 to +125 User-selectable, set by external resistor 4.5 18 400 PDIP-8, SOIC-8
TC621 1/3 -40 to +125 User-selectable, set by external resistor 4.5 18 400 PDIP-8, SOIC-8
TC622 1/5 -40 to +125 User-selectable, set by external resistor 4.5 18 600 PDIP-8, SOIC-8, SOT-220-5
TC623 1/3 -40 to +125 User-selectable, set by external resistor 2.7 4.5 250 PDIP-8, SOIC-8
TC624 1/5 -40 to +125 User-selectable, set by external resistor 2.7 4.5 300 PDIP-8, SOIC-8
TC6501 0.5/4 -40 to +125 Factory programmed thresholds 2.7 5.5 40 SOT-23-5
TC6502 0.5/4 -40 to +125 Factory programmed thresholds 2.7 5.5 40 SOT-23-5
TC6503 0.5/4 -40 to +125 Factory programmed thresholds 2.7 5.5 40 SOT-23-5
TC6504 0.5/4 -40 to +125 Factory programmed thresholds 2.7 5.5 40 SOT-23-5
 Operational Amplifiers
IQ (Typ./Max) VOS Max. Temperature Range Operating
Device # per Package GBWP (kHz) Packages Development Tools
(μA) (mV) (°C) Voltage Range (V)
TC913A 2 1500 8500/1100 0.15 0 to +70 6.5 to 16 PDIP-8
TC7650 1 2000 2000/3500 0.05 0 to +70 4.5 to 16 PDIP-8, PDIP-14
TC7652 1 400 1000/3000 0.05 0 to +70 5 to 16 PDIP-8, PDIP-14
MCP601 1, 2, 4 2800 230/325 2 -40 to +125 2.7 to 5.5 TSSOP-14, PDIP-8, SOIC-8, SOT-23-5
MCP616 1, 2, 4 190 19/25 0.15 -40 to +85 2.3 to 5.5 PDIP-8, SOIC-8, MSOP-8
MCP6001 1, 2, 4 1000 100/170 7 -40 to +125 1.8 to 5.5 SOT-23-5, SC-70-5
MCP6041 1, 2, 4 14 0.6/1 3 -40 to +125 1.4 to 5.5 TSSOP-14, PDIP-8, SOIC-8, MSOP-8, SOT-23-5
MCP6141 1, 2, 4 100 0.6/1 3 -40 to +125 1.4 to 5.5 TSSOP-14, PDIP-8, SOIC-8, MSOP-8, SOT-23-5
Temperature Sensor Design Guide

MCP6231 1, 2, 4 300 20/30 7 -40 to +125 1.8 to 5.5 TSSOP-14, PDIP-8, SOIC-8, SOT-23-5, SC-70-5
MCP6271 1, 2, 4 2000 120/240 3 -40 to +125 2.0 to 5.5 TSSOP-14, PDIP-8, SOIC-8, MSOP-8, SOT-23-5
MCP6281 1, 2, 4 5000 450/570 3 -40 to +125 7.2 to 5.5 TSSOP-14, PDIP-8, SOIC-8, MSOP-8, SOT-23-5
MCP6291 1, 2, 4 10,000 1000/1300 3 -40 to +125 2.4 to 5.5 TSSOP-14, PDIP-8, SOIC-8, MSOP-8, SOT-23-5
SELECTED PRODUCT SPECIFICATIONS

Voltage Reference
Output Voltage Max Load Current Initial Accuracy Temperature Coefficient Max. Supply Current
Device VCC Range Packages Development Tools
(V) (mA) (%) (ppm/°C) (μA @ 25°C)
MCP1525 2.7 to 5.5 2.5 ±2 ±1 50 100 TO-92-3, SOT-23B-3
Comparators
# per Typical Propagation IQ Typical VOS Max
Device Operating Voltage (V) Temperature Range (°C) Packages Development Tools
Package Delay (μsec) (μA) (mV)
MCP6541 1 4 1 5 1.6 to 5.5 -40 to +85 PDIP-8, SOIC-8, MSOP-8, SOT-23-5
MCP6542 2 4 1 5 1.6 to 5.5 -40 to +85 PDIP-8, SOIC-8, MSOP-8
MCP6543 1 4 1 5 1.6 to 5.5 -40 to +85 PDIP-8, SOIC-8, MSOP-8
MCP6544 4 4 1 5 1.6 to 5.5 -40 to +85 PDIP-14, SOIC-14, TSSOP-14
Programmable Gain Amplifiers (PGAs)
Device Channels -3 db BW (MHz) IQ Typical (mA) VOS (μV) Operating Voltage (V) Temperature Range (°C) Packages Development Tools
MCP6S21 1 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 PDIP-8, SOIC-8, MSOP-8
MCP6S22 2 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 PDIP-8, SOIC-8, MSOP-8
MCP6S26 6 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 PDIP-14, SOIC-14, TSSOP-14
MCP6S28 8 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 PDIP-16, SOIC-16

15
Analog and Interface Products

Thermal Power
Management Management Linear Mixed-Signal Interface
Temperature LDO & Switching Op Amps A/D Converter CAN Peripherals
Sensors Regulators Families
Programmable Infrared
Fan Speed Charge Pump Gain Digital Peripherals
Controllers/ DC/DC Converters Amplifiers Potentiometers
Fan Fault LIN Transceiver
Detectors Power MOSFET Comparators D/A Converters
Drivers Serial Peripherals
Linear V/F and F/V
PWM Controllers Converters Ethernet Controller
Integrated
System Supervisors Devices Energy
Measurement
Voltage Detectors ICs
Voltage References

Battery
Management
Li-Ion/Li-Polymer
Battery Chargers
Smart Battery
Managers

Analog and Interface Attributes

Robustness Space Savings
MOSFET Drivers lead the industry in latch-up Resets and LDOs in SC70, A/D converters in a 5-lead
immunity/stability SOT-23 package
Low Power/Low Voltage CAN and IrDA® Standard protocol stack embedded in
Op Amp family with the lowest power for a given gain an 18-pin package
bandwidth Accuracy
600 nA/1.4V/14 kHz bandwidth Op Amps Low input offset voltages
1.8V charge pumps and comparators High gains
Lowest power 12-bit ADC in a SOT-23 package Innovation
Integration Low pin-count embedded IrDA Standard stack,
One of the first to market with integrated LDO with FanSense™ technology
Reset and Fan Controller with temperature sensor Select Mode™ operation
PGA integrates MUX, resistive ladder, gain switches, For more information, visit the Microchip web site at:
high-performance amplifier, SPI interface www.microchip.com

www.microchip.com
Microchip Technology Inc. • 2355 W. Chandler Blvd. • Chandler, AZ 85224-6199

Information subject to change. The Microchip name and logo, the Microchip logo, PIC and PICmicro are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
FanSense, Linear Active Thermistor, PICkit, PICtail and Select Mode are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are
property of their respective companies. © 2006, Microchip Technology Incorporated. All Rights Reserved. Printed in the U.S.A. 1/06 DS21895B

*DS21895B*