GHS SAFETY DATA SHEET

MQ-906
Cyanoacrylate Adhesive
SECTION 1 – PRODUCT & COMPANY IDENTIFICATION
PRODUCT NAME: STRONG ‘n’ QUIK MQ-906 Contact Adhesive PRODUCT USE: Adhesive
SUPPLIER: HP ADHESIVES LIMITED ADDRESS: G-11 Unique House, Chakala Road
Andheri (E) Mumbai 400099 INDIA
T: +91 22 2932 4739 F: +91 22 2834 9596
EMERGENCY: Transportation: CHEMTEL Tel. 800.255-3924, 813-248-0585 (International) MEDICAL: Tel. 800.451.8346, 760.602.8703 3E Company (International)

SECTION 2 – HAZARDIOUS IDENTIFICATION

Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008
Skin irritation H315 Causes skin irritation. Category 2
Serious eye irritation H319 Causes serious eye irritation Category 2
Specific target organ H335 May cause respiratory irritation Category 3
toxicity-single exposure

Label elements (CLP): Labelling according to Regulation (EC) No 1272/2008

Hazard pictogram:
Single word: Warning
Hazard statement: H315 Causes skin irritation.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.
Cyanoacrylate. Danger. Bonds skin and eyes in seconds. Keep out of the reach of children.
Precautionary statement: P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
P302+P350 If on skin: Wash with plenty of soap and water.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.
Other hazards: None if used properly.

SECTION 3 – COMPOSITION / INFORMATION ON INGREDIENTS

General chemical description: Cyanoacrylate Adhesive
Base substances of preparation: Cyanoacrylate

Declaration of the ingredients according to CLP (EC) No 1272/2008:

Hazardous components EINECS Number / Index Number / Content Classification
CAS-No. REACH-Reg No.
Ethyl 2-cyanoacrylate 7085-85-0 230-391-5 / 607-236-00-9 / 01- >90-<100% Skin irritation 2 H315
2119527766-29-0002 Serious eye irritation 2 H319
Specific target organ toxicity – single exposure 3 H335
For full text of the H – statements and other abbreviations see section 16 “Other information”.

SECTION 4 – FIRST AID MEASURES

Description of first aid measures
Inhalation: Don’t breathe gas/fumes/vapor/spray (appropriate wording to be specified by the manufacturer). (S23)
Evacuate from further exposure. If unconsciousness occurs, seek immediate medical assistance and call a physician.
If the breath has stopped, have artificial respiration. If breathing difficulty occurs, have oxygen inhalation.
Skin contact: Instantly wash affected parts of the body with water and soap and rinse thoroughly.
Seek medical treatment and present this data sheet.
Eye contact: In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. (S26)
Ingestion: Ensure that breathing passages are not obstructed. The product will polymerize immediately in the mouth making it almost impossible to swallow.
Saliva will slowly separate the solidified product from the mouth.

Most important symptoms and effects, both acute and delayed

May cause allergy or asthma symptoms or breathing difficulties if inhaled.
Eye: Irritation, conjunctivitis.
Skin: Redness, inflammation.
Respiratory: Irritation, coughing, shortness of breath, chest tightness.

Indication of any immediate medical attention and special treatment needed

In the case of lung irritation: Primary treatment using corticoide spray, eg. Auxiloson spray, Pulmicort-dosage-spray. (Auxiloson and Pulmicort are registered trademarks).

HP ADHESIVES LIMITED
+91-22-68196300 [email protected] www.hpadhesives.com 11, Unique House, Chakala Rd,
Andheri (East), Mumbai - 400 099.
 GHS SAFETY DATA SHEET
MQ-906
Cyanoacrylate Adhesive
SECTION 5 – FIREFIGHTING MEASURES
Extinguishing media
Suitable extinguishing media: Alcohol-resistant foam, dry powder, carbon dioxide, water spray jet.
Unsuitable extinguishing media: High volume water jet.

Special hazards arising from the substance or mixture

In the event of fire, the following can be released: Nitrogen oxides (NOx), carbon monoxide (CO), carbon dioxide (CO2).

Advice for firefighters

In case of fire and/or explosion do not breathe fumes. Firefighters should wear positive pressure self-contained breathing apparatus (SCBA). Firefighting operations,
rescue and cleaning work under effect of combustion and smolder gases just may be done with breathing apparatus. Dispose of contaminated extinction water
according to official regulations.

SECTION 6 - ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
For non-emergency personnel: Use personal protective clothing.
For emergency responders: Ensure adequate ventilation. Avoid contact with eyes or skin.

Environmental precautions
If leakage occurs, dam up. Resolve leaks if this possible without risk. Prevent surface and ground-water infiltration, as well as ground penetration. Prevent from entering
drainage system. If accidental entry into drainage system occurs, inform responsible authorities.

Methods and material for containment and cleaning up

Do not use cloth for clean-up. Flood with water to complete polymerization and scrape up the polymer. Solid material can be disposed as non-hazardous waste.

Reference to other sections

For personal protective equipment see Section 8 and for disposal instructions see Section 13.

SECTION 7 – HANDLING AND STORAGE

Precautions for safe handling
Recommendations: Avoid contact with eyes, skin and clothing. Avoid breathing vapor and mists. Wash thoroughly after handling. Avoid contact
with fabric and paper goods. Contact with these may cause polymerization that can generate smoke and strong irritating
vapors and can cause thermal burns.
Advice on general Wash hands and face before eating.
occupational hygiene:

Conditions for safe storage, including any incompatibilities

Keep in a cool, well-ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Incompatible products: Do not store
together with alkalis.

Specific end use(s)

Cyanoacrylate

SECTION 8 - PRECAUTIONS TO CONTROL EXPOSURE / PERSONAL PROTECTION

Control parameters
Valid for Great Britain
Basis UK EH40 WELs
Ingredient ppm mg/m3 Type Remarks
Ethyl 2-cyanoacrylate - - TWA (8 h) EH40 WEL
7085-85-0
Ethyl 2-cyanoacrylate 0.3 1.5 Short Term Exposure Limit EH40 WEL
7085-85-0 STEL (15 min)

Exposure controls
Appropriate Engineering Controls: If general ventilation is insufficient to maintain vapor concentration below established exposure limits, use
protective downdraft exhaust ventilation.
Individual protection measures
General protective and hygienic measures: Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash
hands before breaks and at the end of work. Avoid contact with the eyes and skin.
Eye/Face protection Safety glasses with side shields or chemical splash goggles.
Skin protection Do not use PVC, rubber, cotton or nylon gloves.
Hand protection Tested protective gloves are to be worn: Suitable material: Synthetic rubber gloves. In the cases of special
applications, it is recommended to check the chemical resistance with the manufacturer of the gloves.
Respiratory protection If there is a potential to exceed exposure limits, use an approved respirator.
Environmental exposure controls Do not empty into drains or the aquatic environment.

HP ADHESIVES LIMITED
+91-22-68196300 [email protected] www.hpadhesives.com 11, Unique House, Chakala Rd,
Andheri (East), Mumbai - 400 099.
 GHS SAFETY DATA SHEET
MQ-906
Cyanoacrylate Adhesive
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES

Appearance: Liquid, colorless to straw liquid Vapor density (Air=1): Approximately 3

Odor: Sharp, irritating Relative density: 1.1g/cm3
Odor threshold: Not available. Solubility: Polymerizes in presence of water.
pH: Not applicable Partition coefficient: Not applicable
Auto-ignition
Melting point/freezing point: -22℃ 485℃
temperature:
Initial boiling point and Decomposition
>200℃ Not applicable
boiling range: temperature:
Flash point: 80-93.4℃ (Method: Tag closed Cup) Viscosity: 1.8-5 cps.
Evaporation rate (Butyl
Not available. Explosive properties: Product is not explosive.
acetate =1):
Flammability: Not available. Oxidizing properties: Product is not oxidizing.
Upper/lower flammability: Not available Specific gravity: 1.10 (25℃)
Vapor pressure (25℃): Less than 0.2 mmHg VOC content: Less than 2%; 20g/l

SECTION 10 - STABILITY AND REACTIVITY

Reactivity Rapid exothermic polymerization will occur in the presence of water, amines, alkalis, oxidizing agents and alcohols. Stable
under recommended storage conditions.
Chemical stability The product is in compliance with the storage and processing conditions, chemically stable.
Possibility of hazardous reactions Danger of polymerization. Polymerization with evolution of heat.
Conditions to avoid Spontaneous polymerizations.
Incompatible materials Water, amines, alkalis, oxidizing agents and alcohols.
Hazardous decomposition products Carbon monoxide and carbon dioxide. Nitrous oxides (NOx).

SECTION 11 - TOXICOLOGICAL INFORMATION

Information on toxicological effects
Oral toxicity: Cyanoacrylates are considered to have relatively low toxicity. Acute oral LD50 is >5000 mg/kg (rat). It is almost impossible to
swallow as it rapidly polymerizes in the mouth.
Inhalative toxicity: Irritating to respiratory system. Prolonged exposure to high concentrations of vapor may lead to chronic effects in sensitive
individuals. In dry atmosphere with <50% humidity, vapor may irritate the eyes and respiratory system.
Skin irritation: Irritating to the skin. Bonds skin in seconds. Considered to be of low toxicity: acute dermal LD50 (rabbit) >2000mg/kg. Due
to polymerization at the skin surface allergic reaction is unlikely to occur.
Eye irritation: Irritating to eyes. Liquid product will bond eyelids. In a dry atmosphere (RH<50%) vapor may cause irritation and
lachrymatory effect.

Acute toxicity:
Hazardous components Value Type Value Route of application Exposure Species Method
CAS-No. time
Ethyl 2-cyanoacrylate LD50 >5000mg/kg oral rat OECD
7085-85-0 Guideline 401
(Acute Oral Toxicity)
LD50 >2000mg/kg dermal rabbit OECD
Guideline 402
(Acute Dermal Toxicity)

Skin corrosion/irritation
Hazardous components Result Exposure time Species Method
CAS-No.
Ethyl 2-cyanoacrylate Slightly irritating 24 h rabbit OECD Guideline 404
7085-85-0 (Acute Dermal Irritation/Corrosion)

Serious eye damage/irritation

Hazardous components Result Exposure time Species Method
CAS-No.
Ethyl 2-cyanoacrylate Slightly irritating 72 h rabbit OECD Guideline 405
7085-85-0 (Acute Eye Irritation/Corrosion)

HP ADHESIVES LIMITED
+91-22-68196300 [email protected] www.hpadhesives.com 11, Unique House, Chakala Rd,
Andheri (East), Mumbai - 400 099.
 GHS SAFETY DATA SHEET
MQ-906
Cyanoacrylate Adhesive
Germ cell mutagenicity:
Hazardous components Result Type of study/ Metabolic Species Method
CAS-No. Route of activation/
administration Exposure time
Ethyl 2-cyanoacrylate negative Bacterial reverse mutation assay (e.g. with and without OECD Guideline 471
7085-85-0 negative Ames test) mammalian cell gene with and without (Bacterial Reverse Mutation Assay)
negative mutation assay in vitro mammalian OECD Guideline 476
chromosome aberration test (In vitro Mammalian Cell Gene Mutation Test)
OECD Guideline 473
(In vitro Mammalian Chromosome Aberration Test)
Carcinogenicity: According NTP, OSHA and IARC, the substance is not carcinogen.

SECTION 12 - ECOLOGICAL INFORMATION

Toxicity: Biological and chemical oxygen demands (BOD and COD) are insignificant. Do not empty into drains/ surface water/ ground water. Do
not allow uncontrolled leakage of product into the environment.

Persistence and degradability

Hazardous components Result Route of application Degradability Method
CAS-No.
Ethyl 2-cyanoacrylate aerobic 57% OECD Guideline 301 D
7085-85-0 (Ready Biodegradability: Closed Bottle Test)

Bioaccumulative potential
Hazardous components LogKow Bioconcentration Temperature Method
CAS-No. Factor (BCF)
Ethyl 2-cyanoacrylate 0.776 22℃ EU Method A. 8
7085-85-0 (Partition Coefficient)

Mobility in soil Cured adhesives are immobile.

Results of PBT and vPvB The components in this formulation do not meet the criteria for classification as PBT or vPvB.
assessment
Other adverse effects No further relevant information available.

SECTION 13 - WASTE DISPOSAL CONSIDERATIONS

Waste treatment methods

Waste treatment containers: Dispose according local, province/state, country’s governmental regulations.
Appropriate methods of waste treatment of Cured adhesive: Disposal of as water insoluble non-toxic solid chemical in authorized landfill or
substance: incinerate under controlled conditions.
Appropriate methods of waste treatment of packaging: After use, tubes, cartons, and bottles containing residual product should be disposed of as chemically
contaminated waste in an authorized legal land fill site or incinerated. Disposal must be made according
to official regulations.
Sewage disposal: Dispose according local, province/state, country’s governmental regulations.
Special precautions: Not available.
Relevant community/national/regional provisions: Not available.

SECTION 14 - TRANSPORT INFORMATION

ADR/RID AND/ADNR IMDG IATA

UN Number UN 1993 Not available Not available UN 3334
UN Proper Shipping Name COMBUSTIBLE LIQUIDS, N.O.S. Not available Not available AVITATION REGULATED LIQUID, N.O.S.
(Cyanoacrylate ester) (Cyanoacrylate ester)
Transport hazard class(es) 3 Not available Not available 9
Packing group None Not available Not available None
Environmental hazards Not available Not available Not available Not available
Special precautions for user Not available Not available Not available Not available

HP ADHESIVES LIMITED
+91-22-68196300 [email protected] www.hpadhesives.com 11, Unique House, Chakala Rd,
Andheri (East), Mumbai - 400 099.
 GHS SAFETY DATA SHEET
MQ-906
Cyanoacrylate Adhesive
SECTION 15 - REGULATORY INFORMATION
Safety, health and environmental regulations/ legislation specific for the substance or mixture
EU regulations: Regulation (EC) No 1907/2006
Regulation (EC) No 1272/2008
Authorizations and/or Restrictions on Use Authorizations: This product is not included on the Candidate List of Substances of Very High Concern for Authorization
Restrictions on use: The product is not subject to restrictions under Annex XVII of REACH Regulation.

Chemical safety assessment A chemical safety assessment has not been carried out.

SECTION 16 - OTHER INFORMATION

The labeling of the product is indicated in Section 2. The full text of all abbreviations indicated by codes in this safety data sheet are as follows:
Relevant R-phrases (Number and full text): R/36/37/38 Irritating to eyes, respiratory system and skin.
Relevant S-phrase (Number and full text): S2 Keep out of the reach of children.
S23 Do not breathe vapor.
S24/25 Avoid contact with skin and eyes.
S26 In case of contact eyes, rinse immediately with plenty of water and seek medical advice.
Relevant H-phrases (Number and full text): H315 Causes skin irritation.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.
Relevant P-phrases (Number and full text): P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and
easy to do. Continue rinsing.
P302+P350 If on skin: Wash with plenty of soap and water.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

This product is intended for use by skilled individuals at their own risk. The information contained herein is based on data considered accurate based on current state of
knowledge and experience. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof.

Revision Date: 9/1/25

HP ADHESIVES LIMITED
+91-22-68196300 [email protected] www.hpadhesives.com 11, Unique House, Chakala Rd,
Andheri (East), Mumbai - 400 099.