180

BENGARD
The one thing that has remained constant over our 40 years is Bengard's commitment to excellent customer service.
At Bengard, this means meeting our customer's requirements in all aspects of the business. Our dedication to the ideal,
inspired by a complex and constantly evolving marketplace, has led us to specializing in the area of Flooring Transition
Mouldings. We are proud to introduce our 2009 Product Catalogue. The information in this catalogue is gathered from
customers, end users, and our personal experiences. The products have been created to provide you with solutions from
today's transition challenges.

We'd like to thank you for your patronage and for giving us the opportunity to become "Your Floor Moulding Specialist".
Being "Your Floor Moulding Specialist" means...

... We will provide the best service in the industry, by utilizing a team of dedicated Customer Service Specialists.

... Our product will maintain a high degree of consistency and quality to meet the needs of our customers, by manufacturing
our product to ISO Standards.

... We will incorporate our customers input when making decisions, by using ideas and suggestions brought to us.

... All our business dealings will be handled with integrity, by ensuring customers and suppliers alike know the facts.

... New product innovation will be an integral part of our business strategy, by continually anticipating market trends and
designing the transition solutions demanded by the industry.

WARRANTY
BENGARD LIMITED WARRANTY
Bengard Aluminum, Vinyl and Rubber modified flooring products, for a period of 1 (one) year from date of shipment, will be subject to the following
warranties; Bengard products will conform to original product and contract description with only such reasonable variations as is acceptable in the trade .
These products will be fit for the purposes for which they were intended and that they will be adequately packaged and labeled. Bengard will replace any
defective product found if said defect is identified before installation. If a defect is found after installation, Bengard must be notified in writing within 10 days
of installation. The customer must then, at Bengard's discretion, allow an inspection of the installation. If upon inspection, Bengard determines the product to
be defective, Bengard will at its own discretion supply replacement materials that conform to the contract requirements or issue a credit equal to but not
exceeding the original purchase price for the goods in question. Bengard assumes no liability or responsibilities for labour or the cost of other materials used
in such installations.

Warranties do not apply to the following specified items, terms and conditions: A) Exact matching of color, shade, texturing or mottling.
B) Any warranties, other than expressed above, implied or promised by any sales representative. C) Tears, scratches, burns, or other damage caused by
improper installation, improper use or maintenance. D) Sales of "Seconds", or "Imperfect" goods. E) Problem caused by moisture, hydrostatic pressure or
alkali in the sub-floor. F) Problem caused by installation with non-approved adhesive. If you are unsure about the suitability of a particular adhesive, please
call us for our recommendations. G) Product installed - Outdoors. Bengard products are designed for interior use only. H) Color degradation caused by
sunlight or other U.V. exposure. These warranties are supplied in lieu of any other warranty, expressed or implied. All product specifications are subject to
change without notice.
 180

BENGARD
Table Of Contents
SECTION
1 Vinyl/Rubber Products

SECTION
2 Aluminum/Carpet Products

SECTION
3 Laminate Products

SECTION
4 Ceramic Tile Products

SECTION
5 Wood Mouldings

MORE INFORMATION

COLOUR GUIDE...............34

LEGEND..........................34

NUMERICAL INDEX...........32

WARRANTY........................1

2
 SECTION 1
VINYL WALL BASE VINYL BASE
.080” .080” High quality Cove Base manufactured
using 100% Virgin materials.
.080” .080”
Advanced co-extrusion technology
6” 6” allows for tough scuff-resistant surface
while maintaining overall flexibility
.080” .080”
and ease of installation.
4” 4”
Unique "V-Groove" glue lines
provides greater surface area on
2 1/2” 2 1/2” back of base for vastly improved
SECTION

ESSENTIALS
contact area.

Top Return ensures close fit to wall.

The compounds used consists of

VX 250 TX 250 VX 400 TX 400 VX 600 TX 600 durable high resin Vinyls.
• 2 1/2" Vinyl Cove Base. CX 400 • 6" Vinyl Cove Base.
• 0.080" Gauge. • 4" Vinyl Cove Base. • 0.080" Gauge. VX Series Cove Base is available in
• 120' per CTN/ Rolls or 4' Strips. • 0.080" Gauge. • 120' per CTN/ Rolls or 4' Strips. all 36 colors to coordinate with other
• 120' per CTN/ Rolls or 4' Strips. Bengard Vinyl Mouldings

We welcome your custom color

Pre-Moulded outside corners are inquires. Certain minimums apply.
available in 2 1/2" , 4" ,6" heights
and in all colors. Please specify RX, 1/8" Vinyl Wall Base also available.
or VX along with size and color. RV250, RV400, RV600 Special
Order Only

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only
For colour availability please refer to Colour Guide/Legend on pg. 31 & 32

RUBBER WALL BASE

1/8” 1/8” RUBBER BASE
Our Premium Cove Base product.

Manufactured using 100%

1/8” 1/8”
Virgin material.
6” 6”
Advanced co-extrusion technology
allows for tough scuff resistant surface
1/8” 1/8”
while maintaining excellent overall
4” 4” flexibility and ease of installation.

Thick 1/8" gauge covers most

wall imperfections.
2-1/2” 2-1/2”
ESSENTIALS
Unique "V-Groove" glue lines provide
greater surface area on back of base
for vastly improved contact area.

Top Return ensures close fit to wall.

RR 250 TR 250 RR 400 TR 400 RR 600 TR 600 1/8" Wall Base also available
• 2 1/2" Rubber Cove Base. • 4" Rubber Cove Base. • 6" Rubber Cove Base. in Vinyl.
• 1/8" Gauge. • 1/8" Gauge. • 1/8" Gauge.
• 120' per CTN/ Rolls or 4' Strips. • 120' per CTN/ Rolls or 4' Strips. • 120' per CTN/ Rolls or 4' Strips.

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only
3
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
 SECTION 1
COLONIAL BASE SCULPTURED WALL BASE
Colonial Style Base is a flexible,
PVC wall base that replicates painted,
sculpted wood base moulding.

Colonial Style Base is more

cost-effective than traditional wood
base and is great for remodel or
new construction in commercial and
industrial settings. It is dent and
scratch resistant and requires
no painting. EB450 QR6875

Colonial Style Base's flexibility makes Heavy gauge rubber base. Dent and water resistant, super strong
it great for straight or curved walls Smooth satin finish and intrinsic flexibility self adhesive with no nails or caulking
while hiding imperfections. helps hide substrate irregularities. required. Product adheres to all clean
Available in continuous rolls. and dry surfaces. Saves installation time,
The 4 1/2" height covers over
Available in white. easy to cut and paintable.
previous 4" base installations for Deep grooves and several uniquely-shaped
a clean, fresh look. surfaces simulate milled wood mouldings. Available: WHT

50 foot seamless rolls are perfect for Available: WHT

large areas. Making straight,mitered, 11/16”
or inside and outside corners are
4-1/2”
easily done.
11/16”
No nailing, priming, painting needed.
Base will stand firm against dents,
scratches, mildew, and cracking.

SECTION 1
RUBBER BASE SPECIFICATIONS
Flooring accessories shown in the finishing schedule as RUBBER WALL BASE shall be
high resin content rubber modified wall base as manufactured by BENGARD
MANUFACTURING. All rubber base shall be a height of___(Specify 2 1/2", 4", or 6")
and a length of ____(Specify 4 foot strips or 120 foot coils) in ___(Specify toe or toeless)
Top Return
style. The wall base shall conform to the performance specifications of CSA-A126.5 and
to Federal Specification ASTMF1861-98. The wall base shall be supplied free of surface
blemishes and imperfections. Only premium quality wall base adhesives will be used for
installing this product. Use of any other adhesive will void the BENGARD warranty.

V-Groove
VINYL BASE SPECIFICATIONS Glue Lines
Flooring accessories shown in the finishing schedule as VINYL WALL BASE shall be high
WALL

resin content vinyl wall base as manufactured by BENGARD MANUFACTURING.

All vinyl base shall be a height of___(Specify 21/2", 4", or 6") and a length of ____
(Specify 4 foot strips or 120 foot coils) in ___(Specify toe or toeless) style. The wall base
shall conform to the performance specifications of CSA-A126.5 and to ASTM F1861-98.
The wall base shall be supplied free of surface blemishes and imperfections.
Only premium quality wall base adhesives will be used for installing this product. Adhesive
Use of any other adhesive will void the BENGARD warranty.

4
 SECTION 1
TRACKS FOR E+T CAPS

CM1651 CM1655
CM1651P, CM1130 CM1655P, CM1140 CM1658 CM1659 CM1660

Narrow Pinless Channel for Wide Pinless Channel for use For areas where extra strength 5/8" Aluminum Narrow 5/8" Aluminum Pinless
use where rubber backed where rubber backed or glue or height is needed. Can be Channel for areas where
SECTION

Pinless Channel for areas

carpet meets dissimilar flooring. down carpets meets dissimilar used with all 1/8" leg "E" or where extra strength or extra strength or height is
Accepts all 1/8" leg "T" or flooring. Accepts all 3/16" "T"caps. Extra height for height is needed. Can be needed. Can be used with
"E"caps such as Bengard's leg "T" or "E" caps such as installations where floor used with all 1/8" leg all 3/16” leg E or T caps.
CM1110,CM1120, Bengard's CM1150,CM1151, covering are over 3/8" high "E" or "T" caps. Extra Extra height for installations
CM1111,and CM1121. CM1161,CM1171,CM1180, but less than 1/2". Added height for installations where floor covering are
Canadian Style Channel. and CM1181. U.S. Style strength of one piece aluminum where floor covering are over 3/8” high but less
CM1651P is same as Channel. CM1655P is same track holds up under increased over 3/8" high but less than 5/8”. Added strength
CM1651 except bottom as CM1655 except bottom traffic. Tack strip can be used than 5/8". Added strength of one piece aluminum
flange is pre-punched for easy flange is pre-punched for easy when installing under pad of one piece aluminum track holds up under
setting into mortar for ceramic setting into mortar for ceramic Finish: MIL track holds up under increased traffic. Tack strips
tile application. CM1130*is tile application. CM1140* is increased traffic. Tack strip can be used when installing
made of rigid PVC. made of rigid PVC. can be used when under pad.
Colour: WHT Colour: WHT installing under pad. Finish: MIL
CM1130 Finish: BLK CM1140 Finish: BLK Finish: MIL
Finish: MIL Finish: MIL

3/32” 3/32” 5/32”

3/32” 5/32” 5/8”

1/2” 5/8”
3/8” 3/8”
1-1/4” 1-1/4” 1-1/2” 1-1/2” 1-1/2”

CM1751 CM1752 CM1755 CM1759 CX1000 CX1100

Channel for use where action Same as 1751 except for step Wide channel for use for 3/4” Aluminum Wide Pinned Channel Extender. Made of
backed carpet meets dissimilar on base of channel. The step where action backed carpet Channel for areas where extra Rigid PVC. Used on ceramic tile
flooring. Accepts all 1/8" leg is useful for tucking-in high pile meets dissimilar flooring. strength or height is needed. installations when inserted into
"T" or "E" caps such as Bengard's carpet. Ultra Pin continuous Accepts all 3/16" leg "T" or Can be used with all 1/8” leg track. This extender increases
CM1110,CM1120,CM1111, pinning system for maximum "E" caps such as Bengard's “E” or “T” caps. Extra height for effective height of channel by
and CM1121. Ultra Pin holding strength. Accepts all CM1150, CM1151, installations where floor covering 3/8”. For use in U.S Style
continuous pinning system for 1/8" leg "T" or "E" CM1161,CM1171, are over 3/8” high but less than channels such as CM1755,
maximum holding strength. caps such as Bengard's CM1180, and CM1181. 3/4”. Added strength of one CM1655, and CM1140.
Canadian Style Channel. CM1110, CM1120, Ultra Pin continuous pinning piece aluminum track holds up Also for use in Canadian style
Finish: MIL CM1111,and CM1121. system for maximum holding under increased traffic. Ultra Pin channels such as CM1751.
Canadian Style Channel. strength. U.S. Style Channel. continuous pinning system for CM1752, CM1651, and
Finish: MIL Finish: MIL maximum holding strength. CM1130.
Finish: MIL CX1000 Finish:WHT
CX1100 Finish: BLK
5/32”
3/32” 3/32” 5/32”
CX1100 CX1000
3/8” 3/8” 3/8” 11/16”
1-3/8” 5/8” 5/8”
1-1/2” 1-1/2” 1-1/2”
1/8” 3/16”
5
 SECTION 1
VINYL E+T CAPS

CM1110 CM1120 CM1111 CM1121 CM1125

Regular E & T-Caps for use where adjacent floors Commercial E & T-Caps for use where adjacent Commercial E & T-Caps for use
meet and color coordination is important. floors meet and color coordination is important. where adjacent floors meet and
For residential or light commercial purposes. E - Cap for use on height differentials under 5/8". colour coordination is important.
Use with CM1651, CM1659, CM1751, Both made for high traffic commercial purposes. For residential or light commercial
or CM1752 Use with CM1651, CM1659, CM1751, purposes. Available in 12 foot
* Available in wood grain finish. or CM1752. lengths. Use with CM1651,
CM1751, CM1752,
CM1659 AND CM1658
Finish: Beech, Oak, Red Oak,
Walnut

1-1/2” 1-1/2” 1-1/2”

7/8” 7/8”

1/8” 1/8” 1/8” 1/8” 1/8”

CM1150 CM1165 CM1171 CM1151 CM1161

Regular E & T-Caps for use Commercial E--cap for use Regular E & T-Caps for use Commercial E & T-Caps for use where adjacent floors meet and color
where adjacent floors meet and where adjacent floors meet and where adjacent floors meet and coordination is important. E - Cap for use on height differentials under
color coordination is important. colour coordination is important. colour coordination is important. 5/8". Both made for high traffic commercial purposes. Fits wide
For use in residential to light Use on height differentials For use in residential to light channels such as CM1655, CM1755, CM1759, and CM1140.
traffic areas. Made for height under 5/8”. traffic areas. Made for height
differentials up to 3/8". Available in 12 foot lengths differentials up to 3/8”.
Fits wide channels such as Finish: Beech, Oak, Red Oak Fits wide channels such as
CM1655, CM1755, CM1655, CM1755,
and Walnut. 1-1/2” 1-1/2”
CM1759, and CM1140 CM1759, and CM1140.

1” 1-1/2”
1-1/2” 3/16” 3/16”
7/16”

3/16” 3/16”
3/16”

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
6
 SECTION 1
VINYL CAPS AND REDUCERS Our Commitment
Bengard was established in 1968 as B&B
Manufacturing, Bengard has the most
comprehensive product line in the industry,
including carpet, ceramic, laminate, vinyl, resilient
ESSENTIALS and hardwood trim. Bengard is a one-stop shop
for all of your accessory needs - your floor
moulding specialist.

CM1126 CM1181 The one thing that has remained constant over our
40 years is the Bengard's commitment to excellent
Regular E & T-Caps for use where adjacent floors meet and color coordination is important. customer service. At Bengard, this means meeting
SECTION

For use in residential to light traffic areas. Made for height differentials up to 3/8", our customer's requirements in all aspects of the
fits wide channels such as CM1655, CM1755, CM1759 and CM1140 business. Our dedication to the ideal, inspired by
a complex and constantly evolving marketplace,
has led us to specializing in the area of Flooring
1-3/8” Transition Mouldings.
1”

Our goal is to be the Global leader in

Floor Covering Accessories. This can only be
accomplished by offering great products, great
1/8”
3/16” service and by the actions of our associates.

ESSENTIALS

CM1200 RD2400 RD2330 RD2320

Carpet to Tile Divider for use Commercial carpet to ceramic or Carpet to Tile Reducer. Creates an Overlap Tile Reducer for use with
where commercial carpet meets hardwood Divider. For heavy duty attractive, safe transition between resilient flooring from
tile. Flexible lip allows use with traffic where ceramic or hardwood carpet and VCT. The edges of both 0.080 - 0.125” thick.
3/16” - 1/4” carpet meeting meet carpet. floor coverings can easily be tucked
0.080” - 1/8” tile. in to protect them from damage. The
bottom lip is designed to enable the
carpet and moulding to be glued
together and secured to the floor.

1/4” 1-5/8”
1” 1-3/8” 1-1/2”
1/4” 1/4”
3/8” 5/8”
7/8” 1-3/4” 5/8” 1-1/8” 1/8”

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only
7 For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
 SECTION 1
VINYL REDUCERS

RD2010 RD2020 RD2030, RD2040 RDV149

0.080" (2mm) Reducer Strip 1/8" (3mm) Reducer Strip RD2030 1/4" (6mm) h 1/4" Insert Reducer
for butting up to tile or for butting up to tile or RD2040 3/8" (9mm) h for glue down carpet
resilient flooring. resilient flooring. Reducer Strip for butting up installations. Can be used
Provides a smooth, safe Provides a smooth, safe transition to tile or resilient flooring. with carpet up to 28 oz.
transition to substrate or to substrate or adjacent flooring. Provides a smooth, safe Lip flexible up to 5/16".
adjacent flooring. transition to substrate or Also available with Peel
adjacent flooring. & Stick back, RDV149PS.

1/8” h”
.080”
1/4”
1” 1”
1-3/8”
1-11/16”

ESSENTIALS

RD2150 RD2130 RD2147 RD2148 RD2151

1/4” Insert Reducer for glue 1/4" Insert Reducer for glue 3/16", 1/4", 5/16" Tuck Reducer for glue down carpet installations.
down carpet installations. Can down carpet installations. Can For light commercial or residential use.
be used with carpet up to 40 be used with carpet up to 40 oz.
oz. Lip flexible up to 3/8”. Lip flexible up to 3/8".
For light commercial or For heavy commercial use.
residential use. Also available with 1/8" butt
RD2140, Special order

1-1/16” 1-11/32”
1-3/8” 1-1/4”
1-1/2” 3/16”
1/4” 1/4” 1/4” 5/16”

1-5/8” 3” 1-3/4” 2” 2-1/16”

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn)
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
8
 SECTION 1
VINYL STAIR NOSINGS

NS4010 NS4020 NS4023 NS4120 NS4024 NS4030

1 -5/8" Drop Overlap 1-7/8” Drop Overlap 2” Drop Overlap Nosing. 2" Drop Butt-Type Bull Nose designed to be Square Nose covers and
Nosing. Used over vinyl Nosing. Used over vinyl Used over vinyl Nosing. Used to butt up used with round nosed protects leading edge of
tile or resilient flooring. tile or resilient flooring. tile or resilient flooring. to 1/8" tile or resilient stairs. Flexible round stairs. Use over vinyl and
SECTION

Protects edge of floor Protects edge of floor Protects edge of floor floor. Protects edge of nose allows for easy sheet goods. Excellent slip
covering from damage at covering from damage covering from damage floor covering from installation. 5/8" return resistance. Smaller profile
step face and provides at step face and provides at step face and provides damage at step face helps to hide underside nosing provides a clean
extra traction for safety. extra traction for safety. extra traction for safety. and provides extra of stair. finished edge.
traction for safety.

1-1/2” 1-7/8” 1-7/8” 1-7/8” 1/8” 1-5/8” 1-3/8”

1-5/8” 1-7/8” 2” 2” 1-3/16” 1-1/8”

5/8”

NS4700 NT4220 NT4230 NS4310 NT4320 NT4330

Overlap Nosing 1-5/8" Drop 1-3/8" Drop not 1-3/4" Drop Double Butt Nosing. 1-3/4" Drop Commercial
This Rubber/Vinyl Commercial friction- including flange Commercial Single For butting up to carpet Nosing. Designed to butt
composite nosing has type insert nosing. commercial friction- Butt-Type Nosing. or tile. For use when to 3/8" ceramic tile,
large 2-1/2" x 2-1/2" For carpet or tile up double insert nosing. For butting up to 1/4" tile flooring is installed on providing excellent
legs to help cover to 3/8" thick. For carpet or tile up to or up to 30 oz. carpet. both step and riser. traction.
damaged area or stairs 3/8" thick.
with unusually large Also available with
drops. abrasive strip. Notched
for easy installation.

1/4” 1/4” 9/32” 9/32” 3/8”

2-5/8” 2” 2” 2” 2” 2-1/2”

1-1/2”
1-3/8” 1-3/4”
2-1/2” 1-3/4”
1-5/8” 1-1/32”

1/4” 1/16”

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only
9
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
 SECTION 1
VINYL STAIR TREADS

12-1/4”

5/32” 1/16”
2”

ST5010, ST5010SA,
ST5010DA ABRASIVE INSERT

ST5010 ST5010SA/ST5010DA ABRASIVE INSERT

Standard duty Stair Tread to suit most commercial applications
Safety grip top rib pattern
Available with single abrasive insert. Specify part #ST5010SA
Available with double abrasive inserts. Specify part # ST5010DA

12-1/4”
7/32” 1/8”

2” ABRASIVE
INSERT

ST5030, ST5030SA
ST5031
ABRASIVE INSERT

ST5030 ST5030SA ABRASIVE INSERT

Heavy duty Commercial Stair Tread
Safety grip top rib pattern
Available with one abrasive insert.
Specify part #ST5030SA.
Easy flex leg for set back risers

7-1/2”

SR5080
7-1/2" Stair Riser
6" Base may also be used as Stair Riser

ARCHITECTS' MATERIAL SPECIFICATION

ALL RUBBER/ VINYL STAIR TREADS supplied under this specification shall be BENGARD RUBBER/VINYL STAIR TREADS and are designated as (Specify ST5010,
ST5030. ST5030SA, ST5010SA, or ST5010DA for SAFETY GRIPS), and shall have a square nose that is 2" long as measured from the bottom of tread. The width of
the tread shall be 12-1/4" and a length of (Specify length up to 12 feet). The color shall be ..(Specify color from Bengard Color Chart). The Stair Tread will be installed
using only premium adhesives specifically designed to be used with stair treads and vinyl compatible. ST5010 and ST5030 are in full compliance with Federal
Specification RR-T-650 E, Composition B, Type 2 dated February 25,1994 superseding RR-T-650D, September 22,1988.

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn)
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
10
 SECTION 1
VINYL WALL CAPS

CC1010 CC1020 CC1060 CR2050PS

SECTION

1/4" Cove Cap for use when 1/4" Square Cove Cap for use 1/8" Square Cove Cap for use 1/8” resilient cove cap for use
coving carpet up to 5/16" thick. when coving carpet up to 5/16" when coving carpet up to 3/16" when coving resilient floor up to
thick and where a square look is thick and where a square look is 3/16” thick. Peel and stick tape
CC1010PS required. Available with peel and required. Available with peel and for easy application.
stick tape or dry back. stick tape or dry back.
ESSENTIALS
CC1020PS CC1060PS

1-1/8” 7/8”
7/8” 7/8”
5/16” 5/16” 1/8” 1/8”

CORNER GUARD

CC1030 CC1040 CG1515

Can be used for capping carpet, 1/8" resilient Cove Cap for use Flexible Vinyl Corner Guard: Corner
ceramic, or paneling up to when coving resilient floor or tile protector for walls and doorways
1 /4" thick. up to 3/16" thick. Peel and stick where a bumper guard is needed.
tape for easy application. This product will not shrink, crack or
CC1030PS chip like rigid plastics.
CC1040PS
ESSENTIALS

1-1/2”
13/16” 1/4” 7/8”
1/8”
1-1/2”

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)

11 Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only.
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
 SECTION 1
VINYL ACCESSORIES
VINYL FILLET STRIPS

FL3010 FL3016 FL3020

11/4" radius Flexible Cove 1 1/4" radius Flexible Cove 2" radius Flexible Cove Former.
Former. Used with carpet or Former. Similar to FL3010 but Used with carpet or resilient
resilient flooring to support self supporting. flooring to support cove area of
cove area of flooring material. flooring material. Provides a softer
*May also be ordered in curve than FL3010.
rigid PVC

FL3011
R 1-1/4” R 1-1/4” R 2”
1-7/16”
7/8” 7/8”

1/8”
2-1/2”
EXPANSION JOINT COVER

RD3000 1/2”
Resilient floor expansion joint cover prevents
cracking in floor covering due to expansion and
contraction of concrete. Ribbed section of the trim
is lined up over saw cut in the slab butting up to
floor covering. Use with VCT, Solid Vinyl, Rubber,
or Linoleum flooring

VCT

FLOOR EQUALIZERS V-Groove Glue lines Adhesive

Floor Covering

Unique "V-Groove" glue lines

provide greater surface
area for vastly improved
contact area.

PROFILE Y X Vinyl Reducer Strips (Floor Equalizer) with V-Groove technology..

NUMBER HEIGHT WIDTH Builds transition between floors up to 3/4" in height.
Finish coat of patch can be used in achieve perfect height.
RD9125 1/8” 11” Economical solution for height variances.
Quickly equalizes floor levels thereby minimizing the use of floor patch.
RD9250 1/4” 11” Saves time and labor. Custom length sizes available. Glued directly to substrate. Floor
covering can be adhered directly on top.
RD9375 3/8” 11”
Available only in Black.
RD9500 1/2” 11” Available only in 4ft. length

Available in all 36 colours

Available with special order only Available in all 18 ESSENTIALS colours Available in 4 colours (Beige, Black, Brown & Grey)
Available in 8 colours (Black, Brown, Beige, Grey, Charcoal, Medium Grey, Sable & Fawn) Available in Black only. 12
For colour availability please refer to Colour Guide/Legend on pg. 32 & 34
 SECTION 2
TAPDOWNS

CM1740 CM1741 CM1742 CM1750 CM1760

Residential weight Pinned Residential weight Pinned Residential weight Pinned Commercial Pinned Commercial duty Pinned
Tapdown for use with low to Tapdown with additional top Tapdown for use with low to Tapdown for use with high Tapdown for use with the
medium pile action backed return to lock in carpet. For medium pile action backed pile action backed carpet up thickest action backed
carpet up to 30 oz. use with low to medium pile carpet up to 30 oz. Ultra Pin to 60 oz. Ultra Pin system carpets. Ultra Pin system for
Ultra Pin system for maximum action backed carpet up to system for maximum holding for maximum holding maximum holding strength.
holding strength. 30 oz. Ultra Pin system for strength. 5/8” top face. strength. 7/8" top face.
Finishes: CVG, HDB, HTI, maximum holding strength. Finishes: HGA, HSI Finishes: CVG, HTI, HCA, Finishes: CVG, HTI, HCA,
HCA, HGA, HSI Finishes: HGA, HSI, HTI,HDB HGA, HSI, HDB HGA, HSI, HDB
SECTION
SECTION

5/8” 5/8” 3/4” 7/8”

5/8”

1-3/8” 1-3/8” 1-3/8” 1-1/2”

1-5/8”

CM1770 CONTOUR (FLEX)

Economy large lip (3/4") Tapdown THE FOLLOWING ITEMS ARE AVAILABLE IN
for use with the thickest action CONTOUR (FLEX) FOR CURVED AREAS:
backed carpet. May be used in
areas of low traffic. CM1770 has CM1741C CM1651C CM1760C
the same Ultra Pin system as our CM1650C CM1752C CM1653C
other pinned metals for maximum CM1751C CM1755C
holding strength. CM1655C
Finishes: CVG, HGA, HSI, HTI Customer Service
We have been focused on customer
service since the beginning. It is true
that we have the broadest assortment
of accessory products in the industry.
It is also true that we have a history
7/8” of order fulfillment that is recognized
as an industry leader. We are proud
of the fact that we bring new and
1-1/2” exciting products to market well in
advance of others, as well as
providing the basic products that are
used everyday. But our success is
really based on the exceptional
customer service provided by our
associates.

13
 SECTION 2
TAPDOWNS

CM1621 CM1650 CM1653 CM1657

Multi-purpose Tapdown that can be Commercial Pinless Tapdown for Residential weight Pinless Tapdown Commercial duty Pinless Tapdown
used for carpet underpad installation use with rubber backed and for use with foam backed carpet or for use in high traffic commercial
or glue down installations. The large lip direct glue down installations. direct glue down installations. settings. Used in glue down carpet
covers even the thickest carpets with Nail holes on 12" centres. Available in Peel & Stick. installations.
room for tucking the edge. Tackless can Finishes: HGA, HSI Finishes: CVG, HCA, HDB, HGA, Finishes: HGA, HSI
be used on the bottom for carpet with HSI, HTI
underpad installations.
Finishes: HGA, HSI, HTI

3/4” 7/8”
5/8” 5/8”

1-3/8” 1-1/4” 1-7/8”

1-5/16”

CM1666 CM1766 CM1680

Pinless Divider for commercial use. Pinned Divider for commercial use. Adjustable height multi-purpose (divider)
Used where foam backed carpet Used where canvas backed carpet moulding adapts to many
meets ceramic, hardwood, laminate, meets tile, hardwood, laminate or applications. Product can be tapped
cushion floor on plywood or sheet cushion floor on plywood. (Can be down to accommodate various
vinyl on subfloor. (Can be adjusted adjusted to accept slightly thinner thicknesses of different flooring
to accept slightly thinner materials). materials). For high traffic areas. materials.
For high traffic areas. Finishes: HGA, HSI, HTI, HCA Finishes: SGA, SCA
Finishes: HGA, HSI, HTI, HCA

1-1/8”
3/4” 3/4”

5/16” 7/16”
5/16”
1/4”

7/16” 1-3/8” 7/16” 1-11/16”

1-1/2”

14
 SECTION 2
JOINER BARS

CM1196 CM1197 CM2196 CM2197

1" Residential Bevel Bar for 1" Economy Bevel Bar for 1-1/2" Residential Bevel Bar for 1 -7/16" Economy Bevel Bar for
transitions. Made for height transitions. Made for height transitions. Made for height transitions. Made for height
differentials of up to 3/16". differentials of up to 3/16". differentials of differentials of up to 5/16".
Finishes: CVG, HDB, HGA, HSI, Light traffic only. up to 5/16". Light traffic only.
HTI, BCL Finishes: HCA, CVG, HGA, HSI, Finishes: HGA, HSI, HTI, BCL Finishes: CVG, HDB, HGA, HSI,
HDB, HTI HTI, HCA

1” 1” 1-1/2” 1-7/16”
SECTION

CM3196 CM1342 CM1344 CM1142

2" Commercial weight Bevel Bar. 3/4" Seam Binder Covers seams 1" Flat Joiner. For binding seams 1 -1/4" Flat Joiner. Wider than
For use in high traffic areas or of hard surface or resilient floors. at doorways where dissimilar CM1344 for seams where
where extreme height differentials Finishes: HGA, HSI, HTI floors of equal height meet. greater bridging is required.
exist. Finishes: CVG, HDB, HGA, HSI, Finishes: CVGM HGA, HSI, HTI,
Finishes: CVG, HGA, HSI, HTI, HTI, BCL, HCA HDB, HCA, BCL
BCL, HCA

1-1/4”
2” 3/4” 1”
1/10”
1/10” 1/10”

15
 SECTION 2
ALUMINUM NOSINGS

CM2184 CM2190 CM2191 CM2193

1-1/8" Drop Stair Nosing. 1-3/8” Drop Stair Nosing. 1-5/8" Drop Stair Nosing. 1-7/8" Drop Stair Nosing.
Protects edge of stair from Protects edge of stair from Protects edge of stair from Protects edge of stair from
damage. This product is damage. This product is damage. This product is damage. This product is
designed for residential or designed for residential or designed for light commercial designed for residential or
light commercial use. light commercial use. or residential use. light commercial use.
Finishes: CVG, HGA, HSI, HTI, Finishes: HGA, HSI, HTI, BCL, HDB Finishes: CVG, HCA, HDB, Finishes: CVG, HDB, HCA,
HDB HGA, HSI, HTI, BCL HGA, HSI, HTI, BCL

1-1/8”
1-1/8” 1-1/8” 1-1/8”

1-1/8”
1-3/8”
1-5/8” 1-7/8”

CM2199 CM2182 CM2194 CM2195

2" Drop Stair Nosing. Protects 1-1/8" Drop Economy Stair Full 2" Residential Drop Stair 1-1/2" Drop X 2-1/2" Tread
edge of stair from damage. Nosing. Protects edge of stair Nosing with 1-1/2" Top tread. Stair Nosing. Provides excellent
This product is designed for from damage. Covers most imperfections. The traction and protection at edge
light commercial or Finishes: CVG, HGA, HSI, HTI, wider top tread allows for nosing of stair. Ideal for repairing stairs
residential use. HDB to be secured away from stair where existing nosing has worn
Finishes: HGA, HSI, HTI, HDB edge especially when edges of out. Designed for commercial use.
stairs are damaged. Drilled staggered.
Finishes: HGA, HSI, HTI, HDB Finishes: CVG, HGA, HSI, BCL,
HTI, BDB

1-1/4” 1-1/8” 1-1/2” 2-1/2”

1-1/2”
1-1/8”
2” 2”

16
 SECTION 2
ALUMINUM NOSINGS

CM2198 CM2185 CM2192

1-3/16" Drop X 3-1/16" Tread Stair Nosing to Scribe for 1/8" VCT or 1-3/8" Drop Commercial Square
Nosing. Provides excellent traction and resilient floors of similar thicknesses. Nose for use on concrete pan or
protection at edge of stair. Ideal for 1 -5/8" inside drop to work in most square stairs. Can also be used
repairing stairs where existing nosing has settings. With adhesive reservoir for as a heavy duty corner guard.
worn out. Designed for commercial use. clean and easy installation. Drilling available by special order.
Drilled staggered. Finishes: SCA, SGA Finishes: SGA, MIL, BCL
Finishes: BCL, HGA

3-1/16” 1/8” 1-1/2”

SECTION

1-3/16”
1-3/8”
1-5/8”

CM1144 CM1146 & CM1148

2 1/2" Seambinder for use in 2 1/2" or 4" Seambinder for use in joining large gaps
joining large gaps or may be or may be used as threshold. Can also be used as an
used as threshold. Can also expansion joint cover. Drilled as per request.
be used as an expansion joint Finishes: MIL, SGA
cover. Drilled as per request.
Finishes: MIL, SGA

1/8”
3/16” 2-1/2”
CM1146
2-1/2” 1/8”
4”
CM1148

17
 SECTION 2
THRESHOLDS

WSB4424 WSB4425 WSB4426

Barrier Free quality extruded Aluminum Thresholds designed for use in commercial applications. Support bars built for added strength.
Full 1/2" height for retrofit situations.
See below for Low profile (LPB) Thresholds which are recommended for wheelchair accessible areas.
Construction Materials Board (CMB) listed material.

* Thresholds come drilled center line, staggered, or undrilled.

* Thresholds shown meet requirements of CAN/CSA-B651 and ADAAG-1992.
Finishes: MIL

1/8” 1/8” 1/8”

1/2” 1/2” 1/2”
6”
4” 5”

WSB4424LP WSB4425LP WSB4426LP

Barrier Free quality extruded Aluminum Thresholds designed for use in commercial applications. Support bars built for added strength.
1/4" height Low profile (LPB).
Thresholds recommended for wheelchair accessible areas.
Construction Materials Board (CMB) listed material.

* Thresholds come drilled center line, staggered, or undrilled,

* Thresholds shown meet requirements of CAN/CSA-B651 and ADAAG-1992.
Finishes: MIL

1/8” 1/8” 1/8”

1/4” 1/4” 1/4”
4” 5” 6”

18
 SECTION 2
ALUMINUM SPECIALTY TRIMS

CM330 CM1121 CM1124

1/10" J - Moulding for use with Tile Edge Cap for finishing the Sub Floor Reducer. This item is
materials up to 2.5mm (1/10") edge of tile or resilient floor. specifically designed to reduce
thick or for framing glass Accommodates materials from sub-floors up to 3/8"thick but
and mirrors. 0.080" up to 1/8" thick. can also be used for flooring
Finishes: BBR, BCL, SGA, SCA, Finishes: CVG, HGA, HSI materials such as laminate,
MIL, STI ceramic, and parquet.
Fastening holes are drilled on
sloped face. This allows
laminates to float freely and
eliminates the need to drill
3/4” through tough materials
SECTION

like ceramic.
13/16”
Finishes: HSI, HGA
1/10”
3/32”
1-1/4”

3/8”

CM1122 CM1125 CM3330 CM3340

Resilient Flooring Cap. Used when Resilient Flooring Cap. Used when Resilient flooring cove moulding Resilient flooring cove moulding
coving sheet goods up the wall to coving sheet goods up the wall to for use at the floor/wall for use at the floor/wall transition
finish off the exposed edge. For finish off the exposed edge. For transition to provide a coved to provide a coved finish.
materials up to 2.5mm (1/10") thick. materials up to 3.2mm (1/8") thick. finish. Can be sealed with Can be sealed with silicone to
Finishes: SCA, SGA, HGA, HSI, MIL Finishes: MIL, SCA, SGA silicone to offer excellent offer excellent resistance to dirt
resistance to dirt build up. build up. Accepts materials up to
Accepts materials up to 3.2mm (1/8”) thick
2.5mm (1/10”) thick Finishes: SGA, SCA, MIL
Finishes: MIL, SCA, SGA, STI

7/16”
7/16”
15/16” 5/16” 1/10” 1/8”

1/10” 1/8” 9/16” 9/16”

19
 SECTION 2
ALUMINUM SPECIALTY TRIMS

CM1155 CM1156 CM1157 CM1163

7/8" wide Hatch Cover Can be used between ceramic, Vinyl Hatch Cover: Can be used 3/4" X 3/4" Angle for use
moulding. Used to cover gaps hardwood and laminate floors between ceramic, hardwood and on corners to protect edge.
in the floor where hatch covers of equal heights. Where laminate floors of equal heights. Can also be used as an accent.
are installed. expansion is expected Where expansion is expected. Can be drilled. Also available:
Finishes: BBR, BCL, SCA, Finishes: SCA, SCP, SGA, Finishes: BGE, BLK, BRN, SGY 1162 (1/2” x 1/2”)
SGA, MIL, STI MIL, STI 1164 (1” x 1”)
Finishes: BBR, BCL, SCA, SGA,
MIL, STI

7/8” 7/8”
7/8” 3/4”

5/8” 5/16” 3/4”

3/4”

COCOMAT STRAIGHT EDGE Z-BAR

(CM3200) (CM3210) (CM3220)

Cocomat Edging to secure cocomat or 2-1/4" wide grooved Straight Edge. Grooves prevent Offset hearth metal for installing carpet
other floor coverings up to 3/4". tool from moving by biting into carpet. Allows carpet around fireplaces. Provides grip while
Jaws squeeze shut to trap material and technician to cut carpet up to 12 feet wide. remaining invisible.
double faced tape is used to fasten it Clear Anodized to prevent marking carpet. Finishes: MIL
to the floor. Finishes: SCL
Finishes: SCA, MIL SE 29” SE 75”
SE 36” SE 84”
SE 150”

1/2”

2-1/4”

20
 SECTION 3
WOOD GRAIN LAMINATES

LM4001 LM4002 LM4003 LM4005 LM4006

Floating Floor End Stop Expansion Joint (divider) for Floating Floor Reducer. Floating Floor Reducer. Reduces from laminate floor
Used when butting floating Floating Floors. Used when Reduces from 5/16" to 1/8" Reduces from 5/16" to to sub floor or to existing floor.
floors to walls, patio doors installing large areas of floating floor. Used when butting floating 0" floor. Used when butting Reduces from 9/16" to 0"
or other flooring materials floors as an expansion joint. floors up to 1/8" tile or resilient floating floors on top of Aluminum strength and
of similar heights such as Overhang allows expansion of sheet goods. existing floors or subfloor. durability. Woodgrain finish
hardwood or ceramic tile. floors and eliminates buckling. surface is treated with an
Should be used for any aluminum oxide finish.
installation greater than 12’ in Works with LM3003 (1/2")
any one direction. extended track woodgrain and
1” 1-1/2” satin finishes
7/16”
1/8” 1-5/8”
5/16” 1-1/2” 5/16”
(8mm) (8mm) 0”
5/16” 2”
5/16” (8mm)
(8mm)
0”
9/16”
(12mm)
SECTION

LM4004 LM3001 LM3002 LM3003 LM3004

Floating Floor Stairnosing. The easy to install LM3001 LM3002 track to be used LM3003 track to be used for LM3004 track to be used
Finishes edge of stair. snap-in track design, provides for stair nose applications. 10mm laminate floors. Track for 12.5mm laminate floors.
For nosing applications a unique sleek low profile to Flange adds strength and provides secure grip of Track provides secure grip
use LM3002. enhance any laminate floor. stability. Staggered drilled moulding for greater durability of moulding for greater
Made of rigid PVC. Made of rigid PVC. and safety. Flange adds extra durability and safety.
strength and stability. Flange adds extra strength
Made of PVC. and stability. Made of PVC.

1” 7/32” 7/32”
5/16” 7/32” 7/32”
8mm 8mm
(8mm)
1-3/16” 10mm 12.5mm
7/16” 1”
1” 1”

The mouldings are made of aluminum providing incomparable strength and durability. In addition the
wood grain surface is treated with an aluminum oxide finish that increases surface hardness up to 3 times
more over other sealers and coatings.

BEECH CHERRY MAPLE OAK RED OAK WALNUT

Wood Grain Finish Laminate
21 Mouldings available in OAK,
ROK, BCH, MAP, CHY, WAL
 SECTION 3
LAMINATE MOULDINGS
To Be Used With 8mm Flooring

LM1001 LM1002 LM1003 LM1004 LM1005

One piece Floating Floor End One piece Expansion Joint One piece Floating Floor One piece Floating Floor Stair One piece Expansion Joint
Stop (J-Mould) used when (divider) for Floating Floors. Reducer. Used when butting Nosing. Used when installing (divider) for Floating Floors.
butting floating floors to walls, Used when installing large floating floors up to 1/8" tile or floating floors on stairs. Can also Used when installing large areas
patio doors or other flooring areas of floating floors as resilient sheet goods. The large be used with ceramic tiles or of floating floors as an expansion
materials of similar heights such an expansion joint. Large overhang allows the laminate other floors of similar thickness. joint. Large overhangs allows
as hardwood or ceramic tile. overhangs allows expansion floor to expand and contract Finish: SCA, SGA, STI, SCP expansion of floors and
Finish: SCA, SGA, STI, SCP of floors and eliminates up to 1/2". eliminates buckling. Should be
buckling. Should be used for Finish: SCA, SGA, STI, SCP used for any installation greater
any installation greater than than 12' in any one direction.
12' in any one direction. Finish: SCA, SGA, STI, SCP
Finish: SCA, SGA, STI, SCP 1/2”

1/2” 1-1/2” 5/16” 1-1/16”

1” 5/16” 5/16”
5/16” 1/8” 5/16”
1-5/8”
1-3/16” 1-5/8” 1-1/8” 1-1/16”

To Be Used With 12.5mm Flooring

LM1251 LM1253 LM1254 LM1255

One piece Floating Floor End One piece Floating Floor One piece Floating Floor Stair One piece Expansion Joint
Stop (J-Mould) Used when Reducer. Used when butting nosing. Used when installing (divider) for Floating Floors.
butting floating floors to walls, floating floors up to 1/8" tile or floating floors on stairs. Used when installing large
patio doors or other flooring resilient sheet goods. The large Can also be used with areas of floating floors as an
materials of similar heights overhang allows the laminate ceramic tiles or other floors expansion joint. Large
such as hardwood or floor to expand and contract of similar thickness. Extended overhangs allows expansion
ceramic tile. up to 1/2" lower leg for better coverage. of floors and eliminates buckling.
Finish: SCA, SGA, STI, SCP Finish: SCA, SGA, STI, SCP. Finish: SCA, SGA, STI, SCP Should be used for any
installation greater than 12'
in any one direction.
9/16” 1-1/2” 1/2” Finish: SCA, SGA, STI, SCP

1-1/8”
1/2”
1/2” 1/8” 1/2”
1/2”
1-5/8”
1-3/16” 1-1/8”
1-1/16”

22
 SECTION 3
MDF WOODGRAIN MOULDINGS
To be used with 6mm-9mm laminate/floating floors.

LM7001 LM7002 LM7003 LM7004

Finishes edge between laminate Finishes gap between level Finishes edge between Finishes edge of laminate/wood
floor and carpet, fireplace hearths flooring areas. laminate/wood flooring and flooring at stairs.
and at exterior doorways. other hard surface or carpet.
Finishes edge at outside doors.

1-3/8” 1-3/4” 1-3/4” 2-1/8”

LM7010 LM7020 LM7030

SECTION

Quarter round finishes space Accessory piece available to Accessory piece available to
between laminate/wood accommodate floors up to accommodate floors up to
flooring and wall base. 15mm thick, when used with 15mm thick, when used with
LM7030. LM7020.

11.5 mm 4 mm
13.5
3/4” mm

*LM7050: Wall Base Available (Special Order Only)

COLOUR GUIDE/LEGEND (6mm-9mm)

220 224 232 238 240 248

256 258 264 300 304 310

456 474 476 492 504 506

23 524 630 640 762 786 796

 SECTION 3
MDF WOODGRAIN/CORK MOULDINGS
To be used with 12mm-14mm laminate/floating floors.

LM7101 LM7102 LM7103 LM7004

Finishes edge between laminate Finishes gap between level Finishes edge between Finishes edge of laminate/wood
floor and carpet, fireplace hearths flooring areas. laminate/wood flooring and flooring at stairs.
and at exterior doorways. other hard surface or carpet.
Finishes edge at outside doors.

2” 2” 2-3/8” 2-1/8”

LAMINATE COLOUR GUIDE/LEGEND NEW

NEW

238 240 248 300 304 310

492 504 506 762 220 224

LM7201 LM7202 LM7203 LM7204

Finishes edge between laminate Finishes gap between level Finishes edge between Finishes edge of laminate/wood
floor and carpet, fireplace hearths flooring areas. laminate/wood flooring and flooring at stairs.
and at exterior doorways. other hard surface or carpet.
Finishes edge at outside doors.

2” 2” 2-3/8” 3-1/4”

CORK CO
COLOUR
LOUR GUIDE/LEGEN
GUIDE/LEGENDD NEW
N
NE
EEW
W

110 114 122 124 126 132

24
 SECTION 4
TILE EDGE

SOLID BRASS CM2148

3/16" (4mm) Flat Tile Edge for use with 4mm CM2150
tile. Pre-punched for easy setting into adhesive.
Protects tile from damage while providing a
finished butting edge for other flooring materials. 5/16” (8mm) Flat Tile Edge for
Finishes: MIL, SCA use with 8mm tile. Pre-punched for
easy setting into adhesive. Protects
tile from damage while providing
SOLID BRASS 3/16” (4mm) a finished butting edge for other
flooring materials.
1/4'(6mm), 5/16'(8mm), 3/8"(10mm), Finishes: BBR, SCA, SDB, MIL,
1/2"(12.5mm) Solid Brass Tile Edge for use with SBK, STI, WHT
ceramic tiles. Pre-punched for easy setting into
adhesive. Protects edge of tile from damage
while providing a clean button edge Solid brass
is excellent for areas where high mechanical 5/16” (8mm)
stress and chemical usage occurs.
Also available in Stainless Steel
CM2149
1/4” 5/16”
(6mm) (8mm) 1/4" (6mm) Flat Tile Edge for use with 6mm tile.
Pre-punched for easy setting into adhesive.
CM2139 CM2140 Protects tile from damage while providing a
finished butting edge for other flooring materials.
Finishes: BBR, BCL, SCA, SCP, SDB, SGA, MIL,
3/8” SBK, STI, WHT
(10mm) 1/2” (12.5mm)
1/4” (6mm)
CM2141 CM2142
SECTION

CM2151 CM2152 CM2154 CM2155

3/8" (10mm) Flat Tile Edge for 1/2" (12.5mm) Flat Tile Edge for 5/8" (16mm) Flat Tile Edge for 3/4" (20mm) Flat Tile Edge for
use with 10mm tile. Pre-punched use with 12.5mm tile. use with 16mm tile. Pre-punched use with 20mm tile. Pre-punched
for easy setting into adhesive. Pre-punched for easy setting into for easy setting into adhesive. for easy setting into adhesive.
Protects tile from damage while adhesive. Protects tile from Protects tile from damage while Protects tile from damage while
providing a finished butting edge damage while providing a providing a finished butting edge providing a finished butting edge
for other flooring materials. finished butting edge for other for other flooring materials. for other flooring materials.
Finishes: BBR, SCA, SCP, SDB, flooring materials. Finishes: BBR, BCL, SCA, SGA, Finishes: BBR, BCL, SCA, SGA,
SGA, MIL, SBK, STI, WHT Finishes: BBR, BCL, SCA, SCP, SBK, STI, SCP SBK, STI, SCP
SDB, SGA, MIL, SBK, STI, WHT

3/4” (20mm)
3/8” (10mm) 5/8” (16mm)
1/2” (12.5mm)

25
 SECTION 4
TILE EDGE

CM2249 CM2250 CM2251 CM2252

1/4" Tile Corner Edge for use 5/16" Tile Corner Edge for use 3/8" Tile Corner Edge for use 1/2” Tile Corner Edge for use
with 1/4" tile. Pre-punched for with 5/16" tile. Pre-punched for with 10mm tile. Pre-punched for with 12.5mm tile. Pre-punched
easy setting into adhesive. easy setting into adhesive. easy setting into adhesive. for easy setting into adhesive.
Protects edge of tile from Protects edge of tile from Protects edge of tile from Protects edge of tile from
chipping. Provides a 90 chipping. Provides a 90 chipping. Provides a 90 chipping. Provides a 90
degree corner. Can also be degree corner. Can also be degree corner. Can also be degree corner. Can also be
used on corners. used on corners. used on corners. used on corners.
Finishes: BBR, BCL, SBK, SCA, Finishes: BBR, BCL, SBK, SCA, Finishes: BBR, BCL, SBK, SCA, Finishes: BBR, BCL, SBK, SLA,
SCP, SGA, SDB, MIL, STI MIL, STI, SDB SCP, SGA, MIL, STI, SDB SCP, SGA, STI

1/4” (6mm) 5/16” (8mm) 3/8” (10mm) 1/2” (12.5mm)

CONTOUR FLEXMAX CM2130 CM2135 CM2136

All of our Flat Tile Edge can be 1/4" J-Moulding for use with 1/4" 3/8" J-Moulding for use with 3/8" 1/2" J-Moulding for use with
ordered in a contour (flex) style. flooring materials or for framing glass tile. Can also be used to frame 1/2" tile. Can also be used to
The setting flange has an extra and mirrors. Also used for capping glass, mirrors, or wood panels. trim wood panels.
cut that allows trim to be bent 1/4" ceramic tile around bath tubs. Finishes: BBR, BCL, SCA, SGA, SCP, Finishes: BBR, BCL, SCA, SGA,
and shaped around curved floor Finishes: BBR, BCL, SCA, SGA, MIL, STI MIL, STI
applications. MIL, STI

Available for
CM2148, CM2149,
CM2150, CM2151,
CM2152, CM2154, 1/4”
CM2160, CM2161, 3/8” 1/2”
(6mm)
CM2162 (10mm) (12.5mm)

3/4” 1”
3/4”

26
 SECTION 4
ADAPTERS AND REDUCERS

CM2160 CM2161 CM2162

5/16" ceramic to carpet 3/8" ceramic to carpet 1/2" ceramic to carpet adapters
adapters for use where (5/16") adapters for use where (3/8") for use where (1/2") 12.5mm Sloped face creates a smooth
8mm tile meets low pile carpet 10mm tile meets low pile carpet tile meets low pile carpet or transition between tile and
or other 1/4" flooring. or other 1/4" flooring. other 1/4" flooring. adjacent floor coverings.
Finishes: BBR, BCL, SCA, SCP, Finishes: BBR, BCL, SCA, SCP, Finishes: BBR, BCL, SCA, SCP, The moulding has a 1/4"
SGA, MIL, SBK, STI, SDB SGA, MIL, SBK, STI, SDB SGA, MIL, SBK, STI, SRB
opening to allow adjacent
flooring edge to be inserted and
protected. The vertical leg
1/2” (12.5mm) provides protection to the edge of
5/16” (8mm) 3/8” (10mm) the ceramic tile. This moulding
features an extended base which
1/4” resists lifting of ceramic when
1/4” 1/4”
downward pressure is applied
to the face. Pre-punched for easy
setting into adhesive.
SECTION

CM2170 CM2171 CM2172

5/16" Tile Reducer for use with 3/8" Tile Reducer for use with 1/2" Tile Reducer for use with
(5/16") 8mm tile. The moulding (3/8") 8mm tile. The moulding (1/2") 12.5mm ceramic tile.
has a sloped face to create a has a sloped face to create a The moulding has a sloped face
smooth transition between smooth transition between (3/8") to create a smooth transition
(5/16") 8mm tile and (1/8") 8mm tile and (1/8") 3.2mm between (1/2") 12.5mm
3.2mm adjacent surface adjacent surface such as resilient tile and (1/8") 3.2mm adjacent Moulding has a sloped face to
such as resilient tile or sheet tile or sheet goods. Pre-punched surface such as resilient tile or
goods. Pre-punched for easy for easy setting into adhesive. sheet goods. Pre-punched for create a smooth transition
setting into adhesive. easy setting into adhesive. between tile and (1/8") 3.2mm
Finishes: BBR, BCL, SCA, SCP,
Finishes: BBR, BCL, SCA, SCP, SDB, SGA, MIL, SBK, STI Finishes: BBR, BCL, SCA, SCP, adjacent surface such as resilient
SDB, SGA, MIL, SBK, STI SDB, SGA, MIL, SBK, STI tile or sheet goods. Pre-punched
for easy setting into adhesive.

1/8” 1/8” 1/8” 1/2”

5/16” 3/8”
(10mm) (12.5mm)
(8mm)

27
 SECTION 4
NOSINGS AND EXPANSION JOINTS

CM4050
CM4051
CM4052 CM4251 CM4151

5/16” (8mm), 3/8” (10mm) Ceramic Tile Stair Nosing. This product provides CM4251 3/8” (10mm) Ceramic Tile 3/8” (10mm)- 1/2” (12.5mm) Dual
increased strength and rigidity to stair while also serving to protect edge of tile. Stair Nosing. This product provides purposes Decorative Edging used for
Long 1- 5/8” inside drop covers nose of standard stairs and gives a smooth, increased strength and rigidity to stair counter tops, raised platforms, and
clean appearance. May be used in light commercial or residential applications. while also serving to protect edge of stairs. Can be used for both 10mm
Product comes in 6’ or 12’ lengths and is punched to accept adhesives. tile. Long 2” inside drop cover nose of and 12.5mm tile.
Finishes: HBC, HBB, HCP, HTI non standard stairs and gives a Finishes: BBR, SBK, SCA, SGA, STI
smooth, clean appearance. May be
used in light commercial or residential
applications. Product comes in 6’ or
12’ lengths and is punched to accept
adhesives.
Finishes: HBC, HBB, HCP, HTI, HGA,
HBK, HCA

5/16” (8mm) 3/8” (10mm) 3/8” (10mm)

1/2” (12.5mm)

3/8” (10mm)
1-5/8” 1-5/8” 1/2” (12.5mm)
1-5/8”

2”
CM4050 CM4051 CM4052

CM4071 CM3060
CM4072 CM3051 CM3071

CM4071 h3/8” (10mm) 3/8” (10mm) Heavy Duty Expansion CM3060 5/16” (h) (8mm)
FPCM4071 V-Replacement Vinyl Insert. Joint for placement over control and CM3071 3/8” (h) (10mm)
CM4072 h1/2” (12mm) cold joints. Expansion joints are a Surface Expansion Joint is coextruded
FPCM4072 V-Replacement Vinyl Insert. prerequisite in ceramic tile, natural from rigid and soft PVC. Use in tiled
Anti Skid Stair Nosing for stairways stone, and terrazzo installations. floor applications where flexibility in
with high traffic, or where wet conditions Made in Solid Brass, Stainless Steel stress is needed. PVC is resistant to
exist. An anti skid vinyl insert is placed or Aluminum weather and UV rays. Resistant to
unto aluminum base to form a sturdy and most household cleaning products.
long lasting stair nose. Finishes: Grey
Finishes: BGE, BLK, BRN, GRY
1/2”
1-1/8” 5/16”
3/8” (10mm)
h”
h”
7/8” 7/8”
5/8” 5/8”

28
 SECTION 4
RIGID VINYL TILE EDGE
J -CAP

3/16" (4mm) 1/4" (6mm) 3/8" (10mm)1/2" (12.5mm) Tile Edge

CT1034 for use around bathtubs, windows, back splashes, etc. Can also be
CT1036 used to eliminate mitering of tiles at corners such as walk up tubs.
CT1039 Pre-punched for easy setting into mortar.
CT1085 Finishes: BLK, BON, GRY, WHT, TAN, BGE
Other colours available with minimum order quantity.

1/2”
3/16” 1/4” 3/8”
(12.5mm)
(4mm) (6mm) (10mm)

3/4” 7/8” 7/8” 7/8”

CT1034 CT1036 CT1039 CT1085

CT1024 CT1025 CT1026

3/16" (4mm) 1/4 " (6mm) 3/8"
(10mm) J-Cap used as a tile edge
around bath tubs, windows, back
splashes etc.
1/4" (6mm), 5/16"(8mm) & 3/8" (10mm) Heavy duty vinyl tile
edge for use around bath tubs, windows, back splashes, etc.
Finishes: WHT, BON
CT1076 Heavy profile allows this product to be used on floor tile where
CT1078 thinner products may not stand up to the traffic. Pre-punched for
easy setting into mortar
CT1080 3/16”
Finishes: SBK, BON, GRY, WHT, TAN, BGE (4mm)

3/8” 5/8”
5/16”
1/4” (10mm)
(8mm) CT1024
(6mm)
SECTION

7/8” 7/8” 7/8”

1/4”
(6mm)
CT1076 CT1078 CT1080
4

3/4”
CT1025

3/8”
(10mm)

5/16"(8mm) & 3/8" (10mm) Heavy duty vinyl tile edge for use
around bath tubs, windows, back splashes, etc. Heavy profile allows
this product to be used on floor tile where thinner products may not
3/4”
CT1058 stand up to the traffic. Pre-punched for easy setting into mortar
CT1060 Finishes: SBK, BON, GRY, WHT, TAN, BGE CT1026

5/16” 3/8”
(8mm) (10mm)

7/8” 7/8”

CT1058 CT1060

29
 SECTION 4

Mortar Polypropylene Mortar ProVa-Flex is a polypropylene membrane sandwiched ProVa-Flex uncouples the floor covering from the
Membrane
between a white polypropylene non woven fabric substrate and prevents the transfer of stresses to
on the underside to maximize bonding to the subfloor. the tiled surface. Thus, a crack caused by
It also has an interwoven polypropylene netting movement in the substrate is neutralized.
material adhered to the top surface to provide Cracks in the substrate are bridged and not
mechanical bonding properties as well as transferred to the floor covering.
enhancing the surface of contact with mortars used.
ProVa-Flex is approximately 3mm high.
ProVa-Flex distinctive red colour creates a useful
contrasting background for installers to ensure full
adhesive coverage.

Interwoven Non Available in: 3.28ft x 82ft (269 sq. ft)

Tile Netting Woven Substrate
Material Material

Tile Underlay Protegga is a multi functional polypropylene membrane developed as an underlay for ceramic tiles
Dovetail cut and natural stone. It acts as an "uncoupling" membrane on all suitable substrates and as a water
Anchoring vapour pressure equalization membrane against dampness in the substrate.
Tile Adhesive
Fibre Fabric
Cavity Grout
Sheet Thickness: nominal 0.50mm Water Vapour Resistance: 1500m2.s.GPa/kg or
Stud Height: approx. 3mm 280m equivalent air layer
Unit Weight: 0.51kg/m2 Air gap Volume: 1.3 liter/m2
Working Temperature: -10° to 60°C Stud Filling Volume: 1.6 liter/m2 tile adhesive
Installation Temperature: +10° to 40°C Life Expectancy: 50 years
Storage Temperature: max. 45°C Colour: Red
Softening Temperature: +160°C
Vapour
Adhesive Concrete Stress Available in: 3.28ft x 82ft (269 sq. ft)
Channel

ProVa-Lay provides all the labor-saving benefits of standard plastic roll uncoupling products such as being
lightweight, and quick and easy to install - and it offers the same crack isolation protection. Unlike other
underlayments, however, the innovative reinforced mesh panel design of ProVa-Lay enables it to add supprt
to wood substrates and in doing so, greatly reduces deflection. Prova-Lay actually replaces the need for a
second layer of plywood in many installations. In addition, ProVa-Lay provides greater compression and tensile
strength than traditional plastic roll products.

Benefits Compared to Standard Roll Uncoupling Products

• Reduces deflection in wood substrates
• Stone Installations - increases substrate support
• Large format tile - provides flatter plane and stiffer substrates
• Only 1/8”
• Suitable for tiles 2” x 2” and smaller
• Weighs only 1.06 lbs. per panel (6.5 sq. ft)
• Latex modified thinset recommended for porcelain tile installation

Available in: 30 panels/carton (195 sq. ft) 1 panel: 2ft x 3.2ft

FLEXIBLE - Crack bridging - decoupling

PROTECTS - Against Mold and Mildew
FAST SEALING - No wait time to install NEW surface
WATERPROOF - Anti-Fracture Membrane

Use as a waterproof membrane in wet areas such as: Material: Polyethylene

Colour: Red
• Showers Thickness: 0.4mm
• Laundry Rooms Width: 1 metre
• Bathrooms
• Countertops

Available in 5 sq.m/10 sq.m/25 sq.m 30

 SECTION 5
SOLID OAK TRIM

FW6800 ** FW6810 ** FW6820 * FW6830 *

Reducer Moulding for reducing Reducer Moulding for reducing Overlap Tile Edge. For use with Binder Bar or Equalizer.
3/8" flooring materials such 7/16" flooring materials such resilient floors or tile up to 1/8" Joins adjacent floors height
as ceramic or hardwood. as ceramic or hardwood. differentials up to 3/16".
Gives smooth transition from Gives smooth transition from
lower to higher floors. lower to higher floors.
1/8”

3/8”
13/16”
7/16”
15/16” 3/16”
1-3/4” 1-1/2”

FW6840 * FW6860 * FW6870 * FW6880 ** FW6890 **

Binder Bar or Equalizer. Joins Seambinder for joining Seambinder for joining Reducer Moulding for Seambinder for joining
Adjacent floors with height adjacent floors of equal adjacent floors of equal reducing 3/4" flooring adjacent floors of equal
differentials up to 3/8” height 1 - 3/4" wide. height. 2 1/2” wide. materials such as ceramic height 1 -1/2" wide.
or hardwood. Gives
smooth transition from
3/8” lower to higher floors. 1-1/2”
1-3/4” 0.190”
9/16” 3/8”
3/8” 3/8”
2” 2-1/2”
7/16”
1/4”
SECTION

3/4”
2-1/2”
5

All items come in 6 ft. length.

All mouldings are Solid Oak.
* Items are supplied pre-drilled with a sanded but unfinished surface
** Items supplied undrilled

The wood in these products come from well managed forests independently certified in
31 accordance with the rules of the Forest Stewardship Council
 180

BENGARD
CC1010.............................11 CM1770............................13 CT1080........................29 NT4220.....................9
CC1010PS.........................11 CM2130............................26 CT1085........................29 NT4230.....................9
CC1020.............................11 CM2135............................26 CX400............................3 NT4320.....................9
CC1020PS.........................11 CM2136............................26 CX1000..........................5 NT4330.....................9
CC1030............................11 CM2139............................25 CX1100..........................5
CC1030PS.........................11 CM2140............................25 Protegga....................30
CC1040............................11 CM2141............................25 EB450............................4 Prova - Flex.................30
CC1040PS.........................11 CM2142............................25 Prova - Mat................30
CC1060............................11 CM2148............................25 FL3010.........................12 Prova - Lay.................30
CC1060PS..........................11 CM2149............................25 FL3011.........................12
CG1515............................11 CM2150............................25 FL3016.........................12 QR6875.....................4
CM1110..............................6 CM2151............................25 FL3020.........................12
CM1111..............................6 CM2152............................25 FPCM4071....................28 RD2010......................8
CM1120..............................6 CM2154............................25 FPCM4072....................28 RD2020......................8
CM1121 (Vinyl).....................6 CM2155............................25 FW6800......................31 RD2030......................8
CM1121 (Aluminum)............19 CM2160............................27 FW6810......................31 RD2040......................8
CM1122............................19 CM2161............................27 FW6820......................31 RD2130......................8
CM1124............................19 CM2162............................27 FW6830......................31 RD2147......................8
CM1125 (Vinyl).....................6 CM2170............................27 FW6840......................31 RD2148......................8
CM1125 (Aluminum)............19 CM2171............................27 FW6860......................31 RD2150......................8
CM1126..............................7 CM2172............................27 FW6870......................31 RD2151......................8
CM1130..............................5 CM2182............................16 FW6880......................31 RD2320.....................7
CM1140..............................5 CM2184............................16 FW6890......................31 RD2330.....................7
CM1142............................15 CM2185............................17 RD2400.....................7
CM1144............................17 CM2190............................16 LM1001.......................22 RD3000...................12
CM1146............................17 CM2191............................16 LM1002.......................22 RD9125....................12
CM1148............................17 CM2192............................17 LM1003.......................22 RD9250....................12
CM1150..............................6 CM2193............................16 LM1004.......................22 RD9375....................12
CM1151..............................6 CM2194............................16 LM1005.......................22 RD9500....................12
CM1155............................20 CM2195............................16 LM1251.......................22 RDV149......................8
CM1156............................20 CM2196............................15 LM1253.......................22 RR250........................3
CM1157............................20 CM2197............................15 LM1254.......................22 RR400........................3
CM1161 (Vinyl).....................6 CM2198............................17 LM1255.......................22 RR600........................3
CM1162............................20 CM2199............................16 LM3001.......................21 RV250........................3
CM1163............................20 CM2249............................26 LM3002.......................21 RV400........................3
CM1165..............................6 CM2250............................26 LM3003.......................21 RV600........................3
CM1171..............................6 CM2251............................26 LM3004.......................21
CM1181..............................7 CM2252............................26 LM4001.......................21 ST5010....................10
CM1196............................15 CM330.............................19 LM4002.......................21 ST5010SA................10
CM1197............................15 CM3051............................28 LM4003.......................21 ST5010DA................10
CM1200..............................7 CM3060............................28 LM4004.......................21 ST5030....................10
CM1342............................15 CM3071............................28 LM4005.......................21 ST5031....................10
CM1344............................15 CM3196............................15 LM4006.......................21 ST5030SA................10
CM1621............................14 CM3330............................19 LM7001.......................23 SR5080....................10
CM1650............................14 CM3340............................19 LM7002.......................23 SOLID BRASS.............25
CM1651..............................5 CM4050............................28 LM7003.......................23 STRAIGHT EDGE.........20
CM1651P............................5 CM4051............................28 LM7004.......................23 (CM3210)
CM1653............................14 CM4052............................28 LM7004.......................24
CM1655..............................5 CM4071............................28 LM7010.......................23 TR250.........................3
CM1655P............................5 CM4072............................28 LM7020.......................23 TR400.........................3
CM1657............................14 CM4151............................28 LM7030.......................23 TR600.........................3
CM1658..............................5 CM4251............................28 LM7101.......................24 TX250.........................3
CM1659..............................5 COCOMAT (CM3200).........20 LM7102.......................24 TX400.........................3
CM1660..............................5 CONTOUR (FLEX)..................13 LM7103.......................24 TX600.........................3
CM1666............................14 CONTOUR FLEXMAX.............26 LM7201.......................24
CM1680............................14 CR2050PS..........................11 LM7202.......................24 VX250.........................3
CM1740............................13 CT1024.............................29 LM7203.......................24 VX400.........................3
CM1741............................13 CT1025.............................29 LM7204.......................24 VX600.........................3
CM1742............................13 CT1026.............................29 NS4010.........................9
CM1750............................13 CT1034.............................29 NS4020.........................9 WSB4424.................18
CM1751..............................5 CT1036.............................29 NS4023.........................9 WSB4425.................18
CM1752..............................5 CT1039.............................29 NS4024.........................9 WSB4426.................18
CM1755..............................5 CT1058.............................29 NS4030.........................9 WSB4424LP...............18
CM1759..............................5 CT1060.............................29 NS4120.........................9 WSB4425LP...............18
CM1760............................13 CT1076.............................29 NS4310.........................9 WSB4426LP...............18
CM1766............................14 CT1078.............................29 NS4700.........................9
Z-BAR (CM3220)........20

32
 180

BENGARD
Notes
...................................................................................
...................................................................................
...................................................................................
...................................................................................
...................................................................................
...................................................................................
...................................................................................
...................................................................................

Drawings

33
 180

BENGARD
Available in all 36 colours

ST050-White ST022-Pearl ST034-Putty ST003-Shell White ST024-Antique White ST006-Light Beige

ST049-Beige ST095-Sandlewood ST080-Fawn ST009-Grey Beige ST045-Sand ST150-Landscape

ST042 -Sable ST059-Heather Green ST090-Steel Blue ST130-Sisal ST041-Ocean Breeze ST031-Dark Forest

ST085-Burgundy ST047-Brown ST055-Silver Grey ST086-Hunter Green ST058-Windsor Blue ST005-True Blue

ST038-Pewter ST028-Medium Grey ST048-Grey ST030-Ink Spot ST014-Tropical Rain ST053 -Mauve

ST020-Charcoal ST063-Burnt Umber ST040 -Black ST060-Taupe ST007-Cranberry ST021-Platinum Grey

Colours may not be exactly as shown

ALUMINUM FINISHES
BBR BRIGHT BRASS HBC HAMMERED BRIGHT CLEAR HSI HAMMERED SILVER SCL SATIN CLEAR
BCL BRIGHT CLEAR HCP HAMMERED CHAMPAGNE HTI HAMMERED TITANIUM SCP SATIN CHAMPAGNE
BRS BRASS HCA HAMMERED CLEAR ANODIZED MIL MILL FINISH SDB SATIN DARK BRONZE
CVG COVENTRY GOLD HDB HAMMERED DARK BRONZE SBK SATIN BLACK SGA SATIN GOLD ANODIZED
HBB HAMMERED BRIGHT BRASS HGA HAMMERED GOLD ANODIZED SCA SATIN CLEAR ANODIZED STI SATIN TITANIUM
 For continuous updates check our website
for the latest innovations

www.loxcreenflooring.com

5720 Ambler Drive

Mississauga, Ontario
L4W 2B1
Tel: (905) 625-3210 Fax: (905) 625-3396
(800) 565-6653

TORONTO • DALTON • LOS ANGELES