GRUNDFOS INSTRUCTIONS

CREC, CRIEC, CRNEC, MTREC, CMEC

Supplement to Installation and Operating Instructions
General information
These installation and operating instructions are a supplement to the installation
and operating instructions manual for standard CREC, CRIEC, MTREC, CMEC
pumps.
(Publication No. 99955183 and 92564852)

This supplement is valid for 3 x 200-240V motor

For use in APAC only

2
CREC, CRIEC, CRNEC, MTREC, CMEC

Table of contents
English (GB)
Addendum to 7.2 (Cable Requirements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Addendum to 7.3 (Mains Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Addendum to 7.5 (Connection Terminals)
(i) for 1.1kW to 1.5kW models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
(ii) for 2.2kW to 3kW models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Addendum to 8.1 (Maximum number of starts and stops) . . . . . . . . . . . . . . . . 10
Addendum to 8.2 (Ambient Temperature). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Addendum to 10 (Basic Operating Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Addendum to 11 (Menu overview)
(i) Grundfos GO Remote for 1.1kW to 1.5kW models . . . . . . . . . . . . . . 12
(ii) Grundfos GO for 2.2kW to 3kW models . . . . . . . . . . . . . . . . . . . . . 15
Addendum to 12.25 (Predefined Setpoints) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3
 7.2 Cable requirements
English (GB)

7.2.1 Cable cross-section

DANGER
Electric shock
Death or serious personal injury
- Always comply with local regulations as

TM05 3495 1512

to cable cross-sections.
3 x 200-240 V

Cross section
Power Conductor
[kW] type
[mm2] [AWG] Fig. 5 Mains connection, three-phase motors
Solid 1.5 - 10 16-8
0.25 - 2.2
Stranded 1.5 - 10 16-8
Solid 2.5 - 10 14-8
3.0 - 5.5
Stranded 2.5 - 10 14-8

7.3 Mains supply

DANGER
Electric shock
Death or serious personal injury
- Use the recommended fuse size. See
section 22. Technical data, three-phase
motors.

7.3.1 Three-phase supply voltage

Three-phase motors are available for the voltages
below:
• 3 x 200-240 V - 10 %/+ 10 %, 50/60 Hz, PE
Check that the supply voltage and frequency
correspond to the values stated on the nameplate.
The wires in the motor terminal box must be as short
as possible. Excepted from this is the separated
protective-earth conductor which must be so long
that it is the last one to be disconnected in case the
cable is inadvertently pulled out of the cable entry.
In order to avoid loose connections, make sure that
you have pressed home the terminal block for L1, L2
and L3 in its socket when you connect the supply
cable.
For maximum backup fuse, see section
22. Technical data, three-phase motors.

Motors cannot be supplied through an IT

network.

RCD,
type B
TM05 3942 1812

L1 L1
L2 L2
L3 L3
PE

Fig. 4 Example of a mains-connected motor

with main switch, backup fuses and
additional protection
4
7.5 Connection terminals (for 1.1kW to 1.5kW models)
The descriptions and terminal overviews in this section apply to
three-phase motors.
For maximum torques, see section Torques, page 34.

English (GB)
7.5.1 Connection terminals
The pump has these connections:

• one analog input

• three digital input
• two signal relay output
• GENIbus connection.

Digital input 1 is factory-set to be start-stop

input where open circuit results in stop. A
jumper has been factory-fitted between
terminals 2 and 6. Remove the jumper if
digital input 1 is to be used as external
start-stop or any other external function.

DANGER
Electric shock
Death or serious personal injury
- Make sure that the wires to be
connected to the connection groups
below are separated from each other by
reinforced insulation in their entire
lengths.

• Inputs and outputs

All inputs and outputs are internally separated from
the mains-conducting parts by reinforced insulation
and galvanically separated from other circuits. All
control terminals are supplied by protective extra-low
voltage (PELV), thus ensuring protection against
electric shock.
• Signal relay output
– Signal relay 1 and 2:
LIVE:
You can connect supply voltages up to 250
VAC to the output.
PELV:
The output is galvanically separated from
other circuits. Therefore, you can connect the
supply voltage or protective extra-low voltage
to the output as desired.
• Mains supply (terminals N, PE, L or L1, L2, L3,
PE).

5
 Terminal Type Function
English (GB)

Normally
NC
closed contact
Signal relay 1
C1 Common
(LIVE or PELV)
Normally open
NO
contact
Normally
NC
closed contact
Signal relay 2
C1 Common
(LIVE or PELV)
NC Normally open
NO
C1 contact
NO

NC 9 GND Ground
C2
Digital input,
NO 1 DI2
configurable
9 GND
Digital input,
1 DI2 10 DI3
+24 V*
OC
GND
DI configurable
10 DI3/OC1
4 AI1 Analog input:
+24 V* +24 V* +24 V*/5 V* 2 DI1 0-20 mA / 4-20 mA
+ + 4 AI1
5 +5 V 0.5 - 3.5 V / 0-5 V /
6 GND 0-10 V
A GENIbus A
Digital input,
Y GENIbus Y 2 DI1
B GENIbus B
configurable
3 GND Supply to
15 +24 V 5 +5 V potentiometer and
8 +24 V sensor
26 +5 V
23 GND
6 GND Ground
A GENIbus, A GENIbus, A (+)
* If you use an external supply source, there must
Y GENIbus, Y GENIbus, GND
be a connection to GND.
B GENIbus, B GENIbus, B (-)
Fig. 6 Connection terminals
3 GND Ground
15 +24 V Supply
8 +24 V Supply
Supply to
26 +5 V potentiometer and
sensor
23 GND Ground

6
7.5 Connection terminals (for 2.2 kW to 3 kW models)
The descriptions and terminal overviews in this section apply to
three-phase motors.
For maximum torques, see section Torques, page 34.

English (GB)
7.5.1 Connection terminals
The pump has these connections:

• one analog input • Bluetooth (BLE) connection

• three digital input
• two signal relay output
• GENIbus connection.

Digital input 1 is factory-set to be start-stop

input where open circuit results in stop. A
jumper has been factory-fitted between
terminals DI1 and GND. Remove the
jumper if digital input 1 is to be used as
external start-stop or any other external
function.

DANGER
Electric shock
Death or serious personal injury
- Make sure that the wires to be
connected to the connection groups below
are separated from each other by
reinforced insulation in their entire
lengths.
• Inputs and outputs
The inputs and outputs are internally separated
from the power supply-conducting parts by
reinforced insulation
and galvanically separated from other circuits. All
control terminals are supplied with safety extra-low
voltage
(SELV), ensuring protection against electric shock.
Cables for the relays must be double insulated or
reinforced and rated at least 250V/2A.

• Signal relay output

– Signal relay 1 and 2:
LIVE:
You can connect supply voltages up to 250
VAC to the output.
SELV:
The output is galvanically separated from
other circuits. Therefore, you can connect the
supply voltage or protective extra-low voltage
to the output as desired.
• Mains supply (terminals N, PE, L or L1, L2, L3,
PE).

7
English (GB)

NC C1 NO NC C2 NO DI3 24V 5V

5V A Y B AI1 DI1 24V DI2

TM082862
* If you use an external supply source, there mustbe a connection to GND.

Fig. 6 Connection terminals

Terminal Type Function

NC Normally closed contact
C1 Common Signal relay 1: LIVE or SELV
NO Normally open contact
NC Normally closed contact
C2 Common Signal relay 2: SELV only
NO Normally open contact
GND GND Signal ground
Digital input/output, configurable
DI3 DI3/OC1
Open collector: Maximum 24 V resistive or inductive
24V +24 V Power supply
5V +5 V Power supply to a potentiometer or sensor
GND GND Signal ground

8
Terminal Type Function

English (GB)
5V +5 V Power supply to a potentiometer or sensor
A GENIbus, A GENIbus, A (+) / Modbus, D1 (+)
Y GENIbus, Y GENIbus, GND / Modbus, GND
B GENIbus, B GENIbus, B (-) / Modbus, D0 (-)
Analog input:
AI1 AI1 • 0-20 mA or 4-20 mA
• 0.5 - 3.5 V, 0-5 V or 0-10 V.
Digital input, configurable

Digital input 1 is factory-set to be start or

stop input where an open circuit results in
DI1 DI1 stop. A jumper has been factory-fitted
between terminals DI1 and GND. Remove
the jumper if digital input 1 is to be used as
external start or stop or any other external
function.

24V +24 V Power supply

GND GND Signal ground
GND GND Signal ground
DI2 DI2 Digital input, configurable

9
 8. Operating conditions
English (GB)

8.1 Maximum number of starts and stops

The number of starts and stops via the power supply
must not exceed four times per hour.
When switched on via the power supply, the pump
starts after approximately 5 seconds.
If a higher number of starts and stops is desired, use
the input for external start-stop when
starting/stopping the pump.
When started via an external on/off switch, the pump
starts immediately.

8.2 Ambient temperature

8.2.1 Ambient temperature during storage and
transportation
Minimum: -30 °C
Maximum: 60 °C.
8.2.2 Ambient temperature during operation

3 x 200-240 V

Minimum -20 °C
Maximum 40 °C

The motor can operate with the rated power output

(P2) at 40 °C, but continuous operation at higher
temperatures reduces the expected product life.

10
10. Basic operating panel

English (GB)
The pumps are fitted with this operating panel as standard.

TM082922
Pos. Symbol Description

1 Grundfos Eye: The indicator light shows the operating status of the product.

Communication:
2
The button enables communication with Grundfos GO and other products of the same type.

11
 11. Grundfos GO Remote 11.1 Communication
English (GB)

(For 1.1kW to 1.5kW models) When Grundfos GO Remote initiates communication

with the pump, the indicator light in the middle of
The pump is designed for wireless radio or infrared
Grundfos Eye flashes green. See section
communication with Grundfos GO Remote.
15. Grundfos Eye.
Grundfos GO Remote enables setting of functions
Establish communication using one of these
and gives access to status overviews, technical
communication types:
product information and actual operating
parameters. • radio communication
Grundfos GO Remote offers the following mobile • infrared communication.
interfaces (MI). 11.1.1 Radio communication
Radio communication can take place at distances up
to 30 m. The first time Grundfos GO Remote
communicates with the pump, you must enable
communication by pressing or on the pump
operating panel. Later when communication takes
place, the pump is recognised by Grundfos GO
Remote and you can select the pump from the "List"
menu.
1
11.1.2 Infrared communication
TM06 6256 0916

When communicating via infrared light, Grundfos GO

+ Remote must be pointed at the pump operating
panel.
11.1.3 Startup guide
The first time Grundfos GO Remote communicates
Fig. 13 Grundfos GO Remote communicating with the pump, the startup guide starts to guide you
with the pump via radio or infrared through the settings needed for the product to
connection (IR) operate in the given application. When the startup
guide has been completed, the pump is ready for
operation.
Pos. Description

Grundfos MI 301:
Separate module enabling radio or infrared
1 communication. You can use the module in
conjunction with an Android or iOS-based
smart device with Bluetooth connection.

12
11.2 Menu overview for Grundfos GO Remote (for 1.1kW to 1.5kW models)

CMEC, CREC,
Dashboard CRIEC, CRNEC,

English (GB)
MTREC

CMEC, CREC,
"Status" CRIEC, CRNEC,
MTREC

"Resulting setpoint" ●
"Actual controlled value" ●
"Motor speed" ●
"Power consumption" ●
"Energy consumption" ●
"Operating hours" ●
"Analog input 1" ●
"Digital input 1" ●
"Digital input 2" ●
"Digital input 3" ●
"Fitted modules" ●

13
 CMEC, CREC,
English (GB)

"Settings" CRIEC, CRNEC, Section Page

MTREC

"Setpoint" ● 12.1 Setpoint 17

"Operating mode" ● 12.2 Operating mode 17
"Set user-defined speed" ● 12.4 "Set user-defined speed" 17
"Control mode" ● 12.5 "Control mode" 17
12.11 "Stop function" (Low-flow stop
"Stop function" ● 22
function)
"Controller" ● "Controller" (Controller settings) 20
"Operating range" ● 12.9 Operating range 21
"Ramps" ● 12.12 Ramps 24
"Number" ● 12.14 ""Number" (Pump number) 24
12.15 "Radio communication"
"Radio communication" ● 24
(Enable/disable radio comm.)
"Analog input 1" ● 12.6 Analog inputs 18
"Digital input 1" ● 12.7 Digital inputs 19
"Digital input 2" ● 12.7 Digital inputs 19
"Digital input 3" ● 12.7 Digital inputs 19
"Predefined setpoint" ● 12.25 Predefined setpoints 18*
"External setpoint funct." ● 12.10 External setpoint function 21
"Signal relay 1" ● 12.8 Signal relays (Relay outputs) 20
"Signal relay 2" ● 12.8 Signal relays (Relay outputs) 20
"Alarm handling" ● 12.13 Alarm handling 24
"Service" ● 12.14 ""Number" (Pump number) 24
12.17 "Recall settings" (Recall stored
"Recall settings" ● 24
settings)
"Undo" ● 12.17.1 "Undo" 24
"Pump name" ● 12.18 "Pump name" 24
"Connection code" ● 12.19 "Connection code" 25
"Unit configuration" ● 12.16 "Unit configuration" (Units) 24

CMEC, CREC,
"Alarms and warnings" CRIEC, CRNEC, Section Page
MTREC

"Alarm log" ● 12.20 Alarm log 25

"Warning log" ● 12.21 Warning log 25
"Reset alarm" button ●

CMEC, CREC,
"Assist" CRIEC, CRNEC, Section Page
MTREC

"Assisted pump setup" ● 12.23 Assisted pump setup 25

"Assisted fault advice" ● 12.24 Assisted fault advice 25

Note:
"*": Page number refers to this document

14
 English (GB)
11. Grundfos GO
(For 2.2kW to 3kW models) 11.1 Communication
When Grundfos GO initiates communication with the
CAUTION
product, the indicator light in the centre of Grundfos
Radiation
Eye flashes green.
Minor or moderate personal injury
On products fitted with the HMI 100 or 200 operating
‐ Locate the product at a minimum
panel, you can enable communication by pressing the
distance of 20 cm from any body parts.
Communication button.
Human tissue may be heated by RF
energy. On products fitted with the HMI 300 operating panel,
the display indicates that a wireless device is trying to
Installers and end users must be provided connect to the product. Press OK on the operating
with these installation and operating panel to connect the product with Grundfos GO, or
instructions and operating conditions for press the Home button to reject connection.
satisfying RF exposure compliance.
1 2 3
The product is designed for wireless communication Symbol Description
with Grundfos GO using Bluetooth (BLE). Press OK on the operating panel
Grundfos GO enables you to set functions and gives to connect the product with
Status Settings
you access to status overviews, technical product Grundfos GO.
information and current operating parameters.
PressSetpoint
the Home button to reject Control mode
connection.
5.00 bar Const. pres
11.1.1 Bluetooth communica tion
Bluetooth communication can take place at distances
Operaring
up to 10 m. The first time Grundfosmode
GO Actual controlled
communicates with the product, you enable
communication by pressing theNormal
Communication
button or OK on the operating panel. 4.90 b
Later when communication takes place, the product is
recognised by Grundfos GO, and you can select the
product from the List menu.

9 8 7 6 5
TM082930

15
English (GB)

11.2 Menu overview for Grundfos GO (for 2.2kW to 3kW models)

CMEC, CREC,
Dashboard CRIEC, CRNEC,
MTREC

CMEC, CREC,
"Status" CRIEC, CRNEC,
MTREC
Pump and application
Actual controlled value ●
Resulting setpoint ●
Energy consumption ●
Power consumption ●
Motor speed ●
Operating Log
Operating hours ●
Inputs/outputs
Analog input 1 ●
Digital input 1 ●
Digital input 2 ●

Digital input/output 3 ●
Fitted modules
CIM module ●
Operating panel ●

16
 CMEC, CREC,
"Settings" CRIEC, CRNEC, Section Page
MTREC

English (GB)
"Setpoint" ● 12.1 Setpoint 17
"Operating mode" ● 12.2 Operating mode 17
"Set user-defined speed" ● 12.4 "Set user-defined speed" 17
"Control mode" ● 12.5 "Control mode" 17
12.11 "Stop function" (Low-flow stop
"Stop function" ● 22
function)
"Controller" ● "Controller" (Controller settings) 20
"Operating range" ● 12.9 Operating range 21
"Ramps" ● 12.12 Ramps 24
"Number" ● 12.14 ""Number" (Pump number) 24
12.15 "Radio communication"
"Radio communication" ● 24
(Enable/disable radio comm.)
"Analog input 1" ● 12.6 Analog inputs 18
"Digital input 1" ● 12.7 Digital inputs 19
"Digital input 2" ● 12.7 Digital inputs 19
"Digital input 3" ● 12.7 Digital inputs 19
"Predefined setpoint" ● 12.25 Predefined setpoints 18*
"External setpoint funct." ● 12.10 External setpoint function 21
"Signal relay 1" ● 12.8 Signal relays (Relay outputs) 20
"Signal relay 2" ● 12.8 Signal relays (Relay outputs) 20
"Alarm handling" ● 12.13 Alarm handling 24
"Service" ● 12.14 ""Number" (Pump number) 24
12.17 "Recall settings" (Recall stored
"Recall settings" ● 24
settings)
"Undo" ● 12.17.1 "Undo" 24
"Pump name" ● 12.18 "Pump name" 24
"Connection code" ● 12.19 "Connection code" 25
"Unit configuration" ● 12.16 "Unit configuration" (Units) 24

CMEC, CREC,
"Alarms and warnings" CRIEC, CRNEC, Section Page
MTREC

"Alarm log" ● 12.20 Alarm log 25

"Warning log" ● 12.21 Warning log 25
"Reset alarm" button ●

CMEC, CREC,
"Assist" CRIEC, CRNEC, Section Page
MTREC

"Assisted pump setup" ● 12.23 Assisted pump setup 25

"Assisted fault advice" ● 12.24 Assisted fault advice 25

Note:
"*": Page number refers to this document

17
 12.25 Predefined setpoints
English (GB)

You can set and activate three predefined setpoints

by combining the input signals to digital inputs 2, 3
as shown in the table below.
Set the digital inputs 2, 3 to "Predefined setpoints"
if all three predefined setpoints are to be used. You
can also set one or two of the digital inputs to
"Predefined setpoints" but this will limit the number
of predefined setpoints available.

Digital inputs
Setpoint
2 3

0 0 Normal setpoint or stop

1 0 Predefined setpoint 1
0 1 Predefined setpoint 2
1 1 Predefined setpoint 3

0 = Open contact
1 = Closed contact

Example
Figure below shows how you can use the digital
inputs to set up seven predefined setpoints. Digital
input 2 is open and digital inputs 3 is closed. If you
compare with the table above, you can see that
"Predefined setpoint 2" is activated.

Digital input 3
Digital input 2
Actual setpoint
3 Setpoint 3
2 Setpoint 2
1 Setpoint 1
0

Normal
Stop setpoint

Principle sketch showing how predefined setpoints

function

If all digital inputs are open, the pump will either

stop or run at the normal setpoint. Set the desired
action with Grundfos GO or with the advanced
control panel.

18
19
 Argentina China Hong Kong
Grundfos companies

Bombas GRUNDFOS de Argentina S.A. GRUNDFOS Pumps (Shanghai) Co. Ltd. GRUNDFOS Pumps (Hong Kong) Ltd.
Ruta Panamericana km. 37.500 Centro 10F The Hub, No. 33 Suhong Road Unit 1, Ground floor
Industrial Garin Minhang District Siu Wai Industrial Centre
1619 Garín Pcia. de B.A. Shanghai 201106 29-33 Wing Hong Street &
Phone: +54-3327 414 444 PRC 68 King Lam Street, Cheung Sha Wan
Telefax: +54-3327 45 3190 Phone: +86 21 612 252 22 Kowloon
Telefax: +86 21 612 253 33 Phone: +852-27861706 / 27861741
Australia Telefax: +852-27858664
GRUNDFOS Pumps Pty. Ltd. COLOMBIA
P.O. Box 2040 GRUNDFOS Colombia S.A.S. Hungary
Regency Park Km 1.5 vía Siberia-Cota Conj. Potrero GRUNDFOS Hungária Kft.
South Australia 5942 Chico, Tópark u. 8
Phone: +61-8-8461-4611 Parque Empresarial Arcos de Cota Bod. H-2045 Törökbálint,
Telefax: +61-8-8340 0155 1A. Phone: +36-23 511 110
Cota, Cundinamarca Telefax: +36-23 511 111
Austria Phone: +57(1)-2913444
GRUNDFOS Pumpen Vertrieb Telefax: +57(1)-8764586 India
Ges.m.b.H. GRUNDFOS Pumps India Private
Grundfosstraße 2 Croatia Limited
A-5082 Grödig/Salzburg GRUNDFOS CROATIA d.o.o. 118 Old Mahabalipuram Road
Tel.: +43-6246-883-0 Buzinski prilaz 38, Buzin Thoraipakkam
Telefax: +43-6246-883-30 HR-10010 Zagreb Chennai 600 096
Phone: +385 1 6595 400 Phone: +91-44 2496 6800
Belgium Telefax: +385 1 6595 499
N.V. GRUNDFOS Bellux S.A. www.hr.grundfos.com Indonesia
Boomsesteenweg 81-83 PT. GRUNDFOS POMPA
B-2630 Aartselaar GRUNDFOS Sales Czechia and Graha Intirub Lt. 2 & 3
Tél.: +32-3-870 7300 Slovakia s.r.o. Jln. Cililitan Besar No.454. Makasar,
Télécopie: +32-3-870 7301 Čajkovského 21 Jakarta Timur
779 00 Olomouc ID-Jakarta 13650
Belarus Phone: +420-585-716 111 Phone: +62 21-469-51900
Представительство ГРУНДФОС в Telefax: +62 21-460 6910 / 460 6901
Минске Denmark
220125, Минск GRUNDFOS DK A/S Ireland
ул. Шафарнянская, 11, оф. 56, БЦ Martin Bachs Vej 3 GRUNDFOS (Ireland) Ltd.
«Порт» DK-8850 Bjerringbro Unit A, Merrywell Business Park
Тел.: +375 17 397 397 3 Tlf.: +45-87 50 50 50 Ballymount Road Lower
+375 17 397 397 4 Telefax: +45-87 50 51 51 Dublin 12
Факс: +375 17 397 397 1 E-mail: [email protected] Phone: +353-1-4089 800
E-mail: [email protected] www.grundfos.com/DK Telefax: +353-1-4089 830
Bosnia and Herzegovina Estonia Italy
GRUNDFOS Sarajevo GRUNDFOS Pumps Eesti OÜ GRUNDFOS Pompe Italia S.r.l.
Zmaja od Bosne 7-7A, Peterburi tee 92G Via Gran Sasso 4
BH-71000 Sarajevo 11415 Tallinn I-20060 Truccazzano (Milano)
Phone: +387 33 592 480 Tel: + 372 606 1690 Tel.: +39-02-95838112
Telefax: +387 33 590 465 Fax: + 372 606 1691 Telefax: +39-02-95309290 / 95838461
www.ba.grundfos.com
e-mail: [email protected] Finland Japan
OY GRUNDFOS Pumput AB GRUNDFOS Pumps K.K.
Brazil Trukkikuja 1 1-2-3, Shin-Miyakoda, Kita-ku,
BOMBAS GRUNDFOS DO BRASIL FI-01360 Vantaa Hamamatsu
Av. Humberto de Alencar Castelo Phone: +358-(0) 207 889 500 431-2103 Japan
Branco, 630 Phone: +81 53 428 4760
CEP 09850 - 300 France Telefax: +81 53 428 5005
São Bernardo do Campo - SP Pompes GRUNDFOS Distribution S.A.
Phone: +55-11 4393 5533 Parc d’Activités de Chesnes Korea
Telefax: +55-11 4343 5015 57, rue de Malacombe GRUNDFOS Pumps Korea Ltd.
F-38290 St. Quentin Fallavier (Lyon) 6th Floor, Aju Building 679-5
Bulgaria Tél.: +33-4 74 82 15 15 Yeoksam-dong, Kangnam-ku, 135-916
Grundfos Bulgaria EOOD Télécopie: +33-4 74 94 10 51 Seoul, Korea
Slatina District Phone: +82-2-5317 600
Iztochna Tangenta street no. 100 Germany Telefax: +82-2-5633 725
BG - 1592 Sofia GRUNDFOS GMBH
Tel. +359 2 49 22 200 Schlüterstr. 33 Latvia
Fax. +359 2 49 22 201 40699 Erkrath SIA GRUNDFOS Pumps Latvia
email: [email protected] Tel.: +49-(0) 211 929 69-0 Deglava biznesa centrs
Telefax: +49-(0) 211 929 69-3799 Augusta Deglava ielā 60, LV-1035, Rīga,
Canada e-mail: [email protected] Tālr.: + 371 714 9640, 7 149 641
GRUNDFOS Canada Inc. Service in Deutschland: Fakss: + 371 914 9646
2941 Brighton Road e-mail: [email protected]
Oakville, Ontario Lithuania
L6H 6C9 Greece GRUNDFOS Pumps UAB
Phone: +1-905 829 9533 GRUNDFOS Hellas A.E.B.E. Smolensko g. 6
Telefax: +1-905 829 9512 20th km. Athinon-Markopoulou Av. LT-03201 Vilnius
P.O. Box 71 Tel: + 370 52 395 430
GR-19002 Peania Fax: + 370 52 395 431
Phone: +0030-210-66 83 400
Telefax: +0030-210-66 46 273
Malaysia Serbia Turkey

Grundfos companies
GRUNDFOS Pumps Sdn. Bhd. Grundfos Srbija d.o.o. GRUNDFOS POMPA San. ve Tic. Ltd.
7 Jalan Peguam U1/25 Omladinskih brigada 90b Sti.
Glenmarie Industrial Park 11070 Novi Beograd Gebze Organize Sanayi Bölgesi
40150 Shah Alam Phone: +381 11 2258 740 Ihsan dede Caddesi,
Selangor Telefax: +381 11 2281 769 2. yol 200. Sokak No. 204
Phone: +60-3-5569 2922 www.rs.grundfos.com 41490 Gebze/ Kocaeli
Telefax: +60-3-5569 2866 Phone: +90 - 262-679 7979
Singapore Telefax: +90 - 262-679 7905
Mexico GRUNDFOS (Singapore) Pte. Ltd. E-mail: [email protected]
Bombas GRUNDFOS de México S.A. de 25 Jalan Tukang
C.V. Singapore 619264 Ukraine
Boulevard TLC No. 15 Phone: +65-6681 9688 Бізнес Центр Європа
Parque Industrial Stiva Aeropuerto Telefax: +65-6681 9689 Столичне шосе, 103
Apodaca, N.L. 66600 м. Київ, 03131, Україна
Phone: +52-81-8144 4000 Slovakia Телефон: (+38 044) 237 04 00
Telefax: +52-81-8144 4010 GRUNDFOS s.r.o. Факс.: (+38 044) 237 04 01
Prievozská 4D E-mail: [email protected]
Netherlands 821 09 BRATISLAVA
GRUNDFOS Netherlands Phona: +421 2 5020 1426 United Arab Emirates
Veluwezoom 35 sk.grundfos.com GRUNDFOS Gulf Distribution
1326 AE Almere P.O. Box 16768
Postbus 22015 Slovenia Jebel Ali Free Zone
1302 CA ALMERE GRUNDFOS LJUBLJANA, d.o.o. Dubai
Tel.: +31-88-478 6336 Leskoškova 9e, 1122 Ljubljana Phone: +971 4 8815 166
Telefax: +31-88-478 6332 Phone: +386 (0) 1 568 06 10 Telefax: +971 4 8815 136
E-mail: [email protected] Telefax: +386 (0)1 568 06 19
E-mail: [email protected] United Kingdom
New Zealand GRUNDFOS Pumps Ltd.
GRUNDFOS Pumps NZ Ltd.
South Africa Grovebury Road
17 Beatrice Tinsley Crescent Grundfos (PTY) Ltd. Leighton Buzzard/Beds. LU7 4TL
North Harbour Industrial Estate 16 Lascelles Drive, Meadowbrook Estate Phone: +44-1525-850000
Albany, Auckland 1609 Germiston, Johannesburg Telefax: +44-1525-850011
Phone: +64-9-415 3240 Tel.: (+27) 10 248 6000
Telefax: +64-9-415 3250 Fax: (+27) 10 248 6002 U.S.A.
E-mail: [email protected] GRUNDFOS Pumps Corporation
Norway 9300 Loiret Blvd.
GRUNDFOS Pumper A/S
Spain Lenexa, Kansas 66219
Strømsveien 344 Bombas GRUNDFOS España S.A. Phone: +1-913-227-3400
Postboks 235, Leirdal Camino de la Fuentecilla, s/n Telefax: +1-913-227-3500
N-1011 Oslo E-28110 Algete (Madrid)
Tlf.: +47-22 90 47 00 Tel.: +34-91-848 8800 Uzbekistan
Telefax: +47-22 32 21 50 Telefax: +34-91-628 0465 Grundfos Tashkent, Uzbekistan The Rep-
resentative Office of Grundfos Kazakhstan
Poland Sweden in Uzbekistan
GRUNDFOS Pompy Sp. z o.o. GRUNDFOS AB 38a, Oybek street, Tashkent
ul. Klonowa 23 Box 333 (Lunnagårdsgatan 6) Телефон: (+998) 71 150 3290 / 71 150
Baranowo k. Poznania 431 24 Mölndal 3291
PL-62-081 Przeźmierowo Tel.: +46 31 332 23 000 Факс: (+998) 71 150 3292
Tel: (+48-61) 650 13 00 Telefax: +46 31 331 94 60
Fax: (+48-61) 650 13 50 Switzerland Addresses Revised 09.09.2020
Portugal GRUNDFOS Pumpen AG
Bombas GRUNDFOS Portugal, S.A. Bruggacherstrasse 10
Rua Calvet de Magalhães, 241 CH-8117 Fällanden/ZH
Apartado 1079 Tel.: +41-44-806 8111
P-2770-153 Paço de Arcos Telefax: +41-44-806 8115
Tel.: +351-21-440 76 00 Taiwan
Telefax: +351-21-440 76 90 GRUNDFOS Pumps (Taiwan) Ltd.
Romania 7 Floor, 219 Min-Chuan Road
Grundfos Pompe România SRL Taichung, Taiwan, R.O.C.
S-PARK BUSINESS CENTER, Clădirea Phone: +886-4-2305 0868
A2, Telefax: +886-4-2305 0878
etaj 2, Str. Tipografilor, Nr. 11-15, Sector Thailand
1, GRUNDFOS (Thailand) Ltd.
Cod 013714, Bucuresti, Romania, 92 Chaloem Phrakiat Rama 9 Road,
Tel: 004 021 2004 100 Dokmai, Pravej, Bangkok 10250
E-mail: [email protected] Phone: +66-2-725 8999
www.grundfos.ro Telefax: +66-2-725 8998
Russia
ООО Грундфос Россия
ул. Школьная, 39-41
Москва, RU-109544, Russia
Тел. (+7) 495 564-88-00 (495) 737-30-
00
Факс (+7) 495 564 8811
E-mail [email protected]
 ECM: 1409157
93173803 05.2024

www.grundfos.com
Trademarks displayed in this material, including but not limited to Grundfos, the Grundfos logo and “be
think innovate” are registered trademarks owned by The Grundfos Group. All rights reserved. © 2024 Grundfos Holding A/S, all rights reserved.