Product Fact Sheet

Industrial
e·MMC Memory

EM-36 Series
JEDEC e·MMC 5.1 compliant,
BGA 100 ball, Enhanced Mode (pSLC)

Industrial Temperature Grade

Date : Marc h 6 , 2 0 2 4
Re vi si o n: 1 .0 1
 Product Fact Sheet
EM-36 Series
Product Summary
• Capacities: 5 GBytes, 10 GBytes, 20 GBytes, 40 GBytes, 80 GBytes
• Operating Temperature Range1: Industrial Operating Temperature (Tambient) -40 to 85°C
• Endurance in TeraBytes Written (TBW) @ Max Capacity2: up to 2652

Product Features
• Fully compliant with JEDEC e·MMC 5.1 Standard (JESD84-B51)
• 100-ball BGA, 1.0mm pitch
• 14 x 18mm, RoHS compliant
• 3D TLC NAND base technology in Enhanced Mode (pSLC)
• Industrial Operating Temperature -40 to 85°C
• Single enhanced mode partition
• High performance e·MMC 5.1 specification
o Eleven-wire bus (clock, Data Strobe, 1 bit command, 8 bit data bus) and a hardware reset
o Three different data bus width modes: 1-bit (default), 4-bit, and 8-bit
o Clock frequencies 0-200MHz, High Speed Mode HS400
o Command Queue Feature according to e·MMC Spec 5.1
o Up to 300MB/s sequential read and up to 230MB/s sequential write
• Power Supply: (Low-power CMOS technology)
o VCCQ 1.7V…1.95V or 2.7V…3.6V e·MMC supply
o VCC 2.7V…3.6V NAND Flash supply
• Optimized FW algorithms
o Power-fail data loss protection
o Wear Leveling technology
Equal wear leveling of static and dynamic data. The wear leveling assures that dynamic data
as well as static data is balanced evenly across the memory. With that the maximum write
endurance of the device is ensured
o Read Disturb Management
The read commands per region are monitored and the content is conditionally refreshed
when critical levels have occurred
o Auto Read Refresh
The interruptible background process maintains the user data for Read Disturb effects or
Retention degradation due to high temperature effects
o Diagnostic features with Device Health Report according to e·MMC Spec 5.1, and detailed
Lifetime Monitor data (Swissbit proprietary, accessible through standard e·MMC commands).
o Field Firmware update3 according to e·MMC Spec 5.1
o Discard and Sanitize, Trim
o Boot Operation Mode and Alternative Boot Operation Mode
o Replay Protected Memory Block (RPMB)
• High reliability
o Designed with sophisticated firmware architecture for industrial and embedded markets.
o Enhanced Mode (pSLC) with higher write performance and endurance than 3D TLC configured
products (EM-30).
o Ideal for application like POS/POI, PLC, IoT, gaming, medical and use as general boot medium for
embedded applications.
o The product is optimized for long life cycle that requires superior data retention as well as
power fail safety.

1
Adequate airflow is required to ensure the temperature Tcase does not exceed 95°C (industrial temperature drive)
2
According to JEDEC (JESD47I), the time to write the full TBW is a minimum of 18 months. Higher average daily data volume reduces the
specified TBW. The values listed are estimates and are subject to change without notice.
3
The support of In-Field FW update capabilities on host systems is recommended. The update must be transferred with a CMD25. For Linux,
kernel 4.4 or higher is required.
Swissbit AG Revision: 1.01
Industriestrasse 4 TLP: Swissbit public Template: Doc-4991
CH-9552 Bronschhofen File: EM-36_100-ball_fact_sheet_Rev101
Switzerland www.swissbit.com/contact Page 2 of 3
 Product Fact Sheet
EM-36 Series
o Controlled BOM & PCN process

1 Order Information for EM-36

Density Part Number Industrial Temp. Range Firmware Flash Technology
5GB SFEM005GB1ED1TO-I-5E-31P-STD
10GB SFEM010GB1ED1TO-I-5E-31P-STD
3D TLC NAND
20GB SFEM020GB1ED1TO-I-6F-31P-STD -40°C to 85°C FW1: default Flash in pSLC
Mode
40GB SFEM040GB1ED1TO-I-7G-31P-STD
80GB SFEM080GB1ED1TO-I-8H-31P-STD

1.1 System Performance

System Performance, HS400 Max. reliable mode Unit
Burst Data transfer Rate HS400 (max clock 200MHz) 400
Sequential Read up to 300 MB/s
Sequential Write up to 230

1.2 Current Consumption

Typ. ICCQ current Typ. ICC current
Current Consumption, HS400, Max. Density Unit
@ VCCQ 1.8V @ VCC 3.3V
Write 99 97
Read 138 108 mA
Sleep 0.07 0.07

1.3 Physical Dimensions

Physical Dimensions Value Unit
Length 18±0.1
Width 14±0.1 mm
Thickness 1.4 max.

1.4 Recommended Temperature Conditions

Parameter Min. Typ. Max. Unit
Industrial Operating / Storage Temperature -40 25 85* °C
* High temperature storage without operation reduces the data retention, in operation the data will be refreshed, if data error issues
were detected

For more information on e·MMC interface, please visit JEDEC homepage (www.jedec.org)

Why Swissbit?
Swissbit is focused on the design, development, manufacture, and support of leading edge memory and storage
solutions for the worldwide OEM/ODM marketplace. As a global supplier, Swissbit recognizes and addressees the
higher level of application requirements of today’s industrial, Netcom, and automotive customers by providing
best-in-class products and services, with uncompromised attention to driving overall value and quality.

Swissbit AG Revision: 1.01

Industriestrasse 4 TLP: Swissbit public Template: Doc-4991
CH-9552 Bronschhofen File: EM-36_100-ball_fact_sheet_Rev101
Switzerland www.swissbit.com/contact Page 3 of 3