HOME ELECTRICAL › ELECTRONICS › COMMUNICATION › ROBOTICS PRO
Projects › Project Ideas IC › Embedded Sensors Components Tools ›
MC34063 DC to DC Converter : Pin
Configuration & Its Applications
An MC34063 DC to DC converter is also called a step-down or buck converter. This kind of
to decrease the voltage when the current is increased from its supply to load. Here the reg
voltage is lower as compared to the input voltage. There are different types of DC to DC co
available in the market like LM2596, LM2576D2TR4, R1SE0505R, TSRN12433, LM2678TA
A DC to DC converter is one kind of electromechanical device or an electronic circuit, used
source from one level of voltage to other. In this converter, the power levels mainly range fr
This article discusses MC34063 DC to DC Converter, pin configuration, working & its applic
What is MC34063 DC to DC Converter?
A buck converter IC like MC34063 is a DC voltage converter that converts the voltage from
level. These ICs are common elements in several applications like portable devices, satellit
systems, etc.
This MC34063A IC includes many functions which are mainly necessary for DC to DC conv
series was specially designed to use in different applications like a step up, step down & in
MC34063 DC to DC Converter
The main reason to use these converters in several applications is, they provide high efficie
operation, greater reliability, various voltage and current levels from a similar PCB design. T
kinds of DC to DC converters like a buck, boost, flyback, etc.
All these converters are also called switching regulators which are efficient highly like abov
evaluated to linear type regulators. While choosing a DC/DC converter, every designer mus
different factors like efficiency, the relation of I/O voltage, I/O isolation, highest o/p current,
voltage.
Pin Configuration
The pin configuration of the MC34063 DC to DC converter is shown below. This IC includes
each pin with its functionality is discussed below.
MC34063 IC Pin Configuration
Pin1 (Switch Collector): This is the collector pin of the transistor which is also known as a
Pin2 (Switch Emitter): This is an emitter pin of the transistor
Pin3 (Timing Capacitor): This pin is connected to a capacitor to decide the switching freq
Pin4 (Ground): This pin is connected to the GND pin
Pin5 (Inverting Input of Comparator): This pin is used to set the o/p voltage
Pin6 (Vcc): Input voltage is given to this pin
Pin7 (Ipeak Sense): This pin is used to set the o/p current
Pin8 (Driver Collector): This is the collector pin of the transistor
Features & Specifications
The features and specifications of the MC34063 DC to DC converter include the followin
Input voltage supply ranges from 3V – 40 V
Standby current is low
DC to DC converter chip
O/P voltage can be adjusted from 1.25volts to 40volts
The operating frequency is 100 kHz
Max capacity of current is 1.5A
Switching frequency is100KHz
Collector current is 100mA
The internal reference is 2%
These ICs are Halogen, BFR, Pb−Free & are compliant with RoHS
Alternative DC-DC converters are LM2596, UCC25600, TC7660, and MCP16252 & Equiva
DC to DC converters are CS51411, ACT4514, and TS2580.
Switching Regulator Circuit using MC34063 DC to DC Converter
The circuit diagram of the switching regulator with MC34063A DC to DC converter is show
This circuit operates with a 12V stable battery. Even though, the input voltage can be chan
This circuit has maximum efficiency above 90% and this can be built with some basic elec
components very easily with less cost. This circuit can be built with an MC34063 dc to dc
variable resistor like VR1 to control efficiency.
Switching Regulator Circuit with MC34063 IC
This IC is extremely helpful, so it can be used like different DC to DC converters like step-up
inverter including the functions of step-up/step-down. This IC is used in different devices li
chargers.
Circuit Working
The above circuit uses basic electronic components. In the circuit, the IC is powered by pro
pin 6 like VCC & pin-4 to the GND terminal. A 100uF capacitor is used in this circuit to filter
from the power supply.
The Pin-2 of IC is connected to the base terminal of the transistor in the circuit like TIP31 t
circuit, pin-3 is connected to the timing capacitor like C2 & it will decide the circuit’s switch
pin-5 is an inverting terminal for the comparator
The non-inverting terminal’s voltage is from the interior voltage regulator is 1.25V. A resisto
placed at the inverting terminal of the comparator. The gain of the comparator can be deci
formula like VOUT = 1.25V * (1 + (R4/R3)). A potentiometer like VR1 is used for regulating t
12V 600mA.
In this way, the above circuit has the boost functionality and this is a typical SMPS with the
operate like a boost converter or step-up converter.
Where to use MC34063A/Applications
Generally, the IC like MC34063A DC-DC converter is used to design step down or Buck, ste
inverter circuits. This IC is an industry-standard, used to change the voltage in phone charg
automobiles.
Since the regulation takes place throughout switching then it is extremely efficient as com
circuits. So if you are looking to design a DC to DC converter with the above-mentioned spe
an MC34063 dc to dc converter is best.
The MC34063 IC was mainly designed to integrate into different converter-based applicati
buck otherwise voltage-inverter. It is used in the applications like portable chargers, circuits
battery, medical devices, consumer electronics & measurement devices.
Thus, this is all about an overview of the MC34063 DC to DC Converter datasheet which in
configuration, features, specifications, circuit, and applications. Generally, this DC to DC co
of electronic circuit, used to step down/up the voltage to obtain the preferred voltage. This
in automobiles, solar grids, adaptors of laptops, etc. Here is a question for you, what is a bo
SHARE THIS POST:
Facebook Twitter Google+ LinkedIn Pinterest
‹ PREVIOUS
TIP31C NPN Transistor : Pin C
BC337 Transistor : Pin Configuration & Its
I
Applications
RELATED CONTENT
Molded Case Circuit Breaker Magnetic Starter : Circuit, Preamplifier : Circuit, Working, 2 Point St
(MCCB): Types, Working, and Working, Wiring, Vs Contactor, Types, Differences, How to Difference
Applications Explained Advantages & Its Applications Choose, & Its Applications
CATEGORIES RECENT COMMENTS
Communication K BALAJI on Simple Electronic Circuits for
Beginners
Electrical
Anny Arbert on Gyroscope Sensor Working
Electronics
and Its Applications
Project Ideas
Abhuday dangi on What is a UJT Relaxation
Robotics Oscillator – Circuit Diagram and Applications
Technology Satyadeo Vyas on Construction and
Working of a 4 Point Starter
Advertise With Us Disclaimer Report Violation Image Usage
Copyright 2013 - 2025 © Elprocus
