SPECIFICATIONS

D03 Pattern
Directional Control Valves

Also refer to "Directional Valve Features, Selection and Operating

Recommendations" (dynexdcvoperating.pdf)

CONTACT INFORMATION
USA Headquarters
Dynex/Rivett Inc.
770 Capitol Drive
Pewaukee, WI 53072 U.S.A.
Tel: 262-691-2222
FAX: 262-691-0312
E-mail: [email protected]

Power Units & Systems

Dynex/Rivett Inc.
54 Nickerson Road
Ashland, MA 01721 U.S.A.
Tel: 508-881-5110
FAX: 508-881-6849
E-mail: [email protected]

European Sales
Dynex/Rivett Inc.
Unit C5 Steel Close, Little End Road, Eaton Socon,
Huntingdon, Cambs. PE19 8TT United Kingdom
Tel: +44 (0) 1480 213980
FAX: +44 (0) 1480 405662
E-mail: [email protected]

For more information

visit our web site:
www.dynexhydraulics.com

BROCHURE NOTES:
Consult the Dynex sales department for a review of any application which requires operating above
the rated flows or pressures, or higher than normal operating temperatures.
Specifications shown were in effect when published. Since errors or omissions are possible, contact
your sales representative for the most current specifications before ordering. Dynex reserves the right
to discontinue or change designs at any time without incurring any obligation.

DYNEX High Pressure Hydraulics

Copyright © Dynex/Rivett Inc. Bulletin dynexvesd03specs-1101

 D03 PATTERN

Compact Valves
Control Flow to
15 U.S. gpm (57 L/min)
High performance D03 valves are
rated for 8 U.S. gpm (30 L/min)
nominal and 15 U.S. gpm (57 L/min)
maximum flow, at pressures to
5000 psi (350 bar).
This high pressure and high flow
capability provides great efficiency in
a very compact size.
6500 Series
HIGH EFFICIENCY OPERATION Explosion Proof 6500 Series
Double Solenoid
Large internal flow passages, with
uniform flow areas throughout the
body coring, provide exceptional
efficiency. Typical loop pressure drop
(open center spool) is a low 98 psi at
8 U.S. gpm (7 bar at 30 L/min) nominal 6800 Series 6900 Series
flow (∆P loop = P→A + B →T). Hydraulic Piloted Air Piloted

SMOOTH, RELIABLE SHIFTING

A four-land spool design assures
exceptionally smooth spool travel.
Additional outboard lands provide
greater support, eliminating spool
imbalance. RELIABLE VALVE SEALING
HIGH PRESSURE TANK PORT
Balancing grooves provide precise Tapered o-ring counterbores reduce
centering, reducing silt buildup and High pressure tank port capability
provides the highest “T” port rating leakage, by assuring seal retention
potential spool sticking. in high flow or rapid cycling
available. This option (“HPT”) is ideal
for higher pressure “series” circuits. operation. High-torque mounting
prevents weepage between sections
when using sandwich accessory
valves.

2000 3000
DC
PRESSURE VALVE
AC PORT BODY
1000 4000

0 5000 MOUNTING SURFACE

Close tolerances assure accurate PSI
O-RING
land sequencing and low leakage.
HIGH PRESSURE
Spools are interchangeable to meet SOLENOID TUBES
changing requirements.
Potential leakage is reduced by tapered
High pressure solenoid tubes (HPT option) o-ring counterbores which assure seal
LOW POWER REQUIREMENTS make the D03 ideal for use in higher retention in high flow applications.
On solenoid models, efficient low pressure “series” circuits.
power requirements reduce energy
consumption.
Holding power requirements are only
20 Watts for 115 Volt A.C. or 28 Watts
for 12 or 24 Volt D.C. solenoids.

2
 D03 PATTERN

SPECIFICATIONS ELECTRICAL DATA

General
For a description of spools,operator Input Inrush Holding Holding Coil
Frequency
Solenoid Code➀ Voltage Current Current Power Resistance
functions, electrical options and (Hz)
(Volts) (Amps) (Amps) (Watts) (Ohms ± 10%)
operating recommendations, refer to
dynexdcvoperating.pdf. 24/DF 24 A.C. 50 9.50 2.60 27 1.67
(Dual Frequency) 24 A.C. 60 8.60 1.75 22 1.67
Mounting
Subplate, N.F.P.A. D03 (CETOP 3) 115/DF 110 A.C. 50 1.65 .47 20 40.00
pattern (Dual Frequency) 115 A.C. 60 1.55 .40 20 44.00

Operator Options 230/DF 220 A.C. 50 .86 .22 20 150.00

(Dual Frequency) 230 A.C. 60 .80 .18 20 150.00
6100 Series:Manual Lever;
6500 Series: Direct Solenoid; 460/DF 440 A.C. 50 .40 .13 23 600.00
6800 Series: Hydraulic Piloted; (Dual Frequency) 460 A.C. 60 .41 .10 21 600.00
6900 Series: Air Piloted 12 VDC 12 D.C. — — — 28 5.10
Rated Flow 24 VDC 24 D.C. — — — 28 20.60
Nominal: 8 U.S. gpm (30 L/min); 12VDC EPW 12 D.C. — — — 33 4.36
Maximum: 15 U.S. gpm (57 L/min)
24VDC EPW 24 D.C. — — — 33 17.50
Maximum flow for models using a
Type 011 spool is 9 U.S. gpm 110/50 EPW 110 A.C. 50 1.86 .54 23 35.20
(34 L/min) for solenoid models and 115/60 EPW 115 A.C. 60 1.90 .50 23 33.50
10 U.S. gpm (38 L/min) for air and ➀ Ordering Codes shown are for standard wire leads with wiring box. “Plug-In-Terminal” solenoids
hydraulic pilot operated model. See (Hirschmann GDM 209) are also available; see “Typical Model Code” on page 17.
flow capacity curves on page 4.
Rated Pressure
5000 psi (350 bar)
Tank Port Pressure (Maximum)
Standard: Electrical Connections UL Classification:
1500 psi (105 bar); Standard Wiring Box with leads; Class I, Group C,D;
High Pressure Option (“HPT”): Optional Terminal Strip, Cable Grip Class II, Group E,F,G
A.C., 2300 psi (160 bar); or Pin Connector (N.F.P.A. CSA/UL Recognized (“C” Option)
D.C., 3000 psi (210 bar) standard T3.5-29-1980; A.N.S.I. Solenoid coils are printed with
standard B93,55M-1981); the symbol:
Response Time (Full Stroke)
Optional Plug-In-Terminal Solenoids
Solenoid Energized: fit DIN Connector Standard 4365 C
®
(CSA and UL Recognized)
A.C., 12 ms; D.C., 20 ms (Hirschmann GDM 209) Available with 115/DF coils only. For
Spring Returned:
Explosion Proof Option (“EPW”) other voltages, contact the Dynex
A.C., 15 ms; D.C., 20 ms
Solenoids with special enclosures sales department.
Solenoids
are approved by UL and CSA for use
Models are available with A.C. or D.C. in hazardous locations. Available with
solenoids. A.C. or D.C. solenoids.
The table above shows electrical
specifications for these valves.

MANUAL OPERATED MODELS

A12 or B12
Lever operated models offer handle
position flexibility with four positions
on either port “A” end or port “B” end A9
or
of valve. B9
A3
In-the-field changes are easy, by or
B3
removing the bracket assembly and
rotating the handle to the desired
position. A6 or B6
To specify position, see “Typical Handle Position Viewed from
Model Code” on page 8 and refer to Port “A” or Port “B” End of Valve
the drawing at right.

3
 D03 PATTERN

Typical Valve FLOW CAPACITY

Performance
BAR PSI

SOLENOID MODELS 350 5000 A

300 BC H J K
The flow capacity curves show typical

PRESSURE
4000
performance for each spool type. The 250 DE F G
200 3000
letters in the “Flow Curve Reference”
table identify the appropriate curve. 150 2000
100
1000
50
LEVER OPERATED MODELS 0
U.S. GPM 2 4 6 8 10 12 14 16
Most manual models are rated for
15 U.S. gpm (57 L/min) maximum. L/MIN. 10 20 30 40 50 60
The exception is model 613011-D03 FLOW
which is rated for 13 U.S. gpm
(49 L/min) maximum. This model
has a Code 3 internal operator (two
position, detented operation) with
Type 011 spool (tandem center). FLOW CURVE REFERENCE

Solenoid Spool Type

PILOT OPERATED MODELS Type 0 1 3 4 011 2 2R 32 32R 36 03
The maximum flow for pilot operated
A.C. A A H A C E E J J B B
models is dependent on pilot
pressure. D.C. and “EPW” A A A A D K K F F G A
Generally, the maximum flow for most
pilot operated models is 15 U.S. gpm
(57 L/min). When using a Type 011
spool (tandem center, open cross-
over), the maximum flow rating is MINIMUM PILOT PRESSURE
10 U.S. gpm (38 L/min).
Minimum Pilot Pressure Pilot Pressure At:
The table shows the minimum Spool 5 U.S. gpm 8 U.S. gpm 15 U.S. gpm
Series
pressure required to shift the spool, Type (19 L/min) (30 L/min) (57 L/min)
for various flow capacities. psi bar psi bar psi bar
These values are based on zero tank 0 130 9,0 165 11,4 200 13,8
pressure. As back pressure 1 150 10,3 165 11,4 420 29,0
increases above zero, the minimum 3 145 10,0 165 11,4 180 12,4
pilot pressure must be increased 6800 Series 4 130 9,0 165 11,4 200 13,8
equally. Hydraulic 011 190 13,1 275 19,0 — —
Maximum Pilot Pressure Piloted 2 or 2R 190 13,1 275 19,0 — —
32 or 32R 150 10,3 200 13,8 — —
Hydraulic Piloted, 3000 psi (210 bar);
36 150 10,3 200 13,8 350 24,1
Air Piloted, 200 psi (14 bar)
03 130 9,0 165 11,4 200 13,8
Volume 0 25 1,7 28 1,9 33 2,3
Maximum required to shift spool 1 21 1,4 22 1,5 24 1,7
full stroke: 3 25 1,7 28 1,9 34 2,3
Hydraulic, 0.014 in3 (0,23 cm3); 6900 Series 4 25 1,7 28 1,9 33 2,3
Air, 0.220 in3 (3,61 cm3) Air 011 23 1,6 40 2,8 — —
Piloted 2 or 2R 23 1,6 40 2,8 — —
32 or 32R 25 1,7 30 2,1 — —
36 25 1,7 28 1,9 34 2,3
03 25 1,7 28 1,9 33 2,3

4
 D03 PATTERN

VALVE EFFICIENCY PRESSURE DROP (∆P)

D03 valves provide exceptionally low
pressure drop, as shown in the A B
BAR PSI
performance curves. C
16
Large internal flow paths, with tank 225 D
retur n pressure boost, increase 14 200 E
available shifting forces for depen-
dable high flow operation. 12 175
F

PRESSURE
10 150
G
DETERMINING PRESSURE DROP
125
The curves show resistance to flow 8
for various spool types. The table 100
6
identifies the proper pressure drop 75
curve for each spool and flow path. 4
50

AN EXAMPLE 2 25

In the table under spool Type 1, 0

curve “C” is called out to determine U.S. GPM 2 4 6 8 10 12 14 16
the pressure drop for P→A. Looking
L/MIN. 10 20 30 40 50 60
at the curves, “C” indicates a drop of
FLOW
about 55 psi at 8 U.S. gpm (3,8 bar
at 30 L/min).
To determine total “loop” drop, the
individual pressure drops for P→A
and B →T (or P→B and A→T) must FLOW CURVE REFERENCE
be added.
For example, curve “F” is used for Flow Spool Type
the return flow B→T for spool Type 1. Path 0 1 3 4 011 2 2R 32 32R 36 03
Curve “F” indicates a pressure drop P→A B C B C C C C B B B B
of 35 psi at 8 U.S. gpm (2,4 bar at
30 L/min). Adding the individual P→B B C B C C C C B B B B
pressure drops results in a “loop” A→T E F F E C C C E F G —
drop through the valve in both B→T E F F E C C C F E G —
directions of 55 + 35 = 90 psi (3,8 +
2,4 = 6,2 bar). P→T — D — — A A A — — — —

Installation
and Dimensions
2.00
(50,8)
.16 (4,1), 1.594
GENERAL VALVE MOUNTING .16 (4,1) DEEP MINIMUM (40,49)
1.30 .19
LOCATING PIN HOLE
(33,0) (4,8)
The mounting surface drawing shows
the minimum flush or raised surface P
required for the N.F.P.A. D03 (CETOP 3) 1.220
pattern. Mounting face must be flat 1.70
B A (30,99)
1.02
within 0.0004 inch/4.0 inches (0,010 (43,2) .20 (25,9)
1.250
(31,75)
(5,1) .61
mm/102 mm) with a surface finish of 32 (15,5)
32 microinch(0,80 µm) AA. (0,80) T
.0004/4.0
.030
Port o-rings are included with all (0,010/102)
.50 (0,76)
.25
valves. Mounting bolts must be .250 (6,35) , 4 PORTS .85
(12,7)
(6,4)
ordered separately; 10-24 U.N.C. (21,6)
#10-24 U.N.C.–2B THREADED
1.19
Threaded x 0.75 inch (19 mm), (30,2) .37 (9,4) DEEP, 4 MOUNTING HOLES

Grade 8 or better; four required.

Recommended mounting torque is
Minimum Mounting Surface, N.F.P.A. D03 (CETOP 3) Pattern
65 lb• in (7,3 N• m) maximum.

5
 D03 PATTERN

SOLENOID MODEL DIMENSIONS #10-24 U.N.C. THREADED x .75 (19,0) LONG MOUNTING BOLTS,
4 REQUIRED; TORQUE: 65 LB • IN ( 7,3 N • M)
1/2-14 N.P.T. STANDARD
ELECTRIC ENTRY, 1 EACH SIDE

Refer to the basic installation drawing MANUAL ACTUATOR PIN SOLENOID A FOR 5.00
TYPE 0, 1, 3, 4, 03,
for typical dimensions common to all 32, 32R, 36 SPOOLS;
(127,0)
SOLENOID B FOR TYPE
D03 valves. 011, 2, 2R SPOOLS SOLENOID B FOR TYPE 0, 1, 3,
4, 03, 32, 32R, 36 SPOOLS;
SOLENOID A FOR TYPE 011,
Dimensions are shown for both A.C. 3.73 2, 2R SPOOLS
(94,7)
and D.C. solenoids; D.C. configuration 2.74
(69,6)
shown printed in gray. .38 1.88
(9,7) (47,8)
Weight (Mass) GRIP

Single Solenoid:
A.C., 3.4 lb (1,5 kg); .94
(23,9)
.13
(3,3) 1.30
.125 (3,18)
LOCATING PIN
.25 1.250 .37
D.C., 3.9 lb (1,8 kg) (6,4) (31,75) (9,4)
1.59
(33,0)
.92 2.51 A.C.
.88 (40,4) (23,4) (63,8)
Double Solenoid: (22,4) CLEARANCE TO
REMOVE COIL
3.53
(89,7)
3.12
(79,2)
D.C.
1.75
A.C., 4.0 lb (1,8 kg); (44,4) 1.68 A.C. 8.54 A.C. SOLENOID
(42,7) (216,9)
D.C., 5.3 lb (2,4 kg) 2.30 D.C. 9.77 D.C. SOLENOID
(58,4) (248,2)

6500 Series, Double Solenoid Models

1/2–14 N.P.T. STANDARD

SOLENOID A FOR TYPE 0, 1, 3, 4 ELECTRIC ENTRY SOLENOID B FOR TYPE 0, 1, 3, 4,
03, 32, 32R, 36 SPOOLS; 1 EACH END 03, 32, 32R, 36 SPOOLS;
SOLENOID B FOR SOLENOID A FOR
TYPE 011, 2, 2R SPOOLS REMOVE PLUG, TYPE 011, 2, 2R SPOOLS
3/8 INCH INTERNAL HEX,
3.73 FOR ACCESS TO THIS END 3.73
(94,7) (94,7)

6.78 A.C. SOLENOID .31 .31 6.78 A.C. SOLENOID

(172,2) (7,9) (7,9) (172,2)
7.39 D.C. SOLENOID 7.39 D.C. SOLENOID
(187,7) (187,7)

6500 Series, Single Solenoid Models

LEADWIRES (4) TYPICAL

EXPLOSION PROOF SOLENOIDS #18 AWG, APPROXIMATELY 18 (457) LONG
1/2-14 N.P.T. STANDARD ELECTRIC ENTRY,
360˚ ROTATABLE WITH BOTTOM OUTLET SUBPLATE GROUNDWIRE (2) TYPICAL #18 AWG
Solenoids with special enclosures (GREEN INSULATION)
1.63 APPROXIMATELY 18 (457) LONG
are approved by UL and CSA for use 2.88 MANUAL (41,4)
(73.2) ACTUATOR PIN
in hazardous locations. Overall NOTE: KEEP AIR GAP
BETWEEN SOLENOID
length of single solenoid models (not AND VALVE BODY CLEAN

shown) is 8.23 inches (209,9 mm). 3.72 SOLENOID A FOR TYPE SOLENOID B FOR TYPE
(94,5) 0, 1, 3, 4, 03, 32, 32R, 0, 1, 3, 4, 03, 32, 32R
Note that spacer plate, part number 36 SPOOLS 36 SPOOLS

10591320, is required when valves 45˚

SOLENOID B FOR
TYPE 011, 2,
SOLENOID A FOR
TYPE 011, 2,
1.13
are mounted on manifolds, side outlet (28,7)
2R SPOOLS 2R SPOOLS

subplates or when used as a pilot GRIP

.74
valve. 1.69 SPACER .13 (18,8)
.88 .37 (42,9) NO. 10591320 (3,3) 1.30
(22,4) (9,4) (33,0) .125 (3,18)
Valves can be mounted without .25 LOCATING PIN
1.250 #10-20 U.N.C. THREADED 1.59 .92
removing nameplate. Openings in (6,4) (31,75) x 1.50 (38,1) LONG (40,4) (23,4)
nameplate provide access to 1.75
(44,4) CLEARANCE TO
MOUNTING BOLTS,
4 REQUIRED,
3.53 4.45
(89,7) (113,0)
mounting holes in valve body. REMOVE COIL TORQUE: 65 LB • IN (7,3 N • M)
3.43 12.43
Weight (Mass) (87,1) (315,7)
SOLENOID POSITION LIMIT
Single Solenoid: 8.3 lb (3,8 kg); WITH SIDE OUTLET SUBPLATE
Double Solenoid: 14.0 lb (6,4 kg)
6500 Series, Double “EPW” Solenoid Models

6
 D03 PATTERN

HANDLE POSITION FOR P TO A HANDLE POSITION FOR P TO B

MANUAL OPERATED MODELS FOR TYPE 0, 1, 3, 4, 03, 32
14.5° 14.5° FOR TYPE 0, 1, 3, 4, 03, 32, .625
32R, 36 SPOOLS; P TO B 32R, 36 SPOOLS; P TO A FOR
FOR TYPE 011, 2, 2R SPOOLS (15,88)
Manual models are lever actuated, TYPE 011, 2, 2R SPOOLS

with handle positioned in a choice of

four positions on either port “A” or
por t “B” end of valve. Refer to HANDLE POSITION
FOR P TO B FOR
drawing on page 3 and “Typical TYPE 0, 1, 3, 4 03,
32, 32R, 36 SPOOLS;
Model Code” on page 8. P TO A FOR TYPE
011, 2, 2R SPOOLS 5.45
Valves can be mounted without .94
(138,4)

removing nameplate. Openings in (23,9)

.38
nameplate provide access to mounting (9,7)
2.09
holes in valve body. (53,1)
GRIP 1.44
(36,6)

Weight (Mass)
1.30
3.2 lb (1,5 kg) (33,0) .37 1.250 .25
.125 (3,18) 1.594
LOCATING PIN .92 (9,4) (31,75) (6,4)
(40,49) (23,4)
3.53 .88
(89,7) (22,4)
4.03 .609 1.75
(102,4) (15,47) (44,4)
5.21
(132,3) #10-24 U.N.C. THREADED x
5.83 WITH HANDLE OFFSET .75 (19,0) LONG MOUNTING BOLTS,
(148,1) 4 REQUIRED;
TORQUE: 65 LB • IN ( 7,3 N • M)

6100 Series, Manual Lever Operated

HYDRAULIC PILOTED MODELS

Single and double actuator models PILOT A FOR TYPE 0, 1, 3, 4, PILOT B FOR TYPE 0, 1, 3, 4,
03, 32, 32R, 36, SPOOLS; 03, 32, 32R, 36, SPOOLS;
are available. Overall length of single PILOT B FOR
6.46
PILOT A FOR
(164,1)
configuration (not shown) is 5.25 TYPE 011, 2, 2R SPOOLS
3.53 1.47 TYPE 011, 2, 2R SPOOLS
(89,7) (37,3)
inches (133,4 mm). .88
(22,4)
HEX
Valves can be mounted without .94
(23,9) .38
removing nameplate. Openings in 2.11 (9,7)
GRIP
nameplate provide access to mounting (53,6)

holes in valve body.

.13
(3,3) ∅ .125 (3,18) .37
Refer to page 3 for required shifting 1.30
LOCATING PIN (9,4) 1.250 .25
#10-24 U.N.C. THREADED x (33,0) (31,75) (6,4)
pressure and volume. .75 (19,0) LONG MOUNTING BOLTS, PILOT PORT (2) .88
1.59 .92
4 REQUIRED, NO. 4 S.A.E. (22,4)
(40,4) (23,4
Weight (Mass) TORQUE: 65 LB•IN (7,3 N•M) 1.75
(44,4)
Single Actuator: 2.5 lb (1,1 kg);
Double Actuator: 2.8 lb (1,3 kg) 6800 Series, Double Hydraulic Piloted Models

AIR PILOTED MODELS

PILOT A FOR TYPE 0, 1, 3, 4, PILOT B FOR TYPE 0, 1, 3, 4,
Single and double actuator models 03, 32, 32R, 36 SPOOLS; 03, 32, 32R, 36 SPOOLS;
PILOT B FOR TYPE 011, PILOT A FOR TYPE 011,
are available. Overall length of single 2, 2R SPOOLS 7.09 2, 2R SPOOLS
(180,1)
configuration (not shown) is 5.56 3.53 1.78
PILOT PORT (2) 1/8-27 N.P.T.
inches (141,2 mm). (89,7) (45,2)

Valves can be mounted without .94

(23,9) .38
removing nameplate. Openings in 2.11 (9,7)
nameplate provide access to mounting (53,6) GRIP

holes in valve body. 1.25

(31,8) .13
Refer to page 3 for required shifting HEX (3,3) 1.30 ∅ .125 (3,18)
.37
(9,4) 1.250 .25
(33,0) LOCATING PIN
pressure and volume. #10-24 U.N.C. THREADED x .75 (19,0) .88
(31,75) (6,4)
LONG MOUNTING BOLTS, 4 REQUIRED, 1.59 .92
(22,4)
Weight (Mass) TORQUE: 65 LB •IN (7,3 N •M) (40,4) (23,4)
1.75
(44,4)
Single Actuator: 2.3 lb (1,0 kg);
Double Actuator: 2.5 lb (1,1 kg) 6900 Series, Double Air Piloted Models

7
 D03 PATTERN

Typical Model Code

6 5 4 0 — D03 — 115/DF — R — ✳ — SL — 1 0

Valve Type Valve Size Reverse Flow Operator Modification

6 — Subplate D03 — 8 U.S. gpm (30 L/min) (Code 4 and 6 Only) Number
Mounted Nominal Flow, R — Code 4: Two Position;
Directional N.F.P.A. D03 Spring Centered, Actuator
Control (CETOP 3) Pattern Offset (Reverse Flow) Design
Code 6: Two Position; Number
Spring Offset (Reverse
Flow), Actuator Centered

Actuator
1 — Manual Lever
5 — Solenoid Operated Lever Position (Manual Models Only)
8 — Hydraulic Piloted
9 — Air Piloted A12 — 12 o’clock position, on port “A” end of valve
A9 — 9 o’clock position, on port “A” end of valve
A6 — 6 o’clock position, on port “A” end of valve
A3 — 3 o’clock position, on port “A” end of valve
B12 — 12 o’clock position, on port “B” end of valve
Internal Operator B9 — 9 o’clock position, on port “B” end of valve
B6 — 6 o’clock position, on port “B” end of valve
1 — Two Position; Spring Offset (P→B), Actuator B3 — 3 o’clock position, on port “B” end of valve
Offset (P→A)
2 — Two Position; Spring Offset (P→A), Actuator
Offset (P→B)
3 — Two Position; Actuator Offset, Detented for
Non-Manual Actuators➀ Options (Solenoid Models Only)
Three Position; Detented for Manual Lever
4 — Two Position; Spring Centered, Actuator Offset ➁ C — CSA and UL Recognized Coils (Etched with Symbol)➀
5 — Three Position; Spring Centered, Actuator Offset M — Hand Actuated Manual Override ➁
6 — Two Position; Spring Offset, Actuator Centered➁ T — Terminal Strip➁➂
7 — Manual Lever Only; Two Position, Detented CG — Cable Grip, for .38 to .44 inch (9,5 to 11,1 mm) O.D.
machine tool cable➁➂
➀ Only available with Type 0, Type 1 and Type 03 spools. SL — Solenoid Lights (Available 115/DF A.C. Only)➁➂
➁ Not available with Manual Lever Operated valves. HPT — High Pressure Tank Port
2300 psi (160 bar) maximum A.C. models
3000 psi (210 bar) maximum D.C. models
BH3A — 3-pin Connector (N.F.P.A. standard T3.539-1980), for
single solenoid models, on port “A” end of valve➁➂➃
BH3B — 3-pin Connector, for single solenoid models, on port
Spools “B” end of valve➁➂➃
A B A B BH5A — 5-pin Connector, for single or double solenoid models,
0 2➀ on port “A” end of valve➁➂➃
BH5B — 5-pin Connector, for single or double solenoid models,
P T P T
on port “B” end of valve➁➂➃
A B A B
➀ Available with 115/DF solenoids only. For other voltages, consult the
1 2R➀ Dynex sales department
P T P T ➁ Option not available with “EPW” solenoid models.
A B A B ➂ Option not available with “Plug-In-Terminal” solenoid models.
➃ N.F.P.A. standard T3.539-1980; A.N.S.I. standard B93.55M-1981.
3➀ 32➀
P T P T

A B A B

4➀ 32R➀ Electrical – Solenoid Options

P T P T

A B A B
STANDARD SOLENOIDS: PLUG-IN TERMINAL SOLENOIDS:➀
24/DF — Dual Frequency, 24/60, 24/50 115/HAC — Dual Frequency, 115/60, 110/50
011➀➁ 36➀ 115/DF — Dual Frequency, 115/60, 110/50 230/HAC — Dual Frequency, 230/60, 220/50
P T P T 230/DF — Dual Frequency, 230/60, 220/50 12/HDC — Direct Current, 12 Volts
A B
460/DF — Dual Frequency, 460/60, 440/50 24/HDC — Direct Current, 24 Volts
12VDC — Direct Current, 12 Volts
03 24VDC — Direct Current, 24 Volts
P T 12VDC EPW — Explosion Proof Solenoids
24VDC EPW — Explosion Proof Solenoids
➀ Not available with Type 3 Internal Operators (except manual 115/60 EPW — Explosion Proof Solenoids
lever models). 110/50 EPW — Explosion Proof Solenoids
➁ Open crossover 220/50 EPW — Explosion Proof Solenoids
For Other Voltages, Consult the Dynex Sales Department

➀ Fits DIN Connector Standard 43650 (Hirschmann GDM 209)