https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by sales@ChinaStandards.

net

ICS 21.100.20
J 11

National Standard of the People’s Republic of China

GB/T 3882-2017
Replaces GB/T 3882-1995

Rolling bearings—Insert bearings and

eccentric looking collars—
Boundary dimensions
滚动轴承 外球面球轴承和偏心套外形尺寸

(ISO 9628: 2006, Rolling bearings—Insert bearings and eccentric looking collars—
Boundary dimensions and tolerances, NEQ)

(English Translation)

Issue date: 2017-05-12 Implementation date: 2017-12-01

Issued by the General Administration of Quality Supervision,
Inspection and Quarantine of the People’s Republic of China
the Standardization Administration of the People’s Republic
of China

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Contents

Foreword...........................................................................................................................................i
1 Scope ......................................................................................................................................... 1
2 Normative references .............................................................................................................. 1
3 Terms and definitions ............................................................................................................... 1
4 Symbols ..................................................................................................................................... 1
5 Characteristics .......................................................................................................................... 6
6 Code ........................................................................................................................................... 7
7 Designation example ............................................................................................................... 8
8 Boundary dimension ................................................................................................................ 8

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Foreword

ChinaStandards.net is in charge of this English translation. In case of any doubt about

the English translation, the Chinese original shall be considered authoritative.

This standard is developed in accordance with the rules given in GB/T 1.1-2009.

This standard replaces GB/T 3882-1995 Rolling bearings—Insert bearings and eccentric
looking collars—Boundary dimensions and the following main technical changes have
been made with respect to GB/T 3882-1995:

——Some normative references are added and modified (see clause 2 hereof; clause 2 of
Edition 1995);

——The definition of “insert bearing” is modified (see clause 3 hereof; clause 3 of Edition
1995);

——The font and part of description of the symbol are modified (see clause 4 hereof;
clause 4 of Edition 1995);

——The description of the characteristics of insert bearings is modified (see clause 5

hereof, clause 5 of Edition 1995);

——The clauses of “code” and “Designation example” are added (see clauses 6 and 7
hereof);

——The models and boundary dimensions of insert bearings of inch bore diameter and
eccentric locking collars are added (see Tables 1-11);

——The size range of insert bearings with eccentric locking collars is expanded and some
boundary dimensions are modified (see Tables 1-3 hereof, Tables 6-8 of Edition 1995);

——Some boundary dimensions of insert bearings with jackscrew are modified (see
Tables 4-6 hereof, Tables 1-3 of Edition 1995);

——Some boundary dimensions of insert bearing with tapered hole and adapter sleeve
are modified (see Tables 7-8 hereof, Tables 4-5 of Edition 1995);

——The size range of inner ring eccentric extension is expanded and some boundary
dimensions are modified (see Table 9 hereof, Table 9 of Edition 1995);

——The size range of eccentric locking collars is expanded and some boundary
dimensions are modified (see Tables 10-11 hereof, Tables 10-11 of Edition 1995);

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

——Dimensions of lubrication zone of insert bearings are modified (see Tables 1-8 hereof,
Tables 1-8 of Edition 1995).

This standard is redrafted by reference to, but is not equivalent to ISO 9628: 2006 Rolling
bearings-Insert bearings and eccentric looking collars-Boundary dimensions and
tolerance and ISO 9628: 2006/Amd.1: 2011: Diameter series.

This standard was proposed by the China Machinery Industry Federation.

This standard is under the jurisdiction of the National Technical Committee on Rolling
Bearing of Standardization Administration of China (SAT/TC 98).

The previous editions of this standard are as follows:

——GB 3882.1~3882.3-1983;

——GB 3882-1987, GB/T3882-1995.

ii

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Rolling bearings—Insert bearings and eccentric

looking collars—
Boundary dimensions

1 Scope

This standard specifies the characteristics and boundary dimensions of insert bearings
(bearings for short) and eccentric locking collars.

This standard is applicable to the design and selection of bearings.

2 Normative references

The following referenced documents are indispensable for the application of this
document. For dated references, only the edition cited applies. For undated references,
the latest edition (including any amendments) applies.

GB/T 273.3 Rolling bearings—Boundary dimensions, general plan—

Part 3: Radial bearings
GB/T 4199 Rolling bearings—Tolerances—Definitions
GB/T 6930 Rolling bearings—Vocabulary
GB/T 7811 Rolling bearings—Symbols for physical quantities
GB/T 27554 Rolling bearings—Insert bearing units—Identification code

3 Terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 4199, and GB
6930 and the following apply.

3.1
insert bearing
radial rolling bearing with a spherical outside surface and an extended inner ring with a
locking device

Note: The locking device, used for fixing the inner ring to the shaft, may be an eccentric locking collar or
an adapter sleeve or jackscrew directly in the inner ring.

4 Symbols

For the purposes of this document, the symbols given in GB/T 7811 and the following
apply.

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

The symbols (except those for tolerances) shown in Figures 1 to 8 and the values given in
Tables 1 to 11 denote nominal dimensions unless specified otherwise.

Note: Figures 1 to 8 are drawn schematically and cages are not shown.

A: width of eccentric surface of inner ring

A1: width of eccentric surface of eccentric locking collar

B: width of inner ring

B1: overall width of inner ring including eccentric locking collar

B2: width of eccentric locking collar

B3: width of adapter sleeve

C: width of outer ring

C1: distance from centre of outer ring to centre of lubrication zone

C2: width of lubrication zone

D: outside diameter of bearing

d: bore diameter of bearing and of eccentric locking collar

ds: jackscrew diameter

dz: small bore diameter of inner ring taper hole

d0: bore diameter of adapter sleeve

d1: outside diameter of eccentric locking collar

d2: small bore diameter of eccentric surface (at theoretical sharp corner) of eccentric
locking collar

d3: large diameter of eccentric surface (at theoretical sharp corner) of inner ring

H: eccentricity of inner ring eccentric extension and of eccentric locking collar

r1: chamfer dimension of eccentric surface of inner ring

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

r1smin: smallest single chamfer dimension of eccentric surface of inner ring

r2: fillet radius of eccentric surface of inner ring

r2smax: largest single fillet radius of eccentric surface of inner ring

r3: fillet radius of eccentric surface of eccentric locking collar

r3smax: largest single fillet radius of eccentric surface of eccentric locking collar

r4: chamfer dimension of eccentric surface of eccentric locking collar

rr4smin: smallest single chamfer dimension of eccentric surface of eccentric locking collar

S: distance from centre of raceway to face of inner ring on side opposite locking device

S1: distance from centre of raceway to face of inner ring or eccentric locking collar limiting
overall bearing width on locking device side

Figure 1 Insert bearings with eccentric locking collar (UEL)

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Figure 2 Light insert bearings with eccentric sleeve (UE)

Figure 3 Insert bearings with jackscrew (UC)

Figure 4 Insert bearings with flat-end jackscrew (UB)

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Figure 5 Insert bearings with tapered bore (UK)

Figure 6 Insert bearings with adapter sleeve (UK + H)

Figure 7 Eccentric extension of inner ring

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Note: The relative angular position of the plain and tapped holes to each other and to the eccentricity is
optional.
Figure 8 Eccentric locking collars

5 Characteristics

5.1 General

The bearings on one shaft are, as a rule, mounted in two or more separate housings,
which are not always perfectly aligned. The outer ring has a spherical outside surface so
that the bearing can be mounted in a housing with a matching spherical seating to
accommodate permanent angular misalignment.

The bearing ring and the eccentric locking collar may be treated with a surface treatment
to reduce corrosion during operation.

5.2 Bore diameter

For each bearing or eccentric locking collar, it is generally common to have one metric and
several inch inner ring bore sizes. The non-preferred inch bore sizes, which are given in
parentheses in Tables 1,3,4 shall be avoided whenever possible.

Contrary to general rolling bearing practice, the inner ring bore diameter tolerance is on
the plus side of the nominal bore diameter, in order that the bearing and collar can be
slipped over standard size shafting.

5.3 Outside diameter of bearing

The outside diameter (with respect to metric bore diameter, taking 40 mm except those
less than 40 mm) of the bearing of series 2 and 3 corresponds to the diameter series 2
and 3 of GB/T 273.3 respectively.

5.4 Width of inner ring and locking device

https://www.chinastandards.net/standard/GBT3882-2017.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

The inner ring width (with respect to the metric bore diameter) does not conform to the
requirements of dimension series 2 and 3 of GB/T 273.3. It is determined by the
requirements of space for sealing and locking devices and by the axial extension of the
shaft support considered suitable for various applications.

Where the locking device extends axially beyond the inner ring, the width over the locking
device, called the overall width, and the location with respect to the outer ring centreline of
the side face limiting the overall width, are important dimensions. Each of Figures 1 to 6
shows one example only of locking device design.

5.5 Width of outer ring

For bearings with a spherical outside surface, the width of the outer ring is not important,
provided the range of width is known so that assembly slots in the housing can be
properly dimensioned. This standard therefore gives outer ring widths which range from a
minimum that conforms to dimension series 2 and 3 in GB/T 273.3, to a maximum that
provides sufficient space for various seals and relubrication holes.

5.6 Relubrication

Depending on the application, these bearings are supplied with or without means for
relubrication, for example, one or more small radial holes drilled through the outer ring.
The exact design and location of such means are not specified in this standard. Given
only is the width and location of a zone in which any relubrication means, provided on one
or both sides of the outer ring, shall intersect in such a way that lubricant will satisfactorily
feed into the bearing from the housing bore groove covering the zone.

6 Code

6.1 The insert bearings with metric bore diameter shall be designated in accordance
with GB/T 27554.

6.2 The construction type of eccentric locking collars with metric bore diameter is
indicated by the capital Latin letter E, with its dimension series and bore diameter codes
consistent with those of insert bearings.

6.3 The insert bearing and eccentric locking collars of inch bore diameter are the codes
for insert bearings and eccentric locking collars of metric bore diameter plus the codes for
inch bore diameter.

Inch bore diameter code is expressed by the number of millimeters of the bore diameter
divided by 25.4 and multiplied by an integer of 16.

Example: UEL 201-8

https://www.chinastandards.net/standard/GBT3882-2017.html