University

'0'Anusandhan Deemedto be
(YTER), Siksha
Faculty of Engineering and TechnologyJULY-2022
EXAMINATION,
END SEMESTER
CIRCUIT THEORY (EET2111)
Semester: 4TH
Time:3 Hours
Programme: B. Tech Mar
Full Marks: 60 *TaxO
Ques.
ks
Subject/Course Learning Outcome nomy
Nos.
Level 2
L2 1(a) 4
1(b), 2{c)
to analyze
CO1:Able to apply concept of phasordifferent L3
AC 1{c), 2(a)
fundamental lawS and theorems for L4 2
circuits. L6 2(b) 2
L2 3{b)
steady-state 3(a), 10(a,b,c)
CO2: Able to determine the L3
analysis of 1-phase and 3-phase circuits. L4 3(c) 6
L2
4{a,b), 5(a)
applications of 12
CO3: Able to understand the electrical L3 4{c), 5(b,c),
different
Laplace transform to analyze 6(a,b,c)
10
circuits. L3
8(b, c), 9(a,b,c)
magnetically coupled
CO4: Able to analyze
parameters of different two
circuit and determine 2
port networks. OP-AMP in a L6 8(a)
CO5: Able to design circuits using
applications.
number of practical L3 7(a)
function and 7(b) 2
Able to determine transfer LS
CO6: 7{c) 2
circuits. L6
design basic filter

(L1), Comprehension (L2), Application

levels: Knowledge
*Bloom's taxonomyEvaluation
(LA), (L5), Creation (L6)
(L3), Analysis mark.
question carries equal
Answer all questions. Each phase angle between the two 2
frequency and the
1. (ay Determine the (1000 t + 60°) Vand
voltages V(t) = 12 sin v..
= -6cos (1000t + 30°) V. Also find v, +
v2 (t) the
current in a 0.05 H inductor is I=42 ~30° A, If
The voltage across the
(b) determine the
frequency of the current is 60 FHz,
inductor in time domain.
circuit shown in Fig. 1, determine the value of the indot 2
In the source voltage V,
with the
such that the current is in phase
12 cos(1000t) V.
Page 1 of 4
2. (a) In the diagram in Fig, 2, v(t) = 50 cos(10t + 10) Vand 2
i(t) = 25 cos(10t + 40) A. Is the impedance of Box (as shown
in Fig. 2) inductive or capacitive? Justify your answer.
(b) Design a phase shifter circuit that will provide 45° leading phase 2
shift.
(C) Determine i(t) for the circuit shown in Fig. 3.

i() 10 2 1H
411

100 F
Bax 100 cos 10/V s0 v()

Fig. 1 Fig. 2 Fig. 3

3. (a) For the circuit shown in Fig. 4, find the value of Z so that 2
of
maximum power is transferred to it. Also find the value
maximum power.
- 10°) V and the 2
(b) The voltage across a load is v(t) = 60 cos (wt voltage drop is
the
current through the element in the direction of
i(t) = 1.5 cos(wt+50°) A
powers, (b) the real and reactive
Find: (a) the complex and apparent
load imnpedance.
powers, and (c)the power factor and the
in parallel with the load 2
Find the value of capacitor to be connected
0.95 leading, f=60 Hz.
in Fig. S tomake the source power factor
4 S2
50 KW
0.32
812 480/0 Vms lagging

-j6 2
Fig. S
Fig. 4 2
function.
4. (a) Find the Laplace Transform of the following
f(t).= t.e-sin(2t) u(t)
function.
(b) Find the Laplace Transform of the following
f(t) =cos (2t) u(t- 2) 2
signal shown in Fig.6
(c) Find the Laplace transform of the given
2
function.
S. (a) Find the inverse Laplace of the following

Page 2 of4
 3s + 1
F(S) =
(s + 4) 2
(b) Solve the given differential equation using Laplace Transform
dy + 4y = 10u(t), where y(0) = 1
dt
2
() Find the transfer function Yo(s) for the circuit shown in Fig. 7.
Vi(s)
()
22

F
12

1H

Fig. &
Fig. 6 Fig. 7 2
circuit shown in Fig.
6. (a) Determine i(t)using Laplace transform for the
8. Assume all initial condition zero. 2
5(s+1)
(b) Find f(t) at t-0and t-o, if FS) (s+2)(6+3)
2s 2
H(s) =
(c) The transfer function of a linear system is s+6

Find its impulse response.

bandpass filter (of the form of series RLC circuit) 2
7. (a) Design a passive and an upper cutoff
of 20.1 kHz
with a lower cutoff frequency kQ, Calculate L and C.
20.3 kHz. Take R 20
frequency of 2
a network is given by
(b) If the transfer function of 25
H(S) =s+1
justify the reason for the same. Also
Identify the type of filter and
find its cut-off frequency. frequency gain of 5 2
with a high
(c) Design an active high pass filter Use a 0.1 uF capacitor in your
frequency 2 kHz.
and a corner
design. following
an analog computer circuit to solve the
8.
(a} Design
equation, where y(0-0 Volt, and f) is any continuous
diferential
periodicsignal.
dy)42y()=f0)
dt

page 3 of 4
 2
two-port network as:
8 (b) Given the y-parameters of a
Y= ly]=-0.1 0.4
Calculate the corresponding T-parameters.
fashion have a total
(c) Two coils connected in series-aiding
inductance of 500 mH. When connected in of a series-opposing
mH. If the
configuration, the coils have a total inductance 300
find Li, L2
inductance of one coil (Li) is three times the other (L2),
and M. What is the coupling coefficient?
M
-j42
12 2 4S2
2S2 82
LË 252

Fig.10 Fig. 11
Fig. 9 2
ifL=4 H, Lg= SH
9. (a) For the coupled coils in Fig. 9, find the Leg,
and M=2H.
shown in Fig.10.
(b) Obtain the h parameter for the 2-Port network
2
Obtain the Z-parameter for the 2-Port network shown in Fig, 11.
(©)
positive phase-sequence three-phase voltage source connected in 2
10. (a) A of Vah = 20820° V rms.
a balanced wye has a line voltage
other line voltages.
Determine the phase voltages of the source and
One line voltage of a balanced Y-connected source is Vab = 2
(b) connected to a A-connected load
1202- 120° V. If the source is
line cuTents. Assume the abc
of 20240° N. Find the phase and
sequence.
2
three-phase motor can be regarded as a balanced Y-load. A three-
(c) A
motor draws 6 kW when the line voltage is 220 V and the
phase
apparent power and reactive
line current is 18 A. Determine the
the power factor of the motor.
power drawn by the motor. Also find

*End of Questions*

Page 4of 4