Valves and Valve Islands

Table of
Contents

Fig. Description Page Fig. Description Page

Small Valves 3-9 P- Supply and RPS-Manifolds 93-100
3/2 Way Valves, for Directional Valves, Series
manually-, mechanically -, S9-G1/8, S9-G1/4, S9-G1/2
pedal actuated
P-Supply Manifolds
Series K9-G1/8 Series PL-G1/8, G1/4, G1/2
Version for Panel Mounting RPS-Manifolds
to DIN 43696 Series PL-G1/8, G1/4
Flat Slide Valves 11-13 Special Valves 101-116
4/3 Way Valves, Series S9-G1/8, S9-G1/4
manually actuated
3/2,5/2, 5/3 Way Valves
Series DRS-G1/8 with NAMUR Connections
Series S9-G1/8, S9-G1/4
Compact Valves 15-42 5/2 Way Valves
in Threaded version for Two Hand Operation
with Push-in Connections 5/2 Way Oscillating Valves
Series S10-G1/8, G1/4 Series F-G1/4
3/2, 5/2, 5/3 Way Valves, 3/2 and 5/2 Way Valves with
pneumatic, electrically actuated pedal actuation
RPS Manifolds and Valve Islands, Series ARKV-G1/2 to G2
Accessories
2/2 Valve pneumatically actuated
Way Valves 43-79
Directional Valves 117-125
in Threaded version for Base Plate Mounting
Series S9-G1/8 to G1/2 Series S20
3/2, 5/2, 5/3 Way Valves, 5/2 and 5/3 Way Valves to
manually, pneumatically and VDMA 24563 Size 01
electrically actuated
5/2 and 5/3 Way Valves to
Version with Logic Elements
Version for Panel Mounting ISO 5599 Size 1, 2, 3
to DIN 43696 (only for series pneumatic, electrically actuated
S9-G1/8) Base Plates 127-134
Solenoid-Poppet Valves 81-86 Single Base Plates and
directly actuated Base Plate combinations to
Series EV-M5/G1/8 – VDMA 24563 Size 01
– ISO 5599 Size 1, 2, 3
3/2 Way Solenoid Poppet Valves
Screw-in Version
Series V9-G1/8
3/2 Way Solenoid Poppet Valves
with Threaded Ports
Way Valves to
Valve Islands * 87-92
ATEX-Directives 94/9/EG ATEX95)
Series IM-20, G1/8, G1/4
Version with Multipole You will find further information on the ATEX Directives
Connection in our brochure No A5P060E
* Neutral purchase order form
for valve islands see page 135

1
2
Table of Contents
Directional
Version Actuation
Characteristics
Page
Dimensions Order Instructions
Control Valves
Overview
Manual Control 4 5 9 Series K9-G1/8
3/2 Way Valves Mechanical 4 6 9
Pedal 4 6 9
for panel mounting to Manual Control 4 7, 8 9
DIN 43696

3
3/2 Characteristics – Series K9

Way Valves Characteristics

General Features
Symbol Unit Description

System Poppet Valve

Series K9
Mounting 2 Screws M4
G1/8
Tube connection Thread
Actuation: Port size G1/8
– Rotary lever, indexed Weight (mass) kg See page 4
– Rotary lever, spring return Installation In any position
– Rotary lever, indexed, Ambient temperature Tmin/max °C -10 to +55
secured in two positons range Note:
Please consult us for operating
– Pushbutton Medium temperature Tmin/max °C +5* to +60 temperatures below 0° C
– Cam operation range
Medium Filtered and lubricated or filtered and unlubricated
– Toggle cam operation
Lubrication None or oil mist lubrication
– Plunger operated
– Cam operated, free cam left Pneumatic Characteristics
or free cam right Nominal pressure pn bar 6
– Pivoted lever Operating pressure range pmin/max bar 0 – 10
– Pedal Nominal flow QN l/min 220
– Actuators for panel Flow direction 1 → 2 normally closed
mounting 3 → 2 normally open
Actuation
Versions:
For panel mounting, actuators Actuation Manual, mechanical and pedal actuated
correspond to internatio- (see page 5-8)
nally standardized mounting Stroke mm 1.5 – 3
dimensions to DIN 43696 Actuation force Fb N (see page 4)
(Ø22, Ø30 mm)
Non-overlapping poppet valve * -10°C when using dry compressed air
with low actuating force and
short response time. Actuation Forces, Rotation Angles and Weight
Applicable as normally closed
or normally open valve Description Type Actuation Rotation Weight
(see drawing). force (N) angle mass (kg)
Rotary lever, indexed K9 312-1/8 4.5 ±45°, 90° 0.110
Rotary lever,
K9 312RF-1/8 4.5 ±45°, 90° 0.110
spring return
Rotary lever, indexed K9 312S-1/8 4.5 ±45°, 90° 0.110
secured in both positions

Pushbutton K9 314RF-1/8 25 – 0.075

Cam operation K9 321RF-1/8 11 – 0.070
Toggle cam operation K9 324RF-1/8 5 ±40° 0.120
Plunger operated K9 323RF-1/8 32 – 0.050
Cam operated K9 325RF-1/8 5 ±40° 0.120
free cam left
Cam operated K9 326RF-1/8 5 ±40° 0.120
free cam right
Pivoted lever K9 329RF-1/8 2* ±40° 0.115
Pedal K9 331RF-1/8 12 – 0.800
Basic valve for panel K9 390RF-1/8 35 – 0.060
mounting actuators
* at a distance of 100 mm from fulcrum

4
Rotary Lever – Type: K9 312..-1/8 Plunger Operated – Type: K9 323RF-1/8

 
∅
   deep
2.7x8
Stroke min. 1.5 ∅

Stroke max. 3,0






∅






 








 








   







   




  

 

* = P when used as “normally closed“ * Self tapping screws CM 3x.. DIN 7500
** = P when used as “normally open“ to be used
** = P when used as “normally closed“
*** = P when used as “normally open“

Pushbutton – Type: K9 314RF-1/8 Cam operation– Type: K9 321RF-1/8


∅




Actuation stroke

















Actuation stroke 4,2






   







 


 


 




* = P when used as “normally closed“ * = P when used as “normally closed“

** = P when used as “normally open“ ** = P when used as “normally open“

Order Instructions see page 9, Characteristics see page 4

Dimensions in mm

5
Toggle Cam Operation – Type: K9 324RF-1/8 Pivoted Lever – Type: K9 329RF-1/8



 




∅

Actuation stroke





















 






   







   




 

 

* = P when used as “normally closed“ * = P when used as “normally closed“

** = P when used as “normally open“ ** = P when used as “normally open“

Cam Operated free cam left / right Pedal – Type: K9 331RF-1/8

Type: K9 325RF-1/8, K9 326RF-1/8

Actuation stroke
 






Actuation stroke




























 






  


 
 




* = P when used as “normally closed“ * = P when used as “normally closed“

** = P when used as “normally open“ ** = P when used as “normally open“

6
Basic Valve with adaptor for panel mounting Mounting holes for mounting diameters 22 and 30 mm
Type: K9 390RF-1/8
Mounting diameter ∅22 mm Mounting diameter ∅30 mm








 















 


   





* = P when used as “normally closed“

** = P when used as “normally open“

Rotary Lever, indexed – Type: 12T-22, 12T-30 Rotary Lever with spring return – Type: 12T-RF-22, 12T-RF-30

Mounting diameter ∅22 mm Mounting diameter ∅30 mm Mounting diameter ∅22 mm Mounting diameter ∅30 mm


 ∅

∅
∅ 
∅ 



























°

°

°
°


Order Instructions see page 9, Characteristics see page 4

Dimensions in mm

7
Pushbutton – Type: 13T-RF-22, 13T-RF-30 Rotary Switch – Type: 17T-22, 17T-30

Mounting diameter ∅22 mm Mounting diameter ∅30 mm Mounting diameter ∅22 mm Mounting diameter ∅30 mm

∅ ∅
∅
  ∅



























Mushroom Pushbutton – Type: 15T-RF-22, 15T-RF-30

Mounting diameter ∅22 mm Mounting diameter ∅30 mm

°

∅

°




















Locking Switch – Type: 16T-22, 16T-30 Mushroom Switch (EMERGENCY SHUTDOWN) –

Type: 18T-22, 18T-30
Mounting diameter ∅22 mm Mounting diameter ∅30 mm
∅ ∅ Mounting diameter ∅22 mm Mounting diameter ∅30 mm
 

∅ ∅

































Order Instructions see page 9, Characteristics see page 4

Dimensions in mm

8
Order Instructions – 3/2 Way Poppet Valves, Series K9
Actuation Symbol Mounting Order Instructions Page
Ø (mm) Type Order No.
2
Rotary lever, 12 K9 312-1/8 PA 10269 5
indexed
1 3
2
Rotary lever, 12 10 K9 312RF-1/8 PA 10270 5
spring return
1 3

Rotary lever, 12 2
K9 312S-1/8 PA 10349 5
indexed
secured in both positions 1 3
2
Pushbutton 12 10 K9 314RF-1/8 PA 10271 5

1 3
2
Cam operation 12 10 K9 321RF-1/8 PA 10272 5

1 3
2
Toggle cam operation 12 10 K9 324RF-1/8 PA 10273 6

1 3
2
Plunger operated 12 10 K9 323RF-1/8 PA 10235 5

1 3
2
Cam operated 12 10 K9 325RF-1/8 PA 10274 6
free cam left
1 3
2
Cam operated 12 10 K9 326RF-1/8 PA 10275 6
free cam right
1 3
2
Pivoted lever 12 10 K9 329RF-1/8 PA 10276 6

1 3
2
Pedal 12 10 K9 331RF-1/8 PA 10277 6

1 3
2
Panel mounting valve with 10 K9 390RF-1/8 PA 10278 7
adaptor for interchangeable
actuation 1 3

Rotary lever, 22 12T-22 KX 9355 7

indexed 30 12T-30 KX 9314

Rotary lever, 22 12T-RF-22 KX 9356 7

spring return 30 12T-RF-30 KX 9315

Pushbutton 22 13T-RF-22 KX 9357 8

30 13T-RF-30 KX 9316

Mushroom pushbutton 22 15T-RF-22 KX 9358 8

30 15T-RF-30 KX 9317

Locking switch 22 16T-22 KX 9359 8

30 16T-30 KX 9318

Rotary switch 22 17T-22 KX 9360 8

30 17T-30 KX 9319

Mushroom switch 22 18T-22 KX 9361 8

EMERGENCY SHUTDOWN 30 18T-30 KX 9320

9
10
Contents
Directional
Version Actuation
Characteristics
Page
Dimensions Order Instructions
Control Valves
Overview
Rotary lever 12 13 13 Series DRS-G1/8
4/3 Way Valves
Rotary switch 12 13 13

11
4/3 Way Characteristics – Series DRS
Characteristics Symbol Unit Description
Flat Slide General Features
Valves System Flat slide valve without automatic return to neutral
position
Mounting 2 Screws M4
Series DRS
Tube connection Thread
G1/8
Port size Port P, A, B: G1/8
Port R: M5
Actuation: Weight (mass) kg 0.500
– Rotary lever
– Rotary switch Installation In any position
Ambient temperature Tmin/max °C -10 to +55 Note:
range Please consult us for operating
temperatures below 0° C

Medium temperature Tmin/max °C -10 to +60

range
Medium Filtered compressed air
Lubrication Oil mist lubrication compatible with Buna N
Pneumatic Characteristics
Nominal pressure pn bar 6
Operating pressure range pmin/max bar 0 – 10
Nominal flow QN l/min 350
Actuation
Manual control Direct
Actuation force Fb N ca. 6

12
Rotary Lever – Type: DRS 412 .-1/8 Rotary Switch – Type: DRS 417 .-1/8

∅  









 








 


 



 Angle of rotation
   
 
 







Swivelling range

    

    










  


 
Angle of ro-  

 tation 

* After removing the cover and loosening the mounting screws,

Port identification: the rotary switch is infinitely variable.
A= 4 Outlet
B = 2 Outlet
R = 5 Exhaust
P = 1 Pressure supply

Order Instructions – 4/3 Way Flat Slide Valves, Series DRS

Actuation Symbol Order Instructions
Type Order No.
A B
Rotary lever a b DRS 412 B-1/8 PA 10267
Middle position pressurized
P R

Rotary lever a b
A B
DRS 412 E-1/8 PA 10266
Middle position vented
P R
A B
Rotary lever a b
DRS 412G-1/8 PA 10268
Middle position closed
P R
A B
Rotary switch a b
DRS 417 B-1/8 PA 10264
Middle position pressurized
P R
A B
Rotary switch a b
DRS 417 E-1/8 PA 10263
Middle position vented
P R
A B
Rotary switch a b
DRS 417 G-1/8 PA 10265
Middle position closed
P R

Dimensions in mm

13
14
Contents
Compact
Version Actuation Page
Characteristics Dimensions Order Instructions
Valves
Overview
2 x 3/2 Way Valves pneumatic 16,17 18, 20 29 With threaded
electric 16,17 19, 21 29 ports
5/2 Way Valves pneumatic 16,17 22, 23 30 Series S10..-1/8
electric 16,17 24, 25 30 Series S10..-1/4
5/3 Way Valves pneumatic 16,17 22, 23, 26, 31 or
27
electric 16,17 24, 25, 28 31 with push-in
Valve Manifold 16,17 32-35 30
connections
Assemblies Series S10..-Q6
Valve Islands 16,17 37, 38 36 Series S10..-Q8
RPS-Manifolds 40 40
Accessories 41, 42 41, 42

Overview
Description Actuation Port Versions
G1/8 G1/4 Standard with with Middle Position Functions
Q6 Q8 biased external middle posi- middle posi- middle positi-
position pilot air tion closed tion vented on pressurized
2x3/2 Way Valves pneumatic ■ ■ ■ – – ­– – –
normally closed permanent signal (1
normally open electric ■ ■ ■ – ■ ­– – –
permanent signal (1
5/2 Way Valves pneumatic ■ ■ ■ – – ­– – –
permanent signal (2
pneumatic ■ ■ ■ ■ – ­– – –
impulse
electric ■ ■ ■ – ■ ­– – –
permanent signal (2
electric ■ ■ ■ ■ ■ ­– – –
impulse
5/3 Way Valves pneumatic ■ ■ ■ – – ­■ ■ ■
permanent signal
electric ■ ■ ■ – ■ ­■ ■ ■
permanent signal
(1
Air spring return
(2
Return by either mechanical spring or air spring (see Order Instructions, page 29-31)
Note:
S10 Series valves are normally supplied without connector
– please include in Order Code or order separately (see Order Instructions)

15
Characteristics – Series S10..-1/8, S10..-1/4, S10..-Q6, S10..-Q8 (Single Valves) and IM10 (Valve Islands)
Characteristics Symbol Unit Description
Version with threaded ports with push-in connections (version Q6, Q8)

Actuation Pneumatic electrically pneumatic electrically pilot actuated

pilot actuated
General Features
System Spool Valve
Mounting 2 Screws M3 (S10..-1/8, S10..-Q6), 2 Screws M4 (S10..-1/4, S10..-Q8)
Tube connection Thread Threaded ports and push-in connections
Port size
– Series G1/8 Port 1, 3, 5: G1/8,
S10..-1/8, S10..-Q6 Port 2, 4: push-in connection OD 6 mm
– Series Port 1, 2, 4: G1/4 Port 1: G1/4 – Port 3, 5: G1/8
S10..-1/4, S10..-Q8 Port 3, 5: G1/8 Port 2, 4: push-in connection OD 8 mm
Nominal diameter mm 6
Weight (mass) kg See page 18, 20, 22, 26
Installation In any position
Ambient temperature range Tmin./max. °C -5 to +50 Note:
for use below freezing point please consult us
Medium temperature range Tmin./max. °C 0 to +50

Vibration restistance / G Max. 5

vibration
Impact strength/shock G Max. 30
Medium Filtered compressed air (5µm)
Lubrication With or without oil mist lubrication
(We recommend mineral oil type VG 32 to ISO 3448)
Pneumatic Characteristics
Nominal pressure pmin./max. bar 6
Operating pressure range
– permanent signal version pmin./max. bar ­2 – 8 (5/2 way version), 3 – 8 (5/3 and 2x3/2 way version)

– impulse version pmin./max. bar 1.5 – 8 (5/2 way version)

– with external pilot air pmin./max. bar -0.9 – 8 (5/2 way version), -0,9 ­– 8 (5/3 and 2x3/2 way version)

Nominal flow
Series QN l/min 5/2 way version 650, 5/3 way version 550, 2x3/2 way version 400
– S10..-1/8, S10..-Q6
Series QN l/min 5/2 way version 950, 5/3 way version 850, 2x3/2 way version 850
– S10..-1/4, S10..-Q8

16
Characteristics Symbol Unit Description
Actuation
Pneumatic Direct
– actuation pressure range
– permanent signal version pst min./max. bar ­2 – 8 (5/2 way version), 3 – 8 (5/3 and 2x3/2 way version)
– impulse version pst min./max. bar 1.5 – 8 (5/2 way version)
Electrical Electrically pilot actuated
single Valves S10
Voltage types Alternating current (50/60Hz) Direct current
Nominal voltage
– standard version Un V 230, 110, 48 ±10% 24, 12 ±10%
other voltages available on request
Power consumption, switching
– standard version VA (W) ca. 2.8 1.1
Power consumption, holding
– standard version VA (W) ca. 2 1.1
Duty cycle ED % 100
Electrical protection IP IP 65 to DIN 40050
(applise only to solenoid with plug)
Connection Connector to DIN EN 175301-803 form C (1
Electrical Electrically pilot actuated
valve islands IM10
Nominal voltage Un V 24, 12
Voltage types Direct current
Power consumption, switching VA (W) 1.1
Power consumption, holding VA (W) 1.1
Duty cycle ED % 100
Electrical protection IP IP 65 to DIN 40050
(Applise only to the electrically part in combination with sub-D connector,
IP 65)
Connection D-Sub connector 25pin
Switching indicator LED
Number of outputs max. 22, max. 18 (monostable)

(1 Solenoid also available with cable (length 1m) – see Order Instructions

17
2 x 3/2 Weight (mass) kg
Description Type Weight (mass)
Way Valves Pneumatic, by permanent signal S10 361R..-1/8 0.063 kg
Series S10 Electrical, by permanent signal S10 381R..-1/8 0.089 kg
Pneumatic, by permanent signal S10 361R..-Q6 0.070 kg
G1/8 Electrical, by permanent signal S10 381R..-Q6 0.097 kg
and
Push-In Connections 2 x 3/2 Way Valve, pneumatically actuated – threaded version
OD 6 mm Type: S10 361..-1/8 
  


Actuation systems:


– Pneumatic
– Electrical pilot actuated


  
Versions:
– 2x normally closed 
– 2x normally open
– 1x normally closed and


1x normally open
– With external pilot air


Accessories:


– Adapter plate for direct Ø2.6 – on rear side 
mounting on   M3 x 5 deep
HOERBIGER-ORIGA
profile-type cylinders 
– Mounting bracket  


For further information see

page 41, 42
(1
thread depth 7.5 mm


(2
thread depth 5 mm


 

2x 3/2 Way Valve, pneumatically actuated – version with push-in connection

Type: S10 361..-Q6 
  




  








Ø2.6 – on rear side 

  M3 x 5 deep


for tubing 





(1
thread depth 7.5 mm
(2
thread depth 5 mm


 

18
2 x 3/2 Way Valve, electrically actuated (permanent signal) – threaded version
Type: S10 381R..-1/8

  




  

  




 
 

Ø2.6 – on rear side




  M3 x 5 deep


Manual override   (only on version S)


(1
thread depth 7.5 mm


(2
thread depth 5 mm
  
Manual override

2 x 3/2 Way Valve, electrically actuated (permanent signal) – version with push-in connections
Type: S10 381R..-Q6

  




   

  







Ø2.6 – on rear side




  M3 x 5 deep


Manual override for tubing   (only on version S)



(1
thread depth 7.5 mm
(2
thread depth 5 mm


 
Manual override

For valve manifolds see page 32-34, for RPS manifolds see page 38, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

19
2 x 3/2 Weight (mass) kg
Description Type Gew. (mass)
Way Valves Pneumatic, by permanent signal S10 361R..-1/4 0.094 kg
Series S10 Electrical, by permanent signal S10 381R..-1/4 0.123 kg
Pneumatic, by permanent signal S10 361R..-Q8 0.116 kg
G1/4 Electrical, by permanent signal S10 381R..-Q8 0.147 kg
and Push-In
Connections 2 x 3/2 Way Valve, pneumatically actuated – threaded version
OD 8 mm Type: S10 361..-1/4
  

 (1
Actuation systems:
– Pneumatic






– Electrical pilot operated 



Versions:

– 2x normally closed
– 2x normally open 
– 1x normally closed and
1x normally open


– With external pilot air


Accessories:
– Adapter plate for direct


mounting on  – rear side 

M3 x 5 deep
Parker -ORIGA  
profile-type cylinders
– Mounting brackets 

  (2

For further information see



page 41, 42 (1
thread depth 7.5 mm 



(2
thread depth 5 mm


 

2 x 3/2 Way Valve, pneumatically actuated – version with push-in connections

Type: S10 361..-Q8
  

(1













 




 – rear side 

M3 x 5 deep
 



for tubing Ø8  (2





(1
thread depth 7.5 mm 


(2
thread depth 5 mm  

20
2 x 3/2 Way Valve, electrically actuated (permanent signal) – threaded version
Type: S10 381R..-1/4
  

 (1
















 – rear side M3 x 5 deep  to
DIN EN 175301-803
  form C



Manual override   (2 (only on version S)



(1
thread depth 7.5 mm






(2
thread depth 5 mm


 

Manual override

2 x 3/2 Way Valve, electrically actuated (permanent signal) – version with push-in connections

Type: S10 381R..-Q8   















 




 – rear side M3 x 5 deep  to

DIN EN 175301-803
  form C



for tubing Ø8  (2 (only on version S)

Manual override



for tubing








 

Manual override
(1
thread depth 7.5 mm
(2
thread depth 5 mm

For RPS manifolds see page Page 39, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

21
5/2 and 5/3 Weight (mass) kg
Description Type Weight (mass)
Way Valves Pneumatic, by permanent signal S10 561R..-1/8 0.063 kg
Series S10 Pneumatic, by impulse S10 561(562)-1/8 0.063 kg
Electrical, by permanent signal S10 581R..-1/8 0.076 kg
G1/8 and Electrical, by impulse S10 581(582)-1/8 0.089 kg
Push-In Connections Pneumatic, by permanent signal S10 561R..-Q6 0.070 kg
OD 6 mm Pneumatic, by impulse S10 561(562)-Q6 0.070 kg
Electrical, by permanent signal S10 581R..-Q6 0.083 kg
Actuation systems: Electrical, by impulse S10 581(582)-Q6 0.097 kg
– Pneumatic
– Electrical, pilot operated

Versions:
– With biased position 5/2 and 5/3 Way Valve, pneumatically actuated – threaded version
– With external pilot air Type: S10 561..-1/8, S10 562..-1/8, S10 561RF.-1/8

Accessories: 
– Adapter plate for direct   


mounting on
Parker -ORIGA


profile-type cylinders


– Mounting bracket
  
For further information see
page 41, 42  



Ø2.6 – rear side M3 x 5 deep 

 


 


(1
thread depth 7.5 mm


(2
thread depth 5 mm


 

22
5/2 and 5/3 Way Valve, pneumatically actuated – version with push-in connections
Type: S10 561..-Q6, S10 562..-Q6, S10 561RF.-Q6


  




  








Ø2.6 – rear side M3 x 5 deep 
 


for tubing 



(1
thread depth 7.5 mm
(2
thread depth 5 mm



 

For valve manifolds see page 32-34, for RPS manifolds see page 38, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

23
5/2 Way Valve, electrically actuated (permanent signal) – threaded version
Type: S10 581..-1/8

  




  

 



 


Ø2.6 – rear side M3 x 5 deep 
 


Manual override   (only on version S)

thread depth 7.5 mm 

(1



(2
thread depth 5 mm  

5/2 Way Valve, electrically actuated (permanent signal) – version with push-in connections
Type: S10 581..-Q6


  




  

 





 

Ø2.6 – M3 x 5 deep 
 


Manual override for tubing   (only on version S)


(1
thread depth 7.5 mm



(2
thread depth 5 mm  

For valve manifolds see page 32-34, for RPS manifolds see page 38, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

24
5/2 Way Valve, electrically actuated (impulse) – threaded version, Type: S10 581-1/8, S10 582-1/8
5/3 Way Valve, electrically actuated (permanent signal) – threaded version, Type: S10 581RF.-1/8

  




  

  




 
 

Ø2.6 – on rear side 

  M3 x 5 deep


Manual override   (only on version S)


(1
thread depth 7.5 mm


(2
thread depth 5 mm


 
Manual override

5/2 Way Valve, electrically actuated (impulse) – version with push-in connections, Type: S10 581-Q6, S10 582-Q6
5/3 Way Valve, electrically actuated (permanent signal) – version with push-in connections, Type: S10 581RF.-Q6

  




   

  







Ø2.6 – on rear side




  M3 x 5 deep


Manual override for tubing   (only on version S)


(1
thread depth 7.5 mm


(2
thread depth 5 mm


 
Manual override

For valve manifolds see page 32, 34, for RPS manifolds see page 38, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

25
5/2 and 5/3 Weight (mass) kg
Description Type Weight (mass)
Way Valves Pneumatic, by permanent signal
Pneumatic, by impulse
S10 561R..-1/4
S10 561(562)-1/4
0.097 kg
0.097 kg

Series S10 Electrical, by permanent signal

Electrical, by impulse
S10 581R..-1/4
S10 581(582)-1/4
0.110 kg
0.125 kg
Pneumatic, by permanent signal S10 561R..-Q8 0.118 kg
Pneumatic, by impulse S10 561(562)-Q8 0.118 kg
G1/4 and Electrical, by permanent signal S10 581R..-Q8 0.132 kg
Push-In Connections Electrical, by impulse S10 581(582)-Q8 0.147 kg
OD 8 mm
5/2 and 5/3 Way Valve, pneumatically actuated, threaded version
Type: S10 561..-1/4, S10 562..-1/4, S10 561RF.-1/4
Actuation systems:
  
– Pneumatic
– Electrical pilot actuated  (1



Versions: 



– With biased position


– With external pilot air 

Accessories:
– Adapter plate for direct 
mounting on
Parker Origa


profile-type cylinders
– Mounting bracket




 – on rear side 

For further information see M3 x 5 deep
page 41, 42  



  (2


(1
thread depth 7.5 mm 
thread depth 5 mm


(2



 

5/2 and 5/3 Way Valve, pneumatically actuated, version with push-in connections
Type: S10 561..-Q8, S10 562..-Q8, S10 561RF.-Q8
  

(1













 




 – on rear side 

M3 x 5 deep
 



for tubing Ø8  (2


(1
thread depth 7.5 mm 


(2
thread depth 5 mm 


 

26
5/2 Way Valve, electrically actuated (permanent signal) – threaded version
Type: S10 581..-1/4
  

 (1
















 – on rear side M3 x 5 deep to
 DIN EN 175301-803
form C
 



Manual override   (2 (only on version S)


(1
thread depth 7.5 mm 



(2
thread depth 5 mm 


 

5/2 Way Valve, electrically actuated (permanent signal) – version with push-in connections
Type: S10 581..-Q8
  

 (1













 




 – on rear side M3 x 5 deep  to

DIN EN 175301-803
  form C


Manual override
for tubing Ø8  (2 (only on version S)








(1
thread depth 7.5 mm


 
(2
thread depth 5 mm

For RPS manifolds see page 39, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

27
5/2 Way Valve, electrically actuated (impulse) – threaded version Type: S10 581-1/4, S10 582-1/4
5/3 Way Valve, electrically actuated (permanent signal) – threaded version Type: S10 581RF.-1/4
  

 (1
















 – on rear side M3 x 5 deep to 
DIN EN 175301-803

form C




Manual override   (2 (only on version S)

 
(1
thread depth 7.5 mm




 
(2
thread depth 5 mm


 

Manual override

5/2 Way Valve, electrically actuated (impulse) – version with Push-In Connections Type: S10 581-Q6, S10 582-Q8
5/3 Way Valve, electrically actuated (permanent signal) – version with Push-In Connections Type: S10 581RF.-Q8

  















 




 – on rear side M3 x 5 deep  to

DIN EN 175301-803
  form C



for tubing Ø8  (2 (only on version S)

Manual override



for tubing





(1
thread depth 7.5 mm 
(2
thread depth 5 mm


 

Manual override

For RPS manifolds see page 39, for mounting bracket see page 41,
for adapter plate see page 41
Dimensions in mm

28
Order Instructions – 2 x 3/2 Way Valves, Series S10..-1/8, S10..-1/4, S10..-Q6, S10..-Q8
Actuation System Symbol Connections Order Instructions Page
Thread Push-In Type Order No.
Pneumatic G1/8 – S10 361R2G-1/8 PA 10417 18
by permanent signal   – ODØ 6mm S10 361R2G-Q6 PA 10447 18
 
G1/4 – S10 361R2G-1/4 PA 10537 22
– ODØ 8mm S10 361R2G-Q8 PA 10567 23
   G1/8 – S10 361R2O-1/8 PA 10418 18
  – ODØ 6mm S10 361R2O-Q6 PA 10448 18
 
G1/4 – S10 361R2O-1/4 PA 10538 22
– ODØ 8mm S10 361R2O-Q8 PA 10568 23
  
G1/8 – S10 361RGO-1/8 PA 10419 20
  – ODØ 6mm S10 361RGO-Q6 PA 10449 18
 
G1/4 – S10 361RGO-1/4 PA 10539 22
– ODØ 8mm S10 361RGO-Q8 PA 10569 23
Electrical   
G1/8 – S10 381R2G-1/8-33- PA 10404-33- 19
by permanent signal   – ODØ 6mm S10 381R2G-Q6-33- PA 10434-33- 19
  G1/4 – S10 381R2G-1/4-33- PA 10524-33- 21
– ODØ 8mm S10 381R2G-Q8-33- PA 10554-33- 21
  
G1/8 – S10 381R2O-1/8-33- PA 10406-33- 19
  – ODØ 6mm S10 381R2O-Q6-33- PA 10436-33- 19
 
G1/4 – S10 381R2O-1/4-33- PA 10526-33- 21
– ODØ 6mm S10 381R2O-Q8-33- PA 10556-33- 21
  
G1/8 – S10 381RGO-1/8-33- PA 10408-33- 19
  – ODØ 6mm S10 381RGO-Q6-33- PA 10438-33- 19
 
G1/4 – S10 381RGO-1/4-33- PA 10528-33- 21
– ODØ 8mm S10 381RGO-Q8-33- PA 10558-33- 21
Electrical   
G1/8 – S10 381S-R2G-1/8-33- PA 10405-33- 19
by permanent signal   – ODØ 6mm S10 381S-R2G-Q6-33- PA 10435-33- 19
with external pilot air   G1/4 – S10 381S-R2G-1/4-33- PA 10525-33- 21
– ODØ 8mm S10 381S-R2G-Q8-33- PA 10555-33- 21
    
G1/8 – S10 381S-R2O-1/8-33- PA 10407-33- 19
  – ODØ 6mm S10 381S-R2O-Q6-33- PA 10437-33- 19
  G1/4 – S10 381S-R2O-1/4-33- PA 10527-33- 21
– ODØ 8mm S10 381S-R2O-Q8-33- PA 10557-33- 21
    
G1/8 – S10 381S-RGO-1/8-33- PA 10409-33- 19
  – ODØ 6mm S10 381S-RGO-Q6-33- PA 10439-33- 19
 
G1/4 – S10 381S-RGO-1/4-33- PA 10529-33- 21
– ODØ 6mm S10 381S-RGO-Q8-33- PA 10559-33- 21
    

Solenoid version/ Notes on ordering:

voltage All electrically actuated valves are supplied without connector
– for connector as standard.
00 without solenoid – please include this in Order No. or order it separately Variants
01 12 V DC (see Order Instructions). connector
02 24 V DC 00 without connector *
04 48 V DC For electrically actuated valves please complete the Type 88 standard connector
07 110 V DC Designation and Order No. with the order codes. ­ 15mm
50 12 V AC 89 230 V AC with LED
51 24 V AC Example:
3/2 Way Valve, threaded version G1/8, electrically actuated, and protective circuit
55 48 V AC 92 24 V DC with LED
57 110 V AC with spring return, normally closed, voltage 12 V DC, with standard
connector and protective circuit
61 230 V AC * Standard version
– with cable (length 1m)
41 12 V DC Order Instructions:
42 24 V DC S10 381R2G-1/8-0133-88 PA 10404-0133-88
71 12 V AC
72 24 V AC
Other voltages available on
request

29
Order Instructions – 5/2 Way Valves, Series S10..-1/8, S10..-1/4, S10..-Q6, S10..-Q8
Actuation System Symbol Connections Order Instructions Page
Thread Push-In Type Order No.
Connections
Pneumatic  
G1/8 – S10 561RF-1/8 PA 10410 22, 23
by permanent signal  
– ODØ 6mm S10 561RF-Q6 PA 10440 22, 23
G1/4 – S10 561RF-1/4 PA 10530 26

– ODØ 8mm S10 561RF-Q8 PA 10560 26
  G1/8 – S10 561R-1/8 PA 10411 22, 23
  – ODØ 6mm S10 561R-Q6 PA 10441 22, 23
G1/4 – S10 561R-1/4 PA 10531 26
 
– ODØ 8mm S10 561R-Q8 PA 10561 26
Pneumatic by impulse  
G1/8 – S10 561-1/8 PA 10412 22, 23
  – ODØ 6mm S10 561-Q6 PA 10442 22, 23
G1/4 – S10 561-1/4 PA 10532 26

– ODØ 8mm S10 561-Q8 PA 10562 26
– with biased position G1/8 – S10 562-1/8 PA 10413 22, 23
 
  – ODØ 6mm S10 562-Q6 PA 10443 22, 23

G1/4 – S10 562-1/4 PA 10533 26
– ODØ 8mm S10 562-Q4 PA 10563 26
Electrical 4 2
G1/8 – S10 581RF-1/8-33- PA 10390-33- 24
by permanent signal 14 12
– ODØ 6mm S10 581RF-Q6-33- PA 10420-33- 24
5 13
G1/4 – S10 581RF-1/4-33- PA 10510-33- 27
– ODØ 8mm S10 581RF-Q8-33- PA 10540-33- 27
  G1/8 – S10 581R-1/8-33- PA 10392-33- 24


– ODØ 6mm S10 581R-Q6-33- PA 10422-33- 24
G1/4 – S10 581R-1/4-33- PA 10512-33- 27

– ODØ 8mm S10 581R-Q8-33- PA 10542-33- 27
Electrical  
G1/8 – S10 581S-RF-1/8-33- PA 10391-33- 24
by permanent signal  
– ODØ 6mm S10 581S-RF-Q6-33- PA 10421-33- 24
with external pilot air G1/4 – S10 581S-RF-1/4-33- PA 10511-33- 27
 
– ODØ 8mm S10 581S-RF-Q8-33- PA 10541-33- 27
  G1/8 – S10 581S-R-1/8-33- PA 10393-33- 24
 
– ODØ 6mm S10 581S-R-Q6-33- PA 10423-33- 24

G1/4 – S10 581S-R-1/4-33- PA 10513-33- 27

– ODØ 8mm S10 581S-R-Q8-33- PA 10543-33- 27
Electrical by impulse 4 2
G1/8 – S10 581-1/8-33- PA 10394-33- 25
14 12
– ODØ 6mm S10 581-Q6-33- PA 10424-33- 25
G1/4 – S10 581-1/4-33- PA 10514-33- 27
513
– ODØ 8mm S10 581-Q8-33- PA 10544-33- 27
– with biased position G1/8 – S10 582-1/8-33- PA 10396-33- 25
 
  – ODØ 6mm S10 582-Q6-33- PA 10426-33- 25
G1/4 – S10 582-1/4-33- PA 10516-33- 27

– ODØ 8mm S10 582-Q8-33- PA 10546-33- 27
Electrical by impulse  
G1/8 – S10 581S-1/8-33- PA 10395-33- 25
with external pilot air  
– ODØ 6mm S10 581S-Q6-33- PA 10425-33- 25
   
G1/4 – S10 581S-1/4-33- PA 10515-33- 27
– ODØ 8mm S10 581S-Q8-33- PA 10545-33- 27
– with biased position G1/8 – S10 582S-1/8-33- PA 10397-33- 25
 
 
– ODØ 6mm S10 582S-Q6-33- PA 10427-33- 25
  
G1/4 – S10 582S-1/4-33- PA 10517-33- 27
– ODØ 8mm S10 582S-Q8-33- PA 10547-33- 27

Supplements on types and order no. see page 29

Notes on ordering: Example:

All electrically actuated valves are supplied without connector 5/2 Way Valve, Push-In Connections, electrically actuated,
as standard. with spring return, voltage 24 V DC, with standard connector.
– please include this in Order No. or order it separately
(see Order Instructions). Order Instructions:
For electrically actuated valves please complete the Type S10 581RF-Q6-0233-88 PA 10420-0233-88
Designation and Order No. with the order codes.

30
Order Instructions – 5/3 Way Valves, Series S10..-1/8, S10..-1/4, S10..-Q6, S10..-Q8
Actuation System Symbol Connections Order Instructions Page
Thread Push-In Type Order No.

Pneumatic  
G1/8 – S10 561RFG-1/8 PA 10414 23
permanent signal   – ODØ 6mm S10 561RFG-Q6 PA 10444 23

G1/4 – S10 561RFG-1/4 PA 10534 26
– ODØ 8mm S10 561RFG-Q8 PA 10564 26
 
G1/8 – S10 561RFE-1/8 PA 10415 23
  – ODØ 6mm S10 561RFE-Q6 PA 10445 23

G1/4 – S10 561RFE-1/4 PA 10535 26
– ODØ 8mm S10 561RFE-Q8 PA 10565 26
  G1/8 – S10 561RFB-1/8 PA 10416 23
  – ODØ 6mm S10 561RFB-Q6 PA 10446 23
 
G1/4 – S10 561RFB-1/4 PA 10536 26
– ODØ 8mm S10 561RFB-Q8 PA 10566 26
Electrical  
G1/8 – S10 581RFG-1/8-33- PA 10398-33- 25
permanent signal   – ODØ 6mm S10 581RFG-Q6-33- PA 10428-33- 25

G1/4 – S10 581RFG-1/4-33- PA 10518-33- 28
– ODØ 8mm S10 581RFG-Q8-33- PA 10548-33- 28
  G1/8 – S10 581RFE-1/8-33- PA 10400-33- 25
  – ODØ 6mm S10 581RFE-Q6-33- PA 10430-33- 25

G1/4 – S10 581RFE-1/4-33- PA 10520-33- 28
– ODØ 8mm S10 581RFE-Q8-33- PA 10550-33- 28
 
G1/8 – S10 581RFB-1/8-33- PA 10402-33- 25
  – ODØ 6mm S10 581RFB-Q6-33- PA 10432-33- 25
G1/4 – S10 581RFB-1/4-33- PA 10522-33- 28

– ODØ 8mm S10 581RFB-Q8-33- PA 10552-33- 28
Electrical   G1/8 – S10 581S-RFG-1/8-33- PA 10399-33- 25
permanent signal  
– ODØ 6mm S10 581S-RFG-Q6-33- PA 10429-33- 25
with external pilot air G1/4 – S10 581S-RFG-1/4-33- PA 10519-33- 28
 

– ODØ 8mm S10 581S-RFG-Q8-33- PA 10549-33- 28
 
G1/8 – S10 581S-RFE-1/8-33- PA 10401-33- 25
 
– ODØ 6mm S10 581S-RFE-Q6-33- PA 10431-33- 25
  
G1/4 – S10 581S-RFE-1/4-33- PA 10521-33- 28
– ODØ 8mm S10 581S-RFE-Q8-33- PA 10551-33- 28
 
G1/8 – S10 581S-RFB-1/8-33- PA 10403-33- 25
 
– ODØ 6mm S10 581S-RFB-Q6-33- PA 10433-33- 25
  
G1/4 – S10 581S-RFB-1/4-33- PA 10523-33- 28
– ODØ 8mm S10 581S-RFB-Q8-33- PA 10553-33- 28

Solenoid version/ Notes on ordering:

all electrically actuated valves are supplied without connector Variants
voltage
as standard connector
– for connector
– please include this in Order No. or order it separately 00 without connector *
00 without solenoid
01 12 V DC (see Order Instructions). 88 standard connector
02 24 V DC 15mm
04 48 V DC For electrically actuated valves please complete the Type 89 230 V AC with LED
07 110 V DC Designation and Order No. with the order codes. and protective circuit
50 12 V AC 92 24 V DC with LED
51 24 V AC Example: and protective circuit
55 48 V AC 5/3 Way Valve, middle position closed, Push-In Connections, * Standard version
57 110 V AC electrically actuated, with spring return, voltage 230V AC, without
61 230 V AC connector.
– with cable (length 1m)
41 12 V DC Order Instructions:
42 24 V DC S10 581RFG-Q6-6133-00 PA 10428-6133-00
71 12 V AC
72 24 V AC
Other voltages available on
request

31
Valve Manifold Valve Manifold assembly, fully assembled – threaded version, Type: S10-1/8-..

Assemblies
Series S10



  


G1/8







fully assembled

Actuation systems: 
– Pneumatic
– Electrical pilot actuated 

 


 



 

Drawing shows:
6-fold valve manifold S10-1/8-06, 24VDC
 Order No. PA10385-06-0233-00
 Valve positions: JJMM33

Dimension Table (mm)

Dimension Number of valves
2 4 6 8 10 12 14 16
A 52 84 116 148 180 212 244 276
B 42 74 106 138 170 202 234 266

For single valves see page 18-28, for order instructions see page 36

Dimensions in mm

32
Valve Manifold assembly, fully assembled – version with Push-In Connections, Type: S10-Q6-..
Valve Manifold
Assembly
Series S10



   Push-In Connections



OD 6 mm





 fully assembled

Actuation systems:
 – Pneumatic
– Electrical pilot actuated
 

 



 
Drawing shows:
6-fold valve manifold S10-Q6-06, 24VDC
Order No. PA10386-06-0233-00

Valve positions: JJMM33


Dimension Table (mm)

Dimension Number of valves
2 4 6 8 10 12 14 16
A 52 84 116 148 180 212 244 276
B 42 74 106 138 170 202 234 266

For single valves see page 18-28, for order instructions see page 36

Dimensions in mm

33
Order Instructions – Valve Manifold Assemblies
Order No. Valve positions

+
Solenoid version

Connector

Flow divider at
valve position
Number of
Valve positions 1-16

voltage
valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PA – – 33–
02 04 06 08 10 12 14 16
Version
PA 10385 Valves with
threaded
ports G1/8
Series:
S10-1/8
PA 10386 Valves with Only even numbers of Flow divider
push-in ports valves are possible! (for dualpressure operating)
OD 6 none (standard)
Series: Please enter the codes for the
valve types required. .. at valve position
S10-Q6

Number of Valves
02 1 – 2 valves
04 3 – 4 valves
06 5 – 6 valves
08 7 – 8 valves Order Codes Order Codes
10 9 – 10 valves for Valves and Cover Plates for Valves and Cover Plates
12 11 – 12 valves Code Description Page Code Description Page
14 13 – 14 valves A Cover plate for unused valve position 41 Electrically actuated
16 15 – 16 valves P Intermediate air supply adapter G1/8 41 K 2x 3/2 Way Valve NC, air spring return 19, 21
Pneumatically actuated N 2x 3/2 Way Valve NO, air spring return 19, 21
Solenoid version/ 8 2x 3/2 Way Valve NC, air spring return 18, 22 H 2x 3/2 Way Valve NC, NO, air spring return 19, 21
voltage 9 2x 3/2 Way Valve NO, air spring return 18, 22 M 5/2 Way Valve, spring return 24, 27
– for connector 0 2x 3/2 Way Valve NC, NO, air spring return 18, 22 L 5/2 Way Valve, air spring return 24, 27
00 without solenoid 1 5/2 Way Valve, spring return 22, 23, J 5/2 Way Valve, impulse 24, 27
01 12 V DC 26, 27 D 5/2 Way Valve, impulse, with biased position 24, 27
02 24 V DC 2 5/2 Way Valve, air spring return 22, 23, G 5/3 Way Valve, middle position closed, 25, 28
04 48 V DC 26, 27 spring return to middle position
07 110 V DC 3 5/2 Way Valve, impulse 22, 23, E 5/3 Way Valve, middle position exhausted, 25, 28
50 12 V AC 26, 27 spring return to middle position
51 24 V AC 4 5/2 Way Valve, impulse, with biased position 22, 23, B 5/3 Way Valve, middle position pressurized, 25, 28
55 48 V AC 26, 27 spring return to middle position
57 110 V AC 5 5/3 Way Valve, middle position closed, 22, 23,
61 230 V AC spring return to middle position 26, 27
– with cable (length 1m) 7 5/3 Way Valve, middle position exhausted, 22, 23, Order Codes
41 12 V DC spring return to middle position 26, 27 for Valves and Cover Plates
42 24 V DC 6 5/3 Way Valve, middle position pressurized, 22, 23, Code Description Page
71 12 V AC spring return to middle position 26, 27 Electrically actuated, with external pilot air
72 24 V AC X 2x 3/2 Way Valve NC, air spring return 19, 21
Other solenoid versions Y 2x 3/2 Way Valve NO, air spring return 19, 21
(voltages) available on request Z 2x 3/2 Way Valve NC, NO, air spring return 19, 21
F 5/2 Way Valve, spring return 24, 27
Connector R 5/2 Way Valve, air spring return 24, 27
Version S 5/2 Way Valve, impulse 24, 27
T 5/2 Way Valve, impulse, with biased position 24, 27
00 without connector U 5/3 Way Valve, middle position closed, 25, 28
(standard version) spring return to middle position
88 standard connector W 5/3 Way Valve, middle position exhausted, 25, 28
15 mm wide spring return to middle position
89 230 V AC with LED and V 5/3 Way Valve, middle position pressurized, 25, 28
protective circuit spring return to middle position
92 24 V DC with LED and
protective circuit

34
Valve Islands, fully assembled – threaded version, Type: IM10-1/8-..
Valve Islands
Series IM10
D-Sub multipole connector 25pole
G1/8

fully assembled








  
Actuation systems:




– Electrical pilot actuated




 Version:
Multipole version with
D-Sub multipole connector
25pole.

Valve positions:
– Combination mono-/


bistable


outputs





max. 22
 

max. 18 (monostable)





On request:
Expandable with external
field bus components
  Drawing shows: (Profi Bus DP, Inter Bus S,
 6fold valve manifold IM10-1/8-06, 24VDC CAN Device net, AS-Interface
 Order No. PA10490-06-22
Valve positions: JJMMMC

Dimension Table (mm)

Dimen- Number of valves
sion 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A 78 94 110 126 142 158 174 190 206 222 238 254 270 286 302 318 334
B 68 84 100 116 132 148 164 180 196 212 228 244 260 276 292 308 324

For single valves see page 18-28, for order instructions see page 39

Dimensions in mm

35
Valve Islands Valve Islands, fully assembled – with Push-In Connections, Type: IM10-Q6-..

Series IM10
Push-In Connections
OD 6 mm





fully assembled




  



Actuation systems:
– Electrical pilot actuated 




Version:
Multipole version with
D-Sub multipole connector
25pole.

Valve positions:


– Combination mono-/



bistabil



 

Outputs





max. 22
max. 18 (monostable)

On request:
Expandable with external
field bus components   Drawing shows:
(Profi Bus DP, Inter Bus S,  6fold Valve Islands IM10-Q6-06, 24VDC
CAN Device net, AS-Interface)  Order No. PA10491-06-22
Valve positions: JJMMMC

Dimension Table (mm)

Dimen- Number of valves
sion 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A 78 94 110 126 142 158 174 190 206 222 238 254 270 286 302 318 334
B 68 84 100 116 132 148 164 180 196 212 228 244 260 276 292 308 324

For single valves see page 18-28, for order instructions see page 36

Dimensions in mm

36
Order Instructions – Valve Islands
Order No. Valve positions

Solenoid version

Flow divider to
Number of
Valve positions 1-16

voltage
valves

valve
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
PA – –
02 04 06 08 10 12 14 16 18
Version
PA 10490 Valve Islands
with threaded
ports G1/8 Even and uneven numbers of Flow divider
Series: valves are possible! (for dualpressure operating)
IM10-1/8 without (standard)
Please enter the codes for the
PA 10491 Valve Islands valve types required. .. at valve position
with push-in
connections
OD 6, Series:
IM10-Q6
Order Codes
for Valves and Cover Plates
Valves Code Description Page
02 2 valves A Cover plate for unused valve position 41
03 3 valves * C Cover plate (monostable)* 41
04 4 valves O Cover plate (bistabil)* 41
05 5 valves P Intermediate air supply adapter G1/8 41
* including electrical socket

18 18 Valves
* uneven number of valve Order Codes
positions on request for Valves and Cover Plates
Code Description Page
Electrically actuated
Solenoid version/ K 2x 3/2 Way Valve NC, air spring return 19
voltage N 2x 3/2 Way Valve NO, air spring return 19
21 12 V DC H 2x 3/2 Way Valve NC, NO, air spring return 19
22 24 V DC M 5/2 Way Valve, spring return 24
L 5/2 Way Valve, air spring return 24
J 5/2 Way Valve, impulse 24
D 5/2 Way Valve, impulse, with biased position 25
G 5/3 Way Valve, middle position closed, 25
spring return to middle position
E 5/3 Way Valve, middle position exhausted, 25
spring return to middle position
B 5/3 Way Valve, middle position pressurized, 25
spring return to middle position

Order Codes
for Valves and Cover Plates
Code Description Page
Electrically actuated, with external pilot air
X 2x 3/2 Way Valve NC, air spring return 19
Y 2x 3/2 Way Valve NO, air spring return 19
Z 2x 3/2 Way Valve NC, NO, air spring return 19
F 5/2 Way Valve, spring return 24
R 5/2 Way Valve, air spring return 24
S 5/2 Way Valve, impulse 24
T 5/2 Way Valve, impulse, with biased position 25
U 5/3 Way Valve, middle position closed, 25
spring return to middle position
W 5/3 Way Valve, middle position exhausted, 25
spring return to middle position
V 5/3 Way Valve, middle position pressurized, 25
spring return to middle position

37
RPS-Manifolds Dimension Table (mm) – Type: RPSL-S10-1/8-..


for Directional Valves
      
­– Series S10-1/8 

– Series S10-Q6

 





RPS manifolds reduce and
simplify the tubing layout.
They provide a space-saving,
clear and simple, compact 
solution.





RPS manifolds have a com-
mon compressed air supply
port (P) and common exhaust 
ports (R, S).
From 2 to 16 valves can be
mounted on them.
(Other sizes available on re-
 
quest)

Materials:
RPS manifold Drawing shows: 4fold valve manifold
– aluminium
Screws Dimension Table (mm)
– galvanized steel Type Number of valves Dimension
Gasket
– oil-resistant rubber A B
RPSL-S10-1/8-02 02 52 42
RPSL-S10-1/8-04 04 84 74
RPSL-S10-1/8-06 06 116 106
RPSL-S10-1/8-08 08 148 138
RPSL-S10-1/8-10 10 180 170
RPSL-S10-1/8-12 12 212 202
RPSL-S10-1/8-14 14 244 234
RPSL-S10-1/8-16 16 276 266

Order Instructions and Weight

Order Instructions * consisting of Weight
Type Order No. Manifold Screws Seals (mass) [kg]
RPSL-S10-1/8-02 PD47254-0002 1 4 2 0.116
RPSL-S10-1/8-04 PD47254-0004 1 8 4 0.190
RPSL-S10-1/8-06 PD47254-0006 1 12 6 0.264
RPSL-S10-1/8-08 PD47254-0008 1 16 8 0.337
RPSL-S10-1/8-10 PD47254-0010 1 20 10 0.410
RPSL-S10-1/8-12 PD47254-0012 1 24 12 0.484
RPSL-S10-1/8-14 PD47254-0014 1 28 14 0.557
RPSL-S10-1/8-16 PD47254-0016 1 32 16 0.630
*other versions on request

For single valves see page 18-28, for order instructions see page 36

Dimensions in mm

38
Dimension Table (mm) – Type: RPSL-S10-1/4-..

RPS Manifolds
 

 for Directional Valves


­– Series S10-1/4
– Series S10-Q8





RPS manifolds reduce and
simplify the tubing layout.
They provide a space-saving,
clear and simple, compact


 solution.




RPS manifolds have a com-
mon compressed air supply
port (P) and common exhaust
 ports (R, S).
From 2 to 16 valves can be
mounted on them.
(Other sizes available on re-
  
quest)

Materials:
Drawing shows: 3fold manifold RPS manifold
– aluminium
Maßtabelle (mm) Screws
Type Number Dimension – galvanized steel
of valves Gasket
A B – oil-resistant rubber
RPSL-S10-1/4-02 02 59 49
RPSL-S10-1/4-04 04 97 87
RPSL-S10-1/4-06 06 135 125
RPSL-S10-1/4-08 08 173 163
RPSL-S10-1/4-10 10 211 201
RPSL-S10-1/4-12 12 249 239
RPSL-S10-1/4-14 14 287 277
RPSL-S10-1/4-16 16 325 315

Order Instructions and Weight

Order Instructions * consisting of Weight
Type Order No. Manifold Screws Seals (mass) [kg]
RPSL-S10-1/4-02 PD49210-0002 1 4 2 0.255
RPSL-S10-1/4-04 PD49210-0004 1 8 4 0.424
RPSL-S10-1/4-06 PD49210-0006 1 12 6 0.594
RPSL-S10-1/4-08 PD49210-0008 1 16 8 0.736
RPSL-S10-1/4-10 PD49210-0010 1 20 10 0.932
RPSL-S10-1/4-12 PD49210-0012 1 24 12 1.101
RPSL-S10-1/4-14 PD49210-0014 1 28 14 1.270
RPSL-S10-1/4-16 PD49210-0016 1 32 16 1.439
*other versions on request

For single valves see page 18-28

Dimensions in mm

39
Accessories Flow Divider Cover Plate
for unused Valve
Intermediate
Air Supply Adapter
for Valve Manifold Positions
Assemblies

Material: Aluminium Material: Aluminium Material: Aluminium

Order No. Order No. Order No.

– S10-1/8 (Q6): PD47353 – S10-1/8 (Q6): KL9114 – S10-1/8 (Q6): KL9115
– S10-1/4 (Q8): PD49322 – S10-1/4 (Q8): KL9186 – S10-1/4 (Q8): KL9187

Clamp Mounting for Order Instructions – Clamp Mounting for S10-1/8 (Q6)
DIN Rail Clamp Mounting Order No.
35 mm Number of valves for valve manifolds for valve islands
Type: S10-1/8 Type: IM10-1/8
2 PD47393-0002 PD47949-0002
4 PD47393-0004 PD47949-0004
6 PD47393-0006 PD47949-0006
8 PD47393-0008 PD47949-0008
10 PD47393-0010 PD47949-0010
11 – 18 on request PD48270
Versions:
– for Valve Manifolds S10
– for Valve Islands IM10 Order Instructions – Clamp Mounting for S10-1/4 (Q8)
Clamp Mounting Order No.
Material: Aluminium valves for RPS-manifold
Type: RPSL-S10-1/4-..
The delivery includes:
1 clamp mounting 2 PD49423-0002
4 screws 4 PD49423-0004
6 PD49423-0006
8 PD49423-0008
10 PD49423-0010
12-16 on request

Cable with
D-Sub multipole Order Instructions – Cable
connector 25pole Cable length Electrical protection Order No.
2m IP40 KL3355
5m IP40 KL3356
5m IP65 KL3357

Dimensions in mm

40
Dimension Table – Mounting Bracket for Single Valves Mounting Bracket for Accessories
Mounting Screws Single Valves
 DIN ISO 4762 - M3 x 6 Series S10 for Single Valves












 


 
Material: Steel, passivated

Order No.: KL9112

Dimension Table – Adapter Plate for Single Valves S10-1/8 (Q6) Adapter Plate
 for Single Valves
Series S10-1/8 (Q6)
Series S10-1/4 (Q8)


 








 Adapter plate for direct

  mounting on
Parker Origa
profile cylinders
Dimension Table – Adapter Plate for Single Valves S10-1/4 (Q8) Material: Aluminium

Order No.
– S10-1/8 (Q6): PD47420
– S10-1/4 (Q8): PD49325




 









 



Dimensions in mm

41
Accessories Connectors
for Series S10
Dimension Table – Connector

for Single Valves

­ 
 


 




– Standard version
– version with LED
Gasket
Material: Plastic

Versions and Order Instructions

Version Voltage Colour Order No.
Standard version 230 V AC/DC black KL9052
Bipolar LED and VDR 230 V AC transparent KL9056
to protect supply and 24 V DC transparent KL9118
switch

Dimensions in mm

42
Contents Directional
Version Actuation Page
System Characteristics Dimension Table Order Control Valves
Instructions
Overview
Series
3/2 Way Valves Manual Control 44-47 48-55 70-72
Series S9-G1/8, G1/4, pneumatic S9-G1/8 to G1/2
G1/2 electric

for panel mounting Manual Control

to DIN 43696 (G1/8)
5/2 Way Valves Manual Control 44-47 56-63 73-74
Series S9-G1/8, G1/4, pneumatic
G1/2 electric

for panel mounting Manual Control

to DIN 43696 (G1/8)
5/3 Way Valves Manual Control 44-47 64-69 75-77
Series S9-G1/8, G1/4, pneumatic
G1/2 electric
3/2 , 5/2 and Pneumatic 44-47 78-79 79
5/3 Way Valve AND
combinations OR
with Logic Elements TIMER
Series S9-G1/8, G1/4

43
3/2, 5/2 Series S9 – G1/8 to G1/2
Characteristics Symbol Unit Series S9
and 5/3 G1/8

Directional Actuation Manual control pneumatic electrical

Control Valves General Features

Type Spool valve
Series Mounting 2 Screws M5
S9-G1/8 to G1/2 Tube connection Thread
Thread G1/8 – 7.4 deep
Weight kg See page 48, 56, 64
Installation In any position
Ambient temperature range (1 Tmin. / max. °C -10 to +60 *

Medium temperature range (1 Tmin. / max. °C -10 to +60 *

Medium Filtered compressed air
* Valve Manifold Assemblies Lubrication With or without oil mist lubrication
with electrically actuated (We recommend the use of mineral oil type VG 32 to ISO 3448)
valves -10 to +50°C Pneumatische Characteristics
(1 Note: Nominal pressure pmin. / max. bar 6
For use below freezing point Operating pressure range pmin. / max. bar 0–10 (10 – –
please contact us – permanent signal version pmin. / max. bar – 0–10 2–10
(2 Actuation force for valves – impulse version pmin. / max. bar – 0–10 2–10
without spring return,
actuation with rotary lever: – with external pilot air pmin. / max. bar – – 0–10
5N Nominal flow QN l/min 500 (450 bei 3/2 Way Valve)
(3 Actuation force for valves Actuation
with spring return,
Manual control Direct
Actuation with rotary lever:
15N Stroke mm 4.5
(4 Only for version with biased Actuation force Fb N 7 (2
position 2 – 10 bar, 10 (3
pneumatically actuated Actuation force for See page 48
2 – 10 bar, electrically panel mounting actuators
actuated 2.5 – 10 bar
(5 Version with biased position Pneumatic Direct
2.5 – 10 bar Actuation pressure range
(6 Low wattage version: – permanent signal version pmin. / max. bar – 2–10 2–10
Plug to
– impulse version pmin. / max. bar – 1.5–10 1.5–10
DIN EN 175301-803
form A Electrical Electrical pilot operated
(7 Version “middle position Voltage type Alternating current (50/60Hz)
vented“ 1000 l/min Nominal voltage
(8 Version “middle position
vented“ 3300 l/min – Standard version Un V 230 ±10%
Version “middle position – Low wattage version Un V 230 ±10%
pressured“ 3600 l/min Initial power consumption G1/8 G1/4 G1/2
(9 5/3 Way Valve 2.5 – 10 bar – Standard version VA (W) 8.5 8.5 11.0
(10Valves with panel mounting
actuators 2 – 10 bar – Low wattage version VA (W) 6.6 6.6 7.8
Continuous consumption G1/8 G1/4 G1/2
– Standard version VA (W) 6.0 6.0 8.5
– Low wattage version VA (W) 3.9 4.9 4.9
Duty cycle ED % 100
Electrical protection IP IP65 to DIN 40050 (applise only to solenoid with plug)
Connection Plug to DIN EN 175301-803 form B – industrial standard (6

44
 Series S9 Series S9
G1/4 G1/2
Manual control pneumatic electrical Manual control pneumatic electrical

Spool valve Spool valve

2 Screws M6 2 Screws M6
Thread Thread
G1/4 – 11 deep G1/2 – 16 deep
See page 52, 60, 66 See page 54, 62, 68
In any position In any position
-10 to +60 * -10 to +60 *

-10 to +60 * -10 to +60 *

6 6
0–10 – – 0–10 – –
– 0–10 2–10 – 0–10 2.2–10
– 0–10 2–10 – 0–10 2.2–10
– – 0–10 – – 0–10
1300(7 3500(8

Direct Direct
6.5 9.4
10 (2 15 (2
15 (3 40 (3
– –

Direct Direct

2–10 2–10 2–10 – 2.2–10(9 2.2–10

1.5–10 1.5–10(4 1.5–10(4 – 1.5–10(5 1.5–10(4

Direct current

24 ±10% Other voltages on request

24 ±10%
G1/8 G1/4 G1/2
2.5 2.5 4.8
2.1 2.1 2.7
G1/8 G1/4 G1/2
2.5 2.5 4.8
2.1 2.1 2.7

45
3/2, 5/2 Series S9 – G1/8 to G1/2
Characteristics Symbol Unit Series S9
and 5/3 G1/8
Way Valves for Actuation
General Features
Manual Control pneumatic electrical

use in Type Spool valve

Mounting 2 screws M5
EX areas Tube connection Thread
Thread G1/8 – 7.4 deep
Weight kg See page 48, 56, 64
Series Installation In any position
S9-G1/8 to G1/2 Ambient temperature range (1 Tmin. / max. °C -10 to +60 *

Medium temperature range (1 Tmin. / max. °C -10 to +60 *

Medium Filtered, unlibricated compressed air

– free from water and dirt to ISO8573-1
Pneumatic Characteristics
Nominal pressure pmin. / max. bar 6
Operating pressure range pmin. / max. bar 0–8 (10 – –
– permanent signal version pmin. / max. bar – 0–8 2–8
– impulse version pmin. / max. bar – 0–8 1.5–8(4
– with external pilot air pmin. / max. bar – – 0–8
* Valve Manifold Assemblies Nominal flow QN l/min 500 (450 bei 3/2 Way Valve)
with electrically actuated Actuation
valves -10 to +50°C
Manual control Direct
( Note:
1 Stroke mm 4.5
For use below freezing Actuation force Fb N 7 (2
point please contact us 10 (3
(2 Actuation force for valves Actuation force for See page 48
without spring return, panel mounting actuators
Actuation with rotary lever: Pneumatic Direct
5N Actuation pressure range
(3 Actuation force for valves
– permanent signal version pmin. / max. bar – 2–8 2–8
with spring return,
actuation with rotary lever: – impulse version pmin. / max. bar – 1.5–8 1.5–8(4
15N Electrical Electrical pilot operated
(4 Only for version with biased Certification EC Type Test Certificate for single valve:
position pneumatically not required for mechanical units in II 2G
actuated 2 – 8 bar,
electrically actuated
Category, Single valve II 2G c T4T135°C-10°C≤Ta≤+60°C
2.5 – 8 bar
type of ignition protection
(5 Version with biased position
2.5 – 8 bar Voltage type Alternating current (50/60Hz)
(6 Maximum power if warmed Nominal voltage Un V 230 ±10%
up to termal load limit Un V 110 ±10%
(7 Version “middle position Un V 24 ±10%
vented“ 1000 l/min Power rating at Un G1/8, G1/4, G1/2
(8 Version “middle position
VA (W) 3.1 (230V)
vented“ 3300 l/min
Version “middle position VA (W) 3.0 (110V)
pressured“ 3600 l/min VA (W) 2.5 (24V)
(9 5/3 Way Valve 2.5 – 8 bar Max. power at Un (6 G1/8, G1/4, G1/2
(10 Valves with panel mounting VA (W) 2.9 (230V)
actuators 2 – 8 bar VA (W) 2.8 (110V)
VA (W) 2.4 (24V)
Electrical protection IP IP65 (applise only to solenoid with cable)
Connection Cable – cable lengths see Order Instructions

46
 Series S9 Series S9
G1/4 G1/2
Manual Control pneumatic electrical Manual Control pneumatic electrical

Spool valve Spool valve

2 Screws M6 2 Screws M6
Thread Thread
G1/4 – 11 deep G1/2 – 16 deep
See page 52, 60, 66 See page 54, 62, 68
In any position In any position
-10 to +60 * -10 to +60 *

-10 to +60 * -10 to +60 *

Solids: Class 7 particle size <40 µm for gas Water content: pressure dew point + 3°C,
Class 4, but at least 5°C below minimum operating temperature

6 6
0–8 – – 0–8 – –
– 0–8 2–8 – 0–8 2.2–8
– 0–8 1.5–8(4 – 0–8 1.5–8(4
– – 0–8 – – 0–8
1300(7 3500(8

Direct Direct
6.5 9.4
10 (2 15 (2
15 (3 40 (3
– –

Direct Direct

2–8 2–8 2–8 – 2.2–8(9 2.2–8

1.5–8 1.5–8(4 1.5–8(4 – 1.5–8(5 1.5–8(4

EC Type Test Certificate for solenoid:

PTB-No. 03 Ex IEC 2019X and
PTB 03 ATEX 2018X toT5
Solenoid/individual use: II 2G EEx m II T5 -20°C≤Ta≤+50°C
Solenoid/manifold mounting: II 2G EEx m II T5 -20°C≤Ta≤+40°C
Direct current
24 ±10% Other voltages on request

G1/8, G1/4, G1/2

3.3 (24V)

G1/8, G1/4, G1/2

3.0 (24V)

47
3/2 Way Valves Weight (mass) kg
Description Type Weight (mass) kg
Series S9 Hand lever indexed S9 311-1/8 0.162
– with spring return S9 311RF-1/8 0.162
G1/8 Pneumatic, by permanent signal S9 361RF-1/8 0.137
Pneumatic, by impulse S9 361-1/8 0.147
Actuation:
– Hand lever Electrical, by permanent signal S9 381(S)RF-1/8 0.247
– Pneumatic Electrical, by impulse S9 381(S)-1/8 0.382
– Electrical pilot operated
– Electrical pilot operated
with external pilot air
– Panel mounting actuators Weight (mass) kg and action forces for valves with panel mounting actuators
for mounting diameter to Description Type Actuation force (N, Nm) Weight (mass) kg
DIN 43696
Rotary lever S9 312T-1/8 0.3 0.137
Versions: S9 312T-RF-1/8 0.3 0.137
– Normally closed
– Normally open Pushbutton S9 313T-RF-1/8 8.0 0.137
– With external pilot air Mushroom pushbutton S9 315T-RF-1/8 8.0 0.137
– Version to ATEX Standard
Locking switch S9 316T-1/8 9.0 0.202
Note: Rotary switch S9 317T-1/8 0.3 0.127
The “normally open“ valve S9
381S-RF-1/8 cannot be used Mushroom pushbutton S9 318T-1/8 10.0 0.137
on a P-supply manifold. emergency-0ff

Hand lever actuated

Type: S9 311-1/8, S9 311RF-1/8

94

29

20 7
11,5

19°
31,5
41

50

12
77

3
2
37
18

1
G1/8

10

5,5 22

5
40

For order instructions see page 70-72, characteristics see page 44-47
and for RPS manifolds see page 93-100, Valve Islands see page 87-92
Dimensions in mm

48
Pneumatically actuated – Type: S9 361-1/8, S9 361RF-1/8













 














  only for type
   S9361-1/8



Electrically actuated – Type: S9 381(S)-1/8, S9 381(S)RF-1/8 Solenoid for use in EX areas – Dimensions

Solenoid width 30 mm Cable lenth

***
22  see Order Instructions





10,5

*
M5

**
24,5
ca. 122

G1/8
33,5


42,5
24
110

12 (10)
pst X = 15,5 mm 
ca. 190

3(1)
69,5
5,6
3,2

36

2
For more information on valves to ATEX standards
37

18
5

1(3)
G1/8

see page 46, 47, 72

8

pst
10 (12)
16,6 **
15,5

* 5,5
56

15,5
only for type
40
S9 381 -1/8
S9 381S-1/8 63

* Manual override
** Operating pressure supply pst only for type S9 381S
*** Solenoid width = 30 mm on low wattage coil version

For order instructions see page 70-72, characteristics see page 44-47
P-Manifolds and for RPS manifolds see page 93-100, Valve Islands see page 87-92
Dimensions in mm

49
Basic valve for panel mounting actuatos – Type: S9 390RF-1/8 Mounting diameter

40 Mounting diameter Ø22 mm Mounting diameter Ø30 mm

28


 

28

38

47
12

76,5
74

 
37

2
18


1

10 G1/8
22 5,5

5
40
 
 

The actuators for these valves are interchangeable and can

be mounted with 180° displacement on the basic valve.
The actuators are not mounted upon delivery.

Rotary lever, indexed – Type: 12T-22, 12T-30, Pushbutton – Type: 13T-RF-22, 13T-RF-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mounting diameter Ø22 mm Mounting diameter Ø30 mm

 

∅ 

 
∅ ∅

 

























°




For order instructions see page 70-72, characteristics see page 44-47

Dimensions in mm

50
Mushroom pushbutton – Type: 15T-RF-22, 15T-RF-30 Locking switch – Type: 16T-22, 16T-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅ ∅

∅
  
































Rotary lever with spring return – Type: 12T-RF-22, 12T-RF-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mushroom pushbutton emergency-0ff – Type: 18T-22, 18T-30

  Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅
∅
 ∅ 





























°

°

Rotary switch – Type: 17T-22, 17T-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅














°


°


51
3/2 Way Valves Weight (mass) kg
Description Type Weight (mass)
Series S9 Hand lever, indexed S9 311-1/4 0.370
– with spring return S9 311RF-1/4 0.370
G1/4 Safety hand lever S9 311S-1/4 0.370
Rotary lever, indexed S9 312-1/4 0.370
Actuation systems:
– Hand lever – with spring return S9 312RF-1/4 0.370
– Pneumatic Pneumatic, by permanent signal S9 361RF-1/4 0.370
– Electrical pilot operated
– Electrical pilot operated with Pneumatic, by impulse S9 361-1/4 0.430
external pilot air – with biased position S9 362-1/4 0.430
Versions: Electrical, by permanent signal S9 381(S) RF-1/4 0.500
– Normally closed Electrical, by impulse S9 381(S)-1/4 0.600
– Normally open
– with biased position S9 382(S)-1/4 0.600
– With external pilot air
– With biased position
– Version to ATEX Standard
Hand lever actuated – Type: S9 311-1/4, S9 311RF-1/4

120
44
25 12

18°
17
42,5

55

66

12
98

3
G1/4

2
47

22

10

6,5 32

52

Safety hand lever actuated – Type: S9 311S-1/4

120

44
25 12
18°
17
42,5

55

66

12
98

3
G1/4

2
47

22

10

6,5 32

52

52
Rotary lever actuated – Type: S9 312-1/4, S9 312RF-1/4 Electrically actuated
– Type: S9 381(S)-1/4, S9 382(S)-1/4, S9 381(S)RF-1/4

79,5 32
33° 33° 44 22 ***
25 12
17
42,5

55

*
66

12

M5
65
98

10
3

G 1/8
28,5

30
G1/4

41
ca. 137
2

ca. 209
47

22

12 (10) 25

126

52
1 pst
3(1)

84

5,5
10 2 **

44
22
47

o 7,5
o 4,2
1(3)

G 1/4
6,5 32

11
6 pst

52 10 (12)
4,5

20
**
6,5
* only for type
Pneumatically actuated
62
S9 381-1/4
6 S9 381S-1/4
– Type: S9 361-1/4, S9 362-1/4, S9 361RF-1/4 S9 382-1/4
S9 382S-1/4

15,5
25
52

63
12,5

G1/8

22,5
21

33,5

44,5

12
* Manual override
5,5

3
** Operating pressure supply pst only for type S9 381S
76,5

*** Solenoid width = 30 mm

47

2
22

44
o 7,5
o 4,2
G1/4

1 on low wattage coil version

11

10

Note:
12,5

only for type The “normally open“ valve S9 381S-RF-1/4 cannot be used
6,5 4,5 32
S9 361-1/4 on a P-supply manifold.
6 S9 362-1/4
52

Solenoid for use in EX areas

Dimensions
Solenoid width 30 mm Cable lenth
 see Order Instructions





X = 15.5 mm 

For more information on valves to ATEX standards

see page 46, 47, 72

For order instructions see page 70-72, characteristics see page 44-47

Dimensions in mm

53
3/2 Way Valves Weight (mass) kg
Description Type Weight (mass)
Series S9 Hand lever, indexed S9 311-1/2 0.900
– with spring return S9 311RF-1/2 0.900
G1/2 Safety hand lever S9 311S-1/2 0.900
Rotary lever, indexed S9 312-1/2 0.950
Actuation systems:
– Hand lever –with spring return S9 312RF-1/2 0.950
– Pneumatic Pneumatic, by permanent signal S9 361RF-1/2 0.700
– Electrical pilot operated
– Electrical pilot operated with Pneumatic, by impulse S9 361-1/2 0.650
external pilot air – with biased position S9 362-1/2 0.650

Versions: Electrical, by permanent signal S9 381(S) RF-1/2 0.770

– Normally closed Electrical, by impulse S9 381(S)-1/2 1.008
– Normally open – with biased position S9 382(S)-1/2 1.008
– With external pilot air
– With biased position
– Version to ATEX Standard

Hand lever actuated – Type: S9 311-1/2, S9 311RF-1/2


 






















 
 


Safety hand lever actuated – Type: S9 311S-1/2


 





















 
 


54
Rotary lever actuated – Type: S9 312-1/2, S9 312RF-1/2 Electrically actuated
Type: S9 381(S)-1/2, S9 382(S)-1/2, S9 381(S)RF-1/2

   
 
  


















  












 











  





 

 6 deep



  


 


 
only for type
S9 581(S)-1/2
S9 582(S)-1/2

Pneumatically actuated – Type: S9 361-1/2, S9 361RF-1/2

* Manual override
** Operating pressure supply pst only for type S9 381S
 *** Solenoid width = 30 mm on low wattage coil version


  Note:


The “normally open“ valve S9 381S-RF-1/2 cannot be used

on a P-supply manifold.

























 6 deep






Solenoid for use in EX areas



only for type  Dimensions

S9 361-1/2
S9 362-1/2

Solenoid width 30 mm Cable lenth

 see Order Instructions





X = 21 mm 

For more information on valves to ATEX standards

see page 46, 47, 72

For order instructions see page 70-72, characteristics see page 44-47

Dimensions in mm

55
5/2 Way Valves Weight (mass) kg
Description Type Weight (mass)
Series S9 Hand lever, indexed S9 511-1/8 0.195
– with spring return S9 511RF-1/8 0.195
G1/8 Safety hand lever S9 511S-1/8 0.195
Pneumatic, by permanent signal S9 561RF-1/8 0.160
Actuation systems:
– Hand lever Pneumatic, by impulse S9 561-1/8 0.170
– Safety hand lever Electrical, by permanent signal S9 581(S)RF-1/8 0.280
– Pneumatic
– Electrical pilot operated Electrical, by impulse S9 581(S)-1/8 0.415
– Electrical pilot operated – with biased position S9 582-1/8 0.415
with external pilot air
– Panel mounting actuators
to DIN 43696 Weight (mass) and actuating forces for valves with panel mounting
Description Type Actuating force Weight (mass)
Versions: (N, Nm) (kg)
– With external pilot air
Rotary lever S9 512T-1/8 0.3 0.160
– With biased position
– Version to ATEX Standard S9 512T-RF-1/8 0.3 0.160
Pushbutton S9 513T-RF-1/8 8.0 0.150
Mushroom pushbutton S9 515T-RF-1/8 8.0 0.160
Locking switch S9 516T-1/8 9.0 0.225
Rotary switch S9 517T-1/8 0.3 0.150
Mushroom pushbutton S9 518T-1/8 10.0 0.160
emergency-0ff

Hand lever actuated – Type: S9 511-1/8, S9 511RF-1/8





 
°

























 




56
Safety hand lever actuated – Type: S9 511S-1/8 Electrically actuated
Type: S9 581(S)-1/8, S9 581(S)RF-1/8, S9 582-1/8


 22
***
 











10,5


M5

**

ca. 140

24,5


G1/8


33,5


42,5
24


128
14



pst



5,6
3,2

ca.208
4

87,5


18
55,5

G1/8
18
1

54
8

5

2

18
  16,6 3
pst

12
 **

15,5
* 5,5

Pneumatically actuated – Type: S9 561-1/8, S9 561RF-1/8

56
5

15,5
16

17

only for type

26

14
40
S9 581 -1/8
35

5 S9 581S-1/8 63
5,6
3,2

4
18
55,5

54
G1/8

1
18

* Manual override
80
8

2
18

4 ** Operating pressure supply pst only for type S9 581S

3
*** Solenoid width = 30 mm on low wattage coil version
12
8

16,6 5,5 only for type

S9 561-1/8
22 5

40
Solenoid for use in EX areas
Dimensions

Solenoid width 30 mm Cable lenth

 see Order Instructions





X = 15,5 mm 

For more information on valves to ATEX standards

see page 46, 47, 74

For order instructions see page 73, 74, characteristics see page 44-47

Dimensions in mm

57
Basic valve for panel mounting actuatos – Type: S9 590RF-1/8 Mounting diameter
40
Mounting diameter Ø22 mm Mounting diameter Ø30 mm
28


 

28

38

47
12

94,5

 
4
18
55,5
92


1

G1/8
2
3

10

22 5,5  

 
5

40

The actuators for these valves are interchangeable and can

be mounted with 180° displacement on the basic valve.
The actuators are not mounted upon delivery.

Rotary lever, indexed – Type: 12T-22, 12T-30 Mushroom pushbutton – Type: 15T-RF-22, 15T-RF-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mounting diameter Ø22 mm Mounting diameter Ø30 mm


∅ ∅
∅ ∅
 





























°

°


Pushbutton – Type: 13T-RF-22, 13T-RF-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅
 












58
Rotary switch – Type: 17T-22, 17T-30 Rotary lever with spring return – Type: 12T-RF-22, 12T-RF-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅ 


  ∅
∅


























°

°


°


°
Mushroom pushbutton emergency-0ff – Type: 18T-22, 18T-30 Locking switch – Type: 16T-22, 16T-30

Mounting diameter Ø22 mm Mounting diameter Ø30 mm Mounting diameter Ø22 mm Mounting diameter Ø30 mm

∅ ∅

 
∅ ∅

































For order instructions see page 73, 74, characteristics see page 44-47

Dimensions in mm

59
5/2 Way Valves Weight (mass) kg
Description Type Weight (mass)
Series S9 Hand lever, indexed S9 511-1/4 0.520
– with spring return S9 511RF-1/4 0.520
G1/4 Safety hand lever S9 511S-1/4 0.520
Rotary lever, indexed S9 512-1/4 0.520
Actuation systems:
– Hand lever – with spring return S9 512RF-1/4 0.520
– Safety hand lever Pneumatic, by permanent signal S9 561RF-1/4 0.490
– Pneumatic
– Electrical pilot operated Pneumatic, by impulse S9 561-1/4 0.510
– Electrical pilot operated with – with biased position S9 562-1/4 0.510
external pilot air
Electrical, by permanent signal S9 581(S) RF-1/4 0.600
Versions Electrical, by impulse S9 581(S)-1/4 0.700
– With external pilot air – with biased position S9 582(S)-1/4 0.700
– With biased position
– Version to ATEX Standard

Hand lever actuated – Type: S9 511-1/4, S9 511RF-1/4




 

°
























 



Safety hand lever actuated – Type: S9 511S-1/4




 

























 




60
Rotary lever actuated Electrically actuated
Type: S9 512-1/4, S9 512RF-1/4 Type: S9 581(S)-1/4, S9 582(S)-1/4, S9 581(S)RF-1/4



79,5

33° 33° 44

25 12
17
43,5


55



66



14


 



65





5
120


4
22



G1/4





67

22











22

2



3 




12 
6,5 32


6

52 


only for type




Pneumatically actuated 


Type: S9 561-1/4, S9 562-1/4, S9 561RF-1/4 

* Manual override
** Operating pressure supply pst only for type S9 581S
25
*** Solenoid width = 30 mm on low wattage coil version
12,5

G1/8

22,5
22

33,5

44,5

14

5
Solenoid for use in EX areas
5,5
66

4
Dimensions
22

o 7,5
o 4,2
98,5

G1/4
111

1
67

22

11

2
22

Solenoid width 30 mm
4,5 Cable lenth
3  see Order Instructions
12
12,5

only for type

6,5 32


S9 561-1/4




6 S9 562-1/4
52


X = 15,5 mm 

For more information on valves to ATEX standards

see page 46, 47, 74

For order instructions see page 73, 74, characteristics see page 44-47

Dimensions in mm

61
5/2 Way Valves Weight (mass) kg

Series S9 Description
Hand lever, indexed
Type
S9 511-1/2
Weight (mass)
0.120
– with spring return S9 511RF-1/2 0.120
G1/2
Safety hand lever S9 511S-1/2 0.120
Actuation systems: Rotary lever, indexed S9 512-1/2 0.120
– Hand lever
– with spring return S9 512RF-1/2 0.120
– Safety hand lever
– Pneumatic Pneumatic, by permanent signal S9 561RF-1/2 0.800
– Electrical pilot operated
Pneumatic, by impulse S9 561-1/2 0.900
Versions: – with biased position S9 562-1/2 0.900
– With external pilot air
Electrical, by permanent signal S9 581(S) RF-1/2 1.000
– With biased position
– Version to ATEX Standard Electrical, by impulse S9 581(S)-1/2 1.045
– with biased position S9 582-1/2 1.045

Hand lever actuated – Type: S9 511-1/2, S9 511RF-1/2


 




























 

 



Safety hand lever actuated – Type: S9 511S-1/2


 



























 

 



62
Rotary lever actuated – Type: S9 512-1/2, S9 512RF-1/2 Electrically actuated
Type: S9 581(S)-1/2, S9 582-1/2, S9 581(S)RF-1/2

   

 

  




  










  














  



















 6 deep

  



 

 



 






Pneumatically actuated only for type
Type: S9 561-1/2, S9 561RF-1/2, S9 562-1/2 S9 581-1/2
S9 582-1/2
S9 581S-1/2



* Manual override
 


** Operating pressure supply pst only for type S9 581S

*** Solenoid width is 30 mm on low wattage coil version










 Solenoid for use in EX areas



 Dimensions










 6 deep






Solenoid width 30 mm Cable lenth
  see Order Instructions



only for type



S9 561-1/2


S9 562-1/2


X = 21 mm 

For more information on valves to ATEX standards

see page 46, 47, 74

For order instructions see page 73,74, characteristics see page 44-47

Dimensions in mm

63
5/3 Way Valves Weight (mass) kg
Description Type * Weight (mass)
Series S9 Hand lever S9 511.-1/8 0,195
– with spring return S9 511RF.-1/8 0,195
G1/8 Safety hand lever S9 511S.-1/8 0,195
Pneumatic, by permanent signal S9 561RF.-1/8 0,180
Actuation systems:
– Hand lever Electrical, by permanent signal S9 581RF.-1/8 0,425
– Safety hand lever Electrical, by permanent signal S9 581S-RF.-1/8 0,425
– Pneumatic
– Electrical pilot operated * Type code for middle position functions
G = middle position closed
Versions: E = middle position exhausted
– With external pilot air B = middle position pressurized
– Version to ATEX Standard

Hand lever actuated – Type: S9 511.-1/8, S9 511RF.-1/8



 



°
























 




Safety hand lever actuated – Type: S9 511S.-1/8

94
29
20 7
19
°
11,5
31

41

48

14
G1/8

5
95

4
18
55,5

18

1
2
18

12

5,5 22
5

40

64
Pneumatically actuated – Type: S9 561RF.-1/8

16

17
26
14

35
5
5,6
3,2

18
55,5

54
G1/8
1

18
88
8

18
4
3

12

16,6 5,5
22 5

40

Electrically actuated – Type: S9 581(S-)RF.-1/8 Solenoid for use in EX areas

Dimensions
22
**

Solenoid width 30 mm Cable lenth

 see Order Instructions
10,5

*
M5
ca. 140


pst ***



33,5
24

42,5
128

14
ca. 208

5
5,6
3,2

4
87,5

18


55,5

G1/8

18

1
8

X = 15,5 mm 
2
18

4
16,6 3

12 For more information on valves to ATEX standards

see page 46, 47, 77
15,5

pst ***

* 5,5
56

15,5
40

63

* Manual override
** Solenoid width = 30 mm on low wattage coil version
*** Operating pressure supply pst only for type S9 581S

For order instructions see page 75-77, characteristics see page 44-47

Dimensions in mm

65
5/3 Way Valves Weight (mass) kg
Description Type * Weight (mass)
Series S9 Hand lever, indexed S9 511.-1/4 0.520
– with spring return S9 511RF.-1/4 0.530
G1/4 Safety hand lever S9 511S.-1/4 0.520
Rotary lever, indexed S9 512.-1/4 0.520
Actuation systems:
– Hand lever –with spring return S9 512RF.-1/4 0.530
– Safety hand lever Pneumatic, by permanent signal S9 561RF.-1/4 0.530
– Pneumatic
– Electrical pilot operated Electrical, by permanent signal S9 581RF.-1/4 0.700
* Type code for middle position functions
Versions: G = middle position closed
– Version to ATEX Standard E = middle position exhausted
B = middle position pressurized

Hand lever actuated – Type: S9 511.-1/4, S9 511RF.-1/4





 



























 



Safety hand lever actuated – Type: S9 511S.-1/4




 


























 



66
Rotary lever actuated – Type: S9 512.-1/4, S9 512RF.-1/4 Electrically actuated – Type: S9 581RF.-1/4
32



**
22
 
 



*


M5

10




29,5

G1/8

30


41
14

ca. 159
25

52


ca.231


148



5,5



4


o 7,5
o 4,2
22
106

G 1/4

22
1

67

66

11




22

4,5
3



6,5
12
 

20


 6 *

62
Pneumatically actuated – Type: S9 561RF.-1/4
15,5

52

63





* Manual override






** Solenoid width is 30 mm on low wattage coil version
























Solenoid for use in EX areas




Dimensions


Solenoid width 30 mm Cable lenth

   see Order Instructions








X = 15,5 mm 

For more information on valves to ATEX standards

see page 46, 47, 77

For order instructions see page 75-77, characteristics see page 44-47

Dimensions in mm

67
5/3 Way Valves Weight (mass) kg
Description Type * Weight (mass)
Series S9 Hand lever, indexed S9 511.-1/2 1.200
– with spring return S9 511RF.-1/2 1.200
G1/2 Safety hand lever S9 511S.-1/2 1.200
Rotary lever, indexed S9 512.-1/2 1.200
Actuation systems:
– Hand lever – with spring return S9 512RF.-1/2 1.200
– Safety hand lever Pneumatic, by permanent signal S9 561RF.-1/2 0.900
– Pneumatic
– Electrical pilot operated Electrical, by permanent signal S9 581RF.-1/2 1.045
* Type code for middle position functions
Versions: G = middle position closed
– Version to ATEX Standard E = middle position exhausted
B = middle position pressurized

Hand lever actuated – Type: S9 511.-1/2, S9 511RF.-1/2


 



























 
 


Safety hand lever actuated – Type: S9 511S.-1/2


 


























 
 


68
Rotary lever actuated – Type: S9 512.-1/2, S9 512RF.-1/2 Electrically actuated – Type: S9 581RF.-1/2

 
70 40

68 32,5


21 22 **



















29
39

57



14

73

5

G1/2
4

32


201,5
1

283

190
149

100

16
32
 

9,56 deep
5,3
6,5 2

32
 
3
 *
12

7
29
Pneumatically actuated – Type: S9 561RF.-1/2

70
70

6,5

7 40
G1/8

* Manual override
9

** Solenoid width is 30 mm on low wattage coil version

19
29

47

14
63

5
G1/2

4
32

140

1
158

139

100

16
32

9,5 6 deep
5,3

2
Solenoid for use in EX areas
32

3
Dimensions
12

32,5 Solenoid width 30 mm Cable lenth

 see Order Instructions





X = 21 mm 

For more information on valves to ATEX standards

see page 46, 47, 77

For order instructions see page 75-77, characteristics see page 44-47

Dimensions in mm

69
3/2 Way Valves – Standard versions
Actuation System Symbol Mounting Order Instructions Page
Ø (mm) Type Order No.
Hand lever, 2 S9 311-1/8 PA 10293 48
12
indexed S9 311-1/4 PA 12708 52
1 3
S9 311-1/2 PA 16404 54
Hand lever, 2 S9 311RF-1/8 PA 10294 48
12 10
spring return S9 311RF-1/4 PA 12709 52
1 3
S9 311RF-1/2 PA 16405 54
Hand lever 12 2
secured in 2 switching S9 311S-1/4 PA 12710 52
positions
1 3
S9 311S-1/2 PA 16406 54
Rotary lever, 2
12
indexed S9 312-1/4 PA 12711 53
1 3
S9 312-1/2 PA 16407 45
Rotary lever, 2
12 10
spring return S9 312RF-1/4 PA 12712 53
1 3
S9 312RF-1/2 PA 16408 55
Pneumatic, 2 S9 361RF-1/8 PA 10295 49
by permanent signal 12 10
S9 361RF-1/4 PA 12713 53
1 3
S9 361RF-1/2 PA 16409 55
Pneumatic, 2 S9 361-1/8 PA 10296 49
by impulse 12 10
S9 361-1/4 PA 12714 53
1 3
S9 361-1/2 PA 16410 55
Pneumatic, by impulse, 2
with biased position 12 10
S9 362-1/4 PA 12715 53
1 3
S9 362-1/2 PA 16411 55
Basic valve for 2 S9 390RF-1/8 PA 10307 50
10
panel mounting 12

1 3

Rotary lever, 22 12T-22 KX 9355 50

indexed 30 12T-30 KX 9314

Rotary lever, 22 12T-RF-22 KX 9356 51

spring return 30 12T-RF-30 KX 9315

Pushbutton 22 13T-RF-22 KX 9357 50

30 13T-RF-30 KX 9316

Mushroom pushbutton 22 15T-RF-22 KX 9358 51

30 15T-RF-30 KX 9317

Locking switch 22 16T-22 KX 9359 51

30 16T-30 KX 9318

70
Actuation System Symbol Mounting Order Instructions Page
Ø (mm) Type Order No.
Rotary switch 22 17T-22 KX 9360 51
30 17T-30 KX 9319

Mushroom pushbutton 22 18T-22 KX 9361 51

emergency-0ff 30 18T-30 KX 9320

Electrical 2 S9 381RF-1/8-NC-.. PA 10297-..33 49

by permanent signal 12 10
S9 381RF-1/4-NC-.. PA 12716-..33 53
1 3
S9 381RF-1/2-NC-.. PA 16412-..33 55
2 S9 381RF-1/8-NO-.. PA 10298-..33 49
10 12
S9 381RF-1/4-NO-.. PA 12717-..33 53
1 3 S9 381RF-1/2-NO-.. PA 16413-..33 55
with external pilot air 2
S9 381S-RF-1/8-.. PA 10300-..33 49
14 12
S9 381S-RF-1/4-.. PA 12719-..33 53
pst 1 3 S9 381S-RF-1/2-.. PA 16415-..33 55
Electrical 2 S9 381-1/8-.. PA 10299-..33 49
by impulse 12 10
S9 381-1/4-.. PA 12718-..33 53
1 3 S9 381-1/2-.. PA 16414-..33 55
Electrical, by impulse, 2 S9 381S-1/8-.. PA 10301-..33 49
with external pilot air 14 12
S9 381S-1/4-.. PA 12720-..33 53
pst 1 3 pst
S9 381S-1/2-.. PA 16417-..33 55
Electrical by impulse, 2
with biased position 14 12
S9 382-1/4-.. PA 12721-..33 53
1 3
S9 382-1/2-.. PA 16418-..33 55
with external pilot air 2
14 12
S9 382S-1/4-.. PA 12722-..33 53
pst
pst 1 3
S9 382S-1/2-.. PA 16419-..33 55

Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Standard version 230V 50/60Hz 110 V = 61 –
24V = 60V 50/60Hz 02 –
Low wattage version 24V = 13 –
230V 50/60Hz 69 –
EX Area versions to ATEX standard see page 72

71
EX Area versions to ATEX Standard
Category, type of ignition protection
Single valve: II 2G c T4 T135°C -10°C≤Ta≤+60°C
Solenoid/individual use: II 2G EEx m II T5 -20°C≤Ta≤+50°C
Solenoid/manifold mounting: II 2G EEx m II T5 -20°C≤Ta≤+40°C
Solenoid version Nominal Applicable for Key code ATEX Type ad-
voltage diton
Solenoid 24V = 48 Atex
– with cable 1.2 m
– with cable 3 m 24V = 45 Atex
– with cable 5 m 24V = 46 Atex
– with cable 10 m 24V = 47 Atex
– with cable 1.2 m 24V 50/60Hz 99 Atex
– with cable 1.2 m 110V 50/60Hz 97 Atex
– with cable 1.2 m 230V 50/60Hz 98 Atex
Example for valves in ATEX-Version:
– for valves Series S9-G1/8, S9-G1/4, S9-G1/2
Please add behind the Standard Order No. “ATEX“
Type: S9 381RF-1/8-NC-4633
Order No. PA10297-4633ATEX

72
Order Instructions – 5/2 Way Valves – Standard versions
Actuation System Symbol Mounting Order Instructions Page
Ø (mm) Type Order No.
Hand lever, 4 2 S9 511-1/8 PA 10308 56
14
indexed S9 511-1/4 PA 12671 60
51 3
S9 511-1/2 PA 16367 62
Hand lever, 4 2 S9 511RF-1/8 PA 10309 56
14 12
spring return S9 511RF-1/4 PA 12672 60
513
S9 511RF-1/2 PA 16366 62
Hand lever 14
4 2 S9 511S-1/8 PA 10368 57
secured in 2 switching S9 511S-1/4 PA 12673 60
positions
513
S9 511S-1/2 PA 16368 62
Rotary lever, 14
4 2

indexed S9 512-1/4 PA 12674 61

51 3
S9 512-1/2 PA 16378 63
Rotary lever, 4 2
14 12
spring return S9 512RF-1/4 PA 12675 61
513
S9 512RF-1/2 PA 16379 63
Pneumatic, 4 2 S9 561RF-1/8 PA 10310 57
12
by permanent signal 14
S9 561RF-1/4 PA 12676 61
513
S9 561RF-1/2 PA 16165 63
Pneumatic, 4 2 S9 561-1/8 PA 10311 57
by impulse 14 12
S9 561-1/4 PA 12677 61
513
S9 561-1/2 PA 16166 63
Pneumatic, 4 2
by impulse, 14 12
S9 562-1/4 PA 12678 61
with biased position
513
S9 562-1/2 PA 16167 63
Basic valve for 4 2 S9 590RF-1/8 PA 10320 58
panel mounting 14
12

51 3

Rotary lever, 22 12T-22 KX 9355 58

indexed 30 12T-30 KX 9314

Rotary lever, 22 12T-RF-22 KX 9356 59

spring return 30 12T-RF-30 KX 9315

Pushbutton 22 13T-RF-22 KX 9357 58

30 13T-RF-30 KX 9316

Mushroom pushbutton 22 15T-RF-22 KX 9358 58

30 15T-RF-30 KX 9317

Locking switch 22 16T-22 KX 9359 59

30 16T-30 KX 9318

73
Order Instructions – 5/2 Way Valves – Standard versions
Actuation System Symbol Mounting Order Instructions Page
Ø (mm) Type Order No.
Rotary switch 22 17T-22 KX 9360 58
30 17T-30 KX 9319

Mushroom pushbutton 22 18T-22 KX 9361 59

Emergency-Off 30 18T-30 KX 9320

Electrical, 4 2 S9 581RF-1/8-.. PA 10312-..33 57

14 12
by permanent signal S9 581RF-1/4-.. PA 12679-..33 61
5 13
S9 581RF-1/2-.. PA 16171-..33 63
with external pilot air 4 2 S9 581S-RF-1/8-.. PA 10314-..33 57
14 12
S9 581S-RF-1/4-.. PA 12681-..33 61
pst 513
S9 581S-RF-1/2-.. PA 16174-..33 63
Electrical, 4 2 S9 581-1/8-.. PA 10313-..33 57
14 12
by impulse
S9 581-1/4-.. PA 12680-..33 61
513
S9 581-1/2-.. PA 16172-..33 63
with external pilot air 4 2 S9 581S-1/8-.. PA 10315-..33 57
14 12
S9 581S-1/4-.. PA 12682-..33 61
pst pst
5 13
S9 581S-1/2-.. PA 16175-..33 63

Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Standard version 230V 50/60Hz 110 V = 61 –
24V = 60V 50/60Hz 02 –
Low wattage version 24V = 13 –
230V 50/60Hz 69 –
EX Area versions to ATEX Standard
Category, type of ignition protection
Single valve: II 2G c T4 T135°C -10°C≤Ta≤+60°C
Solenoid/individual use: II 2G EEx m II T5 -20°C≤Ta≤+50°C
Solenoid/manifold mounting: II 2G EEx m II T5 -20°C≤Ta≤+40°C
Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Solenoid 24V = 48 Atex
– with cable 1.2 m
– with cable 3 m 24V = 45 Atex
– with cable 5 m 24V = 46 Atex
– with cable 10 m 24V = 47 Atex
– with cable 1.2 m 24V 50/60Hz 99 Atex
– with cable 1.2 m 110V 50/60Hz 97 Atex
– with cable 1.2 m 230V 50/60Hz 98 Atex
Example for valves in ATEX-Version:
– for valves Series S9-G1/8, S9-G1/4, S9-G1/2
Please add behind the Standard Order No. “ATEX“
Type: S9 581RF-1/8-4633
Order No. PA10312-4633ATEX

74
Order Instructions – 5/3 Way Valves – Standard versions
Actuation System Symbol Order Instructions Page
Type Order No.
Hand lever, 4 2
S9 511G-1/8 PA 10321 64
secured in 3 operating 14
S9 511G-1/4 PA 12687 66
positions
513 S9 511G-1/2 PA 16369 68
4 2 S9 511E-1/8 PA 10322 64
14
S9 511E-1/4 PA 12688 66
513 S9 511E-1/2 PA 16370 68
4 2 S9 511B-1/8 PA 10323 64
14
S9 511B-1/4 PA 12689 66
513
S9 511B-1/2 PA 16371 68
Hand lever, 4 2 S9 511RFG-1/8 PA 10324 64
spring return to 14 12
S9 511RFG-1/4 PA 12690 66
middle position
513
S9 511RFG-1/2 PA 16372 68
4 2 S9 511RFE-1/8 PA 10325 64
14 12
S9 511RFE-1/4 PA 12691 66
513 S9 511RFE-1/2 PA 16373 68
4 2 S9 511RFB-1/8 PA 10326 64
14 12
S9 511RFB-1/4 PA 12692 66
51 3
S9 511RFB-1/2 PA 16374 68
Hand lever, 14 4 2 S9 511SG-1/8 PA 10327 64
secured in 3 operating S9 511SG-1/4 PA 12693 66
positions
5 13
S9 511SG-1/2 PA 16375 68
14 4 2 S9 511SE-1/8 PA 10328 64
S9 511SE-1/4 PA 12694 66
513
S9 511SE-1/2 PA 16376 68
14 4 2 S9 511SB-1/8 PA 10329 64
S9 511SB-1/4 PA 12695 66
513
S9 511SB-1/2 PA 16377 68
Rotary lever, 4 2
indexed in 3 operating 14
S9 512G-1/4 PA 12696 67
positions
513
S9 512G-1/2 PA 16380 69
4 2
14
S9 512E-1/4 PA 12697 67
513
S9 512E-1/2 PA 16381 69
4 2
14
S9 512B-1/4 PA 12698 67
513
S9 512B-1/2 PA 16382 69

75
Actuation System Symbol Order Instructions Page
Type Order No.
Rotary lever, 4 2
14 12
spring return to S9 512RFG-1/4 PA 12699 67
middle position 513
S9 512RFG-1/2 PA 16383 69
4 2
14 12
S9 512RFE-1/4 PA 12700 67
513
S9 512RFE-1/2 PA 16384 69
4 2
14 12
S9 512RFB-1/4 PA 12701 67
51 3
S9 512RFB-1/2 PA 16385 69
Pneumatic, 4 2 S9 561RFG-1/8 PA 10330 65
by permanent signal 14 12
S9 561RFG-1/4 PA 12702 67
51 3
S9 561RFG-1/2 PA 16168 69
spring return to 4 2 S9 561RFE-1/8 PA 10331 65
middle position 14 12
S9 561RFE-1/4 PA 12703 67
513
S9 561RFE-1/2 PA 16169 69
4 2 S9 561RFB-1/8 PA 10332 65
14 12
S9 561RFB-1/4 PA 12704 67
5 13
S9 561RFB-1/2 PA 16170 69
Electrical 4 2 S9 581RFG-1/8-.. PA 10333-..33 65
by permanent signal 14 12
S9 581RFG-1/4-.. PA 12705-..33 67
51 3
S9 581RFG-1/2-.. PA 16176-..33 69
spring return to 4 2 S9 581RFE-1/8-.. PA 10334-..33 65
middle position 14 12
S9 581RFE-1/4-.. PA 12706-..33 67
513
S9 581RFE-1/2-.. PA 16177-..33 69
4 2 S9 581RFB-1/8-.. PA 10335-..33 65
14 12
S9 581RFB-1/4-.. PA 12707-..33 67
513
S9 581RFB-1/2-.. PA 16178-..33 69

For complete Type- and Order No. - see page 77

76
Actuation System Symbol Order Instructions Page
Type Order No.
Electrical 4 2 S9 581S-RFG-1/8-.. PA 10377-..33 65
14 12
by permanent signal S9 581S-RFG-1/4-.. PA 12925-..33 67
pst 513 pst

spring return to 4 2 S9 581S-RFE-1/8-.. PA 10379-..33 65

middle position 14 12
S9 581-RFE-1/4-.. PA 12923-..33 67
pst 513 pst

with external pilot air 4 2 S9 581S-RFB-1/8-.. PA 10378-..33 65

14 12
S9 581S-RFB-1/4-.. PA 12924-..33 67
pst 513 pst

Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Standard version 230V 50/60Hz 110 V = 61 –
24V = 60V 50/60Hz 02 –
Low wattage version 24V = 13 –
230V 50/60Hz 69 –
EX Area versions to ATEX Standard
Category, type of ignition protection
Single valve: II 2G c T4 T135°C -10°C≤Ta≤+60°C
Solenoid/individual use: II 2G EEx m II T5 -20°C≤Ta≤+50°C
Solenoid/manifold mounting: II 2G EEx m II T5 -20°C≤Ta≤+40°C
Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Solenoid 24V = 48 Atex
– with cable 1.2 m
– with cable 3 m 24V = 45 Atex
– with cable 5 m 24V = 46 Atex
– with cable 10 m 24V = 47 Atex
– with cable 1.2 m 24V 50/60Hz 99 Atex
– with cable 1.2 m 110V 50/60Hz 97 Atex
– with cable 1.2 m 230V 50/60Hz 98 Atex
Example for valves in ATEX-Version:
– for valves Series S9-G1/8, S9-G1/4, S9-G1/2
Please add behind the Standard Order No. “ATEX“
Type: S9 581RFG-1/8-4633
Order No. PA10333-4633ATEX

77
3/2, 5/2 and Weight (mass) kg
Description Weight (mass) – Connection size
5/3 Way Valves G1/8 G1/4
Series S9 3/2 Way Valve, by permanent signal 0.137 0.370
3/2 Way Valve, by impulse 0.147 0.430
G1/8, G1/4 5/2 Way Valve, by permanent signal 0.160 0.490
5/2 Way Valve, by impulse 0.170 0.510
Actuation systems: 5/3 Way Valve, by permanent signal 0.180 0.530
Pneumatic
– AND
– OR Possible combinations:
– TIMER

Versions: Basic valves

Freely selectable types 
– See Order information  
– All Timer-Versions on
request  
 
 
Actuation System (14)

 
  
   
Actuation System (12)
 
  

 
 
 
   
   


  
 

 
    



For more information on * RFG = middle position closed

standard valves see Instruc- RFE = middle position exhausted
tions sheets on page 44-69 RFB = middle position pressurized

Dimensions in mm

78
Valve Combinations with Logic Elements – 3/2, 5/2 and 5/3 Way Valves
Pneumatic



Actuation 61
OR



  



 Actuation 63
Timer Dimension Table and adjustment ranges
Actuation 64
Adjustment range Dimension A [mm]
Standard version: 0.1 to 15 103 (133*)
Countersunk


adjustment screw 0.1 to 30 117 (147*)
On request: 0.1 to 60 150 (180*)
Rotary knob version * Version with rotary knob


  
(optional)
AND



  
Actuation 65




 
 


 


 

3/2 Way Valve  

5/2 and 5/3 Way Valves




 
 UND

Actuation 65
 


Timer Dimension Table and adjustment ranges

Actuation 64 Adjustment range Dimension A [mm]
Standard version: 0.1 to 15 103 (133*)
Countersunk
adjustment screw 0.1 to 30 117 (147*)
On request: 0.1 to 60 150 (180*)
Rotary knob version


  OR * Version with rotary knob


Actuation System (optional)
Pneumatic
Actuation 61

Order Instructions

S9 5 63 / 65 – RFG – 1/4

Version Connection size

3 3 Way Valve 1/8 G1/8
5 5 Way Valve 1/4 G1/4

Actuation System (14) Mid position function

61 Pneumatic (only with 5/3 Way Valves)
63 OR RFG closed
64 Timer* – all Timer- RFE vented
Versions on request RFB pressurized

65 AND Actuation System (14)

* only with connection size RF spring return
G1/4
61 pneumatic
63 OR
64 Timer* – all Timer-
Versions on request

65 AND
Dimensions in mm * only with Connection size
G1/4

79
80
Contents Solenoid Poppet
Version Actuation
Characteristics
Page
Dimensions Order Instructions
Valves
Overview
3/2 Way Valves electrical 82 83 83 directly actuated
Series EV-M5 (G1/8)
Series EV-M5 (G1/8)
3/2 Way Valves electrical 84 85 86
Series V9-G1/8 Series V9-G1/8

81
3/2 Way Characteristics – Series EV
Characteristics Symbol Unit Description
Screw-In Valve General Features
Series EV Actuation Electrical directly operated
Type Poppet valve, normally closed
G1/8-M5 Mounting Screws into thread G1/8
Tube connection Thread
Actuation System: Port size Port 1: M5, port 2: G1/8
– Electrical, directly actuated
Weight kg 0.1
Nominal diameter mm 1
Installation in any position
Ambient temperature Tmin. / max. °C -10 to Note :
range +60 Please consult us for operating
Medium temperature Tmin. / max. °C -10 to temperatures below 0° C
range +60
Medium Filtered compressed air (30µ)
Lubrication With or without oil mist lubrication
(We recommend the use of mineral oil type VG
32 to ISO 3448)
Pneumatic Characteristics
Nominal pressure pmin. / max. bar 6
Operating pressure range pmin. / max. bar 0 – 10
Nominal flow QN l/min 30
Actuation
Electrical Direct
Voltage type Alternating Direct current
current
(50/60Hz)
Nominal voltage (1

– Standard version Un V 230 ±10% 24 ±10% other voltages on

request
– Low wattage version Un V 230 ±10% 24 ±10%
Initial power consumption
– Standard version VA (W) 11 4.8
– Low wattage version VA (W) 7.8 2.7
Continuous consumption
– Standard version VA (W) 8.5 4.8
– Low wattage version VA (W) 4.9 2.7
Duty cycle ED % 100
Electrical protection IP 65 to DIN 40050 (applise only to
solenoid with plug)
Connection Plug to DIN EN 175301-803
form B – industrial standard,
Low wattage version form A
(1 see Order Instructions

82
3/2 Way Valve – Type: EV 381RF-M5





 









 


Order Instructions – 3/2 Way Screw-In Valve – Series EV

Actuation Symbol Order Instructions
Type Order No.
Electrical, 2 EV 381RF-M5-.. PD25076-..33
12 10
by permanent signal
13

Solenoid version Nominal voltage Key code

Cast encapsulated 24V = 02
housing 230V 50/60Hz 61
Other voltages on request

Dimensions in mm

83
3/2 Way Valves Characteristics – Series V9-G1/8
Characteristics Symbol Unit Description
Series V9 General Features
Type Poppet valve
NW 1.3 and 2.5 Mounting 2 Screws M3 (NW 2.5: 2 x M4)
Tube connection Thread
Actuation System:
– Electrically actuated, Thread G1/8 – 8 deep
directly actuated Weight kg NW 1.3: 0.140
NW 2.5: 0.320
Versions:
Installation In any position
Threaded version
– Normally closed Ambient temperature Tmin. / max. °C -10 Note :
– Normally open range (1 +60 Please consult us for operating
– With manual override Medium temperature Tmin. / max. °C -10 temperatures below 0° C
range (1 +70
P-moulding mounting:
– See Order Instructions Medium Filtered compressed air
Lubrication With or without oil mist lubrication
(We recommend the use of mineral oil type VG
32 to ISO 3448)
Pneumatic Characteristics
Nominal pressure pmin. / max. bar 6
Operating pressure pmin. / max. bar NW 1.3: 0–10
range NW 2.5: 0-7
Nominal flow QN l/min NW 1.3: 37
NW 2.5: 150
Actuation
Electrical Direct
Voltage type Alternating Direct current
current (50/60Hz)
Nominal voltage
– Standard version Un V 230 ±10% 24 ±10% other voltages
– Low wattage version Un V 230 ±10% 24 ±10% on request
(not for (not for
V9-NW 2.5) V9-NW 2.5)
Initial power consumption
– Standard version VA (W) NW 1.3: 11 NW 1.3: 4.8
NW 2.5: 11.5 NW 2.5: 10
– Low wattage version VA (W) 7.8 2.7
Continuous consumption
– Standard version VA (W) NW 1.3: 8.5 NW 1.3: 4.8
NW 2.5: 7.5 NW 2.5: 7.5
– Low wattage version VA (W) 4.9 2.7
Duty cycle ED % 100
Electrical protection IP IP 65 to DIN 40050 (applise only to solenoid
with connector)
Connection NW 1.3: connector to DIN EN 175301-803
form B – industrial standard
NW 2.5: connector to DIN EN 175301-803
form A – industrial standard

84
 (1
not suitable for P-supply
Type: V9 381RF-1/8NG (NO(1)– NW 1.3
manifold mounting
Type: V9 381H-RF-1/8NG (NO(1)– NW 1.3
 




  




∅






∅










 

 



* Low wattage version is 30 mm wide:

– therefore to mount these on a P-Supply Manifold, special measures are needed.
** Manual override

Type: V9 381RF-1/8NG – NW 2.5

Type: V9 381H-RF-1/8NG – NW 2.5







 


























 


* Manual override

For order instructions see page 86

Dimensions in mm

85
Order Instructions – 3/2 Way Valves – Series V9
Actuation System Symbol Nominal Order Instructions Page
Size Type Order No.
(mm)
2
Electrical, 12 10 NW 1.3 V9 381RF-1/8-NC-.. PA 10362-..33 84, 85
by permanent signal
13 NW 2.5 V9 381RF-1/8-NC-.. PA 10369-..33 84, 85
2
12
10
NW 1.3 V9 381H-RF-1/8-NC-.. PA 10363-..33 84, 85
1 3
NW 2.5 V9 381H-RF-1/8-NC-.. PA 10370-..33 84, 85
2
12 10
NW 1.3 V9 381H-RF-1/8-NO-.. PA 10367-..33 84, 85
1 3

Solenoid version Nominal voltage Applicable for Key code

Standard version 230V 50/60Hz 110 V = 61
24V = 60V 50/60Hz 02
Low wattage version 24V = 13
230V 50/60Hz 69
Other voltages on request

Order Instructions – Accessories for P-Supply Manifold Mounting

Description for NW Order No.
P-Manifold PL-1/8-.. 1.3 PD32763-....*
P-Manifold PLK-1/8-.. 1.3 PD37174-....*
P-Manifold PL-1/4-.. 2.5 PD32765-....*
P-Manifold PLK-1/4-.. 2.5 PD32175-....*
* Complete order no. with no. of valve

The delivery includes:

P-Manifold complete incl. mounting kit

86
Contents Valve Islands
Version Actuating Page
electrical Characteristics Dimension Order
over Table Instructions
Series IM20-G1/8
Valve Islands with Sub-D plug 88 89, 90 91 Series IM20-G1/4
Multipole Connector industrial connector
Accessories – ­– 92

87
Valve Islands with Multipole Connector
Characteristics Symbol Unit Description
General Features
Type IM20-1/8 IM20-1/4
Mounting 4 Screws – see drawing 4 Screws – see drawing
Connection size
– air supply and exhaust G1/4 both sides G3/8 both sides
– valve outlets G1/8 G1/4
Size for valve positions 22 33
Installation In any position
Ambient and medium Tmin °C –10 Note: Please consult us for operating temperatures below 0° C
temperature range Tmax °C +50
Medium Filtered compressed air
Lubrication With or without oil mist lubrication
(We recommend the use of mineral oil type VG 32 to ISO 3448)
Material
– Base plate Al
– Valve housing Al
– Seals NBR
Durability of valves 10 x 106 operations
No. of valves positions 4 – 6 – 8 – 10 – 12 –14–16 (1

No. of switching outputs max. 24

No. of sensor inputs max. 32
Pneumatic characteristics
Nominal pressure pn bar 6
Operating pressure range pmin bar 2.5
pmax bar 10
Nominal flow Qn l/min 500 1300 (2

Actuation
Electrical By control system
Voltage type Direct current
Nominal voltage Un V 24 ±10%
Power consumption W 2.5
Mass/ground Minuspol
Electrical protection IP IP65 (applise only to the electrically part)
– Input clamps IP IP20
– Input plug IP IP65
Connection
– Multipole Connector 25-pin sub-D connector or 24-pin industrial connector
– Sensor inputs Ladder clamps or M8 x 14-pin connectors
Status indication LED
Protective circuit Integrated
(1
other numbers of valves can be fitted via the use of blanking plates.
(2
Version “middle position vented“ 1000 l/min

88
Multipole Island with sub-D-multipole connector 25pole (or heavy industrial connector) and
16 M8 4-pin feedback inputs with 44pin sub-D connector Valve Islands
with
Multipole
Feedback inputs with
either M8 4-pin connectors Sub-D connector Version with
sub-D-multipole connector
Connection
or clamp connections 44pole
25pole Series IM20


Version with  G1/8

heavy industrial
connector
Multipole islands can be equip-
 
ped with following valves.




– 5/2 Way Valves with


springreturn
– 5/2 Way Impulse Valves

– 5/3 Way Valves
with spring return
















to middle position


– middle position closed




       

– middle position exhausted







       
– middle position pressurized
       
  Versions:
 – Connection


with sub-D connector

  
– Connection with heavy
   industrial connector

– With or without sensor
inputs
– With multi-connection for
sensor inputs (via 44pole
sub-D connector)

Dimension Table (mm) Accessories See page 92

– Cable
Valve Islands Dimension
with sub-D plug
A A1 A2 B B1 B2 B3 B4 B5 B6 B7 C1 – Heavy industrial connector
– Straight plug M8 4pole
IM20-1/8 17 30 6 43 99 166 62.5 132 20.5 42.5 60 11
+ x C3 + x C3

Valve Islands Dimension Connection

with sub-D connector
C2 C3 D1 ØD2 ØD3 F F1 H2 H3 H4 H5
IM20-1/8 26 23 G1/4 19x0.2 5.5 40 126 68 12 9 25
x C3= Dimension C3 multiplied with number of valves

Connection with heavy

industrial connector

For order instructions see page 91, 135

Dimensions in mm

89
Valve Islands Multipole Island with 25-pin sub-D connector (or heavy duty industrial connector)
and 16 M8 4-pin feedback inputs with 44-pin sub-D connector
with
Multipole Feedback inputs with
44-pin sub-D Version with
Connection either M8 4-pin connectors
or clamp connections
connector 25-pin sub-D connector

Series IM20 Version with

heavy duty



industrial
G1/4 connector

 


Multipole islands can be equip- 

ped with following valves:


– 5/2 Way Valves with
spring return 
– 5/2 Way Impulse Valves
– 5/3 Way Valves        

with spring return        






to middle position        


– middle position closed





– middle position exhausted        

– middle position pressurized        

 
Versions: 


– Connection
with sub-D connector   

– Connection with heavy duty   

industrial connector 

– With or without sensor

inputs
– With multi-connection for
sensor inputs (via 44-pin
sub-D connector)

Accessories See page 92 Dimension Table (mm)

– Cable
Valve Islands Dimension
with sub-D plug
– Heavy duty industrial A A1 A2 B B1 B2 B3 B4 B5 B6 B7 C1
connector IM20-1/4 17 30 6 50 123 190 62.5 132 24 42.5 73.5 12
– Straight M8 4-pin connector + x C3 + x C3

Connection Valve Islands Dimension

with sub-D connector
C2 C3 D1 ØD2 ØD3 F F1 H2 H3 H4 H5
IM20-1/4 31 33 G3/8 23x0.5 6.2 40 126 86 18.5 12 31
x C3= Dimension C3 multiplied by number of valves

Connection with heavy

duty industrial connector

For order instructions see page 91, 135

Dimensions in mm

90
 Order Instructions – Valve Islands
Example: 
















Valve Islands with Multipole Connector,        

M8 assembled with:
1 item 5/2 Way Valves S9 581-1/8        

7 item 5/2 Way Valves S9 581RF-1/8        



Input module
Ident-No. Valve position

Flow divider
connection

Number of

of channel
Electrical

Position

divider
inputs
Valves
1 2 3 4 5 6 7 8 9 10 11 12
Example P A 1 0 3 8 1 D S 0 8 M M M M M M M J
04 06 08 10 12
even number of valve positions only
For order, please use the Important: Please specify the code for
neutral order form on the desired valve types
page 135
Input Modules
K Pins IP20
Valve Islands – Sizes S M8 IP65 connector
PA Type: IM20-1/8 04-08-12 Number of inputs
10381 Connections: 16-20-24
G1/8: valve outlets 28-32
G1/4: base plate
PA12867 Type: IM20-1/4 Dual Pressure Operating
Connections:
J with channel
G1/4: valve outlets
divider in port 1
G3/8: base plate
01 – 11 Position of channel
divider to valve
Electrical Connection position
Multipol-Version
DS with sub-D-Connection Ordering Code for Valves and Cover Plates
HI with industrial con- Code Symbol Description
nector A – Cover plate on valve
M 14
4 2
12
5/3 Way Solenoid Valve,
permanent signal with spring
Valves return Type: S9 581RF-..
5 13
04 to 4 valves
06 5 and 6 valves J 14
4 2
12
5/3 Way Solenoid Valve,
Impulse version
08 7 and 8 valves Type: S9 581RF-..
513
10 9 and 10 valves
G 4 2 5/3 Way Solenoid Valve,
12 11 and 12 valves 14 12 spring return to middle position,
middle position closed
14 13 and 14 valves 51 3 Type: S9 581RFG-..
16 15 and 16 valves B 4 2 5/3 Way Solenoid Valve,
14 12
spring return to middle position,
middle position pressurized
513
Type: S9 581RFB-..
E 4 2 5/3 Way Solenoid Valve,
14 12 spring return to middle position,
middle position exhausted
513 Type: S9 581RFE-..

91
Accessories for Cable with sub-D plug
Number of Cable length Order Instructions Figure
Valve Islands poles Type Order No.
IM20 25 1.0 m GSK-25-1 KL9012
25 3.0 m GSK-25-3 KL9013
with Multipole 25 5.0 m GSK-25-5 KL9014
Connector 44 5.0 m GSK-44-5 KL9005

– Cable with sub-D plug Heavy duty industrial connector with cable
– Heavy duty industrial
connector Number Cable length Order Instructions Figure
– Straight plug M8 4pole of poles Type Order No.
24 5.0 m K-IST-24 KL9003

Straight plug M8 for inputs

Number of Use Order Instructions Figure
poles Type Order No.
4 for own K-M8-4 KL9011
packing

92
Contents P- and RPS-
Version Connection Page
Supply
Dimension Table Order Instructions
P-Manifolds G1/8 92 92 Manifolds
G1/4 93 93
G1/2 94 94
for directional valves
RPS-Manifolds G1/8 95 95 S9-G1/8
G1/4 95 95 S9-G1/4

93
P-Supply P-Supply Manifold with short mounting brackets Type: PLK-1/8-..

Manifold 21 23
A

23

Series
PLK, PL
11

for directional valves

Series S9-G1/8

109

86

25
G1/4

P-supply manifolds reduce

32

and simplify tubing. They

4

allow a clear, space-saving ø6,5 30 18

design. 13 10 20

3/2, 5/2 and 5/3 Way Valves B 40

with different types of actuati-
on can be mounted in groups
Drawing shows: PLK-1/8-3
of 2-10.
Die Usage of Magnet-Impulse
Valves is possible only with
P-Manifold Type PL-...
The delivery includes:
P-Manifold
Mounting bracket
Mounting Screws
O-Rings P-Manifold with long mounting brackets Type: PL-1/8-..

95,5

Material
Description Material
P-Manifold Al anodized
Mounting Steel
A
bracket passivated
21 23 23
Galvanized 11 25
Screws
steel M3
ca. 160

O-Ring NBR
G1/4

18

16,6
59,5

ø6,5
4

13 30 10 20

B 40

Drawing shows: PL-1/8-3

Overview for directional valves see page 70-77

Dimensions in mm

94
Dimension Table (mm)
Type Number of Valves A B
PLK-1/8-2 2 65 79
PL-1/8-2 2 65 79
PLK-1/8-3 3 88 102
PL-1/8-3 3 88 102
PLK-1/8-4 4 111 125
PL-1/8-4 4 111 125
PLK-1/8-5 5 134 148
PL-1/8-5 5 134 148
PLK-1/8-6 6 157 171
PL-1/8-6 6 157 171
PLK-1/8-7 7 180 194
PL-1/8-7 7 180 194
PLK-1/8-8 8 203 217
PL-1/8-8 8 203 217
PLK-1/8-9 9 226 240
PL-1/8-9 9 226 240
PLK-1/8-10 10 249 263
PL-1/8-10 10 249 263

Order Instructions and Weight Accessories

Order In- Number Consisting of Weight Description Order No.
Type Order No. of Valves Manifold Bracket Screws O-Ring (kg) Cover plate PD 34694
PLK-1/8-2 PD 37174-0002 2 1 2 4 2 0.28 completely
PL-1/8-2 PD 32763-0002 2 1 2 4 2 0.28 Flow divider PD 42483
PLK-1/8-3 PD 37174-0003 3 1 2 6 3 0.31
PL-1/8-3 PD 32763-0003 3 1 2 6 3 0.31
PLK-1/8-4 PD 37174-0004 4 1 2 8 4 0.34
PL-1/8-4 PD 32763-0004 4 1 2 8 4 0.34
PLK-1/8-5 PD 37174-0005 5 1 2 10 5 0.37
PL-1/8-5 PD 32763-0005 5 1 2 10 5 0.37
PLK-1/8-6 PD 37174-0006 6 1 2 12 6 0.40
PL-1/8-6 PD 32763-0006 6 1 2 12 6 0.40
PLK-1/8-7 PD 37174-0007 7 1 2 14 7 0.43
PL-1/8-7 PD 32763-0007 7 1 2 14 7 0.43
PLK-1/8-8 PD 37174-0008 8 1 2 16 8 0.47
PL-1/8-8 PD 32763-0008 8 1 2 16 8 0.47
PLK-1/8-9 PD 37174-0009 9 1 2 18 9 0.50
PL-1/8-9 PD 32763-0009 9 1 2 18 9 0.50
PLK-1/8-10 PD 37174-0010 10 1 2 20 10 0.53
PL-1/8-10 PD 32763-0010 10 1 2 20 10 0.53

95
P-Supply P-Manifold with short mounting brackets Type: PLK-1/4-..

Manifolds  




Series
PLK, PL 

for directional valves



Series S9-G1/4





P-supply manifolds reduce



and simplify tubing. They ∅   

allow a clear, space-saving  
design. 

3/2, 5/2 and 5/3 Way Valves

with different types of actuati-
on can be mounted in groups Drawing shows: PLK-1/4-3
of 2-10 item.
Die Usage of Magnet-Impulse
Valves is possible only with
P-Manifold Type PL-...

The delivery includes:

P-Manifold
Mounting bracket
Mounting Screws P-Manifold with long mounting brackets Type: PL-1/4-..
O-Rings


Material
Description Material
P-Manifold Al anodized
Mounting Steel passi-
bracket vated
Galvanized   
Screws
steel  


O-Ring NBR











   

 

Drawing shows: PL-1/4-3

Overview for directional valves see page 70-77

Dimensions in mm

96
Dimension Table (mm)
Type Number of valves A B
PLK-1/4-2 2 89 99
PL-1/4-2 2 89 99
PLK-1/4-3 3 122 132
PL-1/4-3 3 122 132
PLK-1/4-4 4 155 165
PL-1/4-4 4 155 165
PLK-1/4-5 5 188 198
PL-1/4-5 5 188 198
PLK-1/4-6 6 221 231
PL-1/4-6 6 221 231
PLK-1/4-7 7 254 264
PL-1/4-7 7 254 264
PLK-1/4-8 8 287 297
PL-1/4-8 8 287 297
PLK-1/4-9 9 320 330
PL-1/4-9 9 320 330
PLK-1/4-10 10 353 363
PL-1/4-10 10 353 363

Order Instructions and Weight Accessories

Order data Number Consisting of Weight Description Order No.
Type Order No. of valves Manifold Bracket Ccrews O-Ring (kg) Cover plate
PD 34695
PLK-1/4-2 PD 37175-0002 2 1 2 4 2 0.31 completely
PL-1/4-2 PD 32765-0002 2 1 2 4 2 0.31 Flow divider PD 42516
PLK-1/4-3 PD 37175-0003 3 1 2 6 3 0.35
PL-1/4-3 PD 32765-0003 3 1 2 6 3 0.35
PLK-1/4-4 PD 37175-0004 4 1 2 8 4 0.39
PL-1/4-4 PD 32765-0004 4 1 2 8 4 0.39
PLK-1/4-5 PD 37175-0005 5 1 2 10 5 0.43
PL-1/4-5 PD 32765-0005 5 1 2 10 5 0.43
PLK-1/4-6 PD 37175-0006 6 1 2 12 6 0.47
PL-1/4-6 PD 32765-0006 6 1 2 12 6 0.47
PLK-1/4-7 PD 37174-0007 7 1 2 14 7 0.51
PL-1/4-7 PD 32765-0007 7 1 2 14 7 0.51
PLK-1/4-8 PD 37175-0008 8 1 2 16 8 0.55
PL-1/4-8 PD 32765-0008 8 1 2 16 8 0.55
PLK-1/8-9 PD 37175-0009 9 1 2 18 9 0.59
PL-1/4-9 PD 32765-0009 9 1 2 18 9 0.59
PLK-1/4-10 PD 37175-0010 10 1 2 20 10 0.63
PL-1/4-10 PD 32765-0010 10 1 2 20 10 0.63

97
P-Manifolds P-Manifold with short mounting brackets – Type: PL-1/2-..

Series PL 

  

for way valves

Series S9-G1/2

P-supply manifolds reduce
and simplify tubing. They




allow a clear, space-saving


design.


3/2, 5/2 and 5/3 Way Valves



with different types of actuati-

on can be mounted in groups


∅  
of 2-4 item.
  

The delivery includes:  

P-Manifold
Mounting bracket
Mounting Screws Drawing shows: PL-1/2-3
O-Rings

Material Dimension Table (mm)

Description Material Type Number of valves A B
P-Manifold Al anodized PL-1/2-2 2 102 122
Mounting Steel PL-1/2-3 3 143 163
bracket chromanized PL-1/2-4 4 184 204
Galvanized
Screws
steel
O-Ring NBR

Accessories Order Instructions and Weight

Description Order No. Order data Number consisting of Weight
Cover plate PD 39138 of valves (kg)
Type Order No. Manifold Mounting bracket Screws O-Ring
completely
PL-1/2-2 PD 39016-0002 2 1 2 4 2 0.45
PL-1/2-3 PD 39016-0003 3 1 2 6 3 0.60
PL-1/2-4 PD 39016-0004 4 1 2 8 4 0.80

Overview for directional valves see page 70-77

Dimensions in mm

98
RPS-manifold – Type: RPSL-S9-1/8-.
Dimension A and B see Tabelle RPS-Manifolds

Series RPSL

  




for directional valves
 Series S9-G1/8
RPS-supply manifolds reduce
and simplify tubing. They





allow a clear, space-saving
design.

The RPS manifolds have



a common compressed air
 supply (P) and common vent
lines (R,S).
Valves can be mounted in

groups of 2-10.
 
– RPS-Manifolds for more

valves on request

The delivery includes:

RPS-suppply manifold
Drawing shows: RPSL-S9-1/8-3 Mounting Screws
O-Rings

Dimension Table (mm) Material

Type Number of valves A B Description Material
RPSL-S9-1/8-2 2 75 63 P-Manifold Al anodized
RPSL-S9-1/8-3 3 98 86 Screws Galvanized
RPSL-S9-1/8-4 4 121 109 steel
RPSL-S9-1/8-5 5 144 132 O-Ring NBR
RPSL-S9-1/8-6 6 167 155
RPSL-S9-1/8-7 7 190 178
RPSL-S9-1/8-8 8 213 201
RPSL-S9-1/8-9 9 236 224
RPSL-S9-1/8-10 10 259 247

Order Instructions and Weight Accessories

Order data Number of consisting of Weight Description Order No.
Type Order No. valves Manifold Screws O-Ring (kg) Cover strip PD 32956
completely
RPSL-S9-1/8-2 PD 44813-0002 2 1 4 6 0.470
G1/8
RPSL-S9-1/8-3 PD 44813-0003 3 1 6 9 0.570 Flow divider PD 42483
RPSL-S9-1/8-4 PD 44813-0004 4 1 8 12 0.670 G1/8
RPSL-S9-1/8-5 PD 44813-0005 5 1 10 15 0.770
RPSL-S9-1/8-6 PD 44813-0006 6 1 12 18 0.870
RPSL-S9-1/8-7 PD 44813-0007 7 1 14 21 0.970
RPSL-S9-1/8-8 PD 44813-0008 8 1 16 24 1.070
RPSL-S9-1/8-9 PD 44813-0009 9 1 18 27 1.170
RPSL-S9-1/8-10 PD 44813-0010 10 1 20 30 1.270

99
RPS-Manifolds RPS-Supply Manifold – Type: RPSL-S9-1/4-..

Series RPSL Dimension A and B see Tabelle




  

for directional valves 





Series S9-G1/4 

RPS-Supply manifolds reduce

and simplify tubing. They





allow a clear, space-saving
design.





The RPS manifolds have
a common compressed air 
supply (P) and common vent
lines (R,S).

Valves can be mounted in
groups of 2-10.  
– RPS-Manifolds for more 

valves on request

The delivery includes: Drawing shows: RPSL-S9-1/4-3

RPS-supply manifold
Mounting screws
O-Rings Dimension Table (mm)
Type Number of valves A B
RPSL-S9-1/4-2 2 95 83
RPSL-S9-1/4-3 3 128 116
RPSL-S9-1/4-4 4 161 149
RPSL-S9-1/4-5 5 194 182
Material
RPSL-S9-1/4-6 6 227 215
Description Material
RPSL-S9-1/4-7 7 260 248
P-Manifold Al anodized
RPSL-S9-1/4-8 8 293 281
Screws Galvanized
steel RPSL-S9-1/4-9 9 326 314
O-Ring NBR RPSL-S9-1/4-10 10 359 347

Accessories Order Instructions and Weight

Description Order No. Order data Number of consisting of Weight
Cover strip PD 32957 Type Order No. valves Manifold Screws O-Ring (kg)
completely
G1/4 RPSL-S9-1/4-2 PD 44814-0002 2 1 4 6 0.845
Flow divider PD 42483 RPSL-S9-1/4-3 PD 44814-0003 3 1 6 9 1.045
G1/4 RPSL-S9-1/4-4 PD 44814-0004 4 1 8 12 1.245
RPSL-S9-1/4-5 PD 44814-0005 5 1 10 15 1.445
RPSL-S9-1/4-6 PD 44814-0006 6 1 12 18 1.645
RPSL-S9-1/4-7 PD 44814-0007 7 1 14 21 1.845
RPSL-S9-1/4-8 PD 44814-0008 8 1 16 24 2.045
RPSL-S9-1/4-9 PD 44814-0009 9 1 18 27 2.245
RPSL-S9-1/4-10 PD 44814-0010 10 1 20 30 2.445

Overview for directional valves see page 70-77

Dimensions in mm

100
Contents
Special Valves
Version Actuation Port size Page
Characteri- Dimensions Order Connection size
stics Instructions G1/8 to G2
Overview
3/2, 5/2 and 5/3 Way Electrical G1/8 102, 103 104-106 107
Valves with NAMUR- G1/4
connections
Series S9
5/2 Way Valves for Two Hand G1/8 108, 109 109 110
Hand Operation G1/4
Series S9
Time Delay Valve for Pneumatic G1/8 108, 109 110 110
2-Hand Safety Start Valve (Timer)
5/2 Way Oscillating Valves, Pneumatic G1/4 111 111 112
Series S9
3/2 and 5/2 Way- Pedal G1/4 113 113 114
Pedal actuated valve,
Series F
2/2 Way Stop Valve Pneumatic G1/2 115 116 116
Series ARKV G3/4
G1
G11/2
G2

101
Way Valves Series S9 – G1/8, G1/4 NAMUR
Characteristics Symbol Unit Series S9
with NAMUR G1/8 G1/4
Connections Actuation Electrically actuated Electrically actuated
General Features
Characteristics Type Spoolvalve Spoolvalve
for Standard Valves Mounting 2 Screws M5 2 Screws M6
Tube connection Thread/NAMUR Thread/NAMUR
connections connections
Thread G1/8 – 7,4 deep G1/4 – 11 deep
Weight kg 0.245 0.600
permanent signal version permanent signal version
kg 0.340 0.700
impulse version impulse version
Installation In any position In any position
Ambient temperature Tmin. / max. °C -10 to +60 -10 to +60
range (1
Medium temperature Tmin. / max. °C -10 to +60 -10 to +60
range (1
Medium Filtered compressed air
Lubrication With or without oil mist lubrication
(We recommend the use of mineral oil type
VG 32 to ISO 3448)
Pneumatic Characteristics
Nominal pressure pmin. / max. bar 6
Operating pressure range
– permanent signal pmin. / max. bar 2–10
version
– impulse version pmin. / max. bar 1.5–10
Nominal flow QN l/min 500 1300 (3
Actuation
Electrical Pilot operated
Voltage type Alternating current Direct current
(1 Note : (50/60Hz)
Please consult us for opera- Nominal voltage
ting temperatures below 0° C
– Standard version Un V 230 ±10% 24 ±10% other voltages
(2 Low wattage version on request
connector DIN EN – Low wattage version Un V 230 ±10% 24 ±10% other voltages
175301-803 form A on request
(3 Version “middle position Initial power consumption
vented“ 1000 l/min
– Standard version VA (W) 8.5 2.5
– Low wattage version VA (W) 6.6 2.1
Continuous consumption
– Standard version VA (W) 6.0 2.5
– Low wattage version VA (W) 3.9 2.1
Duty cycle ED % 100
Electrical protection IP IP 65 to DIN 40050
(applise only to solenoid with connector)
Connection Plug to DIN EN 175301-803
form B – industrial standard (2

102
Series S9 – G1/8, G1/4 NAMUR
Characteristics Symbol Unit Series S9
Way Valves
G1/8 G1/4 with NAMUR
Actuation
General Features
Electrically actuated Electrically actuated
Connections
Type Spool valve Spool valve
Mounting 2 Screws M5 2 Screws M6 Characteristics for
Tube connection Thread/NAMUR Thread/NAMUR Valves in EX Areas
connections connections
Weight kg 0.245 0.600
permanent signal version permanent signal version
0.340 0.700
impulse version impulse version
Installation In any position In any position
Ambient temperature Tmin. / max. °C -10 to +60 -10 to +60
range (1
Medium temperature Tmin. / max. °C -10 to +60 -10 to +60
range (1
Medium Filtered, unlibricated compressed air – free from
water and dirt to ISO 8573-1
Solids: Class 7 particle < 40µm for gas
Water content: pressure dew point +3°C, Class 4,
but at least 5 °C below minimum operating tempe-
rature
Pneumatic Characteristics
Nominal pressure pmin. / max. bar 6
Operating pressure range
– permanent signal version pmin. / max. bar 2–8
– impulse version pmin. / max. bar 1.5–8
Nominal flow QN l/min 500 1300 (3
Actuation
Electrical Pilot operated
Certification EC Type Test Certificate for single valve:
not required for mechanical units
EC Type Test Certificate for solenoid coil: PTB-No.
03 Ex IEC 2019X and PTB 03 ATEX 2018X to T5
Category, Single valve: II 2G c T4 T135°C (1 Note : Please consult us for
type of ignition -10°C≤Ta≤+60°C operating temperatures
protection Solenoid/individual use: below 0° C
II 2G EEx m II T5 -20°C≤Ta≤+50°C (2 Maximum power if warmed
Solenoid/manifold mounting: up to thermal load limit
II 2G EEx m II T5 -20°C≤Ta≤+40°C (3 Version “middle position
Voltage type Alternating current Direct current vented“ 1000 l/min
(50/60Hz)
Nominal voltage Un V 230 ±10% 24 ±10%
110 ±10% other voltages on request
24 ±10%
Max. switching frequency Hz 1
Connection G1/8, G1/4 G1/8, G1/4
Power rating at UN VA 3.1 (230V) 3.3 (24V)
(W) 3.0 (110V)
2.5 (24V)
Max. power at UN (2 VA 2.9 (230V) 3.0 (24V)
(W) 2.8 (110V)
2.4 (24V)
Electrical protection IP IP65 (applise only to solenoid with cable)
Connection Cable – cable lengths see Order Instructions

103
3/2 Way Valves Electrically actuated – Type: S9 381RF-1/4-NC SO

Series S9  

  

G1/4

Actuation systems:
– Electrical pilot operated

Versions: 

– With NAMUR connections




– Version to ATEX Standard 




 









 







  

5,5 x 3 flat


mounting dimensions
to NAMUR standard 



* Manual override
** Solenoid width = 30 mm on low wattage coil version

Solenoid for use in EX areas

Dimensions

Solenoid width 30 mm Cable lenth

see Order Instructions







X = 15,5 mm
The delivery includes:
1 Valve
2 Mounting Screws
1 Coding pin For more information on valves to ATEX standards
2 O-Rings see page 46, 47, 107

Overview see page 107

Dimensions in mm

104
Electrically actuated – Type: S9 581..-1/8 SO
5/2 Way Valves
Series S9
G1/8, G1/4
10,5 *
M5

Actuation systems:

ca. 140
14
33,5 – Electrical pilot operated

128
19,5
2
5,
22

28

5
ca. 208

4 Versions:
87,5
18
12

– With NAMUR connections

24

1
16

– Version to ATEX standard

18
3

2
G1/8

3
4
5,5 x 3

32
flat

15,5

12
mounting
dimensions
to NAMUR standard
*
56

* Manual override
** Solenoid width = 30 mm
15,5
only for type on low wattage coil
40
S9 581-1/8SO 22** version
63

Electrically actuated – Type: S9 581..-1/4 SO Solenoid for use in EX areas

Dimensions
32

**
22

Cable length
see Order Instructions
Solenoid width 30 mm


*
M5

10



14

41

ca. 159
ca. 231



9
3
5,5 x 3

32,7
30,5

148

5,2 5
flat

4
22

106
12

20,7

1

G1/4
24

 The delivery includes:

22

2 X = 15,5 mm
19,5
3
1 Valve
mounting
32 For more information on 2 Mounting Screws
dimensions 21
12
valves to ATEX standards 1 Coding pin
to NAMUR standard
see page 46, 47, 107 2 O-Rings
20

*
62

only for type

S9 581-1/4SO
* Manual override
15,5 ** Solenoid width = 30 mm
52
on low wattage coil
63
version

Overview see page 107

Dimensions in mm

105
5/3 Way Valves Electrically actuated – Type: S9 581RF.-1/8-NC SO

Series S9
G1/8, G1/4







 



Actuation systems: 





– Electrical pilot operated



 










Versions:







– With NAMUR connections
5,5 x 3 flat


– Version to ATEX Standard 
mounting 


dimensions
to NAMUR 
standard


* Manual override
** Solenoid width = 30 mm
on low wattage coil

version

 


Electrically actuated – Type: S9 581RF.-1/4-NC SO

Solenoid for use in EX areas
Dimensions

Cable length


see
Solenoid width 30 mm Order Instructions



 





5,5 x 3 flat







 





















The delivery includes:



1 Ventil mounting 

dimensions to  
2 Mounting Screws


NAMUR standard
1 Coding pin
2 O-Rings For more information on


valves to ATEX standards

see page 46, 47, 107


* Manual override


** Solenoid width = 30 mm
  on low wattage coil
version

Overview see page 107

Dimensions in mm

106
Order Instructions – 3/2, 5/2 and 5/3 Way Valves – with NAMUR connections
Actuation System Symbol Order Instructions Page
Type Order No.
Electrical, 2
12 10
permanent signal S9 381RF-1/4NG SO-.. PD 33854-..33 104
1 3

Electrical, 4 2
S9 581RF-1/8 SO-.. PD 34143-..33 105
permanent signal 14 12
S9 581RF-1/4 SO-.. PD 34985-..33 105
5 13

Electrical, 4 2 S9 581-1/8 SO-.. PD 34984-..33 105

14 12
impulse S9 581-1/4 SO-.. PD 34986-..33 105
513

Electrical, 4 2 S9 581RFG-1/8 SO-.. PD 40813-..33 106

permanent signal 14 12
S9 581RFG-1/4 SO-.. PD 40808-..33 106
spring return
51 3
to middle position
4 2 S9 581RFE-1/8 SO-.. PD 40814-..33 106
14 12
S9 581RFE-1/4 SO-.. PD 40618-..33 106
513

4 2 S9 581RFB-1/8 SO-.. PD 40815-..33 106

14 12
S9 581RFB-1/4 SO-.. PD 40809-..33 106
513

Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Standard version 230V 50/60Hz 110 V = 61 –
24V = 60V 50/60Hz 02 –
Low wattage version 24V = 13 –
230V 50/60Hz 69 –
EX Area versions to ATEX Standard
Category, type of ignition protection
Single valve: II 2G c T4 T135°C -10°C≤Ta≤+60°C
Solenoid/individual use: II 2G EEx m II T5 -20°C≤Ta≤+50°C
Solenoid/manifold mounting: II 2G EEx m II T5 -20°C≤Ta≤+40°C
Solenoid version Nominal voltage Applicable for Key code ATEX Type additon
Solenoid 24V = 48 Atex
– with cable 1.2 m
– with cable 3 m 24V = 45 Atex
– with cable 5 m 24V = 46 Atex
– with cable 10 m 24V = 47 Atex
– with cable 1.2 m 24V 50/60Hz 99 Atex
– with cable 1.2 m 110V 50/60Hz 97 Atex
– with cable 1.2 m 230V 50/60Hz 98 Atex
Example for valves in ATEX-Version:
– for valves Series S9-G1/8, S9-G1/4, S9-G1/2
Please add behind the standard order No. “ATEX“
Type: S9 581RFG-1/8SO-4633
Order No. PA34143-4633ATEX

107
5/2 Way Valve Characteristics – Pneumatically actuated with 2 hand operation and Time Delay Valve
Characteristics Symbol Unit Description
Series S9 Version Two Hand Operation Time Delay
Valve
G1/8, G1/4 Type S9 563/65RF- S9 563/65RF- S9 361RF-
1/8-SO 1/4-SO 1/8-SO
Actuation System: General Features
– Pneumatic Type Spool valve Spool valve Spool valve
for two hand operation
Mounting 2 Screws M5 2 Screws M6 2 Screws M5
2 hand operated valve for
pneumatically controlled ma- Tube connection Thread Thread Thread
chines and equipment. Port size G1/8 G1/4 (12.1 and G1/8
The 2-handed trip valves 12.2: G1/8)
PD37173 and PD37673 are Weight (mass) kg 0.27 0.64 0.18
classed as category 1 in accor-
Installation In any position
dance with
DIN EN 954-1 Ambient temperature Tmin/max °C -10 to +60 **
(only in connection with sui- range
table push button valves) and Medium temperature Tmin/max °C -10 to +60 **
type IIIA in accordance with range
DIN EN 574.
Medium Filtered compressed air - free from water and dirt to
ISO 13851: ISO 8573-1
Safety of machines; two-han- Solids: Class 6 particle <5µm for Gas
ded controls. gaswater content: pressure dew point +3°C, Class 4,
but at least 5°C less than min. operating temperature
ISO 13849-1: Lubrication * none or oil mist lubrication
Safety of machines; safety-
related parts of control Pneumatic Characteristics
systems. Nominal pressure pn bar 6
Area of application: Operating pressure range pmin/max bar 0 – 10 2-10
The 2-handed safety valves Nominal flow QN l/min 500 1300 450
are intended to be used where
persons carry out manual Actuation
control functions in areas that Pneumatic Direct
are subject to accident risks.
These comprise primarily Actuation pressure range pst min/max 2 – 10 3 – 10 2-10
equipment with pneumatic * We recommend the use of mineral oil type VG 32 to ISO 3448
cylinders, the operation of ** Note: Please consult us for operating temperatures below 0° C
which requires that both
hands are kept away from the
danger zone. The valves can Function: Fitting Instructions:
also be used to prevent unin- The valve only switches from If due to mechanical stopping We recommend the following
outlet port 4 to outlet port 2 and re-opening of the compressed time-delay valve from our range:
tended starts of pneumatic
if both signal inlets are si- air supply both control buttons type PD49078.
processes.
multaneously actuated or are are operated or possibly blocked As push button valve we recom-
actuated within 0.5 s. at the same time, the 2-handed mend the basic valve PA10307
When the operator releases trip valve will continue the control for control panel configuration,
one or both control buttons, function. The 2-handed trip in combination with push button
the valve switches back valve is not suited to prevent the KX9357.
immediately. switching from port 4 to port 2
upon the compressed air being Characteristics of time-delay
In order to resume the switch switched back on after it was shut valve see table above.
function, both trip signals off and/or permanently operated
have to be cancelled first. control buttons.
In order to prevent this process
Note: from happening, we advise users
Not applicable for operating that it is necessary to install a
eccentric presses and presses time-delay valve in the supply
of similar design. line of one of the control buttons
(line 12.1 or 12.2).
Dimensions in mm

108
Safety switch diagram (example) In order to comply with
Usage of 2-hand-operation valve with cecessary time delay valve safety requirements, plant
and equipment with certain
operating mechanisms require
the installation of a time-
delay valve in the pneumatic
control system, as shown in
the example.
  

2-handed trip valve 

  
Type: S9563/65-1/8-SO PD37673
Type: S9563/65-1/4-SO PD37173 

  

Pressure Control Valve, comprising  

   
of basic valve and activity part
Basic valve: Type S9 390RF-1/8 PA10307
Pushbutton, red: Type KX9357    


 
Time delay valve

Type S9361RF-1/8-SO PD49078
 




 

Pneumatically actuated by 2-handed trip valve

Type: S9 563/65RF-1/8-SO Type: S9 563/65RF-1/4-SO













 




 































 




 









 

 
 

 



Dimensions in mm

109
 Time-delay valve to 2-handed trip valve
Type: S9 361RF-1/8-SO


























Note:
Suitable measures must be 
taken to protect the valves   
against ingress of dust and 
water. 

Order Instructions
Actuation System Symbol Order Instructions
Type Order No.
pneumatic, 4 2
S9 563/65RF-1/8-SO PD37673
by 2-hand tripping
12.1

≥1 t &

S9 563/65RF-1/4-SO PD37173
12.2

5 1 3

Time Delay Valve  S9 361RF-1/8-SO PD49078

for 2-Hand-safety related
 
control 

 

110
Characteristics
5/2-Way
Characteristics Symbol Unit Description
General Features Oscillating
Type Spool valve Valves
Mounting
Tube connection
2 Screws M6 (M4)
Thread
Series S9
Connection size G1/4, 11 deep
G1/4
Weight (mass) kg 0.65
Installation In any position Actuation System:
Ambient temperature Tmin/max °C -10 to +60 – Pneumatic
range **
Medium Tmin/max °C -10 to +60 The oscillating valve generates
temperature range ** oscillating movements such
as e.g. shaking, hammering,
Medium Filtered and oiled or plunging, feed motions etc.
filtered, unoiled compressed air
Lubrication * None or oil mist lubrication Function:
Pneumatic Characteristics If compressed air is intro-
ducesed into inlet port 1,
Nominal pressure pn bar 6 the outlet ports 4 and 2 are
Operating pressure range pmin/max bar 3–8 alternately supplied with
compressed air.
Nominal flow QN l/min 1300
The speed of the operated
Actuation cylinder and also the stroke
Pneumatic Direct frequency are adjusted with
two exhaust air throttles.
Actuation pressure range pst min/max 3–8
* We recommend the use of mineral oil type VG 32 to ISO 3448
** Note: Please consult us for operating temperatures below 0° C

Pneumatic oscillating – Type: S9 568/68-1/4-SO



 






 






































Dimensions in mm

111
Order Instructions
Actuation System Symbol Order Instructions
Type Order No.
Pneumatic   S9 568/68-1/4-SO PD 34796

 

  

Dimensions in mm

112
Characteristics
3/2 and
Characteristics Symbol Unit Description
General Features 5/2 Way Valves
Type Poppet Valve Pedal actuated
Mounting
Tube connection
4 Screws M8 (1
Thread
Series F
Port size G1/4
G1/4
Weight (mass) kg 1.5
Installation In any position Actuation System:
Ambient temperature Tmin/max °C -10 to +55 – Pedal
range (3
Medium temperature Tmin/max °C -10 to +60 Connections for
range (3 3/2 way version:
Medium Filtered and oiled or filtered, Version
unoiled compressed air „Normally closed“: P, B, S
„Normally open“: P, A, R
Lubrication (2 Oil mist lubrication compatible with Buna N
Pneumatic Characteristics * Only for version “both
Nominal pressure pn bar 6 switch positions indexed“
– return is only effected
Operating pressure range pmin/max bar 0 – 10 after actuating the locking
Nominal flow QN l/min 1400 pedal.
Actuation Mounting Instruction:
Manual control Direct Use only screw connections
Stroke mm 2 with max. wrench size across
flats of 15.
Actuation force Fb N ca. 30
(1 After removing the rubber footing Connection designation:
(2 We recommend the use of mineral oil type VG 32 to ISO 3448 A = 4 Outlet
(3 Note: Please consult us for operating temperatures below 0° C B = 2 Outlet
R = 5 Exhaust
P = 1 Air supply
S = 3 Exhaust

Pedal actuated – Type: F331..-08.., F531..-08

 
Actuation stroke








 




 






 


 

 





Dimensions in mm

113
Order Instructions – 3/2 and 5/2 Way Valves
Actuation Symbol Order Instructions
Type Order No.
Pedal a
B
b
F 331RF-08NG* KZ 4410
with spring return a b

P S
A F 331RF-08NO* KZ 4411
a b
a b

P R
Pedal a,b
B F 331-08NG* KZ 4408
without reset a b

P S

a,b
A F 331-08NO* KZ 4409
a b

P R
A B
Pedal a b F 531RF-08 KZ 4413
with spring return a b

R PS

Pedal a,b
A B
F 531-08 KZ 4412
both switch positions a b
indexed
RPS

* NC – Version normally closed

NO – Version normally open

Dimensions in mm

114
Characteristics
Characteristics Symbol Unit Description
2/2 Way
General Features Stop Valves
Description 2/2 Way Valve Series ARKV
Type Poppet valve normally closed
Mounting Direct in piping G1/2 to G2
Tube connection Thread
Port size G1/2 G3/4 G1 G1 1/2 G2 Actuation System:
– Pneumatic
Weight (mass) kg 0.745 1.115 1.365 2.695 4.290
Installation In any position
Ambient temperature Tmin/max °C -20 to Note: Please consult us for operating
range +80 temperatures below 0° C
Medium temperature Tmin/max °C 0 to +80
range
Medium Compressed air, neutral gases, presswater
(for low flow- und valve closingspeed only )
Actuating medium filtered compressed air
Pneumatic characteristics
Nominal pressure pn bar 6.3
Operating pressure range pmin/max bar 0 – 10
Nominal flow QN l/min 2200 5000 6900 22000 40000
Actuation
Pneumatic Direct

Actuating Pressure Actuating Pressure Actuating Pressure

– Type: ARKV-15 – Type: ARKV-20 – Type: ARKV-25
  

  
  

  

  

  

   
    
         
     
 

O = pst min to open O = pst min to open O = pst min to open

S = pst max to close S = pst max to close S = pst max to close

Actuating Pressure Actuating Pressure

– Type: ARKV-40 – Type: ARKV-50
 

 

 

 

 

 

 
   

         
 

O = pst min to open O = pst min to open

Dimensions in mm
S = pst max to close S = pst max to close

115
Pneumatically actuated – Type: ARKV-..






Dimension Table
Type A B C D E F G H
ARKV-15 NC 65 G1/2 G1/8 55 61 41.5 95 109.5
ARKV-20 NC 76 G3/4 G1/4 65 75 50 112 129
ARKV-25 NC 91 G1 G1/4 65 75 57 119 139
ARKV-40 NC 123 G11/2 G1/4 110 112 67 137 167.5
ARKV-50 NC 150 G2 G1/4 130 134 75 153 190

Order Instructions
Actuation System Symbol Order data
Type Order No.
Pneumatic ARKV-15 NC PD 07334
 ARKV-20 NC PD 07580
 
ARKV-25 NC PD 07581

ARKV-40 NC PD 07757
ARKV-50 NC PD 07765

Dimensions in mm

116
Contents
Version Actuation Standard / Page
Way Valves to
Size Characteristics Dimension Order VDMA 24563
Table Instructions
Overview and
5/2 and 5/3
Way Valves
Pneumatic
Electrical
VDMA
24563
118, 119 120 124, 125
ISO5599
Series S20 size 01
5/2 and 5/3 Pneumatic ISO 5599 118, 119 121 124, 125
Way Valves Electrical size 1 Series S20
Series S20
5/2 and 5/3 Pneumatic ISO 5599 118, 119 122 124, 125
Way Valves Electrical size 2
Series S20
5/2 and 5/3 Pneumatic ISO 5599 118, 119 123 124, 125
Way Valves Electrical size 3
Series S20

X. ..
A XD
I S OM
db y
ce
repla
i l l be
w

117
Way Valves to Characteristics
Characteristics Symbol Unit Series S20
VDMA 24563 to VDMA 01
and ISO5599 Actuation
General Features
Pneumatic Electrical

Type Ceramic-Spool valve

Series S20 Mounting Via base plate to VDMA 24563
Tube connection Base Plate
Port size G1/8 or G1/4 (base plate)
Weight
– permanent signal kg 0.130 0.170
– impulse version kg 0.130 0.210
Installation In any position In any position
Ambient temperature Tmin. / max. °C -10 to +60 -10 to +60
range (1
Medium temperature Tmin. / max. °C -10 to +55 -10 to +55
range (1
Medium Filtered compressed air
Lubrication With or without oil mist lubrication
(We recommend the use of mineral oil type
VG 32 to ISO 3448)
X. ..
Pneumatic Characteristics
A XD
Nominal pressure pmin. / max. bar 6
I S OM 6
Operating pressure range (2
d b -0.9 – 10 y
a c e
epl bar -0.9 – 10
– permanent signal version pmin. / max.
bar 2 – 10
– impulse version
be r
pmin. / max. 2 – 10

w i l l
– with external pilot air pmin. / max. bar – -0.9 – 10
Maximum flow Q max. l/min 1050 1050
Actuation
Pneumatic Direct –
Actuation pressure range
– permanent signal version pmin. / max. bar 2 – 10 2 – 10
– impulse version pmin. / max. bar 2 – 10 2 – 10
Electrical Pilot operated
Voltage type AC 50/60Hz Direct current
Nominal voltage
– Standard version Un V 230 ±10% 24 ±10%
– Low wattage version Un V – –
Initial power consumption
– Standard version VA (W) 2 2 Nominal Power
– Low wattage version VA (W) 2 2
Continuous consumption
(1 Note: – Standard version VA (W) – –
Please consult us for – Low wattage version VA (W) – –
operating temperatures Duty cycle ED % 100
below 0° C
Electrical protection IP IP65 to DIN 40050
(2 16 bar Version for
(applise only to solenoid with connector)
valves to ISO 5599
size 1, 2, 3 on request Connection Plug to
(4 Low wattage version DIN EN 175301-803 form C
connector DIN EN
175301-803 form A

118
Series S20 to ISO 5599
Size 1 Size 2 Size 3
Pneumatic Electrical Pneumatic Electrical Pneumatic Electrical

Ceramic-Spool valve
via base plate to ISO5599
Base plate
G1/4 (Base plate) G3/8 (Base plate) G1/2 (Base plate)

0.350 0.410 0.600 0.650 1.100 1.150

0.350 0.450 0.600 0.700 1.100 1.200
In any position In any position In any position In any position In any position In any position
-10 to +60 -10 to +60 -10 to +60 -10 to +60 -10 to +60 -10 to +60

-10 to +60 -10 to +60 -10 to +60 -10 to +60 -10 to +60 -10 to +60

Filtered compressed air

With or without oil mist lubrication
(We recommend the use of mineral oil type VG 32 to ISO 3448)
X. ..
A XD
6 OM
6 6 6
y I S 6 6

e–d
b
a c
epl -0.9 – 12
-0.9 – 12 2 – 12 -0.9 12 2 – 12 -0.9 – 12 2 – 12
-0.9 – 12 2 – 12
be r 2 – 12 -0.9 – 12 2 – 12
–
w i l l
-1 – 12 – -1 – 12 – -1 – 12
1680 1680 4320 4320 6540 6540

Direct – Direct – Direct –

2 – 12 2 – 10 2 – 12 2 – 10 2 – 12 2 – 10
2 – 12 2 – 10 2 – 12 2 – 10 2 – 12 2 – 10
Pilot operated
Alternating current 50/60Hz Direct current

230 ±10% 24 ±10% other voltages

230 ±10% 24 ±10% on request

11 4.8
7.8 2.7

8.5 4.8
4.9 2.7
100
IP65 to DIN 40050
(applise only to solenoid with connector)
Plug to DIN EN 175301-803 form B – industrial standard (4

119
5/2 and 5/3 Weight (mass) kg
Description Type Weight * Type supplements for
Way Valves (mass) version with middle position
G = middle position closed
Series S20 Pneumatic, by permanent signal S20 561R..-01*
Pneumatic, by impulse S20 561-01
0.130
0.130
E = middle position exhausted
B = middle position pressurized
Electrical, by permanent signal S20 581R..-01* 0.170
to VDMA 24563
Electrical, by permanent signal S20 581S-R..-01* 0.170
Size 01
Electrical, by impulse S20 581-01 0.210
Actuation systems: – with biased position S20 582-01 0.210
– Pneumatic Electrical, by impulse S20 581S-01 0.210
– Electrical pilot operated

Versions: Pneumatically actuated – Type: S20 561...-01

– With external pilot air
– With biased position  

 ..

X.
XD


A
OM


I S


db y
ce
repla
i l l be 

w
Electrical pilot operated – Type: S20 581...-01-.., S20 582...-01-.., S20 581S...-01-..
 









The delivery includes:



1 Valve with mounting screws



1 Gasket




* Manual override

Overview and order instructions see page 124, 125

Dimensions in mm

120
 Weight (mass) kg
Description Type Weight (mass) * Type supplements for
5/2 and 5/3
Pneumatic, by permanent signal S20 561R..-1* 0.350 version with middle position Way Walves
Pneumatic, by impulse S20 561-1 0.350 G = middle position closed
E = middle position exhausted
Series S20
Electrical, by permanent signal S20 581R..-1* 0.410
B = middle position pressurized
Electrical, by permanent signal S20 581S-R..-1* 0.410 to ISO 5599
Electrical, by impulse S20 581-1 0.450 size 1
– with biased position S20 582-1 0.450
Electrical, by impulse S20 581S-1 0.450 Actuation systems:
– Pneumatic
– Electrical pilot operated
Pneumatically actuated – Type: S20 561...-1

Versions:
– With external pilot air
– With biased position
– Low wattage version




X. ..


XD


A
I S OM
db y
ce
epla
be r


will
Electrical pilot operated
Type: S20 581...-1-.., S20 582-1-.., S20 581S...-1-..
Magnet for low wattage
version
 


Solenoid width = 30 mm
 







The delivery includes:



1 Valve with mounting screws



1 Gasket



* Manual override

Overview and order instructions see page 124, 125

Dimensions in mm

121
5/2 and 5/3 Weight (mass) kg
Description Type Weight * Type supplements for
Way Valves (mass) version with middle
position
Series S20 Pneumatic, by permanent signal S20 561R..-2*
Pneumatic, by impulse S20 561-2
0.600
0.600 G = middle position
Electrical, by permanent signal S20 581R..-2* 0.650 closed
to ISO 5599 E = middle position
Electrical, by permanent signal S20 581S-R..-2* 0.650
size 2 exhausted
Electrical, by impulse S20 581-2 0.700 B = middle position
pressurized
Actuation systems: – with biased position S20 582-2 0.700
– Pneumatic Electrical, by impulse S20 581S-2 0.700
– Electrical pilot operated

Versions: Pneumatically actuated – Type: S20 561...-2

– With external pilot air 

– With biased position

– Low wattage version 


X. ..


A XD


S OM


y I
ce db
er epla
i l l b 

Electrical pilotw
operated Magnet for low wattage
Type: S20 581...-2-.., S20 582-2-.., S20 581S...-2-.. version
 



Solenoid width = 30 mm


The delivery includes:






1 Valve with mounting screws



1 Gasket





* Manual override

Overview and order instructions see page 124, 125

Dimensions in mm

122
 Weight (mass) kg
Description Type Weight * Type supplements for
5/2 and 5/3
(mass) version with middle position Way Valves
Pneumatic, by permanent signal S20 561R..-3* 1.100 G = middle position
closed
Series S20
Pneumatic, by impulse S20 561-3 1.100
E = middle position
Electrical, by permanent signal S20 581R..-3* 1.150 exhausted to ISO 5599
Electrical, by permanent signal S20 581S-R..-3* 1.150 B = middle position size 3
Electrical, by impulse S20 581-3 1.200 pressurized

– with biased position S20 582-3 1.200 Actuation systems:

– Pneumatic
Electrical, by impulse S20 581S-3 1.200 – Electrical pilot operated
Pneumatically actuated – Type: S20 561...-3
 Versions:
– With external pilot air
– With biased position
– Low wattage version



X. ..


A XD


I S OM


db y
ce
er epla
i l l b
woperated


Electrical pilot – Type: S20 581...-3-.. Magnet for low wattage version
 



Solenoid width = 30 mm
 


The delivery includes:







1 valve with mounting screws

1 Gasket





* Manual override

Overview and order instructions see page 124, 125

Dimensions in mm

123
Order Instructions – 5/2 Way Valves
Actuation Symbol Standard / Size Order Instructions Page
Type Order No.
Pneumatic VDMA 24563 Gr. 01 S20 561RF-01 PA 12891 120
by permanent signal, 14
4 2
12 ISO 5599 Größe1 S20 561RF-1 PA 12869 121
spring return
513
ISO 5599 size 2 S20 561RF-2 PA 16425 122
ISO 5599 size 3 S20 561RF-3 PA 16426 123
Pneumatic VDMA 24563 Gr. 01 S20 561R-01 PA 12892 120
by permanent signal, 14
4 2
12 ISO 5599 size 1 S20 561R-1 PA 12870 121
air spring return
ISO 5599 size 2 S20 561R-2 PA 16428 122
513
ISO 5599 size 3 S20 561R-3 PA 16429 123
Pneumatic VDMA 24563 Gr. 01 S20 561-01 PA 12893 120
by impulse 14
4 2
12 ISO 5599 size 1 S20 561-1 PA 12868 121
513
ISO 5599 size 2 S20 561-2 PA 16422 122
ISO 5599 size 3 S20 561-3 PA 16423 123
Pneumatic VDMA 24563 Gr. 01 S20 562-01 PA 12908 120
by impulse 14
4 2
12 ISO 5599 size 1 S20 562-1 PA 12905 121
with biased position
513
ISO 5599 size 2 S20 562-2
..
PA 12906
X.
122
ISO 5599 size 3 S20 562-3
MA XD
PA 12907 123
Electrical VDMA 24563 Gr. 01
O
S20 581RF-01-..
IS
PA 12886-..33 120
by permanent signal,
spring return
14
4 2
12 ISO 5599 size 1
d b y
S20 581RF-1-.. PA 12875-..33 121

pla ce
ISO 5599 size 2 S20 581RF-2-.. PA 16441-..33 122
e
5 13

b e r
ISO 5599 size 3 S20 581RF-3-.. PA 16442-..33 123

will VDMA 24563 Gr. 01

with external pilot air
S20 581S-RF-01-.. PA 12896-..33 120
4 2
14 12
ISO 5599 size 1 S20 581S-RF-1-.. PA 12882-..33 121
pst 513 ISO 5599 size 2 S20 581S-RF-2-.. PA 16456-..33 122
ISO 5599 size 3 S20 581S-RF-3-.. PA 16462-..33 123
Electrical VDMA 24563 Gr. 01 S20 581R-01-.. PA 12887-..33 120
4 2
by permanent signal, 14 12
ISO 5599 size 1 S20 581R-1-.. PA 12876-..33 121
air spring return
ISO 5599 size 2 S20 581R-2-.. PA 16444-..33 122
513
ISO 5599 size 3 S20 581R-3-.. PA 16445-..33 123
Electrical VDMA 24563 Gr. 01 S20 581-01-.. PA 12888-..33 120
by impulse 14
4 2
12 ISO 5599 size 1 S20 581-1-.. PA 12874-..33 121
ISO 5599 size 2 S20 581-2-.. PA 16438-..33 122
513
ISO 5599 size 3 S20 581-3-.. PA 16439-..33 123
with external pilot air
VDMA 24563 Gr. 01 S20 581S-01-.. PA 12898-..33 120
4 2
14 12 ISO 5599 size 1 S20 581S-1-.. PA 12880-..33 121
pst 5 13 pst
ISO 5599 size 2 S20 581S-2-.. PA 16454-..33 122
ISO 5599 size 3 S20 581S-3-.. PA 16460-..33 123
Electrical VDMA 24563 Gr. 01 S20 582-01-.. PA 12904-..33 120
by impulse 14
4 2
12 ISO 5599 size 1 S20 582-1-.. PA 12901-..33 121
with biased position
5 13
ISO 5599 size 2 S20 582-2-.. PA 12902-..33 122
ISO 5599 size 3 S20 582-3-.. PA 12903-..33 123

Type and additional order instructions see page 125

124
Order Instructions – 5/3 Way Valves
Actuation Symbol Standard / Size Order Instructions Page
Type Order No.
Pneumatic VDMA 24563 Gr. 01 S20 561RFG-01 PA 12894 120
by permanent signal, 4 2
ISO 5599 size 1 S20 561RFG-1 PA 12871 121
14 12
spring return
to middle position 51 3
ISO 5599 size 2 S20 561RFG-2 PA 16431 122
ISO 5599 size 3 S20 561RFG-3 PA 16432 123

4 2
14 12 ISO 5599 size 1 S20 561RFB-1 PA 12873 121
5 13 ISO 5599 size 2 S20 561RFB-2 PA 16437 122

VDMA 24563 Gr. 01 S20 561RFE-01 PA 12895 120

4 2
14 12 ISO 5599 size 1 S20 561RFE-1 PA 12872 121

513
ISO 5599 size 2 S20 561RFE-2 PA 16434 122
ISO 5599 size 3 S20 561RFE-3 PA 16435 123
Electrical VDMA 24563 Gr. 01 S20 581RFG-01 PA 12889-..33 120
by permanent signal, 4 2
ISO 5599 size 1 S20 581RFG-1-.. PA 12877-..33 121
14 12
spring return
to middle position 51 3
ISO 5599 size 2
.. S20 581RFG-2-..
3X. S20 581RFG-3-..
PA 16447-..33 122
D
AX
ISO 5599 size PA 16448-..33 123

O M
14
4 2

by
12 IS ISO 5599 size 1 S20 581RFB-1-.. PA 12879-..33 121

a ced ISO 5599 size 2 S20 581RFB-2-.. PA 16453-..33 122

repl
513

b e
will 14
4 2
12
VDMA 24563 Gr. 01
ISO 5599 size 1
S20 581RFE-01
S20 581RFE-1-..
PA 12890-..33
PA 12878-..33
120
121
513
ISO 5599 size 2 S20 581RFE-2-.. PA 16450-..33 122
ISO 5599 size 3 S20 581RFE-3-.. PA 16451-..33 123
with external pilot air VDMA 24563 Gr. 01 S20 581S-RFG-01.. PA 12900-..33 120
4 2
12
14
ISO 5599 size 1 S20 581S-RFG-1-.. PA 12883-..33 121
pst 513 pst ISO 5599 size 2 S20 581S-RFG-2-.. PA 16457-..33 122
ISO 5599 size 3 S20 581S-RFG-3-.. PA 16463-..33 123

4 2
14 12 ISO 5599 size 1 S20 581S-RFB-1-.. PA 12885-..33 121
pst 513 pst
ISO 5599 size 2 S20 581S-RFB-2-.. PA 16459-..33 122

VDMA 24563 Gr. 01 S20 581S-RFE-01-.. PA 12899..33 120

4 2
14 12 ISO 5599 size 1 S20 581S-RFE-1-.. PA 12884..33 121

pst pst
ISO 5599 size 2 S20 581S-RFE-2-.. PA 16458..33 122
513
ISO 5599 size 3 S20 581S-RFE-3-.. PA 16464..33 123

Solenoid version Nominal voltage Applicable for Key code

Standard version 230V 50/60Hz 110 V = 61
24V = 60V 50/60Hz 02
Low wattage version 24V = 13
230V 50/60Hz 69
Other voltages on request

125
126
Contents
Version Standard / Size Page
Single Base
Dimensions Order Instructions Plates
Overview
Single Base Plates VDMA 24563 128 128 – to VDMA 24563,
G1/8, G1/4 size 01
Modules for Base Plate VDMA 24563 129 129
Size 01
Combimations size 01 – to ISO 5599
G1/8, G1/4
Size 1, 2, 3
Single Base Plates ISO 5599 130. 131 130. 131
size 1, 2, 3
Base Plate combinations ISO 5599 132, 133 132, 133
size 1, 2, 3

X. ..
A XD
I S OM
db y
ce
repla
i l l be
w

127
Single Base Single Base Plates Form A – Connection size G1/8 – Type: S20-01-1/8-A


Plates


to VDMA 24563


   

Size 01, Form A 




Port Size: 
G1/8
G1/4














 



X. ..
XD


A
I
Single Base Plates Form A – Connection size G1/4 – Type: S20-01-1/4-A
S OM
db y
ce


epla


be r
w i l l



   




















 





Order Instructions
Description Port size Weight (kg) Order Instructions
Type Order No.
Single Base Plate G1/8 0.070 S20-01-1/8-A KL8004
G1/4 0.120 S20-01-1/4-A KL8005
Dimensions in mm

128
End Plate Set Form D for Intermediate Plate
Description Size Weight Order Instructions Figure
Modules for
(kg) Type Order No. Base Plate
End Plate set
Form D
VDMA
01
0.220 S20-01-D KL8008 Combinations
to VDMA 24563
size 01

The delivery includes: End Plate set, completely with screws Modules:
– End Plate set, Form D, for
Intermediate Plate Form C
– Angle base plate, Form E,
for Intermediate Plate
Intermediate Plate Form C Form C
Description Port Weight Order Instructions Figure – Accessories
(Port size) (kg) Type Order No. Port Size:
G1/8
Intermediate VDMA 01 0.080 S20-01-C KL8006 G1/4
Plate form C (G1/8)

Intermediate VDMA 01 0.100 S20-01-C KL8007

X. ..
XD
Plate form C (G1/4)
A
I S OM
y
The delivery includes: Intermediate Plate, completely with O-Rings and screws
db
ce
er epla
Dummy plate
i l l b
Description w size Weight Order Instructions Figure
(kg)
Type Order No.
Dummy Plate VDMA 0.050 S20-01- KL8009
01 BP

The delivery includes: Dummy Plate with gasket and screws

Dimensions in mm

129
Base Plates Single Base Plates Form A – Type: S9-.-A


to ISO 5599 
Size 1, 2, 3
Versions:
– Single Base Plates


to VDMA 24345 Form A









X. ..
XD


A
OM


y I S
ce db

epla

be r
w i l l 

Dimension Table Single Base Plates Form A

ISO-Size A B C D E F G H
1 84 43 G1/4 10.5 21.5 10 32 98
2 95 56 G3/8 14 26 13 40 112
3 119 68 G1/2 17 17 18 32 136

ISO-Size J K L M N O P Q
1 48 5,5 110 10.5 23,5 24 G1/8 58
2 57 6,6 124 14 30 30 G1/8 74
3 71 6,6 149 17 22 32 G1/8 90

Order Instructions Form A

ISO-Size Weight (kg) Order Instructions
Type Order No.
1 0.160 S9-1-A KX 9076
2 0.280 S9-2-A KX 9433
3 0.570 S9-3-A KX 9434
Dimensions in mm

130
Single Base Plates Form B – Type: S9 -.-B
Base Plates

to ISO 5599

Size 1, 2, 3
Versions:
– Single Base Plates
to VDMA 24345 Form B




 








X. ..
AXD
I S OM
dby
ce
epla



be r
w i l l

Dimension Table Single Base Plates Form B

ISO-Size A B C D E F H J
1 46 110 10 30 5 84 G1/8 G1/4
2 56 124 13 35 6,5 95 G1/8 G3/8
3 71 149 18 32 9 119 G1/8 G1/2

ISO-Size K L M N O P Q
1 5,5 98 23 46 62 23 7.5
2 6,6 112 28 56 73 27 7.5
3 6,6 136 34 68 90 35 10

Order Instructions Form B

ISO-Size Weight (kg) Order Instructions
Type Order No.
1 0.370 S9-1-B KX 9077
2 0.590 S9-2-B KX 9436
3 0.900 S9-3-B KX 9437
Dimensions in mm

131
Modules for End Plate Set Form D for Intermediate Plate – Order Instructions and Weight
ISO-Size Weight (kg) Order Instructions Figure
Base Plate Type Order No.
Combinations 1 0.210 S9-1-D KX 9078

2 0.360 S9-2-D KX 9421

to ISO 5599
Size 1, 2, 3 3 0.680 S9-3-D KX 9422

Versions The delivery includes: End Plate Set, completely with screws
to VDMA 24345
– End Plate set, Form D, for
Intermediate Plate, Form C
– Intermediate Plate, Form C Intermediate Plate Form C – Order Instructions and Weight
– Angle Base Plates
ISO-Size Weight (kg) Order Instructions Figure
Form E for for Intermediate
Plate Form C Type Order No.
– Accessories
1 0.240 S9-1-C KX 9079

2 0.360 S9-2-C KX 9419

X...
3 0.700 S9-3-C KX 9420
D
M AX and screws
The delivery includes: Intermediate Plate, completely with O-rings
IS O
b y
l a c ed
re p
Angle Base Plate Form E for Intermediate Plate Form C
Dimension Table ll be
wi
Figure

 


 



 

 

Order Instructions and Dimension Table (mm)

Order Instructions ISO-Size A B C D E F G
Type Order No.
S9-1-E KX 9081 1 37 12 25 42 110 22 G1/4
– – 2 – – – – – – –
S9-3-E KX 9425 3 45 17 29 70 190 36 G1/2
The delivery includes: Angle Base Plate, completely with O-rings and screws

Dimensions in mm

132
Adapter Plate for Linkage of ISO-Sizes 1, 2, 3 – Dimension Table and Order Instructions
Order Instructions for ISO A B Width Figure
Type Order No. Size

S9-1-2-KP KX 9430 1 to 2 20 135 45

S9-2-3-KP KX 9431 2 to 3 25 190 55



S9-1-3-KP KX 9432 1 to 3 35 190 50

The delivery includes: Adapter Plate with O-Rings and washers

Dummy Plate – Dimension Table and Order Instructions

Order Instructions for ISO A B Width Figure
Type Order No. Size

S9-1-BP KX 9082 1 12 70 40


S9-2-BP KX 9423 2 12 90 55

S9-3-BP KX 9424 3 12 110 70

X. .. 

A XD
OM
The delivery includes: Dummy Plate with gasket and screws

y I S
ce db
er
Plug – Order Instructions epla
l l b
wi Order No.
Order Instructions for ISO Size Figure
Type
S9-1-VS KX 5789 1

S9-2-VS KX 9426 2

S9-3-VS KX 9427 3

Dimensions in mm

133
Connection- Example of Plate Combination

platten End plate Form D

Intermediate Plate Form C

to ISO 5599
size 1, 2, 3 ISO-Size 2
Dummy
Plate
Versions
to VDMA 24345
– End Plate set Form D for
Intermediate Plate Form C
– Intermediate Plate Form C
– Angle Base Plates
Form E for Intermediate
Plate Form C
– Accessories

ISO-Size 3
X...
Adapter Plate
A XD
ISO-Size 1
I S OM
db y
lace
Angle Base Plate Form E

End Plate Form rDep

i l l be
w

134
 Ordering Code
       
       

neutral
       

        for Valve Islands

       


Channel divider

channel divider
Input module
Ident-No. Valve position

Connection

Number of

Position of
Electrical

inputs
Valves
1 2 3 4 5 6 7 8 9 10 11 12

04 06 08 10 12
even number of valve positions only
Important: Please specify the code for
the desired valve types

Input Modules
K X. ..
X DS
Pins IP20
Valve Islands – Sizes
M A Plug M8 IP65
PA 10381 Type: IM20-1/8
y ISO 04-08-12 Number of inputs
Connections:
ced b 16-20-24

pla
G1/8: valve outlets 28-32
G1/4: base plate
e r e
b
will
PA12867 Type: IM20-1/4
Connections:
Dual Pressure Operating
J with channel divider
G1/4: valve outlets
in Connection 1 (P)
G3/8: base plate
01 – 11 Position
of channel divider
Electrical Connection to valve position
Multipol-Version
DS with sub-D-conn. Ordering Code for Valves and Cover Plates
HI with industrial Code Symbol Description
connector A – Blanking plate on valve position

Valves M 14
4 2
12
5/2 way solenoid valve,
permanent signal with spring
04 to 4 valves return Type: S9 581RF-..
5 13
06 5 and 6 valves
J 4 2
12
5/2 way solenoid valve,
08 7 and 8 valves 14
impulse
Type: S9 581RF-..
10 9 and 10 valves 513

12 11 and 12 valves G 4 2 5/2 way solenoid valve,

14 13 and 14 valves
14 12 spring return to middle position,
middle position closed
16 15 and 16 valves 51 3 Type: S9 581RFG-..
B 4 2 5/2 way solenoid valve,
14 12
spring return to middle position,
middle position pressurized
513
Type: S9 581RFB-..
E 4 2 5/2 way solenoid valve,
14 12 spring return to middle position,
middle position exhausted
513 Type: S9 581RFE-..

135
136
Information on application
The contents of this catalog are not binding and are only intended for infor- Importance of EU Directives
mational purposes and are not to be considered as offer with legal effect. A
written confirmation of order from Parker Origa is authoritative for the con- Various Directives have been issued by the EU Commission in the course of
clusion of a contract; this confirmation is given solely under the respective the unification of the single European market; the following Directives are in
currently applicable Parker Origa General Terms of Sale and Delivery. These part of significance for ORIGA products:
are included in our price list and in the Internet at www.parker-origa.com. – Simple pressure vessels (87/404/EWG, amended by 90/488/EWG and
93/68/EWG)
All the products presented in this catalog are purely for commercial use. – Low-voltage electrical equipment (73/23/EWG, amended by 93/68/EWG)
None of the information or contents is appropriate for private consumers. – Machinery Directive (89/392/EWG, amended by 91/368/EWG, 93/44/
Private consumers cannot place orders based on the information in the EWG and 98/37/EG)
catalog. Please contact Parker Origa for further information. – Pressure Equipment Directive (97/23/EWG)
– Equipment and protective systems intended for use in potentially
All the products listed in this catalog are designed for typical pneumatic explosive atmospheres (ATEX Directive, 94/9/EG)
applications which e.g. are installed in higher-level machines. The reco- – Electromagnetic Compatibility Directive (EMV Directive, 89/336/EWG,
gnized technical rules for safe and expert work are to be observed for the use amended by 92/31/EWG)
and installation of pneumatic products. The precondition for the use of the
products is, unless stated otherwise, correctly prepared compressed air free If a product comes within the scope of application of one of these Guideli-
from aggressive media. Furthermore, the respective regulations of the legis- nes, then an EU Declaration of Conformity with CE mark (CE for Commun-
lator, the TÜV (Technical Inspection Association), the respective professional auté Européenne) is required. This CE marking does not represent a quality
associations or the VDE (Association of Electrical, Electronic and Information feature but verifies that the conformity assessment procedure specified has
Technologies) provisions also apply. been concluded successfully and the protective requirements of the relevant
EU Directives have been observed.
The technical data stated in this catalog is to be observed by the user. The
data stated may not be exceeded nor fallen short of. If such data is not Products which do not come under any of the above mentioned Directives
stated then it may be assumed that there are no such upper or lower limits may not bear the CE mark nor may any manufacturer’s declaration according
or restrictions for particular applications. In the case of unusual physical or to the EU Machinery Directive or Declaration of Conformity be issued for
chemical applications, consultation and clearances are to be obtained from these products.
Parker Origa
If a product may not be CE marked according to the Machinery Directive, it
Unless otherwise agreed in individual cases, the customer or end consumer must however be marked if it comes within the scope of application of any
is responsible for the disposal of the ORIGA products. Disposal by Parker other Directive.
Origa is not included in the price and this would have to be taken into ac- The following harmonized standards are applied in the design of ORIGA
count in the event of any applicable return to and disposal by Parker Origa. components and systems:
Technical data and representations – DIN EN ISO 12100 Safety of machinery
– DIN EN 60204.1 Electrical equipment of machines
The technical data and illustrations have been compiled with great care and
– DIN EN 983 Safety requirements for fluid power systems and their
to the best of our knowledge. We cannot assume any guarantee for the up-to-
components
dateness, correctness and completeness of the information.
The following Directives are of particular significance to Parker Origa:
The data and information such as illustrations, drawings, descriptions,
dimensions, weights, materials, technical and other performances as well as – ORIGA products in potentially explosive atmospheres, to which the above
the products and services described in general product descriptions, Parker mentioned ATEX Directive applies, are treated according to the Directive
Origa catalogs, brochures and price lists of any type are subject to change and CE and EX marked.
and may be modified or updated at any time without prior announcement – According to the Machinery Directive, ORIGA products are mainly
by Parker Origa. They are only binding in so far as the contract or confirma- components for installation in machines and therefore do not require an
tion of order expressly refers to them. Slight deviations from such product EU Declaration of Conformity with CE mark. Parker-ORIGA issues
descriptions are deemed as approved and do not affect the fulfillment of a manufacturer’s declaration according to the Machinery Directive for
contracts in so far as these are considered acceptable to customers. these components. This declaration corresponds to a great extent to
the Declaration of Conformity with the comment that commissioning is
This catalog does not contain any guarantees, assured characteristics or ag- only permitted if the machine or system conforms to the Directives. This
reements on condition by Parker Origa for the products represented, neither manufacturer’s declaration impacts neither our product liability based on
expressly nor implicitly, nor with regard to the availability of the products. the product liability law nor warranty assurances according to our General
Advertising statements regarding quality characteristics, properties or appli- Terms of Sale and Delivery. Neither does the manufacturer’s declaration
cations of ORIGA products are without legal obligation. affect our quality assurance measures according to our Quality
Management Manual nor our quality certification according to ISO 9001.
As far as legally permissible, any liability is excluded on the part of Parker – According to the Pressure Equipment Directive, ORIGA products are
Origa for direct or indirect damage, consequential damage, claims of any components of low hazard potential, thus most of the products do not
type and on any legal basis arising from the use of the information contained come under this Directive. The exceptions to this are maintenance
in this catalog. equipment from a certain pressure/volume level onwards. These
components are treated according to the Directive if required and bear the
Trademarks, copyright and reproduction CE mark.
The representation of industrial rights such as brands, logos, registered
trademarks or patents in this catalog does not include the granting of ORIGA products are excluded from the following EU Guidelines:
licenses or rights of use. The use of these is not permitted without the – End-of-life vehicles (2000/53/EG).
express consent of Parker Origa. The entire contents of this catalog are the – Waste Electronic and Electrical equipment (WEEE, 2002/96/EG) and
intellectual property of Parker Origa. Within the meaning of copyright, any Restriction on Hazardous Substances (RoHS, 2002/95/EG).
unlawful use of intellectual property, even extracts, is prohibited. Reprinting, – Pressure Equipment Directive (97/23/EWG) with the above mentioned
reproduction and translation (even extracts) are only permitted with the prior exceptions.
written consent of Parker Origa.
Parker Worldwide

AE – UAE, Dubai FR – France, Contamine s/Arve RO – Romania, Bucharest

Tel: +971 4 8127100 Tel: +33 (0)4 50 25 80 25 Tel: +40 21 252 1382
[email protected] [email protected] [email protected]
AR – Argentina, Buenos Aires GR – Greece, Athens RU – Russia, Moscow
Tel: +54 3327 44 4129 Tel: +30 210 933 6450 Tel: +7 495 645-2156
[email protected] [email protected]
AT – Austria, Wiener Neustadt
Tel: +43 (0)2622 23501-0 HK – Hong Kong SE – Sweden, Spånga
[email protected] Tel: +852 2428 8008 Tel: +46 (0)8 59 79 50 00
[email protected]
AT – Eastern Europe, HU – Hungary, Budapest
Wiener Neustadt Tel: +36 1 220 4155 SG – Singapore
Tel: +43 (0)2622 23501 900 [email protected] Tel: +65 6887 6300
[email protected]
IE – Ireland, Dublin SK – Slovakia, Banská Bystrica
AU – Australia, Castle Hill Tel: +353 (0)1 466 6370 Tel: +421 484 162 252
Tel: +61 (0)2-9634 7777 [email protected] [email protected]
AZ – Azerbaijan, Baku IN – India, Mumbai SL – Slovenia, Novo Mesto
Tel: +994 50 2233 458 Tel: +91 22 6513 7081-85 Tel: +386 7 337 6650
[email protected] [email protected]
IT – Italy, Corsico (MI)
BE/LU – Belgium, Nivelles Tel: +39 02 45 19 21 TH – Thailand, Bangkok
Tel: +32 (0)67 280 900 [email protected] Tel: +662 717 8140
[email protected]
JP – Japan, Tokyo TR – Turkey, Istanbul
BR – Brazil, Cachoeirinha RS Tel: +(81) 3 6408 3901 Tel: +90 216 4997081
Tel: +55 51 3470 9144 [email protected]
KR – South Korea, Seoul
BY – Belarus, Minsk Tel: +82 2 559 0400 TW – Taiwan, Taipei
Tel: +375 17 209 9399 Tel: +886 2 2298 8987
KZ – Kazakhstan, Almaty
[email protected]
Tel: +7 7272 505 800 UA – Ukraine, Kiev
CA – Canada, Milton, Ontario [email protected] Tel +380 44 494 2731
Tel: +1 905 693 3000 [email protected]
LV – Latvia, Riga
CH – Switzerland, Etoy Tel: +371 6 745 2601 UK – United Kingdom,
Tel: +41 (0) 21 821 02 30 [email protected] Warwick
[email protected] Tel: +44 (0)1926 317 878
MX – Mexico, Apodaca
[email protected]
CL – Chile, Santiago Tel: +52 81 8156 6000
Tel: +56 2 623 1216 US – USA, Cleveland
MY – Malaysia, Shah Alam
Tel: +1 216 896 3000
CN – China, Shanghai Tel: +60 3 7849 0800
Tel: +86 21 5031 2525 VE – Venezuela, Caracas
NL – The Netherlands,
Tel: +58 212 238 5422
CZ – Czech Republic, Klecany Oldenzaal
Tel: +420 284 083 111 Tel: +31 (0)541 585 000 ZA – South Africa,
[email protected] [email protected] Kempton Park
Tel: +27 (0)11 961 0700
DE – Germany, Kaarst NO – Norway, Ski
[email protected]
Tel: +49 (0)2131 4016 0 Tel: +47 64 91 10 00
[email protected] [email protected]
DK – Denmark, Ballerup NZ – New Zealand, Mt Wellington
Tel: +45 43 56 04 00 Tel: +64 9 574 1744
[email protected]
PL – Poland, Warsaw
ES – Spain, Madrid Tel: +48 (0)22 573 24 00
Tel: +34 902 33 00 01 [email protected]
[email protected]
PT – Portugal, Leca da Palmeira
FI – Finland, Vantaa Tel: +351 22 999 7360
Tel: +358 (0)20 753 2500 [email protected]
[email protected]

© 2009 Parker-Origa GmbH - All rights reserved. P- A4P026E 07/2009

Parker-Origa GmbH
Industriestr. 8
70794 Filderstadt, Deutschland
Tel. +49 (0)7158 17030
Fax +49 (0)7158 64870
Email: [email protected]
www.parker-origa.com