SPECIFICATIONS M1400/M1400i
Continuous Average Output Power, both channels driven:
250 watts per channel into 8 ohms from 20Hz to 20kHz, with no more than 0.012% THD 425 watts per channel into 4 ohms from 20Hz to 20kHz, with no more than 0.025% THD 630 watts per channel into 2 ohms from 20Hz to 20kHz, with no more than 0.050% THD
> 40 dB, 20Hz to 20kHz
Load Angle:
8(jx) time independent at 8 4(jx) time dependent, T > 6 min. at 4 2(1jx) time dependent, T > 2 min. at 2
Transient Recovery:
< 1s for 20 dB overdrive @ 1kHz
High Frequency Overload and Latching:
No latch up at any frequency or level.
High Frequency Stability:
Unconditionally stable driving any reactive or capacitive load.
Bridged mono operation:
850 watts into 8 ohms from 20Hz to 20kHz, with no more than 0.025% THD 1260 watts into 4 ohms from 20Hz to 20kHz, with no more than 0.050% THD
Turn On Delay:
3 seconds
Variable Low-Cut Filter:
10Hz (Off) to 170Hz, 2nd Order Bessel
Maximum Power at 1% THD:
300 watts per channel into 8 ohms 500 watts per channel into 4 ohms 700 watts per channel into 2 ohms 1000 watts into 8 ohms bridged 1400 watts into 4 ohms bridged Note: Power ratings are specified at 120VAC (U.S. and Canada) and 240VAC (Export) line voltages. The M1400/M1400i power amplifier draws large amounts of current from the AC line with continuous sine wave testing. Accurate measurement of power requires a steady and stable AC supply. This means the line impedance must be very low to insure that the peak AC line voltage does not sag to less than 97% of its value.
Subwoofer Low-Pass Filter:
Switched: 63Hz/125Hz, 3rd Order Bessel
Constant Directivity High Frequency Boost:
2kHz to 6kHz (+3 dB points) 6 dB/octave high-frequency shelving filter, (shelving occurs at approximately 30kHz)
Limiter Section:
Complementary Positive and Negative Peak Detecting
Indicators:
6 meter LEDs per channel SIG (Signal Present), 20, 9, 6, 3, OL (Overload) CH 1 & 2 PROTECT LEDs SHORT LEDs TEMP STATUS COLD/HOT LEDs
If driving highly reactive loads, we recommend that the limiter circuit be engaged.
Power Bandwidth:
20Hz to 70kHz (+0, 3 dB)
Power Consumption:
65 watts at idle 900 watts with musical program fully loaded (2 ohms per side, or 4 ohms bridged) 550 watts with musical program fully loaded (4 ohms per side, or 8 ohms bridged) 850 watts at full power into 8 ohms (continuous sine wave) 1500 watts at full power into 4 ohms (continuous sine wave) 2500 watts at full power into 2 ohms (continuous sine wave)
Frequency Response:
20Hz to 40kHz (+0, 1 dB) 10Hz to 70kHz (+0, 3 dB)
Distortion:
THD, SMPTE IMD, TIM < 0.025% @ 8 < 0.050% @ 4 < 0.150% @ 2
Signal-to-Noise Ratio:
> 107 dB below rated power into 4 ohms
Channel Separation:
> 80 dB @ 1kHz
AC Line Power:
U.S./Canada 120VAC, 60Hz Europe 240VAC, 50Hz Japan 100VAC, 50/60Hz Korea 220VAC, 60Hz
Damping Factor:
> 350 from 0 to 400Hz
Input Impedance:
20k balanced bridging
Input Sensitivity:
1.23 volts (+4 dBu) for rated power into 4 ohms
AC Drop-out Voltage:
At approximately 50% of rated line voltage
Gain:
30.25 dB (32.5V/V)
Physical:
Height 3.5 inches (89mm) Width 19.0 inches (483mm) Depth 15.25 inches (387mm) Overall Depth 16.25 inches (413mm) Weight 36 pounds (16.3kg) Since we are always striving to make our stuff better at Mackie Designs by incorporating new and improved materials, components, and manufacturing methods, we reserve the right to change these specifications at any time without notice.+
Maximum Input Level:
9.75 volts (+22 dBu)
Rise Time:
< 4.4s
Slew Rate:
Voltage Slew Rate > 50V/s > 100V/s bridged Current Slew Rate > 32A/s at 2
CMRR:
JUICE SERIES SPECIFICATIONS
Continuous Sine Wave Average Output Power for each channel with both channels driven, 20 Hz to 20 kHz
J800 J1400 J2500 2 ohms: 480 W 800 W 1400 W 4 ohms: 300 W 450 W 750 W 8 ohms: 205 W 310 W 575 W
AC Power Requirements
U.S. 120 VAC, 60 Hz Europe 240 VAC, 50 Hz Japan 100 VAC, 50/60 Hz Korea 220 VAC, 60 Hz
Physical Dimensions and Weight
Height: 3.5 in/89 mm Width: 19.0 in/483 mm Depth: 15.7 in/400 mm Weight: J800: 43.6 lb/19.8 kg J1400: 48.5 lb/22.0 kg J2500: 56.2 lb/25.5 kg .
Bridged Mono Operation, 20 Hz to 20 kHz
J800 J1400 J2500 4 ohms: 800 W 1400 W 2500 W 8 ohms: 560 W 900 W 1500 W Note: Power ratings are specified at 120 VAC line voltage.
Power Bandwidth
5 Hz to 50 kHz (+0, 3 dB)
Frequency Response
25 Hz to 25 kHz (+0, 1 dB)
Distortion
THD and SMPTE IMD; 20Hz to 20kHz < 0.03% @ 8 ohms
Signal-to-Noise Ratio
> 100 dB below rated power into 4 ohms
Channel Separation
> 90 dB @ 1 kHz
Damping Factor
> 300 @ 1 kHz and below
Input Impedance
20 k balanced 10 k unbalanced
Input Sensitivity
1.15 V (+3.4 dBu) for rated power into 4 ohms
Gain
J800: 30 dB J1400: 32 dB J2500: 34 Db
Maximum Input Level
9.75 Vrms (+22 dBu)
Turn On Delay
2.5 seconds
Subsonic Filter
9 dB @ 30 Hz
Topology
J800, J1400: Class AB J2500: Class H
Cooling
Dual variable-speed fans with back to front airflow
Indicators
Channels A and B SIG (Signal Present), OL (Overload) POWER
Current Consumption
J800 J1400 J2500 Idle 0.5 A 0.5 A 1.0 A Musical Program @ 8 3.9 A 5.1 A 8.1 A Musical Program @ 4 5.0 A 6.7 A 10.0 A Musical Program @ 2 7.0 A 10.6 A 17.2 A
