May.

2002 SD-80

SERVICE NOTES
Issued by RJA
SPECIFICATIONS.............................................................1 CIRCUIT BOARD (JACK SHEET) ................................20
LOCATION OF CONTROLS PARTS LIST ...................3 CIRCUIT DIAGRAM (MAIN BOARD 1/7)................21
LOCATION OF CONTROLS ..........................................3 CIRCUIT DIAGRAM (MAIN BOARD 2/7)................23
EXPLODED VIEW PARTS LIST .....................................5 CIRCUIT DIAGRAM (MAIN BOARD 3/7)................25
EXPLODED VIEW ............................................................6 CIRCUIT DIAGRAM (MAIN BOARD 4/7)................27
PARTS LIST........................................................................7 CIRCUIT DIAGRAM (MAIN BOARD 5/7)................29
CHECKING THE VERSION NUMBER.......................12 CIRCUIT DIAGRAM (MAIN BOARD 6/7)................31
DATA SAVING AND LOADING ................................12 CIRCUIT DIAGRAM (MAIN BOARD 7/7)................33
RESTORING FACTORY SETTINGS ............................12 CIRCUIT BOARD (JACK SHEET) ................................35
SYSTEM SOFTWARE UPDATING PROCEDURE ....12 CIRCUIT DIAGRAM (JACK SHEET 1/2) ...................37
TEST MODE.....................................................................14 CIRCUIT DIAGRAM (JACK SHEET 2/2) ...................39
BLOCK DIAGRAM.........................................................17 ERROR MESSAGES ........................................................41
CIRCUIT BOARD (MAIN BOARD).............................19

Copyright © 2002 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written permission
of ROLAND CORPORATION.

17058084E0 Printed in Japan (0080) (CM)

 May.2002

SPECIFICATIONS
Number of parts
32

Maximum Polyphony
128 voices

Preset Sounds
Sound Maps: 6 (Classical, Contemporary, Solo, Enhanced, Special1, Special2)
Instruments: 1050
Drum Sound Sets: 30

User Sounds
Instruments: 128
Drum Sound Sets: 16

Effects
System Effects: Reverb (6 types), Chorus (6 types)
Insertion Effects: Multi-effects x 3 (90 types)

Display
20 characters, 2 lines (backlight LCD)

Jacks and Connectors

USB connector
Digital Audio Output connectors (conform to S/P DIF)
COAXIAL type
OPTICAL type
Audio Output jacks 1 (Stereo, or Individual x 2)
Audio Output jacks 2 (Stereo, or Individual x 2)
Headphones jack (Stereo)
MIDI Connectors (IN 1, IN 2, OUT 1, OUT 2)

Power Supply
AC 120 V, AC 230 V or AC 240 V

Power Consumption
10 W (AC 120 V)
10 W (AC 230 V)
10 W (AC 240 V)

Dimensions
280 (W) x 258.4 (D) x 46 (H) mm
11-1/16 (W) x 10-3/16 (D) x 1-13/16 (H) inches

Weight
1.8 kg
4 lbs

Accessories
USB Cable : (#02239578)
AC Cable : 120V (#00894378)
230V (#00894389)
230VE (#00907001)
240V (#23495124)
Owner’s manual set : English (#72125789)
: for EU (#72125790)
: Japanese (#72125778)
CD-ROM : (#02903101)
Rack-mount adaptor : (#02906123)
Desk-stand mount : (#02906134)
Cushion set for Desk-stand : (#03013701)

1
SD-80

2
 May.2002 SD-80

LOCATION OF CONTROLS LOCATION OF CONTROLS

PARTS LIST fig.bunkai-
3

No PART PART NAME DESCRIPTION Q’TY

CODE
1 02675701 WIRING ASSY WIRING W3(AC IN- 1
LET+GND)
2 13449146 YKB21-5012 (W/ 6.5MM JACK 4
SW)
3 02565390 GP1FA501TZ OPTICAL CONNECTOR
TX
4 01343723 YKC21-3117(OR- RCA(PIN) JACK 1
ANGE)
5 01454945 SSSF112-S06N1 SLIDE SWITCH 1
6 02892878 2DJ-0060003 DIN(MIDI) JACK 4
7 02781101 YKF45-0020 USB CONNECTOR 1
8 02906189 DISPLAY COV- 1
ER
8 02780067 RCM2072M-B LCD 1
9 02904156 EC12E2420801 ROTARY ENCODER 1
9 02906201 S R-KNOB L DBL 1
10 02906178 RUBBER SW 1
11 13119710 SKHQFM SWITCH 4
12 02781634 SKRGAED010 TACT SWITCH 6
13 01348623 SLR-56VCT32 RED 1
14 01348634 SLR-56MCT32 GREEN 1
15 02011856 SLR-56DCT32 ORANGE 1
16 02892512 P R-KNOB MF-A DBL/LCG 1
16 02904145 RK09L12B0A22 9M/M ROTARY POTEN- 1
10KBX2 TIOMETER
17 22225375 P B-ESCT SD1H 1
BLK
17 02781501 P S-KEY MX DBL 1
17 01676512 SDKLA1-B PUSH SWITCH 1
18 13449148 YKB21-5009 JACK 1
19 03014801 ISOLATOR LCD 1
MASK
fig.escut

When using #22225375 P B-ESCT SD1H BLK, cut a part as shown in figure.

3 4
 May.2002

EXPLODED VIEW PARTS LIST

[Parts]
No. PART CODE PART NAME DESCRIPTION Q’TY
1 02906245 TOP COVER 1
2 02906145 BOTTOM CHASSIS 1
3 02906190 FRONT PANEL 1
4 02906189 DISPLAY COVER 1
5 02906201 S R-KNOB L DBL 1
6 02906178 RUBBER SW 1
7 02892512 P R-KNOB MF-A DBL/LCG 1
8 02781501 P S-KEY MX DBL 1
9 22225375 P B-ESCT SD1H BLK 1
10 03014801 ISOLATOR LCD MASK 1
11 72120445 MAIN BOARD ASSY 1
12 72120523 LCD BOARD ASSY 1
13 72120545 ENCODER BOARD ASSY 1
14 72120512 PANEL BOARD ASSY 1
15 72120534 VOLUME BOARD ASSY 1
16 72120490 JACK1 BOARD ASSY 1
17 72120501 JACK2 BOARD ASSY 1
18 72125767 POWER ASSY 1
19 02906256 INSULATING SHEET 1
20 12359137 RUBBER FOOT SJ-5012 BLK 4
21 02344001 WIRING 12X100-P2.0-PHR-PHR-F 1
22 02343545 WIRING 8X150-P2.0-PHR-PHR-F 1
23 02343245 WIRING 6X200-P2.0-PHR-PHR-F 1
24 02342012 WIRING 4X200-P2.0-PHR-PHR-F 1
25 02341967 WIRING 4X50-P2.0-PHR-PHR-F 1
26 02908823 BAN CARD BNCD-P=1.00-K-16-120 1
27 02239390 BAN CARD BNCD-P=1.00-K-14-200 1
28 02903067 BAN CARD BNCD-P=1.00-K-18-60 1
[Screws]

No. PART CODE PART NAME DESCRIPTION Q’TY

a 40011490 SCREW M3X6 PAN MACHINE W/SW BZC 4
b 40013056 SCREW M3X6 PAN MACHINE W/SW+PW ZC 4
c 40011378 SCREW M4X8 BINDING TAPTITE S FE BZC 1
d 40011312 SCREW 3X8 BINDING TAPTITE P BZC 2
e 40011056 SCREW 3X6 BINDING TAPTITE B ZC 15
f 40455167 SCREW 3X8 TAPTITE B OVAL HEAD NI 5
g 40011090 SCREW 3X6 BINDING TAPTITE B BZC 3
h 40012490 SCREW 4X10 BINDING TAPTITE P BZC 2
I 40127689 SCREW 3X10 BINDING TAPTITE S BZC 8
j 40454856 SCREW M4X10 BINDING NI 1
k 40126867 JACK WASHER M12X16X0.5 FE NI 1
L 40016423 JACK NUT HLJ0999-01-250 12X14X2P 1.0 1
m 17048631 VR ACCESSORY WASHER M9 VR ACCESSORY WASHER M9 2
n 17048630 VR ACCESSORY NUT M9 VR ACCESSORY NUT M9 2

5
 SD-80

EXPLODED VIEW
fig.explo

i
17

27 28 19
26 e b

e c

25 11 16

a
18
13

d
a
22 j

23
h
21 2
10 12

4
m
n
14
e 24

5 m 20 15
n
f 7
3
6 e
k
L

8
9
f

6
 May.2002

PARTS LIST
fig.part1e

SAFETY PRECAUTIONS: CONSIDERATION ON PARTS ORDRING

The parts marked have When ordering any parts listed in the parts list, please specify the following items in the order sheet.
safety-related characteristics. Use QTY PART NUMBER DESCRIPTION MODEL NUMBER
only listed parts for replacement. Ex. 10 22575241 Sharp Key C-20/50
15 2247017300 Knob (orange) DAC-15D
Failure to completely fill the above items with correct number and description will result in delayed or even
undelivered replacement.

NOTE: The parts marked # are new. (initial parts)

MB : MAIN BOARD, J1B : JACK1 BOARD, J2B : JACK2 BOARD, PNB : PANEL BOARD, LB : LCDBOARD, VB : VOLUME BOARD, POB : POWER ASSY, EB :
ENCODER BOARD

CASING
# 02906189 DISPLAY COVER 1
# 02906245 TOP COVER 1
22225375 P B-ESCT SD1H BLK 1
# 02906190 FRONT PANEL 1

CHASSIS
# 02906145 BOTTOM CHASSIS 1

KNOB, BUTTON
02781501 P S-KEY MX DBL 1
# 02906178 RUBBER SW 1
02892512 P R-KNOB MF-A DBL/LCG 1
# 02906201 S R-KNOB L DBL 1

SWITCH
01676512 SDKLA1-B PUSH SWITCH SW1 on POB 1
02781634 SKRGAED010 TACT SWITCH SW9,SW7,SW8,SW11,SW6,SW10 on PNB 6
13119710 SKHQFM SWITCH SW3,SW4,SW5,SW12 on PNB 4
01454945 SSSF112-S06N1 SLIDE SWITCH SW2 on J1B 1

JACK, EXT TERMINAL

13449148 YKB21-5009 JACK JK12 on VB 1
13449146 YKB21-5012 (W/SW) 6.5MM JACK JK11,JK10 on J1B,JK9,JK8 on J2B 2
+2
02892878 2DJ-0060003 DIN(MIDI) JACK JK3,JK6,JK5,JK4 on J1B 4
01343723 YKC21-3117(ORANGE) RCA(PIN) JACK JK2 on J1B 1
02781101 YKF45-0020 USB CONNECTOR JK7 on J1B 1

DISPLAY UNIT
02780067 RCM2072M-B LCD IC7 on LB 1
NOTE: Replacement RCM2072M-B should be made on a unit base.

POWER SUPPLY UNIT

02457745 A1DU2L3B104 VER.3 SWITCHING REGULATOR BOARD1 on POB 1
NOTE: Replacement A1DU2L3B104 VER.3 should be made on a unit base.

PCB ASSY
# 72120445 MAIN BOARD ASSY 1

# 72120534 VOLUME BOARD ASSY 1

# 72120545 ENCODER BOARD ASSY 1
# 72125767 POWER ASSY 1
NOTE: ‘POWER ASSY’ includes the following parts.
# ******** POWER BOARD ASSY Assy(Unit) 1
NOTE: ‘POWER BOARD ASSY’ includes the following parts.
02675701 WIRING ASSY WIRING W3(AC INLET+GND) JK1 on POB 1
# 03012089 INSULATING SHEET B104 1

# ******** PSW BOARD ASSY Assy(Unit) 1

NOTE: ‘PSW BOARD ASSY’ includes the following parts.
# 02906090 WIRING 2X50-P4-3PSDN-3PSDN-F CN12 on POB 1

7
 SD-80

PCB ASSY
# 72120523 LCD BOARD ASSY 1
NOTE: ‘LCD BOARD ASSY’ includes the following parts.
02453345 LCD HOLDER 1
# 02908834 LEAF REFLECTOR 1

# 72120512 PANEL BOARD ASSY 1

# 72120501 JACK2 BOARD ASSY 1
NOTE: ‘JACK2 BOARD ASSY’ includes the following parts.
12199584 GROUNDING TERMINAL M1698 TER1 on J1B,TER3,TER2 on J2B 2

# 72120490 JACK1 BOARD ASSY 1

NOTE: ‘JACK1 BOARD ASSY’ includes the following parts.
12199584 GROUNDING TERMINAL M1698 TER1 on J1B,TER3,TER2 on J2B 1

IC
# 02902867 M37641M8-137FP VER1.00 IC (8BIT CPU) IC17 on MB 1
# 02903723 HD6417706 IC (32BIT CPU) IC2 on MB 1
01455956 TC223C660CF-503 IC (RA08-503) IC27,IC19 on MB 2
02450401 GM71C18163CJ-6 IC (DRAM) IC26,IC30 on MB 2
# 03015212 SDRAM LC3816161ET-70-TLM IC (DRAM) IC6,IC4 on MB 2
# 03010612 UPD23C128040ALGY525MJH IC (MASK ROM) IC28 on MB 1
# 03010623 UPD23C128040ALGY526MKH IC (MASK ROM) IC29 on MB 1
# 02902878 LH28F160BJE-BTL80 IC (FLASH MEMORY) IC3 on MB 1
01897201 PCM1716E IC (AD/DA) IC32,IC34 on MB 2
01901623 TC74LVXC3245FS IC (CMOS) IC12,IC10 on MB 2
01349590 TC7WU04FU(TE12L) IC (CMOS) IC21 on MB 1
02675689 HD74LV245ATELL IC (CMOS) IC25,IC8,IC22,IC23,IC24,IC20 on MB 6
01348901 TC7SH04FU(TE85L) IC (CMOS) IC37,IC5 on MB 2
01348912 TC7SH08FU(TE85L) IC (CMOS) IC14 on MB 1
02451712 HD74LV14ATELL IC (CMOS) IC16 on MB 1
02451912 HD74LV00ATELL IC (CMOS) IC7 on MB 1
02565734 74VHCT245AMTCX IC (CMOS) IC9,IC11 on MB 2
01675023 TC74VHC139FT(CEL) IC (CMOS) IC18 on MB 1
02675645 HD74LV04ATELL IC (CMOS) IC15 on MB,IC4 on J1B 2
# 02902856 TC74VHCT139AFT IC (CMOS) IC13 on MB 1
15289105 UPC4570G2-E2 IC (BIPOLAR OP AMP) IC31,IC35 on MB 2
15289402 TA78L05F(TE12L) IC (REGULATOR) IC36 on MB 1
02456934 M62292FP-D60J IC (DC-DC REGULATOR) IC1 on MB 1
01785178 TC9271FS IC IC33 on MB 1
15289120 NJM4565MD-TE3 IC (BIPOLAR OP AMP) IC6 on VB 1
15259706T0 TC74HCU04AF(EL) IC (HS-CMOS) IC1 on J1B 1
02565390 GP1FA501TZ TX IC (OPTICAL CONNECTOR) CN2 on J1B 1
# 02900545 PC410LKNIP IC (PHOTO COUPLER) IC2,IC3 on J1B 2

TRANSISTOR
02671012 2SA1530A-T12-1R TRANSISTOR Q5,Q8,Q10 on MB 3
02671023 2SC3052-T12-1E TRANSISTOR Q6,Q11,Q9 on MB 3
02458178 PW.MOS FET FW111-TL TRANSISTOR Q1 on MB 1
# 02905501 SSM3J02T TRANSISTOR Q7 on MB 1
02670989 DTB113ZK-146T TRANSISTOR Q3,Q2,Q4 on MB 3
15329536 RN1442-A(TE85L) TRANSISTOR Q6,Q5 on J1B,Q3,Q4 on J2B ,Q8,Q7 on VB 2
+2
+2
01451245 RN1414(TE85L) TRANSISTOR Q2,Q1 on J1B 2

DIODE
01780045 RB051L-40 SCHOTTKY DIODE D1,D2 on MB 2
01897189 MA147-(TX) ARRAY DIODE DA3,DA1 on MB 2
15039169 DSK10C-ET1 RECTIFIER DIODE D2,D1 on POB 2
# 02907823 02DZ6.8-X-(TPH3) ZENER DIODE D5 on LB 1
# 02907812 CL-191B1-X LED LED8,LED7,LED9,LED10,LED6 on LB 5
15339130 MA142WK-(TX) ARRAY DIODE DA7,DA6 on J1B 2
,DA5,DA4,DA3,DA2,DA1 on PNB +5
01348623 SLR-56VCT32 LED (RED) LED3,LED1,LED2 on PNB 3
01348634 SLR-56MCT32 LED GREEN LED4 on PNB 1
02011856 SLR-56DCT32 LED (ORG) LED5 on PNB 1

RESISTOR
00567023 RPC05T 101 J MTL.FILM RESISTOR R8,R9,R26 on MB,R3,R8 on J1B 3
+2
00567101 RPC05T 391 J MTL.FILM RESISTOR R19,R20 on MB 2
00567556 RPC05T 105 J MTL.FILM RESISTOR R42,R28 on MB 2
02672290 MCR100JZHJ681 MTL.FILM RESISTOR R112 on MB 1
00567112 RPC05T 471 J MTL.FILM RESISTOR R114,R113,R83 on MB,R23,R22,R20,R19 on 3
J1B,R17,R16,R14,R13 on J2B +4
+4

8
May.2002

RESISTOR
00567201 RPC05T 272 J MTL.FILM RESISTOR R98,R64,R96,R68 on MB 4
00567245 RPC05T 472 J MTL.FILM RESISTOR R111,R108,R110,R109 on MB ,R36,R37 on 4
VB +2
00567267 RPC05T 682 J MTL.FILM RESISTOR R65,R66,R69,R70,R75,R81,R97,R99 on MB 8
00567278 RPC05T 822 J MTL.FILM RESISTOR R82,R76,R71,R67 on MB 4
00567289 RPC05T 103 J MTL.FILM RESISTOR R12,R49,R50,R56,R58,R59,R60,R61,R62,R78, 28
R79,R85,R89,R10,R47,R14,R7,R16,R45,R15, +2
R90,R37,R34,R38,R48,R46,R6,R40 on +2
MB,R24,R21 on J1B ,R30,R27 on VB
00567412 RPC05T 104 J MTL.FILM RESISTOR R116,R86,R101,R88,R115 on MB ,R18,R15 on 5
J2B +2
01011856 RPC05T 0R0 J MTL.FILM RESIST0R R74,R13,R95,R51,R33,R63,R35 on MB 7
00567067 RPC05T 221 J MTL.FILM RESISTOR R107,R106 on MB,R11,R10,R6,R5 on J1B 2
,R26,R29 on VB +4
+2
00567156 RPC05T 102 J MTL.FILM RESISTOR R27,R5,R2,R1,R44,R21 on MB,R7,R2,R12 on 6
J1B +3
00566912 RPC05T 220 J MTL.FILM RESISTOR R41,R24,R39,R25 on MB 4
00567089 RPC05T 331 J MTL.FILM RESISTOR R36 on MB 1
00567178 RPC05T 152 J MTL.FILM RESISTOR R31 on MB 1
00567212 RPC05T 332 J MTL.FILM RESISTOR R91 on MB 1
00567323 RPC05T 223 J MTL.FILM RESISTOR R57,R43 on MB 2
00567334 RPC05T 273 J MTL.FILM RESISTOR R72,R84,R73,R77 on MB 4
01897912 RR0816Q-330-D MTL.FILM RESISTOR R30,R29 on MB 2
02673401 RR0816P-102-D MTL.FILM RESISTOR R3 on MB 1
15399989 MCR50JZH680 1/2W CHIP RESISTOR R87 on MB 1
00344278 EXBV8V102JV RESISTOR ARRAY RA51,RA27,RA26 on MB 3
01011845 EXBV8V0R000V RESISTOR ARRAY RA7 on MB 1
02678534 EXB2HV103V RESISTOR-ARRAY RA40,RA46,RA14,RA52,RA45,RA41,RA29, 8
RA20 on MB
02457723 EXB2HVR000V RESISTOR-ARRAY RA3,RA1 on MB 2
15409113 EXBV8V103JV RESISTOR ARRAY RA42,RA47,RA22,RA12,RA50 on MB 5
01457145 EXBE10C103J RESISTOR ARRAY RA38,RA37,RA39,RA5,RA17,RA18,RA35,R 9
A36,RA6 on MB
02456878 EXB2HV220JV RESISTOR-ARRAY RA13,RA10,RA2,RA4,RA9,RA11,RA16,RA1 12
9,RA21,RA28,RA8,RA15 on MB
01454890 MCR50 JZH J 220 MTL.FILM RESISTOR R28,R25 on VB 2
00567034 RPC05T 121 J MTL.FILM RESISTOR R4,R9 on J1B ,R35,R34,R33,R32,R31 on LB 2
+5
00566967 RPC05T 470 J MTL.FILM RESISTOR R38 on J1B 1
00567001 RPC05T 750 J MTL.FILM RESISTOR R1 on J1B 1
00126112 EXBV8V101JV RESISTOR ARRAY RA1 on J1B 1

POTENTIOMETER
# 02904145 RK09L12B0A22 10KBX2 9M/M ROTARY POTENTIOM- VR1 on VB 1
ETER

CAPACITOR
01675367 GRM39CH471J50PT CERAMIC CAPACITOR C18,C17 on MB 2
00567978 GRM39F104Z25PT CERAMIC CAPACITOR C138,C119,C150,C149,C148,C147,C146,C14 92
5,C144,C143,C142,C153,C140,C155,C137,C1 +10
36,C133,C132,C131,C130,C129,C126,C211,C +1
125,C121,C120,C141,C187,C212,C213,C214, +3
C210,C207,C205,C204,C202,C201,C198,C15 +2
1,C188,C123,C186,C183,C180,C179,C168,C1
64,C163,C162,C161
C159,C158,C157,C156,C189,C90,C58,C109,
C59,C111,C60,C56,C76,C108,,C118,C117,C1
16,C115,C114,C77,C112,C113,C61,C52,C3,C
8,C20,C47,C48,C49,C110,C51,C107,C53,C54
,C55,C91,C93,C99,C104,C105,C50 on MB,
C9,C26,C1,C16,C15,C3,C14,C13,C12,C11 on
J1B,C21 on J2B ,C31,C33,C35 on VB,C37,C36
on LB
00567823 GRM39B102K50PT CERAMIC CAPACITOR C81,C82,C78,C68,C79,C80,C84,C74,C73,C72 22
,C71,C87,C69,C85,C67,C66,C65,C64,C63,C6
2,C70,C83 on MB
00567867 GRM39B222K50PT CERAMIC CAPACITOR C124,C154 on MB 2
00567945 GRM39B103K50PT CERAMIC CAPACITOR C39,C34,C35,C36,C31,C38,C30,C40,C41,C44 29
,C45,C46,C37,C13,C29,C28,C27,C26,C24,C2
3,C22,C21,C19,C15,C14,C12,C10,C33,C11
on MB
01672412 GRM39CH150J50PT CERAMIC CAPACITOR C101,C102,C128 on MB 3
01674445 ECUV1H681JCV CERAMIC CAPACITOR C94 on MB 1
01675189 GRM39CH180J50PT CERAMIC CAPACITOR C127 on MB 1
01675190 GRM39CH220J50PT CERAMIC CAPACITOR C86 on MB 1
02456778 ECJ1VB1C104K CERAMIC CAPACITOR C92 on MB 1
01784123 ECHU1H471JX5 POLYEST. CAPACITOR C165,C177,C184,C193 on MB 4
01899223 ECHU1H102JX5 POLYEST. CAPACITOR C190,C166,C196,C178 on MB 4
02017067 ECEV0JA471P ELECTROLYTIC CAPACITOR C25 on MB 1
02345101 RV2-16V100M-R ELECTROLYTIC CAPACITOR C57,C199,C200,C182,C181,C167,C152,C122, 13
C89,C88,C9,C216,C103 on MB
02783412 6SVP150 OS-CON ELECTROLYTIC CAPACITOR C1,C7 on MB 2

9
 SD-80

CAPACITOR
# 02905590 4SVP330 ELECTROLYTIC CAPACITOR C6 on MB 1
15369263 ECEV1HA2R2SR ELECTROLYTIC CAPACITOR C98 on MB 1
01904856 ECEV1CA470WR ELECTROLYTIC CAPACITOR C174,C220,C219,C218,C217,C169,C192,C19 8
5 on MB
02124923 RV3-25V470MZ7-R ELECTROLYTIC CAPACITOR C203,C209,C206,C197,C191 on MB 5
02345234 RV2-6V101M-R ELECTROLYTIC CAPACITOR C4,C208,C135 on MB 3
01893267 TCFGA0J106M8R TANTALUM CAPACITOR C106,C32,C16,C42,C139 on MB 5
01675278 GRM39CH101J50PT CERAMIC CAPACITOR C10,C23,C25,C40 on J1B,C20,C18 on J2B 4 +2
,C27,C30 on VB +2
00674423 ECA0JM102B 1000U/6.3V ELECTROLYTIC CAPACITOR C39 on POB 1
02127812 RA2-25V470MT2 CERAMIC CAPACITOR C19,C17 on J2B,C24,C22 on POB 2 +2
13649269 ECA1CM100B 10UF/16V ELECTROLYTIC CAPACITOR C4,C7,C38,C2 on J1B 4

INDUCTOR, COIL, FILTER

02783467 SLF10145T-470M1R4 CHOKE COIL L2 on MB 1
02783478 SLF10145T-101M1R0 CHOKE COIL L1 on MB 1
01909645 EXCML16A270U FERRITE-BEAD L11,L12,L14,L20 on J1B,L17 on J2B ,L23 on 1
VB +1
+4
01909656 EXC3BB601H FERRITE-BEAD L3,L6,L19,L18,L13,L10,L9,L8,L7,L2,L1,L5,L 2
4 on J1B,L16,L15 on J2B ,L22,L21 on VB +2
+1
3

CRYSTAL, RESONATOR
00891801 MA-406 24.000MHZ TE24 CRYSTAL X1 on MB 1
02673134 MA-406 16.9344MHZ CRYSTAL X2 on MB 1

ENCODER
# 02904156 EC12E2420801 ROTARY ENCODER EN1 on EB 1

CONNECTOR
# 02905601 14FMN-BMT-A-TF CONNECTOR CN4 on MB 1
# 02905612 16FMN-BMT-A-TF CONNECTOR CN5 on MB 1
# 02905623 18FMN-BMT-A-TF CONNECTOR CN6 on MB 1
# 02902801 B4B-PH-SM3-TB CONNECTOR CN3 on MB 1
# 02902823 B12B-PH-SM3-TB CONNECTOR CN1 on MB 1
# 02902834 B8B-PH-SM3-TB CONNECTOR CN7 on MB 1
# 02902845 B6B-PH-SM3-TB CONNECTOR CN8 on MB 1
13369664 S4B-PH-K-S(4P) CONNECTOR CN4 on J2B ,CN6 on VB ,CN10 on EB 1
+1
+1
13369668 S8B-PH-K-S JST (8P) CONNECTOR CN7 on VB 1
13369564 B12B-PH-K-S JST CONNECTOR CN1 on POB 1
02011934 16FMN-BTK CONNECTOR CN9 on LB 1
# 02235467 14FMN-STK CONNECTOR CN8 on PNB 1
02011956 18FMN-BTK CONNECTOR CN3 on J1B 1
13369666 S6B PH-K-S(6P) CONNECTOR CN5 on J1B 1

WIRING, CABLE
# 02341967 WIRING 4X50-P2.0-PHR-PHR-F CN3 on MB to CN10 on EB 1
02342012 WIRING 4X200-P2.0-PHR-PHR-F CN4 ON J2B to CN6 on VB 1
02343245 WIRING 6X200-P2.0-PHR-PHR-F CN8 on MB to CN5 on J1B 1
# 02343545 WIRING 8X150-P2.0-PHR-PHR-F CN7 on MB to CN7 on VB 1
# 02344001 WIRING 12X100-P2.0-PHR-PHR-F CN1 on MB to CN1 on POB 1
# 02908823 BAN CARD BNCD-P=1.00-K-16-120 CN5 on MB to CN9 on LB 1
02239390 BAN CARD BNCD-P=1.00-K-14-200 CN4 on MB to CN8 on PNB 1
# 02903067 BAN CARD BNCD-P=1.00-K-18-60 CN6 on MB to CN3 on J1B 1

TRANSFORMER
02019478 (7KQ5) 19832A PULSE TRANS T1 on J1B 1

SCREW
40454856 SCREW M4X10 BINDING NI 1
40455167 SCREW 3X8 TAPTITE B OVAL HEAD NI 5
40011056 SCREW 3X6 BINDING TAPTITE B ZC 5
40011090 SCREW 3X6 BINDING TAPTITE B BZC 5
40011312 SCREW 3X8 BINDING TAPTITE P BZC 2
40012490 SCREW 4X10 BINDING TAPTITE P BZC 2
40011378 SCREW M4X8 BINDING TAPTITE S FE BZC 1
40011490 SCREW M3X6 PAN MACHINE W/SW BZC 4
40013056 SCREW M3X6 PAN MACHINE W/SW+PW ZC 16
40127689 SCREW M3X10 BINDING TAPTITE S FE BZC 8
40126867 JACK WASHER M12*16*0.5 FE NI 1

10
May.2002

SCREW
40016423 JACK NUT HLJ0999-01-250 12X14X2P 1.0 1
17048631 VR ACCESSORY WASHER M9 2
17048630 VR ACCESSORY NUT M9 2

PACKING
# 02905634 PACKING CASE SLEEVE ENGLISH 1
+1
# 02906212 PACKING CASE SLEEVE JAPANESE 1
# 03012078 PAD UPPER 1
# 02906101 PAD ADAPTOR 1
# 02906112 PAD LOWER 1
# 02906223 PACKING CASE 1
# 02906234 OUTER PACKING CASE 1
+1

MISCELLANEOUS
12359137 RUBBER FOOT SJ-5012 BLK 4
# 02906256 INSULATING SHEET 1
# 03014801 ISOLATOR LCD MASK 1

ACCESSORIES (STANDARD)
00894367 AC CORD SET 100V SP18A+IS14 VCTF2X0.75 1
00894378 AC CORD SET 120V SP301+IS14 SJT18/3 1
00894389 AC CORD SET 230V SP22+IS14 H05VV-F3G1.0 1
23495124 AC CORD SET 240VA SC-144-JO1 ES303- 1
10HMA
00907001 AC CORD SET 240VE KP-610 GTTBS-3 KS-31A 1
02239578 USB CONNECT CORD YAF11-0791 2M 1
# 02903101 CD-ROM DRV&DEMO J/E W/M 1
+1
+1
# ******** DTM REGISTRATION CARD 1
2000
01455601 CONVERTER PLUG PIN-PHONE X2 1
# 02905678 CD MULTI MANUAL 1
# 72125778 OWNER’S MANUAL SET JAPANESE 1
# 72125790 OWNER’S MANUAL SET EEU 1
# 72125789 OWNER’S MANUAL SET ENGLISH 1
# ******** WARRANTY REGISTRATION (ENA) 1
CARD
40348001 WARRANTY CARD EDIROL JAPAN ONLY 1
# 02906123 RACK ANGLE FOR 280 2
# 02906134 STAND 1
# 03013701 FOOT STAND CUSHION SET 1

11
 SD-80

CHECKING THE VERSION 2. Press the [SYSTEM] button, then press the [PAGE>] button to display
Bulk Dump.
NUMBER 3. Display the USER AREA by rotating the [VALUE] control.

4. Start sequencer recording.

While holding down the [INST], [PART>] and [SHIFT] buttons, turn on the
5. Press the [ENTER] button of the SD-80. The “Transmit SysEx” message
power.
appears on the screen of the SD-80.
Keep holding down these buttons until the program version appears.
The version number appears at the bottom left of the screen. 6. Stop sequencer recording when the “Transmit SysEx” message
fig.3-1_65 disappears.

7. Save the song on the sequencer in the hard disk or a floppy disk.

DATA LOADING
The SD-80 and the computer must be connected with the USB cable.
To use the machine after confirming the version number, turn the power off For applications using MIDI, MIDI OUT of sequencer and MIDI IN 1 of the
and on again. SD-80 must be connected with the MIDI cable.

1. Turn on the SD-80’s power.

2. Load the song that were saved in the above procedure via the sequencer.
DATA SAVING AND 3. Start replaying the song with the sequencer.
LOADING 4. The “Writing …” message appears on the screen of the SD-80 when the
sequencer ends replaying.

5. Data loading is completed when the “Completed” message appears.

Necessary items
· Computer equipped with USB terminal, application sequencer and USB cable
Do not turn off the power of the SD-80 as long as the “Writing…” message is
· MIDI sequencer (MC-80 or equivalent) and MIDI cable
displayed.
If the power is turned off, the board memories may be destroyed.

Preparation for using computer Note that the main board must be replaced in this case.

* Do not turn off the SD-80’s power while opening applications on Computer.
Otherwise, computer operation becomes unstable.
Close all applications before turning off the SD-80’s power.
RESTORING FACTORY
1. See the start-up manual of the SD-80 and install the SD-80 USB driver on SETTINGS
the computer to be used.
* After factory resetting, all data in the user’s area is erased.
Back-up the user’s area as instructed in “DATA SAVING AND LOADING”
Installation is not required on a computer (OS) on which the driver has already before factory resetting.
been Installed. 1. Turn on the SD-80’s power.
(But if you reinstall the OS, you need to reinstall the driver as well).
2. Press the [SYSTEM] button to open the SYSTEM setting screen.
2. Connect the SD-80 to the computer with the USB cable.
3. Press the [PAGE>] button until the [Factory Reset] screen appears.

Do not connect any USB device other than the SD-80.

3. Open the [Start] of Windows, [Settings], [Control panel], [Multi-media

properties] and [MIDI setting] boxes. Select EDIROL SD-80 PART A for
4. Press the [ENTER] button. Factory resetting is completed when the
the MIDI output. Then, select EDIROL SD-80 PART A for the MIDI
“Completed” message appears.
input.

Do not turn off the power of the SD-80 as long as the “Executing …” message
When using sequencer applications, “EDIROL SD-80 PART A” must be set to
is displayed.
the output and input of MIDI the respective applications.
If the power is turned off, the board memories may be destroyed.
Note that the main board must be replaced in this case.

Make sure that the SD-80 produces the sound when playing the ordinary SMF
(for example, the one attached to Windows).

4. Close all applications and turn off the SD-80’s power. SYSTEM SOFTWARE
UPDATING PROCEDURE
DATA SAVING
Updating is done by using the SMF file. Updating can be done by any of the
The SD-80 and the computer must be connected with the USB cable. following two methods:
For applications using MIDI, MIDI IN of the sequencer and MIDI OUT 1 of the 1. By USB
SD-80 must be connected with the MIDI cable.
2. By MIDI
1. Turn on the SD-80’s power and set the sequencer to recording standby
mode.

12
 May.2002

When using USB

Be sure to perform factory resetting after updating.
Necessary items
· SD-80 and AC power cord
· Computer equipped with a USB terminal (OS: Windows98/Me/2000) When using the MIDI-IN terminal
· USB cable
· Applications to replay the SMF (recommended: Windows MediaPlayer)
Necessary items
· SD-80 Version Updating Disk (#17041156)
· SD-80 and AC power cord
· Sequencer that can replay the SMF (MC-80, MC-50mkII or equivalent)
UPDATING PROCEDURE · MIDI cable
* Install the USB driver as instructed in “DATA SAVING AND LOADING/ · SD-80 Version Updating Disk (#17041156)
PREPARATIONS FOR USING THE COMPUTER”
* The procedure assumes that Windows MediaPlayer is used for SMF replay.
UPDATING PROCEDURE (BY MIDI)
* Updating may not be done properly if an application other than Windows
MediaPlayer is used. 1. Connect MIDI OUT of the external sequencer and MIDI IN 1 of the SD-80
with the MIDI cable.
* Do not turn off the SD-80’s power while applications using the SD-80 are open.
Otherwise, computer operation becomes unstable. 2. While holding down the [SYSTEM], [PAGE <] and [PREVIEW] buttons,
turn on the power. The “Program Updater” message appears. Keep
Close all applications being used on the SD-80 before turning off the unit’s
holding down these buttons until the next screen appears.
power.
fig.2-1_65
1. While holding down the [SYSTEM], [PAGE <] and [PREVIEW] buttons,
turn on the power. The “Program Updater” message appears. Keep
holding down these buttons until the next screen appears.
fig.2-1_65

3. Press the [PART<] button to open the “Updating by MIDI” screen.

fig.2-1b_65

2. Press the [PART>] button to open the “Update by USB” screen.

fig.2-1a_65

4. Press the [ENTER] button. The “Waiting …” message appears, indicating

that the unit is waiting to receive MIDI data.
fig.2-2_65

3. Start the Windows MediaPlayer, and open the updating SMF

“f00001.mid” for USB on the SD-80 Version Updating Disk.

4. Press the [ENTER] button. The “Waiting …” message appears, indicating

that the unit is waiting to receive MIDI data. 5. Replay the “f00001.mid” file on the SD-80 Version Updating Disk using
fig.2-2_65 the external sequencer. The screen shows the progress during updating.
The “Receiving …” message appears during the SMF replaying to
indicate that the SD-80 is in receiving mode.
fig.2-3_65

5. Updating starts when the computer replays the SMF for updating. The
screen shows the progress during updating. The screen shows “Receiving
…” during SMF replaying to indicate that the SD-80 is in receiving mode.
fig.2-3_65 6. When replaying of one file is completed, the “Waiting …” message
appears. Replay the remaining SMF files in numerical order.
* The SMF for MIDI updating (f00001.mid - f00032.mid) are saved on the SD-80
Version Updating Disk.
* For sequencers that can perform chain-play, (e.g.MC-80) continuous replay in
numerical order makes updating easier

Do not turn off the power of the SD-80 during updating.

If the power is turned off, the board memories may be destroyed.
Do not turn off the power of the SD-80 during updating.
Note that the main board must be replaced in this case.
If the power is turned off, the board memories may be destroyed.
Note that the main board must be replaced in this case.

7. When the “COMPLETE! Please Power OFF.” message appears, turn off
When replaying the SMF, be sure to replay from the top of the file.
the power of the SD-80.
6. When the “COMPLETED! Please Power OFF.” message appears on the
8. Conduct factory resetting as instructed in “RESTORING of FACTORY
screen, turn off the SD-80’s power.
RESETTING”, then turn off the power.
7. Remove the USB cable from the SD-80.
9. Perform the operations described in “Checking the version number”, and
8. Conduct the factory resetting as instructed in “RESTORING FACTORY confirm that updating is correctly completed by checking the version
SETTING”, then turn off the power. number.
9. Perform the operations described in “Checking the version number”, and
confirm that updating is correctly completed by checking the version
number.
Be sure to perform factory resetting after updating.

13
 SD-80

Actions to be taken when an TEST MODE

error occurs
When one of the following error messages appears, turn off the power of the
SD-80, take the actions for the respective error as follows, and restart updating. Necessary items
LOADING incomplete · Headphones
Cause: · Two MIDI cables
Part of the updating file was not loaded properly. · Monitor speaker (with built-in amplifier)
Action: · A device (DAT recorder, Roland UA-30 or equivalent) equipped with digital
Turn off the power of the SD-80. Then turn it on again and restart updating. INPUT terminals (optical or coaxial)
MIDI block chksum
MIDI SysEX chksum
Cause: Selecting the Test Mode
Checksums of the exclusive messages received disagreed.
Connection between the USB cable and the MIDI cable may be incomplete. The test mode can be selected by turning on the power while holding down
the [INST], [PART>] and [SHIFT] buttons.
The currently used SMF replay application may not output data properly.
Keep holding down these buttons until the version number appears.
The currently used MIDI sequencer may not output data properly.
Action (by USB) * This operation is the same as for checking the version number.
Check if the USB cable is broken, or insecurely connected. * To end the test mode, turn off the SD-80’s power.
If a similar message appears, change the SMF replay application.
Action (by MIDI) :
Check if the MIDI cable is broken, or insecurely connected. Test item list
If a similar message appears, change the sequencer.
The test mode items are as follows.
MIDI FIFO full
When one test ends, press the [PART>] button to go to the next test item.
MIDI buffer full
To go back to the previous test, press the [PART<] button.
Cause:
1. Version check
Since a large amount of MIDI data was received in a short time, processing
2. Device check
could not be done.
3. MIDI check
Action:
4. LCD check
Check if a large amount of MIDI data was sent in a short time.
5. SW/LED check
MIDI overrun
6. Encoder check
MIDI framing
7. Sound check
MIDI parity
8. Effect check
MIDI hardware break
9. Factory reset
Cause:
MIDI communication was not done properly. * The USB functions cannot be checked in the test mode.
Action: To check the USB functions, install the driver on the personal computer and see
Check if the MIDI transfer rate of the MIDI device connected to the SD-80 is if the SMF can be played correctly.
proper. (See “DATA SAVING AND LOADING” for the driver installation procedure).
If an error message appears even after the above action, there may be a
problem with the SD-80’s CPU Check the CPU circuit and related circuits of
the SD-80. TEST ITEM DETAILS
FLASH Vpp low
1. Version check
Cause:
The version of the program ROM appears.
The memory (IC3) write voltage on the main board is low.
The version number appears at the bottom left of the screen.
Action:
fig.3-1_70
Check the IC3 circuit and related circuits.
FLASH ID code
Cause:
Part of the memory (IC3) on the main board is wrong.
Action:
2. Device check
Replace it with the correct one (#******** LH28F160BJE-BTL80).
In this test item, the following ICs are checked automatically. The check
FLASH protected results appear on the screen.
FLASH lock
Cause:
Device names and numbers on the main board
The memory (IC3) on the main board is in write protected status.
Flash Memory IC3
Action: Wave ROM A IC28
Check if the No.13 and 14 pins of the IC3 are at the high voltage level (3.3 Wave ROM B IC29
V). XV #1 IC19,IC26
If the voltage is properly controlled, it is possible that IC3 is broken. XV #2 IC27,30
fig.3-2_70

14
 May.2002

3. MIDI check fig.3-5a_65

Check if MIDI communication is done properly.

1. Set the switch on the back of the SD-80 to “OUT 2”.
2. Connect MIDI IN 1 to MIDI OUT 1 of the SD-80 and MIDI IN 2 to MIDI
OUT 2 with the MIDI cable, respectively.
3. After pressing all the switches, check that the LCD displays point
3. If communication is done properly, the following image appears.
symbols only, and that all the LEDs are out.
fig.3-3_70
fig.3-5b_65

4. Set the switch on the back of the SD-80 to “IN 1 THRU”. The following
6. Encoder check
image appears.
fig.3-3a_70
In this test, the LCD displays the value proportional to the angular position of
the [VALUE] knob. At the beginning of the test, the displayed value is 0. Turn
the [VALUE] knob clockwise to increase the displayed value and to make the
tone generator produce the sound. Then, turn the [VALUE] knob
counterclockwise to decrease the displayed value. Check the output sound
through the headphones to see if chattering occurs.
* Change the switch on the back of the SD-80 to “OUT 2” after completing the fig.3-6_65
check.

4. LCD check
Perform the tests for the following four display patterns. Shift the pattern
using the [PAGE<] and [PAGE>] buttons. Shift the test pattern to the previous
1. Turn the encoder clockwise to increase the value displayed on the LCD
one or the next one by pressing the [PAGE<] or [PAGE>] button, respectively,
and to make the tone generator produce the sound. Make sure that the
to perform tests for the four patterns.
fig.3-4_70
displayed value changes proportional to amount the encoder is rotated.
(Change the value from 0 to 23). And check the out put sound.
2. Turn the encoder counterclockwise to decrease the value displayed on the
LCD and to make the tone generator produce the sound. (Change the
value from 23 to 0)
fig.3-4a_70

If chattering occurs, for example, one click may make two sounds or more. and
the clockwise-sound may be produced when the encoder is rotated
counterclockwise. In this test, make sure that the above errors do not occur.
fig.3-4b_70
7. Sound check
In this test, check the DA converter and L and R separation of the stereo output
signals by producing the sound with the built-in tone generator.
Check that no sound distortion occurs and that there is no mixing of the right
fig.3-4c_70 and left signals.
Since the same signal is output to all of the OUTPUT 1/2 and DIGITAL OUT
terminals, change the speaker connections to check all output terminals.
For DIGTAL OUTPUT, connect the output of the external device to the
speaker to check. Change the connection of the optical and coaxial cable inputs
fig.3-4d_70
of the external device to check both inputs.
fig.3-7_65

Check that all the LCD dots remain on all the time or off all the time during the
test. 1. Connect the L and R of OUTPUT to the respective speakers. Connect the
Check that pattern contrast varies when the [VALUE] knob is rotated DIGITAL OUTs to the external device.
clockwise and counterclockwise. Then, check if the pattern can be identified 2. Press the respective buttons of output channels to produce a sine wave
when the contrast is set at maximum and minimum. sound.
* When the LCD check ends, contrast returns to the standard value.

5. SW/LED check Output button

L ch. [INST]
In this test, all LEDs on the front panel are turned on . (The LCD screen
R ch. [SYSTEM]
displays boxes located so as to represent the switches at their respective
Both channels [EFFECTS]
relative positions.) The LCD screen displays ten boxes that mean swithes on
the front panel. 3. Change the OUTPUT terminals. Conduct (2.) above to check the newly
connected terminals. Check the headphones to which the same signals
are output.

1. Check that the LCD screen displays box symbols only and all LEDs are the VOLUME control changes the amplitude of the signals output to the
on. headphones and OUTPUT 1. OUTPUT 2 and DIGITAL OUT have no volume
2. Press the switches one by one to check that the box symbol on the LCD adjustment.
changes to a point symbol. And check if the LED for the pressed switch
8. Effect check
goes out.
The effect test is conduct on the built-in sound source.
Press a blinking button on the SD-80 to produce the sound effect. Check this

15
 SD-80

sound by listening to it through the headphones.

Press the same button to stop the effect.
fig.3-8_65

MFX
Press the [INST] button to send a snare sound at an interval of 2.5 seconds
from the power source. Make sure that a delayed sound is heard after the
original snare sound.
SYSTEM EFFECT (Delay)
Press the [EFFECTS] button to send a castanets sound at an interval of 2.5
seconds from the power source. Make sure that a delayed sound panning
right and left, is heard after the original castanets sound.
SYSTEM EFFECT (Reverb)
Press the [SYSTEM] button to send a snare sound at an interval of 2.5
seconds from the power source. Make sure that the snare sound
reverberates.

9. Factory reset
If all the test results are OK, initialize the system parameters as the last step.
Press the blinking [PREVIEW] button to start initialization. Initialization is
completed when the “Complete!” message appears.
Turn off the SD-80’s power to end the test mode.
fig.3-9_65

16
 May.2002 SD-80

BLOCK DIAGRAM
fig.block
ig.cable

J K7 JK 3 J K4 J K5 J K6 S W2 J K2 CN 2 V R1

J K8

J K9
J K10

J K12
J K11

IC6 N JM4565D
W IR IN G
4X200-P 2. 0-PH R-PH R-F
02342012

C N6

C N4
J AC K1 B OA RD V OL UME B OA RD J AC K2 B OA RD
AS S Y72120490 AS S Y72120534 AS S Y72120501
C N3 C N5 C N7

W IR IN G W IR IN G
B NC D-P=1.00-K -18-60 6X200-P 2. 0-PH R-PH R-F 8X150-P 2. 0-PH R-PH R-F
02903067 02343245 02343545

C N6 C N8 C N7
MAIN B OA RD
AS S Y72120445
Bind the wiring between MB and J1B, and the wiring between VB and J2B as shown in
the figure. Fix them onto the bottom chassis with tape.

IC35 U PC4570G 2

IC31 U PC4570G 2
Otherwise, OUTPUT terminal noise may increase and there may be a danger of the
wiring touching the power unit.

res et, c lock

s ubCP U
C PU IC17

P C M1 7 1 6 E

P C M1 7 1 6 E
IC2 M37641M8-

T C9 2 7 1 FS

01897201

01897201
01785178
H D6417706 137FP

D AC

D AC
c ontras t

I C3 4

I C3 2
I C3 3
D IT
02903723 02902867
L evel C onve rte r
IC10,IC11, IC 12

Tone
generato r
IC27
T C223C660CF
F la sh 01455956
S DR AM memory
IC4,IC6 IC3 D RA M
LC381616FT-70-TLM L H28F160BJ E IC30
IC20,IC22,IC23,IC24,IC25

03015212
GM71C18163CJ-6
L evel C onve rte r

02450401

D RA M Mas kR OM
IC28
IC26 03010612
GM71C18163CJ-6
IC29
02450401 W IR IN G
03010623 +3. 3V +1. 9V +5V
12X100-P 2. 0-PH R-PH R-F
02344001
Tone D C-DC
generato r c onve rte r J K1
IC1,Q 1
IC19
T C223C660CF

C N1

C N1
01455956 +15V

P OW ER
-15V
S upply unit
B OA RD 1
C N3 C N5 C N4 A 1D U2L3B104
02457745

W IR IN G B NC D-P=1.00-K -16-120 B NC D-P=1.00-K -14-200

4X50-P 2. 0-PH R-PH R-F 02908823 02239390
02341967

C N10 C N9 C N8

E NC OD ER B OA RD P OW ER AS S Y S W1
AS S Y72120545 L CD S W matr ix ( 3s ca nx4data ) 72125767
R CM2072M-B
02780067 L ED matr ix ( 3s ca nx3data )
E N1 L CD B OA RD P A N EL B OA RD
AS S Y72120523 AS S Y72120512

17 18
 May.2002

CIRCUIT BOARD (MAIN BOARD)

fig.mb-sch1

19
 SD-80

CIRCUIT BOARD (JACK SHEET)

fig.mb-sch1

20
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 1/7)

fig.mb-sch1

MAIN BOARD BLOCK DIAGRAM

LEVEL CONVER T
C PU Block B loc k USB Block
12MHZ 12MHZ

3D[0..15] D[0..15]
3D[0..15] 3A[1..8] 3D[0..15] D[0..15] A[1..8] D[0..15]
P OWER BLOCK 3A[1..8] 3A[1..8] A[1..8] A[1..8]
3A24 3A24
3XR D 3XR D XRD XRD
3XWRLU 3XWRLU XWR XWR

XS1 XS1
from P OWER 3XC SIPC 3XC SIPC XS0 XS0
AS S Y D +5 IBF IBF
OBF OBF
C N1 R1 R2 3XC ST G 3XCST G
B12B-PH-S M3-T B 1k 1k XCS V0
XCS V1
1
1 3XWAIT 3XWAIT
2

3
2 3XINT V1 3XINT V1 XINTV0
3
3 C1 D +1. 9 D +3. 3 IC1 R106 3XINT V0 3XINT V0 XINTV1
4

S1

S2
4
4 150u/6.3V M62292FP 220 Q1 3IB F 3IB F XWAIT
5
5 OS-CON R3 F W111 3OB F 3OB F
6 8 1 4

G ND VCC
6 1k IN1 C OUT1 G2 X RST T G
7 2
7 (D) G1 XENDIT USB DN
8 5 3

RESET
8 IN2 C OUT2 3AMUT E 3AMUT E AMUTE USB DP

D1
D1
D2
D2
9
9 + 15 3XR ST DAC 3RS TDAC XRS TDAC V BUS

CD
10 R107
10 R4 C2 R5 220 3XR ST T G 3RST T G
11
11

7
8
5
6
12 D NIU NIU 1k
12 3XR ST 3XR ST CP U 3XR ST CP U XRS TC PU X RS TC PU
7
6
2
3XR ST XRS T XRS T
C ONTR AS T 2_LEV CNV 4_USB
D
R 112 3XR ST 3XE NC A LEV CNV USB
- 15
680 3XE NC B
A
1W L1 3XE NC SW
D +1. 9
TONE G ENER ATOR #0
T P1 100uH L2
1 47uH D +3. 3 3RXD2 B loc k
3RXD1

2
3TXD2 5_T G0

2
C3 D1 3TXD1 T G0
0.1u R B051L-40 C6 D2 1_C PU
330u/4V R B051L-40 C7 C PU D[0..15]
1

OS-CON 150u/6.3V
OS-CON A[1..8] 384FS

1
XRD S YNC
D
XWR
V 0V 1S CK V 0V 1S D[0..5]
D D
V 0V 1S D[0..5] V 1V 0S D[0..5]
V 1V 0S D[0..5]
V 1V 0S CK

3WD[0..15]
XCS V0 3WD[0..15] 3WA[0..22]
3WA[0..22]
3XWCS R1
AUDIO Bloc k XINTV0 3XWCS R0
XWAIT 3XWOE

XRS TDAC XWOE

AMUTE XWC S0 WD[0..15]
XENDIT WD[0..15] WA[0..23]
WA[0..23]

XRSTTG XWB RE Q
XWB AC K
O UT 1 OUT 1
O UT 2 OUT 2
O UT 3 OUT 3
B CK B CK
256FS 256FS
XLR CK 1 XLR CK 1
LRC K2 LRC K2

S CAN[0..2]
LED[0..2] S CAN[0..2]
XSW[0..3] LED[0..2]
DOUT XSW[0..3]

LE
LP[0..7] RS
7_AUDIO LP[0..7]
AUDIO

INTER FACE Block TONE G ENER ATOR #1

B loc k

D[0..15]
A[1..8]
DOUT USB DN XWB AC K
USB DP XRD XWB RE Q
V BUS XWR
WA[0..23]
WD[0..15]
XCS V1 XWC S0
XWOE
XINTV1
3TXD1 XWAIT 3XWOE
3TXD2 3XWCS R0
3RXD1 3XWCS R1
3RXD2 3WA[0..22]
3WD[0..15]
3XE NC SW S CAN[0..2]
3XE NC B LED[0..2]
3XE NC A XSW[0..3] XRSTTG V 1V 0S CK
C ONTR AS T V 1V 0S D[0..5]
LE V 0V 1S D[0..5]
RS V 0V 1S CK
LP[0..7]
S YNC
384FS
3_INT ER FACE
INT ER FACE

NOTE : "NIU" means "Not In Use."

6_T G1
T G1

21 22
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 2/7)

fig.mb-sch2

C PU Block
3A24
3A[1..8] LEVEL _C ONV.
B loc k
3D[0..15]

16 1
3RDWR 15 2 83 76
3XWRUU R D/WR A25
14 3 82 75 1 16
3XWRUL R A1 WE3/DQMUU/ICIOWR/PT C[2] A24 3A24
13 4 81 74 2 15
3XWRLU 0 WE2/DQMUL/ICIOR D/PT C[1] A23
3XWRLU 12 5 80 72 3 14
3XWRLL WE1/DQMLU/WE A22 R A2 3A21
11 6 79 70 4 13
3XR D WE0/DQMLL A21 22 3A20
3XR D 10 7 78 69 5 12
RD A20 3A19
9 8 77 68 6 11
B S/PT C[0] A19 3A18 3A21
16 1 67 7 10
3XC SIPC A18 3A17
3XC SIPC 15 2 91 66 8 9
3XCST G 14 3 90 C S6/C E1B/PT C[7] A17 65 1 16 3A16
3XCST G C S5/C E1A/PT C[6] A16 D +3. 3 D +3. 3
3RS TDAC R A3 13 4 89 64 2 15 3A15 IC3
3XR ST DAC C S4/P TC [5] A15
3RST T G 0 12 5 88 62 3 14 3A14 3A20 9 45 3D15
3XR ST T G C S3/P TC [4] A14 A19 DQ15/A-1
3XC SR AM R A4 3A13 R A5 R A6 3A19 3D14

10

10
11 6 87 60 4 13 16 43

1
3XC SR OM C S2/P TC [3] A13 22 3A12 10k 10k 3A18 A18 DQ14 3D13
10 7 85 59 5 12 17 41
C S0 A12 3A11 3A17 A17 DQ13 3D12
9 8 58 6 11 48 39
A11 3A10 3A16 A16 DQ12 3D11
LEVEL _C ONV. 101
IOIS16/P TD[5] A10
57 7 10 1
A15 DQ11
36
8 1 100 56 8 9 3A9 3A15 2 34 3D10
B loc k C KE /P TD[4] A9 A14 DQ10

2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
3CK E 7 2 99 55 1 16 3A8 3A8 R A9 22 3A14 3 32 3D9
D +3. 3 R6 3XC AS 6 3 98
C AS U/PT D[3] A8
54 2 15 3A7 3A7 3A13 19 49 1 16 3D15 3A13 4
A13 DQ9
30 3D8
10k 3XR AS C AS L/PT D[2] A7 3A6 3A6 3A12 A11 DQ15 3D14 3A12 A12 DQ8 3D7
5 4 97 53 3 14 20 48 2 15 5 44
R AS U/PT D[1] A6 R A8 3A5 3A5 3A11 A10 DQ14 3D13 3A11 A11 DQ7 3D6
96 52 4 13 32 46 3 14 6 42
R A7 0 R AS L/PT D[0] A5 22 3A4 3A4 3A10 A9 DQ13 3D12 3A10 A10 DQ6 3D5
94 50 5 12 31 45 4 13 7 40
3AMUT E C E2B/PT D[7] A4 3A3 3A3 3A9 A8 DQ12 3D11 3A9 A9 DQ5 3D4
3AMUT E 92 48 6 11 30 43 5 12 8 38
C E2A/PT D[6] A3 3A2 3A2 3A8 A7 DQ11 3D10 3A8 A8 DQ4 3D3
47 7 10 29 42 6 11 18 35
XVP P A2 3A1 3A1 3A7 A6 DQ10 3D9 3A7 A7 DQ3 3D2
108 46 8 9 28 40 7 10 19 33
DRAK1/P TE [3] A1 3A6 A5 DQ9 3D8 3A6 A6 DQ2 3D1
107 45 27 39 8 9 20 31
WPF R DRAK0/P TE [2] A0 3A5 A4 DQ8 3D7 3A5 A5 DQ1 3D0
106 24 12 1 16 21 29
DAC K1/P TE [1] 3D31 3A4 A3 DQ7 3D6 3A4 A4 DQ0
105 5 8 9 23 11 2 15 22
D +3. 3 DAC K0/P TE [0] D31/P TB [7]
6 7 10 3D30 3A3 22
A2 DQ6
9 3 14 3D5 3A3 23
A3
3XWAIT D30/P TB [6] 3D29 3A2 A1 DQ5 3D4 3A2 A2
3XWAIT 104 7 6 11 21 8 4 13 24
WAIT D29/P TB [5] R A11 3D28 A0 DQ4 3D3 3A1 A1 D +3. 3
103 8 5 12 6 5 12 25 10
B RE Q D28/P TB [4] 22 3D27 DQ3 3D2 A0 NC
102 9 4 13 5 6 11
B AC K D27/P TB [3] 3D26 3XC SR AM DQ2 3D1 3XC SR OM
10 3 14 18 3 7 10 26 13
D +3. 3 XAUDS YNC 113
D26/P TB [2]
12 2 15 3D25 3XR AS 17
CS DQ1
2 8 9 3D0 3XWRLL 11
CE V PP
37
AUDATA3 AUDSY NC /P TF [4] D25/P TB [1] 3D24 3XC AS R AS DQ0 3XR D WE V CC
8 1 112 14 1 16 16 28
R A12 AUDATA2 AUDATA[3]/P TF [3] D24/P TB [0] 3D23 3RDWR C AS R A10 22 OE C9
7 2 111 15 8 9 15 47
10k AUDATA1 AUDATA[2]/P TF [2] D23/P TA[7] 3D22 3XWRLU WE B YT E 10u/16V
6 3 110 16 7 10 36 1 3XR ST 12
AUDATA0 AUDATA[1]/P TF [1] D22/P TA[6] 3D21 3XWRLL UDQM V DD RP
5 4 109 17 6 11 14 25 14 46
AUDATA[0]/P TF [0] D21/P TA[5] R A13 3D20 3CK E LDQM V DD D +3. 3 WP G ND
D20/P TA[4]
18 5 12 34
C KE VDDQ
44
D +3. 3
P OWER 15
R Y/BY G ND
27
16 1 XAS EMD0 122 20 4 13 22 3D19 3CK O 35 38
15 2 XAS EB RK AK 121
ASE MDO D19/P TA[3]
22 3 14 3D18 C LK VDDQ
13 BLOCK LH28F160BJ E-B-BT L90@ C8 C212
T DO ASE BR KAK/PT F[6] D18/P TA[2] 3D17 VDDQ D +3. 3 0.1u 0.1u Q8
14 3 120 23 2 15 7 D
R A14 X TR ST T DO/P TF [5] D17/P TA[1] 3D16 VDDQ C213 0.1u 2SA1530A
13 4 119 24 1 16 33
10k TMS T RS T/PT G[3] D16/P TA[0] 3D15 3D15 NC
12 5 118 26 8 9 37 3 2
T CK T MS /P TG [2] D15 3D14 3D14 NC C 16
11 6 116 28 7 10
T DI T CK /P TG [1] D14 3D13 3D13 10u/6.3V R 89
10 7 114 29 6 11 4 D

5
C 17 470p T DI/P TG [0] D13 R A15 3D12 3D12 V SS Q 10k
9 8 30 5 12 10
D12 V SS Q

1
127 31 4 13 22 3D11 3D11 41 WPF R 2 4 R 90
C AP 2 D11 3D10 3D10 V SS Q C 10 C 12 C 14 IC37 R 91 10k
32 3 14 47 D
124 D10 33 2 15 3D9 3D9 V SS Q 26 0.01u 0.01u 0.01u D T C7SH04FU 3.3k
C AP 1 D9 3D8 3D8 V SS C 11 C 13 C 15 XVP P

3
34 1 16 50
C 18 470p D8 3D7 3D7 V SS 0.01u 0.01u 0.01u
D 2 35 8 9
XTAL2 D7 3D6 3D6 IC4
36 7 10
C 19 D +3. 3 D +3. 3 R7 D6
38 6 11 3D5 3D5 LC3816161ET -70
0.01u 10k D5 R A16 3D4 3D4 or equivarent
40 5 12 D
D4 22 3D3 3D3 exept HY57V161610
3 41 4 13
E XTAL2 D3 3D2 3D2
42 3 14
IC5 D2 3D1 3D1 D +3. 3
43 2 15
5

T C7SH04FU D1 3D0 3D0 D +3. 3 S W1A

D 131 44 1 16
XTAL D0 SSSS 222-01-A
12MHZ 2 4
D +3. 3 R A17 R A18 NIU

10

10
1

1
USB R8 100 175 10k 10k 11
AVC C
3

R 93 132 XAS EMD0 12 13

B loc k NIU E XTAL C 20
R9 100 0.1u R A19 22 D +3. 3 21
D +3. 3

2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
D 3CK O 138 170 3A13 19 49 1 16 3D31 22 23
C KIO AVS S 3A12 A11 DQ15 3D30
176 20 48 2 15
AVS S 3A11 A10 DQ14 3D29 R 10 10k S W1B R 11 NIU
136 D 32 46 3 14
8
7
6
5
4
3
2
1

IRQOUT /P TE [7] 3A10 A9 DQ13 3D28 SSSS 222-01-A

135 31 45 4 13
R A20 134 T CLK/PT E[6] 150 3A9 30
A8 DQ12
43 5 12 3D27 NIU D
10k S TATUS1/P TE [5] V CC 3A8 A7 DQ11 3D26
133 117 29 42 6 11
S TATUS0/P TE [4] V CC D +1. 9 3A7 A6 DQ10 3D25
73 28 40 7 10
10

12
13
14
15
16
11

V CC A5 DQ9
9

147 21 3A6 27 39 8 9 3D24 36

3XE NC A C TS 2/IR Q5/S CP T[5] V CC A4 DQ8 36
INTER FACE 146 3A5 24 12 1 16 3D23 AUDCK 18
3RXD2 R XD2/SC PT [2] A3 DQ7 18
145 3A4 23 11 2 15 3D22 35
B loc k 3RXD1 R XD0/SC PT [0] A2 DQ6 35
144 C 25 3A3 22 9 3 14 3D21 17
3XE NC B R TS 2/SC PT [4] A1 DQ5 17
143 19 3A2 21 8 4 13 3D20 34
3XE NC SW S CK 2/SC PT [3] V SS A0 DQ4 34
142 71 470u/6.3V 6 5 12 3D19 3XR ST CP U 16
3TXD2 T XD2/SC PT [2] V SS DQ3 16
141 115 5 6 11 3D18 33
S CK 0/SC PT [1] V SS C 22 C 24 3XC SR AM DQ2 3D17 33
3TXD1 140 130 D 18 3 7 10 15
T XD0/SC PT [0] V SS 0.01u 0.01u 3XR AS CS DQ1 3D16 15
148 17 2 8 9 32
V SS C 21 C 23 3XC AS R AS DQ0 XAS EB RK AK 32
C ONTR AS T 16 14
R A22 0.01u 0.01u 3RDWR C AS R A21 22 14
D 15 31
10k 3XWRUU WE T DO 31
158 36 1 13
D +3. 3 8 1 174
VC C Q
139 3XWRUL 14
UDQM V DD
25 30
13
AN[3]/DA[0]/P TJ [3] VC C Q 3CK E LDQM V DD T DI 30
7 2 173 95 34 44 12
R 12 AN[2]/DA[1]/P TJ [2] VC C Q 3CK O C KE VDDQ D +3. 3 12
6 3 172 86 35 38 29
10k AN[1]/P TJ [1] VC C Q C LK VDDQ X TR ST 29
5 4 171 63 13 11
AN[0]/P TJ [0] VC C Q VDDQ 11
51 7 28
T P2 D VC C Q 39 33
VDDQ TMS 10
28
R 13 VC C Q D +3. 3 NC 10
1 149 27 37 27
0 RESETM VC C Q NC T CK 27
157 13 9
NMI VC C Q C 32 9
3XR ST CP U 165 4 26
RESETP V SS Q 10u/6.3V 26
166 10 8
R 14 CA C 42 V SS Q 8
41 25
C 43 D +3. 3 10k D 11 10u/6.3V V SS Q
47 7
25
NIU VS S Q V SS Q C 27 C 29 C 31 7
LEVEL _C ONV. 162
ADT RG /P TG [5] VS S Q
25
V SS
26 24
24
161 37 50 0.01u 0.01u 0.01u D XAUDS YNC 6
B loc k D 160
DRE Q1/P TH[6] VS S Q
49 C 34 C 36 C 38 C 40 D
V SS C 26 C 28 C 30 23
6
R 15 AUDCK DRE Q0/P TH[5] VS S Q 0.01u 0.01u 0.01u 0.01u IC6 0.01u 0.01u 0.01u AUDATA3 23
159 61 5
10k AUDCK /P TG [4] VS S Q C 33 C 35 C 37 C 39 C 41 LC3816161ET -70 5
84 D 22
VS S Q 0.01u 0.01u 0.01u 0.01u 0.01u or equivarent AUDATA2 22
93 4
VS S Q exept HY57V161610 4
155 137 21
IRQ4/PT H[4] VS S Q AUDATA1 21
3OB F 154 156 3
IRQ3/IR L3/P TH[3] VS S Q D +1. 9 D +1. 9 3
3IB F 153 20
IRQ2/IR L2/P TH[2] AUDATA0 20
3XINT V1 152 D 2
IRQ1/IR L1/P TH[1] 2
3XINT V0 151 128 19
IRQ0/IR L0/P TH[0] VC C -PLL2 19
123 1
VC C -PLL1 1
C 44 C 45 C N2
D +3. 3 0.01u 0.01u DX10M-36S
169 125 NIU
MD5 VS S P
- LL1
168 126 D
MD4 VS S P
- LL2
167
MD3 D +1. 9
164
MD2
129
MD1
163 1 D
MD0 V CC -R TC
C 46
D 0.01u
4
VS S R
- TC

IC2 D

HD6417706F133

NOTE : "NIU" means "Not In Use."

23 24
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 3/7)

fig.mb-sch3

LEV EL CONV ER TE RB lock INT ER FACE BLOC K

D +5

USB D +3. 3 Q2
X RS TC PU

2
IC7B DTB 113ZK

14
B lock IC7A LV00A 1
P OWER LV00A 5 C 57 C 76 IC15G C 58 L3 NIU
1 6 10u/16V 0.1u LV04A 0.1u
B lock 3XR ST CP U

3
3 4

7
2 Q3
3XR ST

2
DTB 113ZK
D 1
L4 NIU
3AMUTE
D +3. 3
USB

3
IC7C
LV00A C 48 D +5
XRS T B lock Q4

2
9 0.1u DTB 113ZK
3RST T G
8 1
10 TONEG enerator L5 NIU
XRST T G

20
B lock

3
3RS TDAC D
11 9

VCC
IC7D B8 A8
12 8
LV00A B7 A7 IC15A LV04A R 19 390
13 7 AMUTE
B6 A6 LED2
12 14
B5 A5
6 XENDIT ANALOG 1 2
11 15 5
13 16
B4 A4
4
XRS TDAC B lock IC15B LV04A R 20 390
B3 A3 LED1
3XWRLU 17 3 3 4
B2 A2
3XR D 18
B1 A1
2 TONEG en.#1
IC15C LV04A R 21 1k C N4
19 B lock LED0 5 6 14FMN-BMT-A-TF

G ND
IC9 G
1 LED[0..2] 1
V HC T245A DIR 1
2
IC15D LV04A 2
3

10
S CAN[0..2] 3
S CAN2 9 8 XSC AN2 4
C 51 D +5 R A26 5
4
0.1u D
XSW[0..3]
IC15E LV04A 1k 6
5 to PANEL
6
S CAN1 11 10 XSC AN1 8 1 7
7 boa rd
7 2 8
IC15F LV04A 8
20

D 6 3 9
S CAN0 13 X 12 S CAN0 5 4 10 9
3A[1..8] 10
3A8 11 9 A8 8 9 A8 11
VCC

3A7 B8 A8 A7 A7 R A27 11
12 8 7 10 12
3A6 B7 A7 A6 A6 1k 12
13 7 6 11 13
3A5 B6 A6 A5 A5 XSW3 13
14 6 5 12 8 1 14
3A4 B5 A5 A4 A4 XSW2 14
15 5 4 13 XWR 7 2
3A3 B4 A A4 3 A3 XSW1
16 4 3 14 6 3
3A2 B3 A A3 2 A2 XSW0
17 3 2 15 XRD 5 4
3A1 B2 A2 A1 A1
18 2 1 16
B1 A1
A[1..8]
19 XGATE R A24
G ND

IC11 G NIU
1
V HC T245A DIR
10

D +5 C103 C 63 C 65 C 67 C 69 C 71 C 73 D
10u/16V 1000p 1000p 1000p 1000p 1000p 1000p
D C 62 C 64 C 66 C 68 C 70 C 72 C 74
1000p 1000p 1000p 1000p 1000p 1000p 1000p
C 49 C 50
0.1u D +3. 3 0.1u

D +5
24

3D[0..15] D D
1

D[0..15]
3D15 D15 D15 C N5
VC C A

10 14 8 9 TONE
V CC B

3D14 A8 B8 D14 D14 R A28 R 25 R 24 16FMN-BMT-A-TF

9 15 7 10
3D13 8
A7 B7
16 D13 6 11 D13 G ENER ATOR #1 22 22 22 1
3D12 A6 B6 D12 D12 1
7 17 5 12 RS 2
3D11 A5 B5 D11 D11 2
6 18 4 13 LE 3
3D10 A4 B4 D10 D10 LP0 3
5 19 3 14 16 1 4
3D9 4 A3 B3 20 D9 2 15 D9 LP1 15 2 5 4
A2 B2 LP[0..7] 5
3D8 3 21 D8 1 16 D8 LP2 14 3 6
A1 B1 D +5 LP3 6
13 4 7
XGATE R A23 LP4 7
22 12 5 8
G NIU LP5 8
16

2 11 6 9
G ND
G ND
G ND

DIR LP6 9
23 10 7 10
NC IC10 LP7 10
9 8 11
VCC

T C74LV XC3245FS C 56 IC13C 11

12
12
13
11

0.1u V HC T139A 12
13
G ND

13
14
15 14
C ONTR AS T 15
D 16
16
8

C PUBlock R 26
C 52 C 53 D 100
0.1u D +3. 3 D +5 0.1u
D +3. 3

3
D +3. 3 C 77
24

D D 1 2
1

0.1u
3D7 10 14 D7 8 9 D7 D +5 DA3
V CC A
V CC B

3D6 9 A8 B8
15 D6 7 10 D6 D +3. 3 C N6 D MA147-(TX)
3D5 A7 B7 D5 D5 R 22 NIU 18FMN-BMT-A-TF C 78 C 80 C 82 C 84 C 86 C 88
8 16 6 11 D
3D4 A6 B6 D4 D4 1000p 1000p 1000p 1000p 22p 10u/16V
7
A5 B5
17 5 12 AUDIO DOUT 1
1
3D3 D3 D3 C 79 C 81 C 83 C 85 C 87
14

6 18 4 13 2
3D2 5
A4 B4
19 D2 3 14 D2 B lock R A49 3
2 1000p 1000p 1000p 1000p 1000p
3D1 A3 B3 D1 D1 NIU 3
4 20 2 15 4
3D0 A2 B2 D0 D0 C 55 IC7E 4
3 21 1 16 5
A1 B1 0.1u LV00A 5
6
R A25 6
22 3RXD1 8 1 7
G NIU 7
2 C PU 7 2 8
G ND
G ND
G ND

3XR D DIR 3TXD1 8

7

23 6 3 9
NC IC12 B lock 3RXD2
5 4 10
9
D +3. 3 3TXD2 10
T C74LV XC3245FS D 11
12
13
11

11
12
12
USB DN 13
5

13
14
14
3XC SIPC 1 D USB USB DP 15
15
4 C 54 16
2 0.1u B lock 17
16
3XC ST G V BUS 17
18
IC14 18 D +3. 3
T C7SH08FU
3

D D
D +5 to J AC K1
C 47
IBF boa rd

5
6
7
8
0.1u D +3. 3
USB
R A50
3 7 R 16
OBF B lock 10k
B Y3 10k IC16F IC16A R A51
20

2 6 D
A Y2

4
3
2
1
5 USB LV14A LV14A 1k
1
Y1
4
XS1
9 11 12 13 2 1 5 4 1 to
VCC

3XC SIPC G Y0 XS0 B lock 3IB F A8 B8 XINTV1 3XE NC A 1

IC13A
3OB F 8
7
A7 B7
12
13 C PU
6
7
3
2
2
3
2 E NCODER
3XINT V1 A6 B6 XINTV0 3
V HC T139A
3XINT V0 6
5
A5 B5
14
15 B lock
IC16C
LV14A
IC16B
LV14A
8 1 4
4 boa rd
3XWAIT A4 B4 XWAIT
13 9 4 16 6 5 4 3 C N3
B Y3 A3 B3 3XE NC B
14 10 3 17 TONEG enerator C 75 C 60 B04B-PH-S M3-T B
3A24 A Y2 A2 B2 D +3. 3
11 2 18 NIU 0.1u
15
Y1
12
XCS V1 A1 B1 B lock D
3XCST G G Y0 XCS V0

14
19 D 8 9 10 11
G ND

OE 3XE NC SW
D IC13B TONEG enerator 1 C 59 D
V HC T139A DIR IC8 IC16D IC16E 0.1u C 61 IC16G
B lock LV245A LV14A LV14A 0.1u LV14A
10

7
D
D

NOTE : "NIU" means "Not In Use."

25 26
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 4/7)

fig.mb-sch4

USB Block
D +5
C5
NIU D +5 C 89
OS-CON 10u/16V

C 91
C 90 0.1u
D 0.1u
C 92
D 0.1u
USB DP
(K) C NV SS
C 93
0.1u D

17

16

74
R 31
USB DN
1.5k R 27 C 94
1k

AVC C

V CC

V CC
INT ER FACE 680P 9 41 S W2A
Q7 R101 C NV SS P 17/AB15 S S S S22-01-A
2 D +5
D 18 42
B lock

3
S S M3J02T 100k LPF P 16/AB14 NIU
43
XPULLUP P 15/AB13
1 1 16 25 44 11
P87/R TS 1 P 14/AB12 C NV SS
2 15 26 45 12 13
P86/C TS 1 P 13/AB11
3 14 27 46
C 95 R A29 P85/URXD1 P 12/AB10 R 95

2
4 13 28 47 21
NIU 10k P84/UTXD1 P 11/AB9 0
5 12 29 48 22 23
P 83/S TXD/RT S2 P10/AB8
6 11 30 49
R 29 R 30 R100 D +5 P82/S RXD/CT S2 P07/AB7 S W2B R102
7 10 31 50 D
33 33 NIU P81/S CLK/UR XD2 P06/AB6 SSSS 222-01-A NIU
8 9 32 51
(D) (D) P80/S RDY/UT XD2 P05/AB5 NIU
52
P04/AB4
70 53 D
USB D+ P03/AB3
71 54
USB D- P02/AB2
72 55
XCV R P OWER /E XT C P01/AB1 R A52 D +5
56
OBF P00/AB0 10k
65
C 96 C 99 P74/OBF 1
66 57 8 9
NIU 0.1u XS1 P73/IBF 1/HLDA P27/DB7
67
P72/S 1 P26/DB6
58 7 10 C PU
59 6 11
D7 75
P25/DB5
60 5 12 B lock
C 97 C 98 D6 P67/DQ7 P24/DB4
D 76 61 4 13
NIU 2.2u/50V D5 P66/DQ6 P23/DB3
LEV EL_C ONV. 77
P65/DQ5 P22/DB2
62 3 14 12MHZ
D4 78 63 2 15
B lock D3 79
P64/DQ4 P21/DB1
64 1 16
D2 P63/DQ3 P20/DB0
OBF 80
D1 P62/DQ2
IBF 1 33
D0 P61/DQ1 P 37/R D R 33
2 34 D
P60/DQ0 P36/W R 0
35
XWR P35/S YNCOUT
XWR 3 36
XRD P57/W (R /W ) P34/P HAIOUT
XRD 4 37
A1 P56/R (E ) P33/DMAOUT
5 38
XS0 P55/A0 P 32
6 39
IBF P54/S 0 P 31
XS1 7 40 XRS TC PU
P53/IBF 0 P30/R DY
XS0 8
P52/OBF 0
P71/HOLD
68 LEV EL_C ONV.
20 69 R 34
21
P44/C NT R1 P70/S OF 10k B lock
P43/C NT R0
10 D D +5
XRS T RESE
T
R 35 14 R 88
0 R 36 330 XIN 100k
X1 1 4 15 22 XPULLUP
24.000MHz XOUT P42/INT 1
D 23
C100 P41/INT 0 D +5
D[0..15] 12 24
NIU C101 C102 P50/XCIN P40/E DMA R 115

3
15p 15p 11 100k
A[1..8] P51/TOUT/XC OUT Q11 1 V BUS
D D 2SC3052

AVS S
D15 INT ER FACE

V SS

V SS
D14 A8

2
D13 A7 R 28 B lock
D12 A6 19 M37641M8-137FP 1M

13

73
D11 A5 R02902867
D10 A4 IC17 R 116 D
D9 A3 100k
D8 A2
D
D D

NOTE : "NIU" means "Not In Use."

27 28
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 5/7)

fig.mb-sch5
D +5 C 4
100u/6.3V
XWB AC K
XWB RE Q
TONE G ENER ATOR #0 BLOC K
C104
XWC S0
0.1u
D +3. 3 WA[0..23]
C106 C105
WD[0..15]
10u/6.3V 0.1u
XWOE
C107
0.1u
C108
0.1u D +5
C109
3WA[0..22]
0.1u
3XWOE
C 110
3WD[0..15]
C111 0.1u
0.1u C 112 R 37 R 38 TONE
C 113 0.1u 10k 10k
0.1u C 114 G ENER ATOR#1
C 115 0.1u S ection
0.1u C 116
C 117 0.1u 3 7
0.1u C 118 2 B Y3
6
0.1u A Y2
5 3XWCS R1
C 119 Y1
D 1 4 3XWCS R0
0.1u G Y0
D IC18A LV139A 13 9

150
170
190
210

105
120
134
160
180
200
220
240
B Y3

14
30
70
90

46
60
80
D 14 10
A Y2
11
C120 Y1
15 12
LED0 4 3 0.1u D +3. 3 G Y0
LED1 5 2 D IC18B
LED2 6 IC20 LV139A
LV245A

20
7 239 D
8 238 D +3. 3
9 237 WA22 11 9 3WA22

VCC
WA21 B8 A8 3WA21

16
10 12 8
WA20 B7 A7 3WA20
11 236 13 7
WA18 B6 A6 3WA18
235 14 6

VCC
WA19 B5 A5 3WA19 C121 IC18C
384FS 13 234 15 5
WA17 B4 A4 3WA17 0.1u LV139A
233 16 4

G ND
R 43 WA8 B3 A3 3WA8
15 232 17 3
22k WA7 B2 A2 3WA7
TONE 16 231 18
B1 A1
2
17 230
G ENER ATOR#1

8
C122 C123 C124 18 229 R A35 19

G ND
9
8
7
6
5
4
3
2
OE
B lock 10u/16V 0.1u 2200p 10k

10
19 1

1
DIR C 125 C126
20 228 D
21 227 WA23 0.1u D +3. 3 0.1u D +3. 3 D R A36

10
D 226 WA22 10k

10

1
XSW0 23 225 WA21 IC22

9
8
7
6
5
4
3
2
XSW1 WA20 LV245A

20

20
24 224 D D D
XSW2 25 223 WA18 D
XSW3 26 222 WA19 WA9 11 9 3WA9 WD9 9 11 3WD9

VCC

VCC
WA17 WA6 B8 A8 3WA6 WD6 A8 B8 3WD6
27 219 12 8 8 12
WA8 WA10 B7 A7 3WA10 WD1 A7 B7 3WD1
28 218 13 7 7 13
WA7 WA5 B6 A6 3WA5 WD14 A6 B6 3WD14
D 29 217 14 6 6 14
WA9 WA11 B5 A5 3WA11 WD8 A5 B5 3WD8
INTER FACE 32 216 15
B4 A4
5 5
A4 B4
15
215 WA6 WA4 16 4 3WA4 WD7 4 16 3WD7
B lock S CAN0 33 214 WA10 WA12 17
B3 A3
3 3WA12 WD0 3
A3 B3
17 3WD0
S CAN1 WA5 WA3 B2 A2 3WA3 WD15 A2 B2 3WD15
34 213 18 2 2 18
S CAN2 WA11 B1 A1 A1 B1
35 212

9
8
7
6
5
4
3
2
36 209 WA4 19 19

G ND

G ND
LED[0..2] OE OE
37 208 WA12 R A37 1 1
WA3 10k C129 DIR DIR
XSW[0..3] 38 207
39 206 WA13 0.1u D +3. 3 IC23

10

10

10
1
40 205 WA2 LV245A
S CAN[0..2]
204 WA14 IC24
WA1 LV245A

20
41 203 D D D D
WA15 C130

10
LE 42 202

1
43 199 WA0 W A13 11 9 3WA13 0.1u D +3. 3 D

VCC
RS B8 A8
44 198 WA16 WA2 12 8 3WA2 R A38
WA14 B7 A7 3WA14 10k
45 13 7
WA1 B6 A6 3WA1

20
LP[0..7] 197 14 6 D
LP0 XWOE WA15 B5 A5 3WA15

9
8
7
6
5
4
3
2
48 196 15 5
LP1 WA0 B4 A4 3WA0 WD11 3WD11
49 16 4 9 11

VCC
LP2 WD15 WA16 B3 A3 3WA16 WD4 A8 B8 3WD4
50 195 17 3 8 12
LP3 WD0 XWOE B2 A2 3XWOE WD3 A7 B7 3WD3
51 194 18 2 7 13
LP4 WD7 B1 A1 WD12 A6 B6 3WD12
52 193 6 14

9
8
7
6
5
4
3
2
LP5 WD8 WD10 A5 B5 3WD10
53 192 19 5 15

G ND
LP6 WD14 R A39 OE WD5 A4 B4 3WD5
54 189 1 4 16
LP7 WD1 10k DIR WD2 A3 B3 3WD2
55 188 3 17
WD6 WD13 A2 B2 3WD13
187 2 18

10

10
A1 B1

1
56 186 WD9
R 45 185 WD13 19

G ND
10k 137 184 WD2 D D D +5 1
OE
WD5 DIR
57 183
58 182 WD10 R 46 IC25

10
D 59 179 WD12 10k LV245A
178 WD3
D[0..15]
D11 62 177 WD4 D
D4 63 176 WD11
D3 64
D12 65 175 V0E A3
D10 66 174 V0E A2
D5 67 173 V0E A1 D +5
D2 68 172 V0E A0 R A40
D13 69 169 10k
D9 72 168 V0E A9 28 41 V 0E D15 V 0E D4 1 16
D6 V0E A4 V0E A8 A9 DQ15 V 0E D13 V 0E D5
73 167 27 40 2 15
D1 V0E A5 V0E A7 A8 DQ14 V 0E D0 V 0E D6
74 166 26 39 3 14
D14 V0E A6 V0E A6 A7 DQ13 V 0E D2 V 0E D7
75 165 25 38 4 13
D8 V0E A7 V0E A5 A6 DQ12 V 0E D11 V 0E D8
76 164 24 36 5 12
D7 V0E A8 V0E A4 A5 DQ11 V 0E D9 V 0E D9
77 163 23 35 6 11
D0 V0E A9 V0E A3 A4 DQ10 V 0E D7 V 0E D10
78 162 20 34 7 10
D15 V0E A2 A3 DQ9 V 0E D5 V 0E D11
A[1..8] 79 19 33 8 9
V 0E OE V0E A1 A2 DQ8 V 0E D4 V 0E D3
159 18 10 1 16
A1 V0E CAS V0E A0 A1 DQ7 V 0E D6 V 0E D2
82 158 17 9 2 15
A2 V0E RAS R A42 A0 DQ6 V 0E D8 V 0E D1
83 157 8 3 14
A3 84 156 V 0E WE 10k D +5 D +5 32
DQ5
7 V 0E D10 V 0E D0 4 13
A4 V0E A0 NC DQ4 V 0E D3 V 0E D12
85 8 1 16 5 5 12
A5 V 0E D4 V0E A1 NC DQ3 V 0E D1 V 0E D13
86 155 7 2 15 4 6 11
D +5 A6 87 154 V 0E D5 V0E A2 6 3 12
NC DQ2
3 V 0E D12 V 0E D14 7 10
A7 V 0E D6 V0E A3 R 47 R 48 R 49 R 50 NC DQ1 V 0E D14 V 0E D15
88 153 5 4 11 2 8 9
R 40 A8 V 0E D7 10k 10k 10k 10k NC DQ0
89 152
10k 149 V 0E D8 D 21 R A41
V 0E D9 V0E RAS VCC D +5 10k
XINTV0 92 148 14 6 D
V 0E D10 R AS VCC
XWAIT 93 147 30 1
V 0E D11 V0E CAS UCAS VCC
LEVEL_C ONV. XRD 94 146 31
LCAS
95 145 V 0E D3 V 0E WE 13
B lock XWR
96 144 V 0E D2 V 0E OE 29
WE
XCS V0 OE
97 143 V 0E D1 42
XRSTTG VSS
98 142 V 0E D0 37
R 51 VSS 22
0 C134 XLR CK 1 VSS
99 141
NIU 100 R 52 NIU IC26 C 131 C 132 C133 D
101 136 G M71C 18163C J-6 0.1u 0.1u 0.1u
XLR CK 1
V 0V 1S CK 102 or equivalent
D V 0V 1S D0 103 140
V 0V 1S D1 104 139 R103 NIU
V 0V 1S D2 107 138 OUT 2
OUT 2
V 0V 1S D3 108 133 OUT 1
OUT 1
V 0V 1S D4 109 132 B CK
V 0V 1S D5 110 131 R104 NIU
V 1V 0S D5 111 130
V 1V 0S D4 112 129 OUT 3 R 53 NIU
S YNC
V 1V 0S D3 113 128 B CK
V 1V 0S D2 114 127
V 0V 1S CK
V 1V 0S D1 115 126 LRC K2
V 0V 1S D[0..5]
V 1V 0S D0 116 125 R105 NIU
V 1V 0S CK 117 124 256FS
V 1V 0S D[0..5] OUT 3
TONE V 1V 0S CK 118 123
119 122
G ENER ATOR#1
1

R 54 NIU
S ection LRC K2
151
171
191

106
121
135
161
181
201
221

T P3
211
12
22
31
71

47
61
81
91
1

TP4 R 55 NIU
256FS
D D IC19
TC223C660CF-503 AUDIO
B lock
R01455956

NOTE : "NIU" means "Not In Use."

29 30
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 6/7)

fig.mb-sch6
C135
D +5 100u/6.3V

C136
TONE G ENER ATOR #1 BLOC K C137
0.1u

C139 D +3. 3 0.1u

10u/6.3V C138
0.1u
C140
0.1u
C141
0.1u
C142 C143
0.1u 0.1u
C144 C145
0.1u 0.1u
C146 C147
0.1u 0.1u
C148 C149
0.1u 0.1u
C150
D 0.1u
C151
0.1u TONE
G ENER ATOR#0

150
170
190
210

105
120
134
160
180
200
220
240
TONE

14
30
70
90

46
60
80
D
S ection TONE
G ENER ATOR#0
B lock R 39 4 3
G ENER ATOR#0
XWB RE Q
22 5 2 XWB AC K
S ection
384FS 6
7 239 3WD[0..15]
8 238 XWC S0 3WA[0..22]
9 237 WA[0..23]
IC21C IC21B 10 WD[0..15]
7WU04 7WU04 R 41 11 236 XWOE
22 235 3XWOE
6 2 3 5 13 234
233
R 57 15 232
22k 16 231 3XWCS R0
17 230 3XWCS R1
C152 C153 C154 18 229
R 42 R 44 10u/16V 0.1u 2200p 19
1M 1k 20 228
21 227 WA23
X2 4 1 D 226 WA22 NOR MALBEND R EVER SE BE ND
16.9344MHz 23 225 WA21
24 224 WA20 3WA22 36 46 3WD15 3WA22 36 46 3WD15
C127 C128 WA18 3WA21 A22 O15/A-1 3WD14 3WA21 A22 O15/A-1 3WD14
D 25 223 12 44 12 44
18p 15p WA19 3WA20 A21 O14 3WD13 3WA20 A21 O14 3WD13
26 222 13 42 13 42
WA17 3WA19 A20 O13 3WD12 3WA19 A20 O13 3WD12
27 219 11 40 11 40
WA8 3WA18 A19 O12 3WD11 3WA18 A19 O12 3WD11
D D 28 218 14 35 14 35
WA7 3WA17 A18 O11 3WD10 3WA17 A18 O11 3WD10
29 217 15 33 15 33
WA9 3WA16 A17 O10 3WD9 3WA16 A17 O10 3WD9
32 216 2 31 2 31
WA6 3WA15 A16 O9 3WD8 3WA15 A16 O9 3WD8
215 3 29 3 29
WA10 3WA14 A15 O8 3WD7 3WA14 A15 O8 3WD7
33 214 4 45 4 45
WA5 3WA13 A14 O7 3WD6 3WA13 A14 O7 3WD6
34 213 5 43 5 43
WA11 3WA12 A13 O6 3WD5 3WA12 A13 O6 3WD5
35 212 6 41 6 41
WA4 3WA11 A12 O5 3WD4 3WA11 A12 O5 3WD4
36 209 7 39 7 39
WA12 3WA10 A11 O4 3WD3 3WA10 A11 O4 3WD3
37 208 8 34 8 34
WA3 3WA9 A10 O3 3WD2 3WA9 A10 O3 3WD2
38 207 9 32 9 32
39 206 WA13 3WA8 10 A9 O2 30 3WD1 3WA8 10 A9 O2 30 3WD1
WA2 3WA7 A8 O1 3WD0 3WA7 A8 O1 3WD0
40 205 16 28 16 28
WA14 3WA6 A7 O0 3WA6 A7 O0
204 17 17
WA1 3WA5 A6 D +3. 3 3WA5 A6 D +3. 3
41 203 18 18
WA15 3WA4 A5 3WA4 A5
42 202 19 38 19 38
WA0 3WA3 A4 VCC 3WA3 A4 VCC
43 199 20 37 20 37
WA16 3WA2 A3 VCC 3WA2 A3 VCC
44 198 21 21
3WA1 A2 C155 3WA1 A2 C156
45 22 22
D +5 197 3WA0 23
A1 0.1u 3WA0 23
A1 0.1u C 216
A0 A0 10u/16V
48 196 48 48
IC21A 49 24 G ND 47 24 G ND 47
7WU04 WD15 CE G ND CE G ND
50 195 27 26 27 26
8

WD0 OE/OE /DC G ND OE/OE /DC G ND

51 194 1 25 1 25
1 7 C214 IC21D 52 193 WD7 D +3. 3 W OR D/BY TE G ND D +3. 3 W OR D/BY TE G ND
0.1u 7WU04 53 192 WD8 IC28 D IC29 D
54 189 WD14 UPD23C128040ALGY -525-MJH UPD23C128040ALGY -526-MKH
4

D 55 188 WD1 03010612 03010623

187 WD6
D 56 186 WD9
R 58 185 WD13
10k 137 184 WD2
57 183 WD5
58 182 WD10
D 59 179 WD12
178 WD3
D11 62 177 WD4
D4 63 176 WD11
D3 64 D +5
D12 65 175 V1E A3 R A45
D10 66 174 V1E A2 10k
D5 67 173 V1E A1 V1E A9 28 41 V 1E D15 V 1E D4 1 16
D2 V1E A0 V1E A8 A9 DQ15 V 1E D13 V 1E D5
68 172 27 40 2 15
D13 V1E A7 A8 DQ14 V 1E D0 V 1E D6
69 169 26 39 3 14
D9 V1E A6 A7 DQ13 V 1E D2 V 1E D7
72 168 25 38 4 13
D6 V1E A4 V1E A5 A6 DQ12 V 1E D11 V 1E D8
73 167 24 36 5 12
D1 V1E A5 V1E A4 A5 DQ11 V 1E D9 V 1E D9
74 166 23 35 6 11
D14 V1E A6 V1E A3 A4 DQ10 V 1E D7 V 1E D10
75 165 20 34 7 10
D8 V1E A7 V1E A2 A3 DQ9 V 1E D5 V 1E D11
76 164 19 33 8 9
D7 V1E A8 V1E A1 A2 DQ8 V 1E D4 V 1E D3
77 163 18 10 1 16
D0 V1E A9 V1E A0 A1 DQ7 V 1E D6 V 1E D2
D[0..15] 78 162 17 9 2 15
D15 R A47 A0 DQ6 V 1E D8 V 1E D1
79 8 3 14
159 V 1E OE 10k D +5 D +5 32
DQ5
7 V 1E D10 V 1E D0 4 13
A[1..8] NC DQ4
A1 82 158 V1E CAS V1E A0 8 1 16 5 V 1E D3 V 1E D12 5 12
A2 V1E RAS V1E A1 NC DQ3 V 1E D1 V 1E D13
83 157 7 2 15 4 6 11
A3 V 1E WE V1E A2 NC DQ2 V 1E D12 V 1E D14
84 156 6 3 12 3 7 10
A4 V1E A3 R 59 R 60 R 61 R 62 NC DQ1 V 1E D14 V 1E D15
LEVEL_C ONV. D +5
85 5 4 11
NC DQ0
2 8 9
A5 86 155 V 1E D4 10k 10k 10k 10k
B lock A6 87 154 V 1E D5 D 21 R A46
R 56 A7 V 1E D6 V1E RAS VCC D +5 10k
88 153 14 6 D
10k A8 V 1E D7 V1E CAS R AS VCC
89 152 30 1
V 1E D8 UCAS VCC
149 31
V 1E D9 V 1E WE LCAS
XINTV1 92 148 13
V 1E D10 V 1E OE WE
XWAIT 93 147 29
V 1E D11 OE
XRD 94 146 42
V 1E D3 VSS
XWR 95 145 37
V 1E D2 VSS
XCS V1 96 144 22
V 1E D1 VSS
XRST T G 97 143
98 142 V 1E D0 IC30 C157 C158 C 159 D
R 63 G M71C 18163C J-6 0.1u 0.1u 0.1u
0 C160 99 141 or equivalent
NIU 100
101 136
102
D V 1V 0S D0 103 140
V 1V 0S D1 104 139
V 1V 0S D2 107 138
V 1V 0S D3 108 133
V 1V 0S D4 109 132
V 1V 0S D5 110 131
V 0V 1S D5 111 130
S YNC V 0V 1S D4 112 129
TONE V 0V 1S D3 113 128
V 0V 1S D2 114 127
G ENER ATOR#0 V 1V 0S CK
V 0V 1S D1 115 126
V 1V 0S D[0..5]
S ection V 0V 1S D0 116 125
V 0V 1S D[0..5] 117 124
V 0V 1S CK 118 123
119 122
1

151
171
191

106
121
135
161
181
201
221
211
12
22
31
71

47
61
81
91
1

T P5
1

TP6 IC27
TC223C660CF-503
D D R01455956

NOTE : "NIU" means "Not In Use."

31 32
 May.2002 SD-80

CIRCUIT DIAGRAM (MAIN BOARD 7/7)

fig.mb-sch7

33 34
 May.2002

CIRCUIT BOARD (JACK SHEET)

fig.mb-sch7

35
 SD-80

fig.mb-sch7

36
 May.2002 SD-80

CIRCUIT DIAGRAM (JACK SHEET 1/2)

fig.jk-sch1CIRCUIT BOARD (MAIN)
C1 DOU T
0.1u D +5
JACK1 BOAR D J K8
AS S Y72120490 R 38 IC1A IC1B C 17 R 13 R 14 L15 YK B21-5012

2
47 HCU04 HCU04 47u/25V 470 470 600 OUTPUT1R
1 2 3 4 1 I V C N2 2
G G P1FA501TZ 4
R 15 C 18 1
C 40 100k 100p

3
100p C2 D C N4

3
DOU T 10u/16V S 4B -P H-K-S A
D +5 MIDI D IC1D T1 R1 L1 4 1 Q3 F
D + 3. 3 HCU04 7KQ5 75 600 4
3 R N1442
MIDI 3
9 8 1 6 2 2
D +5 C4 J K2A 2 J K9

2
2 1
10u/16V C3 Y K C21-3117 1 C 19 R 16 R 17 L16 YK B21-5012
3 4 1 A
IC1E 0.1u FG from 47u/25V 470 470 600 OUTPUT1L
HCU04 C5 L2 2

10
20
11 10 NIU C6 C8 C9 600 C 10 C 11 VOL UME 4

3
NIU NIU 0.1u 100p 0.1u B oard R 18 1
C7 100k 1 Q4
C N3 10u/16V IC1F R N1442 L17
18FMN-BT K HCU04 D D D A A C 20 C 21 27
100p 0.1u

2
D 13 12
MIDI C 12 MIDI

30
40
50
18 A
18
17 D +5 0.1u D +5 JAC K2 BOAR D A
17
16
16 AS S Y72120501
15 R2 R3 L3 10 F
15

6
14 DOUT IC4B IC4A 1k 100 600 1
14

1
13 LV04A LV04A 1 4 J K3

4
13 3RXD1 2DJ -0060003
12 4 3 2 1 5 2

2
12 3TXD1 J K10
11 3 5 MIDI IN 1

5
11

3
10 3RXD2 3 R 19 R 20 L18 YK B21-5012
10

3
9 3TXD2 R4 L4 470 470 600 OUTPUT2R
9 120 600

4
8 2 1 2
8 IC2
7 D 6 4
7 USB N P C410L DA6 6 R 21 C 23
6 5 1
6 MA142WK 5 10k 100p

30
40
50
5 4
5 USB P 4
4 3

3
4 MIDI 3
3 2 A D
3 V BUS D +5 R5 L5 2 Q5
2 10 1 1
2 220 600 1 R N1442
1 1
1

1
4 J K4 C N5 J K11

4
2DJ -0060003 S 6B -P H-K-S R 22 R 23 L19 YK B21-5012

2
D D 2

2
USB 470 470 600
from 5 MIDI OUT1 from A OUTPUT2L

5
3

3
3 2
MAIN 5 6 1 Q1 R6 L6 MAIN 4

3
B oard R N1414 220 600 B oard R 24 1
IC4C 10k 1 Q6
LV04A R N1442 L20
2
D A
A C 25 C 26 27
100p 0.1u

2
D
A
MIDI C 13 MIDI

30
40
50
D +5 0.1u D +5
A D
R7 R8 L7 10
6

IC4D IC4E 1k 100 600 1

1
LV04A LV04A 1 4 J K5

4
8 9 10 11 5 2 2DJ -0060003

2
3 5 MIDI IN 2

5
3
D F 3
3

R9 L8 S W1A S W1B
120 600
4

2 1 S DK LA1-B S DK LA1-B
D IC3 1 2
P C410L DA7 10 20

30
40
50
MA142WK

3
MIDI
D +5 R 10 L9 10

3
220 600 1 1
R A1 4 J K6 C N12
4

100 2 2DJ -0060003

POWER AS SY
2

1 8 5 MIDI OUT2
5
3

2 7 3 02906090WIR IN G AS S Y72125767
3 6 3 2 13 12 1 Q2 R 11 L10
4 5 1 R N1414 220 600 2X50-P 4-3P SDN-3P SDN-F
IC4F C N1
S W2A LV04A C N11 B OARD1 D1 C 22 B12B-PH-K -S
2

D
SSSF 112-S06N1 A1DU2L3B104-V ER -3 DSK10C 47u/25V 12
12

3
D L11 1 8 1 2 11
27 E AR TH +15V 11
10
C 24 10

3
7 2 1 9
J K7 -15V 47u/25V 9
4 3 8
L24 D2 8
5 2 6 7
ZCY S51R5-M3PAT AGND DSK10C 7
6 1 3 2 6
NIU LIVE 6
2 5 5
DGND 5
1 2 4
L12 4
D 4 1 3 4 3
USB 27 NEUTR AL +5V 3
2
J K1 C 39 2
10 1
FANTOM W IR IN G W 3 1000u/6.3V 1
20
C 14 R 12 L13
DOU T 0.1u 1k 600 Y K F45-0020
D +5 D +3. 3
to
D
MAIN B oard
14
14

IC1C L14 F A D
HCU04 IC4G C 16 S W2B 27
C 38 C 15 5 6 LV04A 0.1u SSSF 112-S06N1
10u/16V 0.1u
J K2B
7

D
Y KC 21-3117 USB
7

D 10 20
IC1G
D HCU04
10

D D

"NIU" means "Not In Use."

37 38
 May.2002 SD-80

CIRCUIT DIAGRAM (JACK SHEET 2/2)

fig.jk-sch2

to J AC K1 V OLUME B OARD E NC ODER BOAR D

B oard AS S Y72120534 AS S Y72120545
4 C N10
4 OUT 1R S 4B -P H-K-S
3
3
2 from 1 1

A
2 OUT 1L 1 E N1A
1 2 2

EN
1 MAIN 2 E C12E2420801
3 3
3

B
C N6 R 25 Board 4
S 4B -P H-K-S 22 L21 4
6 - 1/2W 600
7
5 + 10

A
C N7 E N1B

EN
3
S 8B -P H-K-S + R 26 IC6B R 36 C 27 E C12E2420801 20

B
8 R 27 220 1 Q7 NJM4565MD 4.7k 100p
8 10k R N1442
7
7 S ENDR
6 A F F
6 R 28

2
5 A
5 S ENDL 22 L22
4 A
4 1/2W 600
13

23

3 2 - 2
3
2 1 3
2 MUT E
1 12 22 3 + 1
1
- R 29 IC6A R 37 C 30 J K12
21
11

3
from R 30 220 NJM4565MD 4.7k 100p YK B21-5009
10k 1 Q8 L23
MAIN R N1442 A F 27
B oard A A A
V R1A V R1B

2
10kB 10kB A C 31
R K09L12B0A22 0.1u
02904145 +
A F

8
V R1C C 33
0.1u -
20 10 IC6C
+ NJM4565MD
C 35
A 0.1u

4
F

PAN EL BOAR D LCD BOAR D

AS S Y72120512 S W3B S W12B LED1 AS S Y72120523
S KHQF M S KHQF M S LR -56VC T32
6 5 6 5 1 2
1 2
INS T/DR UM P RE VIEW G M2 D +5 R 31 LED6
120 C L-191B1
S W4B LED5 LED2
S KHQF M S LR -56DC T32 S LR -56VC T32
6 5 1 2 1 2 IC7
C N9 R CM2072M-B 1 2
E FF EC TS USB NAT IVE 16FMN-BT K 1
RS R 32 LED7
16 2
16 R /W 120 C L-191B1
15 3

2
S W5B LED4 LED3 15 E
14
C N8 S KHQF M S LR -56MC T32 S LR -56VC T32 14 LP0 LP7 D5
13 11
14FMN-ST K 13 LP1 LP6 DB7 6.8V
6 5 1 2 1 2 12 10 1 2
LSC AN2 12 LP2 LP5 DB6
14 11 9
14 LSC AN1 11 LP3 LP4 DB5 R 33 LED8
S YS TE M MIDI GS

1
13 10 8
13 LSC AN0 10 LP4 LP3 DB4 120 C L-191B1
12 9 7
12 LED2 9 LP5 LP2 DB3
11 8 6
11 LED1 8 LP6 LP1 DB2
10 7 5
10 LED0 7 LP7 LP0 DB1
9 6 4 1 2
9 6 DB0
8 5
8 S S CAN2 5 R 34 LED9
7 4 13
7 S S CAN1 4 V DD 120 C L-191B1
6 3 14
6 S S CAN0 S W5A S W10 S W7 S W12A 3 VIN
5 2
3

5 XSW3 S KHQF M S KR GAED010 S KR GAED010 S KHQF M 2

4 1 15
4 XSW2 1 V5
3 2 4 2 1 1 2 1 2 2 1 2 4 1 2
3 XSW1
2 1 3 1 3 12
2 XSW0 DA1 DA2 V SS R 35 LED10
1
1 S YS TE M S HIFT PAR T > P RE VIEW from 16
G ND
MA142WK MA142WK 120 C L-191B1
MAIN C 36 C 37
from B oard 0.1u 0.1u
F
MAIN S W4A S W9 S W6 S W11
3

B oard S KHQF M S KR GAED010 S KR GAED010 S KR GAED010

2 4 2 1 1 2 1 2 2 1 1 2 F
1 3
E FFEC TS DA3 C UR SO R> PAR T < DA4 E NTER
MA142WK MA142WK

S W3A S W8
3

S KHQF M S KR GAED010
2 4 2 1 1 2
1 3
INS T/DR UM DA5 C UR SO R<
MA142WK

"NIU" means "Not In Use."

39 40
 May.2002

ERROR MESSAGES
When data are not processed properly or when other problems occur, an error
message appears. When an error message appears, take the following actions.

MIDI Error
Cause 1: Power of the MIDI device connected to the MIDI IN connector may
have failed.
Action 1: The SD-80 is not the problem. Confirm the power of the MIDI device
connected.
Cause 2: The MIDI cable may be pulled off, or broken.
Action 2: Check the MIDI cable.

MIDI Error !!
Cause: MIDI communication is not done properly. An overrun, framing or
parity error may have occurred.
Action: Check if the MIDI transfer rate of the MIDI device connected to the SD-
80 is proper. If this error message appears even after the above action, there
may be a problem with the SD-80’s CPU. Check the CPU circuit and related
circuits of the SD-80.

MIDI Buffer full

Cause: Since a large amount of MIDI data was received in a short time,
processing could not be done.
Action: Check if a large amount of MIDI data was sent in a short time.

USB Off Line

Cause 1: Power of the computer connected to the USB connector may have
failed.
Action 1: The SD-80 is not the problem. Confirm the power of the computer
connected.
Cause 2: The USB cable may be pulled off, or broken.
Action 2: Check the USB cable.

Check Sum Error

Cause: Checksums of the exclusive messages received disagreed
Action: Check the contents of the data sent to the SD-80, and send them again.
Make sure that the MIDI cable is not broken.

SysEx Data error

Cause: The exclusive messages received contain errors.
Action: Check the contents of the data sent to the SD-80, and send them again.

41