Product Fact Sheet
Industrial / Automotive
e·MMC Memory
EM-36 Series
JEDEC e·MMC 5.1 compliant,
BGA 153 ball, Enhanced Mode (pSLC)
AEC – Q100 Grade 2
Industrial / Automotive
Temperature Grade
Date : Marc h 6 , 2 0 2 4
Re vi si o n: 1 .05
Product Fact Sheet
EM-36 Series
Product Summary
• Capacities: 5 GBytes, 10 GBytes, 20 GBytes, 40 GBytes, 80 GBytes
• Operating Temperature Range1:
o Industrial Operating Temperature (Tambient) -40 to 85°C
o Automotive Operating Temperature (Tambient) -40 to 105°C
ATS 2 Products2 (Assembly Test Site 2): AEC – Q100 Grade 2 certified, not available for 5 GBytes
• Endurance in TeraBytes Written (TBW) @ Max Capacity2: up to 4169
Product Features
• Fully compliant with JEDEC e·MMC 5.1 Standard (JESD84-B51)
• 153-ball BGA, 0.5mm pitch
• 11.5 x 13mm, RoHS compliant
• 3D TLC NAND base technology in Enhanced Mode (pSLC)
• Single enhanced mode partition
• High performance e·MMC 5.1 specification
o Eleven-wire bus (clock, Data Strobe, 1 bit command, 8 bit data bus) and a hardware reset
o Three different data bus width modes: 1-bit (default), 4-bit, and 8-bit
o Clock frequencies 0-200MHz, High Speed Mode HS400
o Command Queue Feature according to e·MMC Spec 5.1
o Up to 330MB/s sequential read and up to 250MB/s sequential write
• Power Supply: (Low-power CMOS technology)
o VCCQ 1.7V…1.95V or 2.7V…3.6V e·MMC supply
o VCC 2.7V…3.6V NAND Flash supply
• Optimized FW algorithms
o Power-fail data loss protection
o Wear Leveling technology
Equal wear leveling of static and dynamic data. The wear leveling assures that dynamic data
as well as static data is balanced evenly across the memory. With that the maximum write
endurance of the device is ensured
o Read Disturb Management
The read commands per region are monitored and the content is conditionally refreshed
when critical levels have occurred
o Auto Read Refresh
The interruptible background process maintains the user data for Read Disturb effects or
Retention degradation due to high temperature effects
o Diagnostic features with Device Health Report according to e·MMC Spec 5.1, and detailed
Lifetime Monitor data (Swissbit proprietary, accessible through standard e·MMC commands).
o Field Firmware update3 according to e·MMC Spec 5.1
o Discard and Sanitize, Trim
o Boot Operation Mode and Alternative Boot Operation Mode
o Replay Protected Memory Block (RPMB)
1
Adequate airflow is required to ensure the temperature Tcase does not exceed 95°C (industrial temperature drive), respectively 115°C
(automotive temperature drive)
2
According to JEDEC (JESD47I), the time to write the full TBW is a minimum of 18 months. Higher average daily data volume reduces the
specified TBW. The values listed are estimates and are subject to change without notice.
3
The support of In-Field FW update capabilities on host systems is recommended. The update must be transferred with a CMD25. For Linux,
kernel 4.4 or higher is required.
Swissbit AG Revision: 1.05
Industriestrasse 4 TLP: Swissbit public Template: Doc-4991
CH-9552 Bronschhofen File: EM-36_fact_sheet_Rev105
Switzerland www.swissbit.com/contact Page 2 of 4
Product Fact Sheet
EM-36 Series
• High reliability
o Designed with sophisticated firmware architecture for industrial and embedded markets.
o Enhanced Mode (pSLC) with higher write performance and endurance than 3D TLC configured
products (EM-30).
o Ideal for application like POS/POI, PLC, IoT, gaming, medical and use as general boot medium for
embedded applications.
o The product is optimized for long life cycle that requires superior data retention as well as
power fail safety.
o Controlled BOM & PCN process
1 Order Information for EM-36
Table 1: Available Part Numbers
ATS 1 Gen3 Flash
Temperature
Capacity Industrial (-40 to 85°C) Automotive (-40 to 105°C)
Part Number Part Number
5 GBytes SFEM005GB1ED1TO-I-5E-11P-STD -
10 GBytes SFEM010GB1ED1TO-I-5E-11P-STD -
20 GBytes SFEM020GB1ED1TO-I-6F-11P-STD -
40 GBytes SFEM040GB1ED1TO-I-7G-11P-STD -
80 GBytes SFEM080GB1ED1TO-I-8H-11P-STD -
ATS 1 (Assembly Test Site 1)
Table 2: Available Part Numbers
ATS 2 Gen3 Flash
Temperature
Capacity Industrial (-40 to 85°C) Automotive (-40 to 105°C)
Part Number Part Number
5 GBytes SFEM005GB2ED1TO-I-5E-11P-STD SFEM005GB2ED1TO-A-5E-11P-STD
10 GBytes SFEM010GB2ED1TO-I-5E-11P-STD SFEM010GB2ED1TO-A-5E-11P-STD
20 GBytes SFEM020GB2ED1TO-I-6F-11P-STD SFEM020GB2ED1TO-A-6F-11P-STD
40 GBytes SFEM040GB2ED1TO-I-7G-11P-STD SFEM040GB2ED1TO-A-7G-11P-STD
ATS 2 (Assembly Test Site 2)
Table 3: Available Part Numbers
ATS 2 Gen5 Flash
Temperature
Capacity Industrial (-40 to 85°C) Automotive (-40 to 105°C)
Part Number Part Number
20 GBytes SFEM020GB2ED1TB-I-CE-11P-STD SFEM020GB2ED1TB-A-CE-11P-STD
40 GBytes SFEM040GB2ED1TB-I-EF-11P-STD SFEM040GB2ED1TB-A-EF-11P-STD
80 GBytes SFEM080GB2ED1TB-I-VG-11P-STD SFEM080GB2ED1TB-A-VG-11P-STD
ATS 2 (Assembly Test Site 2)
Swissbit AG Revision: 1.05
Industriestrasse 4 TLP: Swissbit public Template: Doc-4991
CH-9552 Bronschhofen File: EM-36_fact_sheet_Rev105
Switzerland www.swissbit.com/contact Page 3 of 4
Product Fact Sheet
EM-36 Series
1.1 System Performance
Gen3 Flash
System Performance, HS400 Max. reliable mode Unit
Burst Data transfer Rate HS400 (max clock 200MHz) 400
Sequential Read up to 320 MB/s
Sequential Write up to 240
Gen5 Flash
System Performance, HS400 Max. reliable mode Unit
Burst Data transfer Rate HS400 (max clock 200MHz) 400
Sequential Read up to 330 MB/s
Sequential Write up to 250
1.2 Current Consumption
Gen3 Flash
Typ. ICCQ current Typ. ICC current
Current Consumption, HS400, Max. Density Unit
@ VCCQ 1.8V @ VCC 3.3V
Write 99 97
Read 138 108 mA
Sleep 0.07 0.07
Gen5 Flash
Typ. ICCQ current Typ. ICC current
Current Consumption, HS400, Max. Density Unit
@ VCCQ 1.8V @ VCC 3.3V
Write 102 104
Read 142 105 mA
Sleep 0.06 0.04
1.3 Physical Dimensions
Physical Dimensions Value Unit
Length 13±0.1
Width 11.5±0.1 mm
Thickness 1.2 max.
1.4 Recommended Temperature Conditions
Parameter Min. Typ. Max. Unit
Industrial Operating Temperature -40 25 85 °C
Automotive Operating Temperature -40 25 105 °C
* High temperature storage without operation reduces the data retention, in operation the data will be refreshed, if data error issues
were detected
For more information on e·MMC interface, please visit JEDEC homepage (www.jedec.org)
Why Swissbit?
Swissbit is focused on the design, development, manufacture, and support of leading edge memory and storage
solutions for the worldwide OEM/ODM marketplace. As a global supplier, Swissbit recognizes and addressees the
higher level of application requirements of today’s industrial, Netcom, and automotive customers by providing
best-in-class products and services, with uncompromised attention to driving overall value and quality.
Swissbit AG Revision: 1.05
Industriestrasse 4 TLP: Swissbit public Template: Doc-4991
CH-9552 Bronschhofen File: EM-36_fact_sheet_Rev105
Switzerland www.swissbit.com/contact Page 4 of 4
