SIREMOBIL Iso-C 3D

SP

System

Software Description
3D Reconstruction and 3D Navigation

© Siemens AG 2001
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_ design,_are_ reserved.

English
Print No.: SPR2-230.815.01.05.02 Doc. Gen. Date: 10.04
Replaces: SPR2-230.815.01.04.02
0-2 Revision

Chapter Page Revision

all all 05

Document revision level

The document corresponds to the version/revision level effective at the time of system delivery. Revi-
sions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.

Disclaimer
The installation and service of equipment described herein is to be performed by qualified personnel
who are employed by Siemens or one of its affiliates or who are otherwise authorized by Siemens or
one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated with or autho-
rized by Siemens or one of its affiliates are directed to contact one of the local offices of Siemens or
one of its affiliates before attempting installation or service procedures.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Contents 0-3

Page
1 _______Requirements / Remarks / Introduction ____________________________ 1 - 1

Note regarding the windows shown . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Note regarding software versions . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Test equipment, tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Required documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Important remarks regarding start-up . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
General remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Text emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Abbreviations used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

2 _______Preparations___________________________________________________ 2 - 1

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
General requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

3 _______Settings / Programming _________________________________________ 3 - 1

Prerequisites for Host and Memoskop SW Update . . . . . . . . . . . . . . . . . . .3-1

Installation of the system service software at the service PC . . . . . . . . . . . . . .3-2
Preliminary work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Saving the system parameters to a disk. . . . . . . . . . . . . . . . . . . . . . . . .3-2
Installing the Iso-C software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Saving the MEMOSKOP parameters to a disk . . . . . . . . . . . . . . . . . . .3-4
Downloading the MEMOSKOP software . . . . . . . . . . . . . . . . . . . . . .3-6
Downloading the MEMOSKOP with empty Flash Proms . . . . . . . . . . . . . .3-8
Checking the MEMOSKOP software . . . . . . . . . . . . . . . . . . . . . . . 3 - 10
Storage configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 10

4 _______3D Software ___________________________________________________ 4 - 1

Installing the SIREMOBIL Iso-C 3D software for

3D reconstruction and 3D navigation . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Change of Directory permissions . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Starting the Syngo service software . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Installation of available SW patches. . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13

5 _______Downloading the Control Software ________________________________ 5 - 1

Control software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

6 _______Mechanical Settings ____________________________________________ 6 - 1

Orbital potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Possible errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

Siemens AG SPR2-230.815.01 Page 3 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
0-4 Contents

Page
Orbital angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Possible errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Angulation angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Possible errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Setting the reconstruction region . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Possible errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

7 ______ Monitor / Display Settings________________________________________7 - 1

Monitor SIMOMED N 100/120Hz, part number 11 02 628 . . . . . . . . . . . . . . . 7-1

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Call up the MEMOSCOPE SMPTE test image . . . . . . . . . . . . . . . . . . . 7-1
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Monitor Standard 100/120Hz, part number 30 64 581 . . . . . . . . . . . . . . . . . 7-2
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Call up the MEMOSCOPE SMPTE test image . . . . . . . . . . . . . . . . . . . 7-2
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Monitor SIMOMED HM, part number 37 92 079 . . . . . . . . . . . . . . . . . . . . 7-3
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Switch-over to 2D Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Installing and starting the SIMOMED HM service software. . . . . . . . . . . . . 7-3
Brightness and contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Monitor geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Pre-settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Optimum setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
TFT display BARCO MVG 1318, part number 80 79 530 . . . . . . . . . . . . . . . 7-9
Operation OSD menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Note on the checks of the automatic videotiming recognition . . . . . . . . . . .7 - 11
Videotiming check for standard timing: . . . . . . . . . . . . . . . . . . . . . . .7 - 12
Manual setting of brightness and contrast . . . . . . . . . . . . . . . . . . . . .7 - 13
Checks during timing in ”Stand-Alone” mode: . . . . . . . . . . . . . . . . . . .7 - 14
Check of the timing 3D reconstruction . . . . . . . . . . . . . . . . . . . . . . .7 - 15

8 ______ Syngo Configuration ____________________________________________8 - 1

Customer and site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Local host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Site info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
TCP/IP LAN settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
User settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Monitor type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 10
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 10
Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 10
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 12
Autotransfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 13
Eventlog settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 14

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Contents 0-5

Page
Backup & Restore settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 15
Licensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 16
DICOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 17
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 17
Character settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 18
Offline device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 19
Network node settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 21
Print device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 24
Hardcopy overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 28
Modification and test capability of the previously entered data . . . . . . . . . . 8 - 28
LUT file settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 29
HIS/RIS nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 32
Patient registration settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 35
Viewer settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 35
CorRea settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 36
MPPS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 36
Worklist result settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 37

9 _______3D Limiting Resolution and Calibration ____________________________ 9 - 1

Without 3D Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1

With 3D Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
3D Navigation option is enabled . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
3D Navigation option is not enabled . . . . . . . . . . . . . . . . . . . . . . . . .9-1

10 ______Customer Settings_____________________________________________ 10 - 1

General remarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
Setting the desired user interface language (normally done during installation) . . . 10 - 1
Setting the country-specific keyboard layout (normally done during installation) . . . 10 - 2
Printing on a video printer with Syngo. . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Other customer-specific settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 6

11 ______Function Test in the Network ____________________________________ 11 - 1

12 ______Backup / Restore ______________________________________________ 12 - 1

Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
General remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 4
Restore SW settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 6
Restore user settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 7
Manual SW settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 8

13 ______Notes on Backup and Restore ___________________________________ 13 - 1

14 ______Data table for connected Stations ________________________________ 14 - 1

Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1

Siemens AG SPR2-230.815.01 Page 5 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
0-6 Contents

Page
15 _____ Final Work Steps ______________________________________________15 - 1

Final work steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 - 1

16 _____ Changes to previous version ____________________________________16 - 1

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Requirements / Remarks / Introduction 1 1-1

Note regarding the windows shown 1

The windows shown in this document are for illustration and orientation purposes.
They may differ from the actual layout of the windows under MS WINDOWS.

Note regarding software versions 1

This document was revised on release of software version VB00B. Any software versions
stated here therefore serve as examples only and must be replaced by the current soft-
ware version.
The software versions may differ slightly in the installation routine. Therefore please
observe the relevant menus shown.

Safety information 1

CAUTION When performing the work steps and tests, the product-specific
safety information contained in the documents as well as the gen-
eral safety information TD00-000.860.01.01 must be observed.

Test equipment, tools and aids 1

NOTICE All tools, test equipment and aids, with the exception of the
"standard installation tool kit", are listed and specified in the
Service Tool Catalog.

• SPOTMETER for SMfit ACT (replaces MAVO Monitor) 077 52 848

• Service PC (only for SIMOMED monitor)
• Blank CDs, alternatively several floppy disks
• HTML test images (floppy disk) 075 58 567

NOTE Use only CD-Rs, since CD-RWs may be incompatible with Syngo.

Required documents 1

• Operating instructions of the monitors / TFT displays to be installed

• If BARCO monitors MVG 1318, part number 80 79 530, are present:
Replacement instructions TD00-000.841.17...

Siemens AG SPR2-230.815.01 Page 1 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
1-2 Requirements / Remarks / Introduction

Important remarks regarding start-up 1

General remarks 1

• The system must be completely cabled but not connected to the network.

Text emphasis 1

Emphasized texts in technical documentation have the following meaning:

DANGER DANGER indicates when there is an immediate danger that leads

to death or serious physical injury.

WARNING WARNING indicates a risk of danger that may lead to death or

serious physical injury.

CAUTION CAUTION used with the safety alert symbol indicates a risk of
danger that leads to slight or moderate physical injury and/ or
damage to property.

NOTICE NOTICE used without the safety alert symbol indicates a risk of
danger that if disregarded leads or may lead to a potential situa-
tion which may result in an undesirable result or state other than
death, physical injury or property damage.

All texts labeled with the ” p ” symbol must be transcribed into the Test Certificate
included in the shipment.
These measurement values can then be used for the Acceptance Test required in Ger-
many according to §16 of the Röntgenverordnung or for other national requirements.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Requirements / Remarks / Introduction 1-3
Abbreviations used 1

AE Title Application Entity Title

DHCP Dynamic host configurations protocol
DNS Domain Name System
HCC Hard Copy Camera
HIS/RIS Hospital/Radiology Information System
Hub Center point
ID Identification
IEC International Electrotechnical Commission
ISK Allen screws
MM Multimeter
PG Planning Guide
RADIS Radiological Image Station (designation for image station)
SSW Service Software
SPDI Siemens Parallel Digital Interface
TCP/IP Transmission Control Protocol/Internet Protocol
TB Collimator
VDE Verband Deutscher Elektrotechniker
WINS Windows Internet Name Service
DICOM Digital Imaging and Communication in Medicine
IP Internet Protocol
Q/R Query / Retrieve
SCP Service Class Provider
SCU Service Class User
TCP Transfer Control Protocol
JPEG Joint Photographic Experts Group
RAS Remote Access Service
PPP Point to Point Protocol
USC Uptime Service Center
HSC Headquarter Support Center
TFT Thin Film Transistor

Siemens AG SPR2-230.815.01 Page 3 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
1-4 Requirements / Remarks / Introduction
Definitions 1

AE Title (AET) DICOM Application Entity Title. Must be unique in a DICOM network.

Conformance Each manufacturer of a DICOM device has to provide this type of state-
Statement ment, since it provides an overview of the product’s DICOM capability.

DHCP Dynamic Host Configuration Protocol. Reduces the complexity of con-

figuring computers for TCP/IP networks. The following TCP/IP configu-
ration can be dynamically assigned by a DHCP server: IP Address,
Subnet masks, gateway and additional parameters, such as domain
name.

DNS The Domain Name Service is used to resolve the TCP/IP address from
a user-friendly host name.

Dongle Device plugged into the parallel port of the computer that provides a
unique ID for license handling.
A security or copy protection device for commercial microcomputer pro-
grams consisting of a serialized EPROM and several drivers in a D-25
connector shell, which must be connected to an I/O port of the com-
puter while the program is running. Programs that use a dongle query
the port at start-up and at subsequent programmed intervals. The pro-
grams terminate if the port (dongle)does not respond with the dongle's
programmed validation code.

Hub Distributor in a network using the star topology. A hub allows data
transfer between computers.

IP Address 32-bit address assigned to hosts using TCP/IP. An IP address belongs

to one of four classes (A, B, C, D) and is written as 4 octets separated
by periods (dotted decimal format). Each address consists of a network
number, an optional sub-network number and a host number. The net-
work and the subnet numbers are used for routing, while the host num-
ber is used to address an individual host within the network or the sub-
network. A subnet mask is used to extract network and sub-network
information from the IP address.
The IP is part of the socket address.

Port Part of the socket address. Different DICOM services on the same host
PC may use different port numbers.

Subnet mask The subnet mask is used to extract network and sub network informa-
tion from the IP address.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Requirements / Remarks / Introduction 1-5

Router A device that connects different networks. Different means either a dif-
ferent architecture or a different type of protocol. In a TCP/IP environ-
ment, a router is used to connect computers that are located in different
IP address ranges.

Service Key Required to enter the service UI. The key has to be generated prior to
the first software installation.

Socket The socket address consists of the IP and the port number.
Address
WINS provides a distributed database for registration and querying
WINS dynamic Net-BIOS names to IP addresses.

Vendor ID Unique identification number provided by a dongle.

Compression Running a data set through an alogrithm which reduces the space
required
Remote A service that allows remote clients running Microsoft Windows or Win-
Access dows NT to dial into a network.
Service

Siemens AG SPR2-230.815.01 Page 5 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
1-6 Requirements / Remarks / Introduction
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Preparations 2 2-1

Requirements 2

System requirements 2

The system requirements are described in the document “Planning Guide: Pub. No.
SPR2-230.021. .....".

General requirements 2

NOTICE A service key is required to configure the station. If the 3D option

was installed in the factory, the service key can be found in the
system logbook. Otherwise it must be created in the intranet
before starting work. URL: http://www-td.med.siemens.de
A key for Service Level 7 is required.
Please have the Dongle ID ready, which is needed to create a ser-
vice key. Please contact the appropriate personnel in the
Regional Unit.
The generation process is described in ARTD-001.719.12.01.
“Service/ Application Licensing Process”.

• The SIREMOBIL Iso-C 3D must be connected and operational.

• The cables for the network are available but not yet connected.
• All the required configuration data must be available, i.e. the configuration table in the
PG or in the Software Description must be completed accordingly.
• The SIREMOBILl Iso-C 3D software package must be available.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
2-2 Preparations
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3 3-1

Prerequisites for Host and Memoskop SW Update 3

NOTICE Please note the service PC settings.

Prior to starting the software updates, please observe the following:

- The serial interface cable used has to be fully wired and be OK.
- Switch off the screen saver and end the programs running in background.
- Check the jumpers D1.X95 / D1.D96 / D1.X 99. They should be set to position 2-3.
- Check the serial port FIFO settings of your service PC. The FIFO of the serial port must
be enabled (default settings).
- In case of correct host but incorrect MEMOSKOP communication, temporarily switch
D1.S3.2 to position ON. Ignore the error messages displayed at the SIREMOBIL user
console. Ignore the MEMOSKOP service software error message "No communication
with the X-ray system" and close it by clicking the "Ignore" button. Select the correct
type of MEMOSKOP and begin the necessary service work. After completion of the
MEMOSKOP service steps, switch D1.S3.2 back to the OFF position.
- Do not use the "SCENIC MOBILE 350" service PC. It is not compatible.

*
FIFO settings
Steps for Windows in English
• Select the Windows footer
• Select "Start"
• Select "Settings"
• Select "Control Panel"
• Select "System"
• Select "Device Manager"
• Select "Ports"
• Select "COM Port"
• Select "Port Settings"
• Select "Advanced.."
• "Use FIFO buffers" must be marked with "V"

Siemens AG SPR2-230.815.01 Page 1 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3-2 Settings / Programming

Installation of the system service software at the service PC 3

• Delete any existing MEMOSKOP service software from the hard drive of the Service PC .
• Install the MEMOSKOP service software (3 disks, material no. 30 99 715 G5437) on the
Service PC.
• For SIREMOBIL ISO-C systems, install the system software supplied (Material no.
56 46 653 G5464 system disk 2) on the Service PC.

Preliminary work 3

• Remove the back cover of the monitor trolley (important for installing the MEMOSKOP
software).

Saving the system parameters to a disk 3

• Connect the Service PC to the serial port of the SIREMOBIL.

• Insert the parameter disk 2 of the SIREMOBIL system software from the update kit into
drive A of the Service PC.
• Start the system service program and log on to the system ("System" menu - "Connect",
"Logon" button).
• Confirm the question "Password has been changed. Put new Password to Unit?" by
clicking the "Yes" button.
• Close the "Password expires on 00:00:00" info by clicking the "OK" button.
• The " Service PC- SIREMOBIL .... " program window is displayed.
• Select the "Data" - "Backup" menu.
• Select the "Parameters" line and start the backup. The remark line may be empty.
• Go back to the main menu of the service program.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3-3

Installing the Iso-C software 3

• Select the "Data" menu in the menu bar of the " Service PC- SIREMOBIL ... " program
window. .

NOTE Fig. shows the "Data: Download" window as an example.

In the "File version" column, the actual version of the system
software will be displayed.

• Select the "Download" menu.

• The "Data: Download Select Component" program window is displayed.
• Select the "SMC PLUS" component and start downloading by clicking "OK".
• Confirm the "Flash-EPROMs of the selected component will be erased. This process
may take some time. Confirm the "Do you want to continue?" question by clicking "Yes".
• Start downloading by clicking "Start".

NOTICE Only the host (SMC PLUS) has to be downloaded. The download
procedure is the same for all SIREMOBIL systems. The only dif-
ference are the software versions.

• After the download, wait approx. 1 minute while the system reboots.
• Close the download window by clicking "Cancel".
• Log out from the service program ("System" menu - "Logoff").
• Enter "Field Test SW downloaded" under service entry.

Siemens AG SPR2-230.815.01 Page 3 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3-4 Settings / Programming
• Exit the service program ("System" menu - "Quit").
• Switch the system off and then back on again.
• The SIREMOBIL is once again ready for operation.
• Replace the existing system software with the new software and file this info in the
system manual.
• If the parameters are changed after the installation, the item "Saving the system
parameters to a disk " must be performed again.

Saving the MEMOSKOP parameters to a disk 3

NOTICE Please note the prerequisites.

NOTICE Save the parameters to a disk before starting the MEMOSKOP

download.
If the parameter set cannot be saved to disk, read out the
MEMOSKOP parameters (User setup and Technical setup) and
record them.

NOTICE If a transfer error or "ComPort", "Download", "Get from

Memoskop", "Put to Memoskop" error messages or errors recur
when the loading the language file, repeat this function several
times. If the problem persists, exit the service software.
Switch the SIREMOBIL off and then back on, wait for power-up
and start the service software again. Perform the last work step
again.

• Insert the Memoskop "User Programs" disk into drive A of the service PC.
• Start the MEMOSKOP service software.
• Enter the password and press the Return key on the PC.
• Select the required serial interface on the service PC.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3-5
The "Memoskop Service Program" program window is displayed.

• After the main menu appears, click the button "Get from Memoskop" and wait for the
transfer of the parameters from the MEMOSKOP to the PC. After the transfer, the status
line shows "....Receiving configuration done".
• Then save the parameters to the diskette (menu "File", submenu "Save").
• Enter the current date as the file name. Use the file extension "mem".
Example:
The current date is: (DD_MM_YY) 28_07_03
Enter the file name + file extension: 28_07_03.mem
• Wait for the parameters to be saved to disk.

NOTE Please read the prerequisites in case of errors while transferring

the MEMOSKOP parameters to the service PC (e.g. communica-
tion errors).

NOTICE If the MEMOSKOP service program needs to be restarted, switch

the unit off and then back on again.

Siemens AG SPR2-230.815.01 Page 5 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3-6 Settings / Programming
• If it is not possible to save the MEMOSKOP parameter set to the disk, all parameters
(User setup and Technical setup) must be read out and recorded.

Downloading the MEMOSKOP software 3

NOTICE Please read the prerequisites on page 7 in case of errors during

the downloading of the MEMOSKOP software (e.g. communica-
tion errors).
If this is the case, stop the download procedure and attempt to
download the software as described in the section "Downloading
the MEMOSKOP with empty Flash Proms."

• For the MEMOSKOP displayed, insert the corresponding diskette supplied in drive A of
the Service PC (MEMOSKOP software).
• Select the "Download" menu.
• Select "Select file for Download:" .
• The "Open File" program window opens.
• Select drive A.
• Select the file xVxxxxx.mot) and confirm selection with "OK".
(first x = 3 or 4, depending on existing MEMOSKOP.
subsequent x = place holder for the actual SW Version code. See below).
3 MEMOSKOP C-E 100/ C/ C-MOD Select 3Vxxxxx.mot
4 MEMOSKOP CSub/ CSub-MOD Select 4Vxxxxx.mot

NOTICE If the service program is not able to automatically recognize the

MEMOSKOP installed, select the MEMOSKOP type manually.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3-7
• Select "Erase FLASHes".
• Press the reset button for 4 seconds on the back of the MEMOSKOP, as soon as
possible.
ê While the Flash Proms are being erased, dots will be displayed in the status line.
ê After erasing, the "...Ready" message will be displayed in the status line.
ê The DOWNLOAD button is now selectable.

NOTE The "Download File" button must be pressed (clicked) within

1.5 minutes maximum!

• After a successful download, the "Download complete" message will be displayed in the
status line.

NOTICE If the download is not performed in full (communication errors or

undefined symbols in the status line), stop the download proce-
dure and follow the description under "Downloading the
MEMOSKOP with empty Flash Proms".

• Exit the Service program.

• Switch the unit off and then back on again (wait for entire power-up sequence).
• Restart the Service program.

Siemens AG SPR2-230.815.01 Page 7 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3-8 Settings / Programming
Downloading the MEMOSKOP with empty Flash Proms 3

NOTE This section describes the downloading procedure for the MEMOSKOP
with empty Flash Proms. Skip this section if dowloading was suc-
cessfully completed as described.

• Switch the unit off and exit the Memoskop service program.
• Remove the cover of the basic unit and the rear cover of the monitor trolley.
• Set the service switch D1.S3.2 to the ON position.
• Switch on the unit. Ignore the error messages displayed on the user console.
• Insert the corresponding diskette supplied in drive A of the Service PC (MEMOSKOP
software ).
• Start the MEMOSKOP service program and enter the password.
• Select the serial interface of the service PC.
• Ignore the message "No communication with the X-Ray system. Therefore click the
button "Ignore".
• In response to the error message "The Program didn’t receive the version message from
the Memoskop", manually select the MEMOSKOP model.

3 MEMOSKOP C-E 100/ C/ C-MOD

4 MEMOSKOP CSub/ CSub-MOD

• Select the "Download" menu.

• Select "Select file for Download:".
• The program window "Open File" opens.
• Select drive A.
Select the file xVxxxxx.mot) and confirm selection with "OK".
(first x = 3 or 4, depending on existing MEMOSKOP.
subsequent x = place holder for the actual SW Version code. See below).
3 MEMOSKOP C-E 100/ C/ C-MOD Select 3Vxxxxx.mot
4 MEMOSKOP CSub/ CSub-MOD Select 4Vxxxxx.mot

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 8 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3-9

• Select "Erase FLASHes" .

• Press the reset button on the back of the MEMOSKOP for 4 seconds as soon as
possible.
ê While the Flash Proms are being erased, dots are displayed in the status line.
ê After erasing, the "...Ready" message is displayed in the status line.
ê The DOWNLOAD button is now selectable.

NOTICE The "Download File" button must be pressed (clicked) within

1.5 minutes maximum!

• Select "Download File" .

NOTE It will take approximately 20 minutes to load the new

MEMOSKOP software.

• After successful completion of the Download, the "Download complete" message will be
displayed in the status line.
• Wait until the MEMOSKOP is rebooted.
• Exit the Service program.
• Switch off the unit.
• Set the service switch D1.S3.2 back to the OFF position.
• Switch the unit on (wait for entire power-up sequence).

NOTE If the download is not performed completely (communication

errors or undefined symbols in the status line), read the prere-
quisites.
Stop the download procedure, end the MEMOSKOP service pro-
gram, switch off the unit and repeat the download procedure as
described in section "Download with empty Flash Proms".

Siemens AG SPR2-230.815.01 Page 9 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3 - 10 Settings / Programming
The MEMOSKOP parameters are stored to a disk
• Switch on the unit.
• Start the MEMOSKOP service program.
• Select the menu "File" - "Open".
• Select the previously stored MEMOSKOP parameter file (example name was
28_07_01.mem) and click the "OK" button. The stored parameters will be transferred to
the service software.
• Select the "Mode" menu as well as the sub-menus for the operating modes and user
programs. Read the stored parameters and manually reprogram the parameters at the
MEMOSKOP keyboard (User setup / Technical setup).
• Select the "Hardcopy" menu. Read the stored parameters and manually reprogram the
parameters at the MEMOSKOP keyboard (User setup / Technical setup).
• Select the "Monitor" menu. Read the stored parameters and manually reprogram the
parameters at the MEMOSKOP keyboard (User setup / Technical setup).
• Select the "Other" menu. Read the stored parameters and manually reprogram the
parameters at the MEMOSKOP keyboard(User setup / Technical setup).
MEMOSKOP Parameters are recorded manually
• The MEMOSKOP parameters were recorded previously. Reprogram all parameters at
the MEMOSKOP keyboard.

Checking the MEMOSKOP software 3

• Call "User Setup".

• The text displayed must correspond to the language file loaded.
• The software version of the MEMOSKOPS must be displayed in the first line.
• Exit "User Setup" with the "Home" button.

Storage configuration 3

• Start the SIREMOBIL Iso-C again. It will take approx. 2 minutes.

• To get the largest possible reconstructed volume, select the largest possible blanking
circle.
• Move the C-arm into the basic position.
• Select the technical SET UP: use "CTRL-T" password‚..............'
• Select the parameter: "Circle Maske setup".
• Select the parameter: "change circle mask radius". The monitor displays a cross and an
arrow.
• Use the arrow key to enlarge the radius up to the image margin. Please note that you
have to be able to see the entire arrow.
• Wait until the arrow disappears.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 10 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Settings / Programming 3 - 11
• Press the "Home" key until the "Technical Set Up Menu" display appears.
• Select "More Selections".
• Select "Interface to 3D-PC" .
• Click "Yes".
• Press "enter" .
• Press the "Home" key until the "Technical Set Up Menu" display appears.
• Select "Diagnostics".
• Select "Enable Bridge"
• Select "Yes" and store it by pressing the "Enter" key.
• Select "Bridge delay".
• Enter the numerical value "120".
• Press "enter".
• Press the "Home" key.

Perform the activities listed below in accordance with the Service Instructions
SPR2-230.061.01.xx Version 08 or higher.
Set the following:
Collimator, X-Iris
Collimator, Slot diaphragm
Collimator display on the monitor
Correction of the 0° position of the slot diaphragm display

Siemens AG SPR2-230.815.01 Page 11 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
3 - 12 Settings / Programming
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 12 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4 4-1

Installing the SIREMOBIL Iso-C 3D software for

3D reconstruction and 3D navigation 4

NOTE The 3D Navigation option is either already part of the 3D software

on the system or is supplied on the 3D software CD in the
"Iso-C 3D Navigation Kit".

• The SIREMOBIL Iso-C must be switched off.

Video switch 1 button

"Memoskop SCSI Adapter"

"power plug"

• The rear panels of the monitor trolley and the 3D-PC must be removed.
• Disconnect the "Memoskop SCSI Adapter" plug from the PC.
• Disconnect the "power plug" from the MEMOSKOP.
• Disconnect the "DICOM power plug" from the 3D PC
• Connect the Dongle, if not already connected.
• Release the video switch-over switch 1 (to the left as viewed from the back of the
monitor), i.e., the switch should not be pressed.
• Restart the SIREMOBIL Iso-C.
• Insert the CD with the Iso-C 3D software.

Siemens AG SPR2-230.815.01 Page 1 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4-2 3D Software
• Switch off the SIREMOBIL Iso-C and wait until the system has shut down completely.
• Restart the Siremobil Iso-C.
ê The PC will start automatically. The start-up can be viewed on the right monitor.
ê After approx. 5 to 15 minutes the following message appears on the screen:

= Installation complete …===========================

|| System and image partition were set up. ||
|| Please make sure there is no disk in the floppy drive ||
|| (Press any key to reboot the system now) ||
|| IMPORTANT : While the system is rebooting, eject ||
|| the CD-ROM and remove it from the drive ! ||
===============================================

• Press the space bar and remove the CD.

• Switch on and off at the monitor trolley.
ê The 3D PC will reboot.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4-3
ê Wait until the following screen appears.
Ignore the message concerning monitor settings.

• Enter the 3D PC name (ID no. of the computer; this is located on the PC label).
• Press the "Enter" key 2x.
ê The computer will shut down and restart automatically.
ê Internet Explorer will start; the following screen will appear.

Siemens AG SPR2-230.815.01 Page 3 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4-4 3D Software
Change of Directory permissions 4

NOTE Before entering the license key, the access rights for the
Med_Pixel drive must be changed as described below.

Click the Start button and select the "Logoff Meduser" menu.
Press and hold down the Shift key and then click the Yes button.
The "Logon Information" window is displayed.
You can now release the Shift key.
In the "Logon Information" window, enter "administrator" as user name.
In the "Logon Information" window, enter "adm$pwd$4$med" as password.
Click the OK button to close the window.

Open the Windows NT Explorer (Menu "Start - Programs - Windows NT Explorer").

Select the "Med_Pixel (E:)" drive and press the right mouse button.
Click "Properties" in the popup menu. The "Med_Pixel (E:) Properties" window is dis-
played.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4-5
Select the "Security" tab.
In the "Security" window, select the "Permissions" button. The "Directory Permissions"
window is displayed.
In the "Directory Permissions" window, select the checkbox marked "Replace Permissions
on Subdirectories".
In the "Directory Permissions" window, click the "Add" button. The "Add Users and
Groups" window is displayed.
In the "Add Users and Groups" window, under "Names:", click "Everyone" and accept the
selection by clicking the "Add" button.
In the "Add Users and Groups" window, in the "Type of Access:" selection window, select
"Full control" and confirm by clicking the OK button.
Close all windows by clicking the OK button.
Restart the PC by clicking "Start"- Shutdown - Restart - OK.
Wait until the system has booted.
The "Logon Message" window is displayed. Close this window by clicking the OK button.
The "Logon Information" window appears.
Enter "meduser" as user name.
Enter "@medUser000" as password. (For the @ symbol, press Shift + 2).
Close the window by clicking OK.
The Internet Explorer will start; the following screen will appear:

Starting the Syngo service software 4

• Select "Click here to start the Local Service Configuration".

Siemens AG SPR2-230.815.01 Page 5 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4-6 3D Software
ê The "Service Software" mask appears.

• Enter the service key under "Please enter password," 14 digits in the first field and
6 digits in the second field. This service key is supplied on paper.
• Select "Set as Default".
• Press the "OK" button.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4-7

• Select "Configuration".

• Select "Next".

Siemens AG SPR2-230.815.01 Page 7 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4-8 3D Software
• Select "Licensing" in the list under Service.

• Insert the disk with the license file.

• Click "Browse".
• Select drive "a".
• Select the file with the extension ".dat".
• Select "Import license file".
• When prompted to overwrite the existing license file, confirm by clicking "OK".
ê The following message will appear "License data successfully saved"
• Select "OK".
• Press the "Home" button.

• Select "Cancel" in the pop-up message. Do not restart the PC!

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 8 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4-9
ê The Syngo interface will appear.

• Select "Utilities".

• Under "Source," select the item "Unlock system key".

• Select "OK".

Siemens AG SPR2-230.815.01 Page 9 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4 - 10 3D Software

Note After exiting the program, the Windows task bar is closed auto-
matically. To display the task bar again, press the key combina-
tion "CTRL" + "ESC".
The "Matrox Display Properties" program is closed automatically
after each setting and selection of the OK button. The program
must be restarted for the next settings (Start - Programs - Matrox
Power desk NT - Matrox Display Properties).

• Press the "CTRL" + "ESC" keys.

• Click "Enter".
ê The windows "Start" button will appear.
• Select "Start".
• Select "Programs".
• Select "Matrox Power Desk NT".
• Select "Matrox Display Properties".

• Select the "Monitor" button.

• Select "Matrox Monitor".
• In the selection window, select "Siemens" by double-clicking.
• Select the "Medical Simomed H @ 72 Hz" monitor.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 10 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4 - 11
• Select "Apply".

• Confirm by clicking "OK".

• Confirm the message by selecting "YES".

ê The monitor resolution has been changed over.

• Under "Current display" select 2.

• Select "Output to TV (PAL)".

Siemens AG SPR2-230.815.01 Page 11 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4 - 12 3D Software
• Confirm by clicking "Apply".

• Confirm by clicking "OK".

• Confirm by clicking "Yes".

• Select "Settings".

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 12 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Software 4 - 13
• Select "True Color (32-bit)".
• Select "72 Hz" refresh frequency.
• Confirm by clicking "OK", even if the other settings are correct.
• Select "Start".
• Select "Shutdown".
• Select "OK" for shutdown.
• Wait until the "restart" prompt appears.
• Shut down the SIREMOBIL Iso C 3D.
• Wait until the SIREMOBIL Iso C 3D has shut down completely.
• Connect the Memoskop power plug.
• Connect the SCSI plug to the Memoskop.
• Remove the diskette.
• Switch on the SIREMOBIL Iso-C 3D.
ê The system will start. Syngo will start on the right monitor.
• Wait until the Syngo task card is displayed.
• Switch off the SIREMOBIL Iso-C 3D.
• Press the video switch-over switch 1(the button is now depressed).
• Switch on the SIREMOBIL Iso-C 3D.
ê The Memoskop image will appear on the right monitor.

Installation of available SW patches 4

• All available patches (i.e. hotfixes) must be installed again, after the installation of the 3D
software. Use the published documents for the installation (SI’s, UI’s...)

Siemens AG SPR2-230.815.01 Page 13 of 14 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
4 - 14 3D Software
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 14 of 14 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Downloading the Control Software 5 5-1

Control software 5

• Switch on the SIREMOBIL Iso-C.

• Select "Option".
• Select "Local Service".
• Enter password.
• Select the "Upgrade Ctr.SW" button.
• Load the CD Upgrade CTR.SW.
• Select "CD:".
• Click the "Go" button.

After the message "download successful" appears:

• Remove the CD.
• Click the "OK" button.

The Reconstruction PC will shut down automatically.

• Switch off the SIREMOBIL Iso-C 3D.
• Restart the SIREMOBIL Iso-C 3D.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
5-2 Downloading the Control Software
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Mechanical Settings 6 6-1

Orbital potentiometer 6

• Restart the system.

• Simultaneously press "Ctrl + D".
• Select "options".
• Select "Local Service", the Service Software window will appear.
• Enter the password when prompted "please enter the 20-digit password." Do not select
"set as default."
• Select "Adjustment Iso-C 3D".
• Move the C-arm to the final position.
• Remove the cover for the drive unit.
• Loosen the Allen screws on the potentiometer.
• Rotate the potentiometer counterclockwise to the end stop.
• Rotate the potentiometer two turns clockwise.
• Retighten the Allen screws on the potentiometer.
• Press "Go." The potentiometer value is displayed.
The new value must be between the X value and the Y value
• If the value is between the X and Y values, press "Save." The message "New Value Data
is saved" will appear.

Possible errors 6

Error Possible cause Corrective measure

Value is not within toler- Potentiometer not prop- Repeat setting.
ance. erly set.
Potentiometer defective, Replace coupling unit.
value must be 200 ohms.

The same value is always Break in line. Check line connections.

displayed.
Emergency shutdown but- Pull out emergency shutdown
ton depressed. button.
No value is displayed. Software error. Restart system.
Other Read out error messages in
Eventlog Reader.
Analyze and treat error mes-
sages according to trouble-
shooting instructions.
Tab. 1 Adjustment of the orbital potentiometer

Siemens AG SPR2-230.815.01 Page 1 of 4 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
6-2 Mechanical Settings

Orbital angle 6

• Move C-arm to the end position = -90°.

• Ensure that the area is free of obstacles.
• Press "Go." C-arm movement will start.
• The message " Start angle is fixed" will appear.

Possible errors 6

Error Possible cause Corrective measure

C-arm travels to the end stop. Improper end switch Repeat setting.
setting.
The message "Start angle is Other Read out error messages in
fixed" does not appear. Eventlog Reader.
Analyze and treat error mes-
sages according to trouble-
shooting instructions.
Tab. 2 Start angle of the orbital angle

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 4 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Mechanical Settings 6-3

Angulation angle 6

• Move the C-arm to 0 degrees angulation.

• Press "Go." The potentiometer value will be displayed. The new value must be between
the X value and the Y value.
• Press "Save".

Possible errors 6

Error Possible cause Corrective measure

Value is outside toler- Improper potentiome- Rotate the installed potentiometer
ance. ter setting. 1x counterclockwise.
Press "Go".
Rotate the installed potentiometer
2x to the left.
Press "Go".
Remove the potentiometer incl.
holder. Rotate the gear wheel until
the markers match exactly.
Reinstall the potentiometer.
Press "Go".
Ohmwert vom Schleifer aus in
beide Richtungen gleichwertig ein-
stellen.
The same value is always Line break. Check connection lines.
displayed.
Emergency shutdown Pull out emergency shutdown but-
button is depressed. ton.
No value is displayed. Other Read out error messages in Event-
log Reader.
Analyze and treat error messages
according to trouble-shooting
instructions.

Tab. 3 Startvalue Potentiometer Angulationsangle

Siemens AG SPR2-230.815.01 Page 3 of 4 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
6-4 Mechanical Settings

Setting the reconstruction region 6

• Make sure no objects are in the beam path.

• Make sure the C-arm path is clear of obstacles.
• "Caution radiation".
• Press "Go".
• After the message " Determination of the Reconstruction Part 1" appears, press "o.k.".
• Press the left footswitch until the message "Move C-Arm in Position Angulation 180°
Orbital -95°" appears.
• Press "o.k.".
• Press "Go".
• After the message "Determination of the Reconstruction Part 2" appears, press "o.k.".
• Press the left footswitch until a value appears on the monitor for Reconstruction Part 2.
• Press "Next." This automatically brings you back to the Home Menu.

Possible errors 6

Error Possible cause Corrective measure

Error is displayed. Object in the beam path. Remove object.
Defective potentiometer. Replace coupling unit.
The value must read
200 ohms.
Other Other Read out error messages in
Eventlog Reader.
Analyze and treat error mes-
sages according to trouble-
shooting instructions.
Tab. 4 Adjustment of the reconstruction region

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 4 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7 7-1

Monitor SIMOMED N 100/120Hz, part number 11 02 628 7

NOTE Always perform the settings for the left monitor first (live image)!

NOTE The part number 11 02 628 is indicated on the type plate of the
monitor.

Prerequisites 7

The ambient light sensor is to be dimmed.

Call up the MEMOSCOPE SMPTE test image 7

• Press "Ctrl” + ”U” followed by ”L” on the Memoscope keyboard.

The SMPTE test image will appear on both monitors.

Brightness 7

• Set the brightness controller so that the 5% patches are distinguishable (visible) in the
test image. Ideally, 1.5 to 2.5 Candela/m² should be set in field 0%.

Contrast 7

• Set the contrast of the left monitor so that the edges of the 100% field are sharp, i.e. there
should be no blooming (overlapping into the brightest image areas).
The target value is approx. 550 Cd/m² in the 100% field.

NOTE If the contrast cannot be set on the left monitor, check whether
the contrast can be set on the monitor that is removed.
If the contrast setting cannot be performed for either monitor, a
new monitor should be ordered after consulting with the
customer.

Siemens AG SPR2-230.815.01 Page 1 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7-2 Monitor / Display Settings

Monitor Standard 100/120Hz, part number 30 64 581 7

NOTE Always perform the settings for the left monitor first (live image)!

NOTE The part number 30 64 581 is indicated on the type plate of the
monitor.

Prerequisites 7

The ambient light sensor is to be dimmed.

Call up the MEMOSCOPE SMPTE test image 7

• Press "Ctrl” + ”U” followed by ”L” on the Memoscope keyboard.

The SMPTE test image will appear on both monitors.

Brightness 7

• Set the brightness controller so that the 5% patches are distinguishable (visible) in the
test image. Ideally, 1.5 to 2.5 Candela/m² should be set in field 0%.

Contrast 7

• Set the contrast of the left monitor so that the edges of the 100% field are sharp, i.e. there
should be no blooming (overlapping into the brightest image areas).
The target value is approx. 350 Cd/m² in the 100% field.

NOTE If the contrast cannot be set on the left monitor, check whether
the contrast can be set on the monitor that is removed.
If the contrast setting cannot be performed for either monitor, a
new monitor should be ordered after consulting with the
customer.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7-3

Monitor SIMOMED HM, part number 37 92 079 7

Prerequisites 7

The left monitor (live image) is already set!

The ambient light sensor is to be dimmed.
Call up the MEMOSCOPE SMPTE test image

• Press "Ctrl” + ”U” simultaneously on the Memoscope keyboard. Then press the "L" key.
The SMPTE test image will appear on both monitors.

Switch-over to 2D Mode 7

• Press "Ctrl-D" on the Memoscope keyboard; this switches over to 2D operation (if not
already on).

Installing and starting the SIMOMED HM service software 7

• Install the "SIMOMED HM - Service Software" included in the delivery volume of the HM
monitor (right monitor) on the service PC (if it is not already installed on the service PC).
• Using the serial cable (99 00 440 RE999), connect the service PC to the HM Simomed
monitor (right monitor) (the interface for the HM monitor is located on the lower left,
behind the cover).
• Start the SIMOMED HM service software on the service PC.
• Log into the monitor using the password ".........."; the menu bar is displayed.
• In the menu, select "Configuration".
• Select "Block sensor-touch keyboard".

Siemens AG SPR2-230.815.01 Page 3 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7-4 Monitor / Display Settings

• Check "Off" for all of the possible settings.

• Select "OK".

Brightness and contrast 7

• The part number 37 92 079 is indicated on the type plate of the monitor.

• In the menu, select "Configuration".

• Select "Brightness and Contrast".
• Set the contrast minimum to "0".

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7-5

• In the 0% field, set the brightness to 2-3 candela/m².

• Set the contrast of the HM monitor so that the brightness of the displayed image appears
subjectively identical to the left monitor (live image).
• If required, repeat the setting.
• The 5% and 95% fields must remain visually distinguishable.

NOTE You need not pay attention to the geometry when setting
brightness and contrast.

• Select "OK".

Siemens AG SPR2-230.815.01 Page 5 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7-6 Monitor / Display Settings
Monitor geometry 7

• In the menu, select "Balance".

• Select "Geometry".

Pre-settings 7

As a first step, the following pre-settings must be made:

• H-S Correction --> 20
• H-Linearity --> 46
• OW-Amplitude --> 23
• OW-Trapezoid --> 27
• OW-Angles --> 29
• Image width coarse --> if present, this should be set to 1
• V-Linearity --> 10
• NS-Amplitude --> 9
• NS-Trapezoid --> 41
• NS-Angle right --> 24
• NS-Angle left --> 12
• NS-Symmetry --> 19

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7-7
Optimum setting 7

23.7cm
23.7cm

• Set the monitor according to the image displayed above. Pay special attention to the
square patches in the test image.
The horizontal length of all 8 test patches should be the same as the vertical ones. (The
reference value is 23.7 cm or 9.3’’ measured on the monitor).
• Center the image horizontally and vertically with the following controllers:
- H-Amplitude
- H-Position
- V-Position
- V-Amplitude

If present, linearity errors (individual boxes are not square) or other deviations should be
corrected using the appropriate controllers.
• H-S Correction
• H-Linearity
• OW-Amplitude
• OW-Trapezoid
• OW-Angles
• V-Linearity
• NS-Amplitude

Siemens AG SPR2-230.815.01 Page 7 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7-8 Monitor / Display Settings
• NS-Trapezoid
• NS-Angle right
• NS-Angle left
• NS-Symmetry
Once the picture is set according to the displayed image:
• Select "OK".
• Press "Ctrl-D" on the Memoscope keyboard to switch to 3D mode.
• Using Syngo, select "Service Patient".

• Select the "1K SMPTE test image". There should be no distortion or non-linearity
present.

NOTE If distortion or non-linearity is present, repeat the section on ”HM

monitor geometry”.

• Shut down the service software.

• Click "Yes" in the dialog box.
• Save the settings on the Simomed HM diskette under the file name "HM.dat".

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 8 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7-9

TFT display BARCO MVG 1318, part number 80 79 530 7

Operation OSD menu 7

NOTE All required adjustments are performed via the OSD menus.

Position Control Wheel

• The control wheel is located at the rear of the TFT display. See above figure /1.
Call up the OSD main menu:
• Turn the control wheel (do not press the wheel).
The OSD main menu is indicated on the top left.
In the ”Scroll” menu:
• Turn the control wheel to change between menus.
The currently selected menu is indicated visually highlighted.
Selection of a menu:
• Select a menu by pressing the control wheel. The relevant submenu will then be
indicated.
Quitting the OSD menu or a submenu
• Select ”Exit” to exit the current screen or the OSD menu.
Saving the settings
• If any settings were modified in the OSD menu, select Exit => Exit ... to change to the
”Save Changes” window.
• Select ”Yes” and press the control wheel to accept the modifications.
Switching off / on:
• Call up OSD (i.e. press the control wheel)
• Select the menu as follows:

Siemens AG SPR2-230.815.01 Page 9 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7 - 10 Monitor / Display Settings
• Switch off (Standby mode) by selecting the ”Stand by” menu (i.e. by pressing the control
wheel).

OSD menu structure

Full Autoset see section ”Setting”

Automatic Geometry n.a.
Autoset Automatic Phase n.a.
Automatic Gain n.a.
EXIT quitting the menu
Video Contrast Adjustment of contrast see section ”Setting”
(signal limitation)
Video Brightness Adjustment of brightness see section ”Setting”
Luminance Adjustment of max. contrast see section ”Setting”
(backlight).
Geometry adjustment of geometry,
only required if height /
OSD menu position are incorrectly
Adjustments set.
Phase => Frequency see section ”Setting”
Man Phase adj see section ”Setting”
Input Selection Selection : Auto standard
Power LED / DPMS standard
Settings Ambient Light OFF
Compensation see section ”Setting”
Preset Gamma with respect to standard
input signal
Information TFT monitor data SW / operating hours ..
EXIT Quitting the OSD menu

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 10 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7 - 11
Note on the checks of the automatic videotiming recognition 7

NOTE Two different videotimings are present on the left TFT display
(live image).
Three different videotimings are present on the right TFT display:
1. Standard Timing (left and right display):
Monitor cart and basic unit are connected to each other;
the synchronization is realized by the video camera.
2. Timing stand-alone operation, monitor cart
(left and right display):
Monitor cart and basic unit are not connected to each other;
the Memoscope is synchronized internally.
3. Timing 3D reconstruction (only right display):
3D reconstruction PC supplies the video signal.
The automatic videotiming recognition of the TFT display needs
to be checked with all present videotimings.

The videotiming is automatically recognized by the TFT display. The following checks
need to be performed with different videotimings.

NOTE If the automatic recognition of one or several videotimings does

not lead to the expected results, you need to adjust the TFT
display manually. Use the replacement instructions of the TFT
display TD00-000.841.17... for this.
(CS-Intranet path: For Service - SP - Surgery - SIREMOBIL Iso-C -
CB-DOC - Service - Monochrome Display).

Siemens AG SPR2-230.815.01 Page 11 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7 - 12 Monitor / Display Settings
Videotiming check for standard timing: 7

The monitor cart and the basic unit are connected to each other.
The plug connection X10 is plugged.
The system is ready for operating.
Both TFT displays need to be checked.
• Call up the ”Memoscope User Setup”. Press simultaneously the keys "CTRL" + "U" on
the Memoscope keyboard.
Select the ”L” menu. The Memoscope SMPTE test image is indicated on both TFT
displays.

NOTE If the 3D PC image is indicated on the right monitor , press

simultaneously the keys "CTRL" + "D" on the Memoscope
keyboard to switch over to the Memoscope video signal.

Visual check of the geometry

- The image position and the aspect ration need to be represented correctly.
The Memoscope SMPTE test image is neither cut nor represented too small.
Visual check of resolution
- In the Memoscope SMPTE test image in the center of the image shows clearly the fine
vertical and horizontal lines.
Visual check of shadings, artifacts and moiré patterns
- The gray-scale values are indicated without shadings.
- Neither artifacts nor moiré patterns are recognizable.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 12 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7 - 13
Manual setting of brightness and contrast 7

On the Memoscope, select LUT 1 for both video outputs.

Call up the Memoscope SMPTE test image (press first the keys "CTRL" + "U", then "L").

Both monitors show the Memoscope SMPTE test image.

Enable the OSD menu on the TFT display.
Select the OSD menu "Settings", submenu "Ambient Light Compensation" and disable
the ambient light sensor (X)
Select the OSD menu ”Luminance”.
In the 100% field, set a luminance of 400 cd/m² +10 /-30 cd/m².
Select the OSD menu "Video Brightness", submenu "Man Brightness adj".
In the 0% field, set a luminance of 0.9 cd/m² +/- 0.1 cd/m² .
Select the OSD menu "Video Contrast", submenu "Man Contrast adj".
Select settings which are ensuring that all gray-scale values and – in addition – the 5%
and 95% fields are visible.
Select the OSD menu "Settings", submenu "Ambient Light Compensation" and re-enable
the ambient light sensor. (V)
Dim the ambient light sensor.
Dimming the ambient light sensor must result in the following luminance values:
In the 0% field: 0.5 cd/m² +/- 0.2 cd/m²
In the 100% field: 200 cd/m² +/- 30cd/m².
In he next step, save the settings (select "Exit" until the screen "Save Changes" appears.
Then, save the modifications with "Yes".
Perform the manual setting of the brightness and contrast of the second TFT display.
Visual check of the gray-scale graduations after the manual setting
On the Memoscope, select LUT 1 for both video outputs.
- The 5% and 95% fields must be clearly recognizable.
- Both TFT displays show an image with subjectively the same brightness.

Siemens AG SPR2-230.815.01 Page 13 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7 - 14 Monitor / Display Settings
Checks during timing in ”Stand-Alone” mode: 7

The monitor cart and the basic unit are not connected to each other.
The plug connection X10 is not plugged.
The monitor cart and its components are ready for operating.
Both TFT displays need to be checked.
• Call up the ”Memoscope User Setup”. Press simultaneously the keys "CTRL" + "U" on
the Memoscope keyboard.
Select the ”L” menu. The Memoscope SMPTE test image is indicated on both TFT
displays.

NOTE If the 3D PC image is indicated on the right monitor, press

simultaneously the keys "CTRL" + "D" on the Memoscope
keyboard to switch over to the Memoscope video signal.

On the Memoscope, select LUT 1 for both video outputs.

Visual check of the geometry

- The image position and the aspect ration need to be represented correctly.
The Memoscope SMPTE test image is neither cut nor represented too small.
Visual check of resolution
- In the Memoscope SMPTE test image in the center of the image shows clearly the fine
vertical and horizontal lines.
Visual check of shadings, artifacts and moiré patterns
- The gray-scale values are indicated without shadings.
- Neither artifacts nor moiré patterns are recognizable.
Visual check of the gray-scale graduations
- The 5% and 95% fields must be clearly recognizable.
- Both TFT displays show an image with subjectively the same brightness.

NOTE If you detect deviations of the brightness and contrast of the

displays, perform the steps described in section "Manual setting
of the brightness and contrast".

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 14 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Monitor / Display Settings 7 - 15
Check of the timing 3D reconstruction 7

The monitor cart and the basic unit are connected to each other.
The plug connection X10 is plugged.
The monitor cart and its components are ready for operating.
The 3D PC has correctly started up and is ready for operating.
The right TFT display needs to be checked.
• Press simultaneously the keys ”CTRL" + "D" on the Memoscope keyboard to switch over
to 3D Mode. The image of the 3D PC is indicated on the right display.
• On the 3D PC, select the menu "Options" - "Local Service".
• Call up the "Utilities" menu item.
• In the ”dropdown list ”Source”, select "Escape to OS".
• If not automatically pre-selected under "Command:" select "NT Command Interpreter".
• Insert the floppy disk "HTML Testimages VA00A", part number 75 58 567, into the
diskette drive.
• In the "Parameter" field, enter and start the command "a:\main.htm".
Select "ASPIA Testimage" and use this test image to check the settings.

Visual check of the geometry

- The image position and the aspect ration need to be represented correctly.
The ASPIA test image is neither cut nor represented too small.
Visual check of resolution
- In the center of the image and in the 4 corners of the ASPIA test image, the fine vertical
and horizontal lines are clearly visible.
Visual check of shadings, artifacts and moiré patterns
- The gray-scale values are indicated without shadings.
- Neither artifacts nor moiré patterns are recognizable.
Visual check of the gray-scale graduations

Siemens AG SPR2-230.815.01 Page 15 of 16 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
7 - 16 Monitor / Display Settings
- The 5% and 95% fields must be clearly recognizable.

NOTE If the 5% or 95% fields are only insufficiently recognizable, the

brightness and the contrast can be corrected.
(Select the OSD menu "Video Brightness", submenu "Man
Brightness adj"
and the OSD menu "Video Contrast", submenu "Man Contrast
adj").
The settings are saved for every individual video mode.
Do not modify the backlight setting (OSD menu "Luminance"),
since this would also affect
other video modes (default setting)!

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 16 of 16 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 8-1
Select “Options>>Local Service” in the window menu header.

• Enter the service key (6 characters in 2nd screen) in the Syngo SW screen that appears.
• Confirm the screen with “ok”.

Siemens AG SPR2-230.815.01 Page 1 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8-2 Syngo Configuration
The Service Home menu appears.

• Select “Configuration“.

NOTICE If problems occur during the following configurations, tests can

be initiated to uncover possible causes using the "DICOM Tests",
which can be accessed in the above Home menu.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8-3
The Selection menu appears.

• In the “list of system options“, the check boxes corresponding to the following table
must be selected accordingly.

Attached to network used

Modem Not used
Satellite Console Not used
DICOM print Should be selected if a hardcopy camera is used in the net-
work
DICOM offline no change
DICOM networking Should be selected if DICOM networking is used in the net-
work
DICOM HIS/RIS Should be selected if DICOM HIS/RIS is used in the network
Image import/export no change
Paper printer Not used
EPRI Not used

• In the footer: select “Next”.

Siemens AG SPR2-230.815.01 Page 3 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8-4 Syngo Configuration

NOTICE During initial installation, go through the screens in sequence.

With later supplements, the configuration steps that already have
entries can be skipped. However, these program screens must
also be checked or changed to reflect the on-site conditions.
The sequence of configuration steps should take place according
to the structure on the left side of the screens. To do this, each of
the underlined chapter names must be clicked.
All data should be entered as described in the configuration table.
In particular, upper and lower case conventions should be
observed!
The help text is available before each config screen. Advancing to
the next screen is possible by selecting the “>” symbol in the
footer.
Additional Online Help can be obtained by pressing the “Help”
button in the menu header.

NOTICE If the configuration is exited, this must ALWAYS be done by

selecting the “Home” button. The following illustration shows the
corresponding message. Otherwise the changes will NOT take
effect.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8-5

Customer and site 8

• The customer and site platform allows you to enter some general system and site-
specific information for easy identification of your machine.
• Select customer and site in the selection menu under local host.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
on-line description about the steps that then follow.

• Fill in the boxes accordingly.

- Handed over: time at which handover to the customer takes place
- Customer Name: should identify the station
- Customer Id: enter the customer number
- Product Name: SIREMOBIL Iso-C 3D
- Product No: is not used and is filled in with “0”
- Order No: SAP order number
- Serial No: Serial Number of the software package
(this entry indicates the SIREMOBIL Iso-C 3D and is important for the function)
- Maintenance Unit: ot
(to indicate this System as SIREMOBIL Iso-C 3D, this entry is important for the
function)
- Hospital: name of the clinic/hospital
- Street: street on which the clinic/hospital is located
- Street No: address

Siemens AG SPR2-230.815.01 Page 5 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8-6 Syngo Configuration
- Zip Code: postal code
- Phone No: telephone number of the clinic/hospital
- City: name of the city/town
- District: name of the district in which the clinic/hospital is located, corresponding to the
structure in the country organization
- Country: country

Local host 8

Site info 8

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8-7

NOTICE The following work steps describe integration of the SIREMOBIL

Iso-C 3D into an existing network.
After finishing the complete configuration, it is necessary to con-
figure SIREMOBIL Iso-C 3D at the corresponding modalities (Mag-
icView, Fluorospot, etc.).
The required steps are described in the instructions for the partic-
ular modalities.
To simplify this process, fill out the accompanying data sheet at
the end of these instructions and send it as a copy(-ies) to the
affected modalities. This page contains all relevant data to con-
figure SIREMOBIL Iso-C 3D at these modalities.

TCP/IP LAN settings 8

The TCP/IP LAN platform allows you to configure the local networking properties of your
system. Skip this section if your system works completely as a stand-alone system, the
default values provided will do in that case.
• When selected, the installation procedure runs automatically to the point TCP/IP LAN.
If there are later additions and changes, manually select the appropriate point in the
selection menu, on the left under local host.

Siemens AG SPR2-230.815.01 Page 7 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8-8 Syngo Configuration
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Select the “Computer name“ in the configuration table and enter it.

NOTICE The computer name (= host name) should be changed only once,
at the beginning of the configuration. If the computer name is
changed later there can be problems.

NOTICE The computer name (host name) must not be longer than 10 char-
acters in length. Please use only lowercase letters if possible for
the host name.

• "Obtain an IP address from DHCP server " must not be selected.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 8 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8-9
User settings 8

The user settings are not changed.

Users 8

Siemens AG SPR2-230.815.01 Page 9 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 10 Syngo Configuration
Monitor type 8

• Select "color".
• Select "Siemens (True Color").
• Select "save".

Service 8

Mail 8

• Not used.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 10 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 11

Siemens AG SPR2-230.815.01 Page 11 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 12 Syngo Configuration
FTP 8

• Not used.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 12 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 13
Autotransfer 8

• Not changed.

Siemens AG SPR2-230.815.01 Page 13 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 14 Syngo Configuration
Eventlog settings 8

The installation procedure runs automatically to the point Eventlog. If there are later addi-
tions and changes, manually select the appropriate point in the selection menu on the left
under service.
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

The Eventlog function allows customizing of the Event Log user interface of your Service
Software. Specify whether:
only service-relevant messages should be logged
only service-relevant messages should be displayed in the Event Log window (with all
errors being logged) and the sequence number should be displayed.
• Unless otherwise specified, select all 3 check boxes.
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 14 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 15
Backup & Restore settings 8

The installation procedure runs automatically up to the point backup & restore. If there are
later additions and changes, manually select the appropriate point in the selection menu,
on the left under service.
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Backup/Restore allows you to specify the data to be saved and restored when executing
the Backup & Restore function of your Service Software.
• The preset packages are sufficient here and should therefore not be changed.
• Select “Next or Finish” in the menu footer.

Siemens AG SPR2-230.815.01 Page 15 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 16 Syngo Configuration
Licensing 8

The installation procedure runs automatically up to the point Licensing. If there are later
additions or changes, manually select the appropriate point in the selection menu, on the
left under service.
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Insert the diskette with the license file.

• Use the "Browse..." button in the configuration window to select < a:\......license.dat >.
• Click "Import Licensefile".
• Select "Save" in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.
• Remove the diskette.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 16 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 17

DICOM 8

General 8

The installation procedure runs automatically up to the point local AE. If there are later
additions or changes, manually select the appropriate point in the selection menu
(see Chapter 9).
The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

MERGE_PRINT_SCU

• Take the data from the configuration table. The AET names must be unique in the
network. They will be automatically set by changing the host name in the TCP/IP LAN
settings dialog.

NOTICE All AEs should start with uppercase letters. This is required for
the functionality of the DICOM tests (e.g. verification).

• Leave HIS/RIS unchanged, since it is not relevant.

• Enter Study Transfer (e.g. AN_SIREMOBIL Iso-C 3D) or if not otherwise defined take
over the title given by the system.
• Enter Print AET or MERGE_PRINT_SCU.

Siemens AG SPR2-230.815.01 Page 17 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 18 Syngo Configuration

NOTICE The Print AET is required to distinguish between the different

modalities sending images to the printer.
Thus the correct LUT can be selected.
If the wrong AET is configured a default LUT might be selected in
the printer, which has a big impact on the image quality!

• Select "Save" in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.

Character settings 8

• The installation procedure runs automatically up to the point character set.

• These settings must not be changed.

ISO_IR 100

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 18 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 19
Offline device settings 8

When selected, the installation procedure runs automatically up to the point offline
devices. If there are later additions or changes, manually select the appropriate point in
the selection menu, on the left under DICOM.
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• In this section, you define the Setting of DICOM archive devices on the local host.
• Enter a logical name for the patient browser or viewer Transfer/Import-Export To menu
with archive targets (e.g. CD_ROM_1).
• Select the drive type.

NOTICE Do not select "Floppy" as archive devices.

• Set the "CD-RW drive", "recording speed" to 8.

• If there is a MOD device, enter the drive by selecting the SCSI address (port/bus/target
id) and manufacturer device information
• Select the file system FAT. Do not select SPI file system (not released yet)
• Select only the drive letter c:

Siemens AG SPR2-230.815.01 Page 19 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 20 Syngo Configuration
• Only available drive letters are displayed in the selection box, manufacturer information
is displayed for SCSI devices.
• Select "Save" in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Repeat this procedure for all devices (CD-R, MOD) as appropriate.
• Select “Next or Finish” in the menu footer.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 20 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 21
Network node settings 8

NOTE 3D Navigation requires a special syntax "N_" for name

designations. Example: N_Navi1 in the "edit Name" field.

NOTE To ensure that the network nodes are accepted, the system must
be switched on and off at the end of the configuration at the
latest.

When selected, the procedure runs automatically up to the point network nodes. If there
are later additions and changes, manually select the point in the selection menu, on the
left under DICOM.
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Definition of network nodes witch are connected to SIREMOBIL Iso-C 3D.

• Select “define new“ (with a new installation) or accept the entry (with components that
are already configured).
• In “Host Name“, enter the name of the 1st application (e.g. Magic View).
If a name server is used, and the 1st application is configured in the network, it can be
searched for using “FIND“.
The response should be: “Host <name> is sussessfully resolved”.
• Confirm with “ok”.
- The IP address will then be accepted.
• Select “connected by LAN“.

Siemens AG SPR2-230.815.01 Page 21 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 22 Syngo Configuration
• Select TEST. The TEST command corresponds to a PING command.
- The response should be: “Host with IP address xxx.xxx.xxx.xxx is alive”.
• Accept the entry with “Save” in the footer.
• Acknowledge the message “...successfully saved” with “ok”.
• If there is no entry, enter a “Host Name” for the 1st entry and “IP address” (take the
data from the configuration table).
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “define new“ again or accept the next entry.
• Repeat the steps described above as often as necessary until all network nodes are
entered.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow. The "DICOM network nodes" next
menu”appears.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 22 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 23
Here, the remaining data for the previously entered host are supplemented.

NOTICE Here, only stations and systems should be entered that support
the services: Storage SCP or query/retrieve
or if there are syngo-based stations.
If stations with ONLY Storage SCU at the network nodes are
entered, these appear incorrectly in the user interface in the list of
transmit destinations.

• Enter the “AE Title” and the “Port-Number” of the AET (take the information from the
Site Table).

NOTICE All AEs should start with upper-case letters. This is required for
the function of the DICOM tests (e.g. verification).

• At Select Logical name, select “define new” or accept the entry.

• At Logical name, enter the clear text names for application 1 as it is to be displayed later
on the user interface.
• Select Syngo-based if this application is Syngo-based.
• In “Host selection”, select the appropriate network nodes.
• In “Default Node”, select the appropriate default. The sequence “first default“,
“second default” or “no default” is set. This setting is defined as which application is to
be selected as the default.
• In “Select AE Title”, if already configured, select the appropriate “AE-Title” or enter the
AE title (e.g. 049SA1DC53DRSP) and Port Number of application 1 (e.g. 50082) (take
the information from the Site Table).
• Select the Image Transfer(Store), QUERY and/or RETRIEVE check boxes
appropriately to match the possibilities of the modality.
• Only formats supported by the stations (e.g. Implicit little endian...) should be selected,
i.e., highlighted in blue.
Select "Compression" only if the other station supports "Compression". In case of doubt
look up or try out in the DICOM Conformant Statement!

NOTICE Do not use JPEG Lossy Compression!

• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• The connection can be tested using the “Verification” button. The TEST command
corresponds to a C-Echo command. If the test is successful, the message “...is
responsing” appears.
• If there are different AET’s defined for Storage, Query and Retrieve for individual
modalities, they should each be entered with a new entry with different logical names.
• Repeat this procedure as often as needed until all network components, even for
different AE titles, have been entered.

Siemens AG SPR2-230.815.01 Page 23 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 24 Syngo Configuration
• Select “Next or Finish” in the menu footer.

Print device settings 8

• When selected, the installation procedure runs automatically to the point print devices.
If there are later additions and changes, manually select the appropriate point, on the left
under DICOM.

Configuration of hardcopy devices. Here you define the laser cameras and printers, that
are connected to your system.
• At “Select Host“, select “define new” or the configured camera.
• In “Host Name”, accept <Network Name> or enter a name.
• Select “connected by LAN”.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 24 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 25
• If a name server is used and the application is configured in the network, you can search
for it with FIND.
• Select FIND.
- The following message should appear:
Host <Name> is successfully resolved. The IP address is then accepted.
• Using the “Test” button, attempt to reach the network component just configured.
The TEST command corresponds to a PING command.
- If the test is successful, the message “...is alive” appears.
- If the test is not successful, the message “...is not alive” appears.
A comparison of the entries for the network components and those that have been
completed must then be made.
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Repeat the procedure as often as required until all cameras being used are entered.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow. The “DICOM hardcopy device next
menu“ appears.

Siemens AG SPR2-230.815.01 Page 25 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 26 Syngo Configuration
• Take the information from the Site Table.
Here, the remaining data for the previously entered host is supplemented.
• Enter the “AE Title” and the “Port Number” of the AET.
• In “Selecet Logical Name” select “define new” or accept the entry.
• In “Logical Name”, enter the clear text name for the HCC (e.g. Printer).
• In “Host selection”, select the corresponding name of the camera (e.g. Agfa).
• In “Select AE Title”, if already configured, select the appropriate AE title (e.g. AGFA01)
or select “define new”.
• Accept the “AE Title” or enter one (e.g. AGFA01).
• Accept the “Port Number” or enter one (e.g.104).

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 26 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 27
• Using the “Test” button, attempt to reach the network component just configured.
The TEST command corresponds to a C-Echo command.
- If the test is successful, the message “...is responding” appears.
- If the test is not successful, the message “...is not responding” appears.
A comparison of the entries for the network components and the entries that have been
made is then necessary
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Repeat the procedure as often as required until all cameras being used are configured.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow. The “DICOM hardcopy device next
menu“ appears.

• Entering the Camera Data.

• In "Type" select "DICOM printer".
• In "DICOM Node" select the configured HCC.
• In "Class" select the Camera name.
• At "HC Device" enter the clear text name for HCC as it displayed later on the user
interface.
• At "Medium type" select the used medium.
• At "Film destination" select the used destination.

Siemens AG SPR2-230.815.01 Page 27 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 28 Syngo Configuration
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Repeat the procedure as often as required until all cameras being used are configured.
• Select “Next or Finish” in the menu footer.

Hardcopy overview 8

• When selected, the installation procedure runs automatically up to the point hc overview.
If there are later additions or changes, manually select the appropriate point in the
selection menu, on the left under DICOM.

Modification and test capability of the previously entered data 8

• Using the “Test” button, attempt to reach the network component just configured.
The network access TEST command corresponds to a PING command.
The DICOM access TEST command corresponds to a C-Echo command.
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 28 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 29
LUT file settings 8

• When HCC is selected, the installation procedure runs automatically up to the point LUT
files. If there are later additions or changes, manually select the appropriate point in the
selection menu, on the left under DICOM.

Siemens AG SPR2-230.815.01 Page 29 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 30 Syngo Configuration

• In order to set Filming, a new LUT must be loaded and set for the XA characteristic
curve. This is stored on the hard disk.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow.
The “DICOM LUT files next menu" appears.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 30 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 31

• Select the LUTs for the following "Image types":

Image type LUT Max. Density

XAImage xa 3.00
CTImage

• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.

Siemens AG SPR2-230.815.01 Page 31 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 32 Syngo Configuration
HIS/RIS nodes 8

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 32 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 33
• If the test is not successful, the message “...is not alive” appears.
A comparison of the entries in the network components and the entries made must then
be made.
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Repeat the procedure as often as required until all hosts have been entered.
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow. The “Next menu“ appears.

Here, it is defined whether the import/export directory is connected locally or through the
network.

Siemens AG SPR2-230.815.01 Page 33 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 34 Syngo Configuration
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that follow. The next page appears.
• Select "define new" under "Select Logical HD drive".
• Under "Logical Name" enter "Disk_Drive_A".
• Select the radio button "Local system".
• Under "Path" enter "A:\".
• Under "Drive" enter "A:\".
• Click on the "create" button.
• Select “Save” in the footer to save the values that were entered.
• Acknowledge the message “...successfully saved” with “ok”.
• Select “Next or Finish” in the menu footer.

NOTE If additional local or remote systems need to be activated, select

this page again and enter the necessary dates.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 34 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 35
Patient registration settings 8

Viewer settings 8

Siemens AG SPR2-230.815.01 Page 35 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 36 Syngo Configuration
CorRea settings 8

MPPS settings 8

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 36 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Syngo Configuration 8 - 37
Worklist result settings 8

Siemens AG SPR2-230.815.01 Page 37 of 38 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
8 - 38 Syngo Configuration
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 38 of 38 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
3D Limiting Resolution and Calibration 9 9-1

Without 3D Navigation 9

• First perform the calibration and then the 3D limiting resolution.

See: "Image Quality Quick Test SIREMOBIL Iso-C".
• Continue as described in the chapter "Syngo Configuration".

With 3D Navigation 9

NOTE Observe chapters 1 und 2.

3D Navigation option is enabled 9

If the 3D Navigation option is already installed and enabled on the system, carry out the
following steps.
• First perform the 3D limiting resolution. If it conforms to the specification, no calibration is
required.
See: "Image Quality Quick Test SIREMOBIL Iso-C".
• Continue as described in the chapter "Syngo Configuration".

3D Navigation option is not enabled 9

If the 3D Navigation option is not yet installed on the system, perform the following steps.
• Secure the patient data and SW settings 02 (network configuration data) as described in
the chapter "Backup/ Restore". If necessary, note down any other configuration data.
• Install the 3D software as described in the chapter "3D Software".
• Load the control software as described in the chapter "Downloading the Control
Software".
• Of the SW settings 02, restore the following groups via Restore as described in the
chapter "Backup/Restore":
Service \TCPIP\LAN-Settings
Service \TCPIP\RAS-Setting
Service \DICOM\HISRISNodes
Service \DICOM\LUTFiles
Service \DICOM\Print Devices
Service \DICOM\NetworkNodes
Service \DICOM\General
Service \LocalHost\SiteInfo

If necessary, enter any other configuration data manually.

• Perform the mechanical settings as described in the chapter "Mechanical Settings".
• Set the monitor as described in the chapter "Monitor Settings".
• Configure the network nodes as described in the chapter "Syngo Configuration".
Observe the syntax "N_" .
• Perform the calibration and then the 3D limiting resolution.
See: "Image Quality Quick Test SIREMOBIL Iso-C"

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
9-2 3D Limiting Resolution and Calibration
• Check the overall accuracy of the 3D Navigation with the test body.
See: "Image Quality Quick Test SIREMOBIL Iso-C".
• Continue as described in the chapter "Syngo Configuration".

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Customer Settings 10 10 - 1

General remarks 10

Customer-specific settings can be made using the "Configuration..." function.

• From the Viewer Interface select "<Options> <Configuration...>"
The following window appears:

Setting the desired user interface language (normally done

during installation) 10

• Double-click "Regional Settings".

• Select the desired language here and confirm with "OK".

Siemens AG SPR2-230.815.01 Page 1 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
10 - 2 Customer Settings
• Confirm the prompt for a restart with "OK" to accept the settings.

Setting the country-specific keyboard layout (normally done

during installation) 10

• From the Viewer Interface select "<Options> <Configuration...>".

• Double-click "Regional Settings".

• Select "Input Locales".

• Double-click the selection used.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Customer Settings 10 - 3

A selection can be made between the English, German and French keyboard lay-
out.
• Select the layout that corresponds to the keyboard that has been shipped in "Keyboard
layout".
• Click "OK".
• Click "OK".

Printing on a video printer with Syngo 10

If the image quality of the printouts printed via Syngo on the video printer is insufficient, it
may be possible to improve the quality by changing the relevant parameters.
• Select Utilities.

• Under "Source", select the item "Unlock System key".

• Select "OK".
• Press the "CTRL" + "ESC" keys.
• Press the "Enter" key.

Siemens AG SPR2-230.815.01 Page 3 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
10 - 4 Customer Settings
ê The Windows "Start" button appears.

• Select "Start".
• Select "Programs".
• Select "Matrox Power Desk NT".
• Select"Matrix Display Properties".
• Select the "Monitor" tab.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Customer Settings 10 - 5
• Select "Current display" 2 and "Advanced TV Settings...".

• Change the brightness and contrast values and try to find the optimal setting by making
test prints.

Siemens AG SPR2-230.815.01 Page 5 of 6 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
10 - 6 Customer Settings

Other customer-specific settings 10

The settings for other functions should be straight forward and are therefore not described
separately here.
Help for these functions can be found in the operating instructions.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 6 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Function Test in the Network 11 11 - 1

NOTICE Prerequisite for the function test is that the Siremobil Iso-C 3D
has been properly entered in all corresponding modalities.
The required steps are described in the instructions for the corre-
sponding modalities. All required information regarding this can
be taken from the accompanying sheet.

The following functions should be checked:

NOTICE Images must be sent from the Siremobil Iso-C 3D to the particular
connected modality and from the connected modality to the
Siremobil Iso-C 3D.

Check point yes no

• Are all elements correctly displayed?
• Is the directory structure (in the browser) with numbers, series and studies
retained?
• Are annotations and overlays retained?
• Are the special functions of the DR viewer functioning properly, even with
images from non-Siemens products?

NOTICE If one of these points is answered with “no”, further action

regarding correcting the error must be discussed with the
responsible USC/HSC.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
11 - 2 Function Test in the Network
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 12 - 1

Backup 12

NOTE Only use CD-Rs, since CD-RWs may be incompatible with Syngo.

General remarks 12

• A backup from system-specific tables, similar to tuneup tables or customer specific

configuration entries, is always necessary after software updates or system adjustment
steps.
• From the Syngo User Interface, please select “Options>>Local Service” in the window
menu header..

• Enter the service key ( 6 characters in 2nd mask).

• Confirm with <OK>.

Siemens AG SPR2-230.815.01 Page 1 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 2 Backup / Restore
The Service Home menu appears.

• Have blank CDs/diskettes ready.

• Select “Backup & Restore”
• Insert the backup CD / diskette.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 - 3
The following window appears:

• In the “Command” selection menu, select “Backup”.

• Select the corresponding storage medium, CD or diskette, under "Drives".
• The corresponding package is selected in “Packages” and saved with “Go”.
• Select the Package "SW Settings" and save with "GO".
• Wait until the "Ready" message appears in the footer.
• Select thethe Package "User Settings" and save with "GO".
• Wait until "Ready" message appears in the footer.

NOTICE If subsequent changes, e.g. in the configuration, need to be

made, the corresponding backup package must be saved again.

NOTICE With a backup of the "SW Settings", the "TCP/IP LAN", "DB ID Off-
set" and "Backup/Restore" data are not saved. In other words,
they must be noted.

• Exit the window with “Home”.

• Remove the backup CD / diskette from the drive.

Siemens AG SPR2-230.815.01 Page 3 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 4 Backup / Restore

Restore 12

• From the Syngo User Interface, please select “Options>>Local Service” in the window
menu header.

• Enter the service key (6 characters in 2nd mask).

• Confirm with <OK>.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 4 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 - 5
The Service Home menu appears.

• Select “Backup & Restore”.

• Insert the backup CD / diskette.
• Select "Restore" in the “Command” selection menu.
• Select the "Drive" in which you have inserted the backup CD / diskette.

Siemens AG SPR2-230.815.01 Page 5 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 6 Backup / Restore
Restore SW settings 12

• In “Archives”, select the correct (latest) SW settings backup file.

• Mark all files in "Groups", i.e. highlighted in blue (with Ctrl or Shift +left Mouse).
• The restore routine is started with “Go”.
• Wait until the "Ready" message appears in the footer. This takes a few minutes.
• Exit the window with “Home” or go to Restore User Settings.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 6 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 - 7
Restore user settings 12

• In “Archives”, select the correct (latest) User Settings backup file.

• Mark all files in "Groups", i.e. highlighted in blue (with Ctrl or Shift +left Mouse).
• The restore routine is started with “Go”.
• The WS initiates a restart.
• Remove the backup CD / diskette from the drive.

NOTICE With a restore of the "SW Settings", the "TCP/IP LAN", "DB ID Off-
set" and "Backup/Restore" data are not restored. In other words,
this information must be reentered manually.

Siemens AG SPR2-230.815.01 Page 7 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 8 Backup / Restore
Manual SW settings 12

• Select “Configuration“ in the Home menu.

The Selection menu appears.

• In the footer: select “Next”.

• Skip the next screen with "Next".
• The installation procedure runs automatically to the point TCP/IP LAN.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 8 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 - 9
• The next screen appears by clicking “>“ in the footer. The pages that appear provide an
online description about the steps that now follow.

• Find the “Computer name“ in the configuration table and enter it.
• Select the radio button: “Specify an IP address” unless otherwise indicated.
• Take the IP addresses from the configuration table and enter them.
• Delete any previously entered IP addresses.
• If certain components are not configured (Gateways, DNS or WINS), any entries that are
in these screens should be deleted.
The corresponding check boxes should then be deselected.
• Select the “Enable LMHOSTS Lookup” check box.
• Select the “Enable DNS for Windows Resolution” check box only if WINS servers are
configured.
• Select “Save” in the footer to save the values that have been entered.
• Acknowledge the messages “.... after reboot” with “ok”.
• Acknowledge the messages “.... successfully saved” with “ok”.
• Select “Next” in the menu footer.
• The installation procedure runs automatically to the point DB ID Offset.

Siemens AG SPR2-230.815.01 Page 9 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 10 Backup / Restore
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Leave the Index unchanged at “0”.

• Select “Next” in the menu footer.
• The installation procedure runs automatically up to the point Backup & Restore.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 10 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Backup / Restore 12 - 11
• The next screen appears by clicking “>“in the footer. The pages that appear provide an
online description about the steps that follow.

• Backup/Restore allows you to specify the data to be saved and restored when executing
the Backup & Restore function of your service software.
• The preset packages are sufficient here and should therefore not be changed.
• Select “Next or Finish” in the menu footer.
• Exit the window with “Home”
Confirm the request to reboot with "OK".

Siemens AG SPR2-230.815.01 Page 11 of 12 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
12 - 12 Backup / Restore
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 12 of 12 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Notes on Backup and Restore 13 13 - 1
System-specific tables, such as tuneup tables and customer-specific configuration
entries, have to be backed up (and restored) when updating the software or when modify-
ing system parameter.
1. The regional settings, date & time, keyboard and language are not contained in
the backup set. Consequently, the configuration of regional settings has to be
executed after each software installation.
2. When using a MOD for backup, note that in the application the MOD media can
only be ejected within the ArchNet functionality or the patient browser.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
13 - 2 Notes on Backup and Restore
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Data table for connected Stations 14 14 - 1

Station 14

NOTICE This page serves as a memo for registering the WS to all

connected modalities. Here, the most important information that
is needed to assure image transfer at the DICOM level is
summarized.
The table must be filled out and made available as a copy to the
service personnel for the other modalities as information for the
installation.

Siremobil Iso-C 3D Data Parameter Remarks

Host name
IP address
DICOM storage SCP and SCU
DICOM print SCU
AE title for storage
AE title for print
Port for storage 104
Port for print 104
Supported DICOM services:
Image Transfer (Store) yes
Query yes
Retrieve yes
Supported transfer syntax
Implicit little endian yes
Explicit little endian yes
Explicit big endian yes
Supported compression
JPEG Lossy not recommended
JPEG Lossless yes
Syngo-based system yes
Supported IOD´S see conformance State-
ment

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
14 - 2 Data table for connected Stations
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Final Work Steps 15 15 - 1

Final work steps 15

• Close all covers. Watch the ground wire connections when doing so.
• Perform the Image Quality Quick Test (refer to the SIREMOBIL logbook).
• Perform the protective conductor test in accordance with ARTD - 002.731.17.
The protective conductor resistance must be <= 0.2 ohms.
• File the instructions in the System Binder or System Logbook.
• After completing the configuration, the following information must be reported to the USC
management system:
¹ Dongle ID
¹ PC identification number
Responsible ITC call center (hardware service) in the particular country. Refer to the list
enclosed with the PC for this information.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
15 - 2 Final Work Steps
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions
Changes to previous version 16 16 - 1

Chap. 0 Cover sheet, revision level and table of contents generated again

Chap. 1 to 16 Revision level increased

Chap. 1 Necessary documents supplemented

Necessary measuring equipment updated
Chap. 3 Programming "Enable Bridge" added.

Chap. 4 Note for published patches added.

Chap. 7 Adjustment for TFT monitors supplemented

Chap. 8 Programming CD-RW recording speed added.

Programming Disk Drive A added.

Siemens AG SPR2-230.815.01 Page 1 of 2 SIREMOBIL Iso-C 3D

Medical Solutions Rev. 05 10.04 CS PS 24 System
16 - 2 Changes to previous version
This page intentionally left blank.

SIREMOBIL Iso-C 3D SPR2-230.815.01 Page 2 of 2 Siemens AG

System Rev. 05 10.04 CS PS 24 Medical Solutions