Technical Data Sheet
Lupranate® 5100 Isocyanate
Lupranate 5100 Isocyanate is an isocyanate blend of monomeric and polymeric MDI. Typical use is
for flexible slab stock and molded Visco-Elastic memory foams.
T TYPICAL PROPERTIES
Appearance ……………………………………………………………………………………….....……… amber liquid
NCO content, wt% …………………………………………………………………………………………………… 32.6
Viscosity @ 25°C, cps ……………………………………………………………………………………………….... 33
Hydrolyzable chlorine, ppm …………………………………………………………………………………..….. < 100
Flash point, °C (COC) ………………………………………………………………………………………….…... > 200
Density @25°C, g/cm3 ……………………………………………………………………………………………….. 1.22
Initial boiling point, 5mm Hg, °C …………………………………………………………………………………… 200
Vapor Pressure @25°C, mm Hg ………………………………………………………………………………. 0.00001
Storage
Lupranat 5100 Isocyanate is supplied in tank trucks, totes and drums. Once a container has been opened, care should be taken
to exclude moisture. The most favorable temperature for storage is 25-35°C. If stored at higher temperatures, or if moisture is
not excluded, an undesirable increase in viscosity will occur. Below 15°C, the product becomes difficult to pump and pour. Below
12°C, crystallization may occur. The shelf life of Lupranate 5100 Isocyanate is six months if the temperature is maintained at 25
to 35°C and moisture is excluded.
Warning
Excessive heating or prolonged heating at 80-100°C may cause dangerous pressure build-up. Heating by electrical means is not
recommended due to the danger of local overheating, which would result in dimer formation. Melting in a water bath is not recommended
because of the potential danger of the isocyanate reacting with water in case of drum leakage. Rolling the drum in atmospheric steam is an
alternate procedure that can be used provided care is taken to ensure that the drum does not leak.
In case of chemical emergency:
Call CHEMTREC 800-424-9300 or BASF (800-832-HELP) day or night for assistance and information
concerning spilled material, fire, exposure and other chemical accidents. Outside the U.S., call (703) 527-3887.
Attention:
This product is sold solely for use by industrial institutions. Refer to our Safety Data Sheet (SDS) regarding regulatory compliance, safety,
hazards, spill procedures and disposal of this product. An SDS as well as additional information on BASF urethane chemicals may be obtained
by telephoning BASF Corporation, Urethane Customer Service at (877) 297-3322 or faxing (734) 324-6866.
Important:
While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, it is provided
for your guidance only. Because many factors may affect processing or application/use, we recommend that you make tests to determine the
suitability of a product for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING
Month 2019 rev Page 1 of 2
PRODUCTS DESCRIBED OR DESIGNS, DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS, DESIGNS, DATA OR
INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL
THE DESCRIPTIONS, INFORMATION, DATA OR DESIGNS PROVIDED BE CONSIDERED A PART OF OUR TERMS AND
CONDITIONS OF SALE.
Further, you expressly understand and agree that the descriptions, designs, data, and information furnished by
BASF hereunder are provided gratis and BASF assumes no obligation or liability for the description, designs,
data and information given or results obtained, all such being given and accepted at your risk.
© BASF Corporation, 2018
BASF Corporation is fully committed to the Responsible Care® initiative in
the USA, Canada, and Mexico.
For more information on Responsible Care® go to:
U.S.: www.basf.us/responsiblecare_usa
Canada: www.basf.us/responsiblecare_canada
México: www.basf.us/responsiblecare_mexico
BASF Corporation
1609 Biddle Avenue
Wyandotte, MI 48192
Phone: (734) 324-6100
https://polyurethanes.basf.us/
Month 2019 rev Page 2 of 2
