Republic of the Philippines

Department of Education
Region IV-A CALABARZON
CITY SCHOOLS DIVISION OFFICE OF ANTIPOLO
MAXIMO L. GATLABAYAN MEMORIAL NATIONAL HIGH SCHOOL

SECOND QUARTERLY EXAMINATION

COMPUTER SYSTEMS SERVICING TLE 8
S.Y. 2023-2024
Name: _____________________________________________________________Date: __________
Grade & Section: ____________________________________________________Score: _________
I. MULTIPLE CHOICE:
Directions: Read the following questions below carefully. Write the letter of the correct
answer on your answer sheet.
1. Lina wants to clean her keyboard without scratching or leaving debris. Which tool is used to
clean the different computer components?
A. Cable ties B. Flat head screwdriver C. Lint-free Cloth D. Part Retriever
2. Ana used a material which keeps the cable wires from running across the floor, and to bundle
cables neatly inside and outside of a computer. What material did she use?
A. Cable ties B. Flat head screwdriver C. Lint-free Cloth D. Part Retriever
3. Your teacher asked you to use slotted screws in your performance task. Which tool should be
used?
A. Cable ties B. Flat head screwdriver C. Lint-free Cloth D. Part Retriever
4. Lito needs to open his laptop to fix his grounded keyboard. Which tool is used to loosen or
tighten screws that have a star-like depression on the top, and a feature that is mainly found on
laptop?
A. Anti-static mat B. Philips head screwdriver C. Torx screwdriver D. Wire cutter
5. You must clean the keyboard by blowing away the dust and debris without touching the
components. Which tool should be used?
A. Anti-static mat B. Compressed air C. Hex driver D. Wire cutter
6. Gina decided to clean her personal computer. To prevent static electricity from building up,
what tool is she going to use?
A. Anti-static mat B. Compressed air C. Hex driver D. Wire cutter
7. Melissa needs to fix the damage cellphone but, she encountered the screw like a positive sign
or cross-head screws. Which tool should be used?
A. Anti-static mat B. Hex driver C. Philips head screwdriver D. Wire cutter
8. Robert wants to adjust the break of his bicycle, but each screw has hexagonal slot heads.
Which of the following tools below must be used by Robert to adjust the break of his bicycle?
A. Anti-static mat B. Hex driver C. Philips head screwdriver D. Wire cutter
9. This tool is usually used by electricians for them to strip and cut wires. What do you think is
this tool?
A. Anti-static mat B. Hex driver C. Philips head screwdriver D. Wire cutter
10. Roy wants to repair his personal computer but it’s hard for him to retrieve parts from the
location because some parts of his computer are too small for his hand to fit? What do you think
is the best tool that Roy can use?
A. Cable ties B. Flat head screwdriver C. Lint-free Cloth D. Part Retriever
11. A successful task can be achieved through __________planning and preparation.
A. careful and proper B. constant C. courageous D. seldom
12. Good preparation will boost your __________.
A. confidence B. intelligence C. skill D. weakness
13. One of the factors to consider when planning and preparing for the task to avoid accident is
__________.
A. materials B. safety C. place D. waste disposal
14. When the task calls for the removal of parts, use __________.
A. cleaning tools B. loosening tools C. marking tools D. measuring tools
15. Anything that could hurt you or someone else.
A. Hazard B. Risk C. Occupational safety D. Occupational
procedure

Sitio Paenaan, San Jose, Antipolo City

Telephone No.: (02) 8425-1807
16. Which of the following is an input device?
A. Keyboard B. Monitor C. Printer D. Speaker
17. What kind of input device that optically "reads" the image and converts it into a digital
signal?
A. Microphone B. Printer C. Scanner D. Webcam
18. Marco wants to access information on the World Wide Web because he can't find the answer
to his assignment in his notebook. What kind of applications software he must use?
A. Business application software B. Internet C. Web browser D. Word processing
19. Which of the following is primary storage?
A. diskette B. DVD-r flash drive C. flash drive D. random
access memory
20. What is the first step in data processing wherein data is pulled from available sources?
A. data collection B. data input C. data interpretation D. data input data
storage
21. If you are going to make a flowchart and you were told to use a symbol that shows
relationships between the representative shapes, what symbol do you need to use?
A. arrow B. action or process symbol C. decision symbol D. start/end
symbol
22. Which of the following symbols represent a single step ("add two cups of flour"), or an entire
subprocess ("make bread") within a larger process?
A. arrow B. action or process symbol C. decision symbol D. start/end symbol
23. What is being defined as a symbol to decide or branching point?
A. arrow B. action or process symbol C. decision symbol D. start/end symbol
24. Ms. Hanzel asked her student to make a flowchart, to begin this, what symbol her student
should use which is also used as the ending point of the system?
A. arrow B. action or process symbol C. decision symbol D. start/end
symbol
25. What is this being defined as a symbol that represents material or information entering or
leaving the system, such as customer order (input) or a product (output)?
A. action or process symbol C. input/output symbol
B. decision symbol D. start/end symbol
26. Which of the following represents the components of a process, device, or other object using
abstract, often standardized symbols and lines?
A. block diagram C. schematic diagram
B. causal loop diagram D. site layout plan
27. Flowchart is also known as ________________.
A. Casual loop diagram C. Flow diagram
B. Block diagram D. Schematic diagram
28. What is this diagram that shows a detailed layout of the whole site and the relationship of the
proposed works with the boundary of the property, nearby roads and neighboring buildings?
A. block diagram C. schematic diagram
B. causal loop diagram D. site layout plan
29. Aiza was assigned to make a diagram that shows a system in which the principal parts or
functions are represented by blocks connected by lines that show the relationships of the blocks.
What should Aiza do if this is the description given to her?
A. chart B. block diagram C. schematic diagram D. site layout plan
30. You want to budget your expenses for each month, that can be applied and shown to know
which is the most important to spend. Which of the following is defined as a graphical
representation of data, slices in a pie chart?
A. chart B. block diagram C. schematic diagram D. site layout plan
31. Which of the following devices is used for recording information?
A. Electronic Device C. Memory Module
B. Electronic Storage D. USB
32. What do you call a removable storage device that is corrected to the USB port?
A. Flash drive B. Floppy disk C. Memory card D. SATA
33. Roberto wants to show the sequence of how to make a "yummy burger". Which of the
following diagrams uses graphic symbols to depict the nature and flow of the steps in a process?
A. Flowchart B. Graph C. Picture D. Table
34. Which of the following symbols lines representing different decisions emerge from
different points, such as a decision or branching point.
A. B. C. D.
35. Which of the following symbols showed a decision point, such as start or end. What symbol is
this?

A. B. C. D.

II.
Directions: Write letter A if the statement is correct and letter B if the statement is wrong.

36. All tools and equipment must be properly maintained to avoid endangered.
37. Damage or defective equipment/tools should be tagged and removed from service.
38. Most manufacturers can provide maintenance schedules for their equipment.
39. Properly stored tools and equipment will not be easy to find when needed and are less
likely to be lost.
40. Productivity is decreased because time is not lost looking for tools, parts and equipment is
one of the benefits of proper storage.
41. Health and safety procedures are the responsibility of some person in the computer and
technology industries.
42. If you need to temporarily run a cable across the floor, place a Danger sign like those “wet
floor” signs used by cleaning services.
43. Your knees should be bent at a comfortable angle and greater than 90 degrees flexion
when sitting in front of a computer.
44. A well-designed mouse can cause undue pressure on the wrist and forearm muscles.
45. Set the eye to screen distance that permits you to focus on the screen most easily.
III. CONVERSION/COMPUTATION:
A. Directions: Convert the decimal numbers to binary digits. Show your solution.

46. 28 (A. 110011 B. 111011 C. 11100 D. 110111)

47. 43 (A. 101111 B. 101011 C. 111001 D. 101101)
48. 62 (A. 101101 B. 101101 C. 1101010 D. 111110)
49. 75 (A. 1001011 B. 1110101 C. 1110111 D. 1101111)
50. 25 (A. 11101 B. 1101 C. 11001 D. 101)

B. Direction: Convert the binary to decimal numbers. Show your solution.

51. 100100 (A. 36 B. 37 C. 39 D. 40)

52. 101100 (A. 43 B. 44 C. 45 D. 46)
53. 1101 (A. 12 B. 13 C. 14 D. 15)
54. 1001101 (A. 76 B. 77 C. 78 D. 79)
55. 11001 (A. 45 B. 25 C. 15 D. 20)

IV.
Direction: Give the correct abbreviations of the following unit. Write the letter of the correct
answer, use capital letters only.
56. Kilobyte (A. K B. KC C. KB D. MB)
57. Megabyte (A. MB B. KB C. K D. GB)
58. Gigabyte (A. MB B. KB C. K D. GB)
59. Terabyte (A. MB B. PB C. TB D. GB)
60. Petabyte (A. MB B. PB C. TB D. GB)

Prepared by: Checked by: Reviewed by: Noted by:

RODRIGO B. YUSON RACHEL ROSE A. VILLAFUERTE LUCENIA G. JUAYONG Ph. D. ANA MARIA G. RIVAS

RUBY O. BITANCOR TLE/TVL, Chairperson Master Teacher I, TVL/TLE SHS Principal

II

ANA J. BALASTA ALVIN E. FERIAS

 TLE 8 Teacher Master Teacher I, TVL/TLE JHS

ANSWER KEY:

1. C 32. A
2. A 33. A
3. B 34. D
4. C 35. B
5. B 36. A
6. A 37. A
7. C 38. A
8. B 39. B
9. D 40. B
10. D 41. B
11. A 42. A
12. A/C 43. A
13. B 44. B
14. B 45. A
15. A 46. C
16. A 47. B
17. C 48. D
18. C 49. A
19. D 50. C
20. A 51. A
21. A 52. B
22. B 53. B
23. C 54. B
24. D 55. B
25. C 56. C
26. C 57. A
27. C 58. D
28. D 59. C
29. B 60. B
30. A

31. B
 MAXIMO L. GATLABAYAN MEMORIAL NATIONAL HIGH SCHOOL
Sitio Paenaan Brgy. San J ose, Antipolo City
SECON QUARTERLY EXAMINATION
(T.L.E 8) COMPUTER SERVICING SERVICES
SY: 2023- 2024
Table of Specification
LEARNING COMPETENCIES EASY (60%) AVERAGE (30%) DIFFICULT(10%) NO. OF TESTITEMS
REMEMBERING UNDERSTANDING APPLYING ANALYZING EVALUATING CREATING
Classify use appropriate hand 6 4 10
tools and test equipment
Determine requirements of task in accordance with 4 4
the required output
Define hazard 1 1
Select appropriate hardware and software 4 1 5
according to task assigned and required outcome
Identify and interpret symbols used in the drawing 3 5 5 13
Identify tasks to be undertaken for proper storage of
instruments according to manufacturer’s 2 2
specifications and standard operating procedures
Convert decimal numbers to binary digits. 5 5
Convert binary digits to decimal numbers. 5 5
Distinguish the Plan a task to ensure that OSH 10 10
guidelines and procedures are followed
Identify units of memory 5 5
40 20 0 60
Prepared by: Checked by: Checked by:
RODRIGO B. YUSON RACHEL ROSE A. VILLAFUERTE LUCENIA G. JUAYONG Ph.D.
RUBY O. BITANCOR TLE/TVL Chairperson Master Teacher I, TLE/TVL SHS
ANA J. BALASTA ALVIN E. FERIAS
Region IV-A CALABARZON

TLE 8 Teacher Master Teacher I,TLE/TVL JHS

Republic of the Philippines
Department of Education
CITY SCHOOLS DIVISION OFFICE OF ANTIPOLO
MAXIMO L. GATLABAYAN MEMORIAL NATIONAL HIGH SCHOOL

Sitio Paenaan, San Jose, Antipolo City

Telephone No.: (02) 8425-1807