XL 5320 V MINE SCALING MACHINE

XL 5320 V
MINE SCALING MACHINE

SPECIFICATIONS
• Tilting/telescoping steering column Three Hydraulic Motors
Engine • Hydraulic foot pedal controls braking • Swing, 68 hp (38 kW)
functions • Tilt, 50 hp (37 kW)
• Volvo TAD571 VE, Tier 4f, 4 cycle, inline 4
cylinder, liquid cooled, electronic controlled • Travel speed is regulated with an • Propel, 113 hp (84 kW)
electronic foot pedal control
• Vertical canister style lube and main fuel Operating Pressures:
filters and fuel/water separation with • Switch on the FWD/REV selector
provides 1st/2nd gear selection • Hoist......................... 4,900 psi (331 BAR)
manual feed pump attached to engine • Tilt............................ 4,900 psi (331 BAR)
• Independent rocker switches control
• Water in fuel indicator and alarm • Swing....................... 4,500 psi (310 BAR)
stabilizers, axle oscillation, park brake,
Gross Rating: 173 hp @ 2200 rpm (129kW) and hazard lights • Tool.......................... 4,900 psi (331 BAR)
590 ft lb Torque @ 1100- • Telescope............... 4,900 psi (331 BAR)
Engine Controls and Instrumentation
1500 rpm (800Nm) • Propel....................... 4,900 psi (331 BAR)
• Key operated ignition/starter switch,
Net Rating: 153 hp @ 2200 rpm (114kW) throttle, and main battery disconnect switch • Pilot System............... 550 psi (38 BAR)
• Variable viscous fan clutch system • Air cleaner condition indicator • Braking & Steering... 2,400 psi (165 BAR)
• Vertical stacked hydraulic oil cooler, • Electronic monitor indicates fuel level, low • Blade & Stabilizers.. 4,000 psi (207 BAR)
charge air cooler and radiator battery charge, lube oil pressure, high Oil Capacity
coolant temperature, engine rpm, and
Maximum slope: 30° • Reservoir system 65 gallons (246 L)
engine hours
• 24 volt starter • Pressurized reservoir with visual oil level
• Fuel saving auto idle feature sends
• 100 amp alternator gauges
engine rpm to idle when control circuits
• Two SAE #C31-S 1000 CCA batteries are in neutral for seven seconds. Filtration System
• Two-stage dry type air cleaner with • 10 micron return filter
centrifugal pre-cleaner and safety element Boom • 10 micron pilot filter
• Vacuator valve and service indicator • Fin and tube-type oil cooler with thermal
• Two piece triangular telescoping boom
by-pass and relief valves
Fuel tank capacity: 99 gallons (375 L) • Adjustable boom rollers with eccentric shafts • Pressure-compensated, load-sensing
• 220° boom tilt valves with circuit reliefs in all circuits
Operator Cab • 105° boom pivot angle
• All-weather cab Undercarriage
• Tinted safety glass windows Hydraulic System
• Both axles are equipped with internal
• Acoustical lining Pump wet-disc type service brakes
• Four-way adjustable seat • One load-sensing, axial piston pump; oil • Steering axle is fitted with oscillation lock
• AM/FM radio flow 0-110 gpm (0-435 L/min) cylinders
• Filtered fresh air heater • Tandem gear pump (steering, brake/pilot) Tires: 1
 0 x 20 Super-Lug
• Defroster 10 GPM (38 L/min), 6 GPM (23 L/min)
Axles: ZF Model 3070 (FTF 2090)
• Air conditioning System monitor
• Front window has heat resistant glass Transmission: ZF Model HL 290
• Electronic monitor in cab indicates
• Rearview mirrors on right and left sides - Low hydraulic fluid level, with shutdown Drive Motor: Rexroth A6 Series, 160cc/Rev
• Seat belt - High hydraulic fluid temperature Minimum Turning Radius: 25’5” (7.75 m)
• Swing lights - System working pressure • Variable displacement high torque piston
- System pilot pressure motor powers the two-speed power shift
Controls transmission
SYSTEM SPECIFICATIONS • Speed mode selection can also be done
• Two electronic joysticks (hoist and Six Cylinders while moving
bucket, telescope and swing) • One tool: 5.0” ID, 3.0” rod • Electronically operated travel alarm
• One rocker switch (tilt) control (127 mm x 76 mm), 25.9” (658 mm) stroke signals excavator movement
• Joysticks mounted on arm pods • Two hoist: 4.75” ID, 3.35” rod Travel speed on flat surface - MPH (kmh):
• Quick change joystick pattern switch (121 mm x 85 mm), 31.0” (787 mm) stroke
located on instrument panel • One telescope: 3.75” ID, 2.75” rod Creeper Mode Standard Mode

• Joysticks are self-centering; when controls (95 mm x 70 mm), 14’ (4.27 m) stroke First Gear 1.8 mph (2.9 kmh) 5.7 mph (9.2 kmh)
are released, power for movement • Two single-acting axle oscillation
disengages and swing and tilt brake set Second Gear 6.3 mph (10.1 kmh) 12 mph (19.3 kmh)
cylinders: 4.528” ID, 4.528” rod (115 mm
automatically x 115 mm), 6.25” (159 mm) stroke
 Dimensions
A Overall length with attachment open J4 Nominal overall length of undercarriage: 12’3” (3.7) AH Minimum radius at groundline: 14’4” (4.4)
(Travel Position): 28’4” (8.6) J5 Axis of rotation to front option attachment pin: 6’9” (2.1) AK Boom pivot to groundline: 6’5” (2.0)
A1 Overall length without attachment J6 Axis of rotation to rear option attachment pin: 4’9” (1.4) AL Boom pivot to axis of rotation: 1’11” (585 mm)
(Travel Position): 26’3” (8.0)
J7 Outrigger length, attachment pin to pad in up AP Attachment tooth radius (scaling hook): 3’10”
B Overall height with attachment open position: 2’7” (0.8) (1.2)
(Travel Position): 11’6” (3.5)
J8 Outrigger length, attachment pin to pad in down Attachment bit radius (S-29 Hammer): 7’0” (2.1)
B1 Overall height without attachment position: 3’3” (1.0)
(Travel Position): 11’2” (3.4) AQ Boom pivot angle: 30° Up and 75° Down
J9 Blade length, attachment pin across blade in up AS Attachment pivot angle: 165°
C1 Width of upperstructure: 9’0” (2.7) position: 3’4” (1.0)
D Minimum clearance, upperstructure to AU Maximum telescoping boom length
K Overall width of undercarriage: 9’1” (2.8) (boom pivot to attachment pivot): 29’6” (9.0)
undercarriage: 3” (78 mm)
K1 Overall width outrigger (up position): 8’4” (2.5) AV Minimum telescoping boom length
E Swing clearance, rear of upperstructure: 8’6” (2.6)
K2 Overall width blade: 9’0” (2.7) (boom pivot to attachment pivot): 15’6” (4.7)
F Top of cab guard to groundline: 11’1” (3.4)
L Overall width outrigger (down position): 10’8” (3.3) AW Telescoping boom travel: 14’0” (4.3)
G Clearance, upperstructure to groundline: 4’2” (1.3)
N Ground clearance (per SAE J1234): 11” (275 mm) AX Attachment tilt angle (continuous): 360°
H1 Height of optional folding lift yoke lowered: 1’9” (0.5)
N1 Ground clearance (outrigger option): 12” (300 mm) BA Maximum radius of working equipment: 35’4” (10.8)
H2 Height of pin of optional folding lift yoke: 3’7” (1.1)
Z Blade above ground (option): 1’8” (505 mm) BB Maximum height of working equipment: 26’9” (8.2)
H3 Overall height of optional folding lift yoke: 4’0” (1.2)
Z1 Maximum lift of blade (option): 7’0” (166 mm) BD Minimum clearance of attachment with pivot at
H4 Height to pin of optional rigid lift yoke: 2’8” (0.8) maximum height: 19’2” (5.8)
Z2 Maximum lift of outrigger (option): 6’0” (142 mm)
H5 Overall height of optional rigid lift yoke: 3’0” (0.9) BF Minimum clearance of attachment at maximum
AA Maximum radius at groundline (Scaling Hook):
A xis of rotation to centerline of drive sprockets:
J1  34’9” (10.6) boom height: 12’2” (3.7)
3’6” (1.1) BG Maximum height of working equipment with
Maximum radius at groundline (S-29 Hammer):
J2 Wheelbase of undercarriage: 8’9” (2.7) 37’11” (11.6) attachment below groundline: 14’11” (4.5)
J3 Axis of rotation to front of undercarriage: 7’0” (2.1) AB Maximum depth: 25’5” (7.7) BH R
 adius of attachment tooth at maximum height:
27’1” (8.2)
Specifications subject to change without notice.
Metric units are meters (m) unless noted.
Machines shown may have optional equipment.

Swing Function Forces

It is Gradall Policy to continually improve its products. • Priority swing circuit with axial piston motor Rated Boom Force: 24,941 lbs (111 kN)
Therefore designs, materials and specifications are • Planetary transmission Rated Ripper Tooth Force: 25,405 lbs (113 kN)
subject to change without notice and without incurring
any liability on units already sold. Units shown may Swing speed: 7.0 rpm Boom Rotating Torque: 25,800 ft lb (34,980 Nm)
have optional equipment. Swing Brake Boom Rotating Speed: 7.0 rpm
• Automatic spring-set/hydraulic release
wet-disc parking brake Weight
• Dynamic braking is provided by the
406 Mill Ave. SW, New Philadelphia, Ohio 44663 hydraulic system • Approximate working weight with 36”
Phone: 800-445-4752 (914 mm) excavating bucket, fuel tank half
www.Gradall.com full
- 55,926 lbs (25,368 kg)
Outriggers: 2,720 lbs (1,234 kg)
Form No. 11833 12/22
Printed in USA Blade: 1,529 lbs (694 kg)