Data sheet

HPE Aruba Networking

570 Series Wireless Access Points
High performance Wi-Fi 6 (802.11ax) for outdoor environments

Weatherproof and temperature hardened, HPE Aruba Networking

570 Series access points deliver the highest Wi-Fi 6 performance
in outdoor and environmentally challenging locations. The
high‑performance and high power 570 Series APs deliver
maximum capacity and range. It delivers 4x4:4SS MU-MIMO
capability, HPE Aruba Networking’s advanced ClientMatch
and integrated Bluetooth to enable HPE Aruba Networking
location services.
Purpose-built to survive in the harshest outdoor Incredible efficiency
environments, 570 Series APs withstand exposure to
extreme high and low temperatures, persistent moisture The 570 Series APs are designed to optimize
and precipitation, and are fully sealed to keep out user experience by maximizing Wi-Fi efficiency
airborne contaminants. All electrical interfaces include and dramatically reducing airtime contention
industrial strength surge protection. between clients.

Features include Uplink and Downlink Orthogonal

HPE Aruba Networking Wi-Fi 6 access points provide
Frequency Division Multiple Access (OFDMA), Downlink
high-performance connectivity in dense mobile and
Multi-User MIMO (MU-MIMO) and cellular co-location.
IoT environments. With maximum aggregate on air
With up to 4 spatial stream and 160 MHz channel
data rates of 3 Gbps (HE80/HE40), the 570 Series
capability, the 570 Series provides groundbreaking
APs deliver the speed and reliability needed for
wireless capabilities for any application.
demanding environments.
Read the Multi-User 802.11ax white paper for
further information.
Data sheet Page 2

Advantages of OFDMA HPE Aruba Networking

This capability allows HPE Aruba Networking Wi‑Fi
6 APs to handle multiple Wi-Fi 6 enabled clients
secure infrastructure
simultaneously on a single radio. Channel utilization The HPE Aruba Networking 570 Series is an integral
is optimized per transaction by matching allocated part of HPE Aruba Networking’s Zero Trust security
bandwidth in a channel to the offered user load. These approach to help protect user authentication and
subdivisions of the channel are referred to as Resource wireless traffic. Select capabilities include:
Units (RU).
WPA3 and Enhanced Open
Multi-user MIMO (MU-MIMO) With the introduction of WPA3 and Enhanced Open,
The 570 Series APs support downlink MU-MIMO similar a Wi-Fi 6 certified client will never send unencrypted
to Wi-Fi 5 (802.11ac Wave 2) APs. With the introduction traffic over the air. Even with an open authenticated
OFDMA in Wi-Fi 6, the overhead for this capability is network, Enhanced Open still provides strong
reduced and MU-MIMO effectiveness is substantially encryption over the air.
improved for large client counts.
In all Wi-Fi 6 user sessions, each user is uniquely
Wi-Fi 6 and MU-MIMO aware client optimization encrypted and if they disconnect and reconnect, the
HPE Aruba Networking’s patented AI powered encryption changes from session to session.
ClientMatch technology ensures that all clients are
attached to their best serving Access Point. Session WPA2-MPSK
metrics, network metrics, applications and client type are MPSK enables simpler passkey management for WPA2
used to identify and maintain the best connection. devices—should the Wi-Fi password on one device
change, no additional changes are needed for other
Advanced Cellular Coexistence (ACC) devices. This feature is enabled when networks are
The ACC feature uses built in filtering to automatically deployed with ClearPass Policy Manager.
minimize the impact of interference of high power
cellular base stations, in building distributed antenna VPN tunnels
systems as well as small cell and femtocell equipment. In Remote AP (RAP) and IAP-VPN deployments, the
570 Series can be used to establish a secure SSL/IPSec
Intelligent Power Monitoring (IPM) VPN tunnel to a Gateway or Mobility Controller that is
HPE Aruba Networking APs continuously monitor configured as a VPN concentrator.
and report hardware energy consumption. APs can be
configured to enable or disable capabilities based on the Trusted Platform Module (TPM)
available PoE power—ideal when wired switches have For enhanced device assurance, all PE Aruba
exhausted their power budget. Networking APs have an installed TPM for secure
storage of credentials and keys, and boot code.
IOT platform capabilities
HPE Aruba Networking Wi-Fi 6 APs include an
Simple and secure access
integrated Bluetooth 5 and 802.15.4 radio (for Zigbee To simplify policy enforcement, the HPE Aruba
support) to simplify deploying and managing IoT-based Networking 570 Series uses HPE Aruba Networking’s
location services, asset tracking services, security Policy Enforcement Firewall (PEF) to encapsulate all
solutions and IoT sensors. This allows organizations traffic from the AP to the Mobility Controller (gateway)
to leverage the 570 Series as an IoT platform, which for end-to-end encryption and inspection. Policies are
eliminates the need for an overlay infrastructure and applied based on context including user role, device
additional IT resources. type, application, and location. This reduces the manual
configuration of SSIDs, VLANs, and ACLs. PEF also
Target Wake Time (TWT) serves as the underlying technology for HPE Aruba
Ideal for IoT solutions that communicate infrequently,
Networking Dynamic Segmentation.
this Wi-Fi 6 capability allows IoT devices to use
802.11ax protocol. TWT coordinates with client devices
to allow them to sleep for extended periods and use High density connectivity
shorter wake times to communicate before returning to
sleep. This substantially extends the useful operating life Each 570 Series AP provide connectivity for a maximum
of Wi-Fi 6 based battery powered sensors. of 512 associated clients per radio (1024 total).
Data sheet Page 3

Flexible operation and management antenna operation

A unique feature of HPE Aruba Networking APs
– 2.4 GHz Two Nf connectors for external
is the ability to operate in either controller-less or
antenna operation
controller‑based mode.
– BLE/Zigbee: Integrated omnidirectional antenna and
Controller-less (instant) mode peak gain of 4.2dBi
In controllerless mode, one AP serves as a virtual
controller for the entire network. Learn more about • AP-575
Instant mode in this technology brief.
– Built in Omni Directional Antennas
Mobility controller mode – 5 GHz Antennas 5dBi
For optimized network performance, roaming and
– 2.4GHz Antennas 3.4dBi
security, APs tunnel all traffic to a mobility controller for
centrally managed traffic forwarding and segmentation, – BLE/Zigbee: Integrated omnidirectional antenna and
data encryption, and policy enforcement. Learn more the peak gain of 6dBi
in the HPE Aruba Networking Operating System
data sheet. • AP-577
– Built in 90°H x 90°V Directional Antennas
Management options
Available management choices include HPE Aruba – 5 GHz Antennas 5.6dBi
Networking Central (cloud-based) or HPE Aruba – 2.4 GHz Antennas 6.8dBi
Networking AirWave (multi-vendor, on prem) solutions.
– BLE/Zigbee: Integrated omnidirectional antennas
For large installations across multiple sites, HPE Aruba with peak gain of 8.4dBi
Networking APs can be shipped and activated with
Zero Touch Provisioning through Central or AirWave. Wi-Fi radio specifications
This reduces deployment time, centralizes configuration, • AP type: Outdoor Hardened, Wi-Fi 6 dual radio, 5 GHz
and provides inventory visibility. 4x4 MIMO and 2.4 GHz 2x2 MIMO
• Software-configurable dual radio supports 5 GHz
Additional Wi-Fi features (Radio 0) and 2.4 GHz (Radio 1) 5 GHz.
• Four spatial stream Single User (SU) MIMO for up to
Transmit Beamforming (TxBF) 4.8 Gbps wireless data rate to individual 4SS HE160
Increased signal reliability and range Wi-Fi 6 client device (max)
Passpoint Release 2 • Two spatial stream Single User (SU) MIMO for up to
Seamless cellular-to-Wi-Fi carryover for guests 1.2 Gbps wireless data rate to individual 2SS HE80
Wi-Fi 6 client device (typical)
Dynamic Frequency Selection (DFS)
• Four spatial stream Multi User (MU) MIMO for up to
Optimized use of available RF spectrum
4.8 Gbps wireless data rate to up to four 1SS or two
2SS HE160 Wi-Fi 6 DL-MU-MIMO capable client
Maximal Ratio Combining (MRC)
devices simultaneously (max)
Improved receiver performance for multi antenna
access points • Four spatial stream Multi User (MU) MIMO for up
to 2.4 Gbps wireless data rate to up to four 1SS or
Cyclic Delay/Shift Diversity (CDD/CSD) two 2SS HE80 Wi-Fi 6 DL-MU-MIMO capable client
Enable use of multiple transmit antennas devices simultaneously (typical)
2.4 GHz
Space-Time Block Coding (STBC)
Increased connection robustness • Two spatial stream Single User (SU) MIMO for up to
575 Mbps wireless data rate to individual 2SS HE40
Low-Density Parity Check (LDPC) Wi-Fi 6 client device (max)
High performance error detection and correction coding • Two spatial stream Single User (SU) MIMO for up to
for enhanced receiver performance 287 Mbps wireless data rate to individual 2SS HE20
Wi-Fi 6 client device (typical)
AP-570 Series specifications • Support for up to 512 associated client devices per
radio, and up to 16 BSSIDs per radio
Hardware variants
• Supported frequency bands (country-specific
• AP-574
restrictions apply):
– 5 GHz: Four Nf connectors for external
Data sheet Page 4

– 2.400 to 2.4835 GHz (ISM) NSS = 1 to 4, HE20 to HE160)

– 5.150 to 5.250 GHz (U-NII-1) • 802.11n/ac/ax packet aggregation: A-MPDU, A-MSDU

• Transmit power: Configurable in increments of
– 5.250 to 5.350 GHz (U-NII-2A)
0.5 dBm
– 5.470 to 5.725 GHz (U-NII-2C) • Maximum (conducted) transmit power (limited by local
regulatory requirements):
– 5.725 to 5.850 GHz (U-NII-3/ISM)
– 2.4 GHz band: +22 dBm per chain, +25 dBm
– 5.850 to 5.875 GHz (U-NII-4) aggregate (2x2)
– 5 GHz band: +22 dBm per chain, +28 dBm aggregate
• Available channels: Dependent on configured (2x2)
regulatory domain
– Note: conducted transmit power levels exclude
• Dynamic frequency selection (DFS) optimizes the use antenna gain.
of available RF spectrum
• Supported radio technologies: • Maximum EIRP (limited by local regulatory
requirements):
– 802.11b: Direct-sequence spread-spectrum (DSSS)
– 2.4 GHz band:
– 802.11a/g/n/ac: Orthogonal frequency-division
multiplexing (OFDM) à 574: 25 + Antenna Gain + TxBF Gain

– 802.11ax: Orthogonal frequency-division multiple à 575: 29.0 dBm EIRP

access (OFDMA) with up to 16 resource units (RU) à 577: 34.4 dBm EIRP
• Supported modulation types: – 5 GHz band:
– 802.11b: BPSK, QPSK, CCK à 574: 28 + Antenna Gain + TxBF Gain
– 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, à 575: 32.6 dBm EIRP
256‑QAM (proprietary extension)
à 577: 36 dBm EIRP
– 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM,
256‑QAM, 1024 QAM (proprietary extension) • Advanced Cellular Coexistence (ACC) minimizes the
– 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, impact of interference from cellular networks
256‑QAM, 1024 QAM • Maximum ratio combining (MRC) for improved
receiver performance
• 802.11n high-throughput (HT) support: HT20/40
• Cyclic delay/shift diversity (CDD/CSD) to enable the
• 802.11ac very high throughput (VHT) support: use of multiple transmit antennas
VHT20/40/80/160
• Short guard interval for 20-MHz, 40-MHz, 80-MHz
• 802.11ax high efficiency (HE) support: and 160-MHz channels
HE20/40/80/160
• Space-time block coding (STBC) for increased range
• Supported data rates (Mbps): and improved reception
– 802.11b: 1, 2, 5.5, 11 • Low-density parity check (LDPC) for high-efficiency
– 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 error correction and increased throughput

– 802.11n (2.4GHz): 6.5 to 300 (MCS0 to MCS15, • Transmit beam-forming (TxBF) for increased signal
HT20 to HT40) reliability and range

– 802.11n (5GHz): 6.5 to 600 (MCS0 to MCS31, HT20 • 802.11mc Fine Timing Measurement (FTM) for
to HT40) precision distance ranging

– 802.11ac: (5 GHz): 6.5 to 3,467 (MCS0 to MCS9, Power

NSS = 1 to 4 for VHT20 to VHT160) • Maximum (worst-case) power consumption:
– 802.11ax (2.4GHz): 8.6 to 574 (MCS0 to MCS11, – PoE powered (dual ports): 32.0W
NSS = 1 to 2, HE20 to HE40)
– PoE powered (single port, full function): 26.1W
– 802.11ax (5GHz): 8.6 to 4803 (MCS0 to MCS11,
Data sheet Page 5

• Maximum (worst-case) power consumption in idle • Visual indicator (multi-color LED): For system and
mode: 14.0W (single PoE) or 16.0W (dual PoE) radio status
• Maximum (worst-case) power consumption in • Reset button: Factory reset (during device power up)
deep‑sleep mode: 2.9W (single PoE) or 3.9W
• USB-C console interface
(dual PoE)
• The AP supports Power over Ethernet (PoE; on port Mounting
E0 and/or E1) • Optional mounting kits:
• When PoE power is supplied to both Ethernet ports, – AP-OUT-MNT-V1A: Outdoor Pole/Wall Long
the AP can be configured to combine or prioritize Mount Kit
power sources
– AP-270-MNT-V2: Outdoor Pole/Wall Short Mount Kit
• Power sources are sold separately; see the ordering
– AP-270-MNT-H1: Outdoor AP Hanging or Tilt Install
Information section below for details
Mount Kit
• When powered by 1x 802.3at (class 4) PoE and with
– AP-270-MNT-H2: Outdoor Flush Wall or
the IPM feature disabled, the AP will disable the other
Ceiling Mount
Ethernet port. In the same configuration but with IPM
enabled, the AP will start up in unrestricted mode, but – AP-270-MNT-H3: Outdoor AP Hanging or Dual-Tilt
may dynamically apply restrictions depending on the Install Mount Kit
PoE budget and actual power. The feature restrictions
and order can be programmed. Mechanical
• AP-574
• Operating the AP with single or dual 802.3af (class 3
or lower) PoE source is not supported. – Dimensions/weight (excluding mount):
à 24 cm (W) x 24 cm (D) x 19 cm (H)/9.4” (W) x
Additional Interfaces
9.4” (D) x 7.5” (H)
• E0: HPE SmartRate port (RJ-45)
à 2.7 kg/6.0 lbs
– Auto-sensing link speed (100/1000/2500BASE-T)
and MDI/MDX • AP-575
– 2.5Gbps speed complies with NBase-T and – Dimensions/weight (excluding mount):
802.3bz specifications
à 24 cm (W) x 24 cm (D) x 27 cm (H)/9.4” (W) x
– PoE-PD: 48Vdc (nominal) 802.3at/bt (Class 4 9.4” (D) x 10.6” (H)
or higher)
à 2.5 kg/5.6 lbs
– 802.3az Energy Efficient Ethernet (EEE)
• AP-577
• E1: 100/1000BASE-T (RJ-45)
– Dimensions/weight (excluding mount):
– Auto-sensing link speed and MDI/MDX
à 23 cm (W) x 22 cm (D) x 14 cm (H)/9.0” (W) x 8.7”
– 802.3az Energy Efficient Ethernet (EEE) (D) x 5.6” (H)
– PoE-PD: 48Vdc (nominal) 802.3at/bt (Class 4 à 2.1 kg/4.6 lbs
or higher)
Environmental
• Link Aggregation (LACP) support between both • Operating:
network ports for redundancy and increased capacity
– Temperature: -40° C to +65° C (-40° F to +149° F)
• Bluetooth 5 and 802.15.4 radio with full solar loading
– 2.4 GHz – Humidity: 5% to 93% non-condensing internal
– Bluetooth 5: up to 8dBm transmit power and -95dBm – Rated for operation in all weather conditions
receive sensitivity
– Zigbee: up to 8 dBm transmit power and -97dBm • Storage and transportation:
receive sensitivity – Temperature: -40° C to +70° C (-40° F to +158° F)
– Up to 4dBm transmit power (class 2) and -91 dBm
receive sensitivity • Operating Altitude: 3,000 m
• Water and Dust
Data sheet Page 6

– IP66/67 Warranty
• Salt Tolerance HPE Aruba Networking's hardware limited
– Tested to ASTM B117-07A Salt Spray 200hrs lifetime warranty.

• Wind Survival: Up to 165 Mph Minimum operating system software

• Shock and Vibration ETSI 300-19-2-4 • HPE Aruba Networking Operating System and HPE
Aruba Networking InstantOS 8.7.0.0
Regulatory
• FCC/ISED • HPE Aruba Networking Operating System 10.2.0.0
• CE Marked
• RED Directive 2014/53/EU
• EMC Directive 2014/30/EU
• Low Voltage Directive 2014/35/EU
• IEC/EN/UL 62368-1
• EN 60601-1-1, EN60601-1-2
• Railway Certs:
– EN 50155:2017—Railway Applications
– EN 50121-1:2017—Railway EMC
– EN 50121-3-2—Railway EMC
– EN 50121-4:2016—Railway Immunity
– IEC 61373 ed2:2008—Railway Shock and Vibration

For more country-specific regulatory information

and approvals, please see your HPE Aruba
Networking representative.

Regulatory model numbers

• AP-574: APEX0574
• AP-575: APEX0575
• AP-577: APEX0577

Certifications
• CB Scheme Safety, cTUVus
• UL2043 plenum rating
• Wi-Fi Alliance certified 802.11a/b/g/n/
• Wi-Fi Alliance certified Wi-Fi 6 (802.11ax)
• Wi-Fi CERTIFIED™ ac (with wave 2 features)
• Passpoint® (Release 2) with HPE Aruba Networking
Operating System and Instant
• Wi-Fi CERTIFIED Location™
Data sheet Page 7

RF performance table
Band, rate Maximum transmit power (dBm) Receiver sensitivity (dBm)
per transmit chain per receive chain

2.4 GHz, 802.11b

1 Mbps 22 -97

11 Mbps 22 -89

2.4 GHz, 802.11g

6 Mbps 22 -94

54 Mbps 20 -76

2.4 GHz, 802.11n/ac HT20

MCS0 22 -93

MCS8 19 -72

2.4 GHz, 802.11ax HE20

MCS0 22 -93

MCS11 17 -62

5 GHz, 802.11a

6 Mbps 22 -95

54 Mbps 20 -76

5 GHz, 802.11n/ac HT20/VHT20

MCS0 22 -94

MCS8 19 -72

5 GHz, 802.11n/ac HT40/VHT40

MCS0 22 -92

MCS9 19 -68

5 GHz, 802.11ac VHT80

MCS0 22 -90

MCS9 19 -65

5 GHz, 802.11ac VHT160

MCS0 22 -84

MCS9 19 -59
Data sheet Page 8

Band, rate Maximum transmit power (dBm) Receiver sensitivity (dBm)

per transmit chain per receive chain

5GHz, 802.11ax HE20

MCS0 22 -94

MCS11 17 -62

5 GHz, 802.11ax HE40

MCS0 22 -91

MCS11 17 -60

5 GHz, 802.11ax HE80

MCS0 22 -87

MCS11 17 -57

5 GHz, 802.11ax HE160

MCS0 22 -85

MCS11 17 -53

Maximum capability of the hardware provided (excluding antenna gain). Maximum transmit power is limited by local regulatory settings.

Ordering information
Part number Description

AP-570 Series Unified Outdoor Access Points

R4H09A HPE Aruba Networking AP-574 (EG) 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H10A HPE Aruba Networking AP-574 (IL) 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H11A HPE Aruba Networking AP-574 (JP) 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H12A HPE Aruba Networking AP-574 (RW) 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H13A HPE Aruba Networking AP-574 (US) 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H14A HPE Aruba Networking AP-575 (EG) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H15A HPE Aruba Networking AP-575 (IL) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H16A HPE Aruba Networking AP-575 (JP) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H17A HPE Aruba Networking AP-575 (RW) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H18A HPE Aruba Networking AP-575 (US) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP
Data sheet

R4H19A HPE Aruba Networking AP-577 (EG) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Directional Antenna Outdoor AP

R4H20A HPE Aruba Networking AP-577 (IL) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Directional Antenna Outdoor AP

R4H21A HPE Aruba Networking AP-577 (JP) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Directional Antenna Outdoor AP

R4H22A HPE Aruba Networking AP-577 (RW) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Directional Antenna Outdoor AP

R4H23A HPE Aruba Networking AP-577 (US) 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Directional Antenna Outdoor AP

AP-570 Series Unified Outdoor Access Points TAA

R4H24A HPE Aruba Networking AP-574 (EG) TAA 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H25A HPE Aruba Networking AP-574 (IL) TAA 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H26A HPE Aruba Networking AP-574 (JP) TAA 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H27A HPE Aruba Networking AP-574 (RW) TAA 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H28A HPE Aruba Networking AP-574 (US) TAA 802.11ax 2x2:2/4x4:4 Dual Radio 6xNf Connectorized Outdoor AP

R4H29A HPE Aruba Networking AP-575 (EG) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H30A HPE Aruba Networking AP-575 (IL) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H31A HPE Aruba Networking AP-575 (JP) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H32A HPE Aruba Networking AP-575 (RW) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H33A HPE Aruba Networking AP-575 (US) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integrated Omni Antenna Outdoor AP

R4H34A HPE Aruba Networking AP-577 (EG) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integ Directional Antenna Outdoor AP

R4H35A HPE Aruba Networking AP-577 (IL) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integ Directional Antenna Outdoor AP

R4H36A HPE Aruba Networking AP-577 (JP) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integ Directional Antenna Outdoor AP

R4H37A HPE Aruba Networking AP-577 (RW) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integ Directional Antenna Outdoor AP

R4H38A HPE Aruba Networking AP-577 (US) TAA 802.11ax 2x2:2/4x4:4 Dual Radio Integ Directional Antenna Outdoor AP

Make the right purchase decision.

Contact our presales specialists.

Contact us
Visit ArubaNetworks.com

© Copyright 2024 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change
without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
All third-party marks are property of their respective owners.
DS_HPEANW570SeriesAP_RVK_032924 a00096370ENW