TVS Diodes

Surface Mount – 3000W > SMDJ series

SMDJ Series RoHS Pb e3

Description
Uni-directional
The SMDJ series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.

Features
• 3000 W PPPM capability • UL Recognized compound
at 10/1000μs waveform, meeting flammability rating
repetition rate (duty V-0
Bi-directional cycles):0.01% • Halogen free and
• For surface mounted RoHS compliant
applications in order to • Pb-free E3 means 2nd level
Agency Approvals optimize board space interconnect is Pb-free and
• Typical failure mode is short the terminal finish material is
Agency Agency File Number from over-specified voltage or tin(Sn) (IPC/JEDEC J-STD-
E230531 current 609A.01)
• Whisker test is conducted • Recognized to UL 497B
based on JEDEC JESD201A as an Isolated Loop Circuit
Maximum Ratings and Thermal Characteristics
per its table 4a and 4c pass Protector
(TA=25OC unless otherwise noted) class 1 and 2 ■ Products manufactured in
• Glass passivated chip junction the Philippines are available.
Parameter Symbol Value Unit
• IEC-61000-4-2 ESD 30kV(Air), -Parts with an E suffix are
Peak Pulse Power Dissipation(Fig.2) manufactured outside China.
30kV (Contact)
by 10/1000us Test Waveform(Fig.4) (Note PPPM 3000 W ( See Ordering and Packaging
1),(Note 2) -Single Die Parts • Low dynamic resistance
Options section for details)
Peak Pulse Power Dissipation(Fig.2) • VBR @ TJ= VBR@25°C x (1+αT
by 10/1000us Test Waveform(Fig.4) (Note PPPM 4000 W x (TJ - 25))(αT:Temperature
1), (Note 2) -Stacked Die Parts (Note 5) Coefficient, typical
Power Dissipation on Infinite Heat Sink value is 0.1%)
PD 6.5 W
at TL=50OC

Peak Forward Surge Current, 8.3ms

IFSM 300 A
Single Half Sine Wave (Note 3)
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional VF 3.5/5.0 V
Only(Note 4)
-65 to
Operating Temperature Range TJ °C
150
-65 to
Storage Temperature Range TSTG °C
175 Applications
Typical Thermal Resistance Junction to
RƟJL 15 °C/W
Lead TVS components are ideal for the protection of I/O
Typical Thermal Resistance Junction to Interfaces, VCC bus and other vulnerable circuits used in
RƟJA 75 °C/W
Ambient telecom, computer, Industrial and consumer electronic
Notes: applications.
1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3.
2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
component only, duty cycle=4 per minute maximum.
4. VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts.
5. For stacked die component details, please refer to part numbers labeled by * in Electrical
Characteristics.

Functional Diagram Additional Infomarion

Bi-directional
Datasheet Resources Samples

Cathode Anode

Uni-directional
© 2025 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2
 TVS Diodes
Surface Mount – 3000W > SMDJ series

Electrical Characteristics (T =25°C unless otherwise noted)

A

Maximum Maximum Maximum Maximum

Breakdown Maximum
Marking Test Clamping Peak Clamping Peak Maximum Agency
Part Part Reverse Voltage V Reverse
Current Voltage VC Pulse Voltage VC Pulse Temperature Approval
Number Number Stand off Leakage IR
IT @ Current @ Current coefficient
(Uni) (Bi) Voltage V @ VR
UNI BI MIN MAX (mA) Ipp(10/1000μs) Ipp(10/1000μs) Ipp(8/20μs) Ipp(8/20μs) of VBR (%/C)
(μA)
(V) (A) (V) (A)
SMDJ5.0A SMDJ5.0CA RDE DDE 5.0 6.40 7.00 10 9.2 326.1 11.89 1630.5 800 0.041 X
SMDJ6.0A SMDJ6.0CA RDG DDG 6.0 6.67 7.37 10 10.3 291.3 13.31 1456.5 800 0.046 X
SMDJ6.5A SMDJ6.5CA RDK DDK 6.5 7.22 7.98 10 11.2 267.9 14.47 1339.5 500 0.052 X
SMDJ7.0A SMDJ7.0CA PDM DDM 7.0 7.78 8.60 10 12.0 250.0 15.50 1250.0 200 0.058 X
SMDJ7.5A SMDJ7.5CA PDP DDP 7.5 8.33 9.21 1 12.9 232.6 16.67 1163.0 100 0.061 X
SMDJ8.0A SMDJ8.0CA PDR DDR 8.0 8.89 9.83 1 13.6 220.6 17.57 1103.0 50 0.064 X
SMDJ8.5A SMDJ8.5CA PDT DDT 8.5 9.44 10.40 1 14.4 208.3 18.60 1041.5 20 0.066 X
SMDJ9.0A SMDJ9.0CA PDV DDV 9.0 10.00 11.10 1 15.4 194.8 19.90 974.0 10 0.069 X
SMDJ10A SMDJ10CA PDX DDX 10.0 11.10 12.30 1 17.0 176.5 21.96 882.5 5 0.071 X
SMDJ11A SMDJ11CA PDZ DDZ 11.0 12.20 13.50 1 18.2 164.8 23.51 824.0 2 0.074 X
SMDJ12A SMDJ12CA PEE DEE 12.0 13.30 14.70 1 19.9 150.8 25.71 754.0 2 0.075 X
SMDJ13A SMDJ13CA PEG DEG 13.0 14.40 15.90 1 21.5 139.5 27.78 697.5 2 0.076 X
SMDJ14A SMDJ14CA PEK DEK 14.0 15.60 17.20 1 23.2 129.3 29.97 646.5 2 0.08 X
SMDJ15A SMDJ15CA PEM DEM 15.0 16.70 18.50 1 24.4 123.0 31.52 615.0 2 0.083 X
SMDJ16A SMDJ16CA PEP DEP 16.0 17.80 19.70 1 26.0 115.4 33.59 577.0 2 0.084 X
SMDJ17A SMDJ17CA PER DER 17.0 18.90 20.90 1 27.6 108.7 35.66 543.5 2 0.085 X
SMDJ18A SMDJ18CA PET DET 18.0 20.00 22.10 1 29.2 102.7 37.73 513.5 2 0.088 X
SMDJ20A SMDJ20CA PEV DEV 20.0 22.20 24.50 1 32.4 92.6 41.86 463.0 2 0.091 X
SMDJ22A SMDJ22CA PEX DEX 22.0 24.40 26.90 1 35.5 84.5 45.87 422.5 2 0.092 X
SMDJ24A SMDJ24CA PEZ DEZ 24.0 26.70 29.50 1 38.9 77.1 50.26 385.5 2 0.092 X
SMDJ26A SMDJ26CA PFE DFE 26.0 28.90 31.90 1 42.1 71.3 54.39 356.5 2 0.093 X
SMDJ28A SMDJ28CA PFG DFG 28.0 31.10 34.40 1 45.4 66.1 58.66 330.5 2 0.094 X
SMDJ30A SMDJ30CA PFK DFK 30.0 33.30 36.80 1 48.4 62.0 62.53 310.0 2 0.096 X
SMDJ33A SMDJ33CA PFM DFM 33.0 36.70 40.60 1 53.3 56.3 68.86 281.5 2 0.097 X
SMDJ36A SMDJ36CA PFP DFP 36.0 40.00 44.20 1 58.1 51.6 75.06 258.0 2 0.098 X
SMDJ40A SMDJ40CA PFR DFR 40.0 44.40 49.10 1 64.5 46.5 83.33 232.5 2 0.099 X
SMDJ43A SMDJ43CA PFT DFT 43.0 47.80 52.80 1 69.4 43.2 89.66 216.0 2 0.1 X
SMDJ45A SMDJ45CA PFV DFV 45.0 50.00 55.30 1 72.7 41.3 93.93 206.5 2 0.101 X
SMDJ48A SMDJ48CA PFX DFX 48.0 53.30 58.90 1 77.4 38.8 100.00 194.0 2 0.101 X
SMDJ51A SMDJ51CA PFZ DFZ 51.0 56.70 62.70 1 82.4 36.4 106.46 182.0 2 0.101 X
SMDJ54A SMDJ54CA RGE DGE 54.0 60.00 66.30 1 87.1 34.4 112.53 172.0 2 0.102 X
SMDJ58A SMDJ58CA PGG DGG 58.0 64.40 71.20 1 93.6 32.1 120.93 160.5 2 0.103 X
SMDJ60A SMDJ60CA PGK DGK 60.0 66.70 73.70 1 96.8 31.0 125.06 155.0 2 0.103 X
SMDJ64A SMDJ64CA PGM DGM 64.0 71.10 78.60 1 103.0 29.1 133.07 145.5 2 0.104 X
SMDJ70A SMDJ70CA PGP DGP 70.0 77.80 86.00 1 113.0 26.5 145.99 132.5 2 0.105 X
SMDJ75A SMDJ75CA PGR DGR 75.0 83.30 92.10 1 121.0 24.8 156.33 124.0 2 0.106 X
SMDJ78A SMDJ78CA PGT DGT 78.0 86.70 95.80 1 126.0 23.8 162.79 119.0 2 0.106 X
SMDJ85A SMDJ85CA PGV DGV 85.0 94.40 104.00 1 137.0 21.9 177.00 109.5 2 0.106 X
SMDJ90A SMDJ90CA PGX DGX 90.0 100.00 111.00 1 146.0 20.5 188.63 102.5 2 0.107 X
SMDJ100A SMDJ100CA PGZ DGZ 100.0 111.00 123.00 1 162.0 18.5 209.30 92.5 2 0.107 X
SMDJ110A SMDJ110CA PHE DHE 110.0 122.00 135.00 1 177.0 16.9 228.68 84.5 2 0.107 X
SMDJ120A SMDJ120CA PHG DHG 120.0 133.00 147.00 1 193.0 15.5 249.35 77.5 2 0.108 X
SMDJ130A SMDJ130CA PHK DHK 130.0 144.00 159.00 1 209.0 14.4 270.03 72.0 2 0.108 X
SMDJ150A - PHM - 150.0 167.00 185.00 1 243.0 12.3 313.95 61.5 2 0.108 X
- SMDJ150CA* - DHM 150.0 167.00 185.00 1 243.0 16.5 313.95 61.5 2 0.108 X
SMDJ160A - PHP - 160.0 178.00 197.00 1 259.0 11.6 334.63 58.0 2 0.108 X
- SMDJ160CA* - DHP 160.0 178.00 197.00 1 259.0 15.5 334.63 58.0 2 0.108 X
SMDJ170A - PHR - 170.0 189.00 209.00 1 275.0 10.9 355.30 54.5 2 0.108 X
- SMDJ170CA* - DHR 170.0 189.00 209.00 1 275.0 14.6 355.30 54.5 2 0.108 X
SMDJ180A* SMDJ180CA* PHT DHT 180.0 200.00 221.00 1 292.0 13.7 377.26 51.5 2 0.108 X
SMDJ200A* SMDJ200CA* PHV DHV 200.0 224.00 247.00 1 324.0 12.4 418.60 46.5 2 0.11 X
SMDJ220A* SMDJ220CA* PKE DKE 220.0 244.00 270.00 1 356.0 11.3 459.95 42.0 2 0.11 X
SMDJ250A* SMDJ250CA* PKG DKG 250.0 279.00 309.00 1 405.0 9.9 523.26 37.5 2 0.11 X
SMDJ300A* SMDJ300CA* PKI DKI 300.0 335.00 371.00 1 486.0 8.3 627.91 31.0 2 0.112 X
SMDJ350A* SMDJ350CA* PKJ DKJ 350.0 391.00 432.00 1 567.0 7.1 732.56 26.5 2 0.112 X
SMDJ400A* SMDJ400CA* PKL DKL 400.0 447.00 494.00 1 648.0 6.2 837.21 23.5 2 0.112 X
SMDJ440A* SMDJ440CA* PKN DKN 440.0 492.00 543.00 1 713.0 5.7 921.19 21.5 2 0.112 X

For bidirectional type having VR of 10 volts and less, the IR limit is double.
For stack-die parts, use * to label the part number.
For uni-directional 5 V to 170 V, bi-directional 5 V to 130 V, add “-E” to the part number for COO Ex-China Site.

© 2025 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2
 TVS Diodes
Surface Mount – 3000W > SMDJ series

I-V Curve Characteristics

Uni-directional Bi-directional

Ipp

IT
Vc VBR VR Vc VBR VR IR
V V
IR VF IR VR VBR Vc
IT IT

Ipp
Ipp

PPPM Peak Pulse Power Dissipation (IPP x Vc) -- Max power dissipation
VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
VBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional

Ratings and Characteristic Curves (T =25°C unless otherwise noted)

A

Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating

100
PPPM-Peak Pulse Power (kW)

Transients Voltage stacked-die, 4kW

at 10/1000µs, 25°C

10
Single die, 3kW
Voltage or Current

at 10/1000µs, 25°C

TJ initial = Tamb
0.1
0.001 0.01 0.1 1 10
Current Through TVS
td-Pulse Width (ms)
Time

continues on next page.

© 2025 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2
 TVS Diodes
Surface Mount – 3000W > SMDJ series

Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A

Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform

100
150
Peak Pulse Power (PPP) or Current (IPP)

tr=10µsec TJ=25°C

IPPM- Peak Pulse Current, % IRSM

Pulse Width(td) is defined
80 as the point where the peak
Derating in Percentage %

current decays to 50% of IPPM

Peak Value
100 IPPM
60
Half Value

40
IPPM IPPM ( )
2

50 10/1000µsec. Waveform
as defined by R.E.A

20
td
0
0 0 1.0 2.0 3.0 4.0
0 25 50 75 100 125 150 175
t-Time (ms)
TJ - Initial Junction Temperature (ºC)

Figure 6 - Maximum Non-Repetitive Peak Forward

Figure 5 - Typical Junction Capacitance
Surge Current Uni-Directional Only

100000 500

Uni-direconal V=0V 450

IFSM - Peak Forward Surve Current (A)

10000 Bi-direconal V=0V 400

350
1000
Uni-direconal V=VR
300
Cj(pF)

250
Bi-direconal V=VR
100 200

150
10 100

50
1 0
1 10 100 1000 1 10 100
VBR - Reverse Breakdown Voltage(V) Number of Cycles at 60 Hz

Figure 7 - Peak Forward Voltage Drop vs Peak Forward

Current (Typical Values)

100 Single die

IF- Peak Forward Current(A)

10
Stack-die

0.1

0.01
0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00
VF-Peak Forward Voltage(V)

© 2025 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2
 TVS Diodes
Surface Mount – 3000W > SMDJ series

Soldering Parameters

Reflow Condition Lead–free assembly

tp
TP
- Temperature Min (Ts(min)) 150°C Ramp-up Critical Zone
TL to TP
Pre Heat - Temperature Max (Ts(max)) 200°C TL tL

Temperature (T)
- Time (min to max) (ts) 60 – 120 secs Ts(max)

Average ramp up rate (Liquidus Temp (TL) to Ramp-down

3°C/second max Ts(min)
peak ts
Preheat
TS(max) to TL - Ramp-up Rate 3°C/second max

- Temperature (TL) (Liquidus) 217°C 25˚C

Reflow t 25˚C to Peak

- Time (min to max) (tL) 60 – 150 seconds Time (t)

Peak Temperature (TP) 260+0/-5 °C

Time within 5°C of actual peak Temperature

30 seconds Environmental Specifications
(tp)

Ramp-down Rate 6°C/second max 100 % DC reverse

High Temp Voltage
voltage rated 150 °C, 1008 hours JEDEC,
Time 25°C to peak Temperature (TP) 8 minutes Max. Blocking (HTRB)
JESD22-A-108
Do not exceed 260°C
Biased Temp & 80 % breakdown voltage (+85 °C) 85 %RH, 1008
Humidity (H3TRB) hours JEDEC, JESD22-A-101
Physical Specifications Unbiased Highly
Accelerated 96 hours at TA = 130 °C/85 %RH. JEDEC,
Weight 0.007 ounce, 0.21 grams Stress Test JESD22-A-118
(UHAST)
JEDEC DO214AB. Molded plastic body over glass
Case
passivated junction -55 °C to +150 °C, 15 min. dwell, 1000 cycles.
Temp Cycling (TC)
Color band denotes positive end (cathode) except for JEDEC, JESD22-A104
Polarity
bidirectional versions.
Terminal Matte Tin-plated leads, Solderable per JESD22-B102 Moisture Sensitivity 85 %RH, +85 °C, 168 hours, 3 reflow cycles
Level (MSL) (+260 °C Peak). JEDEC, JEDEC-J-STD-020, Level 1

Resistance to +260 °C, 30 seconds JEDEC, JEDEC

Solder Heat (RSH) JESD22-A-111

Dimensions
DO-214AB (SMC J-Bend)
Cathode Band Inches Millimeters
(for uni-directional products only) Dimensions
Min Max Min Max
A 0.114 0.126 2.900 3.200
A C B 0.260 0.280 6.600 7.110
C 0.220 0.245 5.590 6.220
D 0.079 0.103 2.060 2.620
B
E 0.030 0.060 0.760 1.520
F - 0.008 - 0.203
H
G 0.305 0.320 7.750 8.130
D
H 0.006 0.012 0.152 0.305
I 0.129 - 3.300 -
F
E G J 0.094 - 2.400 -
K - 0.165 4.200
Dimensions in J L
inches andK(millimeters) L 0.094 - 2.400 -

Solder Pads
(all dimensions in mm) © 2025 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2
 TVS Diodes
Surface Mount – 3000W > SMDJ series

Part Numbering System Part Marking System

SMDJ XXX C A
Manufacture Site/ COO Cathode Band
Blank : China + Ex-China (for uni-directional products only)

F
-T7 : China + Ex-China
-E : Ex-China Littelfuse Logo
5% VBR VOLTAGE TOLERANCE

BI-DIRECTIONAL

VR VOLTAGE
XXX
YMXXX
Marking Code

SERIES Trace Code Marking

Y:Year Code
M: Month Code
XXX: Lot Code

Ordering and Packaging Options

Component Packaging
Part number Quantity Packaging Manufacture Site/ COO
Package Option

SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm tape/13” reel EIA STD RS-481 China + Ex-China
SMDJxxxXX-T7 DO-214AB 500 Tape & Reel – 16mm tape/7” reel EIA STD RS-481 China + Ex-China
SMDJxxxXX-E (1)(2) DO-214AB 3000 Tape & Reel - 16mm tape/13” reel EIA STD RS-481 Ex-China
Footnote:
1. Uni-directional product voltage range from 5 V to 170 V
2. Bi-directional product voltage range from 5 V to 130 V

Tape and Reel Specification

0.157
(4.0) Cathode

0.63
(16.0)

0.315 0.059 DIA Cover tape

(8.0) (1.5)
Optional *For Uni-directional Products only
7” 7.0 (187)
13” 13.0 (330)
Dimensions are in inches
0.80 (20.2) (and millimeters).
Arbor Hole Dia.

Direction of Feed
0.65
(16.4)

Label

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each
product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.
Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics.
© 2025 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: JC.02/27/25 v.2