SFP+ Series
EOLP-1396-10-M series
1310nm SFP+ single-Mode Transceiver, With Digital Diagnostic Monitoring
1G 1000BASE-LX/10G BASE-LW/LR
Duplex SFP+ Transceiver, RoHS 6 Compliant
Features
Data rate selectable for 1.25G or 9.95~10.3G
1310nm DFB-LD Transmitter
Distance up to 10km
Single 3.3V Power supply and TTL Logic Interface
Duplex LC Connector Interface
Hot Pluggable
Power Dissipation < 1.0W
Applications
Compliant with MSA SFP+ Specification SFF-8431
10GBASE-LR at 10.31Gbps
Compliant with IEEE 802.3ae 10GBASE-LR/LW
10GBASE-LW at 9.95Gbps
Compliant with IEEE 802.3
1000BASE-LX 1G Ethernet
Operating Case Temperature
Other optical links
Standard: 0℃~+70℃
Industrial: -40℃~+85℃
Ordering information
Part No. Data Rate Laser Fiber Distance Interface Temp. DDMI
9.95Gbps
1310nm
EOLP-1396-10-M*note1 to 10.3Gbps SMF 10km LC Standard YES
DFB
1.25Gbps
9.95Gbps
1310nm
EOLP-1396-10-MI to 10.3Gbps SMF 10km LC Industrial YES
DFB
1.25Gbps
Note1: Standard version.
*The product image only for reference purpose.
Eoptolink Technology Inc., Ltd. V1.d
Page 1 of 9
SFP+ Series
Regulatory Compliance*Note2
Product Certificate Certificate Number Applicable Standard
EN 60950-1:2006+A11+A1+A12+A2
TUV R50135086 EN 60825-1:2014
EN 60825-2:2004+A1+A2
UL 60950-1
UL E317337
CSA C22.2 No. 60950-1-07
EN 55022:2010
EMC CE AE 50285865 0001
EN 55024:2010
FCC WTF14F0514417E 47 CFR PART 15 OCT., 2013
FDA / CDRH 1040.10
ROHS / 2011/65/EU
Note2: The above certificate number updated to June 2014, because some certificate will be updated every year,
such as FDA and ROHS. For the latest certification information, please check with Eoptolink.
Product Description
The EOLP-1396-10-M series single mode transceiver is small form factor pluggable module for
serial optical data communications such as IEEE 802.3ae 10GBASE-LR/LW and 1000BASE-LX
1G Ethernet. It is with the SFP+ 20-pin connector to allow hot plug capability.This module is
designed for single mode fiber and operates at a nominal wavelength of 1310 nm. The transmitter
section uses a 1310nm multiple quantum well DFB laser and is a class 1 laser according to
International Safety Standard IEC-60825.
The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical
header and a limiting post-amplifier IC.
Absolute Maximum Ratings
Parameter Symbol Min. Max. Unit
Storage Temperature TS -40 +85 °C
Supply Voltage VCC -0.5 3.6 V
Input Voltage Vin -0.5 Vcc V
Output Current Io - 50 mA
Recommended Operating Conditions
Parameter Symbol Min. Typical Max. Unit
Operating Case EOLP-1396-10-M 0 +70
Tc °C
Temperature EOLP-1396-10-MI -40 +85
Power Supply Voltage VCC 3.135 3.3 3.465 V
Power Supply Current ICC 300 mA
Surge Current ISurge +30 mA
10GBASE-LR 10.3
Baud Rate Gbps
10GBASE-LW 9.95
Eoptolink Technology Inc., Ltd. V1.d
Page 2 of 9
SFP+ Series
1000BASE-LX 1.25
Performance Specifications – Electrical
Parameter Symbol Min. Typ. Max Unit Notes
Transmitter
CML AC coupled
Vin 150 1200 mVpp
Inputs(Differential) inputs
Input AC Common
0 25 mV RMS
Mode Voltage
Input Impedance Rin > 100 kohms
Zin 85 100 115 ohm
(Differential) @ DC
Differential Input - - -12 0.01~1GHZ
SDD11 dB
S-parameter Note3 1~11.1GHZ
Differential to
Common Mode SCD11 - - -10 dB
Conversion
Tx_DISABLE Input
2 Vcc+0.3 V
Voltage – High
Tx_DISABLE Input
0 0.8 V
Voltage – Low
Tx_FAULT Output Io = 400µA; Host
2 Vcc+0.3 V
Voltage – High Vcc
Tx_FAULT Output
0 0.8 V Io = -4.0mA
Voltage – Low
Receiver
CML Outputs AC coupled
Vout 350 700 mVpp
(Differential) outputs
Output AC Common
0 15 mV RMS
Mode Voltage
Output Impedance
Zout 85 100 115 ohm
(Differential)
Differential Output - - -12 0.01~1GHZ
SD22 dB
S-parameter Note4 1~11.1GHZ
Rx_LOS Output lo = 400µA; Host
2 Vcc+0.3 V
Voltage – High Vcc
Rx_LOS Output
0 0.8 V lo = -4.0mA
Voltage – Low
VoH 2.5 V
MOD_DEF ( 0:2 ) With Serial ID
VoL 0 0.5 V
Note3 :Reflection Coefficient given by equation SDD11(dB)=Max(-12 + 2*SQRT(f) -6.3+13Log10(f/5.5)), with f in
GHz.
Note4: Differential Output S-parameter given by equation SDD22(dB)= Max(-12 + 2*SQRT(f) -6.3+13Log10(f/5.5)),
with f in GHz.
Eoptolink Technology Inc., Ltd. V1.d
Page 3 of 9
SFP+ Series
Performance Specifications – Optical
Parameter Symbol Min Typical Max. Unit
9µm Core Diameter SMF 10 km
10GBASE-LR 10.3
Data Rate Gbps
1000BASE-LX 1.25
Transmitter
Centre Wavelength λC 1270 1310 1355 nm
Spectral Width (-20dB) ∆λ 1 nm
Side Mode Suppression Ratio SMSR 30 dB
[email protected] -8.2 +0.5
Average Output Power dBm
[email protected] -9.5 -3
[email protected] 3.5
Extinction Ratio dB
[email protected] 9
Average Power of OFF Transmitter Poff -30 dBm
Transmitter Dispersion Penalty TDP 3.2 dB
Receiver
Centre Wavelength λ 1260 1565 nm
[email protected] -14.4
Sensitivity*note5 dBm
[email protected] -21
Receiver Overload Pmax 0.5 dBm
Optical Return Loss ORL -12 dB
[email protected] -16
LOS De-Assert dBm
[email protected] -22
[email protected] -28
LOS Assert dBm
[email protected] -35
Note5: Measured with a PRBS 231 -1 test pattern @ 10.3125Gbps, BER≤10-12, measured with a PRBS 27 -1 test
pattern @ 1.25Gbps, BER≤10-12.
SFP+ Transceiver Electrical Pad Layout
Eoptolink Technology Inc., Ltd. V1.d
Page 4 of 9
SFP+ Series
Pin Function Definitions
Pin Plug
Name FUNCTION Notes
Num. Seq.
1 VeeT Transmitter Ground 1 Note 5
Transmitter Fault
2 TX Fault 3 Note 1
Indication
TX Note 2, Module disables on high or
3 Transmitter Disable 3
Disable open
4 SDA Module Definition 2 3 Data line for Serial ID.
5 SCL Module Definition 1 3 Clock line for Serial ID.
6 MOD-ABS Module Definition 0 3 Note 3
RX Rate Select This pin has an internal 30k pull down
7 RS0 3
(LVTTL). to ground. See note 9 for details.
8 LOS Loss of Signal 3 Note 4
TX Rate Select
9 RS1 1 No connection
(LVTTL).
10 VeeR Receiver Ground 1 Note 5
11 VeeR Receiver Ground 1 Note 5
Inv. Received Data
12 RD- 3 Note 6
Out
13 RD+ Received Data Out 3 Note 7
14 VeeR Receiver Ground 1 Note 5
15 VccR Receiver Power 2 3.3V ± 5%, Note 7
16 VccT Transmitter Power 2 3.3V ± 5%, Note 7
17 VeeT Transmitter Ground 1 Note 5
18 TD+ Transmit Data In 3 Note 8
19 TD- Inv. Transmit Data In 3 Note 8
20 VeeT Transmitter Ground 1 Note 5
Eoptolink Technology Inc., Ltd. V1.d
Page 5 of 9
SFP+ Series
Notes:
1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor
on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a
laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled
to < 0.8V.
2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up
within the module with a 4.7K – 10 KΩ resistor. Its states are:
Low (0 – 0.8V): Transmitter on
(>0.8, < 2.0V): Undefined
High (2.0 – 3.465V): Transmitter Disabled
Open: Transmitter Disabled
3) Modulation Absent, connected to VeeT or VeeR in the module.
4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K –
10KΩ resistor. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates
the received optical power is below the worst-case receiver sensitivity (as defined by the standard
in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
5) VeeR and VeeT may be internally connected within the SFP+ module.
6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines
which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done
inside the module and is thus not required on the host board.
7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5%
at the SFP+ connector pin. Maximum supply current is 300mA. Inductors with DC resistance of less
than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V
supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+
transceiver module will result in an inrush current of no more than 30mA greater than the steady
state value. VccR and VccT may be internally connected within the SFP+ transceiver module.
8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with
100Ω differential termination inside the module. The AC coupling is done inside the module and is
thus not required on the host board.
9)This module provides two inputs RS0 and RS1 that can optionally be used for rate selection. RS0
controls the receive path signal rate capability, RS1 not used, as defined in Table1. This rate select
functionality can also be controlled by software as defined by SFF-8472.
Parameter State Conditions
Low RX data rate is selected as 1.25Gbps
RS0
High RX data rate is selected as 9.95~10.3Gbps
RS1 NC This pin is not used
Table 1 Rate Select Hardware Control Contacts
Eoptolink Technology Inc., Ltd. V1.d
Page 6 of 9
SFP+ Series
EEPROM
The serial interface uses the 2-wire serial CMOS EEPROM protocol defined for the ATMEL
AT24C02/04 family of components. When the serial protocol is activated, the host generates the
serial clock signal (SCL). The positive edge clocks data into those segments of the EEPROM that
are not written protected within the SFP+ transceiver. The negative edge clocks data from the
SFP+ transceiver. The serial data signal (SDA) is bi-directional for serial data transfer. The host
uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The
memories are organized as a series of 8-bit data words that can be addressed individually or
sequentially.
The Module provides diagnostic information about the present operating conditions. The
transceiver generates this diagnostic data by digitization of internal analog signals. Calibration and
alarm/warning threshold data is written during device manufacture. Received power monitoring,
transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature
monitoring all are implemented. If the module is defined as external calibrated, the diagnostic data
are raw A/D values and must be converted to real world units using calibration constants stored in
EEPROM locations 56 – 95 at wire serial bus address A2h. The digital diagnostic memory map
specific data field define as following .For detail EEPROM information, please refer to the related
document of SFF 8472 Rev 10.2.
Eoptolink Technology Inc., Ltd. V1.d
Page 7 of 9
SFP+ Series
Recommend Circuit Schematic
Mechanical Specifications
*This 2D drawing only for reference, please check with Eoptolink before ordering.
Eoptolink Technology Inc., Ltd. V1.d
Page 8 of 9
SFP+ Series
Eye Safety
This single-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21
CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and
voltage limits. The optical ports of the module shall be terminated with an optical connector or with
a dust plug.
Obtaining Document
You can visit our website:
http://www.eoptolink.com
Or contact Eoptolink Technology Inc., Ltd. Listed at the end of the documentation to get the latest
document.
Revision History
Revision Initiated Reviewed Approved Revision History Release Date
V1.a Angela Kelly Released. Dec 7,2012
Update the regulatory
Kelly/Torres compliance, the
/Fing/JP/ specifications of
V1.b Angela Alex Feb 24,2016
Eason/Jaso Vin,Vout,[email protected]
n/Martin bps,[email protected]
s and 2D drawing.
Kelly/Fing/ Update a slip of the
V1.c Angela April 27,2016
JP/Eason pen.
Kelly/ Update the picture, 2D
V1.d Angela William/ Phlio drawing and contact. March 22, 2018
Chao.Wang
Notice:
Eoptolink reserves the right to make changes to or discontinue any optical link product or service
identified in this publication, without notice, in order to improve design and/or performance.
Applications that are described herein for any of the optical link products are for illustrative
purposes only. Eoptolink makes no representation or warranty that such applications will be
suitable for the specified use without further testing or modification.
Contact:
Add: No.127 West Wulian Street, Gongxing Town, Shuangliu district, Chengdu City, Sichuan,
China.
Tel: (+86) 028-67087999
Fax: (+86) 28-67087979-8010
Postal: 610213
E-mail:[email protected]
http://www.eoptolink.com
Eoptolink Technology Inc., Ltd. V1.d
Page 9 of 9
