WELCOME!

Thank you and congratulations

for purchasing the Vectrix Maxi Scooter! You are helping the environment and your daily commute as well! We hope that you enjoy the experience! If you need any
repairs to your Vectrix or just want some friendly advice, please see your local dealer service center. This manual is provided to help you get to know your Vectrix.

Enjoy Your Vectrix

Maxi Scooter

VECTRIX ZEV OWNER’S MANUAL 

 TABLE OF CONTENTS
General 3 Maintenance 30
Warranty 3 Battery Pack 31
Symbols Contained in This Manual 3 Checking Brake Fluid Levels 32
Safe Riding 4 Checking Brake Pads for Wear 33
Maximum Weight Allowance 5 Bulb Replacement 34
Vehicle Identification Number (Vin) 6 Beam Setting 35
Fuses 36
Tires 37
CONTROLS 7 Cleaning 39
Instrument Cluster 8 Storing 40
Key Lock/ignition 12 Transporting 41
Left Handlebar Switches 13 Troubleshooting 42
RIGHT Handlebar Switches/THROTTLE 14

Technical Data 44
Main Components 16 Specifications 44
Side and Center Stand 17 Range 45
Storage Compartments 18 Performance Data 47
Rear Shock Absorbers 19
Rear Wheel Drive 20
Battery Pack 21 USA Information 48
Motor Controller 23 Safety Defects 48
Label Locations 49

Use 24
Pre-Ride Checks 25 SWITZERLAND INFORMATION 48
Interlocks 25 Power cut off information 48
Braking 26
Parking the Vehicle 28
Charging the Battery 29 Routine Maintenance Record 51

 VECTRIX ZEV OWNER’S MANUAL

 GENERAL
WarRANTY SYMBOLS CONTAINED IN THIS MANUAL:

Your Vectrix is warranted for twenty-four months.

To maintain the warranty you must comply with WARNING!
the servicing requirements called out in the Vectrix
Warranty Book. When this symbol is shown, it means that you
must read this section. Failure to read this section
could result in injury or death!

NOTE!
When this symbol is shown, it means that there is
some important information that will help you enjoy
your Vectrix even more!

VECTRIX ZEV OWNER’S MANUAL 

 SAFE RIDING
In order to operate your Vectrix properly, you must parking to prevent it from tipping over. It is SAFE RIDING
familiarize yourself with the bike’s controls and recommended that you put down the side stand These safety tips are useful and may save your life
movements. before you dismount your Vectrix to park. in case of a potential accident. Please read and
understand these tips before riding your Vectrix.
n ALWAYS ride with your license and insurance n ALWAYS avoid parking on sand, gravel or soft Defensive driving is more important on a Vectrix
certificate in your possession. surfaces. versus in a car. Always wear protective gear, but
understand that protective gear cannot totally protect
n ALWAYS wear a safety helmet. n Become familiar with the handling of the Vectrix you in the event of an accident.
before carrying a passenger. You should instruct
n ALWAYS hold both ends of the handlebar/ your passenger about safety on a Vectrix. Always use turn signals to alert other drivers of
handgrips. A passenger should have his hands on the your intentions. Use caution in bad weather when
passenger grab rail or wrapped around the driver roads become wet and slippery. Sudden braking can
n ALWAYS remain seated while riding the Vectrix. of the Vectrix at all times that the Vectrix is in cause the Vectrix to become unstable and cause an
Do not stand while riding. motion. accident.

n ALWAYS obey state- and local traffic laws. n Never permit an inexperienced rider to ride on or DO NOT DRINK ALCOHOL OR TAKE MIND-ALTERING
DRUGS AND RIDE
drive your Vectrix. You are responsible for telling
n In the event of bad weather, adjust your speed to them about Vectrix safety and safe handling.
PROTECTIVE APPAREL
reflect the type of weather while obeying speed When riding, Vectrix suggests that you always wear
limits. n ALWAYS use your turn signals to identify your a safety helmet. Studies have shown that there is
intent to change lanes or turn. a direct correlation between head injury and a lack
n Wear appropriate clothing to ride. A helmet, of helmet use (NHTSA Traffic Safety Facts, October,
proper eye protection, boots and gloves are a 2007). It is recommended that you wear above-
must. ankle boots and that you wear eye goggles when not
SAFETY RULES AND REGULATIONS
Traffic rules and regulations vary from jurisdiction wearing a full helmet. Without eye protection wind
n Park in an area that is visible to others, and and debris could get into your eyes and cause an
to jurisdiction. Please become aware of those rules
always have either your center or side stand accident.
and regulations that apply to you before riding your
down when parked. Do not leave the key in your
Vectrix.
ignition unattended. This vehicle is not intended for off-road use.

n ALWAYS maintain control of your Vectrix when

 VECTRIX ZEV OWNER’S MANUAL
 MAXIMUM WEIGHT ALLOWANCE
The maximum gross vehicle weight is 938 lbs.
(425 kg), which includes the Vectrix, rider, passenger
and cargo.

Make sure any luggage put on the Vectrix is firmly

placed and secured. Do not overload your Vectrix or
arrange heavy items higher up on the Vectrix. Do not
attach items to the handlebars. Do not wear long or
loose clothing while riding, as the pieces could get
caught in components of the Vectrix. Do not jam any
items in any openings on the Vectrix, as this could
cause loss of stability and failure of the Vectrix.

Vectrix Underseat Trunk Capacity 26 lbs. (12 kg)

Vectrix Glove Box Capacity 4 lbs. (2 kg)
Cargo Box and Contents not to exceed 20 lbs (9 kg)

VECTRIX ZEV OWNER’S MANUAL 

 VEHICLE IDENTIFICATION NUMBER (VIN)
The VIN is located on the back of the frame in the
right bottom corner. It is stamped into the metal.

The Manufacturer’s Data Plate is located adjacent

to the VIN stamping on the bottom right rear
frame. This label displays the VIN (upper section),
Manufacturer’s name, type approval mark, the VIN
printed again (lower section) and the Static Sound
Level.

The VIN is a 17-digit alphanumeric code which

uniquely identifies your bike. The VIN meets NHTSA
(US) and ISO (EU) requirements. The VIN number
should be used when ordering parts so that Vectrix
can access its database to ensure that the correct
and appropriate parts are provided.

The DOT certification label is located on the front of

the bike behind the front wheel well. (USA only)

VIN #: 0XXXX00000X000000

EXAMPLE:

VECTRIX SP Z.O.O.
DOT
e00*0000*00*0000*
Certification
OXXXX00000X000000
Label
* dB (A) – * 1/min

 VECTRIX ZEV OWNER’S MANUAL

 CONTROLS

WARNING!
In order to properly run your vehicle, you must
read and understand this section of the manual. It
will help you get more familiar with your Vectrix.
Instrument Cluster

Left Handlebar

Regen Throttle

Ignition Switch

VECTRIX ZEV OWNER’S MANUAL 

 INSTRUMENT CLUSTER Fig 1.0

15 16 17 18 19 20 21 22 23 24

Telltales

25

11 14
10

13 26
7

5 8 9
6
4
12
1
2 3
Left Status LCD Fuel Level LCD
27

Speedometer / Odometer

 VECTRIX ZEV OWNER’S MANUAL

 INSTRUMENT CLUSTER
Fig 1.0 illustrates where items 6. RF RANGE INDICATOR 12.ODOMETER READING
1–30 are located RF signal strength for future enhancements. The odometer reading lets you see how many
total miles or kilometers you have traveled on
1. TRIP A-B OR ODOMETER INDICATOR 7. READY INDICATOR your Vectrix. During charging this will indicate the
Indicates mileage reading is currently displayed. This is displayed when the system is ready to be charge mode and the charge termination voltage.
Use the select button (labeled ‘S’) to select enabled. Modes are “CP” for constant power, “tr” for
between Trip A, Trip B or the odometer. transition or cool down, “EC” for end of charge,
8. GO INDICATOR and “CC” for constant current.
2. TRIP ODOMETER INDICATOR The GO Indicator will light up when the system is
Can be displayed in either miles or kilometers by enabled to accelerate. 13.KM/H INDICATOR
selecting the button marked ‘K/M’. Displays your speed in kilometers per hour.

3. ODOMETER OR TRIP A-B READING 9. BATTERY CHARGE/CHARGING INDICATOR 14.MPH INDICATOR

Displays the mileage of the currently selected trip When the system is being charged by an external Displays your speed in miles per hour.
or odometer. Use the button label “E/M” to switch power source, the Battery Charging Indicator will
between km and MILES. If the wrench icon is illuminate. 15. LEFT DIR. INDICATOR LAMP TELLTALE
illuminated this will display an abbreviated fault Flashes green when the left turn directional
code. During charging this will display the highest 10.CLOCK READING is on and functioning properly. Illuminates a
battery module temperature in C°. Displays the time of day in either 12 or 24 hour steady green if one of the directionals is not
format. This will display the total charge time functioning.
4. ESTIMATED RANGE READING while charging or the remaining cool down time
Displays the estimated range available (km or during the transition mode. 16. PARKING/POSITION LAMPS TELLTALE
miles) based on your recent driving profile. Hard Illuminates green when the position lamps are in
accelerations and high speeds will decrease this 11.SPEEDOMETER (KM/H – mph) use and working properly. If either is not working
value. Soft accelerations and slower speeds will The speedometer displays your current speed the icon will flash.
increase this value. During charging this will in both km/H and mph.During charging this
display the battery voltage. indicates the charge current times 10. For
example, if dial indicates 110, charge current is
5. BLUETOOTH INDICATOR 11 amps.
This indicator is installed for future
enhancements.

VECTRIX ZEV OWNER’S MANUAL 

 INSTRUMENT CLUSTER
17. HIGH TEMP TELLTALE 20. MAIN-BEAM HEADLAMP TELLTALE
This will illuminate in red when the battery or 23. REVERSE TELLTALE
When the main beam is selected and operational,
key system components exceed safe operating Indicates that the Vectrix is in reverse mode.
this icon will illuminate as a steady blue light. If
temperature. If the telltale is flashing, see trouble non-operational, this icon will flash.
shooting guide. 24. RIGHT DIR. INDICATOR LAMP TELLTALE
Flashes green when the right turn directional
21. BATTERY TELLTALE
Warning! is on and functioning properly. Illuminates a
This icon will illuminate when the battery voltage
steady green if one of the directionals is not
is low, indicating that performance and range
The Vectrix will continue to operate, but at a functioning.
reduced performance level. Continued operation are limited. If the telltale is flashing, see trouble
could result in permanent damage. shooting guide. 25. BATTERY LEVEL INDICATOR
Allow to cool. The battery level indicator is a 17-bar graphic
Warning! chart that shows how much charge is left in the
If, after you have cooled and charged your Vectrix, battery.
18. SIDE/CENTER STAND TELLTALE the battery telltale continues to illuminate, contact
An amber light will illuminate if the side stand is an authorized dealer.Call authorized Dealer. 26. BATTERY INDICATOR
down or lowered. Indicates the Vectrix is running on battery.
22. MAINTENANCE REQUIRED TELLTALE 27. LIGHT SENSOR
When this amber colored light is illuminated, The light sensor detects the level of ambient light
Warning! take your Vectrix to an authorized dealer to be and adjusts the LCD backlighting.
checked.
The Vectrix will not operate when the side is in the
down or lowered position. There is an interlock Warning!
which prevents the Vectrix from being enabled
unless the side stand is in the up position. You must get your Vectrix checked if this light is
illuminated. See note on Trip Odometer about fault
19. DIPPED-BEAM HEADLAMP TELLTALE codes.
When the low beam is selected and operational,
this icon will illuminate as a steady green light. If
non-operational, this icon will flash.

10 VECTRIX ZEV OWNER’S MANUAL

 INSTRUMENT CLUSTER
A1. km/H – mph Selector Setting Your Clock:
This allows you to switch between kilometers and Simply push the hour or minute Note!
miles. The pushbutton is labeled “K/M”. Simply push button to the desired time.
the button to switch to the desired measurement. You can switch from 12 hour to 24 hour modes by
Your desired measurement will be illuminated on the holding the hour button for three (3) seconds.
left LCD screen.

Note!
The default setting is kilometers. A1 km/H-MPH
A3 Minute
Adjustment Selector
A2. Trip A-B Odometer Selector
A4 Hour A2 Trip A-B
Labeled as an “S” on the switch assembly, it allows
Adjustment ODO Selector
you to scroll through Trip A, Trip B and the normal
odometer settings.

Scrolling and Resetting Trips:

By pushing the A2 button you can scroll between
the odometer, Trip A and Trip B. To reset Trip A or
B, scroll to the desired trip and press the button for
three (3) seconds.

A3. Minute Adjustment

This allows you to change the minutes on your
clock. The push button is marked with an “M” to
signify minutes.

A4. Hour Adjustment

This allows you to change the hour on your clock.
The push button in marked with an “H” to signify
hours.

VECTRIX ZEV OWNER’S MANUAL 11

 Key LOCK / IGNITION
Only one key is needed to start your Vectrix, get into 4. GLOVE BOX To do this push the key down and turn it clockwise
the storage area, open your glove compartment and In this position you will be able to pop open the to the trunk position.
lock your bike. glove box. To do this, push the key down and turn
it counter-clockwise to the glove box position. To
The ignition switch is located in the center of the lock the glove box, simply shut the door and it will Note!
Vectrix in front of the stepthrough. The ignition automatically lock itself.
features a number of positions that allow you to lock Do not attempt to open your trunk while someone
and unlock areas of the Vectrix. 5. TRUNK UNLOCK is sitting on the trunk. This could cause the
In this position you will be able to open the trunk. mechanism to break.

Note!
1. Lock Steering 2. System Off
Duplicate Keys
See your service center for duplicate keys.

Positions:

1. LOCK STEERING
When the key is turned to this setting, you are
able to lock the steering mechanism. You simply
pull out the key and your Vectrix is fully locked
until reinsertion of the key. 3. System On 4. Glove Box 5. Trunk Unlock

2. SYSTEM OFF
In this position the Vectrix will be off, including the
motor and lights.

3. SYSTEM ON
In this position you will be able to ride the
Vectrix.

12 VECTRIX ZEV OWNER’S MANUAL

 Left Handlebar Switches
1. MAIN/DIPPED BEAM SWITCH Main-Beam Pass
This switch allows the user to switch from high 4. HORN SWITCH Switch
to low beam. Push up to select low beam to high By tapping the horn you will hear a chirping noise
beam or push down to select high beam to low to alert people you are coming. Or, if you hold Main/Dipped Beam
beam. onto the horn switch, it will first chirp and then Switch
make a louder sound.
2. MAIN-BEAM PASS SWITCH
This switch is used to let other drivers know that 2
you are passing. Pulse the switch to flash your
main beam. The switch is located on the back
side of the handlebar.

3. LEFT/RIGHT DIRECTION SWITCH 1

To engage the turn signal, move the switch to
the right to signal a right hand turn and move the
switch to the left to signal a left hand turn. Push
the button back to reset the switch. If a directional
is left on for more than 20 seconds and the bike
is moving, the horn will chirp to alert the rider that
4 3
the directional is still active.

Note!
Left/Right
Always use turn signals to make other motorists Direction Switch
aware of your intentions.

Horn Switch

VECTRIX ZEV OWNER’S MANUAL 13

 RIGHT Handlebar Switches/THROTTLE
1. Throttle/Regen Position Regenerative Braking / On/Off Cut-off
The throttle on the right handlebar is a distinctive Reverse Switch
feature of your Vectrix. The throttle is the user
interface which determines forward motion as
well as implementing regenerative (regen) braking 2
and the reverse feature. The bi-directional throttle
is very simple to use.

n Roll the throttle downward (rearward) to B

accelerate in the forward direction. (A)

n Release the throttle and it returns to a neutral

position.

n To activate regenerative braking simply roll the

throttle forward beyond the neutral position and
you will progressively engage in regenerative
braking. (B) Always ‘cover’ the front brake lever Acceleration
with the index and middle fingers of your right
A
hand when using regenerative braking to slow
the vehicle. This will ensure that you are ready
to apply the front brake if it becomes necessary
to slow the vehicle more quickly. Never use the
rear brake lever (on the left handlebar) by itself
or with regenerative braking without also using
levers (which actuate the front and rear disc
the front brake lever (on the right handlebar).
brakes) at all times while riding, including while
Using only the rear brake may result in the rear
using regenerative braking. See “Braking” on
tire sliding, particularly when regen is used.
Page 26.
Be ready to pull both the front and rear brake

14 VECTRIX ZEV OWNER’S MANUAL

 RIGHT Handlebar Switches/THROTTLE
n Your Vectrix has the ability to reverse at very low
speeds to assist you with maneuvers such as
backing out of parking spots. Reverse is only
enabled when the Vectrix is completely stopped.
The Vectrix will reverse at a slow speed of
2 mph (3 km/h). Release the throttle and the
reverse drive ceases. To activate reverse from a
complete stop, return the throttle to the neutral
position or a slightly positive position (in the A
direction). Now roll the throttle forward (in the B
direction) to move in reverse. By requiring that
the throttle returns to neutral before activating
reverse, the bike is prevented from going into
reverse immediately after using regen to stop.

2. ON/OFF CUT-OFF SWITCH

The power switch is a fast, convenient method of
shutting down the Vectrix in either an emergency
or under normal operation. Use your right thumb
to operate the power switch. Push down to turn
the switch on and push up to turn the switch off.

VECTRIX ZEV OWNER’S MANUAL 15

 MAIN COMPONENTS

Instrument Cluster
(Pg 8) Rear Shock Absorber (Pg 19)
Rear View Mirrors
Left Handlebar Switches Trunk
(Pg 13) (Pg 18)
Right Handlebar Switches/
Throttle (Pg 14) Charging Cord
(Pg 29)
Headlight Keylock / Ignition Switch
(Pg 34) (Pg 12)
Glove Box Battery
(Pg 18*) (Pg 21)

Side Stand
(Pg 17) Rear Wheel Drive
Center Stand (Pg 20)
(OPTIONAL)
16 VECTRIX ZEV OWNER’S MANUAL
(Pg 17)
 Side and Center stands
Side Stand Center Stand (optional) Never park your Vectrix on soft earth. You should make
The side stand is located on the left side of the The center stand is an optional feature of the Vectrix. every attempt to park your Vectrix on a level, hard
Vectrix. To lower the stand, push down on the side To lower the center stand, push down on the thrust surface.
stand bar, which protrudes out from the side stand. arm with your foot while slowly pushing the bike in
the rearward direction. The Vectrix should “snap” Always park in an area where you are visible to other
Park on level hard surfaces. Avoid parking on hills or onto the stand. To disengage the center stand, rock motorists, so as to avoid possible damage to your
unstable ground. the Vectrix forward and make sure the center stand Vectrix.
is properly retracted.
To put the stand back up, move the Vectrix to a
vertical position and lift the side stand bar with your
foot. NOTE!

Warning! There is a telltale on the middle of the instrument

panel that will illuminate when the side stand is
The side and center stands must be in the upright down.
position in order to safely operate the Vectrix. Failure
Warning! to move the stand up could result in injury to both you
and the Vectrix. There is an interlock which prevents
Do not sit on the Vectrix while the stand is down.
the Vectrix from being enabled unless the side stand
is in the up position.

Note!
Always check the ground before putting the side
or center stand down to ensure that the ground is Thrust Arm
stable. Hot temperatures can cause the stand to
sink into the pavement, so it is recommended to
have a small metal plate for the stand to rest on
in high heat.

VECTRIX ZEV OWNER’S MANUAL 17

 Storage Compartments
UNDER-SEAT HELMET STORAGE/TRUNK To close your glove box, simply shut the compartment.
The Vectrix has a hidden storage area for your helmet The door locks itself with a click.
located under the passenger seat. Your key controls
the lock to the under-seat storage compartment. The glove box contains a panel-mounted 12 VDC,
0.5 AMP mobile phone power point for charging
OPENING TRUNK your mobile phone.
Push down on key and turn clockwise to the “Trunk”
position while off of the seat to open the trunk area.
The passenger seat will lift up. Pull the seat upward
to get it off of the latch. Inside you will see the
charging cord and a place to store your helmet.

CLOSING THE TRUNK

After checking to ensure everything is secured
properly and not overflowing, hold the passenger NOTICE
seat and bend the spring to lower the seat. The seat
will automatically lock itself. ACCESSORY PORT
12 VDC 0.5 AMPS (6 WATTS)
TRUNK COMPONENTS
MAXIMUM
The trunk storage area includes the charging cord for
the Vectrix. The 8 ft (2.4m) charging cord is coiled
in the trunk.
Trunk Position Glove Position
GLOVE BOX COMPARTMENT
Your key will open your glove box. Push down on
the key and turn it counter-clockwise to the glove
box position.

18 VECTRIX ZEV OWNER’S MANUAL

 Rear Shock Absorbers
Your Vectrix is equipped with dual rear adjustable
shock absorbers to enhance your riding experience.
You should periodically inspect the exterior of
the shocks for signs of fluid leakage. If a leak is
indicated, see an authorized dealer at your earliest Shock Absorbers
convenience.

VECTRIX ZEV OWNER’S MANUAL 19

 Rear Wheel Drive
PLANETARY GEARBOX
The single stage planetary gearbox is permanently
sealed and lubricated with no maintenance required.
To vent the gearbox, there is a small vent cap located Vent Cap
on the top side of the motor side swing arm centered
on the motor. This vent should be kept clean of dirt,
debris and excessive water. Motor / Gearbox

BRUSHLESS DC MOTOR
The brushless DC motor is mounted in the motor side
swing arm with its shaft connected to the gearbox in
the rear wheel. There is no need for the consumer
to remove the motor cover. Motor cover removal
should only be done by an authorized service agent.
Removing the motor cover could lead to entrance of
dirt and moisture and/or disrupt the adjustment of
the encoder.

Motor Side Swing Arm

20 VECTRIX ZEV OWNER’S MANUAL

 Battery Pack
DESCRIPTION OF BATTERY PACK
The proper care of your battery pack is essential for
maximum Vectrix performance. The battery has a
nominal bus voltage of 125 volts DC which, if not
respected, could result in serious injury. Only an
authorized service agent is qualified to have access
to the battery pack.

Your battery pack consists of two boxes located

within the Vectrix frame. Each battery box weighs
approximately 99 lbs. (45 kg). Only an authorized
service agent is qualified to troubleshoot a battery
related issue.

Warning!
Opening battery packs is dangerous. Doing so will
void your warranty. DO NOT OPEN.

The battery pack needs to be kept within distinct

operating temperature. The battery includes two
fans, built into an air plenum, which draw cooling air
through the battery boxes. The fans run in response
to temperature and are active while the Vectrix is
running and while charging the battery. You will detect
the sound of the fans when they are operating.

The battery pack is connected to the motor controller

VECTRIX ZEV OWNER’S MANUAL 21

 Battery Pack
through a 125 amp fuse. This fuse is only accessible
to qualified service technicians.

Your battery likes to be charged. You should plug it in

whenever it is convenience to do so. This is referred
to as opportunity charging.

Occasionally the estimated range and fuel gauge may

drop from a few miles/kilometers and a few bars to
zero. This means your charger memory and battery
level need to be synchronized – see troubleshooting
guide.

If this ‘drop off’ continues to occur on a regular basis

it may indicate a problem with the battery contact an
authorized dealer.

22 VECTRIX ZEV OWNER’S MANUAL

 Motor Controller
The motor controller is the “brain” of the Vectrix and
provides the interface between the battery pack and
the motor. The design uses a single circuit board for
power system interconnections as well as control
components and onboard power supplies. The motor
controller incorporates Digital Signal Processing
(DSP) technology as part of the proprietary Electronic
Control System (ECS), which provides the flexibility
to incorporate additional features as required.

WARNING!
Only a Vectrix authorized dealer should
troubleshoot or repair a motor controller. Removal
of the cover and/or alteration of the motor
controller in any fashion voids the warranty and is
extremely hazardous.

VECTRIX ZEV OWNER’S MANUAL 23

 Use
With any new vehicle you must first get used to the
feel of the vehicle before driving in any dangerous
conditions. Bad weather can cause even an experienced
driver to get into an accident. You should use caution at
all times while riding your Vectrix.

Warning!
This Vectrix is designed for and limited to a top
speed of 62 mph (100 km/h). You should avoid
braking suddenly. Quick braking can cause you to
become unstable and lose control of your Vectrix,
especially on loose pavement and/or wet road
surfaces.

BATTERY CONDITIONING
For maximum performance from the battery pack,
the Vectrix needs to experience five (5) initial
charge/deep discharge cycles. These cycles allow
the battery to become fully conditioned and able to
perform as designed.

Note!
Prior to the initial five (5) charge/deep discharge
cycles, you may experience a lower Vectrix range.
With each initial deep discharge/charge cycle, the
range will improve.

24 VECTRIX ZEV OWNER’S MANUAL

 Pre-Ride Checks
TIRES BRAKE LEVER ENABLE SEQUENCE
Warning! Always check both tires for punctures, tears, or worn Once the “Ready” icon is steady ON, you can begin
tread. Never ride on balding or bald tires. Maintain the motor enable sequence. First, apply and hold
For safety reasons it is extremely important that tire pressure at 33 psi (2.2 bar) for the front tire and the left brake, then apply the right brake. “GO” will
you read and understand this section. Failure to 40 psi (2.8 bar) for the rear tire. appear on the left LCD. The Vectrix is now ready to
perform these pre-ride checks could result in drive.
serious injury or death. BRAKE FLUID LEVELS
Refer to the section on brake fluid level. Make sure CABLES AND HARNESSES
that you have the required amount of fluid before Can only be exchanged by technically trained
CHARGE LEVEL starting the Vectrix. authorized service agent and are not subject for
Look at the charge level on the right LCD module. exchange in the field.
If there are less than four (4) bars showing, we Interlocks
suggest you recharge before use.
CUT-OFF SWITCH
STANDS UP The cut-off switch needs to be in the “on” (run)
Make sure both the side stand and center stand (if position.
applicable) are up (retracted).
SIDE STAND SWITCH
LIGHTS AND INDICATORS Make sure the side stand is in the upright position.
When you turn the key to “System On,” you will
notice that the entire instrument panel illuminates. CENTER STAND (OPTIONAL)
After a few moments all malfunction light telltales Make sure the center stand is in the upright
should go off. If they do not go off, have your Vectrix position.
checked at a dealer. Replace the headlight bulb if it
has burned out before riding. “READY” INDICATION
When you turn your key to the “System On” position,
you will see the “Ready” icon in the left Liquid Crystal
Display (LCD), provided all of the interlocks are
satisfied. The “Ready” icon means that the system
is ready to be enabled.

VECTRIX ZEV OWNER’S MANUAL 25

 Braking
The Vectrix Zero-Emission Vehicle includes a PROPER BRAKING
patented regenerative (regen) braking throttle Always ‘cover’ the front brake lever with the index
which is easy to use and will improve your riding and middle fingers of your right hand when using
experience. In the regen mode the motor acts as a regenerative braking to slow the vehicle. This will
generator to apply a load/braking to the rear wheel ensure that you are ready to apply the front brake
while returning energy into the battery pack. if it becomes necessary to slow the vehicle more
quickly. Never use the rear brake lever (on the left
FRONT BRAKE LEVER handlebar) by itself or with regenerative braking
To operate the front brake, pull the right hand without also using the front brake lever (on the right
brake lever towards the twist grip. The braking is handlebar). Using only the rear brake may result in
hydraulically operated, so you need not pull hard on the rear tire sliding, particularly when regen is used.
the lever. Instead squeeze steadily and smoothly. Be ready to pull both the front and rear brake levers
(which actuate the front and rear disc brakes) at all
REAR BRAKE LEVER times while riding, including while using regenerative
To operate the rear brake, pull the left hand brake lever braking. See the REGEN section of this Manual on
towards the twist grip. The braking is hydraulically Page 14 for proper use of regenerative braking.
operated, so you need not pull hard on the lever.
Instead squeeze steadily and smoothly.

26 VECTRIX ZEV OWNER’S MANUAL

 Rear Brake Lever Front Brake Lever Braking

Warning!
You should always use both brake levers for the most effective braking. One lever will not provide you as
effective braking power.

Never brake suddenly or in a harsh manner. This could cause the wheels to lock and you could lose control
of the Vectrix. Bad weather, including slippery wet road, can cause braking to be less effective. Always
use caution in wet conditions. Low tire pressure can reduce braking effectiveness, so checking your tire
pressure is very important.

VECTRIX ZEV OWNER’S MANUAL 27

 Parking the Vehicle
n Stop the Vectrix and put either the side or center
stand down for support

n Turn the handlebar all the way to the left and

lock it there by turning the key to the “lock”
position.

n Park the Vectrix in a area visible to other

motorists.

n Never park on soft earth.

Warning!
The use of padlocks that prevent motion is very
dangerous and can affect the operation of the
Vectrix. If you use a padlock to secure your Vectrix,
the padlock must be removed before operating the
Vectrix.

28 VECTRIX ZEV OWNER’S MANUAL

 Charging the Battery
The Vectrix includes an 8ft (2.4m) charging cord The speedometer indicates the charge current times
which is located in the trunk under the passenger Warning! (X) 10 on the KPH scale.
seat. For example, 110 KPH indicates 11 amps.
Use extreme caution when dealing with electricity.
The male connector on the charging cord is specific Use RCD or GFI protected outlet.
to the country of use. For instance, in Italy the
plug consists of a 4-conductor assembly. This
accommodates “hot,” “neutral,” “ground” and a Warning!
“pilot” pin. In this case the pilot pin is used by the
AC power source (charging station) to detect the Though it is not recommended by Vectrix, if you
presence of the Vectrix, which in turn enables the use an extension cord to charge the bike, make
stationary power outlet. sure that it is at least a 20A cord and it should be
no longer than 25ft (7.6 m) in length.
To charge the Vectrix, open the trunk, remove the Charging Cord
cord, close the trunk taking care to route the cord While the bike is charging, the instrument cluster
through the designated slot in the bodywork and plug will display several charge status items. On the left
the electric two-wheel vehicle into an appropriate LCD the ‘estimated range’ field indicates the battery
120v/60Hz 220v/50Hz outlet. Once plugged in, voltage. The ‘trip’ field indicates the highest battery
the onboard charger will automatically control the module temperature and the ‘clock’ field indicates
charging process. During the charging process, the total charge time or time remaining during the
battery charge icon on the left LCD will be active. As transition mode.
the charge progresses, the battery level indicator on On the center LCD, the ‘odometer’ field indicates
the right LCD will increase in level. the charge mode and the voltage limit. The charge
modes are:
The charge is complete when all bars have been ‘CP’ = constant power,
filled on the right LCD on the instrument panel. It is ‘TR’ = transition mode,
perfectly fine to unplug the Vectrix from the outlet ‘CC’ = constant current and
and interrupt the cycle. The Vectrix will benefit by ‘EC’ = end of charge.
any amount of charging you have time for.

VECTRIX ZEV OWNER’S MANUAL 29

 Maintenance
Although your Vectrix requires little maintenance,
it is important that you read and follow closely the
maintenance items identified in this Manual as well as
in the Warranty Book.

Warning!
If you are unsure of the problem with your Vectrix,
take it to an autorized dealer to get it checked out or
call 1-877-VECTRIX (832-8749).

30 VECTRIX ZEV OWNER’S MANUAL

 Battery Pack
If you notice any discharge coming from your Vectrix
take it to a service center to get the system checked.

Warning!
The Battery Pack is rated at 125 Volts, 30 Amp
hours. Contact with the terminals of the Battery
Pack can result in injury or death.

The onboard smart battery charger monitors the

status/condition of the Battery Pack during normal
operation as well as charging. The Battery Pack is an
integrated system of temperature/voltage monitoring as
well as cooling airflow/control. The charger will detect
any underperformance in the Pack and automatically
perform an “Equalization Charge” of the battery. Such
an event will be seamless to the operator, except that
the charge time will be extended beyond the 3 to 5 hour
typical charging time.

If you have been running the Vectrix for a long period

of time and your battery is very hot, you should wait
until it cools down before charging, as the battery
will take longer to charge when it is very hot (optimal
temperature for charging batteries 25° C/ 77° F).
Depending on the conditions, waiting 1 – 2 hours after
riding before charging is sufficient.

VECTRIX ZEV OWNER’S MANUAL 31

 Checking Brake Fluid Level
Your brake fluid should never go below the MIN mark
on the reservoir. Air can enter the reservoir if the
fluid level is below MIN. This could cause problems
in your Vectrix system. Brake fluid should always
be topped off and changed on a routine basis. The
brake fluid reservoirs are located on the handlebar
assembly.

It is recommended that the brake fluid be changed MIN

every two years.

If you find excessive play on the brake lever but the

brake pads are still in good condition, you should go
to an autorized dealer at your earliest convenience to
get the system checked.

Warning!
Brake fluid may damage the Vectrix paint and
plastic parts if accidentally spilled. Brake fluid can
cause damage and injuries if not handled properly
and safely. If the brake fluid gets on your skin, you
should wash it off immediately with running water.
If the brake fluid gets into your eyes, flush them
with running water and seek medical attention.
Never mix old and new fluid. Always check for
proper sealing.

32 VECTRIX ZEV OWNER’S MANUAL

 Checking Brake Pads for Wear
Front Brake
Brake pads have a wear mark. If the grooves in the
friction material are visible, the pad is not worn.

Rear Brake
The rear brake pad material should be at least 1mm
thick for effectiveness.

Note!
See your autorized dealer for brake replacement.

VECTRIX ZEV OWNER’S MANUAL 33

 Bulb Replacement

Warning!
Do not change bulbs immediately after running
your Vectrix. Let the lights cool off. Bulbs become
hot when the Vectrix is running and need proper
time to cool off. Hot bulbs can cause severe burns
if handled.

Headlight
To replace the headlight bulb, you will need to work
behind the headlight fairing. Remove the connector
from the bulb. Pull the tab to remove the protective cap.
Release the clip that holds the bulb in place and take the
bulb out of the socket. The headlight is a dual filament 2
X 35 watt Phillips HSR-1.

Note!
Always hold the new bulb from the base. Oil from
human hands can cause the bulb to turn black and
become less brilliant.

LED LIGHTING SYSTEM

Due to the extremely long life of the LED lighting
system, individual LED replacement is not expected.
If a turn signal, stop/tail light, license plate light or
trunk light fails, it is necessary to replace the entire
lighting module which has failed.

34 VECTRIX ZEV OWNER’S MANUAL

 Beam Setting
The Vectrix must be in an upright position to check CORRECTING THE LIGHT BEAM
the beam setting. Make sure the tires are at the The Vectrix main/dipped beam has been precisely
proper inflation. Have one person sit on the Vectrix. set at the factory. Please contact your authorized
Place the Vectrix opposite a wall, about 10 meters Vectrix dealer if resetting is required.
away. Draw a horizontal line dictated by the headlight
center and a vertical line in line with the Vectrix axis.
It is better to perform this test in dim light. Switch on
the low beam. The height of the light spot should not
exceed 9/10 of the height from ground to headlight
center.

VECTRIX ZEV OWNER’S MANUAL 35

 Fuses

Warning!
Any and all fuses need to be serviced by an
autorized dealer. Do not attempt to change these
fuses, or you could cause injury or death to
yourself and others.

The fuse protection scheme for your Vectrix limits

access to the fuses to an authorized dealer. You
should not attempt to change any fuse on your
Vectrix.

36 VECTRIX ZEV OWNER’S MANUAL

 Tires
PROPER PRESSURE FOR YOUR FRONT AND REAR
TIRE Note!
Tire pressure changes with the temperature and by
altitude. You should check the pressure on your tires Low tire pressure can result in decreased range
often to ensure a safe ride. The front tire should be performance. Always check tire pressure to keep at
at 32 psi (2.2 bar) and the rear wheel should be at optimal performance.
40 psi (2.8 bar). If you find that the pressure in your
tire is always low and quickly changes from high
to low after being filled with air, see your autorized
dealer to inspect the tire.

REPAIR AND REPLACEMENT OF TIRES

Tires should be checked by an autorized dealer on a
regular basis to ensure that they have enough tread
and are not damaged or punctured in any way. If
you have any questions about your tires, see your
service agent for advice and help.

Warning!
You should replace tires with the standard size
recommended. You should avoid larger tires than
the recommended size. Failure to do this could
result in injury or death.

Note!
Always have the tires balanced after replacing them.

VECTRIX ZEV OWNER’S MANUAL 37

 Tires
Proper tread depth
It is recommended to replace the tires when the tread Warning!
is below 2 mm.
Driving on tires with little or no tread is dangerous
and could cause an accident. Checking your tread
depth is extremely important. Failure to do so
could result in riding on bald tires, which can cause
injury or death, especially in wet conditions.

38 VECTRIX ZEV OWNER’S MANUAL

 Cleaning
Washing your Vectrix Once the dirt has been completely removed, rinse off Waxing Your Vectrix
As with any vehicle it is important that you wash the detergent with running water. After washing your Vectrix, waxing and polishing are
your Vectrix on a regular basis to keep the finish recommended to further protect and beautify the
in good condition. Never use harsh detergents or After rinsing, wipe off your Vectrix with a wet paint.
abrasive cloths on your Vectrix. chamois or clean cloth (clean cloths will minimize n Only use waxes and polishes of good quality.
scratching) and allow it to dry in the shade. n When using waxes and polishes, observe the
When washing your Vectrix, follow the instructions precautions specified by the manufacturer.
below: Check carefully for damage to painted surfaces. If
there is any damage, obtain “touch-up” paint and
Remove dirt and mud from your Vectrix with running “touch up” the damage.
WARNING
water. You may use a soft sponge or brush. Do not
Wet brakes can cause poor braking performance
use hard materials which can scratch the paint. Windshield Cleaning
and may lead to an accident.
Clean the windshield with a soft cloth and warm
Avoid a possible accident by expecting longer
Wash the entire Vectrix with a mild detergent or car water with a mild detergent. If scratched, polish with
stopping distances after washing your Vectrix.
wash soap using a sponge or cloth. The sponge or a commercially available plastic polish. Replace the
Apply brakes several times to let heat dry the
soft cloth should be frequently soaked in the soap windshield if it becomes scratched or discolored so
brake pads or shoes.
solution. as to obstruct view. When replacing the windshield,
use a replacement windshield from Vectrix.
CAUTION NOTE!
CAUTION
When cleaning, you should avoid using a pressure Always allow your Vectrix to fully dry before using
washer or high pressure water unit. These units Cleaning with any alkaline or strong acid cleaner, it.
could damage your Vectrix. gasoline, brake fluid, alcohol or any other solvent
will damage the windshield.
Clean only with a soft cloth and warm water with
NOTE! a mild detergent.

Avoid spraying or allowing water to flow over the

following places:
• Ignition Switch
• Break master cylinders

VECTRIX ZEV OWNER’S MANUAL 39

 StorING
If you plan on storing your Vectrix for an extended
period of time, follow these procedures: NOTE!
n Clean the Vectrix and allow it to dry before Do not use the plastic around the handlebars
storing. or the throttle area to secure the Vectrix for
transporting.
n Place the Vectrix on a service stand.

n Check the Vectrix for problems every few

weeks.

n A cover protects the Vectrix from the elements

and is a good investment.

n The Vectrix must be fully charged and turned off

prior to storage.

n You should not store your Vectrix for more than

three months without re-charging the battery.

The Vectrix battery will become damaged if the above

precautions are not followed.

TRANSPORTING:
If you need to secure your Vectrix onto a pallet or
another vehicle for transporting, it is recommended
that you make use of the two ‘D’ shaped rings at the
base of the front fork triple clamp for securing the
front end of the bike and the rear of the bike can be
secured through the swing arm.

40 VECTRIX ZEV OWNER’S MANUAL

 D-rings
TRANSPORTING

WARNING!
Take special care of the brake hose DO NOT
CRUSH or place the belt above the swing arm.
This can cause possible damage and may result
in unsafe conditions. Carefully place the belt
under the hose and take special care NOT to pull
the brake hose too hard to weaken the connection.
See photo

Representative tie down - front and back. D-ring locations as seen from under the bike.

Brake
Hose

Rear non-brake side: Protect the swingarm cutting Rear brake side
edges (one side)

VECTRIX ZEV OWNER’S MANUAL 41

 Troubleshooting
All of our bikes are carefully inspected before they are delivered to the customer. Even after the bikes are inspected, some technical problems can occur. The following
chart offers a guide for you to identify a problem and, if possible, fix it yourself. If you are unable to solve a problem with your Vectrix, take it to an authorized Vectrix
technician at your convenience.

42 VECTRIX ZEV OWNER’S MANUAL

 Troubleshooting
Symptom Potential Cause Potential Solution
Scooter does not turn on Key not properly engaged Recheck key in ignition, turn off/on again
Scooter on but no ‘ready’ light Power on/off switch not engaged Recheck switch, turn off/on
Scooter plugged in to AC Unplug scooter and store plug fr riding
Throttle not set Call Vectrix authorized dealer for instructions
Ready light flashing Side stand switch not engaged Check stands/deploy and retract/check connection
Charger not working A/C power missing Check A/C outlet for power, A/C source check fuse/voltage
Premature charge termination Charger and battery unsynchronized Run bike until battery icon blinks and fuel gauge resets to ‘0’ and charge bike.
Charger firmware out of date Call dealer for service. Technician must determine charger firmware revision and
update minimum Rev 2012, or thereafter.
Handlebars wobble (shimmy) Tire pressure Inflate to correct tire pressure (see tire section)
Deformed front tire Replace / balance front tire with the same tire supplied from the factory
Bald tire (excess wear) Replace / balance tire with the same tire supplied from the factory
Cargo box installed Check the bike behavior without cargo box. Never exceed the maximum load
allowed in the cargo box.
Flashing wrench / battery No charger output Contact your authorized dealer
Flashing wrench / battery / Battery air-plenum Contact your authorized dealer
temperature
Flashing temperature / battery Battery temperature greater than 50°C Contact your authorized dealer
Or
Battery temperature sensor data error
Flashing battery Shorted cell
Or
15°C temperature difference at once sensor
compared to the average temperature of the
battery pack

VECTRIX ZEV OWNER’S MANUAL 43

 Specifications
WARRANTY: CHARGER:
Standard is twenty-four months 1.5 kW on-board battery charger

EMISSIONS: RECHARGE REQUIREMENTS:

Zero* 110V-230V (50/60Hz)

WEIGHT: RECHARGE TIME

515 lbs. (234 kg) 3-5 hours

SEAT HEIGHT: BATTERY DEEP DISCHARGE CYCLES

30.5” (774 mm) (80% CHARGE):
1,700
STORAGE CAPACITY:
Under-seat storage for one full-faced helmet, glove ESTIMATED BATTERY LIFE:
compartment below dash 50,000 MILES / 80,000 km

MOTOR TYPE: BRAKING:

Brushless DC radial air-gap motor Patented multi-function throttle provides regenerative
Peak Power: 21 kW peak power at motor shaft braking and slow speed reverse with Brembo
Max Current: 275 Amps mechanical brakes front and rear
Max Torque: 65 Nm
GROSS VEHICLE WEIGHT:
GEARBOX: = 938 lbs. (425 kg)
Integrated rear-wheel mounted planetary gear drive
TIRE PRESSURE
BATTERY TYPE: Front: 32 psi (2.2 bar)
Nickel Metal Hydride (NiMH) Rear: 40 psi (2.8 bar)

RATED BATTERY CAPACITY: *in operation

30 Ah, 3.7 kW-h

RATED BATTERY VOLTAGE:

125V
44 VECTRIX ZEV OWNER’S MANUAL
 RANGE
Fundamentals of Vectrix Range Operating under constant speed conditions our 1. Does acceleration affect range?
The range of an electric vehicle is defined as the data indicates the following averages: Acceleration is the rate which you are attempting
distance the vehicle will travel on a single full to increase the speed of your Vectrix. The greater
charge of the battery pack. Just like EPA mileage Constant Speed Range the acceleration the faster you are depleting the
estimates on automobiles “your mileage may 25 mph (40 km/h) 65 miles (105 km) energy in the battery pack. The harder and more
vary”. Your range results are a direct reflection of 35 mph (56 km/h) 54 miles ( 87 km) frequently you accelerate the more adversely you
your driving habits. The more conservative you 40 mph (64 km/h) 48 miles ( 77 km) will affect the range of your Vectrix. Being “first
ride the better the range you can expect from your 45 mph (72 km/h) 44 miles (71 km) off the line” means you will also be the first to
Vectrix. 50 mph (81 km/h) 36 miles ( 58 km) drain your energy supply.
60 mph (97 km/h) 20 miles ( 32 km) Hard Acceleration = Reduced Range
Some of the factors which affect range include
speed, acceleration, number of star ts & stops, In a typical urban driving environment with traffic, 2. Does weight affect range?
as well as changes in elevation. The combination traffic lights and varying driving conditions you The Vectrix at approximately 500 lbs (226.8 kg)
of these factors, as you travel from one point to should expect to travel between 30 to 45 miles plus a 180 lb (82 kg) driver equates to a gross
another, defines your trip profile. In addition tire on a single battery charge. During constant speed vehicle weight of 680 lbs. (308 kg) If you add
pressure and payload are impor tant considerations. driving on a level surface the Vectrix consumes 50 lbs (23 kg) of cargo the total weight you
Our range testing involves the equivalent of a approximately 39 wh/km @ 40km/hr. are attempting to move is 730 (331 kg) pounds
180 lb (82 kg) driver with no passenger or cargo or 7.3% increase in weight. If then you add a
driving on a flat/level surface. We suggest that you drive conservatively when you 175 lbs (79 kg) passenger the total weight is
first get your Vectrix and get to know your bike and 905 lbs (411 kg) or a total weight increase of
Since there are an unlimited number of potential trip your commute. Once you become familiar with the 33%! The more mass you are pushing/lifting the
profiles we provide typical range estimates based range versus performance of your bike then you can more energy it takes to accomplish the mission.
upon driving the Vectrix at a constant speed. We adjust your driving characteristics if you so desire. Avoid keeping unnecessary items in your Vectrix
have tested the Vectrix at constant speeds both This applies mainly to drivers with trip profiles which since it will impact your range.
on test tracks and dynamometers to establish are at the edge of the range envelope. Those of you Added Weight = Reduced Range
the range performance estimates of the bike. with relatively short commutes can expect to ride
Remember that a constant speed trip/test involves quite aggressively and reach your destination with
a single acceleration to the constant speed and a energy to spare.
simple stop at the end. No one actually drives on
public roadways under these conditions however
it does provide a basis for comparisons.

VECTRIX ZEV OWNER’S MANUAL 45

 RANGE
3. Why do I get less range at higher At Vectrix we understand the exhilarating feeling
speeds? you get from aggressive acceleration in either the
It takes more energy to push a Vectrix faster forward or regenerative braking modes. This is
because you encounter aerodynamic resistance. very special machine with unique performance
The faster you attempt to travel the more characteristics. However, if maximizing range is your
important this factor becomes. Also it is a primary objective, we suggest you drive sensibly and
fundamental characteristic of battery energy conservatively since it will extend your range and
storage systems that the amount of energy you provide a safer ride for you and those around you.
are able to extract from the battery is inversely
proportional to the rate at which you drawing
out the energy. If a battery pack is rated for
30 Ah if you draw 10 amperes of current you
will deliver more energy that if you are drawing
100 amperes of current. Bottom line is that the
more conservative you drive the further you will
travel on a single charge.
Faster Speed = Reduced Range

4. How does tire pressure affect range?

As the Vectrix is ridden, heat is generated in the
tires from deformation at the contact patch. Higher
inflation pressure reduces this deformation,
which results in reduced heating of the tire and
reduced energy loss. A tire that is at 2/3 the
proper inflation pressure will have as much as
30% greater rolling resistance than a tire inflated
to the specified pressure. This difference can
easily be felt when moving the vehicle manually.
More force is required to move the vehicle when
tire pressure is low. Keep the tires inflated to the
specified pressure to maximize range.
Incorrect Tire Pressure = Reduced Range
46 VECTRIX ZEV OWNER’S MANUAL
 Performance Data
MAX SPEED: WHEELS:
62 mph (100 km/h) Front: 120/70 -14”; Rear: 140/60 -13”

OPERATING TEMPERATURE: WHEELBASE:

14°F - 122°F (-10°C to 50°C) 60” (1,525 mm)

ACCELERATION: CONTROLLER:
0-50 mph (80 km/h) in 6.8 seconds DSP and IGBT based all-digital electronic control and
motor drive system
RANGE:
35 miles (56 km/h) -55 miles (89 km/h) in average INSTRUMENTATION:
driving conditions LCDs display speed, odometer, energy consumption,
battery status, estimated range and system status
MAX RANGE:
65 miles (105 km) @ 25 mph (40 km/h)

FRAME:
Lightweight aluminum frame

WEIGHT ALLOWANCES:
Underseat / Trunk Capacity
26 lbs. (12 kg)

Glove Box Capacity

4 lbs. (2 kg)

Cargo Box and Contents

not to exceed 20 lbs (9 kg)

VECTRIX ZEV OWNER’S MANUAL 47

 For USA Versions Only SWITZERLAND CUSTOMERS
SAFETY DEFECTS The key switch turns off all of the power supplies
Contact the National Highway Traffic Safety that feed the control electronics. This makes it
Administration (NHTSA) if you believe that this vehicle impossible for the control electronics to synthesize
has a defect that could cause an accident, injury or the waveform required to make the motor run.
death. Also contact Vectrix Corporation immediately.
If the NHTSA receives multiple complaints, it could
lead to an investigation. The NHTSA may opt to
recall vehicles if it perceives a safety threat. The
NHTSA cannot deal with individual problems with
dealerships or Vectrix Corporation.

THE NHTSA CAN BE REACHED AT:

1-800-424-9393

OR YOU CAN WRITE TO THEM AT:

NHTSA
US Department of Transportation
Washington, DC 20590

END OF US REQUIREMENTS

48 VECTRIX ZEV OWNER’S MANUAL

 LABEL LOCATIONS
The following pages (50-51) display the locations of
safety labels and the labels themselves. 2

3
1

VECTRIX ZEV OWNER’S MANUAL 49

 For USA Versions Only

WARNING
Your Vectrix is equipped with a warning light when the
side stand is lowered (on).

However, it is the rider’s responsibility to ensure that

the side stand is stowed completely before starting
out.

Failure to observe this warning could result in an upset

and consequent bodily injury.

NOTICE

Accessory Port
12 VDC 0.5 AMPS (6 WATTS)
MAXIMUM

1
Label not visible without removing seat.

50 VECTRIX ZEV OWNER’S MANUAL

 Routine Maintenance Record

DATE OF SERVICE MILEAGE SERVICE DESCRIPTION COMMENTS

VECTRIX ZEV OWNER’S MANUAL 51

 NOTES

52 VECTRIX ZEV OWNER’S MANUAL