2-Storey Minglanilla Analysis
Uploaded by
imweljohncovero152-Storey Minglanilla Analysis
Uploaded by
imweljohncovero15STRUCTURAL ANALYSIS
AND DESIGN CALCULATIONS
Project: PROPOSED TWO-STOREY RESIDENTIAL
BUILDING
Location: Velpal Phase 2, Blk 2, Lot 1, Pakigne, Minglanilla
Owner: Gladdes Salatan Spannbauer
Civil/Structural Engineer:
Engr. Jayward T. Laput, CE, RMP
PRC No. 138139 PTR No. 2754424
Date: 05-16-2015 Date: 01-08-2025
TIN No. 322-467-389 Place: CEBU CITY
3D VIEW OF THE BUILDING STRUCTURE
VIEW 1
VIEW 2
DESIGN CRITERIA
Project: PROPOSED TWO-STOREY RESIDENTIAL BUILDING
Location: Velpal Phase 2, Blk 2, Lot 1, Pakigne, Minglanilla
Owner: Gladdes Salatan Spannbauer
1. DESIGN CODE AND REFERENCES
National Structural Code of the Philippines (NSCP) Volume 1, Seventh Edition 2015
for Buildings, Towers and Other Vertical Structures
ASEP Steel Handbook (2004 Edition)
Design of Concrete Structures 13th Edition by Nilson, Darwin & Dolan
Steel Structures (Design and Behaviour Emphasizing LRFD) by Salmon, Johnson &
Malhas
2. OCCUPANCY CATEGORY (Table 103-1, NSCP 2015)
IV (Standard Occupancy Structures)
3. DESIGN LOADS
DEAD LOADS (Section 204, NSCP 2015)
i. Selfweight of the Structure:
1. Concrete Unit Weight 23.5 kN/m3
2. Steel Unit Weight 77.0 kN/m3
ii. Floor Topping & Finishes 1.20 kPa
iii. Ceiling 0.20 kPa
iv. Interior Partition Walls 1.2 kPa
v. Exterior Partition Walls 10 kN/m
vi. Roofing 0.20 kPa
vii. Mechanical / Electrical Utilities 0.20 kPa
viii. Others 0.10 kPa
LIVE LOADS (Section 205, NSCP 2015)
i. Residential 1.90 kPa
EARTHQUAKE LOADS (Section 208, NSCP 2015)
i. Seismic Zone Factor, Z (NSCP Table 208-3) 0.40
ii. Distance from Seismic Source (Approx.) 5 km
iii. Seismic Source Type (NSCP Table 208-4) A
iv. Importance Factor, I (NSCP Table 208-1) 1.0
v. Ductility/Resistance Factor, R (NSCP Table 208-11) 8.5
vi. Soil Profile Type, S (NSCP Table 208-2) Sd
vii. Near Source Factor, Na (NSCP Table 208-5) 1.2
viii. Near Source Factor, Nv (NSCP Table 208-6) 1.2
ix. Static Analysis (NSCP Section 208.5.2)
ೡ ூ ଶ.ହೌ ூ
ܸ= ܹ, ܸ ≤ ܹ, ܸ > 0.11ܥ IW (NSCP Eq’s 208-8 to 208-10)
ோ் ோ
య
ܶ = ܥ௧ (ℎ ) ర (NSCP Eq. 208-12)
Ct = 0.0731 for RC-Moment Frames
Ct = 0.0853 for Steel-Moment Frames
Ct = 0.0488 for all other buildings
V = Design Base Shear
T = Elastic fundamental period of vibration, in seconds
W = structure’s dead weight
x. Dynamic Analysis (NSCP Section 208.5.3)
A dynamic analysis particularly the Response Spectrum Analysis will be
performed in accordance to the requirements of Section 208.5.3.5 of the NSCP
2015 Edition. Response Spectrum Analysis is an elastic dynamic analysis utilizing
the peak dynamic response of all modes having a significant contribution to the
total structural response. Peak modal responses are calculated using the
ordinates of the appropriate response spectrum curve which correspond to the
modal periods. Maximum modal contributions are combined in a statistical
manner, particularly the CQC Method, to obtain an approximate total structural
response.
WIND LOADS (Section 207, NSCP 2015)
i. Basic Wind Speed, V (NSCP Figure 207A.5-1A, B or C) 260kph
ii. Wind directionality factor, Kd (Section 207A.6) 0.85
iii. Exposure category (Section 207A.7) C
iv. Topographic Factor, Kzt (Section 207A.8) 1.0
v. Gust Effect Factor (Section 207A.9) 0.85
vi. Enclosure Classification (Section 207A.10) Enclosed Bldg
vii. Internal Pressure Coefficient, GCpi (Section 207A.11) 0.18
4. LOAD COMBINATIONS
NSCP Section 203.3.1 (For Concrete Members = Using Strength Design Method, For
Steel Members = Using LRFD Method)
i. 1.4 (D + F) NSCP Eq. 203-1
ii. 1.2 (D + F) + 1.6 (L + H) + 0.5 (L r or R) NSCP Eq. 203-2
iii. 1.2 D + 1.6 (Lr or R) + (f1L or 0.5W) NSCP Eq. 203-3
iv. 1.2 D + 1.0W + f1L + 0.5 (Lr or R) NSCP Eq. 203-4
v. 1.2 D + 1.0E + f1L NSCP Eq. 203-5
vi. 0.9 D + 1.0W + 1.6H NSCP Eq. 203-6
vii. 0.9 D + 1.0E +1.6H NSCP Eq. 203-7
NSCP Section 203.4.1 (For Foundation Loads = Using Service Loads Combination)
i. D + F NSCP Eq. 203-8
ii. D + H + F + L NSCP Eq. 203-9
iii. D + H + F + (Lr or R) NSCP Eq. 203-10
iv. D + H + F + 0.75 [L + (Lr or R)] NSCP Eq. 203-11
v. D + H + F + (0.6W or E/1.4) NSCP Eq. 203-12
Where:
D = Dead Load
E = Earthquake Load
F = Load due to fluids
H = Load due to lateral pressure of soil
L = Live Load except Roof Live Load
Lr = Roof Live Load
R = Rain Load
W = Load due to wind pressure
f1 = 1.0 for floors with live loads in excess of 4.8kPa
= 0.5 for other live loads
5. MATERIAL SPECIFICATIONS
CONCRETE: Minimum specified 28-day concrete compressive strength, fc’
i. Footings (Spread, Combined, Mat) 20.7 MPa (3,000 psi)
ii. Columns 27.6 MPa (4,000 psi)
iii. Girders, Beams and Suspended Slabs 27.6 MPa (4,000 psi)
iv. Slab-on-grade 20.7 MPa (3,000 psi)
REINFORCING STEEL BARS: Minimum specified yield strength of reinforcing bars, fy
i. For 16mm diameter bars and above 414 MPa (60 ksi)
ii. For 12mm diameter bars and below 276 MPa (40 ksi)
STRUCTURAL STEEL:
i. Minimum specified yield strength of structural steel, fy
1. For hot-rolled steel 250 MPa (36 ksi)
2. For Cold-formed steel 230 MPa (30 ksi)
ii. Fillet Weld (E70 Electrodes), Fu 480 MPa (70 ksi)
iii. All Bolts shall be High Tensile Strength ASTM A325
6. FOUNDATION DESIGN
Allowable Foundation Pressure
i. Assumed Allowable Foundation Pressure, q allow 144kPa (3,000 psf)
Allowable Pile Load Capacity (if any)
i. Assumed Allowable Pile Load Capacity, P allow 1,000 kN (100 MTons)
Note: Please refer to the Geotechnical Investigation Report if available
7. STRUCTURAL ANALYSIS & DESIGN
The structural design of the members will be performed using the following
programs:
i. Foundation Design Using Excel Program
ii. Frame Members Using Excel Program
Civil/Structural Engineer:
Engr. Jayward T. Laput, CE, RMP
PRC No. 138139 PTR No. 2754424
Date: 05-16-2015 Date: 01-08-2025
TIN No. 322-467-389 Place: CEBU CITY
STRUCTURAL PLANS
DESIGN OF FOOTINGS
ANALYSIS AND DESIGN OF FOOTINGS
PROJECT: Proposed Two-Storey Residential Building
LOCATION: Velpal Phase 2, Blk 2, Lot 1, Pakigne, Minglanilla
OWNER: Gladdes Salatan Spannbauer
STRUCTURAL: Engr. Jayward T. Laput ce, rmp
Mark: F1 Design Specifications: Load Data: Preliminary A( m2) = 0.84
fc' = 20.7 Mpa Pu = 164.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 6.00 kN.m required B (m) = 1.04
qa = 144 kPa Mux = 7.00 kN.m Trial Footing Dimension :
Column Dimension: P= 109.33 kN try L (m) = 1.4
a1 = 0.3 m W footing = 10.93 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.037 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.043 m qmax = 80.31 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 18.99 kN.m Mu = 18.99 kN.m
d = 0.2 m Ru = 0.38 MPa Ru = 0.38 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 43.94 kN req'd p = 0.00092 req'd p = 0.00092
qumax = 112.10 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 55.25 kPa safe for beam shear! use p = 0.00123 use p = 0.00123
use q u = 89.68 kPa Check for Punching Shear: As = 343.49 mm2 As = 343.49 mm2
Enter Bar Diameter: Vu = 141.58 kN req'd n2 = 1.71 pcs req'd n2 = 1.71 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 7 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 181.33 OK!
Mark: F1 Design Specifications: Load Data: Preliminary A( m2) = 0.94
fc' = 20.7 Mpa Pu = 185.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 29.00 kN.m required B (m) = 1.18
qa = 144 kPa Mux = 7.00 kN.m Trial Footing Dimension :
Column Dimension: P= 123.33 kN try L (m) = 1.4
a1 = 0.3 m W footing = 12.33 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.157 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.038 m qmax = 121.70 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 29.32 kN.m Mu = 29.32 kN.m
d = 0.2 m Ru = 0.58 MPa Ru = 0.58 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 67.86 kN req'd p = 0.00143 req'd p = 0.00143
qumax = 173.10 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 15.67 kPa safe for beam shear! use p = 0.00191 use p = 0.00191
use q u = 138.48 kPa Check for Punching Shear: As = 533.65 mm2 As = 533.65 mm2
Enter Bar Diameter: Vu = 150.38 kN req'd n2 = 2.65 pcs req'd n2 = 2.65 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 7 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 181.33 OK!
Mark: F1 Design Specifications: Load Data: Preliminary A( m2) = 0.90
fc' = 20.7 Mpa Pu = 177.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 7.00 kN.m required B (m) = 1.13
qa = 144 kPa Mux = 28.00 kN.m Trial Footing Dimension :
Column Dimension: P= 118.00 kN try L (m) = 1.4
a1 = 0.3 m W footing = 11.80 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.040 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.158 m qmax = 117.24 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 28.26 kN.m Mu = 28.26 kN.m
d = 0.2 m Ru = 0.56 MPa Ru = 0.56 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 65.40 kN req'd p = 0.00138 req'd p = 0.00138
qumax = 166.84 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 13.78 kPa safe for beam shear! use p = 0.00184 use p = 0.00184
use q u = 133.47 kPa Check for Punching Shear: As = 514.00 mm2 As = 514.00 mm2
Enter Bar Diameter: Vu = 143.63 kN req'd n2 = 2.56 pcs req'd n2 = 2.56 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 7 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 181.33 OK!
ANALYSIS AND DESIGN OF FOOTINGS
PROJECT: Proposed Two-Storey Residential Building
LOCATION: Velpal Phase 2, Blk 2, Lot 1, Pakigne, Minglanilla
OWNER: Gladdes Salatan Spannbauer
STRUCTURAL: Engr. Jayward T. Laput ce, rmp
Mark: CF-1 Design Specifications: Load Data: Preliminary A( m2) = 1.00
fc' = 20.7 Mpa Pu = 197.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 7.00 kN.m required B (m) = 1.25
qa = 144 kPa Mux = 7.00 kN.m Trial Footing Dimension :
Column Dimension: P= 131.33 kN try L (m) = 2.8
a1 = 0.3 m W footing = 13.13 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.036 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.036 m qmax = 44.51 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 54.97 kN.m Mu = 21.28 kN.m
d = 0.2 m Ru = 1.09 MPa Ru = 0.21 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 73.88 kN req'd p = 0.00272 req'd p = 0.00051
qumax = 61.73 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 38.78 kPa safe for beam shear! use p = 0.00338 use p = 0.00068
use q u = 50.26 kPa Check for Punching Shear: As = 946.86 mm2 As = 383.11 mm2
Enter Bar Diameter: Vu = 184.44 kN req'd n2 = 4.71 pcs req'd n2 = 1.91 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 14 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 182.77 OK!
Mark: CF-1 Design Specifications: Load Data: Preliminary A( m2) = 1.03
fc' = 20.7 Mpa Pu = 202.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 29.00 kN.m required B (m) = 1.29
qa = 144 kPa Mux = 7.00 kN.m Trial Footing Dimension :
Column Dimension: P= 134.67 kN try L (m) = 2.8
a1 = 0.3 m W footing = 13.47 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.144 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.035 m qmax = 53.46 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 65.66 kN.m Mu = 25.42 kN.m
d = 0.2 m Ru = 1.30 MPa Ru = 0.25 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 88.24 kN req'd p = 0.00327 req'd p = 0.00061
qumax = 75.04 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 28.02 kPa safe for beam shear! use p = 0.00338 use p = 0.00082
use q u = 60.03 kPa Check for Punching Shear: As = 946.86 mm2 As = 458.17 mm2
Enter Bar Diameter: Vu = 186.99 kN req'd n2 = 4.71 pcs req'd n2 = 2.28 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 14 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 182.77 OK!
Mark: CF-1 Design Specifications: Load Data: Preliminary A( m2) = 1.01
fc' = 20.7 Mpa Pu = 198.00 kN assume L (m) = 0.8
n2 My Muy =
fy = 414 MPa 7.00 kN.m required B (m) = 1.26
qa = 144 kPa Mux = 32.00 kN.m Trial Footing Dimension :
Column Dimension: P= 132.00 kN try L (m) = 2.8
a1 = 0.3 m W footing = 13.20 kN try B(m) = 1.4
a2 = 0.3 m eux = 0.035 m Check Footing Dimension:
B a2 Mx Depth from bottom to NGL: euy = 0.162 m qmax = 62.92 kPa
a1 H = 1.4 m qa,adj = 144.00 kPa Footing Dimension is OK!
n1
Trial Footing Thickness: Design of steel in x-dir: Design of steel in y-dir:
try t = 0.3 m Mu = 78.16 kN.m Mu = 30.26 kN.m
d = 0.2 m Ru = 1.55 MPa Ru = 0.30 MPa
L
Check for Beam Shear: m = 23.529412 m = 23.529412
Ultimate Soil Pressures : Vu = 105.04 kN req'd p = 0.00393 req'd p = 0.00073
qumax = 89.32 kPa fVc = 180.47 kN min p = 0.00338 min p = 0.00338
qu,min = 11.70 kPa safe for beam shear! use p = 0.00393 use p = 0.00098
use q u = 71.46 kPa Check for Punching Shear: As = 1099.61 mm2 As = 546.16 mm2
Enter Bar Diameter: Vu = 180.14 kN req'd n2 = 5.47 pcs req'd n2 = 2.72 pcs
bar f = 16 mm fVc = 515.64 kN use n2 = 7 pcs use n2 = 14 pcs
Ab = 201.06 mm2 safe for punching shear! s (mm) = 181.33 OK! s (mm) = 182.77 OK!
**************************************************** 85. END GROUP DEFINITION 155. ZONE 0.4 I 1 RWX 8.5 RWZ 8.5 STYP 4 CT 0.0731 NA 1 NV 1
* * 86. DEFINE MATERIAL START 156. REFERENCE LOAD Y
* STAAD.Pro V8i SELECTseries6 * 87. ISOTROPIC CONCRETE
* Version 20.07.11.33 * 88. E 2.17185E+007 *** NOTE: SEISMIC WEIGHT TABLE IS PRESENT.THIS WEIGHT TABLE
* Proprietary Program of * 89. POISSON 0.17 WILL BE CONSIDERED IN STATIC SEISMIC ANALYSIS.
* Bentley Systems, Inc. * 90. DENSITY 23.5616
* Date= JUN 19, 2025 * 91. ALPHA 1E-005 157. R1 1.0
* Time= 13:16:20 * 92. DAMP 0.05 158. LOAD 1 LOADTYPE SEISMIC TITLE EX
* * 93. TYPE CONCRETE 159. UBC LOAD X 1 DEC 1 ACC 0.05
* USER ID: HP * 94. STRENGTH FCU 27579 160. PERFORM ANALYSIS
**************************************************** DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 3 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 5
95. ISOTROPIC STEEL
96. E 2.05E+008
1. STAAD SPACE DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF 97. POISSON 0.3
INPUT FILE: E:\1. PROJECTS\242 - Proposed 2-Storey House Minglanilla\Staad\2-Storey 98. DENSITY 76.8195 P R O B L E M S T A T I S T I C S
Residence Minglani.. .STD 99. ALPHA 1.2E-005 -----------------------------------
2. START JOB INFORMATION 100. DAMP 0.03
3. ENGINEER DATE 19-JUN-25 101. TYPE STEEL NUMBER OF JOINTS 139 NUMBER OF MEMBERS 266
4. END JOB INFORMATION 102. STRENGTH FY 253200 FU 407800 RY 1.5 RT 1.2 NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
5. INPUT WIDTH 79 103. END DEFINE MATERIAL NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 12
6. UNIT METER KN 104. MEMBER PROPERTY AMERICAN
7. JOINT COORDINATES 105. 1 TO 12 35 TO 46 PRIS YD 0.3 ZD 0.3
8. 1 0 0 0; 2 0 3 0; 3 2.15 0 0; 4 2.15 3 0; 5 6.25 0 0; 6 6.25 3 0; 7 8.4 0 0 106. 47 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 154 160 163 172 173 - SOLVER USED IS THE IN-CORE ADVANCED MATH SOLVER
9. 8 8.4 3 0; 9 2.15 0 -4.35; 10 2.15 3 -4.35; 11 0 0 -4.35; 12 0 3 -4.35 107. 179 186 190 193 TO 195 PRIS YD 0.3 ZD 0.2
10. 13 6.25 0 -4.35; 14 6.25 3 -4.35; 15 8.4 0 -4.35; 16 8.4 3 -4.35; 17 8.4 0 -7 108. 13 TO 34 PRIS YD 0.4 ZD 0.2 TOTAL PRIMARY LOAD CASES = 1, TOTAL DEGREES OF FREEDOM = 717
11. 18 8.4 3 -7; 19 0 0 -6.78; 20 0 3 -6.78; 21 2.15 0 -6.83631 109. MEMBER PROPERTY AMERICAN TOTAL LOAD COMBINATION CASES = 0 SO FAR.
12. 22 2.15 3 -6.83631; 23 6.25 0 -6.94369; 24 6.25 3 -6.94369; 25 4.2 3 0 110. 65 69 72 75 78 80 83 86 89 92 95 98 TO 113 115 TO 118 120 122 TO 131 133 135 -
13. 26 4.2 3 -6.89; 27 4.2 3 -4.35; 28 0 6 -6.78; 29 6.25 6 -6.94369; 30 8.4 6 -7 111. 136 138 147 149 151 152 155 156 159 161 165 167 TO 169 171 175 176 178 180 -
14. 31 6.25 6 -4.35; 32 2.15 6 -6.83631; 33 6.25 6 0; 34 2.15 6 0; 35 2.15 6 -4.35 112. 181 TO 182 184 187 189 197 TO 199 201 TABLE SD L20203
15. 36 0 6 -4.35; 37 0 6 0; 38 8.4 6 0; 39 8.4 6 -4.35; 40 4.2 6 0; 41 0 6 -0.35 113. 64 66 TO 68 70 71 74 77 79 82 85 88 91 94 97 114 119 132 134 137 139 150 157 - VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05
16. 42 0 6 -5.2; 43 4.2 6 -6.89; 44 4.2 6 -4.35; 45 8.4 6 -0.35; 46 8.4 6 -5.2 114. 158 162 164 166 170 174 177 183 185 188 191 192 196 200 204 205 207 208 210 - -------- ---------- --------------
17. 47 8.4 6.3 0; 48 8.4 7 -7; 49 8.4 6.97381 -6.73809; 50 8.4 6.2597 0.402978 115. 211 TO 212 214 216 217 224 225 227 229 TO 231 233 235 TO 237 239 243 244 246 -
18. 51 8.4 5.95 0.5; 52 8.4 6.2 1; 53 8.4 5.9 1; 54 8.4 6.25 0.5; 55 8.4 6 -6 116. 248 TO 250 252 254 TO 256 258 260 262 263 TABLE SD L20204 STORY FL. LEVEL IN METE S T A T U S
19. 56 8.4 6.9 -6; 57 8.4 6.8544 -5.54404; 58 8.4 6.82 -5.2 117. MEMBER PROPERTY COLDFORMED AMERICAN ----- ----------------- --------------------
20. 59 8.4 6.7947 -4.94702; 60 8.4 6.735 -4.35; 61 8.4 6.67411 -3.74107 118. 202 203 206 209 213 215 218 TO 223 226 228 232 234 238 240 TO 242 245 247 - X Z
21. 62 8.4 6 -3.55; 63 8.4 6.655 -3.55; 64 8.4 6.6144 -3.14404; 65 8.4 6 -2.75 119. 251 253 257 259 261 264 TO 266 TABLE ST JW4X057CS
22. 66 8.4 6.575 -2.75; 67 8.4 6.5547 -2.54702; 68 8.4 6 -1.95; 69 8.4 6.495 -1.95 120. CONSTANTS 1 3.00 OK OK
23. 70 8.4 6.435 -1.35; 71 8.4 6 -1.35; 72 8.4 6.375 -0.75; 73 8.4 6 -0.75 121. MATERIAL CONCRETE MEMB 1 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 -
24. 74 8.4 6.335 -0.35; 75 8.4 6.3194 -0.194045; 76 0 6 -6; 77 0 6.82 -5.2 122. 153 154 160 163 172 173 179 186 190 193 TO 195 NOTE : NO SOFT STOREY IS DETECTED.
25. 78 0 6.375 -0.75; 79 0 6 -1.35; 80 0 6 -3.55; 81 0 6.655 -3.55 123. MATERIAL STEEL MEMB 64 TO 72 74 75 77 TO 80 82 83 85 86 88 89 91 92 94 95 -
26. 82 0 6.735 -4.35; 83 0 6.67411 -3.74107; 84 0 6.9 -6; 85 0 6.435 -1.35 124. 97 TO 120 122 TO 139 147 149 TO 152 155 TO 159 161 162 164 TO 171 -
27. 86 0 6 -2.75; 87 0 6.575 -2.75; 88 0 6.495 -1.95; 89 0 6 -1.95 125. 174 TO 178 180 TO 185 187 TO 189 191 192 196 TO 266
28. 90 0 6.335 -0.35; 91 0 6 -0.75; 92 0 6.2 1; 93 0 5.9 1; 94 0 6.25 0.5 126. SUPPORTS ***********************************************************
29. 95 0 6.3 0; 96 0 5.95 0.5; 97 4.2 6.375 -0.75; 98 4.2 6 -1.35; 99 4.2 6 -1.95 127. 1 3 5 7 9 11 13 15 17 19 21 23 FIXED * *
30. 100 4.2 6.735 -4.35; 101 4.2 6 -5.2; 102 4.2 6.9 -6; 103 4.2 6.8544 -5.54404 128. MEMBER RELEASE * X DIRECTION : Ta = 0.315 Tb = 0.406 Tuser = 0.000 *
31. 104 4.2 6 -6; 105 4.2 6.82 -5.2; 106 4.2 6 -0.35; 107 4.2 6.7947 -4.94702 129. 31 64 65 68 75 78 80 83 86 89 92 95 98 100 102 TO 105 107 TO 109 111 113 116 - * T = 0.406, LOAD FACTOR = 1.000 *
32. 108 4.2 6.435 -1.35; 109 4.2 6 -3.55; 110 4.2 6.655 -3.55 130. 117 TO 118 120 122 TO 129 131 TO 134 136 153 156 160 166 171 182 185 197 - * UBC TYPE = 97 *
33. 111 4.2 6.67411 -3.74107; 112 4.2 6 -2.75; 113 4.2 6.335 -0.35; 114 4.2 6.3 0 131. 199 START MX MZ * UBC FACTOR V = 0.1294 x 1151.98 = 149.08 KN *
34. 115 4.2 5.95 0.5; 116 4.2 6.2 1; 117 4.2 6.575 -2.75; 118 4.2 5.9 1 132. 34 99 101 106 112 115 172 190 198 201 END MX MZ * *
35. 119 4.2 6.2597 0.402978; 120 4.2 6.25 0.5; 121 4.2 6.3194 -0.194045 133. 202 206 213 218 220 222 226 232 238 241 245 251 257 261 START MX MY MZ ***********************************************************
36. 122 4.2 6 -0.75; 123 4.2 6.5547 -2.54702; 124 4.2 6.495 -1.95 134. 203 209 215 219 221 223 228 234 240 242 247 253 259 264 TO 266 END MX MY MZ
37. 125 4.2 6.6144 -3.14404; 126 4.2 6.989 -6.89; 127 4.2 6.97381 -6.73809 135. MEMBER CRACKED ************************************************************************
38. 128 0 6.978 -6.78; 129 0 6.97381 -6.73809; 130 0 6.2597 0.402978 136. 1 TO 12 35 TO 46 REDUCTION RIY 0.700000 RIZ 0.700000
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 2 137. 13 TO 34 47 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 154 160 163 -
138. 172 173 179 186 190 193 TO 195 REDUCTION RIY 0.350000 RIZ 0.350000
39. 131 0 6.3194 -0.194045; 132 0 6.5547 -2.54702; 133 0 6.6144 -3.14404 139. DEFINE REFERENCE LOADS ***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.
40. 134 0 6.7947 -4.94702; 135 0 6.8544 -5.54404; 136 0 6.91411 -6.14107 140. LOAD R1 LOADTYPE DEAD TITLE REF LOAD 1 TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
41. 137 8.4 6.91411 -6.14107; 138 4.2 6.91411 -6.14107 141. SELFWEIGHT Y 1 DYNAMIC ECCENTRICITY APPLIED = DEC - 1
42. MEMBER INCIDENCES 142. MEMBER LOAD DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 6
43. 1 1 2; 2 3 4; 3 5 6; 4 7 8; 5 9 10; 6 11 12; 7 13 14; 8 15 16; 9 17 18 143. 13 TO 22 30 32 UNI GY 10.5
44. 10 19 20; 11 21 22; 12 23 24; 13 2 4; 14 4 25; 15 6 8; 16 8 16; 17 16 18 144. 202 203 206 209 213 215 218 TO 223 226 228 232 234 238 240 TO 242 245 247 -
45. 18 2 12; 19 12 20; 20 20 22; 21 22 26; 22 24 18; 23 6 14; 24 14 24; 25 22 10 145. 251 253 257 259 261 264 TO 266 UNI GY 0.6
46. 26 10 4; 27 12 10; 28 10 27; 29 14 16; 30 25 6; 31 25 27; 32 26 24; 33 27 14 146. 52 TO 54 194 UNI GY 7 LOAD NO.: 1 DIRECTION : X UNIT - METE
47. 34 27 26; 35 20 28; 36 24 29; 37 18 30; 38 14 31; 39 22 32; 40 6 33; 41 4 34 147. 50 51 62 63 73 76 81 84 87 90 93 96 121 140 TO 146 UNI GY 3.5
48. 42 10 35; 43 12 36; 44 2 37; 45 8 38; 46 16 39; 47 37 34; 48 34 40; 49 33 38 148. FLOOR LOAD STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
49. 50 37 41; 51 36 42; 52 28 32; 53 29 30; 54 32 43; 55 34 35; 56 35 32; 57 33 31 149. _2FLOAD FLOAD 5 GY ----- ----- --------------- --------------- ---------------
50. 58 31 29; 59 36 35; 60 35 44; 61 31 39; 62 38 45; 63 39 46; 64 38 47; 65 30 48 150. END DEFINE REFERENCE LOADS X Z X Z X Z
51. 66 48 49; 67 47 50; 68 38 51; 69 52 53; 70 51 53; 71 54 52; 72 51 54; 73 55 30 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 4 dec + aec dec + aec
52. 74 56 57; 75 55 56; 76 46 55; 77 58 59; 78 46 58; 79 60 61; 80 39 60; 81 62 39
53. 82 63 64; 83 62 63; 84 65 62; 85 66 67; 86 65 66; 87 68 65; 88 69 70; 89 68 69 151. FLOOR DIAPHRAGM 1 3.00 0.00 0.00 0.42 0.35 0.00 0.35
54. 90 71 68; 91 70 72; 92 71 70; 93 73 71; 94 72 74; 95 73 72; 96 45 73; 97 74 75 152. DIA 1 TYPE RIG HEI 3 JOINT 2 4 6 8 10 12 14 16 18 20 22 24 TO 27
55. 98 45 74; 99 56 30; 100 55 58; 101 60 46; 102 39 63; 103 62 66; 104 65 69 153. CHECK SOFT STORY ASCE7 ************************************************************************
56. 105 68 70; 106 72 71; 107 73 74; 108 45 47; 109 38 54; 110 51 52; 111 76 77
57. 112 78 79; 113 80 81; 114 82 83; 115 82 42; 116 76 84; 117 42 77; 118 36 82 *** NOTE: NEITHER "MASS" NOR "GRAVITY" REFERENCE LOADTYPE IS PRESENT.
58. 119 85 78; 120 79 85; 121 76 28; 122 86 87; 123 80 87; 124 86 88; 125 89 88 MASS MODEL IS FORMED BY COMBINING ALL "DEAD" AND "LIVE" (IF ANY)
59. 126 36 81; 127 41 90; 128 91 90; 129 91 78; 130 92 93; 131 37 94; 132 37 95 REFERENCE LOADTYPES. 161. CHANGE
60. 133 89 85; 134 37 96; 135 96 94; 136 41 95; 137 96 93; 138 96 92; 139 88 85 162. LOAD 2 LOADTYPE SEISMIC TITLE EZ
61. 140 41 91; 141 42 76; 142 91 79; 143 79 89; 144 80 36; 145 86 80; 146 89 86 *** NOTE: MASS MODEL FORMED WILL BE USED IN SEISMIC/RESPONSE/TIME HISTORY LOADING, 163. UBC LOAD Z 1 DEC 1 ACC 0.05
62. 147 97 98; 148 98 99; 149 100 101; 150 102 103; 151 104 105; 152 104 102 IF ANY. 164. PERFORM ANALYSIS
63. 153 40 106; 154 101 104; 155 101 105; 156 44 100; 157 105 107; 158 108 97 IF MASS MODEL IS SEPARATELY PROVIDED IN INDIVIDUAL LOADING, THE GENERATED
64. 159 98 108; 160 44 101; 161 109 110; 162 100 111; 163 112 109; 164 97 113 MASS
65. 165 106 114; 166 40 114; 167 115 116; 168 109 117; 169 116 118; 170 114 119 WILL BE REPLACED BY THE MASS PROVIDED IN INDIVIDUAL LOADING. ***********************************************************
66. 171 40 120; 172 104 43; 173 99 112; 174 113 121; 175 112 117; 176 99 108 * *
67. 177 120 116; 178 115 120; 179 106 122; 180 122 113; 181 106 113; 182 44 110 * Z DIRECTION : Ta = 0.315 Tb = 0.420 Tuser = 0.000 *
68. 183 117 123; 184 112 124; 185 40 115; 186 122 98; 187 122 97; 188 124 108 * T = 0.315, LOAD FACTOR = 1.000 *
69. 189 99 124; 190 109 44; 191 110 125; 192 115 118; 193 40 33; 194 43 29 * UBC TYPE = 97 *
70. 195 44 31; 196 126 127; 197 43 126; 198 102 43; 199 28 128; 200 128 129 ************************************************************************************ * UBC FACTOR V = 0.1294 x 1151.98 = 149.08 KN *
71. 201 84 28; 202 92 116; 203 116 52; 204 92 94; 205 94 130; 206 130 119 * *
72. 207 50 54; 208 119 120; 209 119 50; 210 130 95; 211 95 131; 212 75 47 FLOOR DIAPHRAGM UNIT - KN METE ***********************************************************
73. 213 131 121; 214 121 114; 215 121 75; 216 90 131; 217 78 90; 218 78 97 --------------- ----------------
74. 219 97 72; 220 85 108; 221 108 70; 222 88 124; 223 124 69; 224 132 88 ************************************************************************
75. 225 67 69; 226 132 123; 227 123 124; 228 123 67; 229 132 87; 230 87 133 NO. TYPE FL. LEVEL FL. WT CENTRE OF MASS MASTER JOINT NO.
76. 231 64 66; 232 133 125; 233 125 117; 234 125 64; 235 133 81; 236 81 83 X Z
77. 237 61 63; 238 83 111; 239 111 110; 240 111 61; 241 82 100; 242 100 60
78. 243 134 82; 244 59 60; 245 134 107; 246 107 100; 247 107 59; 248 134 77 1 RIGID 3.000 799.28 4.223 -3.517 139 ***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.
79. 249 77 135; 250 57 58; 251 135 103; 252 103 105; 253 103 57; 254 135 84 TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
80. 255 84 136; 256 137 56; 257 136 138; 258 138 102; 259 138 137; 260 49 137 DYNAMIC ECCENTRICITY APPLIED = DEC - 1
81. 261 49 127; 262 127 138; 263 129 136; 264 127 129; 265 126 128; 266 126 48 ************************************************************************************
82. START GROUP DEFINITION
83. FLOOR LOAD NO.: 2 DIRECTION : Z UNIT - METE
84. _2FLOAD 13 TO 34 154. DEFINE UBC LOAD
STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC. 7 -2.94 145.65 1.46 1.98 0.00 2.92
----- ----- --------------- --------------- --------------- CENTRE OF RIGIDITY UNIT - METE 8 -15.90 138.82 1.64 2.26 -0.08 24.97
X Z X Z X Z ------------------ ----------- 9 9.63 175.45 1.15 1.61 0.09 -18.74
dec + aec dec + aec 10 -2.60 135.82 -10.30 -19.88 -0.11 2.38
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 7 DIAPHRAM FL. LEVEL X-COORDINATE Z-COORDINATE 11 -3.66 178.45 13.08 23.76 0.12 3.85
1 3.00 0.00 0.00 0.42 0.35 0.42 0.00 1 3.000 4.181 -3.746 ************** END OF LATEST ANALYSIS RESULT **************
************************************************************************ ************************************************************
203. PARAMETER 1
204. CODE LRFD
202. PRINT SUPPORT REACTION LIST 1 3 5 7 9 11 13 15 17 19 21 23 205. CHECK CODE MEMB 64 TO 72 74 75 77 TO 80 82 83 85 86 88 89 91 92 94 95 -
165. CHANGE DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 10 206. 97 TO 120 122 TO 139 147 149 TO 152 155 TO 159 161 162 164 TO 171 -
166. LOAD 3 LOADTYPE DEAD TITLE DL 207. 174 TO 178 180 TO 185 187 TO 189 191 192 196 TO 201 204 205 207 208 -
167. REFERENCE LOAD 208. 210 TO 212 214 216 217 224 225 227 229 TO 231 233 235 TO 237 239 243 244 -
168. R1 -1.0 209. 246 248 TO 250 252 254 TO 256 258 260 262 263
169. LOAD 4 LOADTYPE LIVE TITLE LL DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 12
170. MEMBER LOAD SUPPORT REACTIONS -UNIT KN METE STRUCTURE TYPE = SPACE
171. 25 UNI GY -4.8 -----------------
172. FLOOR LOAD
173. _2FLOAD FLOAD -1.9 GY JOINT LOAD FORCE-X FORCE-Y FORCE-Z MOM-X MOM-Y MOM Z
**NOTE** about Floor/OneWay Loads/Weights. STAAD.Pro CODE CHECKING - (LRFD 3RD EDITION) v1.0
Please note that depending on the shape of the floor you may ***********************
have to break up the FLOOR/ONEWAY LOAD into multiple commands. 1 6 0.87 105.51 -7.27 -6.66 0.00 -0.87
For details please refer to Technical Reference Manual 7 0.82 98.65 -7.24 -6.61 0.00 -0.81
Section 5.32.4.2 Note d and/or "5.32.4.3 Note f. 8 -11.33 84.12 -7.95 -7.58 -0.08 20.83
9 13.07 130.64 -7.24 -6.32 0.09 -22.56
174. LOAD 5 LOADTYPE ROOF LIVE TITLE RL 10 0.41 116.69 -18.74 -28.71 -0.11 -0.09 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)
175. MEMBER LOAD 11 1.33 98.07 3.56 14.81 0.12 -1.64
176. 202 203 206 209 213 215 218 TO 223 226 228 232 234 238 240 TO 242 245 247 - 3 6 4.22 159.79 -5.13 -4.54 0.00 -4.19 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/
177. 251 253 257 259 261 264 TO 266 UNI GY -0.6 7 4.33 162.78 -6.22 -5.62 0.00 -4.29 FX MY MZ LOCATION
178. LOAD COMB 6 1.4DL 8 -9.24 183.42 -5.86 -5.38 -0.08 18.76 =======================================================================
179. 3 1.4 9 18.29 148.89 -5.54 -4.77 0.09 -27.73
180. LOAD COMB 7 1.2DL+1.6LL+0.5RL 10 4.02 175.70 -16.36 -26.19 -0.11 -3.67
181. 3 1.2 4 1.6 5 0.5 11 5.03 156.61 4.96 16.03 0.12 -5.31 64 SD L20204 (AISC SECTIONS)
182. LOAD COMB 8 1.4DL+0.5LL+1.0EX 5 6 -4.20 159.77 -5.13 -4.56 0.00 4.15 PASS LRFD-H1-1B-T 0.347 10
183. 3 1.4 4 0.5 1 1.0 7 -4.33 162.89 -6.29 -5.69 0.00 4.29 6.92 T -0.82 0.00 0.00
184. LOAD COMB 9 1.4DL+0.5LL-1.0EX 8 -18.27 149.00 -5.60 -4.91 -0.08 27.70 65 SD L20203 (AISC SECTIONS)
185. 3 1.4 4 0.5 1 -1.0 9 9.26 183.36 -5.85 -5.32 0.09 -18.79 PASS LRFD-H1-1B-C 0.157 10
186. LOAD COMB 10 1.4DL+0.5LL+1.0EZ 10 -5.01 175.02 -15.95 -25.48 -0.11 5.27 2.71 C -0.27 0.00 0.00
187. 3 1.4 4 0.5 2 1.0 11 -4.00 157.34 4.50 15.25 0.12 3.64 66 SD L20204 (AISC SECTIONS)
188. LOAD COMB 11 1.4DL+0.5LL-1.0EZ 7 6 -0.85 105.35 -7.28 -6.68 0.00 0.84 PASS LRFD-H1-1B-C 0.172 8
189. 3 1.4 4 0.5 2 -1.0 7 -0.82 98.54 -7.24 -6.64 0.00 0.81 0.12 C 0.27 -0.17 0.26
190. LOAD COMB 12 0.9DL+1.0EX 8 -13.05 130.59 -7.28 -6.45 -0.08 22.53 67 SD L20204 (AISC SECTIONS)
191. 3 0.9 1 1.0 9 11.35 83.88 -7.91 -7.49 0.09 -20.86 PASS LRFD-H1-1B-T 0.130 8
192. LOAD COMB 13 0.9DL-1.0EX 10 -1.32 117.33 -17.84 -27.19 -0.11 1.62 7.10 T -0.15 0.10 0.00
193. 3 0.9 1 -1.0 11 -0.38 97.14 2.64 13.25 0.12 0.06 68 SD L20204 (AISC SECTIONS)
194. LOAD COMB 14 0.9DL+1.0EZ 9 6 4.92 167.44 4.48 4.98 0.00 -4.87 PASS LRFD-H1-1B-C 0.042 9
195. 3 0.9 2 1.0 7 5.94 195.79 4.74 5.24 0.00 -5.87 2.42 C 0.09 -0.00 0.50
196. LOAD COMB 15 0.9DL-1.0EZ 8 -7.54 200.89 4.54 4.91 -0.08 16.84 69 SD L20203 (AISC SECTIONS)
197. 3 0.9 2 -1.0 9 18.60 163.71 4.99 5.66 0.09 -27.78 PASS LRFD-H1-1B-T 0.023 8
198. PERFORM ANALYSIS 10 5.60 196.52 -10.08 -19.97 -0.11 -5.56 0.02 T 0.02 0.02 0.00
11 5.45 168.08 19.61 30.54 0.12 -5.38 70 SD L20204 (AISC SECTIONS)
11 6 0.17 138.13 5.05 5.54 0.00 -0.17 PASS LRFD-H1-1B-C 0.023 8
199. LOAD LIST 6 TO 11 7 0.24 130.43 5.05 5.55 0.00 -0.23 0.08 C -0.04 0.01 0.00
200. PRINT STORY DRIFT 0.004200 8 -11.34 116.36 4.84 5.09 -0.08 20.60 71 SD L20204 (AISC SECTIONS)
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 8 9 11.70 165.88 5.72 6.51 0.09 -20.94 PASS LRFD-H1-1B-T 0.067 8
10 0.21 154.17 -9.86 -19.91 -0.11 -0.21 2.41 T -0.11 0.03 0.00
11 0.15 128.06 20.41 31.51 0.12 -0.13 72 SD L20203 (AISC SECTIONS)
13 6 -4.92 168.59 4.38 4.87 0.00 4.88 PASS LRFD-H1-1B-T 0.037 9
7 -5.93 187.49 5.25 5.74 0.00 5.88 1.51 T -0.02 0.03 0.00
STORY HEIGHT LOAD AVG. DISP(CM ) DRIFT(CM ) RATIO 8 -18.59 162.40 4.97 5.57 -0.08 27.78 74 SD L20204 (AISC SECTIONS)
STATUS 9 7.55 198.70 4.72 5.15 0.09 -16.83 PASS LRFD-H1-1B-T 0.126 11
----------------------------------------------------------------------------------- 10 -5.53 193.08 -9.40 -18.99 -0.11 5.47 1.07 T 0.00 0.22 0.00
------- 11 -5.51 168.01 19.10 29.71 0.12 5.48 75 SD L20203 (AISC SECTIONS)
(METE) X Z X Z 15 6 -0.20 141.50 4.75 5.23 0.00 0.20 PASS LRFD-H1-1B-T 0.268 8
7 -0.26 133.56 4.83 5.32 0.00 0.27 0.86 T -0.06 0.33 0.90
BASE= 0.00 ALLOW. DRIFT = 8 -11.72 169.63 5.33 6.04 -0.08 20.98 77 SD L20204 (AISC SECTIONS)
L / 238 9 11.31 119.44 4.65 4.95 0.09 -20.56 PASS LRFD-H1-1B-C 0.093 7
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 11 1.71 C -0.00 0.16 0.00
78 SD L20203 (AISC SECTIONS)
1 0.00 6 0.0000 0.0000 0.0000 0.0000 L /999999 PASS LRFD-H1-1B-C 0.218 8
PASS 3.87 C -0.03 0.27 0.82
7 0.0000 0.0000 0.0000 0.0000 L /999999 79 SD L20204 (AISC SECTIONS)
PASS SUPPORT REACTIONS -UNIT KN METE STRUCTURE TYPE = SPACE PASS LRFD-H1-1B-T 0.102 8
8 0.0000 0.0000 0.0000 0.0000 L /999999 ----------------- 8.41 T -0.13 -0.09 0.61
PASS 80 SD L20203 (AISC SECTIONS)
9 0.0000 0.0000 0.0000 0.0000 L /999999 JOINT LOAD FORCE-X FORCE-Y FORCE-Z MOM-X MOM-Y MOM Z PASS LRFD-H1-1B-C 0.229 11
PASS 14.60 C 0.34 0.00 0.00
10 0.0000 0.0000 0.0000 0.0000 L /999999 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 13
PASS 10 -0.17 154.51 -8.90 -18.34 -0.11 0.15
11 0.0000 0.0000 0.0000 0.0000 L /999999 11 -0.24 134.56 18.88 29.33 0.12 0.26
PASS 17 6 -0.99 81.87 2.13 2.64 0.00 0.99
7 -0.98 74.44 2.06 2.58 0.00 0.98
2 3.00 6 0.0001 -0.0235 0.0001 0.0235 L / 12790 8 -12.23 108.06 2.62 3.35 -0.08 21.33 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)
PASS 9 10.20 57.75 1.80 2.13 0.09 -19.30
7 0.0003 -0.0238 0.0003 0.0238 L / 12583 10 -0.58 62.76 -9.57 -19.00 -0.11 0.37 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/
PASS 11 -1.45 103.05 13.98 24.48 0.12 1.66 FX MY MZ LOCATION
8 0.4128 -0.0233 0.4128 0.0233 L / 726 19 6 0.96 78.51 1.70 2.23 0.00 -0.94 =======================================================================
PASS 7 0.96 71.45 1.70 2.24 0.00 -0.94
9 -0.4126 -0.0260 0.4126 0.0260 L / 727 8 -10.26 53.86 1.47 1.76 -0.08 19.40
PASS 9 12.23 105.11 2.08 2.91 0.09 -21.32 82 SD L20204 (AISC SECTIONS)
10 0.0023 0.4312 0.0023 0.4312 L / 695 10 1.39 57.19 -11.18 -21.21 -0.11 -1.57 PASS LRFD-H1-1B-T 0.145 11
PASS 11 0.57 101.78 14.73 25.88 0.12 -0.36 4.52 T -0.00 0.25 0.00
11 -0.0020 -0.4806 0.0020 0.4806 L / 624 21 6 2.97 152.57 1.04 1.57 0.00 -2.94 83 SD L20203 (AISC SECTIONS)
PASS 7 2.97 153.54 1.90 2.43 0.00 -2.93 PASS LRFD-H1-1B-T 0.194 8
201. PRINT DIA CR 8 -9.61 176.57 1.29 1.70 -0.08 18.75 7.74 T 0.08 0.19 0.65
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 9 9 15.92 140.91 1.42 2.13 0.09 -24.97 85 SD L20204 (AISC SECTIONS)
10 3.59 134.93 -10.91 -20.79 -0.11 -3.75 PASS LRFD-H1-1B-C 0.170 8
11 2.71 182.56 13.63 24.62 0.12 -2.47 16.61 C 0.10 0.17 0.00
************************************************************ 23 6 -2.96 153.73 1.28 1.80 0.00 2.94 86 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.167 8 PASS LRFD-H1-1B-C 0.337 7
9.28 T 0.08 0.15 0.58 4.25 C -0.00 0.59 0.00
88 SD L20204 (AISC SECTIONS) 117 SD L20203 (AISC SECTIONS) DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 17
PASS LRFD-H1-1B-C 0.101 9 PASS LRFD-H1-1B-C 0.214 8
22.19 C -0.11 -0.02 0.00 2.84 C -0.03 0.27 0.82
89 SD L20203 (AISC SECTIONS) 118 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.103 8 PASS LRFD-H1-1B-C 0.222 11
2.35 T -0.04 0.11 0.50 13.12 C 0.34 0.00 0.00 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)
91 SD L20204 (AISC SECTIONS) 119 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.097 9 PASS LRFD-H1-1B-C 0.097 8 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/
18.97 C -0.07 -0.07 0.00 19.03 C 0.07 -0.07 0.00 FX MY MZ LOCATION
92 SD L20203 (AISC SECTIONS) 120 SD L20203 (AISC SECTIONS) =======================================================================
PASS LRFD-H1-1B-C 0.120 10 PASS LRFD-H1-1B-C 0.120 10
8.03 C 0.18 0.00 0.00 8.02 C 0.18 0.00 0.00
94 SD L20204 (AISC SECTIONS) 122 SD L20203 (AISC SECTIONS) 158 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.135 9 PASS LRFD-H1-1B-T 0.169 8 PASS LRFD-H1-1B-C 0.137 8
8.27 C 0.14 0.11 0.40 9.21 T 0.07 0.15 0.58 26.68 C 0.12 -0.09 0.00
95 SD L20203 (AISC SECTIONS) 123 SD L20203 (AISC SECTIONS) 159 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.169 10 PASS LRFD-H1-1B-C 0.279 8 PASS LRFD-H1-1B-C 0.198 9
12.51 C 0.24 0.00 0.00 16.75 C -0.42 0.00 0.00 6.84 C -0.08 0.19 0.44
97 SD L20204 (AISC SECTIONS) 124 SD L20203 (AISC SECTIONS) 161 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.121 10 PASS LRFD-H1-1B-C 0.145 8 PASS LRFD-H1-1B-T 0.204 8
18.57 T -0.00 0.16 0.00 6.57 C -0.23 0.00 0.00 11.22 T -0.13 0.15 0.00
98 SD L20203 (AISC SECTIONS) 125 SD L20203 (AISC SECTIONS) 162 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.145 11 PASS LRFD-H1-1B-T 0.106 8 PASS LRFD-H1-1B-T 0.177 7
9.20 C 0.22 0.00 0.00 2.36 T -0.04 0.11 0.50 7.72 T 0.00 0.29 0.00
99 SD L20203 (AISC SECTIONS) 126 SD L20203 (AISC SECTIONS) 164 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.584 8 PASS LRFD-H1-1B-C 0.411 8 PASS LRFD-H1-1B-C 0.131 7
4.56 C 1.04 0.00 1.35 13.67 C -0.68 0.00 0.00 16.76 C -0.00 0.17 0.40
100 SD L20203 (AISC SECTIONS) 127 SD L20203 (AISC SECTIONS) 165 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.515 8 PASS LRFD-H1-1B-C 0.144 11 PASS LRFD-H1-1B-T 0.220 8
2.43 T -0.94 0.00 0.00 9.27 C 0.22 0.00 0.00 27.37 T 0.19 0.07 0.00
101 SD L20203 (AISC SECTIONS) 128 SD L20203 (AISC SECTIONS) 166 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.429 8 PASS LRFD-H1-1B-T 0.226 8 PASS LRFD-H1-1B-C 0.589 10
13.02 T 0.73 0.00 1.12 14.50 T -0.35 0.00 0.00 25.70 C -1.32 0.00 0.00
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 14 129 SD L20203 (AISC SECTIONS) 167 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.169 10 PASS LRFD-H1-1B-C 0.068 9
12.50 C 0.24 0.00 0.00 7.82 C -0.08 -0.00 0.56
130 SD L20203 (AISC SECTIONS) 168 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.023 8 PASS LRFD-H1-1B-C 0.124 9
ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) 0.02 T 0.02 0.02 0.00 17.02 C 0.11 -0.03 0.00
131 SD L20203 (AISC SECTIONS) 169 SD L20203 (AISC SECTIONS)
MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ PASS LRFD-H1-1B-C 0.188 8 PASS LRFD-H1-1B-C 0.069 8
FX MY MZ LOCATION 5.08 C -0.32 0.00 0.00 0.05 C 0.06 0.05 0.00
======================================================================= 132 SD L20204 (AISC SECTIONS) 170 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.341 10 PASS LRFD-H1-1B-T 0.240 8
6.60 T -0.81 0.00 0.00 21.29 T -0.09 0.30 0.00
102 SD L20203 (AISC SECTIONS) DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 16 171 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.412 9 PASS LRFD-H1-1B-C 0.347 9
13.67 C 0.68 0.00 0.00 15.27 C 0.56 0.00 0.00
103 SD L20203 (AISC SECTIONS) 174 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.280 9 PASS LRFD-H1-1B-T 0.139 8
16.88 C 0.42 0.00 0.00 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) 1.57 T -0.13 -0.23 0.16
104 SD L20203 (AISC SECTIONS) 175 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.146 9 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ PASS LRFD-H1-1B-T 0.135 8
6.71 C 0.23 0.00 0.00 FX MY MZ LOCATION 5.01 T -0.08 0.11 0.00
105 SD L20203 (AISC SECTIONS) ======================================================================= 176 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.136 9 PASS LRFD-H1-1B-T 0.112 8
3.40 T 0.24 0.00 0.00 3.55 T 0.19 0.00 0.74
106 SD L20203 (AISC SECTIONS) 133 SD L20203 (AISC SECTIONS) DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 18
PASS LRFD-H1-1B-T 0.140 9 PASS LRFD-H1-1B-T 0.136 8
11.51 T -0.21 0.00 0.71 3.55 T -0.23 0.00 0.00
107 SD L20203 (AISC SECTIONS) 134 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.226 9 PASS LRFD-H1-1B-C 0.042 8
14.41 T 0.35 0.00 0.00 2.43 C -0.09 -0.00 0.50 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)
108 SD L20203 (AISC SECTIONS) 135 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.248 9 PASS LRFD-H1-1B-T 0.037 9 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/
5.23 T 0.43 0.00 0.00 1.54 T -0.02 0.03 0.00 FX MY MZ LOCATION
109 SD L20203 (AISC SECTIONS) 136 SD L20203 (AISC SECTIONS) =======================================================================
PASS LRFD-H1-1B-C 0.187 9 PASS LRFD-H1-1B-T 0.248 8
5.08 C 0.32 0.00 0.00 5.06 T -0.43 0.00 0.00
110 SD L20203 (AISC SECTIONS) 137 SD L20204 (AISC SECTIONS) 177 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.042 9 PASS LRFD-H1-1B-C 0.023 9 PASS LRFD-H1-1B-T 0.101 9
2.55 C 0.06 0.01 0.00 0.08 C 0.04 0.01 0.00 7.37 T 0.08 0.10 0.00
111 SD L20203 (AISC SECTIONS) 138 SD L20203 (AISC SECTIONS) 178 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.514 9 PASS LRFD-H1-1B-C 0.043 8 PASS LRFD-H1-1B-T 0.093 8
1.04 T 0.94 0.00 0.00 2.55 C -0.06 0.01 0.00 4.48 T -0.02 0.10 0.30
112 SD L20203 (AISC SECTIONS) 139 SD L20204 (AISC SECTIONS) 180 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.140 8 PASS LRFD-H1-1B-C 0.101 8 PASS LRFD-H1-1B-T 0.121 9
11.66 T 0.21 0.00 0.71 22.37 C 0.11 -0.02 0.00 19.41 T -0.10 0.03 0.00
113 SD L20203 (AISC SECTIONS) 147 SD L20203 (AISC SECTIONS) 181 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.196 8 PASS LRFD-H1-1B-T 0.095 8 PASS LRFD-H1-1B-C 0.323 9
7.64 T 0.08 0.19 0.65 12.54 T -0.12 -0.00 0.00 16.33 C 0.27 0.18 0.00
114 SD L20204 (AISC SECTIONS) 149 SD L20203 (AISC SECTIONS) 182 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.101 9 PASS LRFD-H1-1B-T 0.240 8 PASS LRFD-H1-1B-C 0.557 8
8.05 T 0.13 -0.09 0.61 15.40 T -0.36 0.01 0.00 24.57 C -0.88 0.00 0.00
115 SD L20203 (AISC SECTIONS) 150 SD L20204 (AISC SECTIONS) 183 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.427 9 PASS LRFD-H1-1B-C 0.321 7 PASS LRFD-H1-1B-C 0.398 7
11.96 T -0.73 0.00 1.12 6.32 C 0.00 0.55 0.00 28.64 C 0.00 0.61 0.00
116 SD L20203 (AISC SECTIONS) 151 SD L20203 (AISC SECTIONS) 184 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.258 8 PASS LRFD-H1-1B-T 0.105 8 PASS LRFD-H1-1B-C 0.158 9
0.63 T -0.01 0.35 0.90 3.40 T 0.16 0.02 1.15 7.04 C -0.23 -0.02 0.94
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 15 152 SD L20203 (AISC SECTIONS) 185 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.300 8 PASS LRFD-H1-1B-C 0.061 9
1.53 C -0.12 0.32 0.90 7.47 C 0.10 -0.01 0.29
155 SD L20203 (AISC SECTIONS) 187 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.096 9 PASS LRFD-H1-1B-C 0.275 9
ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) 8.91 C 0.06 0.05 0.00 11.97 C -0.18 0.20 0.37
156 SD L20203 (AISC SECTIONS) 188 SD L20204 (AISC SECTIONS)
MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ PASS LRFD-H1-1B-C 0.305 9 PASS LRFD-H1-1B-C 0.121 8
FX MY MZ LOCATION 17.97 C -0.08 0.30 0.73 30.03 C 0.14 -0.00 0.00
======================================================================= 157 SD L20204 (AISC SECTIONS) 189 SD L20203 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.211 9 PASS LRFD-H1-1B-T 0.145 11 B E A M N O. 13 D E S I G N R E S U L T S - SHEAR
1.07 C -0.10 0.21 0.50 4.26 T -0.00 0.25 0.41
191 SD L20204 (AISC SECTIONS) 236 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.361 7 PASS LRFD-H1-1B-T 0.173 8 AT START SUPPORT - Vu= 26.79 KNS Vc= 51.64 KNS Vs= 0.00 KNS
13.37 C 0.00 0.60 0.00 7.81 T 0.22 0.13 0.00 Tu= 0.92 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 9
192 SD L20204 (AISC SECTIONS) 237 SD L20204 (AISC SECTIONS) NO STIRRUPS ARE REQUIRED FOR TORSION.
PASS LRFD-H1-1B-C 0.059 9 PASS LRFD-H1-1B-T 0.174 9 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
0.29 C 0.09 0.04 0.00 8.24 T 0.22 0.13 0.19 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 738. MM
196 SD L20204 (AISC SECTIONS) 239 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.221 10 PASS LRFD-H1-1B-T 0.370 9 AT END SUPPORT - Vu= 23.24 KNS Vc= 52.09 KNS Vs= 0.00 KNS
1.13 C 0.01 0.39 0.00 8.89 T 0.28 0.43 0.19 Tu= 1.02 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
197 SD L20203 (AISC SECTIONS) 243 SD L20204 (AISC SECTIONS) NO STIRRUPS ARE REQUIRED FOR TORSION.
PASS LRFD-H1-1B-C 0.701 9 PASS LRFD-H1-1B-C 0.172 9 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
8.75 C 0.32 0.71 0.99 1.33 C 0.23 0.13 0.60 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 738. MM
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 19 244 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-C 0.175 8
1.77 C -0.23 0.14 0.60 ___ 2J____________________ 2150X 200X 400_____________________ 4J____
246 SD L20204 (AISC SECTIONS) | |
PASS LRFD-H1-1B-C 0.300 8 ||=========================================================================||
ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) 2.91 C -0.28 0.33 0.60 | 3No12 H|343. |0.TO 1408o12 H 343. 652.TO 2150 | | | | |
248 SD L20204 (AISC SECTIONS) | 6*12c/c172 | | | | | | | 6*12c/c172| |
MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ PASS LRFD-H1-1B-C 0.096 7 | 2No12 H| 57. |0.TO 2150 | | | | | | | |
FX MY MZ LOCATION 1.24 C -0.00 0.17 0.25 ||=========================================================================||
======================================================================= 249 SD L20204 (AISC SECTIONS) | |
PASS LRFD-H1-1B-C 0.193 9 |___________________________________________________________________________|
2.20 C -0.25 0.15 0.00 _______ _______ _______ _______ _______ _______ _______
198 SD L20203 (AISC SECTIONS) DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 21 | | | | | | | | | | | | | |
PASS LRFD-H1-1B-C 0.775 8 | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
7.05 C 1.38 0.00 1.27 | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
199 SD L20203 (AISC SECTIONS) | | | | | | | | | | | | | |
PASS LRFD-H1-1B-C 0.139 11 | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
2.95 C 0.24 0.00 0.00 ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) | oo | | oo | | oo | | oo | | oo | | oo | | oo |
200 SD L20204 (AISC SECTIONS) | | | | | | | | | | | | | |
PASS LRFD-H1-1B-C 0.064 10 MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ |_______| |_______| |_______| |_______| |_______| |_______| |_______|
0.44 C -0.00 0.11 0.00 FX MY MZ LOCATION DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 23
201 SD L20203 (AISC SECTIONS) =======================================================================
PASS LRFD-H1-1B-C 0.694 9
3.07 C -1.26 0.00 1.19
204 SD L20204 (AISC SECTIONS) 250 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.067 9 PASS LRFD-H1-1B-C 0.196 8 ACI 318-11 BEAM NO. 14 DESIGN RESULTS
2.41 T -0.11 0.03 0.50 3.63 C -0.27 0.15 0.35 =============================================
205 SD L20204 (AISC SECTIONS) 252 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.092 8 PASS LRFD-H1-1B-C 0.341 7 LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
6.87 T 0.14 0.04 0.00 6.88 C -0.00 0.59 0.35
207 SD L20204 (AISC SECTIONS) 254 SD L20204 (AISC SECTIONS) LEVEL HEIGHT BAR INFO FROM TO ANCHOR
PASS LRFD-H1-1B-T 0.093 9 PASS LRFD-H1-1B-T 0.111 11 (MM) (MM) (MM) STA END
6.87 T 0.14 0.04 0.10 3.14 T -0.00 0.19 0.46 _____________________________________________________________________
208 SD L20204 (AISC SECTIONS) 255 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.233 9 PASS LRFD-H1-1B-C 0.228 9
20.83 T 0.28 0.14 0.10 0.25 C -0.36 0.15 0.00 1 57. 3 - 12MM 475. 2050. NO YES
210 SD L20204 (AISC SECTIONS) 256 SD L20204 (AISC SECTIONS)
PASS LRFD-H1-1B-T 0.130 8 PASS LRFD-H1-1B-C 0.259 8 *** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED.
7.02 T 0.15 0.10 0.40 0.43 C -0.32 0.23 0.14 REQD. STEEL = 435. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2
211 SD L20204 (AISC SECTIONS) 258 SD L20204 (AISC SECTIONS) MAX NEG MOMENT = 50.15 KN-MET, LOADING 9
PASS LRFD-H1-1B-C 0.156 11 PASS LRFD-H1-1B-C 0.491 8
10.49 C 0.01 0.24 0.00 0.99 C -0.37 0.61 0.14
212 SD L20204 (AISC SECTIONS) 260 SD L20204 (AISC SECTIONS) ___ 4J____________________ 2050X 200X 400_____________________ 25J____
PASS LRFD-H1-1B-C 0.158 11 PASS LRFD-H1-1B-C 0.173 8 | |
10.78 C 0.01 0.24 0.20 0.27 C 0.27 -0.17 0.00 | |
214 SD L20204 (AISC SECTIONS) 262 SD L20204 (AISC SECTIONS) | |
PASS LRFD-H1-1B-T 0.250 7 PASS LRFD-H1-1B-C 0.217 9 | |
1.80 T -0.00 0.44 0.20 0.43 C -0.26 -0.30 0.00 | 3No12 H 57. 475.TO 2050 |
216 SD L20204 (AISC SECTIONS) 263 SD L20204 (AISC SECTIONS) | ==========================================================||
PASS LRFD-H1-1B-T 0.119 10 PASS LRFD-H1-1B-C 0.112 9 | |
18.20 T 0.00 0.15 0.00 0.10 C 0.23 -0.05 0.60 |___________________________________________________________________________|
217 SD L20204 (AISC SECTIONS) _______ _______ _______ _______ _______ _______ _______
PASS LRFD-H1-1B-C 0.136 8 | | | | | | | | | | | | | |
8.18 C -0.14 0.11 0.40 ************** END OF TABULATED RESULT OF DESIGN ************** | | | | | | | | | | | | | |
224 SD L20204 (AISC SECTIONS) | | | | | | | | | | | | | |
PASS LRFD-H1-1B-C 0.119 8 | | | | | | | | | | | | | |
16.96 C 0.12 -0.09 0.00 | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 20 210. START CONCRETE DESIGN | | | | | ooo | | ooo | | ooo | | ooo | | ooo |
211. CODE ACI | | | | | | | | | | | | | |
212. FC 20700 MEMB 1 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 154 160 - |_______| |_______| |_______| |_______| |_______| |_______| |_______|
213. 163 172 173 179 186 190 193 TO 195
214. FYMAIN 413688 MEMB 1 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 -
ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted) 215. 154 160 163 172 173 179 186 190 193 TO 195
216. MAXMAIN 16 MEMB 1 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 154 - ACI 318-11 BEAM NO. 15 DESIGN RESULTS
MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/ 217. 160 163 172 173 179 186 190 193 TO 195 =============================================
FX MY MZ LOCATION 218. DESIGN BEAM 13 TO 34 47 TO 63 73 76 81 84 87 90 93 96 121 140 TO 146 148 153 -
======================================================================= 219. 154 160 163 172 173 179 186 190 193 TO 195 LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 22
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
225 SD L20204 (AISC SECTIONS) (MM) (MM) (MM) STA END
PASS LRFD-H1-1B-C 0.118 9 _____________________________________________________________________
16.65 C -0.12 -0.09 0.00
227 SD L20204 (AISC SECTIONS) ACI 318-11 BEAM NO. 13 DESIGN RESULTS
PASS LRFD-H1-1B-C 0.210 8 ============================================= 1 57. 2 - 12MM 0. 2150. YES YES
24.45 C 0.13 -0.28 0.00 2 343. 3 - 12MM 0. 1408. YES NO
229 SD L20204 (AISC SECTIONS) LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 24
PASS LRFD-H1-1B-C 0.171 9
16.83 C 0.10 0.17 0.20 LEVEL HEIGHT BAR INFO FROM TO ANCHOR 3 343. 3 - 12MM 652. 2150. NO YES
230 SD L20204 (AISC SECTIONS) (MM) (MM) (MM) STA END
PASS LRFD-H1-1B-C 0.087 8 _____________________________________________________________________
3.09 C 0.08 0.09 0.00
231 SD L20204 (AISC SECTIONS) B E A M N O. 15 D E S I G N R E S U L T S - SHEAR
PASS LRFD-H1-1B-C 0.086 9 1 57. 2 - 12MM 0. 2150. YES YES
2.67 C 0.08 0.09 0.40 2 343. 3 - 12MM 0. 1408. YES NO
233 SD L20204 (AISC SECTIONS) 3 343. 3 - 12MM 652. 2150. NO YES AT START SUPPORT - Vu= 23.26 KNS Vc= 52.09 KNS Vs= 0.00 KNS
PASS LRFD-H1-1B-C 0.305 7 Tu= 1.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
13.92 C 0.00 0.50 0.40 NO STIRRUPS ARE REQUIRED FOR TORSION.
235 SD L20204 (AISC SECTIONS) REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 988. MM | 3No12 H 343.| 0.TO 1322| 3No12 H 343.1006.TO 2430| | | | |
| 7*12c/c172 | | | | | | | | 7*12c/c172 | |
AT END SUPPORT - Vu= 26.78 KNS Vc= 51.64 KNS Vs= 0.00 KNS | 2No12 H 57.| 0.TO 2430| | | | | | | | | |
Tu= 0.90 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 8 ___ 16J____________________ 2649X 200X 400_____________________ 18J____ ||=========================================================================||
NO STIRRUPS ARE REQUIRED FOR TORSION. | | | |
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. ||=========================================================================|| |___________________________________________________________________________|
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM | 3No12|H 343. 0.TO 1396 | |3No12 H 343.1144.TO 2650 | | | | | _______ _______ _______ _______ _______ _______ _______
| 7*12c/c172 | | | | | | | | 7*12c/c172 | | | | | | | | | | | | | | | |
| 2No12|H 57. 0.TO 2650 | | | | | | | | | | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
___ 6J____________________ 2150X 200X 400_____________________ 8J____ ||=========================================================================|| | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| | | | | | | | | | | | | | | | | |
||=========================================================================|| |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| 3No12 H|343. |0.TO 1408o12 H 343. 652.TO 2150 | | | | | _______ _______ _______ _______ _______ _______ _______ | oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 6*12c/c172 | | | | | | | 6*12c/c172| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| 2No12 H| 57. |0.TO 2150 | | | | | | | | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | |_______| |_______| |_______| |_______| |_______| |_______| |_______|
||=========================================================================|| | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| | | | | | | | | | | | | | | |
|___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
_______ _______ _______ _______ _______ _______ _______ | oo | | oo | | oo | | oo | | oo | | oo | | oo | ACI 318-11 BEAM NO. 20 DESIGN RESULTS
| | | | | | | | | | | | | | | | | | | | | | | | | | | | =============================================
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | |_______| |_______| |_______| |_______| |_______| |_______| |_______|
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | LEN - 2151. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | LEVEL HEIGHT BAR INFO FROM TO ANCHOR
| oo | | oo | | oo | | oo | | oo | | oo | | oo | ACI 318-11 BEAM NO. 18 DESIGN RESULTS (MM) (MM) (MM) STA END
| | | | | | | | | | | | | | ============================================= _____________________________________________________________________
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
1 57. 2 - 12MM 0. 2151. YES YES
LEVEL HEIGHT BAR INFO FROM TO ANCHOR 2 343. 3 - 12MM 0. 1409. YES NO
ACI 318-11 BEAM NO. 16 DESIGN RESULTS (MM) (MM) (MM) STA END 3 343. 3 - 12MM 653. 2151. NO YES
============================================= _____________________________________________________________________
LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
1 57. 3 - 12MM 278. 3891. NO NO B E A M N O. 20 D E S I G N R E S U L T S - SHEAR
LEVEL HEIGHT BAR INFO FROM TO ANCHOR 2 341. 2 - 16MM 0. 1408. YES NO
(MM) (MM) (MM) STA END
_____________________________________________________________________ *** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED. AT START SUPPORT - Vu= 30.16 KNS Vc= 51.52 KNS Vs= 0.00 KNS
REQD. STEEL = 447. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2 Tu= 0.15 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 9
MAX NEG MOMENT = 51.39 KN-MET, LOADING 11 NO STIRRUPS ARE REQUIRED FOR TORSION.
1 57. 3 - 12MM 278. 3891. NO NO REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
2 341. 2 - 16MM 0. 1408. YES NO DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 27 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 25
AT END SUPPORT - Vu= 21.70 KNS Vc= 52.17 KNS Vs= 0.00 KNS
___ 2J____________________ 4350X 200X 400_____________________ 12J____ Tu= 0.28 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
*** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED. | | NO STIRRUPS ARE REQUIRED FOR TORSION.
REQD. STEEL = 447. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2 ||======================= | REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
MAX NEG MOMENT = 51.40 KN-MET, LOADING 11 | 2No16 H 341. 0.TO 1408 | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM
| |
| 3No12 H 57. 278.TO 3891 | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 29
___ 8J____________________ 4350X 200X 400_____________________ 16J____ | ================================================================ |
| | | |
||======================= | |___________________________________________________________________________| ___ 20J____________________ 2150X 200X 400_____________________ 22J____
| 2No16 H 341. 0.TO 1408 | _______ _______ _______ _______ _______ _______ _______ | |
| | | | | | | | | | | | | | | | ||=========================================================================||
| 3No12 H 57. 278.TO 3891 | | oo | | oo | | | | | | | | | | | | 3No12 H|343. |0.TO 1409o12 H 343. 653.TO 2151 | | | | |
| ================================================================ | | 2#16 | | 2#16 | | | | | | | | | | | | 6*12c/c172 | | | | | | | 6*12c/c172| |
| | | | | | | | | | | | | | | | | 2No12 H| 57. |0.TO 2151 | | | | | | | |
|___________________________________________________________________________| | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | ||=========================================================================||
_______ _______ _______ _______ _______ _______ _______ | | | ooo | | ooo | | ooo | | ooo | | ooo | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | |___________________________________________________________________________|
| oo | | oo | | | | | | | | | | | |_______| |_______| |_______| |_______| |_______| |_______| |_______| _______ _______ _______ _______ _______ _______ _______
| 2#16 | | 2#16 | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | | ACI 318-11 BEAM NO. 19 DESIGN RESULTS | | | | | | | | | | | | | |
| | | | | | | | | | | | | | ============================================= | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
|_______| |_______| |_______| |_______| |_______| |_______| |_______| | oo | | oo | | oo | | oo | | oo | | oo | | oo |
LEN - 2430. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS | | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
ACI 318-11 BEAM NO. 17 DESIGN RESULTS (MM) (MM) (MM) STA END
============================================= _____________________________________________________________________
ACI 318-11 BEAM NO. 21 DESIGN RESULTS
LEN - 2650. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS =============================================
1 57. 2 - 12MM 0. 2430. YES YES
LEVEL HEIGHT BAR INFO FROM TO ANCHOR 2 343. 3 - 12MM 0. 1322. YES NO LEN - 2051. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
(MM) (MM) (MM) STA END 3 343. 3 - 12MM 1006. 2430. NO YES
_____________________________________________________________________ LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 57. 2 - 12MM 0. 2650. YES YES B E A M N O. 19 D E S I G N R E S U L T S - SHEAR
2 343. 3 - 12MM 0. 1396. YES NO
3 343. 3 - 12MM 1144. 2650. NO YES 1 57. 2 - 12MM 217. 2051. NO YES
AT START SUPPORT - Vu= 24.24 KNS Vc= 51.81 KNS Vs= 0.00 KNS 2 341. 2 - 16MM 0. 1538. YES NO
Tu= 0.33 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
NO STIRRUPS ARE REQUIRED FOR TORSION.
B E A M N O. 17 D E S I G N R E S U L T S - SHEAR REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 879. MM B E A M N O. 21 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 26.14 KNS Vc= 51.55 KNS Vs= 0.00 KNS AT END SUPPORT - Vu= 31.20 KNS Vc= 51.18 KNS Vs= 0.00 KNS
Tu= 0.30 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6 Tu= 0.33 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 11 AT START SUPPORT - Vu= 40.68 KNS Vc= 52.50 KNS Vs= 1.74 KNS
NO STIRRUPS ARE REQUIRED FOR TORSION. NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.02 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. NO STIRRUPS ARE REQUIRED FOR TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 988. MM PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 879. MM REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 689. MM
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 26 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 28
AT END SUPPORT - Vu= 9.01 KNS Vc= 50.05 KNS Vs= 0.00 KNS
AT END SUPPORT - Vu= 31.47 KNS Vc= 51.03 KNS Vs= 0.00 KNS Tu= 0.02 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
Tu= 0.30 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 11 ___ 12J____________________ 2430X 200X 400_____________________ 20J____ STIRRUPS ARE NOT REQUIRED.
NO STIRRUPS ARE REQUIRED FOR TORSION. | | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 30
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. ||=========================================================================||
AT END SUPPORT - Vu= 29.15 KNS Vc= 51.96 KNS Vs= 0.00 KNS
___ 22J____________________ 2050X 200X 400_____________________ 26J____ Tu= 0.16 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
| | NO STIRRUPS ARE REQUIRED FOR TORSION. AT START SUPPORT - Vu= 25.74 KNS Vc= 51.04 KNS Vs= 0.00 KNS
||======================================================= | REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. Tu= 0.96 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 11
| 2No16 H|341. |0.TO 1538 | | | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM NO STIRRUPS ARE REQUIRED FOR TORSION.
| 6*12c/c172 | | | | | REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
| 2No12 H| 57. 217.TO 2051 | | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 32 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 907. MM
| ===================================================================||
| | AT END SUPPORT - Vu= 24.45 KNS Vc= 52.09 KNS Vs= 0.00 KNS
|___________________________________________________________________________| ___ 6J____________________ 4350X 200X 400_____________________ 14J____ Tu= 1.21 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 7
_______ _______ _______ _______ _______ _______ _______ | | NO STIRRUPS ARE REQUIRED FOR TORSION.
| | | | | | | | | | | | | | ||========================== ===============================|| REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
| oo | | oo | | oo | | oo | | oo | | | | | | 3No12 H 343.| 0.TO 1600| 3No12|H 343.2569.TO 4350 | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 907. MM
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | | | 12*12c/c172 | | | | | | | | 12*12c/c172 |
| | | | | | | | | | | | | | | 2No12 H |57.| 0.TO 4003| | | | | | | | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 34
| | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | ||==================================================================== |
| | | oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | | |___________________________________________________________________________| ___ 22J____________________ 2486X 200X 400_____________________ 10J____
|_______| |_______| |_______| |_______| |_______| |_______| |_______| _______ _______ _______ _______ _______ _______ _______ | |
| | | | | | | | | | | | | | ||=========================================================================||
| ooo | | ooo | | ooo | | | | ooo | | ooo | | ooo | | 3No12 H 343.| 0.TO 15483No12 H 343.|834.TO 2486| | | | | |
| 3#12 | | 3#12 | | 3#12 | | | | 3#12 | | 3#12 | | 3#12 | | 7*12c/c172 | | | | | | | | 7*12c/c172 | |
ACI 318-11 BEAM NO. 22 DESIGN RESULTS | | | | | | | | | | | | | | | 2No12 H 57.| 0.TO 2486| | | | | | | | | |
============================================= | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | ||=========================================================================||
| oo | | oo | | oo | | oo | | oo | | oo | | | | |
LEN - 2151. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS | | | | | | | | | | | | | | |___________________________________________________________________________|
|_______| |_______| |_______| |_______| |_______| |_______| |_______| _______ _______ _______ _______ _______ _______ _______
LEVEL HEIGHT BAR INFO FROM TO ANCHOR | | | | | | | | | | | | | |
(MM) (MM) (MM) STA END | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
_____________________________________________________________________ | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
ACI 318-11 BEAM NO. 24 DESIGN RESULTS | | | | | | | | | | | | | |
============================================= | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
1 57. 2 - 12MM 0. 2151. YES YES | oo | | oo | | oo | | oo | | oo | | oo | | oo |
2 343. 3 - 12MM 0. 1409. YES NO LEN - 2594. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS | | | | | | | | | | | | | |
3 343. 3 - 12MM 832. 2151. NO YES |_______| |_______| |_______| |_______| |_______| |_______| |_______|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
B E A M N O. 22 D E S I G N R E S U L T S - SHEAR ACI 318-11 BEAM NO. 26 DESIGN RESULTS
=============================================
1 57. 2 - 12MM 0. 2594. YES YES
AT START SUPPORT - Vu= 22.15 KNS Vc= 52.17 KNS Vs= 0.00 KNS 2 343. 3 - 12MM 0. 1593. YES NO LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
Tu= 0.43 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6 3 343. 3 - 12MM 892. 2594. NO YES
NO STIRRUPS ARE REQUIRED FOR TORSION. LEVEL HEIGHT BAR INFO FROM TO ANCHOR
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. (MM) (MM) (MM) STA END
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM _____________________________________________________________________
B E A M N O. 24 D E S I G N R E S U L T S - SHEAR
AT END SUPPORT - Vu= 30.25 KNS Vc= 51.53 KNS Vs= 0.00 KNS
Tu= 0.40 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 8 1 57. 2 - 12MM 165. 4350. NO YES
NO STIRRUPS ARE REQUIRED FOR TORSION. AT START SUPPORT - Vu= 31.24 KNS Vc= 50.91 KNS Vs= 0.00 KNS 2 343. 3 - 12MM 0. 1600. YES NO
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. Tu= 1.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 10 3 343. 3 - 12MM 2569. 4350. NO YES
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 31 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 960. MM
B E A M N O. 26 D E S I G N R E S U L T S - SHEAR
AT END SUPPORT - Vu= 23.10 KNS Vc= 50.90 KNS Vs= 0.00 KNS
___ 24J____________________ 2150X 200X 400_____________________ 18J____ Tu= 0.88 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 11
| | NO STIRRUPS ARE REQUIRED FOR TORSION. AT START SUPPORT - Vu= 29.13 KNS Vc= 51.98 KNS Vs= 0.00 KNS
||=========================================================================|| REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. Tu= 0.17 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
| 3No12 H|343. |0.TO 1409 3No12 H|343. 832.TO 2151 | | | | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 960. MM NO STIRRUPS ARE REQUIRED FOR TORSION.
| 6*12c/c172 | | | | | | | 6*12c/c172| | REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
| 2No12 H| 57. |0.TO 2151 | | | | | | | | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 33 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM
||=========================================================================||
| | AT END SUPPORT - Vu= 27.06 KNS Vc= 52.67 KNS Vs= 0.00 KNS
|___________________________________________________________________________| ___ 14J____________________ 2593X 200X 400_____________________ 24J____ Tu= 0.17 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
_______ _______ _______ _______ _______ _______ _______ | | NO STIRRUPS ARE REQUIRED FOR TORSION.
| | | | | | | | | | | | | | ||=========================================================================|| REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | 3No12 H 343.| 0.TO 1593|3No12|H 343. 892.TO 2594 | | | | | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 7*12c/c172 | | | | | | | | 7*12c/c172 | |
| | | | | | | | | | | | | | | 2No12 H 57.| 0.TO 2594| | | | | | | | | | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 35
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | ||=========================================================================||
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | | |___________________________________________________________________________| ___ 10J____________________ 4350X 200X 400_____________________ 4J____
|_______| |_______| |_______| |_______| |_______| |_______| |_______| _______ _______ _______ _______ _______ _______ _______ | |
| | | | | | | | | | | | | | ||========================== ===============================||
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | 3No12 H 343.| 0.TO 1600| 3No12|H 343.2569.TO 4350 | | |
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 12*12c/c172 | | | | | | | | 12*12c/c172 | |
ACI 318-11 BEAM NO. 23 DESIGN RESULTS | | | | | | | | | | | | | | | |2No12 H| 57. 165.TO|4350 | | | | | | | | |
============================================= | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | =========================================================================||
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | |
LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS | | | | | | | | | | | | | | |___________________________________________________________________________|
|_______| |_______| |_______| |_______| |_______| |_______| |_______| _______ _______ _______ _______ _______ _______ _______
LEVEL HEIGHT BAR INFO FROM TO ANCHOR | | | | | | | | | | | | | |
(MM) (MM) (MM) STA END | ooo | | ooo | | ooo | | | | ooo | | ooo | | ooo |
_____________________________________________________________________ | 3#12 | | 3#12 | | 3#12 | | | | 3#12 | | 3#12 | | 3#12 |
ACI 318-11 BEAM NO. 25 DESIGN RESULTS | | | | | | | | | | | | | |
============================================= | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
1 57. 2 - 12MM 0. 4003. YES NO | | | oo | | oo | | oo | | oo | | oo | | oo |
2 343. 3 - 12MM 0. 1600. YES NO LEN - 2486. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS | | | | | | | | | | | | | |
3 343. 3 - 12MM 2569. 4350. NO YES |_______| |_______| |_______| |_______| |_______| |_______| |_______|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
B E A M N O. 23 D E S I G N R E S U L T S - SHEAR ACI 318-11 BEAM NO. 27 DESIGN RESULTS
=============================================
1 57. 2 - 12MM 0. 2486. YES YES
AT START SUPPORT - Vu= 27.03 KNS Vc= 52.66 KNS Vs= 0.00 KNS 2 343. 3 - 12MM 0. 1548. YES NO LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
Tu= 0.16 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6 3 343. 3 - 12MM 834. 2486. NO YES
NO STIRRUPS ARE REQUIRED FOR TORSION. LEVEL HEIGHT BAR INFO FROM TO ANCHOR
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. (MM) (MM) (MM) STA END
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM _____________________________________________________________________
B E A M N O. 25 D E S I G N R E S U L T S - SHEAR
Tu= 0.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
1 57. 2 - 12MM 0. 2150. YES YES AT START SUPPORT - Vu= 20.37 KNS Vc= 51.72 KNS Vs= 0.00 KNS NO STIRRUPS ARE REQUIRED FOR TORSION.
2 343. 3 - 12MM 0. 2150. YES YES Tu= 0.19 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 7 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
NO STIRRUPS ARE REQUIRED FOR TORSION. PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 40
B E A M N O. 27 D E S I G N R E S U L T S - SHEAR
AT END SUPPORT - Vu= 20.57 KNS Vc= 51.48 KNS Vs= 0.00 KNS
Tu= 0.06 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 8 ___ 25J____________________ 4350X 200X 400_____________________ 27J____
AT START SUPPORT - Vu= 20.29 KNS Vc= 51.46 KNS Vs= 0.00 KNS NO STIRRUPS ARE REQUIRED FOR TORSION. | |
Tu= 0.23 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 9 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. | ========================||
NO STIRRUPS ARE REQUIRED FOR TORSION. PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 739. MM | 3No12 H|343.2931.TO 4350 |
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. | 12*12c/c172 | | 12*12c/c172 |
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 738. MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 38 | 3No12 H 57. 0.TO 3562 | | | |
||============================================================= |
AT END SUPPORT - Vu= 19.94 KNS Vc= 51.70 KNS Vs= 0.00 KNS | |
Tu= 0.14 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 7 ___ 14J____________________ 2150X 200X 400_____________________ 16J____ |___________________________________________________________________________|
NO STIRRUPS ARE REQUIRED FOR TORSION. | | _______ _______ _______ _______ _______ _______ _______
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. ||=========================================================================|| | | | | | | | | | | | | | |
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 738. MM | 3No12 H|343. |0.TO 2150 | | | | | | | | | | | | | | | | | | | ooo | | ooo |
| 6*12c/c172 | | | | | | | 6*12c/c172| | | | | | | | | | | | | 3#12 | | 3#12 |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 36 | 2No12 H| 57. |0.TO 2150 | | | | | | | | | | | | | | | | | | | | | |
||=========================================================================|| | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | | | |
___ 12J____________________ 2150X 200X 400_____________________ 10J____ |___________________________________________________________________________| | | | | | | | | | | | | | |
| | _______ _______ _______ _______ _______ _______ _______ |_______| |_______| |_______| |_______| |_______| |_______| |_______|
||=========================================================================|| | | | | | | | | | | | | | |
| 3No12 H|343. |0.TO 2150 | | | | | | | | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 6*12c/c172 | | | | | | | 6*12c/c172| | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| 2No12 H| 57. |0.TO 2150 | | | | | | | | | | | | | | | | | | | | | | ACI 318-11 BEAM NO. 32 DESIGN RESULTS
||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| | | oo | | oo | | oo | | oo | | oo | | oo | | oo |
|___________________________________________________________________________| | | | | | | | | | | | | | | LEN - 2051. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
_______ _______ _______ _______ _______ _______ _______ |_______| |_______| |_______| |_______| |_______| |_______| |_______|
| | | | | | | | | | | | | | LEVEL HEIGHT BAR INFO FROM TO ANCHOR
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | (MM) (MM) (MM) STA END
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | _____________________________________________________________________
| | | | | | | | | | | | | | ACI 318-11 BEAM NO. 30 DESIGN RESULTS
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| oo | | oo | | oo | | oo | | oo | | oo | | oo | 1 57. 2 - 12MM 0. 1748. YES NO
| | | | | | | | | | | | | | LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS 2 341. 2 - 16MM 427. 2051. NO YES
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________ B E A M N O. 32 D E S I G N R E S U L T S - SHEAR
ACI 318-11 BEAM NO. 28 DESIGN RESULTS
=============================================
1 57. 3 - 12MM 0. 1489. YES NO AT START SUPPORT - Vu= 8.86 KNS Vc= 50.03 KNS Vs= 0.00 KNS
LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS Tu= 0.02 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
*** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED. STIRRUPS ARE NOT REQUIRED.
LEVEL HEIGHT BAR INFO FROM TO ANCHOR REQD. STEEL = 435. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2 AT END SUPPORT - Vu= 40.69 KNS Vc= 52.48 KNS Vs= 1.77 KNS
(MM) (MM) (MM) STA END MAX NEG MOMENT = 50.15 KN-MET, LOADING 8 Tu= 0.02 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6
_____________________________________________________________________ NO STIRRUPS ARE REQUIRED FOR TORSION.
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 39 REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 689. MM
1 59. 2 - 16MM 270. 2050. NO YES
___ 25J____________________ 2049X 200X 400_____________________ 6J____ DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 41
*** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED. | |
REQD. STEEL = 481. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2 | |
MAX NEG MOMENT = 54.90 KN-MET, LOADING 9 | | ___ 26J____________________ 2050X 200X 400_____________________ 24J____
| | | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 37 | 3No12 H 57. 0.TO 1489 | | ============================================================||
||====================================================== | | 2No16 H 341. 427.TO 2051 | | | |
| | | | | 6*12c/c172 |
___ 10J____________________ 2050X 200X 400_____________________ 27J____ |___________________________________________________________________________| | 2No12 H 57. 0.TO 1748 | | | |
| | _______ _______ _______ _______ _______ _______ _______ ||=============================================================== |
| | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | |___________________________________________________________________________|
| | | | | | | | | | | | | | | | _______ _______ _______ _______ _______ _______ _______
| 2No16 H 59. 270.TO 2050 | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| =================================================================|| | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | | | | | oo | | oo | | oo | | oo | | oo |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | | | | | | | | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
|___________________________________________________________________________| | | | | | | | | | | | | | | | | | | | | | | | | | | | |
_______ _______ _______ _______ _______ _______ _______ |_______| |_______| |_______| |_______| |_______| |_______| |_______| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | |
| | | | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |_______| |_______| |_______| |_______| |_______| |_______| |_______|
| | | | | | | | | | | | | | ACI 318-11 BEAM NO. 31 DESIGN RESULTS
| | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | =============================================
| | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | | LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS ACI 318-11 BEAM NO. 33 DESIGN RESULTS
|_______| |_______| |_______| |_______| |_______| |_______| |_______| =============================================
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS
_____________________________________________________________________
ACI 318-11 BEAM NO. 29 DESIGN RESULTS LEVEL HEIGHT BAR INFO FROM TO ANCHOR
============================================= (MM) (MM) (MM) STA END
1 57. 3 - 12MM 0. 3562. YES NO _____________________________________________________________________
LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS 2 343. 3 - 12MM 2931. 4350. NO YES
LEVEL HEIGHT BAR INFO FROM TO ANCHOR 1 59. 2 - 16MM 0. 1695. YES NO
(MM) (MM) (MM) STA END
_____________________________________________________________________ B E A M N O. 31 D E S I G N R E S U L T S - SHEAR *** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED.
REQD. STEEL = 482. MM2, MAX. STEEL PERMISSIBLE = 1075. MM2
MAX NEG MOMENT = 55.03 KN-MET, LOADING 8
1 57. 2 - 12MM 0. 2150. YES YES AT START SUPPORT - Vu= 21.60 KNS Vc= 53.70 KNS Vs= 0.00 KNS
2 343. 3 - 12MM 0. 2150. YES YES Tu= 0.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 42
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 1838. MM ___ 27J____________________ 2049X 200X 400_____________________ 14J____
B E A M N O. 29 D E S I G N R E S U L T S - SHEAR | |
AT END SUPPORT - Vu= 33.89 KNS Vc= 52.83 KNS Vs= 0.00 KNS | |
| | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 44 STIRRUPS ARE NOT REQUIRED.
| | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 46
| 2No16 H 59. 0.TO 1695 |
||============================================================= | ___ 37J____________________ 2150X 200X 300_____________________ 34J____
| | | | ___ 33J____________________ 2150X 200X 300_____________________
38J____
|___________________________________________________________________________| ||=========================================================================|| | |
_______ _______ _______ _______ _______ _______ _______ | 2No12 H 243.| 0.TO 2150| | | | | | | | | | | | | | | ||=========================================================================||
| | | | | | | | | | | | | | | 12*12c/c 81 | | | | | | | | | | | | | 12*12c/c 81 | | | 2No12 H 243. 0.TO 2150 |
| | | | | | | | | | | | | | | 2No12 H 57.| 0.TO 1083| | | | 2No12 H| 57.1298.TO|2150 | | | | |
| | | | | | | | | | | | | | ||===================================== ==============================|| | 2No12 H 57. 0.TO 763 2No12 H 57. 978.TO 2150 |
| | | | | | | | | | | | | | | | ||========================= =========================================||
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | | |___________________________________________________________________________| | |
| oo | | oo | | oo | | oo | | oo | | | | | _________ _________ _________ _________ _________ _________ |___________________________________________________________________________|
| | | | | | | | | | | | | | | | | | | | | | | | | | _________ _________ _________ _________ _________ _________
|_______| |_______| |_______| |_______| |_______| |_______| |_______| | oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| 2#12 | | 2#12 | | 2#12 | | | | 2#12 | | 2#12 | | | | | | | | | | | | |
ACI 318-11 BEAM NO. 34 DESIGN RESULTS | oo | | oo | | oo | | | | oo | | oo | | 2#12 | | 2#12 | | | | 2#12 | | 2#12 | | 2#12 |
============================================= | | | | | | | | | | | | | oo | | oo | | | | oo | | oo | | oo |
|_________| |_________| |_________| |_________| |_________| |_________| | | | | | | | | | | | |
LEN - 2540. MM FY - 414. FC - 21. MPA, SIZE - 200. X 400. MMS |_________| |_________| |_________| |_________| |_________| |_________|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END ACI 318-11 BEAM NO. 48 DESIGN RESULTS
_____________________________________________________________________ ============================================= ACI 318-11 BEAM NO. 50 DESIGN RESULTS
=============================================
LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
1 57. 2 - 12MM 1105. 2387. NO NO LEN - 350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
2 343. 3 - 12MM 0. 1782. YES NO LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END LEVEL HEIGHT BAR INFO FROM TO ANCHOR
_____________________________________________________________________ (MM) (MM) (MM) STA END
_____________________________________________________________________
B E A M N O. 34 D E S I G N R E S U L T S - SHEAR
1 57. 3 - 12MM 473. 2050. NO YES
2 243. 3 - 12MM 0. 1419. YES NO 1 57. 2 - 12MM 0. 350. YES YES
AT START SUPPORT - Vu= 21.29 KNS Vc= 49.67 KNS Vs= 0.00 KNS 2 243. 2 - 12MM 0. 350. YES YES
Tu= 0.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 7
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. B E A M N O. 48 D E S I G N R E S U L T S - SHEAR
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 172. MM C/C FOR 934. MM B E A M N O. 50 D E S I G N R E S U L T S - SHEAR
AT END SUPPORT - Vu= 3.25 KNS Vc= 49.83 KNS Vs= 0.00 KNS AT START SUPPORT - Vu= 19.65 KNS Vc= 36.73 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 6 Tu= 0.20 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED. NO STIRRUPS ARE REQUIRED FOR TORSION. ** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 50 IS BEYOND
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 43 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM
___ 27J____________________ 2540X 200X 400_____________________ 26J____ AT END SUPPORT - Vu= 16.53 KNS Vc= 36.27 KNS Vs= 0.00 KNS ** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 50 IS BEYOND
| | Tu= 0.20 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
||==================================================== | NO STIRRUPS ARE REQUIRED FOR TORSION.
| 3No12 H 343. 0.TO 1782 | | REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 47
| 7*12c/c172 | | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM
| 2No12 H 57.1105.TO 2387 |
| ======================================= | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 45 ___ 37J____________________ 350X 200X 300_____________________ 41J____
| | | |
|___________________________________________________________________________| ||=========================================================================||
_______ _______ _______ _______ _______ _______ _______ ___ 34J____________________ 2050X 200X 300_____________________ 40J____ | 2No12 H 243. 0.TO 350 |
| | | | | | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | | | | ||=================================================== | | 2No12 H 57. 0.TO 350 |
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | 3No12 H 243. 0.TO 1419 | | | | | | | ||=========================================================================||
| | | | | | | | | | | | | | | 8*12c/c122 | | | | | | | | 8*12c/c122 | | |
| | | | | | | 2#12 | | 2#12 | | 2#12 | | | | |3No12 H 57. 473.TO|2050| | | | |___________________________________________________________________________|
| | | | | | | oo | | oo | | oo | | | | ==========================================================|| _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | | | | | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______| |___________________________________________________________________________| | oo | | oo | | oo | | oo | | oo | | oo |
_________ _________ _________ _________ _________ _________ | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
ACI 318-11 BEAM NO. 47 DESIGN RESULTS | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | oo | | oo | | oo | | oo | | oo | | oo |
============================================= | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | |_________| |_________| |_________| |_________| |_________| |_________|
LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS | | | | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | |
LEVEL HEIGHT BAR INFO FROM TO ANCHOR |_________| |_________| |_________| |_________| |_________| |_________|
(MM) (MM) (MM) STA END ACI 318-11 BEAM NO. 51 DESIGN RESULTS
_____________________________________________________________________ =============================================
ACI 318-11 BEAM NO. 49 DESIGN RESULTS LEN - 850. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
1 57. 2 - 12MM 0. 1083. YES NO =============================================
2 57. 2 - 12MM 1298. 2150. NO YES LEVEL HEIGHT BAR INFO FROM TO ANCHOR
3 243. 2 - 12MM 0. 2150. YES YES LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS (MM) (MM) (MM) STA END
_____________________________________________________________________
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
B E A M N O. 47 D E S I G N R E S U L T S - SHEAR _____________________________________________________________________ 1 57. 2 - 12MM 0. 850. YES YES
2 243. 2 - 12MM 0. 850. YES YES
AT START SUPPORT - Vu= 0.74 KNS Vc= 35.23 KNS Vs= 0.00 KNS 1 57. 2 - 12MM 0. 763. YES NO
Tu= 1.02 KN-MET Tc= 1.0 KN-MET Ts= 1.4 KN-MET LOAD 10 2 57. 2 - 12MM 978. 2150. NO YES
STIRRUPS ARE REQUIRED FOR TORSION. 3 243. 2 - 12MM 0. 2150. YES YES B E A M N O. 51 D E S I G N R E S U L T S - SHEAR
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 81. MM C/C FOR 838. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.53 SQ.CM. AT START SUPPORT - Vu= 2.46 KNS Vc= 66.04 KNS Vs= 0.00 KNS
B E A M N O. 49 D E S I G N R E S U L T S - SHEAR Tu= 0.26 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
AT END SUPPORT - Vu= 4.06 KNS Vc= 35.14 KNS Vs= 0.00 KNS STIRRUPS ARE NOT REQUIRED.
Tu= 1.02 KN-MET Tc= 1.0 KN-MET Ts= 1.4 KN-MET LOAD 10 AT END SUPPORT - Vu= 0.13 KNS Vc= 66.04 KNS Vs= 0.00 KNS
STIRRUPS ARE REQUIRED FOR TORSION. AT START SUPPORT - Vu= 3.98 KNS Vc= 35.53 KNS Vs= 0.00 KNS Tu= 0.26 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. Tu= 0.17 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 81. MM C/C FOR 838. MM STIRRUPS ARE NOT REQUIRED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 48
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.53 SQ.CM. AT END SUPPORT - Vu= 0.66 KNS Vc= 35.92 KNS Vs= 0.00 KNS
Tu= 0.17 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
___ 36J____________________ 850X 200X 300_____________________ 42J____ Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 8 AT END SUPPORT - Vu= 3.90 KNS Vc= 35.37 KNS Vs= 0.00 KNS
| | NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
||=========================================================================|| REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. STIRRUPS ARE NOT REQUIRED.
| 2No12 H 243. 0.TO 850 | PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 839. MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 52
| |
| 2No12 H 57. 0.TO 850 | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 50
||=========================================================================|| ___ 34J____________________ 4350X 200X 300_____________________ 35J____
| | | |
|___________________________________________________________________________| ___ 29J____________________ 2150X 200X 300_____________________ 30J____ ||=============================== ===================================||
_________ _________ _________ _________ _________ _________ | | | 2No12 H 243. 0.TO 1844 2No12 H 243.2325.TO 4350 |
| | | | | | | | | | | | ||=========================================================================|| | |
| oo | | oo | | oo | | oo | | oo | | oo | | 2No12|H 243. 0.TO 1290 |2No12 H 243. 771.TO|2151| | | | | | | 2No12 H 57. 0.TO 4350 |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 8*12c/c122 | | | | | | | | | 8*12c/c122| | ||=========================================================================||
| | | | | | | | | | | | | 2No12 H |57. 109.TO 2151 | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | ========================================================================|| |___________________________________________________________________________|
| oo | | oo | | oo | | oo | | oo | | oo | | | _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | |___________________________________________________________________________| | | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| _________ _________ _________ _________ _________ _________ | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
ACI 318-11 BEAM NO. 52 DESIGN RESULTS | | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo |
============================================= | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | |
| | | oo | | oo | | oo | | oo | | oo | |_________| |_________| |_________| |_________| |_________| |_________|
LEN - 2151. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS | | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END ACI 318-11 BEAM NO. 56 DESIGN RESULTS
_____________________________________________________________________ =============================================
ACI 318-11 BEAM NO. 54 DESIGN RESULTS
============================================= LEN - 2486. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
1 57. 2 - 12MM 0. 1954. YES NO
2 243. 2 - 12MM 0. 1290. YES NO LEN - 2051. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS LEVEL HEIGHT BAR INFO FROM TO ANCHOR
3 243. 2 - 12MM 771. 2151. NO YES (MM) (MM) (MM) STA END
LEVEL HEIGHT BAR INFO FROM TO ANCHOR _____________________________________________________________________
(MM) (MM) (MM) STA END
_____________________________________________________________________
B E A M N O. 52 D E S I G N R E S U L T S - SHEAR 1 57. 2 - 12MM 0. 2486. YES YES
2 243. 2 - 12MM 0. 1430. YES NO
1 57. 2 - 12MM 400. 2051. NO YES 3 243. 2 - 12MM 953. 2486. NO YES
AT START SUPPORT - Vu= 13.99 KNS Vc= 35.82 KNS Vs= 0.00 KNS 2 243. 3 - 12MM 0. 1249. YES NO
Tu= 0.05 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 9
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. B E A M N O. 56 D E S I G N R E S U L T S - SHEAR
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 839. MM B E A M N O. 54 D E S I G N R E S U L T S - SHEAR
AT END SUPPORT - Vu= 20.40 KNS Vc= 35.72 KNS Vs= 0.00 KNS AT START SUPPORT - Vu= 1.45 KNS Vc= 46.22 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 8 AT START SUPPORT - Vu= 29.13 KNS Vc= 36.77 KNS Vs= 2.07 KNS Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.07 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. NO STIRRUPS ARE REQUIRED FOR TORSION. AT END SUPPORT - Vu= 2.54 KNS Vc= 36.50 KNS Vs= 0.00 KNS
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 839. MM REINFORCEMENT IS REQUIRED FOR SHEAR. Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM STIRRUPS ARE NOT REQUIRED.
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 49 DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 53
AT END SUPPORT - Vu= 10.55 KNS Vc= 35.67 KNS Vs= 0.00 KNS
Tu= 0.07 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
___ 28J____________________ 2150X 200X 300_____________________ 32J____ STIRRUPS ARE NOT REQUIRED. ___ 35J____________________ 2486X 200X 300_____________________
32J____
| | DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 51 | |
||=========================================================================|| ||=========================================================================||
| 2No12|H 243. 0.TO 1290 |2No12 H 243. 771.TO|2151| | | | | | 2No12 H 243. 0.TO 1430 2No12 H 243. 953.TO 2486 |
| 8*12c/c122 | | | | | | | | | 8*12c/c122 | ___ 32J____________________ 2050X 200X 300_____________________ 43J____ | |
| 2No12|H 57. 0.TO 1954 | | | | | | | | | | | | | 2No12 H 57. 0.TO 2486 |
||==================================================================== | ||============================================= | ||=========================================================================||
| | | 3No12 H 243. 0.TO 1249 | | | | | |
|___________________________________________________________________________| | 8*12c/c122 | | | | | | |___________________________________________________________________________|
_________ _________ _________ _________ _________ _________ | 2No12 H| 57.|400.TO 2051 | _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | | =============================================================|| | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | _________ _________ _________ _________ _________ _________ | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | | | ooo | | ooo | | ooo | | ooo | | | | | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| | | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
| | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
ACI 318-11 BEAM NO. 53 DESIGN RESULTS |_________| |_________| |_________| |_________| |_________| |_________| ACI 318-11 BEAM NO. 57 DESIGN RESULTS
============================================= =============================================
LEN - 2151. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
ACI 318-11 BEAM NO. 55 DESIGN RESULTS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR ============================================= LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END (MM) (MM) (MM) STA END
_____________________________________________________________________ LEN - 4350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS _____________________________________________________________________
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
1 57. 2 - 12MM 109. 2151. NO YES (MM) (MM) (MM) STA END 1 57. 2 - 12MM 0. 4350. YES YES
2 243. 2 - 12MM 0. 1290. YES NO _____________________________________________________________________ 2 243. 2 - 12MM 0. 1844. YES NO
3 243. 2 - 12MM 771. 2151. NO YES 3 243. 2 - 12MM 2325. 4350. NO YES
1 57. 2 - 12MM 0. 4350. YES YES
2 243. 2 - 12MM 0. 1844. YES NO
B E A M N O. 53 D E S I G N R E S U L T S - SHEAR 3 243. 2 - 12MM 2325. 4350. NO YES B E A M N O. 57 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 20.36 KNS Vc= 35.71 KNS Vs= 0.00 KNS AT START SUPPORT - Vu= 3.76 KNS Vc= 35.41 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 9 B E A M N O. 55 D E S I G N R E S U L T S - SHEAR Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
NO STIRRUPS ARE REQUIRED FOR TORSION. STIRRUPS ARE NOT REQUIRED.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. AT END SUPPORT - Vu= 3.91 KNS Vc= 35.37 KNS Vs= 0.00 KNS
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 839. MM AT START SUPPORT - Vu= 3.77 KNS Vc= 35.41 KNS Vs= 0.00 KNS Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 13.92 KNS Vc= 35.82 KNS Vs= 0.00 KNS STIRRUPS ARE NOT REQUIRED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 54
||=========================================================================|| | |
| 2No12 H 243. 0.TO 2150 | ||=========================================================================||
___ 33J____________________ 4350X 200X 300_____________________ 31J____ | | | 2No12 H 243. 0.TO 2150 |
| | | 2No12 H 57. 0.TO 1130 2No12 H 57.1287.TO 2150 | | |
||=============================== ===================================|| ||====================================== ==============================|| | 2No12 H 57. 0.TO 774 2No12 H 57. 930.TO 2150 |
| 2No12 H 243. 0.TO 1844 2No12 H 243.2325.TO 4350 | | | ||========================== ===========================================||
| | |___________________________________________________________________________| | |
| 2No12 H 57. 0.TO 4350 | _________ _________ _________ _________ _________ _________ |___________________________________________________________________________|
||=========================================================================|| | | | | | | | | | | | | _________ _________ _________ _________ _________ _________
| | | oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
|___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | oo | | oo | | oo | | oo | | oo | | oo |
_________ _________ _________ _________ _________ _________ | | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | 2#12 | | 2#12 | | | | 2#12 | | 2#12 | | 2#12 |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | oo | | oo | | | | oo | | oo | | oo |
| | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________| | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | |_________| |_________| |_________| |_________| |_________| |_________|
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| ACI 318-11 BEAM NO. 60 DESIGN RESULTS
============================================= ACI 318-11 BEAM NO. 62 DESIGN RESULTS
=============================================
LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
ACI 318-11 BEAM NO. 58 DESIGN RESULTS LEN - 350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
============================================= LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END LEVEL HEIGHT BAR INFO FROM TO ANCHOR
LEN - 2594. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS _____________________________________________________________________ (MM) (MM) (MM) STA END
_____________________________________________________________________
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END 1 57. 3 - 12MM 451. 2050. NO YES
_____________________________________________________________________ 2 243. 3 - 12MM 0. 1419. YES NO 1 57. 2 - 12MM 0. 350. YES YES
2 243. 2 - 12MM 0. 350. YES YES
1 57. 2 - 12MM 0. 2594. YES YES
2 243. 2 - 12MM 0. 1475. YES NO B E A M N O. 60 D E S I G N R E S U L T S - SHEAR
3 243. 2 - 12MM 1011. 2594. NO YES B E A M N O. 62 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 22.13 KNS Vc= 36.83 KNS Vs= 0.00 KNS
Tu= 0.05 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
B E A M N O. 58 D E S I G N R E S U L T S - SHEAR NO STIRRUPS ARE REQUIRED FOR TORSION. ** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 62 IS BEYOND
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM
AT START SUPPORT - Vu= 1.67 KNS Vc= 64.66 KNS Vs= 0.00 KNS
Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 AT END SUPPORT - Vu= 19.00 KNS Vc= 36.37 KNS Vs= 0.00 KNS ** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 62 IS BEYOND
STIRRUPS ARE NOT REQUIRED. Tu= 0.05 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
AT END SUPPORT - Vu= 2.53 KNS Vc= 36.58 KNS Vs= 0.00 KNS NO STIRRUPS ARE REQUIRED FOR TORSION.
Tu= 0.07 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 59
STIRRUPS ARE NOT REQUIRED. PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 55
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 57 ___ 38J____________________ 350X 200X 300_____________________ 45J____
| |
___ 31J____________________ 2593X 200X 300_____________________ 29J____ ||=========================================================================||
| | ___ 35J____________________ 2050X 200X 300_____________________ 44J____ | 2No12 H 243. 0.TO 350 |
||=========================================================================|| | | | |
| 2No12 H 243. 0.TO 1475 2No12 H 243.1011.TO 2594 | ||=================================================== | | 2No12 H 57. 0.TO 350 |
| | | 3No12 H 243. 0.TO 1419 | | | | | | | ||=========================================================================||
| 2No12 H 57. 0.TO 2594 | | 8*12c/c122 | | | | | | | | 8*12c/c122 | | |
||=========================================================================|| | 3No12|H 57. 451.TO 2050 | | | | |___________________________________________________________________________|
| | | ===========================================================|| _________ _________ _________ _________ _________ _________
|___________________________________________________________________________| | | | | | | | | | | | | | |
_________ _________ _________ _________ _________ _________ |___________________________________________________________________________| | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | _________ _________ _________ _________ _________ _________ | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | ooo | | ooo | | ooo | | ooo | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | | | | | | ooo | | ooo | | ooo | | ooo |
|_________| |_________| |_________| |_________| |_________| |_________| | | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|
ACI 318-11 BEAM NO. 63 DESIGN RESULTS
=============================================
ACI 318-11 BEAM NO. 59 DESIGN RESULTS
============================================= ACI 318-11 BEAM NO. 61 DESIGN RESULTS LEN - 850. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
=============================================
LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS LEVEL HEIGHT BAR INFO FROM TO ANCHOR
LEN - 2150. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS (MM) (MM) (MM) STA END
LEVEL HEIGHT BAR INFO FROM TO ANCHOR _____________________________________________________________________
(MM) (MM) (MM) STA END LEVEL HEIGHT BAR INFO FROM TO ANCHOR
_____________________________________________________________________ (MM) (MM) (MM) STA END
_____________________________________________________________________ 1 57. 2 - 12MM 0. 850. YES YES
2 243. 2 - 12MM 0. 850. YES YES
1 57. 2 - 12MM 0. 1130. YES NO
2 57. 2 - 12MM 1287. 2150. NO YES 1 57. 2 - 12MM 0. 774. YES NO
3 243. 2 - 12MM 0. 2150. YES YES 2 57. 2 - 12MM 930. 2150. NO YES
3 243. 2 - 12MM 0. 2150. YES YES B E A M N O. 63 D E S I G N R E S U L T S - SHEAR
B E A M N O. 59 D E S I G N R E S U L T S - SHEAR AT START SUPPORT - Vu= 2.80 KNS Vc= 66.14 KNS Vs= 0.00 KNS
B E A M N O. 61 D E S I G N R E S U L T S - SHEAR Tu= 0.24 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED.
AT START SUPPORT - Vu= 1.26 KNS Vc= 36.80 KNS Vs= 0.00 KNS AT END SUPPORT - Vu= 0.21 KNS Vc= 66.14 KNS Vs= 0.00 KNS
Tu= 0.11 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 AT START SUPPORT - Vu= 4.58 KNS Vc= 36.80 KNS Vs= 0.00 KNS Tu= 0.24 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED. Tu= 0.12 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 4.58 KNS Vc= 36.80 KNS Vs= 0.00 KNS STIRRUPS ARE NOT REQUIRED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 60
Tu= 0.11 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 AT END SUPPORT - Vu= 1.26 KNS Vc= 36.80 KNS Vs= 0.00 KNS
STIRRUPS ARE NOT REQUIRED. Tu= 0.12 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 56 STIRRUPS ARE NOT REQUIRED. ___ 39J____________________ 850X 200X 300_____________________ 46J____
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 58 | |
||=========================================================================||
___ 36J____________________ 2150X 200X 300_____________________ 35J____ | 2No12 H 243. 0.TO 850 |
| | ___ 31J____________________ 2150X 200X 300_____________________ 39J____ | |
| 2No12 H 57. 0.TO 850 | ||=========================================================================|| | |
||=========================================================================|| | | |___________________________________________________________________________|
| | |___________________________________________________________________________| _________ _________ _________ _________ _________ _________
|___________________________________________________________________________| _________ _________ _________ _________ _________ _________ | | | | | | | | | | | |
_________ _________ _________ _________ _________ _________ | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
|_________| |_________| |_________| |_________| |_________| |_________|
ACI 318-11 BEAM NO. 87 DESIGN RESULTS
ACI 318-11 BEAM NO. 81 DESIGN RESULTS =============================================
ACI 318-11 BEAM NO. 73 DESIGN RESULTS =============================================
============================================= LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEN - 1000. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS LEVEL HEIGHT BAR INFO FROM TO ANCHOR
LEVEL HEIGHT BAR INFO FROM TO ANCHOR (MM) (MM) (MM) STA END
LEVEL HEIGHT BAR INFO FROM TO ANCHOR (MM) (MM) (MM) STA END _____________________________________________________________________
(MM) (MM) (MM) STA END _____________________________________________________________________
_____________________________________________________________________
1 57. 2 - 12MM 0. 800. YES YES
1 57. 2 - 12MM 0. 800. YES YES
1 57. 2 - 12MM 0. 1000. YES YES 2 243. 2 - 12MM 0. 800. YES YES
2 243. 2 - 12MM 0. 394. YES NO
3 243. 2 - 12MM 0. 1000. YES YES B E A M N O. 87 D E S I G N R E S U L T S - SHEAR
B E A M N O. 81 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 0.65 KNS Vc= 34.13 KNS Vs= 0.00 KNS
B E A M N O. 73 D E S I G N R E S U L T S - SHEAR Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
AT START SUPPORT - Vu= 15.30 KNS Vc= 36.46 KNS Vs= 0.00 KNS STIRRUPS ARE NOT REQUIRED.
Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11 AT END SUPPORT - Vu= 1.60 KNS Vc= 34.13 KNS Vs= 0.00 KNS
AT START SUPPORT - Vu= 1.62 KNS Vc= 36.67 KNS Vs= 0.00 KNS NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
Tu= 0.25 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. STIRRUPS ARE NOT REQUIRED.
STIRRUPS ARE NOT REQUIRED. PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 164. MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 65
AT END SUPPORT - Vu= 14.29 KNS Vc= 35.68 KNS Vs= 0.00 KNS
Tu= 0.25 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 11 AT END SUPPORT - Vu= 17.55 KNS Vc= 35.22 KNS Vs= 0.00 KNS
NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11 ___ 68J____________________ 800X 200X 300_____________________
65J____
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. NO STIRRUPS ARE REQUIRED FOR TORSION. | |
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 263. MM REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. | |
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 164. MM | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 61 | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 63 | 2No12 H 57. 0.TO 800 |
||=========================================================================||
___ 55J____________________ 999X 200X 300_____________________ 30J____ | |
| | ___ 62J____________________ 800X 200X 300_____________________ 39J____ |___________________________________________________________________________|
||=========================================================================|| | | _________ _________ _________ _________ _________ _________
| 2No12 H 243. 0.TO 1394 | | | | | ||=========================================================================|| | | | | | | | | | | | |
| | | 4*12c/c122 | | | 2No12 H 243.| 0.TO 800| | | | | | | | | | | | | | | | |
| 2No12 H 57. 0.TO 1000 | | | | | | 3*12c/c122 | | | 3*12c/c122 | | | | | | | | | | | | | |
||=========================================================================|| | 2No12 H 57.| 0.TO 800| | | | | | | | | | | | | | | | |
| | ||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
|___________________________________________________________________________| | | | oo | | oo | | oo | | oo | | oo | | oo |
_________ _________ _________ _________ _________ _________ |___________________________________________________________________________| | | | | | | | | | | | |
| | | | | | | | | | | | _________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
| oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | | ACI 318-11 BEAM NO. 90 DESIGN RESULTS
| oo | | oo | | oo | | oo | | oo | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo |
|_________| |_________| |_________| |_________| |_________| |_________| | | | | | | | | | | | | LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
|_________| |_________| |_________| |_________| |_________| |_________|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
ACI 318-11 BEAM NO. 76 DESIGN RESULTS _____________________________________________________________________
============================================= ACI 318-11 BEAM NO. 84 DESIGN RESULTS
=============================================
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS 1 57. 2 - 12MM 0. 600. YES YES
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END LEVEL HEIGHT BAR INFO FROM TO ANCHOR
_____________________________________________________________________ (MM) (MM) (MM) STA END B E A M N O. 90 D E S I G N R E S U L T S - SHEAR
_____________________________________________________________________
1 57. 2 - 12MM 0. 800. YES YES AT START SUPPORT - Vu= 0.42 KNS Vc= 34.65 KNS Vs= 0.00 KNS
2 243. 2 - 12MM 0. 394. YES NO 1 57. 2 - 12MM 0. 800. YES YES Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
3 243. 2 - 12MM 306. 800. NO YES STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 0.45 KNS Vc= 34.65 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
B E A M N O. 84 D E S I G N R E S U L T S - SHEAR STIRRUPS ARE NOT REQUIRED.
B E A M N O. 76 D E S I G N R E S U L T S - SHEAR DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 66
AT START SUPPORT - Vu= 0.81 KNS Vc= 35.21 KNS Vs= 0.00 KNS
AT START SUPPORT - Vu= 1.48 KNS Vc= 35.20 KNS Vs= 0.00 KNS Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 ___ 71J____________________ 600X 200X 300_____________________ 68J____
Tu= 0.24 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED. | |
STIRRUPS ARE NOT REQUIRED. AT END SUPPORT - Vu= 1.44 KNS Vc= 35.21 KNS Vs= 0.00 KNS | |
AT END SUPPORT - Vu= 0.77 KNS Vc= 35.10 KNS Vs= 0.00 KNS Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 | |
Tu= 0.24 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED. | |
STIRRUPS ARE NOT REQUIRED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 64 | 2No12 H 57. 0.TO 600 |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 62 ||=========================================================================||
| |
___ 65J____________________ 800X 200X 300_____________________ 62J____ |___________________________________________________________________________|
___ 46J____________________ 800X 200X 300_____________________ 55J____ | | _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | | | | |
||=========================================================================|| | | | | | | | | | | | | | |
| 2No12 H 243. 0.TO 394 2No12 H 243. 306.TO 800 | | | | | | | | | | | | | | |
| | | 2No12 H 57. 0.TO 800 | | | | | | | | | | | | |
| 2No12 H 57. 0.TO 800 | ||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| ACI 318-11 BEAM NO. 121 DESIGN RESULTS
=============================================
ACI 318-11 BEAM NO. 141 DESIGN RESULTS
LEN - 780. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS =============================================
ACI 318-11 BEAM NO. 93 DESIGN RESULTS
============================================= LEVEL HEIGHT BAR INFO FROM TO ANCHOR LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
(MM) (MM) (MM) STA END
LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS _____________________________________________________________________ LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
LEVEL HEIGHT BAR INFO FROM TO ANCHOR _____________________________________________________________________
(MM) (MM) (MM) STA END 1 57. 2 - 12MM 0. 780. YES YES
_____________________________________________________________________ 2 243. 2 - 12MM 0. 780. YES YES
1 57. 2 - 12MM 0. 800. YES YES
2 243. 2 - 12MM 0. 394. YES NO
1 57. 2 - 12MM 0. 600. YES YES
2 243. 2 - 12MM 0. 544. YES NO B E A M N O. 121 D E S I G N R E S U L T S - SHEAR
B E A M N O. 141 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 14.50 KNS Vc= 38.18 KNS Vs= 0.00 KNS
B E A M N O. 93 D E S I G N R E S U L T S - SHEAR Tu= 0.23 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11
NO STIRRUPS ARE REQUIRED FOR TORSION. AT START SUPPORT - Vu= 1.33 KNS Vc= 35.14 KNS Vs= 0.00 KNS
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. Tu= 0.26 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
AT START SUPPORT - Vu= 2.17 KNS Vc= 36.48 KNS Vs= 0.00 KNS PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 154. MM STIRRUPS ARE NOT REQUIRED.
Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 AT END SUPPORT - Vu= 0.92 KNS Vc= 35.09 KNS Vs= 0.00 KNS
STIRRUPS ARE NOT REQUIRED. AT END SUPPORT - Vu= 16.61 KNS Vc= 35.96 KNS Vs= 0.00 KNS Tu= 0.26 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
AT END SUPPORT - Vu= 1.30 KNS Vc= 36.48 KNS Vs= 0.00 KNS Tu= 0.23 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11 STIRRUPS ARE NOT REQUIRED.
Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 NO STIRRUPS ARE REQUIRED FOR TORSION. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 71
STIRRUPS ARE NOT REQUIRED. REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 67 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 154. MM
___ 42J____________________ 800X 200X 300_____________________
76J____
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 69 | |
___ 73J____________________ 599X 200X 300_____________________ 71J____ ||==================================== |
| | | 2No12 H 243. 0.TO 394 |
||=================================================================== | ___ 76J____________________ 780X 200X 300_____________________ 28J____ | |
| 2No12 H 243. 0.TO 544 | | | | 2No12 H 57. 0.TO 800 |
| | ||=========================================================================|| ||=========================================================================||
| 2No12 H 57. 0.TO 600 | | 2No12 H 243.| 0.TO 780| | | | | | |
||=========================================================================|| | 3*12c/c122 | | | 3*12c/c122 | | |___________________________________________________________________________|
| | | 2No12 H 57.| 0.TO 780| | | | | _________ _________ _________ _________ _________ _________
|___________________________________________________________________________| ||=========================================================================|| | | | | | | | | | | | |
_________ _________ _________ _________ _________ _________ | | | oo | | oo | | oo | | | | | | |
| | | | | | | | | | | | |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | | | | | |
| oo | | oo | | oo | | oo | | oo | | | _________ _________ _________ _________ _________ _________ | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
|_________| |_________| |_________| |_________| |_________| |_________| | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| ACI 318-11 BEAM NO. 142 DESIGN RESULTS
=============================================
ACI 318-11 BEAM NO. 96 DESIGN RESULTS
============================================= LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
ACI 318-11 BEAM NO. 140 DESIGN RESULTS
LEN - 400. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS ============================================= LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
LEVEL HEIGHT BAR INFO FROM TO ANCHOR LEN - 400. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS _____________________________________________________________________
(MM) (MM) (MM) STA END
_____________________________________________________________________ LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END 1 57. 2 - 12MM 0. 600. YES YES
_____________________________________________________________________ 2 243. 2 - 12MM 0. 544. YES NO
1 57. 2 - 12MM 0. 400. YES YES
2 243. 2 - 12MM 0. 400. YES YES
1 57. 2 - 12MM 0. 400. YES YES
2 243. 2 - 12MM 0. 400. YES YES B E A M N O. 142 D E S I G N R E S U L T S - SHEAR
B E A M N O. 96 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 2.18 KNS Vc= 36.46 KNS Vs= 0.00 KNS
B E A M N O. 140 D E S I G N R E S U L T S - SHEAR Tu= 0.03 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED.
** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 96 IS BEYOND AT END SUPPORT - Vu= 1.31 KNS Vc= 36.46 KNS Vs= 0.00 KNS
THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED. Tu= 0.03 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 140 IS BEYOND STIRRUPS ARE NOT REQUIRED.
THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 72
** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 96 IS BEYOND
THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 140 IS BEYOND ___ 91J____________________ 599X 200X 300_____________________ 79J____
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 68 THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED. | |
||=================================================================== |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 70 | 2No12 H 243. 0.TO 544 |
___ 45J____________________ 400X 200X 300_____________________ 73J____ | |
| | | 2No12 H 57. 0.TO 600 |
||=========================================================================|| ___ 41J____________________ 400X 200X 300_____________________ 91J____ ||=========================================================================||
| 2No12 H 243. 0.TO 400 | | | | |
| | ||=========================================================================|| |___________________________________________________________________________|
| 2No12 H 57. 0.TO 400 | | 2No12 H 243. 0.TO 400 | _________ _________ _________ _________ _________ _________
||=========================================================================|| | | | | | | | | | | | | | |
| | | 2No12 H 57. 0.TO 400 | | oo | | oo | | oo | | oo | | oo | | |
|___________________________________________________________________________| ||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | |
_________ _________ _________ _________ _________ _________ | | | | | | | | | | | | | |
| | | | | | | | | | | | |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | _________ _________ _________ _________ _________ _________ | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | oo | | oo | | oo | | oo | | oo | | oo | |_________| |_________| |_________| |_________| |_________| |_________|
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | |
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
|_________| |_________| |_________| |_________| |_________| |_________| | oo | | oo | | oo | | oo | | oo | | oo | ACI 318-11 BEAM NO. 143 DESIGN RESULTS
| | | | | | | | | | | | =============================================
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
LEVEL HEIGHT BAR INFO FROM TO ANCHOR (MM) (MM) (MM) STA END B E A M N O. 148 D E S I G N R E S U L T S - SHEAR
(MM) (MM) (MM) STA END _____________________________________________________________________
_____________________________________________________________________
AT START SUPPORT - Vu= 0.17 KNS Vc= 32.06 KNS Vs= 0.00 KNS
1 57. 2 - 12MM 0. 800. YES YES Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
1 57. 2 - 12MM 0. 600. YES YES STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 0.08 KNS Vc= 32.06 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
B E A M N O. 145 D E S I G N R E S U L T S - SHEAR STIRRUPS ARE NOT REQUIRED.
B E A M N O. 143 D E S I G N R E S U L T S - SHEAR DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 77
AT START SUPPORT - Vu= 0.81 KNS Vc= 35.16 KNS Vs= 0.00 KNS
AT START SUPPORT - Vu= 0.42 KNS Vc= 34.63 KNS Vs= 0.00 KNS Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 ___ 98J____________________ 600X 200X 300_____________________
99J____
Tu= 0.03 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED. | |
STIRRUPS ARE NOT REQUIRED. AT END SUPPORT - Vu= 1.44 KNS Vc= 35.16 KNS Vs= 0.00 KNS | |
AT END SUPPORT - Vu= 0.45 KNS Vc= 34.63 KNS Vs= 0.00 KNS Tu= 0.02 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 | |
Tu= 0.03 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6 STIRRUPS ARE NOT REQUIRED. | |
STIRRUPS ARE NOT REQUIRED. DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 75 | 2No12 H 57. 0.TO 600 |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 73 ||=========================================================================||
| |
___ 86J____________________ 800X 200X 300_____________________ 80J____ |___________________________________________________________________________|
___ 79J____________________ 600X 200X 300_____________________ 89J____ | | _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | |
| | | 2No12 H 57. 0.TO 800 | | | | | | | | | | | | |
| 2No12 H 57. 0.TO 600 | ||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
||=========================================================================|| | | | oo | | oo | | oo | | oo | | oo | | oo |
| | |___________________________________________________________________________| | | | | | | | | | | | |
|___________________________________________________________________________| _________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
_________ _________ _________ _________ _________ _________ | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | ACI 318-11 BEAM NO. 153 DESIGN RESULTS
| | | | | | | | | | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | oo | | oo | | oo | | oo | | oo | | oo |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | LEN - 350. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
| | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
|_________| |_________| |_________| |_________| |_________| |_________| LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
ACI 318-11 BEAM NO. 146 DESIGN RESULTS
ACI 318-11 BEAM NO. 144 DESIGN RESULTS =============================================
============================================= 1 57. 2 - 12MM 0. 350. YES YES
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
LEVEL HEIGHT BAR INFO FROM TO ANCHOR (MM) (MM) (MM) STA END B E A M N O. 153 D E S I G N R E S U L T S - SHEAR
(MM) (MM) (MM) STA END _____________________________________________________________________
_____________________________________________________________________
1 57. 2 - 12MM 0. 800. YES YES ** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 153 IS BEYOND
1 57. 2 - 12MM 0. 800. YES YES THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
2 243. 2 - 12MM 0. 800. YES YES
B E A M N O. 146 D E S I G N R E S U L T S - SHEAR ** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 153 IS BEYOND
THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
B E A M N O. 144 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 0.65 KNS Vc= 34.10 KNS Vs= 0.00 KNS DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 78
Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
AT START SUPPORT - Vu= 15.22 KNS Vc= 36.43 KNS Vs= 0.00 KNS STIRRUPS ARE NOT REQUIRED.
Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11 AT END SUPPORT - Vu= 1.59 KNS Vc= 34.10 KNS Vs= 0.00 KNS ___ 40J____________________ 350X 200X 300_____________________ 106J____
NO STIRRUPS ARE REQUIRED FOR TORSION. Tu= 0.02 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6 | |
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. STIRRUPS ARE NOT REQUIRED. | |
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 164. MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 76 | |
| |
AT END SUPPORT - Vu= 17.47 KNS Vc= 35.21 KNS Vs= 0.00 KNS | 2No12 H 57. 0.TO 350 |
Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 11 ___ 89J____________________ 800X 200X 300_____________________ 86J____ ||=========================================================================||
NO STIRRUPS ARE REQUIRED FOR TORSION. | | | |
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. | | |___________________________________________________________________________|
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 164. MM | | _________ _________ _________ _________ _________ _________
| | | | | | | | | | | | | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 74 | 2No12 H 57. 0.TO 800 | | | | | | | | | | | | |
||=========================================================================|| | | | | | | | | | | | |
| | | | | | | | | | | | | |
___ 80J____________________ 800X 200X 300_____________________ 36J____ |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | _________ _________ _________ _________ _________ _________ | oo | | oo | | oo | | oo | | oo | | oo |
||=========================================================================|| | | | | | | | | | | | | | | | | | | | | | | | |
| 2No12 H 243.| 0.TO 800| | | | | | | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
| 3*12c/c122 | | | 3*12c/c122 | | | | | | | | | | | | | |
| 2No12 H 57.| 0.TO 800| | | | | | | | | | | | | | | | |
||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | oo | | oo | | oo | | oo | | oo | | oo | ACI 318-11 BEAM NO. 154 DESIGN RESULTS
|___________________________________________________________________________| | | | | | | | | | | | | =============================================
_________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | LEVEL HEIGHT BAR INFO FROM TO ANCHOR
| | | | | | | | | | | | ACI 318-11 BEAM NO. 148 DESIGN RESULTS (MM) (MM) (MM) STA END
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | ============================================= _____________________________________________________________________
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
|_________| |_________| |_________| |_________| |_________| |_________| 1 57. 2 - 12MM 0. 800. YES YES
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
ACI 318-11 BEAM NO. 145 DESIGN RESULTS B E A M N O. 154 D E S I G N R E S U L T S - SHEAR
=============================================
1 57. 2 - 12MM 0. 600. YES YES
AT START SUPPORT - Vu= 0.52 KNS Vc= 36.37 KNS Vs= 0.00 KNS | |
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 ___ 112J____________________ 800X 200X 300_____________________ 109J____ |___________________________________________________________________________|
STIRRUPS ARE NOT REQUIRED. | | _________ _________ _________ _________ _________ _________
AT END SUPPORT - Vu= 0.13 KNS Vc= 36.37 KNS Vs= 0.00 KNS | | | | | | | | | | | | | |
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 | | | | | | | | | | | | | |
STIRRUPS ARE NOT REQUIRED. | | | | | | | | | | | | | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 79 | 2No12 H 57. 0.TO 800 | | | | | | | | | | | | |
||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | oo | | oo | | oo | | oo | | oo | | oo |
___ 101J____________________ 800X 200X 300_____________________ 104J____ |___________________________________________________________________________| | | | | | | | | | | | |
| | _________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| 2No12 H 57. 0.TO 800 | | | | | | | | | | | | | ACI 318-11 BEAM NO. 179 DESIGN RESULTS
||=========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| | | oo | | oo | | oo | | oo | | oo | | oo |
|___________________________________________________________________________| | | | | | | | | | | | | LEN - 400. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
_________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | LEVEL HEIGHT BAR INFO FROM TO ANCHOR
| | | | | | | | | | | | (MM) (MM) (MM) STA END
| | | | | | | | | | | | _____________________________________________________________________
| | | | | | | | | | | | ACI 318-11 BEAM NO. 172 DESIGN RESULTS
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | =============================================
| oo | | oo | | oo | | oo | | oo | | oo | 1 57. 2 - 12MM 0. 400. YES YES
| | | | | | | | | | | | LEN - 890. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
|_________| |_________| |_________| |_________| |_________| |_________|
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END B E A M N O. 179 D E S I G N R E S U L T S - SHEAR
_____________________________________________________________________
ACI 318-11 BEAM NO. 160 DESIGN RESULTS
=============================================
1 57. 2 - 12MM 0. 836. YES NO ** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 179 IS BEYOND
LEN - 850. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END B E A M N O. 172 D E S I G N R E S U L T S - SHEAR ** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 179 IS BEYOND
_____________________________________________________________________ THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
AT START SUPPORT - Vu= 0.33 KNS Vc= 35.92 KNS Vs= 0.00 KNS DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 84
1 57. 2 - 12MM 16. 850. NO YES Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 1.15 KNS Vc= 35.92 KNS Vs= 0.00 KNS ___ 106J____________________ 400X 200X 300_____________________ 122J____
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 | |
B E A M N O. 160 D E S I G N R E S U L T S - SHEAR STIRRUPS ARE NOT REQUIRED. | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 82 | |
| |
AT START SUPPORT - Vu= 1.13 KNS Vc= 65.88 KNS Vs= 0.00 KNS | 2No12 H 57. 0.TO 400 |
Tu= 0.00 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 ___ 104J____________________ 890X 200X 300_____________________ 43J____ ||=========================================================================||
STIRRUPS ARE NOT REQUIRED. | | | |
AT END SUPPORT - Vu= 0.38 KNS Vc= 65.88 KNS Vs= 0.00 KNS | | |___________________________________________________________________________|
Tu= 0.00 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 | | _________ _________ _________ _________ _________ _________
STIRRUPS ARE NOT REQUIRED. | | | | | | | | | | | | | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 80 | 2No12 H 57. 0.TO 836 | | | | | | | | | | | | |
||====================================================================== | | | | | | | | | | | | |
| | | | | | | | | | | | | |
___ 44J____________________ 850X 200X 300_____________________ 101J____ |___________________________________________________________________________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | _________ _________ _________ _________ _________ _________ | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | | |
| 2No12 H 57. 16.TO 850 | | | | | | | | | | | | |
|==========================================================================|| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | |
| | | oo | | oo | | oo | | oo | | oo | | | ACI 318-11 BEAM NO. 186 DESIGN RESULTS
|___________________________________________________________________________| | | | | | | | | | | | | =============================================
_________ _________ _________ _________ _________ _________ |_________| |_________| |_________| |_________| |_________| |_________|
| | | | | | | | | | | | LEN - 600. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
| | | | | | | | | | | |
| | | | | | | | | | | | LEVEL HEIGHT BAR INFO FROM TO ANCHOR
| | | | | | | | | | | | ACI 318-11 BEAM NO. 173 DESIGN RESULTS (MM) (MM) (MM) STA END
| | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | ============================================= _____________________________________________________________________
| | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
|_________| |_________| |_________| |_________| |_________| |_________| 1 57. 2 - 12MM 0. 600. YES YES
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
ACI 318-11 BEAM NO. 163 DESIGN RESULTS B E A M N O. 186 D E S I G N R E S U L T S - SHEAR
=============================================
1 57. 2 - 12MM 0. 800. YES YES
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS AT START SUPPORT - Vu= 1.65 KNS Vc= 34.04 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
LEVEL HEIGHT BAR INFO FROM TO ANCHOR STIRRUPS ARE NOT REQUIRED.
(MM) (MM) (MM) STA END B E A M N O. 173 D E S I G N R E S U L T S - SHEAR AT END SUPPORT - Vu= 1.39 KNS Vc= 34.04 KNS Vs= 0.00 KNS
_____________________________________________________________________ Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED.
AT START SUPPORT - Vu= 0.10 KNS Vc= 31.49 KNS Vs= 0.00 KNS DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 85
1 57. 2 - 12MM 0. 800. YES YES Tu= 0.00 KN-MET Tc= 0.8 KN-MET Ts= 0.0 KN-MET LOAD 6
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 0.74 KNS Vc= 31.49 KNS Vs= 0.00 KNS ___ 122J____________________ 599X 200X 300_____________________ 98J____
Tu= 0.00 KN-MET Tc= 0.8 KN-MET Ts= 0.0 KN-MET LOAD 6 | |
B E A M N O. 163 D E S I G N R E S U L T S - SHEAR STIRRUPS ARE NOT REQUIRED. | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 83 | |
| |
AT START SUPPORT - Vu= 0.44 KNS Vc= 32.61 KNS Vs= 0.00 KNS | 2No12 H 57. 0.TO 600 |
Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6 ___ 99J____________________ 800X 200X 300_____________________ 112J____ ||=========================================================================||
STIRRUPS ARE NOT REQUIRED. | | | |
AT END SUPPORT - Vu= 1.08 KNS Vc= 32.61 KNS Vs= 0.00 KNS | | |___________________________________________________________________________|
Tu= 0.00 KN-MET Tc= 0.9 KN-MET Ts= 0.0 KN-MET LOAD 6 | | _________ _________ _________ _________ _________ _________
STIRRUPS ARE NOT REQUIRED. | | | | | | | | | | | | | |
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 81 | 2No12 H 57. 0.TO 800 | | | | | | | | | | | | |
||=========================================================================|| | | | | | | | | | | | |
| | | | | | | | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | | | | | | | ooo | | ooo | | ooo | | ooo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | ooo | | ooo | | ooo | | ooo | | | | | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | |_________| |_________| |_________| |_________| |_________| |_________| | 3#12 | | 3#12 | | 3#12 | | 3#12 | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| | ooo | | ooo | | ooo | | ooo | | | | |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|
ACI 318-11 BEAM NO. 194 DESIGN RESULTS
ACI 318-11 BEAM NO. 190 DESIGN RESULTS =============================================
============================================= ********************END OF BEAM DESIGN**************************
LEN - 2051. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEN - 800. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR 220. DESIGN COLUMN 1 TO 8 10 TO 12 35 TO 46
LEVEL HEIGHT BAR INFO FROM TO ANCHOR (MM) (MM) (MM) STA END DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 90
(MM) (MM) (MM) STA END _____________________________________________________________________
_____________________________________________________________________
1 57. 2 - 12MM 0. 1565. YES NO
1 57. 2 - 12MM 0. 759. YES NO 2 243. 3 - 12MM 717. 2051. NO YES ACI 318-11 COLUMN NO. 1 DESIGN RESULTS
===============================================
B E A M N O. 190 D E S I G N R E S U L T S - SHEAR B E A M N O. 194 D E S I G N R E S U L T S - SHEAR FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 900.0 SQ. MM
AT START SUPPORT - Vu= 0.71 KNS Vc= 35.13 KNS Vs= 0.00 KNS AT START SUPPORT - Vu= 10.55 KNS Vc= 35.68 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 Tu= 0.04 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
STIRRUPS ARE NOT REQUIRED. STIRRUPS ARE NOT REQUIRED. ----------------------------------------------------------
AT END SUPPORT - Vu= 1.36 KNS Vc= 35.13 KNS Vs= 0.00 KNS AT END SUPPORT - Vu= 29.13 KNS Vc= 36.77 KNS Vs= 2.08 KNS
Tu= 0.00 KN-MET Tc= 1.0 KN-MET Ts= 0.0 KN-MET LOAD 6 Tu= 0.04 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 8 - 12 MM 1.005 6 END 0.650
STIRRUPS ARE NOT REQUIRED. NO STIRRUPS ARE REQUIRED FOR TORSION. (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 86 REINFORCEMENT IS REQUIRED FOR SHEAR. TIE BAR NUMBER 12 SPACING 192.00 MM
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 789. MM
___ 109J____________________ 800X 200X 300_____________________ 44J____ DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 88
| | ACI 318-11 COLUMN NO. 2 DESIGN RESULTS
| | ===============================================
| | ___ 43J____________________ 2050X 200X 300_____________________ 29J____
| | | |
| 2No12 H 57. 0.TO 759 | | =================================================|| FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
||======================================================================= | | 3No12 H 243. 717.TO 2051 | | | ONLY MINIMUM STEEL IS REQUIRED.
| | | | | | | 8*12c/c122 | AREA OF STEEL REQUIRED = 900.0 SQ. MM
|___________________________________________________________________________| | 2No12 H 57. 0.TO 1565 | | | | |
_________ _________ _________ _________ _________ _________ ||========================================================= | BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
| | | | | | | | | | | | | | ----------------------------------------------------------
| | | | | | | | | | | | |___________________________________________________________________________|
| | | | | | | | | | | | _________ _________ _________ _________ _________ _________ 8 - 12 MM 1.005 6 END 0.650
| | | | | | | | | | | | | | | | | | | | | | | | (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | | | | | ooo | | ooo | | ooo | | ooo | TIE BAR NUMBER 12 SPACING 192.00 MM
| oo | | oo | | oo | | oo | | oo | | | | | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| | | | | | | | | | | | | | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________| | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | |
| oo | | oo | | oo | | oo | | | | | ACI 318-11 COLUMN NO. 3 DESIGN RESULTS
| | | | | | | | | | | | ===============================================
|_________| |_________| |_________| |_________| |_________| |_________|
ACI 318-11 BEAM NO. 193 DESIGN RESULTS
============================================= FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS ACI 318-11 BEAM NO. 195 DESIGN RESULTS AREA OF STEEL REQUIRED = 900.0 SQ. MM
============================================= DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 91
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END LEN - 2050. MM FY - 414. FC - 21. MPA, SIZE - 200. X 300. MMS
_____________________________________________________________________ BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
LEVEL HEIGHT BAR INFO FROM TO ANCHOR ----------------------------------------------------------
(MM) (MM) (MM) STA END
1 57. 3 - 12MM 0. 1492. YES NO _____________________________________________________________________ 8 - 12 MM 1.005 6 END 0.650
2 243. 3 - 12MM 545. 2050. NO YES (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
1 57. 3 - 12MM 0. 1514. YES NO
2 243. 3 - 12MM 545. 2050. NO YES
B E A M N O. 193 D E S I G N R E S U L T S - SHEAR
ACI 318-11 COLUMN NO. 4 DESIGN RESULTS
===============================================
AT START SUPPORT - Vu= 16.53 KNS Vc= 36.27 KNS Vs= 0.00 KNS B E A M N O. 195 D E S I G N R E S U L T S - SHEAR
Tu= 0.20 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6
NO STIRRUPS ARE REQUIRED FOR TORSION. FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. AT START SUPPORT - Vu= 19.00 KNS Vc= 36.37 KNS Vs= 0.00 KNS ONLY MINIMUM STEEL IS REQUIRED.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 788. MM Tu= 0.06 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 AREA OF STEEL REQUIRED = 900.0 SQ. MM
NO STIRRUPS ARE REQUIRED FOR TORSION.
AT END SUPPORT - Vu= 19.65 KNS Vc= 36.73 KNS Vs= 0.00 KNS REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
Tu= 0.20 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 788. MM ----------------------------------------------------------
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1. AT END SUPPORT - Vu= 22.13 KNS Vc= 36.83 KNS Vs= 0.00 KNS 8 - 12 MM 1.005 6 END 0.650
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 788. MM Tu= 0.06 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 6 (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
NO STIRRUPS ARE REQUIRED FOR TORSION. TIE BAR NUMBER 12 SPACING 192.00 MM
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 87 REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 122. MM C/C FOR 788. MM
___ 40J____________________ 2049X 200X 300_____________________ 33J____ DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 89 ACI 318-11 COLUMN NO. 5 DESIGN RESULTS
| | ===============================================
| =======================================================||
| 3No12 H 243. 545.TO 2050 | | | ___ 44J____________________ 2049X 200X 300_____________________ 31J____
| 8*12c/c122 | | | | | | | 8*12c/c122 | | | FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
| 3No12 H 57. 0.TO 1492 | | | | | | | | =======================================================|| ONLY MINIMUM STEEL IS REQUIRED.
||====================================================== | | 3No12 H 243. 545.TO 2050 | | | AREA OF STEEL REQUIRED = 900.0 SQ. MM
| | | 8*12c/c122 | | | | | | | 8*12c/c122 |
|___________________________________________________________________________| | 3No12 H 57. 0.TO 1514 | | | | | | | BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
_________ _________ _________ _________ _________ _________ ||======================================================= | ----------------------------------------------------------
| | | | | | | | | | | | | |
| | | | | ooo | | ooo | | ooo | | ooo | |___________________________________________________________________________| 8 - 12 MM 1.005 6 END 0.650
| | | | | 3#12 | | 3#12 | | 3#12 | | 3#12 | _________ _________ _________ _________ _________ _________ (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
| | | | | | | | | | | | | | | | | | | | | | | | TIE BAR NUMBER 12 SPACING 192.00 MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI ONLY MINIMUM STEEL IS REQUIRED.
---------------------------------------------------------- AREA OF STEEL REQUIRED = 900.0 SQ. MM
ACI 318-11 COLUMN NO. 6 DESIGN RESULTS 8 - 12 MM 1.005 6 END 0.650 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
=============================================== (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) ----------------------------------------------------------
TIE BAR NUMBER 12 SPACING 192.00 MM
8 - 12 MM 1.005 6 END 0.650
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 92 (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ACI 318-11 COLUMN NO. 35 DESIGN RESULTS
ONLY MINIMUM STEEL IS REQUIRED. ===============================================
AREA OF STEEL REQUIRED = 900.0 SQ. MM
ACI 318-11 COLUMN NO. 41 DESIGN RESULTS
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ===============================================
---------------------------------------------------------- ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 900.0 SQ. MM
8 - 12 MM 1.005 6 END 0.650 FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI ONLY MINIMUM STEEL IS REQUIRED.
TIE BAR NUMBER 12 SPACING 192.00 MM ---------------------------------------------------------- AREA OF STEEL REQUIRED = 900.0 SQ. MM
8 - 12 MM 1.005 6 END 0.650 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) ----------------------------------------------------------
ACI 318-11 COLUMN NO. 7 DESIGN RESULTS TIE BAR NUMBER 12 SPACING 192.00 MM
=============================================== 8 - 12 MM 1.005 6 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ACI 318-11 COLUMN NO. 36 DESIGN RESULTS
ONLY MINIMUM STEEL IS REQUIRED. ===============================================
AREA OF STEEL REQUIRED = 900.0 SQ. MM
ACI 318-11 COLUMN NO. 42 DESIGN RESULTS
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ===============================================
---------------------------------------------------------- ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 900.0 SQ. MM
8 - 12 MM 1.005 6 END 0.650 FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI AREA OF STEEL REQUIRED = 952.2 SQ. MM
TIE BAR NUMBER 12 SPACING 192.00 MM ----------------------------------------------------------
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
8 - 12 MM 1.005 6 END 0.650 ----------------------------------------------------------
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
ACI 318-11 COLUMN NO. 8 DESIGN RESULTS TIE BAR NUMBER 12 SPACING 192.00 MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 97
===============================================
12 - 12 MM 1.508 11 STA 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ACI 318-11 COLUMN NO. 37 DESIGN RESULTS TIE BAR NUMBER 12 SPACING 192.00 MM
ONLY MINIMUM STEEL IS REQUIRED. ===============================================
AREA OF STEEL REQUIRED = 900.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 95 ACI 318-11 COLUMN NO. 43 DESIGN RESULTS
---------------------------------------------------------- ===============================================
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
8 - 12 MM 1.005 6 END 0.650 ONLY MINIMUM STEEL IS REQUIRED.
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) AREA OF STEEL REQUIRED = 900.0 SQ. MM FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
TIE BAR NUMBER 12 SPACING 192.00 MM ONLY MINIMUM STEEL IS REQUIRED.
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 93 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI AREA OF STEEL REQUIRED = 900.0 SQ. MM
----------------------------------------------------------
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
8 - 12 MM 1.005 6 END 0.650 ----------------------------------------------------------
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
ACI 318-11 COLUMN NO. 10 DESIGN RESULTS TIE BAR NUMBER 12 SPACING 192.00 MM 8 - 12 MM 1.005 6 END 0.650
=============================================== (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ACI 318-11 COLUMN NO. 38 DESIGN RESULTS
ONLY MINIMUM STEEL IS REQUIRED. ===============================================
AREA OF STEEL REQUIRED = 900.0 SQ. MM ACI 318-11 COLUMN NO. 44 DESIGN RESULTS
===============================================
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
---------------------------------------------------------- AREA OF STEEL REQUIRED = 952.2 SQ. MM
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
8 - 12 MM 1.005 6 END 0.650 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI ONLY MINIMUM STEEL IS REQUIRED.
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) ---------------------------------------------------------- AREA OF STEEL REQUIRED = 900.0 SQ. MM
TIE BAR NUMBER 12 SPACING 192.00 MM
12 - 12 MM 1.508 11 STA 0.650 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) ----------------------------------------------------------
TIE BAR NUMBER 12 SPACING 192.00 MM
ACI 318-11 COLUMN NO. 11 DESIGN RESULTS 8 - 12 MM 1.005 6 END 0.650
=============================================== (PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
ACI 318-11 COLUMN NO. 39 DESIGN RESULTS
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ===============================================
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 900.0 SQ. MM ACI 318-11 COLUMN NO. 45 DESIGN RESULTS
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ===============================================
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI ONLY MINIMUM STEEL IS REQUIRED.
---------------------------------------------------------- AREA OF STEEL REQUIRED = 900.0 SQ. MM
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
8 - 12 MM 1.005 6 END 0.650 BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI ONLY MINIMUM STEEL IS REQUIRED.
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE) ---------------------------------------------------------- AREA OF STEEL REQUIRED = 900.0 SQ. MM
TIE BAR NUMBER 12 SPACING 192.00 MM DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 98
8 - 12 MM 1.005 6 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
ACI 318-11 COLUMN NO. 12 DESIGN RESULTS DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 96 ----------------------------------------------------------
===============================================
8 - 12 MM 1.005 6 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED TIE BAR NUMBER 12 SPACING 192.00 MM
ONLY MINIMUM STEEL IS REQUIRED. ACI 318-11 COLUMN NO. 40 DESIGN RESULTS
AREA OF STEEL REQUIRED = 900.0 SQ. MM ===============================================
DXF IMPORT OF 2-STOREY MINGLANILLA STRUCTURAL.DXF -- PAGE NO. 94
ACI 318-11 COLUMN NO. 46 DESIGN RESULTS
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED ===============================================
FY - 413.7 FC - 20.7 MPA, SQRE SIZE - 300.0 X 300.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 900.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
8 - 12 MM 1.005 6 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM
********************END OF COLUMN DESIGN RESULTS********************
221. END CONCRETE DESIGN
222. FINISH
You might also like
- Structural Analysis: Proposed Three (3) Storeys Residential100% (1)Structural Analysis: Proposed Three (3) Storeys Residential4 pages
- Structural Design Criteria: Figure 1. Perspective of The Residential BuildingNo ratings yetStructural Design Criteria: Figure 1. Perspective of The Residential Building7 pages
- Structural Analysis and Design Report: 3-Bedroom Bungalow Residence Lot 19, BLK 9 Gleenrose Subd. Valenzuela CityNo ratings yetStructural Analysis and Design Report: 3-Bedroom Bungalow Residence Lot 19, BLK 9 Gleenrose Subd. Valenzuela City85 pages
- Sample Structural Analysis and Design Criteria79% (39)Sample Structural Analysis and Design Criteria5 pages
- Complete Structural Analysis 2 Storey Commercial at SuquiNo ratings yetComplete Structural Analysis 2 Storey Commercial at Suqui93 pages
- Design Criteria Proposed Two Storey Residential 1No ratings yetDesign Criteria Proposed Two Storey Residential 115 pages
- Proposed-5-Storey-Building-Sta Mesa MlaNo ratings yetProposed-5-Storey-Building-Sta Mesa Mla87 pages
- Design Criteria Proposed Two Storey Residential 188% (8)Design Criteria Proposed Two Storey Residential 149 pages
- Detailed Structural Analysis and Design: NSEC SS Outdoor Lighting Post100% (1)Detailed Structural Analysis and Design: NSEC SS Outdoor Lighting Post19 pages
- Structural Analysis and Calculations: Two-Storey Residential Building100% (1)Structural Analysis and Calculations: Two-Storey Residential Building19 pages
- Preparation of Statement of Basis of DesignNo ratings yetPreparation of Statement of Basis of Design3 pages
- Detailed Structural Analysis and Design: MAEC SS Outdoor Lighting PostNo ratings yetDetailed Structural Analysis and Design: MAEC SS Outdoor Lighting Post19 pages
- Structural Design and Analysis Report - 090407100% (1)Structural Design and Analysis Report - 090407144 pages
- Industrial Waste Heat Recovery: Alfred PiggottNo ratings yetIndustrial Waste Heat Recovery: Alfred Piggott9 pages
- Paper - Interpretation and Misinterpretation of Sonic Logging Test Results100% (1)Paper - Interpretation and Misinterpretation of Sonic Logging Test Results6 pages
- 12 - Elasticity and Fluid Machanics-01 TheoryNo ratings yet12 - Elasticity and Fluid Machanics-01 Theory32 pages
- Technical Notes: Short Tendon ElongationsNo ratings yetTechnical Notes: Short Tendon Elongations4 pages
- An Introduction To Statistical Mechanics and Thermodynamics 2nd Edition Robert H. Swendsen DownloadNo ratings yetAn Introduction To Statistical Mechanics and Thermodynamics 2nd Edition Robert H. Swendsen Download131 pages
- Physics Cluster Test 02 (Solution) - 30.12.2024No ratings yetPhysics Cluster Test 02 (Solution) - 30.12.20243 pages
- Donald R. Askeland, Pradeep P. Fulay, Wendelin J. Wright - The Science and Engineering of Materials, Sixth Edition - CL-Engineering (2010)No ratings yetDonald R. Askeland, Pradeep P. Fulay, Wendelin J. Wright - The Science and Engineering of Materials, Sixth Edition - CL-Engineering (2010)2 pages
- D 6473 - 15 Standard Test Method For Specific Gravity and Absorption of Rock..No ratings yetD 6473 - 15 Standard Test Method For Specific Gravity and Absorption of Rock..4 pages
- Chemistry Investigatory Project - KaranNo ratings yetChemistry Investigatory Project - Karan10 pages
- A Review On Vampire Electricity: Abstract - This Paper Portrays The Different Procedures Used ToNo ratings yetA Review On Vampire Electricity: Abstract - This Paper Portrays The Different Procedures Used To3 pages
- Eastern Cape Trial Analytical Geometry Marking Guidelines100% (1)Eastern Cape Trial Analytical Geometry Marking Guidelines40 pages
- Mechanical Properties of Solids: ElasticityNo ratings yetMechanical Properties of Solids: Elasticity12 pages
