DULUX AURA HIGH GLOSS
R2100128 LINE (SOLVENTBASED)
PRODUCT INFORMATION
PRODUCT NAME Dulux Aura High Gloss
Product Code R2100128 LINE
DESCRIPTION Dulux Aura High Gloss is a premium solvent based high gloss finish that
gives a smooth mirror-like finish.
USAGE Suitable for use on all types of interior and exterior wood and metal
surfaces.
BENEFITS High gloss and excellent gloss retention.
Good brush loading and good sag resistance.
Excellent colour fastness.
No added Lead and Mercury
Excellent durability and fungus resistance.
Certified with Malaysian Standards MS 125:1995
PACK SIZE 1 and 5 litres
COLOUR RANGE Refer to Aura colour catalogue
PERFORMANCE GUIDE
FILM PROPERTIES Resistant to mild chemical fume attack but where there is heavy attack, e.g.
Chemical Resistance actual contact with chemicals, specialist paint systems will be required.
Generally resistant to heat up to 90C, but some discolouration of light
Water Resistance colours may occur at temperatures above 80C.
Resistant to the levels of atmospheric humidity present in normal interior
and exterior environments. Not suitable for use on immersed surfaces.
THEORECTICAL COVERAGE A guide to the theoretical coverage which can be achieved under normal
conditions is 16-18 m2/L.
PRODUCT DATA
COMPOSITION Pigment : Lightfast Non-Lead Pigments.
(nominal) Binder : Alkyd.
Solvent : White Spirit.
VOLUME SOLIDS White 50% (nominal), other colours will vary.
FLASH POINT 35-40C
APPLICATION
THINNING
Brush or Roller Thinning is usually not necessary after thorough stirring. If required, dilute
the paint up to 10% with white spirit.
Conventional Spray Dilute with 10%-20% of white spirit.
Airless Spray Ready for use.
SPRAY RECOMMENDATIONS
Conventional spray Satisfactory through most equipment.
Airless Spray A typical set up for airless spray application is a minimum working pressure
on paint of 140 kg/cm2 (2000 lb/sq in) with a spray tip size 0.38mm (15
thou) and a spray tip angle 65.
DRYING TIME
Single coat at standard thickness: 30 -40 microns
Touch Dry 2-4 hours.
Recoat 6-8 hours.
Drying time is dependent on many factors such as the environment,
temperature, humidity, number and thickness of coats applied, thinner used
and substrate condition.
CLEANING UP Clean all equipment with white spirit immediately after use.
PRE-APPLICATION
SURFACE PREPARATION Surfaces must be clean, dry, free from all defective or poorly adhering
material, dirt, grease, wax etc. Previously painted surfaces should be
thoroughly rubbed down using a suitable abrasive paper and then dusted off.
Any scrapped area should be spot primed. Light sanding on surface would
ensure better subsequent intercoat adhesion.
Ferrous surfaces should be sanded or wire-brushed to remove millscale and
rust. Remove the rust thoroughly and the area should be spot- primed.
For optimum performance, new galvanized and aluminium surfaces should be
cleaned and degreased, then pre-treated with an appropriate pre-treatment
primer to ensure good adhesion.
SYSTEM INFORMATION PRIMER (1 COAT) UNDERCOAT (1 COAT) FINISH (2-3 COATS)
Wood Dulux Aluminium
Wood-Primer Sealer
(A517-3697) Dulux Aura Wood & Metal Dulux Aura High
Metal Dulux Aura Metal Undercoat Gloss (R2100128
Primer (A545-101) LINE)
(A500-388)
PRECAUTION
HEALTH, SAFETY AND Product safety data sheet available upon request
ENVIRONMENT INFORMATION
Any advice, recommendations, information, assistance or service provided by Akzo Nobel Paints in relation to goods manufactured or
marketed by it or their use or any application is given in good faith. However, any advice, recommendations, information, assistance or service
provided by Akzo Nobel Paints is provided without expressed or implied warranties.
Date: Jan 2020
Akzo Nobel Paints (Malaysia) Sdn Bhd
(Formerly known as ICI Paints (Malaysia) Sdn Bhd)
For further details on Product Data Sheet, kindly contact:
Customer Care Department
Tel: 1-800-88-9338 Website: www.dulux.com.my Email:
[email protected]
