D-1

CHAPTER D DESIGN OF MEMBERS FOR TENSION

Section D1 does not establish a slenderness limit for tension members, but recommends limiting L/r to a maximum of 300. This is not an absolute requirement, and rods and hangers are specifically excluded from this recommendation. D2. TENSILE STRENGTH

Both tensile yield strength and tensile rupture strengths must be considered for the design of tension members. It is not unusual for tensile rupture strength to govern the design of a tension member, particularly for small members with holes or heavier sections with multiple rows of holes. For preliminary design, tables are provided in Part 5 of the Manual for W-shapes, L-shapes, WT shapes, Rectangular HSS, Square HSS, Round HSS, Pipe and 2L-shapes. The calculations in these tables for available tensile rupture strength assume an effective area, Ae, of 0.75Ag. If the actual effective area is greater than 0.75Ag, the tabulated values will be conservative and manual calculations can be performed to obtain higher available strengths. If the actual effective area is less than 0.75Ag, the tabulated values will be unconservative and manual calculations are necessary to determine the available strength. D3. AREA DETERMINATION

The gross area, Ag, is the total cross-sectional area of the member. In computing net area, An, an extra z in. is added to the bolt hole diameter and an allowance of z in. is added to the width of slots in HSS gusset connections. A computation of the effective area for a chain of holes is presented in Example D.9. Unless all elements of the cross-section are connected, Ae=AnU, where U is a reduction factor to account for shear lag. The appropriate values of U can be obtained from Table D3.1 of the Specification. D4. BUILT-UP MEMBERS

The limitations for connections of built-up members are discussed in Section D4 of the Specification. D5. PIN-CONNECTION MEMBERS

An example of a pin-connected member is given in Example D.7. D6. EYEBARS

An example of an eyebar connection is given in Example D.8.

D-2

Example D.1
Given:

W-Shape Tension Member

Select an 8 in. W-shape, ASTM A992, to carry a dead load of 30 kips and a live load of 90 kips in tension. The member is 25 ft long. Verify the member strength by both LRFD and ASD with the bolted end connection shown. Verify that the member satisfies the recommended slenderness limit.

Solution: Calculate the required tensile strength

Pu = 1.2(30 kips) + 1.6(90 kips) = 180 kips Try a W821 Material Properties: W821 ASTM A992

Pa = 30 kips + 90 kips = 120 kips

Fy = 50 ksi

Fu = 65 ksi tf = 0.400 in. d = 8.28 in.

Manual Table 2-3 Manual Table 1-1 Table 1-8

Geometric Properties: bf = 5.27 in. W821 Ag = 6.16 in.2 ry = 1.26 in. y = 0.831 in. (for WT410.5)

Check tensile yield limit state using tabulated values

277 kips > 180 kips

o.k.

184 kips > 120 kips

o.k.

Manual Table 5-1

Check the available tensile rupture strength at the end connection Verify the table assumption that Ae / Ag 0.75 for this connection

D-3

Calculate U as the larger of the values from Table D3.1 case 2 or case 7 Case 2 Check as 2 WT-shapes U = 1 Case 7 bf = 5.27 in. d = 8.28 in. bf < 2/3d U = 0.85 Use U = 0.908 Calculate An An = Ag 4(dh + z in.)tf = 6.16 in.2 4(m in. + z in.)(0.400 in.) = 4.76 in.2 Calculate Ae Ae = AnU = 4.76 in.2(0.908) = 4.32 in.2 Ae /Ag = 4.32 in. / 6.16 in. = 0.701 < 0.75 tabulated values for rupture n.a. Pn = FuAe = (65 ksi)(4.32 in.2) = 281 kips Eqn. D2-2
LRFD ASD
2 2

Commentary Fig. C-D3.1

x l

= 1

0.831 in. = 0.908 9.00 in.

Table D3.1 Case 2

Table D3.1 Case 7

Section D3.2

Section D3.3 Eqn. D3-1

t = 0.75 tPn = 0.75(281 kips) = 211 kips 211 kips > 180 kips
o.k.

t = 2.00 Pn/t = (281 kips)/2.00 = 141 kips 141 kips > 120 kips
o.k.

Section D2

Check the non-mandatory slenderness limit

Section D1

o.k.
ASD

225 kips > 180 kips

o.k.

150 kips > 120 kips

o.k.

Manual Table 5-1

The W821 available tensile strength is governed by the tensile rupture limit state at the end connection.

D-4

Example D.2
Given:

Single-Angle Tension Member

Verify, by both ASD and LRFD, the strength of an L44, ASTM A36, with one line of (4) in. diameter bolts in standard holes. The member carries a dead load of 20 kips and a live load of 60 kips in tension. Calculate at what length this tension member would cease to satisfy the recommended slenderness limit.

Solution: Material Properties: L44 ASTM A36 Geometric Properties: L44 Ag = 3.75 in.2
LRFD

Fy = 36 ksi rz = 0.776 in.

Fu = 58 ksi
y = 1.18 in. = x
ASD

Manual Table 2-3 Manual Table 1-7

Calculate the required tensile strength Pu = 1.2(20 kips) + 1.6(60 kips) = 120 kips Calculate the available tensile yield strength Pn = FyAg = (36ksi)(3.75in.2) = 135 kips
LRFD ASD

Pa = 20 kips + 60 kips = 80.0 kips

Eqn. D2-1 t = 1.67 Pn /t = (135 kips)/1.67 = 80.8 kips

t = 0.90 tPn = 0.90(135 kips) = 122 kips

Section D2

Calculate the available tensile rupture strength Calculate U as the larger of the values from Table D3.1 case 2 or case 8 Case 2
1.18 in. x = 1 = 0.869 9.00 in. l Case 8 with 4 or more fasteners per line in the direction of loading

U = 1

Table D3.1 Case 2

U = 0.80 Use U = 0.869

Table D3.1 Case 8

D-5

Calculate An An = Ag (dh + z)t = 3.75 in.2 (m in. + z in.)(2 in.) = 3.31 in.2 Calculate Ae Ae = AnU = 3.31 in.2(0.869) = 2.88 in.2 Pn = FuAe = (58 ksi)(2.88 in.2) = 167 kips
LRFD ASD

Section D3.2

Section D3.3 Eqn. D3-1 Eqn. D2-2 t = 2.00 Pn/t = (167 kips)/2.00 = 83.5 kips

t = 0.75 tPn = 0.75(167 kips) = 125 kips

Section D2

The L442 available tensile strength is governed by the tensile yielding limit state.
LRFD ASD

tPn = 125 kips 125 kips > 120 kips

o.k.

Pn/t = 83.5kips 83.5 kips > 80.0 kips

o.k.

Calculate recommended Lmax

Section D1

Note: The L/r limit is a recommendation, not a requirement.

D-6

Example D.3
Given:

WT-Shape Tension Member

A WT620, ASTM A992, member has a length of 30 ft and carries a dead load of 40 kips and a live load of 120 kips in tension. Assume the end connection is fillet welded and has a length of 16 in. Verify the member strength by both LRFD and ASD. Assume that the gusset plate and the weld have been checked and are satisfactory.

Solution: Material Properties: WT620 ASTM A992 Geometric Properties: WT620 Ag = 5.84 in.2

Fy = 50 ksi rx = 1.57 in.

Fu = 65 ksi
y = 1.09 in. = x (in equation for U)

Manual Table 2-3 Manual Table 1-8

Calculate the required tensile strength

Pu = 1.2(40.0 kips) + 1.6(120 kips) = 240 kips

Pa = 40.0 kips + 120 kips = 160 kips

Check tensile yielding limit state using tabulated values

tPn = 263 kips > 240 kips

o.k.

Pn/t = 175 kips > 160 kips

o.k.

Manual Table 5-3

Check tensile rupture limit state using tabulated values

214 kips < 240 kips

n.g.

142 kips < 160 kips

n.g.

Manual Table 5-3

The tabulated available rupture strengths may be conservative for this case, therefore calculate the exact solution. Calculate U x 1.09 in. U = 1 = 1 = 0.932 l 16.0 in.

Table D3.1 Case 2

D-7

Calculate An An = Ag = 5.84 in.2 (because there are no holes) Calculate Ae Ae = AnU = 5.84 in.2(0.932) = 5.44 in.2 Calculate Pn Pn = Fu Ae = 65 ksi(5.44 in2) = 354 kips
LRFD ASD

Section D3.2

Section D3.3 Eqn. D3-1

t = 0.75 tPn = 0.75(354 kips) = 266 kips 266 kips > 240 kips
o.k.

t = 2.00 Pn/t = (354 kips)/2.00 = 177 kips 177 kips > 160 kips
o.k.

Section D2

Alternately, the available tensile rupture strengths can be determined by modifying the tabulated values. The available tensile rupture strengths published in the tension member selection tables are based on the assumption that Ae = 0.75Ag. The actual available strengths can be determined by adjusting the table values as follows:
LRFD ASD

Ae tPn = 214 kips 0.75 A g 5.44 in.2 = 214 kips 0.75 5.84 in.2

= 266 kips

Ae Pn/t = 142 kips 0.75 A g 5.44 in.2 = 142 kips 0.75 5.84 in.2

Manual Table 5-3

= 176 kips

The WT620 available tensile strength is governed by the tensile yielding limit state.
LRFD ASD

tPn = 263 kips 263 kips > 240 kips

o.k.

Pn/t = 175 kips 175 kips > 160 kips

o.k.

Check the non-mandatory slenderness limit

Section D1
o.k.

D-8

Example D.4
Given:

Rectangular HSS Tension Member

Verify, by LRFD and ASD, the strength of an HSS64a, ASTM A500 grade B, with a length of 30 ft. The member is carrying a dead load of 35 kips and a live load of 105 kips in tension. Assume the end connection is fillet welded to a 2 in. thick single concentric gusset plate and has a length of 16 in.

Solution: Material Properties: HSS64a ASTM A500 grade B Member Geometric Properties: HSS64a Ag = 6.18 in.2

Fy = 46 ksi ry = 1.55 in.

Fu = 58 ksi t = 0.349 in.

Manual Table 2-3 Manual Table 1-11

Calculate the required tensile strength

Pu = 1.2(35.0 kips) + 1.6(105 kips) = 210 kips Check available tensile yield strength
LRFD

Pa = 35.0 kips + 105 kips = 140 kips

ASD

tPn = 256 kips > 210 kips Check available tensile rupture strength
LRFD

o.k.

Pn/t = 170 kips > 140 kips

o.k.

Manual Table 5-4

ASD

201 kips < 210 kips

n.g.

134 kips < 140 kips

n.g.

Manual Table 5-4

The tabulated available rupture strengths may be conservative in this case, therefore calculate the exact solution. Calculate U (4.00 in.)2 + 2(4.00 in.)(6.00 in.) B 2 + 2 BH x = = = 1.60 in. 4( B + H ) 4(4.00 in. + 6.00 in.) U = 1
x 1.60 in. = 1 = 0.900 16.0 in. l

Table D3.1 Case 6

D-9

Allowing for a z in. gap in fit-up between the HSS and the gusset plate, An = Ag 2(tp + z in.)t = 6.18 in.2 2(2 in. + z in.)(0.349 in.) = 5.79 in.2 Calculate Ae Ae = AnU = 5.79 in.2(0.900) = 5.21 in.2 Calculate Pn Pn = Fu Ae = 58 ksi(5.21 in2) = 302 kips
LRFD ASD

Section D3.2

Section D3.3 Eqn. D3-1

t = 0.75 tPn = 0.75(302 kips) = 227 kips 227 kips > 210 kips
o.k.

t = 2.00 Pn /t = (302 kips)/2.00 = 151 kips 151 kips > 140 kips
o.k.

Section D2

The HSS available tensile strength is governed by the tensile rupture limit state. Check the non-mandatory slenderness limit
30.0 ft 12.0 in. L/r = = 232 < 300 1.55 in. ft

Section D1
o.k.

D-10

Example D.5
Given:

Round HSS Tension Member

See Figure D-5 below. An HSS6.0000.500, ASTM A500 grade B, has a length of 30 ft. The member carries a dead load of 40 kips and a live load of 120 kips in tension. Assume the end connection is a fillet welded 2 in. thick single concentric gusset plate that has a length of 16 in. Verify the strength by both LRFD and ASD.

Solution: Material Properties: HSS6.0000.500 ASTM A500 grade B Member Geometric Properties: HSS6.0000.500 Ag = 8.09 in.2

Fy = 42 ksi r = 1.96 in.

Fu = 58 ksi t = 0.465 in.

Manual Table 2-3 Manual Table 1-13

Calculate the required tensile strength

Pu = 1.2(40.0 kips) + 1.6(120 kips) = 240 kips Check available tensile yield strength
LRFD

Pa = 40.0 kips + 120 kips = 160 kips

ASD

tPn = 306 kips > 240

o.k.

Pn/t = 203 kips > 160 kips

o.k.

Manual Table 5-6

Check available tensile rupture strength

tPn = 264 kips > 240 kips

o.k.

Pn/t = 176 kips > 160 kips

o.k.

Manual Table 5-6

Check that Ae 0.75 Ag as assumed in table L = 16.0 in. U = 1.0 Allowing for a z in. gap in fit-up between the HSS and the gusset plate, An = Ag 2(tp + z in.)t = 8.09 in.2 2(0.500 in. + z in.)(0.465 in.) = 7.57 in.2 Section D3.2 D = 6.00 in. L/D = 16.0 in./(6.00 in.) = 2.67 > 1.3 Manual Table D3.1 Case 5

D-11

Calculate Ae Ae = AnU = 7.57 in.2 (1.0) = 7.57 in.2 Ae /Ag = 7.57 in.2 /(8.09 in.2) = 0.936 in.2 > 0.75 Ag Check the non-mandatory slenderness limit
30.0 ft 12.0 in. L/r = = 184 < 300 1.96 in. ft

Section D3.3 Eqn. D3-1

o.k.

Section D1
o.k.

D-12

Example D.6
Given:

Double-Angle Tension Member

A 2L442 (a-in. separation), ASTM A36, has one line of (8) -in. diameter bolts in standard holes and is 25 ft in length. The double angle is carrying a dead load of 40 kips and a live load of 120 kips in tension. Verify the strength by both LRFD and ASD.

Solution: Material Properties: 2L442 ASTM A36 Geometric Properties: For a single L442

Fy = 36 ksi Ag = 3.75 in.2 ry = 1.83 in.

Fu = 58 ksi rx = 1.21 in. x = 1.18 in.

Manual Table 2-3 Manual Table 1-7

Calculate the required tensile strength

Pn= 1.2(40.0 kips) + 1.6(120 kips) = 240 kips Calculate the available tensile yield strength Pn = FyAg = (36ksi)(2)(3.75in.2) = 270 kips
LRFD

Pn= 40.0 kips + 120 kips = 160 kips

Eqn. D2-1
ASD

t = 0.90 tPn = 0.90(270 kips) = 243 kips

t = 1.67 Pn /t = (270 kips)/1.67 = 162 kips

Section D2

Calculate the available tensile rupture strength Calculate U 1.18 in. x = 0.944 U = 1 = 1 21.0 in. l

Table D3-1 Case 2

D-13

Calculate An An = Ag 2(dh + z in.)t = 2(3.75in.2) 2(m in. + z in.)(2 in.) = 6.63 in.2 Calculate Ae Ae = AnU = 6.63in.2(0.944) = 6.26 in.2 Pn = FuAe = (58ksi)(6.26 in.2) = 363 kips
LRFD ASD

Section D3.2

Eqn. D3-1 Eqn. D2-2 t = 2.00 Pn/t = (363 kips)/2.00 = 182 kips

t = 0.75 tPn = 0.75(363 kips) = 272 kips

Section D2

The available strength is governed by the tensile yielding limit state.

243 kips > 240 kips

o.k.

162 kips > 160 kips

o.k.

Check the non-mandatory slenderness limit 25.0 ft 12.0 in. L/r = = 248 < 300 o.k. 1.21in. ft

Section D1

D-14

Example D.7
Given:

Pin-Connected Tension Member

An ASTM A36 pin connected tension member with the dimensions shown below carries a dead load of 12 kips and a live load of 4 kips in tension. The diameter of the pin is 1 inch, in a Q-in. oversized hole. Assume that the pin itself is adequate. Verify the strength by both LRFD and ASD.

Solution: Material Properties: Plate ASTM A36 Geometric Properties: w = 4.25 in. t = 0.500 in.

Fy = 36 ksi d = 1.00 in.

Fu = 58 ksi a = 2.25 in. c = 2.50 in.

Manual Table 2-4

Check dimensional requirements: 1) beff = 2t + 0.63 in. = 2(0.500 in.) + 0.63 in. = 1.63 in. 2) a > 1.33beff 3) w > 2beff + d 4) c > a 2.25 in. > (1.33)(1.63 in.) = 2.17 in.
o.k.

Section D5.2

4.25 in. > 2(1.63 in.) + 1.00 in. = 4.26in. 4.25in. o.k. 2.50 in. > 2.25 in.
o.k.

Calculate the required tensile strength

Pu = 1.2(12.0 kips) + 1.6(4.00 kips) = 20.8 kips

Pa = 12.0 kips + 4.00 kips = 16.0 kips

D-15

Calculate the available tensile rupture strength on the net effective area Pn = 2tbeffFu = (2)(0.500 in.)(1.63 in.)(58 ksi) = 94.5 kips
LRFD ASD

Eqn. D5-1

t = 0.75 tPn = 0.75(94.5 kips) = 70.9 kips

t = 2.00 Pn/t = (94.5 kips) / 2.00 = 47.3 kips

Section D5.1

Calculate the available shear rupture strength Asf = 2t(a + d/2) = 2(0.500 in.)[2.25 in. + (1.00 in. /2)] = 2.75 in.2 Pn = 0.6FuAsf = (0.6)(58 ksi)(2.75 in.2) = 95.7 kips
LRFD ASD

Section D5.1 Eqn. D5-2

sf = 0.75 sfPn = 0.75(95.7 kips) = 71.8 kips

sf = 2.00 Pn/sf = (95.7 kips) / 2.00 = 47.9 kips

Section D5.1

Calculate the available bearing strength Apb = 0.500 in.(1.00 in.) = 0.500 in.2 Rn = 1.8FyApb = 1.8(36 ksi)(0.500 in.2) = 32.4 kips
LRFD ASD

Eqn. J7.1

t = 0.75 tPn = 0.75(32.4 kips) = 24.3 kips

t = 2.00 Pn/t = (32.4 kips) / 2.00 = 16.2 kips

Section J7

Calculate the available tensile yielding strength Ag = 4.25 in. (0.500 in.) = 2.13 in.2 Pn = FyAg = 36 ksi (2.13 in.2) = 76.5 kips
LRFD ASD

Section D2 Eqn. D2.1 t = 1.67 Pn/t = (76.5 kips) / 1.67 = 45.8 kips

t = 0.90 tPn = 0.90(76.5 kips) = 68.9 kips

Section D2

The available tensile strength is governed by the bearing strength limit state
LRFD ASD

tPn = 24.3 kips 24.3 kips > 20.8 kips

o.k.

Pn/t = 16.2 kips 16.2 kips > 16.0 kips

o.k.

D-16

Example D.8
Given:

Eyebar Tension Member

See Figure D-8 below. A s in. thick eyebar member, ASTM A36, carries a dead load of 25 kips and a live load of 15 kips in tension. The pin diameter d is 3 in. Verify the strength by both LRFD and ASD.

Solution: Material Properties: Plate ASTM A36 Fy = 36 ksi Geometric Properties: w = 3 in. b = 2.23 in. dh = 3.03 in. db = 3 in.

Fu = 58 ksi t = 0.625 in. R = 8.00 in.

Manual Table 2-4

Check dimensional requirements 1) t > in. 2) w < 8t 3) d > 7/8w 4) dh < d + 1/32 in. 5) R > dh + 2b 6) 2/3w < b < 3/4w 0.625 in. > 0.500 in. o.k. 3.00 in. < 8(0.625 in.) = 5 in. o.k. 3.00 in. > 7/8 (3.00 in.) = 2.63 in. o.k. 3.03 in. < 3.00 in. + (1/32 in.) = 3.03 in. o.k. 8.00 in. > 3.03 in. + 2(2.23 in.) = 7.50 in. o.k. 2/3(3.00 in.) < 2.23 in. < 3/4(3.00 in.) 2.00 in. < 2.23 in. < 2.25 in. o.k.

Section D4.2

D-17

Calculate the required tensile strength

Pu = 1.2(25.0 kips) + 1.6(15.0 kips) = 54.0 kips

Pa = 25.0 kips + 15.0 kips = 40.0 kips

Calculate the available tensile yield strength at the eyebar body (at w) Ag = 3.00 in.(0.625 in.) = 1.88 in.2 Pn= FyAg = (36 ksi)(1.88 in.2) = 67.7 kips
LRFD ASD

Eqn. D2-1 t = 1.67 Pn/t = (67.7 kips)/1.67 = 40.5 kips

t = 0.90 tPn = 0.90(67.7 kips) = 60.9 kips 60.9 kips > 54.0 kips

Section D2

40.3 kips > 40.0 kips

o.k.

The eyebar tension member available strength is governed by the tension yield limit state. Note: The eyebar detailing limitations ensure that the tensile yielding limit state at the eyebar body will control the strength of the eyebar itself. The pin should also be checked for shear yielding, and if the material strength is lower than that of the eyebar, bearing.

D-18

Example D.9
Given:

Find Ae of a Plate with Staggered Bolts

See Fig. D-9 below. A 14 in. wide and 2 in. thick plate subject to tensile loading has staggered holes as shown. Compute An and Ae

Solution:

Calculate net hole diameter dnet = dh + z in. = 0.875 in. Compute the net width for all possible paths across the plate Because of symmetry, many of the net widths are identical and need not be calculated s2 w = 14.0 - d net + 4g w = 14.0 in.- 2(0.875 in.) = 12.3 in. Line A-B-E-F: Line A-B-C-D-E-F: w = 14.0 in.- 4(0.875 in.) + Line A-B-C-D-G: Line A-B-D-E-F:
w = 14.0 in.- 3(0.875 in.) + w = 14.0 in.- 3(0.875 in.) +

Section D3.2

Section D3.2

( 2.50 in.) ( 2.50 in.) ( 2.50 in.)

4(3.00 in.)
2

( 2.50 in.)

4(3.00 in.)

= 11.5 in. (controls)

4(3.00 in.)
2

= 11.9 in. +

( 2.50 in.)

4(7.00 in.)

4(3.00 in.)

= 12.1in.

Therefore, An = (11.5 in.)(0.500 in.) = 5.75 in.2 Calculate U Since tension load is transmitted to all elements by the fasteners U= 1.0 Ae = An(1.0) = 5.75 in.2 Table D3.1 Case 1 Eqn. D3-1