website:http://biz.lgservice.

com

COLOR TV
SERVICE MANUAL
CHASSIS : CW62B

MODEL: 21FB5RLX
MODEL: 21FB5RLX-ZV
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

VIDEO L AUDIO R
MENU OK VOL PR
ON/OFF

AV IN2

Dec.,2006
P/NO : MFL31616402 c Printed in China
 CONTENTS

Contents ....................................................................................................2

Safety Precautions....................................................................................3

Control Descriptions ................................................................................4

Specifications............................................................................................7

Adjustment Instructions...........................................................................8

SVC Remocon .........................................................................................13

Trouble Shooting ....................................................................................14

Printed circuit board...............................................................................17

Block Diagram.........................................................................................18

Exploded View.........................................................................................20

Exploded View Parts List .......................................................................21

Replacement Parts List ..........................................................................22

SVC. Sheet...................................................................................................

-2-
 SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed
An isolation Transformer should always be used during the metallic parts of the cabinet, such as antennas, terminals, etc., to
servicing of a receiver whose chassis is not isolated from the AC be sure the set is safe to operate without damage of electrical
power line. Use a transformer of adequate power rating as this shock.
protects the technician from accidents resulting in personal injury
from electrical shocks. Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
It will also protect the receiver and it's components from being electrical jumper across the two AC plug prongs. Place the AC
damaged by accidental shorts of the circuitry that may be switch in the on position, connect one lead of ohm-meter to the AC
inadvertently introduced during the service operation. plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
If any fuse (or Fusible Resistor) in this TV receiver is blown, jacks, etc.
replace it with the specified. If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When replacing a high wattage resistor (Oxide Metal Film Resistor, When the exposed metal has no return path to the chassis the
over 1W), keep the resistor 10mm away from PCB. reading must be infinite.
An other abnormality exists that must be corrected before the
Keep wires away from high voltage or high temperature parts. receiver is returned to the customer.

Due to high vacuum and large surface area of picture tube, Leakage Current Hot Check (See below Figure)
extreme care should be used in handling the Picture Tube. Do not Plug the AC cord directly into the AC outlet.
lift the Picture tube by it's Neck. Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
X-RAY Radiation between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Warning: Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
The source of X-RAY RADIATION in this TV receiver is the High Reverse plug the AC cord into the AC outlet and repeat AC voltage
Voltage Section and the Picture Tube. measurements for each exposed metallic part. Any voltage
For continued X-RAY RADIATION protection, the replacement measured must not exceed 0.75 volt RMS which is corresponds to
tube must be the same type tube as specified in the 0.5mA.
Replacement Parts List. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate high
impedance HV meter. Leakage Current Hot Check circuit
Adjust brightness, color, contrast controls to minimum. AC Volt-meter
Measure the high voltage.
The meter reading should indicate
23.5 ± 1.5KV: 14-19 inch, 26 ± 1.5KV: 19-21 inch,
29.0 ± 1.5KV: 25-29 inch, 30.0 ± 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and Good Earth Ground
correction is required to prevent the possibility of premature such as WATER PIPE,
component failure. To Instrument’s CONDUIT etc.
exposed 0.15uF
METALLIC PARTS

1.5 Kohm/10W

-3-
 DESCRIPTION OF CONTROLS

All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
1 10
Remote control handset
Before you use the remote control handset, please install the bat-
2 teries. See the next page.

1. POWER
switches the set on from standby or off to standby.
3 11
2. NUMBER BUTTONS
Switches the set on from standby or directly select a number.
PR
3. MENU
VOL VOL selects a menu.
4 OK
4. D / E (Programme Up/Down)
13 PR selects a programme or a menu item.
14
switches the set on from standby.
scans programmes automatically.
6 F / G (Volume Up/Down)
5
adjusts the volume.
adjusts menu settings.
12 OK
7 accepts your selection or displays the current mode.

5. TELETEXT BUTTONS (option)

8 9 These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
(With TELETEXT / PIP) 6. SLEEP
sets the sleep timer.

7. PIP BUTTONS (option)

PIP
switches the sub picture on or off.
PR PR +/-
selects a programme for the sub picture.
VOL VOL SWAP
OK
alternates between main and sub picture.
Q.VIEW LIST INPUT
PR selects the input mode for the sub picture.
SIZE
adjusts the sub picture size.
5 STILL
freezes motion of the sub picture.
UPDATE/ HOLD/ POSITION
relocates the sub picture in clockwise direction.

(With TELETEXT / Without PIP)

-4-
8. FAVOURITE
selects a favorite programme.

9. EYE/ (option)
*
switches the eye function on or off.
1 10

10. MUTE
switches the sound on or off. 2

11. TV/AV
selects TV or AV mode.
switches the set on from standby. 3 11
exits the Teletext mode(option).

12. I/II/ PR
* the language during dual language broadcast.
selects
selects the sound output (option). 4 VOL OK VOL

Q.VIEW LIST
13. Q.VIEW (or SWAP) PR
returns to the previously viewed programme. 13 14
9
14. LIST (or INPUT) 6 8
displays the programme table.
12

* : No function
COLOURED BUTTONS : These buttons are used for teletext (only (Without TELETEXT / PIP)
TELETEXT models) or programme edit.

PR

VOL OK VOL

PR

(With PIP / Without TELETEXT)

-5-
21FB5 series 1. MAIN POWER (ON/OFF)
VIDEO L AUDIO R
switches the set on or off.
MENU OK VOL PR
ON/OFF

AV IN2

2. POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby
1 2 3 4 5 6 7
mode.
dims when the set is switched on.

3. REMOTE CONTROL SENSOR

Note : Only use the supplied remote control
handset. (When you use others, they won’t be
able to function.)

4. MENU (option)
selects a menu.

5. OK (option)
accepts your selection or displays the current
mode.
F / G (Volume Up/Down) (option)
adjusts the volume.
Side panel adjusts menu settings.
D / E (Programme Up/Down) (option)
selects a programme or a menu item.
switches the set on from standby.

6. AUDIO (or AUDIO-L/R)/VIDEO IN SOCKETS

(AV IN2) (option)
6
Connect the audio/video out sockets of external
6
equipment to these sockets.

7. EYE (option)
adjusts picture according to the surrounding
conditions.

Note : Shown is a simplified representation of front

or side panel. What is shown here may be
somewhat different from your set or can not be
supplied on your area.
6 6 6

-6-
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.

O2@@6Khe
W2@@@@@@6Xh
7@@@@@@@@1h

Scope
?J@@@@@@@@@@L?g
?7@@@@@@@@@@1?g
?@@@@@@@@@@@@?g
?@@@@@@@@@@@@?g
?3@@@@@@@@@@5?g
?N@@@@@@@@@@H?g
3@@@@@@@@5h
V4@@@@@@0Yh
I4@@0Mhe
O2@@6Khe
W2@@@@@@6Xh
7@@@@@@@@1h
?J@@@@@@@@@@L?g
?7@@@@@@@@@@1?g
?@@@@@@@@@@@@?g
?@@@@@@@@@@@@?g
?3@@@@@@@@@@5?g
?N@@@@@@@@@@H?g
3@@@@@@@@5h
V4@@@@@@0Yh
I4@@0Mhe
Test Condition
This specification can be applied to all the television related to 1) Temperature : 20 ± 5°C(CST : 40 ± 5°C)
CW62B Chassis. 2) Relative Humidity : 65 ± 10%
3) Power voltage : AC110-240V~, 50/60Hz(Middle East/Africa)
AC 230V~50/60Hz (EU/CIS)
O2@@6Khe
W2@@@@@@6Xh
7@@@@@@@@1h

Test and Inspection Method

?J@@@@@@@@@@L?g
?7@@@@@@@@@@1?g
?@@@@@@@@@@@@?g
?@@@@@@@@@@@@?g
?3@@@@@@@@@@5?g
?N@@@@@@@@@@H?g
3@@@@@@@@5h
V4@@@@@@0Yh
I4@@0Mhe 4) Follow each drawing or spec for spec and performance of
1) performance : Follow the Standard of LG TV test parts,based upon P/N of B.O.M
2) Standards of Etc. requirement 5) Warm up TV set for more than 20min. before the
- Safety: IEC60065 measurement.
- EMC: EN55020,EN55013

O2@@6Khe
W2@@@@@@6Xh
7@@@@@@@@1h

General Specification
?J@@@@@@@@@@L?g
?7@@@@@@@@@@1?g
?@@@@@@@@@@@@?g
?@@@@@@@@@@@@?g
?3@@@@@@@@@@5?g
?N@@@@@@@@@@H?g
3@@@@@@@@5h
V4@@@@@@0Yh
I4@@0Mhe

No Item Specification Remark

1 Receiving System PAL,SECAM BG EU/ Non EU
PAL/SECAM DK
PAL-I/I
NTSC M
NTSC 4.43(AV)
SECAM-L/L’ OPTION
NTSC M/ PAL M/N
2 Available Channel VHF : E2 ~ E12 Non EU/ EU
UHF : E21 ~ E69
CATV : S1 ~ S20
HYPER : S21 ~ S41
VHF : 02 ~ 13 NTSC-M
UHF : 14 ~ 69
CATV : 02 ~ 71
3 Input Voltage AC 110-240V, 50/60Hz Non EU
AC 230V, 50/60Hz EU
4 Market EU,CIS, China, Asia, Africa,Middle East
5 Screen Size Flat 21”
6 Tuning System FVS 100Program PAL 200 PR(W/O TXT)
7 Operating Environment 1) Temp : 0 ~ 45 deg
2) Humidity : below 85%
8 Storage Environment 1) Temp : -20 ~ 60 deg
2) Humidity : below 85%

-7-
 ADJUSTMENT INSTRUCTIONS
1. Application Object 4. Purity & Convergence adjustment
These instructions are applied to all of the color TV, CW62B.
Adjustment should be operated when using the CPT(without
ITC from CPT manufacturing place)
2. Notes This adjustment must be done in the order of the following
(1) Because this is not a hot chassis, it is not necessary to use flowchart.
an isolation transformer. However, the use of isolation
CPT Assembling As preparatory operations before
transformer will help protect test instrument.
assembling CPT, wind cotton Tape for
(2) Adjustment must be done in the correct order.But the
protecting to CPT NECK and DY, CPT
adjustment can be changed by consideration of mass
connection parts. At this moment, end
production.
of tape should be over-lapped and
(3) The adjustment must be performed in the circumstance of
wound in direct route to the NECK.
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation. Fix the Magnet to the position as
Assembling DY to
(4) The input AC voltage of the receiver must keep rating shown picture below. Be careful not to
CPT
voltage in adjusting. make CPT neck shadow while
(5) The receiver must be operated for about 20 minutes prior HEAT RUN adjusting DY.
to the adjustment.
(6) Signal: Received, the standard color signal.(65dB±1dB uV) Degaussing
Convergence Magnet 6Pole 4 2

LG standard signal means the digital pattern

(PAL_EU 05CH,NTSC_US 13CH). STC Pre-Adjustment
¢‚
¢‚
15 ~ 20mm
PURITY Adjustment
3. Focus adjustment
DY Fixing Let the screen Standard condition.
(1) Receive the Cross-Hatch Pattern(Fig 1). Operate Heat-Run at least 15
(2) Set the picture condition on “DYNAMIC(CLEAR)” mode. minutes.
SCREEN Voltage adj.
(3) Adjust the Focus volume of FBT,made the focus of the 1/4
part vertical line is best. Torque is to be 9-11 kg f.cm when
W/B Fixing fixing DY.
A B
FOCUS not yet ADJ.

STC not yet ADJ.

DYC not yet ADJ.

4.1. Color purity adjustment

(1) It makes CPT or CABINET enough to demagnetization.
(2) Receive the signal of red raster.
(3) Unfasten DY and push DY to FUNNEL direction.
(4) Make R-Land be centered as cross Purity Magnet. That
<Fig. 1> Cross-Hatch Pattern (NTSC : US 09CH, PAL : E-7CH) time, 4 & 6 pole magnet should keep free gauss status.
(5) Make uniform RED Raster as moving DY,Check there is
purity problem or not on R/G/B,white Raster. Then fix screw
of DY.
(At this time, be careful about inclination and DY should be
fixed keeping horizontality.)
(6) Check the TV set in direction of EAST, WEST, SOUTH,
NORTH. Adjust with supporing MAGNET when adjustment
is not operated.

4.2. Convergence adjustment

These adjustments should be operaed at the best condition of
focus after finished purity adjustment.

(1) Receive the signal of cross hatch that BACK RASTER is

black.
(2) Adjust brightness so that there are 9 ~12 dots.

-8-
 (3) Widen two tabs of 4pole Magnet with equal angles and <Table 3> White Balance Initial Data
accord red,blue vertical lines at the center of screen. 1. IC PARAMETER
(4) With keeping angle of "c.clause",rotate tab and accord Name Maker Algorithm
red/blue,green vertical lines at the center of screen.
(5) Widen two tabs of 6pole Magnet with equal angles and VCD IC
accord red,bllue vertical lines at the center of screen. 0 0 0 0
EP_ROM
(6) With keeping angle of "e.clause",repeat the adjustment
from c to e keeping in mind the movement of
red,blue,green when the horizontal lines are twisted. 2. White balance IIC Parameter(Address)
(7) Move the DY up,down,left,right and make the convergence Program Win31_wb TWB Win31_wb TWB Speed Delay
to be optimal condition and stick rubber wedge to CPT so
Vcd Slave 8A Eeprom_Slave A0 1 30
that the DY not to move.

B(R)_Amp B(R)_Cut G_Amp G_Cut

5. Screen voltage adjustment Program Win31_wb TWB Win31_wb TWB Win31_wb TWB Win31_wb TWB

Sub Add 20 17 21 18
SCREEN manual adjust method(Used the remote controller)
(1) RF Mode,input the PAL or SECAM(NTSC)singal,every Start Bit 5 5 5 5
channel is OK. Stop Bit 0 0 0 0
(2) First LINE SVC MODE(IN-START KEY) and push the ADJ
Offset 0 0 0 0
KEY change to the SCREEN adjustment MODE.
(3) Adjust the SCREEN VOL of the FBT,then TV picture will Polarity 1 1 0 0
be have a horizontal line,manual adjust the FBT SCREEN EP_Rom_S 36 33 37 34
VOL,when the horizontal line just disappear is OK
(Press the TV/AV button to exit SVC mode) Speed/ Plus 2 2 2 2

6. White balance adjustment

7. Deflection setting Data Adjustment
(1) Receive 100% white pattern.
(2) From the initial data,adjust BLO-R(R CUT),BLO-G(G CUT) 7.1 Adjustment preparation
keep X,Y coordinate settle for the below list,adjust the (1) TV set to receive an Digital pattern(PAL:E5ch.,NTSC: US-
LOW LIGHT(4.5FL). 12).
(3) From the initial data:BG(B-DRIVE) is 32,adjust RG(R- (2) Deflection data setting used remote.
DRIVE),GG(G-DRIVE) keep X,Y coordinate settle for the (3) press the LINE SVC MODE(IN-START KEY) into
below list,adjust the HIGH LIGHT(35FL). SERVICE MENU,Choice SERVICE2 to adjustment mode.
?
?
?
?
?
?
(4) Press CH+,CH- KEY chooice adjust item.
?
?
?

HIGH LIGHT,LOW LIGHT adjust reiterative. (5) Press VOL+,VOL - KEY increase or decrease DATA.
?
?
?W&?he?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he?
?
?
?
?
?
?
?
?
?
?
?
?
?
?

W/B adjust initial data maybe difference by different

?
?W&?he?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he?
?
?
?
?
?
?
?

model,so please refer to the model adjust TABLE. 7.2 Adjustment

(1) First,adjust deflection at 50Hz,of PAL signal.
<Table 1> White Balance Coordinate(By market) then,adjust deflection at 60Hz, of NTSC signal.
Item EU N-EU (2) Korea Model only used the N60Hz,adjustment .
Adjust vertical inclination of screen.
X 288 268
(3) Central or South America Model first N60Hz adjustment
Y 295 273 and then N50(PAL-N) adjustment.
Chroma 9000 13000 (4) when finish the adjustment and press"ENTER" KEY,save
data andexit adjustment Mode.
<Table 2> White Balance Initial Data ?
?
?
?
?
?
?
?
?

Deflection adjustment small item

?
?
?W&?he?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he? ?
?
?
?
?
?
?

DATA
Menu Range (1) V SLOPE
PAL NTSC
The cutting part(below) of picture transfer to Blanking.
LOW LIGHT BLO-R(R CUT) 0 ~ 63 32 32 Adjust the geometric vertical center of the CPT is in accord
BLO-G(G CUT) 0 ~ 63 32 32 lower blanking.
BLO-B(B CUT) 0 ~ 63 32 32
(2) VS (Vertical Shift)
HIGH LIGHT RG(R DRIVE) 0 ~ 63 32 32 Adjust so that the horizontal center line of a digital circle
GG(G DRIVE) 0 ~ 63 32 32 pattern is in accord with geometric horizontal center of the
CPT.
BG (B DRIVE) 0 ~ 63 32 32

-9-
(3) VL (Vertical Linearity) (11) H ANGLE
Adjust so that the boundary line between upper and lower Adjust the vertical slope
half is in accord with geometric horizontal center of the
CPT(PAL : E5ch., NTSC : US-13.). (12) S CORRECT (S CORRECTION)
Adjust the receive Patter, keep the lattice's range
(4) VA (Vertical Amplitude) same(Top/Center/Bottom)
?
?
?
?
?
?
?
?
?
?

Adjust so that the circle of a digital circle pattern may be This decided by DY data,so according to the CPT's Default
?W&?he? ?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he? ?
?
?
?
?
?
?

located within the effective screen of the CPT.

?
?
?
?
?
?
?
?
data(Initial data) Setting.
?
?

NTSC signal : Adjust NTSC 13CH circle as an inscribed

?W&?he? ?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he? ?
?
?
?
?
?
?

circle of vertical outer boundary of the effective screen of (13) V SCROLL

the CPT. Adjust the center vertical line of the geometrical with the
CPT center vertical line same.

Adjust Point (14) V ZOOM (fixed) : VERTICAL ZOOM.

(15) WBR (fixed) : Timing of wide Blanking

<Fig. 2 >
(16) WBF (fixed) : Timing of wide Blanking
(5) HS (Horizontal Shift)
Adjust so that the vertical center line of a digital circle (17) V SYNSLI (fixed) : Vertical slicing level
pattern is in accord with geometric vertical center of the
CPT ?@@?
?@@? (18) OVRVOLIN (fixed) : Over voltage input mode

(6) EW (Horizontal Width) (19)V GUARD (fixed) : Vertical guard mode

Adjust to that a digital circle pattern looks like exact
circle.(PAL:0~25%,NTSC: 2.5~3.0)
Factual picture size Factual picture size 8. initial data for deflection
<Table 4> Initial data for deflection by model (SERVICE 2)-PAL

21”S-SLIM 21”FLAT Adjust

Item Description
50Hz 60Hz 50Hz 60Hz or not

V SLOPE Vertical slope 15 16 24 18 YES

V SHIFT Vertical shift 48 45 48 40 YES
V LINEAR Vertical linearity 43 44 43 33 YES
V AMPLIT Vertical amplitude 29 31 19 44 YES
PAL Digital Pattern(EU05CH) NTSC Digital Pattern(US13CH)
H-SHIFT Horizontal shift 30 35 34 31 YES
<Fig. 3> Cross-Hatch Pattern
EW WIDTH EW width 46 52 46 35 YES
(7) EP (East-west Parabolar) EW PARAB Parabola adj 25 36 25 24 YES
Adjust so that middle portion of the outermost left and right EW TRAPE Trapezoid adj 19 23 19 28 YES
vertical line looks like parallel with vertical lines of the CPT. EW UPCOR Upper corner adj 35 50 35 44 YES
EW LOCOR Lower corner adj 46 53 46 48 YES
(8) ET (East-west Trapezium)
H BOW Bow 35 34 35 35 YES
Adjust to make the length of top horizontal line same with it
of the bottom horizontal line. H PARALL Horizontal parallelogram 26 37 32 28 YES
SCORRECT S correction 36 35 36 30 NO
(9) EW UPCOR & EW LOCOR V SCROLL Vertical scroll 27 21 21 21 Adjust
Adjust until symmetrize upper&lower coner of the screen. if need
V ZOOM Vertical zoom 25 25 25 25 NO
UPCOR WBR Timing of wide Blanking 2 2 2 2 NO
WBF Timing of Wide Blanking 2 2 2 2 NO
V SYNSLI Vertical slicing level 0 0 0 0 NO
EW PARAB OVRVOLIN Over voltage input mode 0 0 0 0 NO
V GUARD Vertical guard mode 1 0 1 1 NO
LOCOR
?
?
?
?
?
?
?
?
?

After PAL50Hz adjustment for Pal mode,NTSC60Hz apply

?
?
?
?
O2@6K?h?
W2@@@@@6X?g?
7@@@@@@@1?g?
?J@@@@@@@@@Lg?
?7@@@@@@@@@1g?
?@@@@@@@@@@@g?
?3@@@@@@@@@5g?
?N@@@@@@@@@Hg?
3@@@@@@@5?g?
V4@@@@@0Y?g?
I4@0M?h? ?
?
?
?
?
?
?
?
?

deflection redress data,but you need confirm the

<Fig. 4> Cross-Hatch Pattern(NTSC:US 9CH,PAL:E-7CH) adjustment condition in NTSC System again,if it is no
good,you need readjust it in NTSC mode.
(10) BOW
Adjust the left and right crooked line on upper and lower
side.

- 10 -
9. SVC DEFAULT DATA [Table 7] SERVICE 4
(manage DATA by EEPROM MASTER) ITEM Description N-EU EU Refer
WS WHITE STRETCH 1 1
[Table 5] SERVICE 1
BKS BLACK STRETCH 1 1
CW62B BSD BLACK STRATCH DEPTH 0 0
ITEM DESCRIPTION
N-EU EU DSK DYNAMIC SKIN CONTROL 1 1
AGC ACG take over 25 25 COR VIDEO DEPENDENT CORING 2 2

RG Red Gain 32 32 PF PEAKING FREQUENCY DELAY 2 0

RPO RATION POSITIVE/ 2 2
GG Green Gain 32 32
NEGATIVE PEAKS
BG Blue Gain 32 32
RPA RATION PRE/AFTER SHOOT 2 2
BLO-R Black level offset Red 32 32
PWLDAC PEAK WHITE LIMITER DAC 8 8
BLO-G Black level offset Green 32 32 IFOFF IF DEMODULATIOR 37 37
CDL Cathode Drive Level 8 8 CHSE CHROMA SENSITIVITY 1 1

L-DLY PA Luminance delay time for PAL 2 2 ACL AUTO COLOR LIMITING 1 1
CLPDEL50 Clamping delay 50 18 -
L-DLY SE Luminance delay time for secam 13 13
CLPDEL60 Clamping delay 60 18 -
RGB-BRI OSD/TEXT BRIGHTNESS 27 27
CLPLEN Clamping Pulse Length 3 - PIP data
CLMPID Clamping Duration 3 -
[Table 6] SERVICE 3
PIP H PIP H position 10 -
CW62B
ITEM DESCRIPTION Remark
EU NEU
[Table 8] option 1,2,3,4
OVMADAPT OVER MODULATION ADAPT 1 1
OVMTHR OVER MODULATION 1 1 ITEM Description
THRESHOLD OPTION1 INCH Flat/slim/ultra/Conventional
ADC LEV ADC LEVEL(-16~15)-ADCLEV 16 16 SYSTEM BG/DK/I/M - no EU, BG/DK/I/L - EU
DEC LEV DEC LEVEL(-16~15)-DECLEV 18 18 FM pre-scaler 200PR W/O TXT=>200PR,W/TXT=>100PR
MONO LEV MONO LEVEL 18 18 (stereo L/R) TOP FLOF - other Nation
(-16~-15)MONLEV FM pre-scaler TOP - Germany, Swiss, Austria, Italy
NICAMLEV NICAM LEVEL(-16~15)-NICEV 22 22 (Mono) ACMS Off - Australia only/ On - other Area
FILTBW FILTER BANDWIDTH 0 0 CH-AU China & Australia Frequency table
BAMA FC BAMA FC 60 60 NICAM pre-scaler BOOSTER Booster off/on
AUX3 VOL AUX3 VOL 84 89 OPTION2 SOUND RF stereo / AV stereo / Mono Dual
(SCART1 RF SOUND OUT) PIP PIP option
FMWINDOW FM WINDOW FILTER(FMWS) 1 1 Scart pre-scaler RESERVED Reserved option
BOOSTVAL BOOSTER 0 0 VOL CURVE Eu low curve/ Non EU high Curve
MAX VOL MAX VOLUME 100 100 A2 STEREO Nicam check & FM stereo/ Dual act or not
DCXO VAL DCXO 50 50 I/II SAVE Dual soung setting save or not
DCXOA DCXO 0 0 HIDEVIAT Sound high deviation apply
TEXT-V TEXT V POSITION 40 40 OPTION3 SCART countermeasure or not SCART option
TEXT-H TEXT H POSITION 4 4 DVD DVD option
XWAVE FM TX option
EYE EYE option
4KEY 4 Key option
TILT TILT option
DEGAUSS Degaussing option
OPTION4 OSD LANG Refer to the next page(table.8)
TXT LANG Refer to the next page(table.8)
OPTION5 REMOCON Large type Remocon / Small type Remocon
HOTEL HOTEL option
TURBOSCH Turbo search
TURBOP/S Turbo picture/ sound
BLUEBACK Blue back option
TEXT Teletext option

- 11 -
 ?W&?he?
W&@Lhe?
?W&@@)X?h?
W&@@@@)Xh?
?W&@@@@@@)X?g?
W&@@@@@@@@)Xg?
?
?
?
?
?
?
?
?
?
?
?

OPTION DATA BOM example

?
?

?O&@@@@@@@@@@)K?f?
'@@@@@@@@@@@@@@(f?
V'@@@@@@@@@@@@(Yf?
?V'@@@@@@@@@@(Y?f?
V'@@@@@@@@(Yg?
?V'@@@@@@(Y?g?
V'@@@@(Yh?
?V'@@(Y?h?
V'@Hhe?
<Tabel 11> PSM MODE DATA SETTING (PAL)
?V'?he?
?

Picture mode DATA SETTING

?
?
?

LEVEL PART NO. SPECIFICATION DESCRIPTION

PSM Dynamic Standard Mild Game
1. 3141VM382A MAIN CHASSIS ASSY [112.68.164.32.8] CONTRAST 100 90 60 50
BRIGHT 60 55 55 55
COLOR 60 55 55 60
<Table 9> OSD & TEXT LANGUAGES
SHARPNESS 60 60 50 50
1. East EU Area OSD lang 0 ENGLISH
1 East EU
<Table 12> APC MODE DATA SETTING (NTSC)
2 Russian
Picture mode DATA SETTING
TXT LANG 0 EU WEST
1 EU EAST PSM Clear Optimum Soft
2 Russian W CONTRAST 100 70 55
3 Russian E BRIGHT 55 45 45
4 UKRAINIAN COLOR 50 45 40
5 BYELORUSSI SHARPNESS 50 40 30
6 GREEK
2. Arab - Farsi OSD lang 0 English
1 Arabic
2 Farsi 11. OPTION Adjustment (PAL)
3 Arab all
TXT LANG 0 EU West
1 EU East 1) OPTION Adjustment need by Model name, used the remote
controller press the IN-START KEY and start adjust.
2 Arabic
Choice OPTION 1,2,3,4,5 adjust one by one.
3 Farsi 2) OPTION1 ???(0~255), OPTION2 ???(0~255), OPTION3
3. ASIA OSD lang ???(0~250), OPTION4 ???(0~337), OPTION5 ???(0~252)
TXT LANG
4. West EU OSD lang
TXT LANG 12. SOUND PRE-SCALER
This SVC data settin by every buyer's spec., so can't change it.

10. IN-STOP Condition

?
?
?
?
?
?
?
?

Audio Out Level SPEC

?
?
?
?W&?he?
?'6Xe?*@?eW2(?f?
?V')X??V'??W&(Y?f?
V')XfW&(Yg?
?V')X??W&(Y?g?
V')KO&(Yh?
W-X??V'@@(Y??W-Xf?
&@)?e?@@?e?&@)f?
?W&@@)X?h?
W&(MI')Xh?
?W&(Y??V')X?g?
W&(YfV')Xg?
?W&(Y??W&??V')X?f?
?&0Ye?*@?eV4)?f?
?V'?he?
?
?
?
?
?
? ?
? ?
?
?
?
?
?
?
?
?

PAL B/G, D/K,I : 500m Vrms at 54% modulation ratio.

?
W&he?
?W&@L?h?
W&@@)Xh?
?W&@@@@)X?g?
W&@@@@@@)Xg?
?W&@@@@@@@@)X?f?
W&@@@@@@@@@@)Kf?
7@@@@@@@@@@@@@(?e?
3@@@@@@@@@@@@(Y?e?
V'@@@@@@@@@@(Yf?
?V'@@@@@@@@(Y?f?
V'@@@@@@(Yg?
?V'@@@@(Y?g?
V'@@(Yh?
?V'@H?h?
V'he? ?
?
?
?

<Table 10>
?
?
?
?
?
?
?
?
?
?
?

SECAM B/G, D/K, L/L : 500m Vrms at 54% modulation ratio.

?
?
W&he?
?W&@L?h?
W&@@)Xh?
?W&@@@@)X?g?
W&@@@@@@)Xg?
?W&@@@@@@@@)X?f?
W&@@@@@@@@@@)Kf?
7@@@@@@@@@@@@@(?e?
3@@@@@@@@@@@@(Y?e?
V'@@@@@@@@@@(Yf?
?V'@@@@@@@@(Y?f?
V'@@@@@@(Yg?
?V'@@@@(Y?g?
V'@@(Yh?
?V'@H?h?
V'he? ?
?
?
?
?
?
?
?
?
?
?
?
?
?

NTSC-M : 500m Vrms at 100% modulation ratio.

W&he?
?W&@L?h?
W&@@)Xh?
?W&@@@@)X?g?
W&@@@@@@)Xg?
?W&@@@@@@@@)X?f?
W&@@@@@@@@@@)Kf?
7@@@@@@@@@@@@@(?e?
3@@@@@@@@@@@@(Y?e?
V'@@@@@@@@@@(Yf?
?V'@@@@@@@@(Y?f?

ITEM Condition Mark

V'@@@@@@(Yg?

No.
?V'@@@@(Y?g?
V'@@(Yh?
?V'@H?h?
V'he? ?
?
?
?
?
?

1 Power OFF
2 Input TV
3 MEMORY CHANNEL CH.MEMORY
4 SOUND 30STEPS
5 MUTE OFF
6 PSM DYNAMIC
7 XD ON
8 SSM FLAT
9 TURBO SOUND FLAT
10 AVL OFF
11 BALANCE 0
12 ON/OFF TIME OFF
13 AUTO SLEEP OFF
14 CHILD LOCK OFF
15 DEGAUSS OFF
16 EYE OFF OPTION
17 TILT 0 OPTION
18 BLUE BACK OFF OPTION

- 12 -
SVC REMOCON

- 13 -
 TROUBLE SHOOTING

1. RF-STEREO MODEL
1) PICTURE OK / NO SOUND

Selected correct system in menu

OK
NO
Check the waveform IF 1 of TU101 Check/ Replace TU101 or Input signal

OK
NO NO
Check the voltage at pin 3, 9, 16, 43,
Check the waveform at pin 4, 5 of IC11 Check/ Replace IC11
86, 88, 90 of UOCIII

OK

NO
Check the waveform at pin 4, 12 of Check the voltage at pin 57, 58 of
IC601 UOCIII

OK
NO
Check the waveform at pin 6 of IC601 Check/ Replace Q603

OK

NO
Check the waveform at pin 1, 2, 14, 15
Check/ Replace IC601
of IC601

OK

NO
Check the waveform at pin 3, 13 of
Check/ Replace R823, D826
IC601

2) No Raster / Sound OK(1/2)

Check the Heater voltage of

CPT(6~6.4 Vrms)

Check HV, Screen voltage of CPT Check R, G, B out of CPT board Check the Heater pulse of FBT T402

Check IC901,
Check FBT T402 Check 190V line of CPT Board & Check RF901, P903C, Check FBT T402
P402A
if no problem check and Replace P903B, FR401

- 14 -
3) No Raster (2/2)

Check the B+ at D829

cathode
Normal Abnormal

OPEN
NO Check Fuse of AC line
Is the voltage each
pin voltage of IC11

OK Check/ Replace Fuse

Check the in/out of

regulator(IC822,
Check pin 73 of Check the voltage of NO
IC823, IC824)
IC11(H_Out) C832

Check/ Replace
IC11 Check/ Replace DB801

Check Q402
collector waveform Check the voltage NO
pin4 of IC810
Check/ Replace
Q402
Check/ Replace Fuse and IC810
Check T401 & each
pin voltage
Check/ Replace
IC810, IC802, Q830
Check/ Replace
T401

Check Q401collect NO
Check Fuse and Diode of secondary
waveform
Load of SMPS trans(T802)

Check/ Replace
Q401
OK
Check & Replace Check/ Replace IC11
T402

- 15 -
4) No Picture/ No Sound

Is any OSD displayed?

NO

OK

OK
Check IC11 pin 83, Check receiving system in MENU OK
84, 85 (R, G, B out) & execute Auto - Program

Does the auto - Program

operate properly
NO

OK

Store on manual -program MENU

NO NO
Check the waveform Check IC11 pin 83, Check SMPS Trans Go to No sound/
pin73(H-out) 84, 85 (R, G, B out) Secondary Voltage picture OK

OK

Check pin3 Reset

Voltage

OK
NO
Check pin8, 12 SCL, Check IC12(EEPROM)
SDA & SCL, SDA, Line
OK

OK

Replace IC11

P904A (R, G, B out P904A (R, G, B out

of IC501) of IC11)

- 16 -
 PRINTED CIRCUIT BOARD
MAIN

- 17 -
BLOCK DIAGRAM

- 18 -
MEMO

- 19 -
 EXPLODED VIEW

913
943
170 150 400

112

174

120
121

520
300

310

330 320

- 20 -
 The components identified by mark is
EXPLODED VIEW PARTS LIST critical for safety.
Replace only with part number specified.

LOCA. No. PART No. DESCRIPTIONS

112 EAK30526501 CPT,ITC A51QDJ420X75 21INCH FLAT V(-0.36) ~S(-0.5) 4/3 60HZ ITC

120 EAB30823501 Speaker,Fullrange JF 8 FERRITE 10W 8OHM 84DB 130HZ 126 X 57 X 46 LUG

121 4810V00088B Bracket MOLD PP SPEAKER CE-29K30 NON PP NONE

150 6140VC2007E Coil,Degaussing RT-21FB57V 11OHM AL 44T 0.6mM SQUARE 21INCH

170 170-A01N Drawing,Assembly CPT EARTH UL1015 AWG22 21INCH NORMAL

174 6410VEH001E Power Cord YP-204 ZH.B 2.41M 300MM 250V 2.5A H03VVH2-F 2X0.75MM2

300 3091V00495L Cover Assembly 21FB5RLX-ZV CW62B 21” MA TOOL W/O EARPHONE”

310 5020V00763C Button MOLD ABS CONTROL RZ-21FB55RX ABS, HF-380 6KEY

320 320-062E Spring CUTTING STSC304 COIL STEEL

330 5020V00764B Button MOLD ABS POWER RZ-21FB55RX ABS, HF-380 1KEY LGEMA

400 3809V00342E Cover Assembly RZ-21FB55RX 1PHONE SY-LGEMA 049B(MA LOCAL)

520 EBR33392702 PCB Assembly,Main MAIN M.I CW62B 21FB5RLX-ZV QUHLLCP SY-MA SKD

EBR33392705 PCB Assembly,Main MAIN M.I CW62B 21FB5RLX-ZV QUPLLCP SY-MA SKD

EBR33392706 PCB Assembly,Main MAIN M.I CW62B 21FB5RLX-ZV QUZLLCP SY-MA SKD

EBR33392707 PCB Assembly,Main MAIN M.I CW62B 21FB5RLX-ZV QURLLCP SY-MA SKD

EBR33392743 PCB Assembly,Main M.I CW62B 21FB5RLX-ZV QUHLCCK SY-MA SKD

EBR33392737 PCB Assembly,Main M.I CW62B 21FB5RLX-ZV QEULCCK SY-MA SKD

913 FAB30021402 Screw Assembly FAB30021402 TAPTITE P TYPE D5.0 L35.0 SAW TOOTHED

943 FAB30006309 Screw,Taptite 1SZZ9PB012A TH + P 4MM 16MM MSWR10 FZB

- 21 -
 REPLACEMENT PARTS LIST
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the characters at 2nd and 3rd CQ : Polyester RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

D818 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D

IC
D820 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
IC12 0IAL241610B AT24C16A-10PU-2.7 16KBIT 2KX8BIT 2.7 D823 EAH30560501 SFAF504G 200V 975MV 10UA 125A 35NSEC
IC301 0IPMGPH002A TDA4863A 9.0VTO30.0V - 3.2W - DBS ST D826 0DRTW00141A SFAF504G 200V 975MV 10UA 125A 35NSEC
IC601 0ILNR00189A TDA7297SA 6TO18V 0 0.10% 15W 30W 56D D828 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
IC802 0ILI817000G LTV-817M-VB 6V 35V 35V 50MA 100NA 60 D829 0DRDC00014F RU3AM 600V 1100MV 10UA 50A 90NSEC DO
IC810 0IPMGSK016A STR-W6753 16.3TO19.9V 8.8TO10.6V SWI D844 0DRDC00014J EU1Z 200V 2.5V 10UA 15A 50NSEC DO41
IC823 0IMCRAU004A S1117-33PIC 4.8TO12V 3.3V 2W TO220 S D845 0DRDC00014Q EU1ZS 200V 2.5V 10UA 15A 120NSEC DO4
IC824 0IMCRKE020A KIA78S06P 8.1TO21V 6V 600MW TO92 ST D846 0DRDC00014J EU1Z 200V 2.5V 10UA 15A 50NSEC DO41
IC826 0IMCRKE018A KIA78R05API 6TO12V 5V 1.5W TO220IS S D847 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
IC901 0IPRP00747A TDA6107AJF 180TO210V 6mA 5.5M SIP ST D901 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
Q602 0IFA754207A KA75420ZTA(KA7542ZTA) 0.3TO15V 4.2V D902 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
Q830 0IMCRFA007A KA431AZ 2.47TO2.52V 36V 770MW TO92 T D903 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D
SW SAA30112702 3.00 5276 EUROPE FLASH ROM CW62B EAS D904 0DRDC00014E 1N4004A 400V 1100MV 5UA 30A - DO41 T
DB801 0DRTW00071A TS4B05G-1021 600V 1V 5UA 120A TS4B S
TRANSISTOR
ZD101 0DZ330009DG GDZJ33B 33V 30.32TO31.88V 65OHM 500M
Q105 0TR102009AB KRC102M(KRC1202) NPN 30V - 50V 100MA ZD102 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q11 0TR198009BA 2SA1980Y PNP -5V -50V -50V -0.15A -0 ZD401 0DZ510009BF GDZ5.1B 5.1V 4.94TO5.2V 20OHM 500MW
Q201 0TR198009BA 2SA1980Y PNP -5V -50V -50V -0.15A -0 ZD501 0DZ510009AK GDZJ5.1B 5.1V 4.94TO5.2V 80OHM 500MW
Q301 0TR198009BA 2SA1980Y PNP -5V -50V -50V -0.15A -0 ZD502 0DZ820009BF GDZJ8.2B 8.2V 7.78TO8.19V 20OHM 500M
Q401 0TRSA10004A TT2170LS-YB11 NPN 5V 1.5KV 800V 5A 1 ZD503 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q402 0TR233109AA KSC2331Y NPN 8V 80V 60V 700MA 100NA ZD504 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q502 0TR198009BA 2SA1980Y PNP -5V -50V -50V -0.15A -0 ZD505 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q503 0TR319809AA KTC3198(KTC1815) NPN 5V 60V 50V 150M ZD506 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q504 0TR319809AA KTC3198(KTC1815) NPN 5V 60V 50V 150M ZD507 0DZ910009BD GDZJ9.1B . 9.1V 8.57TO9.01V 25OHM 50
Q505 0TR127009AA KTA1270-Y(KTA562TM) PNP -5V -35V -30 ZD601 0DZ820009BF GDZJ8.2B 8.2V 7.78TO8.19V 20OHM 500M
Q506 0TR127009AA KTA1270-Y(KTA562TM) PNP -5V -35V -30 ZD827 0DZ750009BE GDZJ7.5B 7.5V 7.07TO7.45V 20OHM 500M
Q603 0TR534309AA 2SC5343Y NPN 5V 60V 50V 150MA 100NA ZD841 0DZ620009AH MTZJ6.2A 6.2V 5.78TO6.09V 30OHM 500M
Q803 0TR102009AB KRC102M(KRC1202) NPN 30V - 50V 100MA ZD910 0DZ510009BF GDZ5.1B 5.1V 4.94TO5.2V 20OHM 500MW
Q804 0TR534309AA 2SC5343Y NPN 5V 60V 50V 150MA 100NA ZD911 0DZ510009BF GDZ5.1B 5.1V 4.94TO5.2V 20OHM 500MW
Q805 0TR102009AB KRC102M(KRC1202) NPN 30V - 50V 100MA ZD912 0DZ510009BF GDZ5.1B 5.1V 4.94TO5.2V 20OHM 500MW
Q806 0TR127409AB KTA1274-Y PNP -5V -80V -80V -0.4A -0
Q809 0TR319809AA KTC3198(KTC1815) NPN 5V 60V 50V 150M
CAPACITOR
Q810 0TR319809AA KTC3198(KTC1815) NPN 5V 60V 50V 150M C103 0CE475DK618 EGR475M050T1G1C11G 4.7uF 20% 50V 50M
Q811 0TR534309AA 2SC5343Y NPN 5V 60V 50V 150MA 100NA C107 0CE227DD618 EGR227M010T1G1E11G 220uF 20% 10V 255
Q840 0TR421009CA BF421 PNP -5V -0.3KV -0.3KV -0.05A - C108 0CE475DK618 EGR475M050T1G1C11G 4.7uF 20% 50V 50M
C109 0CE226DK618 SMS5.0TP50VB22M 22uF 20% 50V 108MA -
DIODE
C111 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
D101 0DS141489AB 1N4148 1V 100V 150MA 500MA 4NSEC 500 C112 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R
D102 0DSVH00019A BA282 1V 35V 100MA 350A 1SEC 350W DO C113 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R
D11 0DS141489AB 1N4148 1V 100V 150MA 500MA 4NSEC 500 C114 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
D301 0DRDC00014M 1N4005 600V 1.1V 5UA 30A 1.5USEC DO4 C17 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R
D403 0DS141489AB 1N4148 1V 100V 150MA 500MA 4NSEC 500 C201 0CE226DF618 EGR226M016T1G1C11G 22uF 20% 16V 75MA
D405 0DRDC00014D RGP15J 600V 1300MV 5UA 50A 250NSEC D C202 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P
D406 0DRDC00014D RGP15J 600V 1300MV 5UA 50A 250NSEC D C203 0CN1010K519 RH UP050 B101K-B-B 100pF 10% 50V Y5P
D407 0DR060009AA TVR06J 600V 1300MV 5UA 25A 250NSEC D C204 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P
D424 0DRDC00014D RGP15J 600V 1300MV 5UA 50A 250NSEC D C205 0CN1010K519 RH UP050 B101K-B-B 100pF 10% 50V Y5P
D606 0DS141489AB 1N4148 1V 100V 150MA 500MA 4NSEC 500 C206 0CN1010K519 RH UP050 B101K-B-B 100pF 10% 50V Y5P
D815 0DS141489AB 1N4148 1V 100V 150MA 500MA 4NSEC 500 C207 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P

- 22 -
 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the characters at 2nd and 3rd CQ : Polyester RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

C208 0CE226DF618 EGR226M016T1G1C11G 22uF 20% 16V 75MA C556 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C209 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P C557 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C21 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA C558 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C210 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P C559 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C270 0CE227DD618 EGR227M010T1G1E11G 220uF 20% 10V 255 C561 0CQ3931N509 PEI393K2AT 39nF 10% 100V PE -40TO+85
C303 0CQ1041N409 310M 2A 104 J 100nF 5% 100V PE -40TO C562 0CQ3931N509 PEI393K2AT 39nF 10% 100V PE -40TO+85
C304 0CE107DK618 EGR107M050T6G1G11G 100uF 20% 50V 270 C563 0CN1010K519 RH UP050 B101K-B-B 100pF 10% 50V Y5P
C306 0CQ3331N509 PEI333K2AT 33nF 10% 100V PE -40TO+85 C564 0CE106DK618 SMS5.0TP50VB10M 10uF 20% 50V 72MA -4
C309 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P C569 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C402 0CE475DK618 EGR475M050T1G1C11G 4.7uF 20% 50V 50M C570 0CE107DF618 EGR107M016T1G1C11G 100uF 20% 16V 160
C403 0CQ1521N509 PEI152K2AT 1.5nF 10% 100V PE -40TO+8 C571 0CE336DD618 EGR336M010T1G1C11G 33uF 20% 10V 85MA
C404 0CE106DF618 SMS5. 0TP16VB10M 10uF 20% 16V 72MA - C572 0CN4710K519 RH UP050 B471K-B-B 470pF 10% 50V Y5P
C406 181-015G MPPS772H3VD 7.7nF 3% 1.6KV MPP -40TO C576 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C411 0CE105BR618 ESM105M250T1G5E11G 1uF 20% 250V 15MA C577 0CE106DF618 SMS5. 0TP16VB10M 10uF 20% 16V 72MA -
C413 0CK2220W515 DCM222K34Y5PL6FJ5A 2.2nF 10% 500V Y5 C578 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C414 181-091C DEHR33A471KN2A 470pF 10% 1000V Y5R - C579 0CE106DF618 SMS5. 0TP16VB10M 10uF 20% 16V 72MA -
C415 0CE108DH618 SMS5.0TP25VB1000M 1000uF 20% 25V 1.3 C580 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C416 181-009R PPN223K2DH 22nF 10% 200V PP -40TO+85 C581 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA
C417 0CK2710W515 DCM271K20Y5PL6FJ5A 270pF 10% 500V Y5 C584 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C419 0CE108DH618 SMS5.0TP25VB1000M 1000uF 20% 25V 1.3 C585 0CE225DK618 EGR225M050T1G1C11G 2.2uF 20% 50V 20M
C420 181-010R PPN222J2KH 2.2nF 5% 800V PP -40TO+85 C586 0CE225DK618 EGR225M050T1G1C11G 2.2uF 20% 50V 20M
C421 0CK2710W515 DCM271K20Y5PL6FJ5A 270pF 10% 500V Y5 C587 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R
C422 0CE475DR618 EGR475M250T1G1G11G 4.7uF 20% 250V 70 C590 0CE225DK618 EGR225M050T1G1C11G 2.2uF 20% 50V 20M
C431 181-013P MPP334J2GD 330nF 5% 400V MPP -40TO+8 C591 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C501 0CF2241L438 PCMT 365 76224 220nF 5% 63V MPE -40T C592 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA
C502 0CE225DK618 EGR225M050T1G1C11G 2.2uF 20% 50V 20M C595 181-301C NPP100V154J10F 150nF 5% 100V PP -40T
C503 0CQ6821N509 PEI682K2AT 6.8nF 10% 100V PE -40TO+8 C596 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80%
C504 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA C597 0CE106DF618 SMS5. 0TP16VB10M 10uF 20% 16V 72MA -
C505 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C599 0CN2230H949 RH TP050 F223Z-B-B 22nF -20TO+80% 25
C506 0CQ1031N509 PEI103K2AT 10nF 10% 100V PE -40TO+85 C602 0CE108DH618 SMS5.0TP25VB1000M 1000uF 20% 25V 1.3
C509 0CE106DF618 SMS5. 0TP16VB10M 10uF 20% 16V 72MA - C603 0CF2241L438 PCMT 365 76224 220nF 5% 63V MPE -40T
C510 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C604 0CN6810K519 RH UP050 B681K-B-B 680pF 10% 50V Y5P
C512 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C605 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R
C513 0CE337DD618 SMS5.0TP10VB330M 330uF 20% 10V 386MA C607 0CE476DH618 SMS5.0TP25VB47M 47uF 20% 25V 131MA -
C516 0CE226DD618 EGR226M010T1G1C11G 22uF 20% 10V 75MA C609 0CN6810K519 RH UP050 B681K-B-B 680pF 10% 50V Y5P
C519 181-007F ECQ-V1H224JL3(TR) 220nF 5% 50V MPE - C611 0CF2241L438 PCMT 365 76224 220nF 5% 63V MPE -40T
C520 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C807 181-091Q LRYM5471KHA 470pF 10% 1000V Y5R -25T
C530 0CN2220F569 RH EP050 X222K-B-B 2.2nF 10% 16V X7R C808 0CE477DH618 EGR477M025T1G1H15G 470uF 20% 25V 640
C531 0CN2230H949 RH TP050 F223Z-B-B 22nF -20TO+80% 25 C809 0CE228BF618 ESM228M016T1G5K25G 2200uF 20% 16V 97
C532 0CF4741L438 PCMT 365 76474 470nF 5% 63V MPE -40T C812 0CK47101515 DCH471K26Y5PN6FJ5A 470pF 10% 1000V Y
C533 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C813 0CE476DD618 EGR476M010T1G1C11G 47uF 20% 10V 105M
C535 0CF4741L438 PCMT 365 76474 470nF 5% 63V MPE -40T C814 181-091W LRYM27471KX1A 470pF 10% 2000V Y5R -2
C536 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C816 0CE227DP61A EGR227M160T1G1M32G 220uF 20% 160V 81
C538 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R C818 0CQ2231N509 PEI223K2AT 22nF 10% 100V PE -40TO+85
C540 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R C822 0CE108DD618 SMS5.0TP10VB1000M 1000uF 20% 10V 854
C544 0CF4741L438 PCMT 365 76474 470nF 5% 63V MPE -40T C823 181-120K SDE222M16FS1 2.2nF 20% 4000V Y5U -25
C546 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C825 0CQZVBK002C PCX2 335 91592 0.22uF 10% 275V MPP -
C547 0CF4741L438 PCMT 365 76474 470nF 5% 63V MPE -40T C826 0CE108DD618 SMS5.0TP10VB1000M 1000uF 20% 10V 854
C548 0CN2220F569 RH EP050 X222K-B-B 2.2nF 10% 16V X7R C829 0CE476DD618 EGR476M010T1G1C11G 47uF 20% 10V 105M
C551 0CE226DD618 EGR226M010T1G1C11G 22uF 20% 10V 75MA C830 0CE228DH61A EGR228M025T1G1L25G 2200uF 20% 25V 1.
C553 0CN1040K949 CH UP050 F104Z-B-B Z 100nF -20TO+80% C832 181-001V LTW227M450S1A5S40G 220uF 20% 450V 1.
C554 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA C833 0CK10202515 DCH102K39Y5PP7FJ5A 1nF 10% 2000V Y5P

- 23 -
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the characters at 2nd and 3rd CQ : Polyester RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

C834 0CK10202515 DCH102K39Y5PP7FJ5A 1nF 10% 2000V Y5P G19 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C835 0CQZVBK002A PCX2 335 M9729 0.1uF 20% 275V MPP -4 G2 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C836 0CK4710W515 DCM471K20Y5PL6FJ5A 470pF 10% 500V Y5 G21 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C838 0CE227BK618 ESM227M050T1G5H17G 220uF 20% 50V 400 G22 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C839 0CE106DH618 SMS5.0TP25VB10M 10uF 20% 25V 72MA -4 G25 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C840 0CE226BK618 ESM226M050T1G5C11G 22uF 20% 50V 85MA G26 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C841 181-011B MPPS102J3VD 1nF 5% 1.6KV MPP -40TO+8 G27 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C842 0CK1520K515 DCT152K22Y5PF6FJ5A 1.5nF 10% 50V Y5P G29 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C843 0CE105DK618 EGR105M050T1G1C11G 1uF 20% 50V 10MA G30 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C844 0CK1020K515 DCT102K20Y5PF6FJ5A 1nF 10% 50V Y5P - G31 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C845 0CK8210K515 DCT821K20Y5PF6FJ5A 820pF 10% 50V Y5P G32 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C846 0CE107DD618 SMS5.0TP10VB100M 100uF 20% 10V 157MA G38 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C848 0CE107CP618 SHL5.0TP160VB100M 100uF 20% 160V 541 G42 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C849 0CE477DD618 EGR477M010T6G1G11G 470uF 20% 10V 425 G43 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C851 0CN1020K519 RH UP050 B102K-B-B 1nF 10% 50V Y5P - G45 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C852 181-007C ECQV1H104JL3 100nF 5% 50V MPE -40TO+ G47 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C901 0CE475DR618 EGR475M250T1G1G11G 4.7uF 20% 250V 70 G48 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C903 181-033S DCH122K39Y5PP7VK7A 1.2nF 10% 2000V Y G49 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C904 0CE475DR618 EGR475M250T1G1G11G 4.7uF 20% 250V 70 G52 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C906 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R G53 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C908 0CH3104P56C C4532X7R2J104KT 100nF 10% 630V X7R - G54 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
C910 0CN5610K519 RH UP050 B561K-B-B 560pF 10% 50V Y5P G55 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
J565 0CN1030F679 RH EP050 Y103M-B-B 10nF 20% 16V X5R G56 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
G57 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
COIL & INDUCTOR
G58 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
J549 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G59 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
J578 0LA0102K119 Inductor,Wire Wound,Axial LAL02TB100K 10UH G6 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L102 0LA0102K139 Inductor,Wire Wound,Axial LAL04TB100K 10UH G61 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L204 0LA0102K119 Inductor,Wire Wound,Axial LAL02TB100K 10UH G62 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L206 0LA0102K119 Inductor,Wire Wound,Axial LAL02TB100K 10UH G7 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L207 0LA0102K119 Inductor,Wire Wound,Axial LAL02TB100K 10UH G75 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L405 6140VE0001V Coil,Linearity RT-21FA30X 60uH - - 18X35MM G76 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L406 6140VB0001F Coil,Choke CT-21Q42EF 130uH DC 500V 6.66A G77 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L501 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G79 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L503 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G8 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L504 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G80 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L505 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G81 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L506 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G84 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L507 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G89 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L509 0LA0102K119 Inductor,Wire Wound,Axial LAL02TB100K 10UH G9 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L511 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G90 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L514 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G91 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L548 0LA0121K119 Inductor,Wire Wound,Axial LAL02TB1R2K 1.2UH G94 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
L801 150-C02E Coil,Choke 50uH 50V 0A 12X17MM LEAD G95 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
T401 151-C02M Transformer,Linear EI19 10V 100V 200MH 1A 1A G96 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
T402 6174V-6006M Transformer,FBT BSC25-N1648 21” - 112V G97 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
T802 61709MC017C Transformer,Switching EER4215 270UH B+110V G99 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S
H1 6631V25034E TJC25-4Y TJC25-4Y 35097-9702_35098-9
CONNECTOR
H2 6631V25014D GIL-G GIL-G-03 35097-9702_35098-9702
G1 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S H3 6631V25014D GIL-G GIL-G-03 35097-9702_35098-9702
G13 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S H4 6631V25034E TJC25-4Y TJC25-4Y 35097-9702_35098-9
G14 336-072C BSP(C2600R) 1P LUG STRAIGHT DIP TP S P102 366-921B GIL-G-03P-S3T2-E 3P 2.54MM 1R STRAIG

- 24 -
 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the characters at 2nd and 3rd CQ : Polyester RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

P401 366-043K 35929-0410 4P 10.00MM 1R STRAIGHT DI R304 0RD0561A609 RDM92T1J5R60 5.6OHM 5% 1/2W 6.5X2.3M
P601 366-921B GIL-G-03P-S3T2-E 3P 2.54MM 1R STRAIG R306 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M
P602 366-921C GIL-G-04P-S3T2-E 4P 2.54MM 1R STRAIG R307 0RD3601F609 RD-96T1J3K60 3.6KOHM 5% 1/6W 3.2X1.8
P801A 366-043B 35929-0210 2P 10.00MM 1R STRAIGHT DI R308 0RD4302F609 RD-96T1J43K0 43KOHM 5% 1/6W 3.2X1.8M
P802A 366-043B 35929-0210 2P 10.00MM 1R STRAIGHT DI R309 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M
P903 366-009D 366-009D 1P PIN HEADER STRAIGHT DIP R310 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M
P903D 6631V25A16G GIL-J-04 GIL-J-04 400mM 2.50MM 4P UL R311 0RN0471H609 RN-92T1J4R70 4.7OHM 5% 1/2W 9.0X3.0M
P904A 366-921E GIL-G-06P-S3T2-E 6P 2.50MM 1R STRAIG R313 0RD2001F609 RD-96T1J2K00 2KOHM 5% 1/6W 3.2X1.8MM
P904B 387-B06H H-B GIL-G GIL-J 450MM 2.50MM 6P UL11 R314 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8
R315 0RN0471H609 RN-92T1J4R70 4.7OHM 5% 1/2W 9.0X3.0M
RESISTOR
R328 0RD4302F609 RD-96T1J43K0 43KOHM 5% 1/6W 3.2X1.8M
FR403 0RP0050H709 SPF92T1KR050 0.05OHM 10% 1/2W 3.2X2. R403 0RD5600A609 RDM92T1J560R 560OHM 5% 1/2W 6.5X2.3M
FR404 0RP0050H709 SPF92T1KR050 0.05OHM 10% 1/2W 3.2X2. R407 0RD0332A609 RDM92T1J33R0 33OHM 5% 1/2W 6.5X2.3MM
FR405 0RP0050H709 SPF92T1KR050 0.05OHM 10% 1/2W 3.2X2. R408 0RD6801F609 RD-96T1J6K80 6.8KOHM 5% 1/6W 3.2X1.8
FR901 0RF0241K607 FNS02T3J2R40 2.4OHM 5% 2W 12.0X4.0MM R409 0RS2202H609 RS-92T1J22K0 22KOHM 5% 1/2W 9.0X3.0M
J230 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R411 0RS1001H609 RS-92T1J1K00 1KOHM 5% 1/2W 9.0X3.0MM
J231 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R412 0RD7501A609 RDM92T1J7K50 7.5KOHM 5% 1/2W 6.5X2.3
L203 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R413 0RD1801A609 RDM92T1J1K80 1.8KOHM 5% 1/2W 6.5X2.3
L208 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R414 0RS8202H609 RS-92T 82KOHM 5% 1/2W 9.0X3.0MM NONE
L510 0RD0222A609 RDM92T1J22R0 22OHM 5% 1/2W 6.5X2.3MM R415 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M
R101 0RD3902F609 RD-96T1J39K0 39KOHM 5% 1/6W 3.2X1.8M R417 0RD8203F609 RD-96T1J820K 820KOHM 5% 1/6W 3.2X1.8
R103 0RD2202F609 RD-96T1J22K0 22KOHM 5% 1/6W 3.2X1.8M R421 0RD3600F609 RD-96T1J360R 360OHM 5% 1/6W 3.2X1.8M
R11 0RD3601F609 RD-96T1J3K60 3.6KOHM 5% 1/6W 3.2X1.8 R422 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M
R110 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R425 0RS2700K619 SML02R0J270R 270OHM 5% 2W 8.6X3.5MM
R111 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R443 0RS6800K607 RSD02T3J680R 680OHM 5% 2W 12.0X4.0MM
R112 0RD6802F609 RD-96T1J68K0 68KOHM 5% 1/6W 3.2X1.8M R458 0RS2702K607 RSD02T3J27K0 27KOHM 5% 2W 12.0X4.0MM
R117 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M R509 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R119 0RD3301F609 RD-96T1J3K30 3.3KOHM 5% 1/6W 3.2X1.8 R510 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R12 0RD2401F609 RD-96T1J2K40 2.4KOHM 5% 1/6W 3.2X1.8 R511 0RD3301F609 RD-96T1J3K30 3.3KOHM 5% 1/6W 3.2X1.8
R120 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 R512 0RD3301F609 RD-96T1J3K30 3.3KOHM 5% 1/6W 3.2X1.8
R121 0RD2201F609 RD-96T1J2K20 2.2KOHM 5% 1/6W 3.2X1.8 R513 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R13 0RD1801F609 RD-96T1J1K80 1.8KOHM 5% 1/6W 3.2X1.8 R518 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R14 0RD1501F609 RD-96T1J1K50 1.5KOHM 5% 1/6W 3.2X1.8 R521 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R15 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M R522 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R16 0RD5601F609 RD-96T1J5K60 5.6KOHM 5% 1/6W 3.2X1.8 R523 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R17 0RD3300F609 RD-96T1J330R 330OHM 5% 1/6W 3.2X1.8M R524 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM
R19 0RD1301F609 RD-96T1J1K30 1.3KOHM 5% 1/6W 3.2X1.8 R525 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM
R203 0RD0682F609 RD-96T1J68R0 68OHM 5% 1/6W 3.2X1.8MM R534 0RD1504F609 CR1/8TB1M5J 1.5MOHM 5% 1/8W 3.2X1.8M
R204 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM R536 0RD1801F609 RD-96T1J1K80 1.8KOHM 5% 1/6W 3.2X1.8
R205 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM R537 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM
R206 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM R538 0RD1803F609 RD-96T1J180K 180KOHM 5% 1/6W 3.2X1.8
R207 0RD5602F609 RD-96T1J56K0 56KOHM 5% 1/6W 3.2X1.8M R539 0RD1003F609 RD-96T1J100K 100KOHM 5% 1/6W 3.2X1.8
R212 0RD1201A609 RDM92T1J1K20 1.2KOHM 5% 1/2W 6.5X2.3 R540 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R215 0RD2402F609 RD-96T1J24K0 24KOHM 5% 1/6W 3.2X1.8M R543 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R225 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R545 0RD0752F609 RD-96T1J75R0 75OHM 5% 1/6W 3.2X1.8MM
R226 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R547 0RD1203F609 RD-96T1J120K 120KOHM 5% 1/6W 3.2X1.8
R227 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R548 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R228 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R549 0RD3301F609 RD-96T1J3K30 3.3KOHM 5% 1/6W 3.2X1.8
R23 0RD0151A609 RDM92T1J1R50 1.5OHM 5% 1/2W 6.5X2.3M R550 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R252 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R551 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R253 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R552 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M
R303 0RD2400A609 RDM92T1J240R 240OHM 5% 1/2W 6.5X2.3M R553 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M

- 25 -
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the characters at 2nd and 3rd CQ : Polyester RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

R554 0RD1501F609 RD-96T1J1K50 1.5KOHM 5% 1/6W 3.2X1.8 R836 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM
R555 0RD6800F609 RD-96T1J680R 680OHM 5% 1/6W 3.2X1.8M R838 0RD2200A609 RDM92T1J220R 220OHM 5% 1/2W 6.5X2.3M
R556 0RN3902F409 RN-96T1F39K0 39KOHM 1% 1/6W 3.2X1.8M R839 0RD1003F609 RD-96T1J100K 100KOHM 5% 1/6W 3.2X1.8
R557 0RD1202F609 RD-96T1J12K0 12KOHM 5% 1/6W 3.2X1.8M R841 0RF0391K607 FNS02T3J3R90 3.9OHM 5% 2W 12.0X4.0MM
R558 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M R842 0RD2201F609 RD-96T1J2K20 2.2KOHM 5% 1/6W 3.2X1.8
R562 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R843 0RD2203F609 RD-96T1J220K 220KOHM 5% 1/6W 3.2X1.8
R563 0RD1501A609 RDM92T1J1K50 1.5KOHM 5% 1/2W 6.5X2.3 R844 0RD1501F609 RD-96T1J1K50 1.5KOHM 5% 1/6W 3.2X1.8
R566 0RN4701F409 RN-96T1F4K70 4.7KOHM 1% 1/6W 3.2X1.8 R845 0RD0332F609 RD-96T1J33R0 33OHM 5% 1/6W 3.2X1.8MM
R567 0RN4701F409 RN-96T1F4K70 4.7KOHM 1% 1/6W 3.2X1.8 R846 180-A01D PRW02T3JR160 0.16OHM 5% 2W 12.0X4.0M
R568 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M R847 0RD4300F609 RD-96T1J430R 430OHM 5% 1/6W 3.2X1.8M
R569 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM R848 0RS4702K619 SML02R0J47K0 47KOHM 5% 2W 8.6X3.5MM
R572 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R849 0RS4702K607 RSD02T3J47K0 47KOHM 5% 2W 12.0X4.0MM
R576 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M R850 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8
R577 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M R851 0RD8202F609 RD-96T1J82K0 82KOHM 5% 1/6W 3.2X1.8M
R580 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 R852 0RD1003F609 RD-96T1J100K 100KOHM 5% 1/6W 3.2X1.8
R581 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 R853 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM
R582 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R856 180-822N RWR07PDJ1R00 1OHM 5% 7W 36X9.5X9.5MM
R583 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R858 0RKZVTA001K RN-92T1J470K 470KOHM 5% 1/2W 9.0X3.0
R584 0RD0101F609 RD-96T1J1R00 1OHM 5% 1/6W 3.2X1.8MM R859 0RD1002A609 RDM92T1J10K0 10KOHM 5% 1/2W 6.5X2.3M
R585 0RD0101F609 RD-96T1J1R00 1OHM 5% 1/6W 3.2X1.8MM R860 0RF0221K607 FNS02T3J2R20 2.2OHM 5% 2W 12.0X4.0MM
R587 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R861 0RD3901F609 RD-96T1J3K90 3.9KOHM 5% 1/6W 3.2X1.8
R591 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R901 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R592 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R902 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R595 0RD6800F609 RD-96T1J680R 680OHM 5% 1/6W 3.2X1.8M R903 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R606 0RD8202F609 RD-96T1J82K0 82KOHM 5% 1/6W 3.2X1.8M R906 0RD1201A609 RDM92T1J1K20 1.2KOHM 5% 1/2W 6.5X2.3
R608 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R907 0RD1201A609 RDM92T1J1K20 1.2KOHM 5% 1/2W 6.5X2.3
R611 0RD1202F609 RD-96T1J12K0 12KOHM 5% 1/6W 3.2X1.8M R908 0RD1201A609 RDM92T1J1K20 1.2KOHM 5% 1/2W 6.5X2.3
R612 0RD8202F609 RD-96T1J82K0 82KOHM 5% 1/6W 3.2X1.8M R909 0RS2201H609 RSD92T1J2K20 2.2KOHM 5% 1/2W 6.5X2.3
R613 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R910 0RS2201H609 RSD92T1J2K20 2.2KOHM 5% 1/2W 6.5X2.3
R616 0RD7502F609 RD-96T1J75K0 75KOHM 5% 1/6W 3.2X1.8M R911 0RS2201H609 RSD92T1J2K20 2.2KOHM 5% 1/2W 6.5X2.3
R617 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M R912 0RD2204A609 RDM92T1J2M20 2.2MOHM 5% 1/2W 6.5X2.3
R618 0RD4702F609 RD-96T1J47K0 47KOHM 5% 1/6W 3.2X1.8M R920 0RD4703A609 RDM92T1J470K 470KOHM 5% 1/2W 6.5X2.3
R619 0RD7502F609 RD-96T1J75K0 75KOHM 5% 1/6W 3.2X1.8M R925 0RD2200F609 RD-96T1J220R 220OHM 5% 1/6W 3.2X1.8M
R811 0RD1002F609 RD-96T1J10K0 10KOHM 5% 1/6W 3.2X1.8M
R812 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8
SWITCH
R813 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM SW11 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R816 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 SW12 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R817 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 SW13 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R819 0RP0050H709 SPF92T1KR050 0.05OHM 10% 1/2W 3.2X2. SW14 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R820 0RD1000F609 RD-96T1J100R 100OHM 5% 1/6W 3.2X1.8M SW15 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R821 0RD4701F609 RD-96T1J4K70 4.7KOHM 5% 1/6W 3.2X1.8 SW16 140-315A THVH472GBC 1C1P 12VDC 0.05A VERTICAL
R822 0RP0020J809 SPF01T1MR020 0.02OHM 20% 1W 6.5X2.3M SW801 6600VM1001A SDKLA1 AC 250VAC 5A 1PCS 1C1P VERTIC
R823 0RP0020J809 SPF01T1MR020 0.02OHM 20% 1W 6.5X2.3M
R824 0RD2701F609 RD-96T1J2K70 2.7KOHM 5% 1/6W 3.2X1.8
SPARK GAP, AXIAL
R825 0RD1001F609 RD-96T1J1K00 1KOHM 5% 1/6W 3.2X1.8MM SG901 165-004A 152F-L3N/S-23 RADIAL 1.5KV 1.5KV - 5
R826 0RD0472F609 RD-96T1J47R0 47OHM 5% 1/6W 3.2X1.8MM SG902 165-004A 152F-L3N/S-23 RADIAL 1.5KV 1.5KV - 5
R829 0RP0050H709 SPF92T1KR050 0.05OHM 10% 1/2W 3.2X2. SG903 165-004A 152F-L3N/S-23 RADIAL 1.5KV 1.5KV - 5
R830 0RN1803F409 RN-96T1F180K 180KOHM 1% 1/6W 3.2X1.8 SG904 6918VAX002H WSP-122N AXIAL 1.2KV 1.2KV - - TP
R831 0RN2402F409 RN-96T1F24K0 24KOHM 1% 1/6W 3.2X1.8M SG911 6918VAX002E WSP-351M AXIAL 350V 350V - 7.5MM TP
R832 0RD3902F609 RD-96T1J39K0 39KOHM 5% 1/6W 3.2X1.8M SG912 6918VAX002E WSP-351M AXIAL 350V 350V - 7.5MM TP
R834 0RN4701F409 RN-96T1F4K70 4.7KOHM 1% 1/6W 3.2X1.8 SG913 6918VAX002E WSP-351M AXIAL 350V 350V - 7.5MM TP
R835 0RKZVTA001C RN-92T1J8M20 8.2MOHM 5% 1/2W 9.0X3.0

- 26 -
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

FILTER & CRYSTAL

FB401 125-022K 125-022K 20OHM 3.5X6MM AXIAL TP
FB802 125-022K 125-022K 20OHM 3.5X6MM AXIAL TP
FB803 125-022K 125-022K 20OHM 3.5X6MM AXIAL TP
FB833 125-022K 125-022K 20OHM 3.5X6MM AXIAL TP
FB846 125-022R BI3857 30OHM 3.6X5.7MM AXIAL TP
T803 150-F06W 150-F06W 27MH 32X22X38MM SQE2930S RA
X01 156-A01Z HC-49/U 24.576MHZ 50PPM 24.576MHZ 50
Z101 166-A01B K3953M 33.90MHZ 38.90MHZ 17X3.9X8.7M
Z102 6200QL3003G K9650M(B39389-K9650-M100) 33.90_38.9

MISCELLANEOUS
B1 3890900038B Box 21FB50 NEW BOX 21” DWR2 715-560-537”
B2 3890900097D BOX DW2 1094 1124 100 1 COLOR MC049B
B3 3890900096D BOX DW2 1074 1104 1080 1 COLOR MC049
B4 MAY34754602 BOX DW2 715 560 537 2 COLOR MC049B
B5 MAY30420601 BOX DW 676 524 510 2 COLOR TDR
F801 0FS4001B51D Fuse,Time Delay 0218 004. GLASS 250V 4A
JK202 6612M00005A Jack,Scart UPJ-R1-027 21P 21P/1C 3.81MM
PA11 6726VV0006H Receiver Module TSOP2238NN1 4.5TO5.5V
PJ201 6613V00006G Jack,RCA PJ6062G 15MM 2RX1C ANGLE BK
RL802 6920VB1001E Relay,Contact SDT-S-105LMR AC250V/DC30V
SK901 6620VBC003A Socket,CRT PCS030A 8P STRAIGHT 15.24MM
TH801 163-058D Thermistor,PTC J503P83D070M290X 14OHM
TU101 6700MF0018A Tuner,Analog TAEA-G011D PAL-B/G+I+M+D/K
VD801 164-003G Varistor TVR14621 620V 10% 250pF 14MM

ACCESSORIES
A1 MFL30441111 Manual,Owners USER CW62B LG MA-MK
A1 MFL30441112 Manual,Owners USER CW62B LG MA-PL
A1 MFL30441115 Manual,Owners USER CW62B LG MA-CZ
A1 MFL30441125 Manual,Owners USER CW62B LG MA-MK
A1 MFL30441126 Manual EN/SE/HU/BU/LV/LT/ES/SK/CZ/RO/PL
A1 MFL30441113 Manual,Owners USER CW62B LG MA-RO
A2 MKJ30036802 Remote Controller MOLD HIPS 60HR CW62A
A3 5010V00004D Antenna,Rod 3SECTION 750MM NTSC

- 27 -
P/No : EBY31683801
SVC. SHEET : EBY31683801-S