Release Date: Nov. 2021 / Manual Revision: 1.

00

Multi-Way Switchgear Controller ETR606

IEC60870-5-101/104 Protocol
Technical Manual

Copyright © 2021 by ENTEC ELECTRIC & ELECTRONIC CO., LTD all right reserved. Forerunner Distribution & Automation
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Release Note:

[Nov. 2021] Ver1.00

New IEC 60870-5-101/104 Protocol Technical Manual for new type Multi-Way Switchgear Control
ETR606

ENHANCED TECHNOLOGY i
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TABLE OF CONTENTS

A. Introduction ………………………..…………………………………………………………...1

B. Configuration for IEC 60870-5-101/104 ..…....……………………………………………….2

C. Analogue Event Reporting …............…...……………………………………………………11

D. Interoperability Document …...........…...….……………………………………………….13

E. IEC 60870-5-101/104 Point Table ……………………………………………...……………..36

ii ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

A. Introduction

IEC 60870-5 provides a communication method to send basic telecontrol messages between two
systems. The IEC Technical Committee 57 have developed a protocol standard for Tele control,
Teleprotection, and associated telecommunications for electric power systems.

This document is based on IEC 60870-5-101/-104. This document describes communication method
between Entec’s Multi-Way Switchgear Controller ETR606 and Master Station, and provides
“Interoperability Document”, “Point table” and parameter explanations of IEC 60870-5-101/-104.

IEC 60870-5-101/-104 are applied to tele-control equipment and systems with coded bit serial data
transmission for monitoring and controlling geographically widespread processes.
IEC 60870-5-101 protocol uses the standard of asynchronous serial tele-control channel interface
between DTE (Data Terminal Equipment) and DCE (Data Communication Equipment). The standard
is suitable for multiple configurations like point-to-point and multipoint.
IEC 60870-5-104 protocol is an extension of IEC 60870-5-101 protocol with the changes in terms of
transport, network, link & physical layer services for the complete network access. The standard uses
an open TCP/IP interface to network to have connectivity to the LAN(Local Area Network) and
routers with different facility(ISDN, X.25, Frame relay etc) can be used to connect to the WAN (Wide
Area Network). Application layer of IEC 60870-5-104 is preserved same as that of IEC 60870-5-101
with some of the data types and facilities not used. There are two separate link layers defined in the
standard and suitable for data transfer over Ethernet & serial line (PPP - Point-to-Point Protocol).

ENHANCED TECHNOLOGY 1
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

B. Configuration for IEC 60870-5-101/104

1. Configuration for IEC 60870-5-101
Table B-1. Configuration for IEC 60870-5-101

Setting Item Description Step Default

Function Whether to use IEC60870-5-101 (ENABLE, DISABLE) - DISABLE
Port Select Communication Port Setting (RS232-1, RS232-2, RS485) - RS232-1
Link Address Slave(Multi-Way Switchgear Control) address for IEC60870-5-101(1 ~ 65535) 1 1
ASDU Address Application service data unit address (0 ~ 65535) 1 0
Cyclic Period. It is to set interval time between Point set for Cyclic
Cyclic Period 1 60sec
(0(OFF), 1~60000sec)
Event Period Delay time before events are sent (0 ~ 255sec) 1 15sec
D/L Retries Data retires number 1 0
Conf.Timeout Wait time till receive the Data Confirm (ACK) of master after transfer the Data(1 ~ 255sec) 1 10 sec
Max Poll Time Data Polling period time (1 ~ 255sec) 1 10 sec
ASDU Addr Size Size of common address of ASDU(1~2) 1 2
Link Confirm Link layer confirm mode (NEVER, ALWAYS) - ALWAYS
Link Addr Size Link Address Size (1~2) 1 1
Rx Frame Size Maximum size of receive frame (0~261) 1 261
Maximum amount of time to wait for a complete frame after receiving the frame 1
Rx Frame TO 15
sync (0(OFF), 1~255sec)
Tx Frame Size Maximum size of transmit frame (0~261) 1 261
COT Size Size of Cause of transmission (1~2) 1 1
IOA Size Size of information object address (1~3) 1 2
Allowed to send one character response instead of a fixed length NACK when -
One Ch Response NO
no response data available(NO, YES)
Frame Repet’ TO The time out for repetition of frames (0(OFF), 1~255sec) 1 30
Select Timeout The period after a previously received select will timeout (0(OFF), 1~255sec) 1 5
Whether to send Activation Termination upon completion of commands other -
CMD Termination NO
than set point commands(NO, YES)
Whether to send Activation Termination upon completion of set point -
CSE Termination YES
commands (NO, YES).
Clock Sync’ Evt Whether to generate spontaneous clock synchronization events (NO, YES) - YES
MSP Time-Tag Time tag format for single-point (CP56, CP24) - CP56
MIT Time-Tag Time tag format for integrated totals (CP56, CP24) - CP56
Time tag format for measured value and normalized value, in case of general -
MME Time-Tag CP56
event (CP56, CP24)
Time tag format for measured value and normalized value in fault current event -
Flt Time-Tag CP56
(CP56, CP24)

2 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Function
Select whether to use IEC60870-5-101 Protocol.

Port Select
Set physical port to use IEC60870-5-101 communication.

Link Address
Enter the slave address for IEC60870-5-101 communication.

ASDU Address
Enter the Application Service Data Unit Address.

Cyclic Period
Enter the Cyclic Period. It is to set interval time between Point set for Cyclic.

Event Period
Enter the delay time before events are sent. Single event or several events occur and then if new
event is not generated during the delay time, the event(s) already generated is(are) sent to a Master.

D/L Retries
Enter the Data retires number.

Conf. Timeout
Enter the wait time till receive the Data Confirm (ACK) of master after transfer the Data. If there isn’t
the Confirm during this setting time and Data retries is available, Entec’s Multi-Way Switchgear
Control transfers the Data again.

Max Poll Time

Enter the Data Polling period time.

ADSU Addr Size

Enter the size of cause of transmission.

Link Confirm
Enter the Link layer confirm mode.

Link Addr Size

Enter the size of link address.

ENHANCED TECHNOLOGY 3
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Rx Frame Size
Enter the maximum size of received frame.

Rx Frame TO
Enter the maximum amount of time to wait for a complete frame after receiving the frame sync.

Tx Frame Size
Enter the maximum size of transmitted frame.

COT Size
Enter the size of cause of transmission.

IOA Size
Enter the size of information object address.

One Ch Response
This allows to send one character response instead of a fixed length NACK when no response data
available.

Frame Repet’ TO
Enter the time out for repetition of frames(or incremental application layer timeout).

Select Timeout
Enter the period after a previously received select will timeout.

CMD Termination
Select whether to send Activation Termination upon completion of commands other than set point
commands.

CSE Termination
Select whether to send Activation Termination upon completion of set point commands.

Clock Sync’ Evt

Select whether to generate spontaneous clock synchronization events

4 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

MSP Time-Tag
Select whether a time tag format for single-point.

MIT Time-Tag
Select whether a time tag format for integrated totals.

MME Time-Tag
Select whether a time tag format for measured value and normalized value for general event except
for fault current event.

Flt Time-Tag
Select whether a time tag format for measured value and normalized value for fault current event.

ENHANCED TECHNOLOGY 5
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

2. Configuration for IEC 60870-5-104

Table B-4. Configuration for IEC 60870-5-104

Setting Item Description Step Default

Function Whether to use IEC60870-5-104 (ENABLE, DISABLE) - DISABLE
Port Select Communication Port Setting (ETH1, ETH2) - ETH1
ASDU Address Application service data unit address (0 ~ 65535) 1 0
Cyclic Period. It is to set interval time between Point set for Cyclic
Cyclic Period 1 60sec
(0(OFF), 1~60000sec)
Timeout(t0) Timeout for connection establishment (1 ~ 255sec) 1 120 sec
Timeout(t1) Timeout for send or test APDUs(1 ~ 255sec) 1 15 sec
Timeout(t2) Timeout for acknowledgements in case of no data message(1 ~ 255sec) 1 10 sec
Timeout(t3) Timeout for sending test frame in case of a long idle state(1 ~ 255sec) 1 20 sec
Event Period delay time before events are sent(0 ~ 255sec) 1 15sec
TCP/IP Port of Slave(Multi-Way Switchgear Control) for IEC60870-5-104(0 1
TCP Port 2404
~ 65535)
Rx Frame Size Maximum size of receive frame (0~255) 1 255
Tx Frame Size Maximum size of transmit frame (0~255) 1 255
SBO Timeout The period after a previously received select will timeout (0(OFF), 1~255sec) 1 5
Whether to send Activation Termination upon completion of commands other -
CMD Termination YES
than set point commands(NO, YES)
Whether to send Activation Termination upon completion of set point -
CSE Termination YES
commands(NO, YES).
Clock Sync’ Evt Whether to generate spontaneous clock synchronization events (NO, YES) - YES
MSP Time-Tag Time tag format for single-point (CP56, CP24) - CP56
MIT Time-Tag Time tag format for integrated totals (CP56, CP24) - CP56
Time tag format for measured value and normalized value, in case of general -
MME Time-Tag CP56
event (CP56, CP24)
Time tag format for measured value and normalized value in fault current -
Flt Time-Tag CP56
event (CP56, CP24)
Maximum difference receives sequence number to send state variable
k(Max Tx) 1 12
(1 ~ 32767)
w(Max Rx) Latest acknowledge after receiving w I format APDUs (1 ~ 32767) 1 8

Function
Select whether to use IEC60870-5-104 Protocol.

Port Select
Enter a port for IEC60870-5-104 communication.

6 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

ASDU Address
Enter the Application Service Data Unit Address.

Cyclic Period
Enter the Cyclic Period. It is to set interval time between Point set for Cyclic.

Timeout(t0)
Select the Timeout for connection establishment.

Timeout(t1)
Select the Timeout for send or test APDUs.

Timeout(t2)
Select the Timeout for acknowledgements in case of no data message ( t2<t1).

Timeout(t3)
Select the Timeout for sending test frame in case of a long idle state.

Event Period
Select the delay time before events are sent. Single event or several events occur and then if new
event is not generated during the delay time, the event(s) already generated is(are) sent to a Master.

TCP Port
Set the TCP Port of Entec’s Multi-Way Switchgear Control for IEC60870-5-104 Protocol
communication.

Rx Frame Size
Enter the maximum size of received frame.

Tx Frame Size
Enter the maximum size of transmitted frame.
Select Timeout
Enter the period after a previously received select will timeout.

CMD Termination
Select whether to send Activation Termination upon completion of commands other than set point
commands.

ENHANCED TECHNOLOGY 7
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

CSE Termination
Select whether to send Activation Termination upon completion of set point commands.

Clock Sync’ Evt

Select whether to generate spontaneous clock synchronization events.

MSP Time-Tag
Select whether a time tag format for single-point.

MIT Time-Tag
Select whether a time tag format for integrated totals.

MME Time-Tag
Select whether a time tag format for measured value and normalized value for general event except
for fault current event.

Flt Time-Tag
Select whether a time tag format for measured value and normalized value for fault current event.

k(Max Tx)
Set the maximum difference receive sequence number to send state variable.

w(Max Rx)
Set the atest acknowledge after receiving w I format APDUs.

8 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

3. Configuration for IOA(Information Object Address)

Setting Item Description Step Default
Evt Dly Type Delay Type for Event Transmission NOTRIG

MSP Start Single-point information (0 ~ 65535) 1 1000

MDP Start Double-point information (0 ~ 65535) 1 1500

MMENA Start Measured value, normalized value (0 ~ 65535) 1 2000

MMENB Start Measured value, scaled value (0 ~ 65535) 1 2500

MMENC Start Measured value, short floating point value (0 ~ 65535) 1 8000

MMEND Start Measured value, normalized value without quality descriptor (0 ~ 65535) 1 6000

MIT Start Integrated totals (0 ~ 65535) 1 3000

CSC Start Single command (0 ~ 65535) 1 21000

CDC Start Double command (0 ~ 65535) 1 32000

CSEMA Start Set point command, normalized value (0 ~ 65535) 1 26000

CSEMB Start Set point command, scaled value (0 ~ 65535) 1 27000

PMENA Start Parameter of measured value, normalized value (0 ~ 65535) 1 10000

PMENB Start Parameter of measured value, scaled value (0 ~ 65535) 1 12000

PMENC Start Parameter of measured value, short floating point value (0 ~ 65535) 1 14000

MIT Mode Integrated totals mode (MODE B, MODE D) - MODE B

Evt Dly Type

IEC60870-5-101/104 Protocol Delay Type for Event Transmission

MSP Start
IEC60870-5-101/104 Protocol Single-point Information Start Address

MDP Start
IEC60870-5-101/104 Protocol Double-point Information Start Address

MMENA Start
IEC60870-5-101/104 Protocol Measured Value(Normalized Value) Start Address

MMENB Start
IEC60870-5-101/104 Protocol Measured Value(Scaled Value) Start Address

ENHANCED TECHNOLOGY 9
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

MMENC Start
IEC60870-5-101/104 Protocol Measured Value(Short Floating Point Number) Start Address

MMEND Start
IEC60870-5-101/104 Protocol Measured Value(Normalized Value without Quality Descriptor)
Start Address

MIT Start
IEC60870-5-101/104 Protocol Integrated Totals Start Address

CSC Start
IEC60870-5-101/104 Protocol Single Command Start Address

CDC Start
IEC60870-5-101/104 Protocol Double Command Start Address

CSEMA Start
IEC60870-5-101/104 Protocol Set-point Command(Normalized Value) Start Address

CSEMB Start
IEC60870-5-101/104 Protocol Set-point Command(Scaled Value) Start Address

PMENA Start
IEC60870-5-101/104 Protocol Parameter of Measured Values(Normalized Value) Start Address

PMENB Start
IEC60870-5-101/104 Protocol Parameter of Measured Values(Scaled Value) Start Address

PMENC Start
IEC60870-5-101/104 Protocol Parameter of Measured Values(Short Floating Point Number) Start
Address

MIT Mode
IEC60870-5-101/104 Protocol Integrated Totals Mode

10 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

C. Analogue Event Reporting

 Threshold Configuration

NOTE )
“Threshold” used in IEC60870-5-101/104 protocol is described as “Deadband” in the
settings and manuals of all ENTEC’s products.
In order to change the Threshold Configuration for IEC 60870-5-101/104 protocol
communication, change settings such as Limit Low, Limit High, Dead Band or Smoothing
Factor in the “DB MAP CONFIGURATION” setting on the application program.
“Threshold” is described as “Deadband” in the explanation below.

A maximum or minimum value of an analog input can be configured to set the desired range for
analog event reporting. Deadband value is set to generate the event when the analog input’s value
difference between the last value and the current value exceeds the deadband value. The time
period of data updating is 1sec.

Figure C-1. Threshold (Deadband) configuration

- Max./Min. value: Maximum and minimum values set by a device.

- Limit High: Highest value configured by a user
- Limit Low: Lowest value configured by a user
- Smoothing: Not used

ENHANCED TECHNOLOGY 11
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

- Deadband: Event will be generated when during data updating time period (1sec), analog
input’s value difference between the last value and the current value is over the
deadband value configured by a user. For example, in Figure 1, if the value
difference between the analog input’s values at t1 and t2 exceeds the deadband
value, the event occurs. If the measured value at t4 is below the “Limit Low” value,
the value difference between t3 and t4 is considered as the difference between the
analog input value at t3 and t4 and so the variation between t3 and t4 generates
event if it is over the deadband value.
However, after the measured value crosses down the “Limit Low” value once like
the value at t4 and if the subsequent measured values after the time t4 keep
changing below the “Limit Low” value, those variations below the “Limit Low”
value do not generate event even though the variations below the “Limit Low”
value exceeds the deadband value. If the measured value comes in the range
between the “Limit High” and the “Limit Low” values again and the variation at
that time exceeds the deadband value, the event for the variation is generated. In
the same way, an event is generated for the value crossing over or down the “Limit
High” value.

*. “AEvt Method” setting in the “GLOBAL SETTING / COMMUNICATION / EVENT&ETC”

menu of Entec’s Multi-Way Switchgear Control must be set to be “DB” or “BOTH” to generate
analogue events.

12 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

D. Interoperability Document
1. Interoperability Document for IEC 60870-5-101
This document is adapted from the IEC 60870-5-101 standard. For the section the boxes indicate the
following: ▣ – used in standard direction; □ – not used; ■ – cannot be selected in IEC 60870-5-101
standard.

(１) SYSTEM OR DEVICE:

□ System Definition

□ Controlling Station Definition (Master)

▣ Controlled Station Definition (Slave)

(２) NETWORK CONFIGURATION:

▣ Point-to-Point ▣ Multipoint

□ Multiple Point-to-Point □ Multipoint Star

(３) PHYSICAL LAYER

Transmission Speed (control direction):

Unbalanced Interchange Unbalanced Interchange Balanced Interchange circuit

Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:

if>1200 bits/s:

□ 100bits/sec. ▣ 2400bits/sec. ▣ 2400bits/sec.

□ 200bits/sec. ▣ 4800bits/sec. ▣ 4800bits/sec.

□ 300bits/sec. ▣ 9600bits/sec. ▣ 9600bits/sec.

□ 600bits/sec. ▣ 19200bits/sec.

▣ 1200bits/sec. ▣ 38400bits/sec.

▣ 56000bits/sec.

□ 64000bits/sec

ENHANCED TECHNOLOGY 13
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Transmission Speed (monitor direction):

Unbalanced Interchange Unbalanced Interchange Balanced Interchange circuit

Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:

if>1200 bits/s:

□ 100bits/sec. ▣ 2400bits/sec. ▣ 2400bits/sec.

□ 200bits/sec. ▣ 4800bits/sec. ▣ 4800bits/sec.

□ 300bits/sec. ▣ 9600bits/sec. ▣ 9600bits/sec.

□ 600bits/sec. ▣ 19200bits/sec.

▣ 1200bits/sec. ▣ 38400bits/sec.

▣ 56000bits/sec.

□ 64000bits/sec

(４) LINK LAYER

Link Transmission Procedure: Address Field of the Link:

□ Balanced Transmission □ Not Present (Balanced Transmission Only)

▣ Unbalanced Transmission ▣ One Octet

▣ Two Octets (*)

□ Structured

▣ Unstructured
*. NOTE ) The above item marked with * are supported from Ver. 2.05 of
CPU firmware.

Frame Length :

255 : Maximum length L(control direction)

255 : Maximum length L(monitor direction)
Configurable : Time during which repetitions are permitted (Trp) or number of repetitions.

When using an unbalanced link layer, the following ADSU types are returned in class 2 messages (low
priority) with the indicated causes of transmission:

▣ The standard assignment of ADSUs to class 2 messages is used as follows:

Type identification Cause of transmission

9 <1>

□ A special assignment of ADSUs to class 2 messages is used as follows:

※ Note) In response to a class 2 poll, a controller station may respond with class 1 data when there is no
class 2 data available.

14 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

(５) APPLICATION LAYER

Transmission Mode for Application Data:
Mode 1 (least significant octet first), as defined in Clause 4.10 of IEC 60870-5-1, is used exclusively in this
companion standard.

Common Address of ADSU:

▣ One Octet (*) ▣ Two Octets

*. NOTE ) The above item marked with * are supported from Ver. 2.05 of CPU firmware.

Information Object Address:

▣ One Octet (*) □ Structured

▣ Two Octets ▣ Unstructured

▣ Three Octets (*)

*. NOTE ) The above item marked with * are supported from Ver. 2.05 of CPU firmware.

Cause of Transmission:
▣ One Octet

▣ Two Octets (with originator address). Originator address is set to zero if not used. (*)

*. NOTE ) The above item marked with * are supported from Ver. 2.05 of CPU firmware.

Selection of standard ASDUs:

For the following lists, the boxes indicate the following:

▣– used in standard direction; □ – not used; ■ – cannot be selected in IEC 60870-5-104 standard.

Process information in monitor direction

▣ <1> := Single-point information M_SP_NA_1

▣ <2> := Single-point information with time tag(**) M_SP_TA_1

▣ <3> := Double-point information M_DP_NA_1

■ <4> := Double-point information with time tag M_DP_TA_1

□ <5> := Step position information M_ST_NA_1

■ <6> := Step position information with time tag M_ST_TA_1

□ <7> := Bitstring of 32 bits M_BO_NA_1

■ <8> := Bitstring of 32 bits with time tag M_BO_TA_1

▣ <9> := Measured value, normalized value M_ME_NA_1

▣ <10> := Measured value, normalized value with time tag(**) M_NE_TA_1

ENHANCED TECHNOLOGY 15
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

▣ <11> := Measured value, scaled value M_ME_NB_1

■ <12> := Measured value, scaled value with time tag M_NE_TB_1

□ <13> := Measured value, short floating point value M_ME_NC_1

■ <14> := Measured value, short floating point value with time tag M_NE_TC_1

▣ <15> := Integrated totals M_IT_NA_1

▣ <16> := Integrated totals with time tag(**) M_IT_TA_1

■ <17> := Event of protection equipment with time tag M_EP_TA_1

■ <18> := Packed start events of protection equipment with time tag M_EP_TB_1

■ <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1

■ <20> := Packed single-point information with status change detection M_SP_NA_1

▣ <21> := Measured value, normalized value without quantity descriptor M_ME_ND_1

▣ <30> := Single-point information with time tag CP56Time2a M_SP_TB_1

▣ <31> := Double-point information with time tag CP56Time2a M_DP_TB_1

□ <32> := Step position information with time tag CP56Time2a M_ST_TB_1

□ <33> := Bitstring of 32 bits with time tag CP56Time2a M_BO_TB_1

▣ <34> := Measured value, normalized value with time tag CP56Time2a (*) M_ME_TD_1

□ <35> := Measured value, scaled value with time tag CP56Time2a M_ME_TE_1

□ <36> := Measured value, short floating point value with time tag CP56Time2a M_ME_TF_1

▣ <37> := Integrated totals with time tag CP56Time2a M_IT_TB_1

□ <38> := Event of protection equipment with time tag CP56Time2a M_EP_TD_1

□ <39> := Packed start events of protection equipment with time tag CP56Time2a M_EP_TE_1

□ <40> := Packed output circuit information of protection equipment

with time tag CP56Time2a M_EP_TF_1

Either the ASDUs of the set <2>, <4>, <6>, <8>, <10>, <12>, <14>, <16>, <17>, <18>, and <19> or of the

set <30> to <40> are used.

*. NOTE ) 1. The above item marked with * are supported from Ver. 2.05 of CPU firmware.
2. The above item marked with * are supported from Ver. 2.10 of CPU firmware.

Process information in control direction

▣ <45> := Single command C_SC_NA_1

▣ <46> := Double command C_DC_NA_1

□ <47> := Regulating step command C_RC_NA_1

▣ <48> := Set point command, normalized value C_SE_NA_1

□ <49> := Set point command, scaled value C_SE_NB_1

□ <50> := Set point command, short floating point value C_SE_NC_1

□ <51> := Bitstring of 32 bits C_BO_NA_1

16 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

System information in monitor direction

▣ <70> := End of initialization M_EI_NA_1

System information in control direction

▣ <100> := Interrogation command C_IC_NA_1

▣ <101> := Counter interrogation command C_CI_NA_1

▣ <102> := Read command C_RD_NA_1

▣ <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1

■<104> := Test command C_TS_NA_1

▣<105> := Reset process command C_RP_NA_1

■<106> := Delay acquisition command C_CD_NA_1

Parameter in control direction

▣ <110> := Parameter of measured value, normalized value PE_ME_NA_1

□ <111> := Parameter of measured value, scaled value PE_ME_NB_1

□ <112> := Parameter of measured value, short floating point value PE_ME_NC_1

□ <113> := Parameter activation PE_AC_NA_1

File transfer
□ <120> := File Ready F_FR_NA_1

□ <121> := Section Ready F_SR_NA_1

□ <122> := Call directory, select file, call file, call section F_SC_NA_1
□ <123> := Last section, last segment F_LS_NA_1

□ <124> := Ack file, ack section F_AF_NA_1

□ <125> := Segment F_SG_NA_1

□ <126> := Directory C_CD_NA_1

Type identifier and cause of transmission assignments

(station-specific parameters)

In the following table:

• Shaded boxes are not required.

• Black boxes are not permitted in this companion standard.

• Blank boxes indicate functions or ASDU not used.

•‘X’ if only used in the standard direction

ENHANCED TECHNOLOGY 17
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<1> M_SP_NA_1 X X X

<2> M_SP_TA_1** X X X

<3> M_DP_NA_1

<4> M_DP_TA_1

<5> M_ST_NA_1

<6> M_ST_TA_1

<7> M_BO_NA_1

<8> M_BO_TA_1

<9> M_ME_NA_1 X X X X

<10> M_ME_TA_1** X

<11> M_ME_NB_1

<12> M_ME_TB_1

<13> M_ME_NC_1

<14> M_ME_TC_1

<15> M_IT_NA_1 X X

<16> M_IT_TA_1** X

<17> M_EP_TA_1

<18> M_EP_TB_1

<19> M_EP_TC_1

<20> M_PS_NA_1

<21> M_ME_ND_1 X X

<30> M_SP_TB_1 X X X

<31> M_DP_TB_1

18 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<32> M_ST_TB_1

<33> M_BO_TB_1

<34> M_ME_TD_1* X

<35> M_ME_TE_1

<36> M_ME_TF_1

<37> M_IT_TB_1* X

<38> M_EP_TD_1

<39> M_EP_TE_1

<40> M_EP_TF_1

<45> C_SC_NA_1 X X X X X

<46> C_DC_NA_1

<47> C_RC_NA_1

<48> C_SE_NA_1 X X X X X

<49> C_SE_NB_1

<50> C_SE_NC_1

<51> C_BO_NA_1

<70> M_EI_NA_1* X

<100> C_IC_NA_1 X X X X X

<101> C_CI_NA_1 X X X

<102> C_RD_NA_1 X

<103> C_CS_NA_1 X X X

<104> C_TS_NA_1

<105> C_RP_NA_1 X X

ENHANCED TECHNOLOGY 19
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<106> C_CD_NA_1

<110> P_ME_NA_1 X X X

<111> P_ME_NB_1

<112> P_ME_NC_1

<113> P_AC_NA_1

<120> F_FR_NA_1

<121> F_SR_NA_1

<122> F_SC_NA_1

<123> F_LS_NA_1

<124> F_AF_NA_1

<125> F_SG_NA_1

<126> F_DR_TA_1*

- Blank or X only
*. NOTE ) 1. The above item marked with * are supported from Ver. 2.05 of CPU firmware.
2. The above item marked with * are supported from Ver. 2.10 of CPU firmware.

20 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

(６) BASIC APPLICATION

FUNCTIONS Station Initialization:
▣ Remote initialization

Cyclic Data Transmission:

▣ Cyclic data transmission

Read Procedure:
▣ Read procedure

Spontaneous Transmission:
▣ Spontaneous transmission

Double transmission of information objects with cause of transmission

spontaneous:
The following type identifications may be transmitted in succession caused by a single status change of an

information object. The particular information object addresses for which double transmission is enabled
are defined in a project-specific list.

□ Single point information: M_SP_NA_1, M_SP_TA_1, M_SP_TB_1, and M_PS_NA_1

□ Double point information: M_DP_NA_1, M_DP_TA_1, and M_DP_TB_1

□ Step position information: M_ST_NA_1, M_ST_TA_1, and M_ST_TB_1

□ Bitstring of 32 bits: M_BO_NA_1, M_BO_TA_1, and M_BO_TB_1 (if defined for a specific project)

□ Measured value, normalized value: M_ME_NA_1, M_ME_TA_1, M_ME_ND_1, and M_ME_TD_1

□ Measured value, scaled value: M_ME_NB_1, M_ME_TB_1, and M_ME_TE_1

□ Measured value, short floating point number: M_ME_NC_1, M_ME_TC_1, and M_ME_TF_1

Station interrogation:
▣ Global

▣ Group 1 ▣ Group 5 ▣ Group 9 ▣ Group 13

▣ Group 2 ▣ Group 6 ▣ Group 10 ▣ Group 14

▣ Group 3 ▣ Group 7 ▣ Group 11 ▣ Group 15

▣ Group 4 ▣ Group 8 ▣ Group 12 ▣ Group 16

ENHANCED TECHNOLOGY 21
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Clock synchronization:
▣ Clock synchronization (optional)

□ Day of week used

▣ RES1, GEN (time tag substituted/ not substituted) used

□ SU-bit (summertime) used

Command transmission:
▣ Direct command transmission

▣ Direct set point command transmission

▣ Select and execute command

▣ Select and execute set point command

□ C_SE ACTTERM used

□ No additional definition

▣ Short pulse duration (duration determined by a system parameter in the outstation)

▣ Long pulse duration (duration determined by a system parameter in the outstation)

□ Persistent output

Transmission of integrated totals:

▣ Mode A: Local freeze with spontaneous transmission (**)

▣ Mode B: Local freeze with counter interrogation (**)

▣ Mode C: Freeze and transmit by counter-interrogation commands (**)

▣ Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously (**)

▣ Counter read

▣ Counter freeze without reset (**)

▣ Counter freeze with reset (**)

▣ Counter reset (**)

▣ General request counter

▣ Request counter group 1 (**)

▣ Request counter group 2 (**)

▣ Request counter group 3 (**)

▣ Request counter group 4 (**)

*. NOTE ) The above item marked with ** are supported from Ver. 2.10 of CPU firmware.

22 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Parameter loading:
▣ Threshold value

□ Smoothing factor

▣ Low limit for transmission of measured values

▣ High limit for transmission of measured values

Parameter activation:
□ Activation/deactivation of persistent cyclic or periodic transmission of the addressed object

Test procedure:
□ Test procedure

File transfer:
File transfer in monitor direction:

□ Transparent file

□ Transmission of disturbance data of protection equipment

□ Transmission of sequences of events

□ Transmission of sequences of recorded analog values

File transfer in control direction:

□ Transparent file

Background scan:
□ Background scan

Acquisition of transmission delay:

□ Acquisition of transmission delay

ENHANCED TECHNOLOGY 23
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

2. Interoperability Document for IEC 60870-5-104

This document is adapted from the IEC 60870-5-104 standard. For the section the boxes indicate the
following: ▣ – used in standard direction; □ – not used; ■ – cannot be selected in IEC 60870-5-104
standard.

(１) SYSTEM OR DEVICE:

□ System Definition

□ Controlling Station Definition (Master)

▣ Controlled Station Definition (Slave)

(２) NETWORK CONFIGURATION:

■ Point-to-Point ■ Multipoint

■ Multiple Point-to-Point ■ Multipoint Star

(３) PHYSICAL LAYER

Transmission Speed (control direction):

Unbalanced Interchange Unbalanced Interchange Balanced Interchange circuit

Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:

if>1200 bits/s:

■ 100bits/sec. ■ 2400bits/sec. ■ 2400bits/sec.

■ 200bits/sec. ■ 4800bits/sec. ■ 4800bits/sec.

■ 300bits/sec. ■ 9600bits/sec. ■ 9600bits/sec.

■ 600bits/sec. ■ 19200bits/sec.

■ 1200bits/sec. ■ 38400bits/sec.

■ 56000bits/sec.

■ 64000bits/sec.

24 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Transmission Speed (monitor direction):

Unbalanced Interchange Unbalanced Interchange Balanced Interchange circuit

Circuit V.24/V.28 Standard: Circuit V.24/V.28 Recommended X.24/X.27:

if>1200 bits/s:

■ 100bits/sec. ■ 2400bits/sec. ■ 2400bits/sec.

■ 200bits/sec. ■ 4800bits/sec. ■ 4800bits/sec.

■ 300bits/sec. ■ 9600bits/sec. ■ 9600bits/sec.

■ 600bits/sec. ■ 19200bits/sec.

■ 1200bits/sec. ■ 38400bits/sec.

■ 56000bits/sec.

■ 64000bits/sec.

(４) LINK LAYER

Link Transmission Procedure: Address Field of the Link:

■ Balanced Transmission ■ Not Present (Balanced Transmission Only)

■ Unbalanced Transmission ■ One Octet

■ Two Octets

■ Structured

■ Unstructured

Frame Length (maximum length, number of octets): Not selectable in companion IEC 60870-5-104 standard

When using an unbalanced link layer, the following ADSU types are returned in class 2 messages (low
priority) with the indicated causes of transmission:

■ The standard assignment of ADSUs to class 2 messages is used as follows:

■ A special assignment of ADSUs to class 2 messages is used as follows:

(５) APPLICATION LAYER

Transmission Mode for Application Data:
Mode 1 (least significant octet first), as defined in Clause 4.10 of IEC 60870-5-4, is used exclusively in this
companion standard.

Common Address of ADSU:

■ One Octet ▣ Two Octets

ENHANCED TECHNOLOGY 25
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Information Object Address:

■ One Octet □ Structured

■ Two Octets □ Unstructured

▣ Three Octets

Cause of Transmission:
■ One Octet

▣ Two Octets (with originator address). Originator address is set to zero if not used.

Maximum Length of APDU: 253 (the maximum length may be reduced by the system.)

Selection of standard ASDUs:

For the following lists, the boxes indicate the following:

▣– used in standard direction; □ – not used; ■ – cannot be selected in IEC 60870-5-104 standard.

Process information in monitor direction

▣ <1> := Single-point information M_SP_NA_1

▣ <2> := Single-point information with time tag(**) M_SP_TA_1

▣ <3> := Double-point information M_DP_NA_1

■ <4> := Double-point information with time tag M_DP_TA_1

□ <5> := Step position information M_ST_NA_1

■ <6> := Step position information with time tag M_ST_TA_1

□ <7> := Bitstring of 32 bits M_BO_NA_1

■ <8> := Bitstring of 32 bits with time tag M_BO_TA_1

▣ <9> := Measured value, normalized value M_ME_NA_1

▣ <10> := Measured value, normalized value with time tag(**) M_NE_TA_1

□ <11> := Measured value, scaled value M_ME_NB_1

■ <12> := Measured value, scaled value with time tag M_NE_TB_1

□ <13> := Measured value, short floating point value M_ME_NC_1

■ <14> := Measured value, short floating point value with time tag M_NE_TC_1

▣ <15> := Integrated totals M_IT_NA_1

▣ <16> := Integrated totals with time tag(**) M_IT_TA_1

■ <17> := Event of protection equipment with time tag M_EP_TA_1

■ <18> := Packed start events of protection equipment with time tag M_EP_TB_1

■ <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1
■ <20> := Packed single-point information with status change detection M_SP_NA_1

26 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

▣ <21> := Measured value, normalized value without quantity descriptor M_ME_ND_1

▣ <30> := Single-point information with time tag CP56Time2a M_SP_TB_1

▣ <31> := Double-point information wiht time tag CP56Time2a M_DP_TB_1

□ <32> := Step position information with time tag CP56Time2a M_ST_TB_1

□ <33> := Bitstring of 32 bits with time tag CP56Time2a M_BO_TB_1

▣ <34> := Measured value, normalized value with time tag CP56Time2a (*) M_ME_TD_1

▣ <35> := Measured value, scaled value with time tag CP56Time2a M_ME_TE_1

□ <36> := Measured value, short floating point value with time tag CP56Time2a M_ME_TF_1

▣ <37> := Integrated totals with time tag CP56Time2a M_IT_TB_1

□ <38> := Event of protection equipment with time tag CP56Time2a M_EP_TD_1

□ <39> := Packed start events of protection equipment with time tag CP56Time2a M_EP_TE_1

□ <40> := Packed output circuit information of protection equipment

with time tag CP56Time2a M_EP_TF_1

Either the ASDUs of the set <2>, <4>, <6>, <8>, <10>, <12>, <14>, <16>, <17>, <18>, and <19> or of the

set <30> to <40> are used.

*. NOTE ) 1. The above item marked with * are supported from Ver. 2.05 of CPU firmware.
2. The above item marked with * are supported from Ver. 2.10 of CPU firmware.

Process information in control direction

▣ <45> := Single command C_SC_NA_1

▣ <46> := Double command C_DC_NA_1

□ <47> := Regulating step command C_RC_NA_1

▣ <48> := Set point command, normalized value C_SE_NA_1

□ <49> := Set point command, scaled value C_SE_NB_1

□ <50> := Set point command, short floating point value C_SE_NC_1

□ <51> := Bitstring of 32 bits C_BO_NA_1

□ <58> := Single command with time tag CP56Time2a C_SC_TA_1

□ <59> := Double command with time tag CP56Time2a C_DC_TA_1

□ <60> := Regulating step command with time tag CP56Time2a C_RC_TA_1

□ <61> := Set point command, normalized value with time tag CP56Time2a C_SE_TA_1

□ <62> := Set point command, scaled value with time tag CP56Time2a C_SE_TB_1

□ <63> := Set point command, short floating point value with time tag CP56Time2a C_SE_TC_1

□ <64> := Bitstring of 32 bits with time tag CP56Time2a C_BO_TA_1

Either the ASDUs of the set <45> to <51> or of the set <58> to <64> are used.

ENHANCED TECHNOLOGY 27
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

System information in monitor direction

▣ <70> := End of initialization M_EI_NA_1

System information in control direction

▣ <100> := Interrogation command C_IC_NA_1

▣ <101> := Counter interrogation command C_CI_NA_1

▣ <102> := Read command C_RD_NA_1

▣ <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1

■<104> := Test command C_TS_NA_1

▣<105> := Reset process command C_RP_NA_1

■<106> := Delay acquisition command C_CD_NA_1

▣<107> := Test command with time tag CP56Time2a C_TS_TA_1

Parameter in control direction

▣ <110> := Parameter of measured value, normalized value PE_ME_NA_1

□ <111> := Parameter of measured value, scaled value PE_ME_NB_1

□ <112> := Parameter of measured value, short floating point value PE_ME_NC_1

□ <113> := Parameter activation PE_AC_NA_1

File transfer
□ <120> := File Ready F_FR_NA_1

□ <121> := Section Ready F_SR_NA_1

□ <122> := Call directory, select file, call file, call section F_SC_NA_1

□ <123> := Last section, last segment F_LS_NA_1

□ <124> := Ack file, ack section F_AF_NA_1

□ <125> := Segment F_SG_NA_1

□ <126> := Directory (blank or X, available only in monitor [standard] direction) C_CD_NA_1

Type identifier and cause of transmission assignments

(station-specific parameters)

In the following table:

• Shaded boxes are not required.

• Black boxes are not permitted in this companion standard.

• Blank boxes indicate functions or ASDU not used.

•‘X’ if only used in the standard direction

28 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<1> M_SP_NA_1 X X X

<2> M_SP_TA_1** X X X

<3> M_DP_NA_1

<4> M_DP_TA_1

<5> M_ST_NA_1

<6> M_ST_TA_1

<7> M_BO_NA_1

<8> M_BO_TA_1

<9> M_ME_NA_1 X X X X

<10> M_ME_TA_1** X

<11> M_ME_NB_1

<12> M_ME_TB_1

<13> M_ME_NC_1

<14> M_ME_TC_1

<15> M_IT_NA_1 X X

<16> M_IT_TA_1** X

<17> M_EP_TA_1

<18> M_EP_TB_1

<19> M_EP_TC_1

<20> M_PS_NA_1

<21> M_ME_ND_1 X X

<30> M_SP_TB_1 X X X

<31> M_DP_TB_1

ENHANCED TECHNOLOGY 29
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<32> M_ST_TB_1

<33> M_BO_TB_1

<34> M_ME_TD_1* X

<35> M_ME_TE_1

<36> M_ME_TF_1

<37> M_IT_TB_1* X

<38> M_EP_TD_1

<39> M_EP_TE_1

<40> M_EP_TF_1

<45> C_SC_NA_1 X X X X X

<46> C_DC_NA_1

<47> C_RC_NA_1

<48> C_SE_NA_1 X X X X X

<49> C_SE_NB_1

<50> C_SE_NC_1

<51> C_BO_NA_1

<58> C_SC_TA_1 X X X X X

<59> C_DC_TA_1

<60> C_RC_TA_1

<61> C_SE_TA_1 X X X X X

<62> C_SE_TB_1

<63> C_SE_TC_1

<64> C_BO_TA_1

30 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

TYPE CAUSE OF TRANSMISSION

IDENTIFICATION

PERIODIC, CYCLIC

BACKGROUND SCAN

SPONTANEOUS

INITIALIZED

REQUEST OR REQUESTED

ACTIVATION

ACTIVATION CONFIRMATION

DEACTIVATION

DEACTIVATION CONFIRMATION

ACTIVATION TERMINATION

RETURN INFO CAUSED BY REMOTE CMD

RETURN INFO CAUSED BY LOCAL CMD

FILE TRANSFER

INTERROGATED BY GROUP <NUMBER>

REQUEST BY GROUP <N> COUNTER REQ

UNKNOWN TYPE IDENTIFICATION

UNKNOWN CAUSE OF TRANSMISSION

UNKNOWN COMMON ADDRESS OF ADSU

UNKNOWN INFORMATION OBJECT ADDR

20 37
NO. MNEMONIC 1 2 3 4 5 6 7 8 9 10 11 12 13 to to 44 45 46 47
36 41

<70> M_EI_NA_1* X

<100> C_IC_NA_1 X X X X X

<101> C_CI_NA_1 X X X

<102> C_RD_NA_1 X

<103> C_CS_NA_1 X X X

<104> C_TS_NA_1

<105> C_RP_NA_1 X X

<106> C_CD_NA_1

<107> C_TS_TA_1 X X

<110> P_ME_NA_1 X X X

<111> P_ME_NB_1

<112> P_ME_NC_1

<113> P_AC_NA_1

<120> F_FR_NA_1

<121> F_SR_NA_1

<122> F_SC_NA_1

<123> F_LS_NA_1

<124> F_AF_NA_1

<125> F_SG_NA_1

<126> F_DR_TA_1*

- Blank or X only
*. NOTE ) 1. The above item marked with * are supported from Ver. 2.05 of CPU firmware.
2. The above item marked with * are supported from Ver. 2.10 of CPU firmware.

ENHANCED TECHNOLOGY 31
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

(６) BASIC APPLICATION

FUNCTIONS Station Initialization:
▣ Remote initialization

Cyclic Data Transmission:

▣ Cyclic data transmission

Read Procedure:
▣ Read procedure

Spontaneous Transmission:
▣ Spontaneous transmission

Double transmission of information objects with cause of transmission

spontaneous:
The following type identifications may be transmitted in succession caused by a single status change of an

information object. The particular information object addresses for which double transmission is enabled
are defined in a project-specific list.

□ Single point information: M_SP_NA_1, M_SP_TA_1, M_SP_TB_1, and M_PS_NA_1

□ Double point information: M_DP_NA_1, M_DP_TA_1, and M_DP_TB_1

□ Step position information: M_ST_NA_1, M_ST_TA_1, and M_ST_TB_1

□ Bitstring of 32 bits: M_BO_NA_1, M_BO_TA_1, and M_BO_TB_1 (if defined for a specific project)

□ Measured value, normalized value: M_ME_NA_1, M_ME_TA_1, M_ME_ND_1, and M_ME_TD_1

□ Measured value, scaled value: M_ME_NB_1, M_ME_TB_1, and M_ME_TE_1

□ Measured value, short floating point number: M_ME_NC_1, M_ME_TC_1, and M_ME_TF_1

Station interrogation:
▣ Global

▣ Group 1 ▣ Group 5 ▣ Group 9 ▣ Group 13

▣ Group 2 ▣ Group 6 ▣ Group 10 ▣ Group 14

▣ Group 3 ▣ Group 7 ▣ Group 11 ▣ Group 15

▣ Group 4 ▣ Group 8 ▣ Group 12 ▣ Group 16

32 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Clock synchronization:
▣ Clock synchronization (optional)

Command transmission:
▣ Direct command transmission

▣ Direct set point command transmission

▣ Select and execute command

▣ Select and execute set point command

□ C_SE ACTTERM used

□ No additional definition

▣ Short pulse duration (duration determined by a system parameter in the outstation)

▣ Long pulse duration (duration determined by a system parameter in the outstation)

□ Persistent output
▣ Supervision of maximum delay in command direction of commands and set point commands

Maximum allowable delay of commands and set point commands: 10 s

Transmission of integrated totals:

▣ Mode A: Local freeze with spontaneous transmission

▣ Mode B: Local freeze with counter interrogation

▣ Mode C: Freeze and transmit by counter-interrogation commands

▣ Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously

▣ Counter read

▣ Counter freeze without reset

▣ Counter freeze with reset

▣ Counter reset

▣ General request counter

▣ Request counter group 1

▣ Request counter group 2

▣ Request counter group 3

▣ Request counter group 4

Parameter loading:
▣ Threshold value

□ Smoothing factor

▣ Low limit for transmission of measured values

▣ High limit for transmission of measured values

ENHANCED TECHNOLOGY 33
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Parameter activation:
□ Activation/deactivation of persistent cyclic or periodic transmission of the addressed object

Test procedure:
□ Test procedure

File transfer:
File transfer in monitor direction:

□ Transparent file

□ Transmission of disturbance data of protection equipment

□ Transmission of sequences of events

□ Transmission of sequences of recorded analog values

File transfer in control direction:

□ Transparent file

Background scan:
□ Background scan

Acquisition of transmission delay:

■ Acquisition of transmission delay

Definition of time outs:

PARAMETER DEFAULT REMARKS SELECTED

VALUE VALUE

t0 30 s Timeout of connection establishment 120 s

t1 15 s Timeout of send or test APDUs 15 s

t2 10 s Timeout for acknowledgements in case of no data messages t2 < t1 10 s

t3 20 s Timeout for sending test frames in case of a long idle state 20 s

Maximum range of values for all time outs: 1 to 255 s, accuracy 1 s

34 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Maximum number of outstanding I-format APDUs k and latest acknowledge

APDUs (w):

PARAMETER DEFAULT REMARKS SELECTED

VALUE VALUE

k 12 APDUs Maximum difference receive sequence number to send state variable 12 APDUs

w 8 APDUs Latest acknowledge after receiving w I-format APDUs 8 APDUs

Maximum range of values k: 1 to 32767 (215 – 1) APDUs, accuracy 1 APDU

Maximum range of values w: 1 to 32767 APDUs, accuracy 1 APDU

Recommendation: w should not exceed two-thirds of k.

Port number:

PARAMETER VALUE REMARKS

Port number 2404 In all cases

RFC 2200 suite:

RFC 2200 is an official Internet Standard which describes the state of standardization of protocols used in

the Internet as determined by the Internet Architecture Board (IAB). It offers a broad spectrum of actual

standards used in the Internet. The suitable selection of documents from RFC 2200 defined in this standard
for given projects has to be chosen by the user of this standard.

▣ Ethernet 802.3

□ Serial X.21 interface

□ Other selection(s) from RFC 2200 (list below if selected)

ENHANCED TECHNOLOGY 35
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

E. IEC 60870-5-101/104 Point Table

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (1/6)

Single-point information

Status S: Spontaneous , G: General Group, C: cyclic

Object
Description Point Property Group Available Base
Address 0 1
S G C No. SW CB No.*
1000 GAS ALARM OK LOW ۷ ۷ 2 〇 〇 90

1001 DOOR OPEN CLOSE OPEN ۷ ۷ 2 〇 〇 91

1002 AC POWER FAIL OK FAIL ۷ ۷ 2 〇 〇 93

1003 POWER DOWN NORMAL DOWN ۷ ۷ 2 〇 〇 100

1004 BATTERY VOLTAGE BAD NORMAL BAD ۷ ۷ 2 〇 〇 99

1005 CHARGER VOLTAGE BAD NORMAL BAD ۷ ۷ 2 〇 〇 96

1006 DIAGNOSTIC ERROR STATUS NORMAL FAIL ۷ ۷ 2 〇 〇 36

1007 REMOTE ENABLED : COMMON LOCAL REMOTE ۷ ۷ 2 〇 〇 105

1008 CONTROL LOCK : COMMON UNLOCK LOCK ۷ ۷ 2 〇 〇 103

1009 1 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 63

1010 1 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 70

1011 1 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 65

1012 1 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 67

1013 1 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 112

1014 1 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 114

1015 1 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 116

1016 1 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 357

1017 1 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 359

1018 1 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 117

1019 1 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 349

1020 1 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 350

1021 1 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 351

1022 1 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 345

1023 1 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 346

1024 1 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 328

1025 1 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 151

1026 1 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 152

1027 1 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 163

36 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (2/6)

Object Status Point Property Group Available Base
Description
Address 0 1 S G C No. SW CB No.*
1028 1 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 164

1029 1 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 165

1030 1 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 162

1031 1 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 157

1032 1 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 130

1033 1 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 131

1034 2 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 173

1035 2 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 172

1036 2 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 174

1037 2 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 175

1038 2 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 179

1039 2 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 181

1040 2 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 183

1041 2 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 187

1042 2 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 188

1043 2 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 189

1044 2 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 190

1045 2 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 193

1046 2 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 194

1047 2 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 191

1048 2 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 192

1049 2 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 205

1050 2 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 206

1051 2 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 207

1052 2 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 218

1053 2 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 219

1054 2 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 220

1055 2 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 217

1056 2 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 212

1057 2 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 185

1058 2 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 186

1059 3 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 228

1060 3 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 227

ENHANCED TECHNOLOGY 37
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (3/6)

Object Status Point Property Group Available Base
Description
Address 0 1 S G C No. SW CB No.*
1061 3 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 229

1062 3 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 230

1063 3 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 234

1064 3 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 236

1065 3 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 238

1066 3 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 242

1067 3 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 243

1068 3 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 244

1069 3 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 245

1070 3 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 248

1071 3 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 249

1072 3 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 246

1073 3 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 247

1074 3 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 260

1075 3 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 261

1076 3 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 262

1077 3 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 273

1078 3 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 274

1079 3 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 275

1080 3 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 272

1081 3 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 267

1082 3 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 240

1083 3 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 241

1084 4 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 283

1085 4 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 282

1086 4 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 284

1087 4 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 285

1088 4 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 289

1089 4 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 291

1090 4 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 293

1091 4 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 297

1092 4 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 298

1093 4 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 299

38 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (4/6)

Object Status Point Property Group Available Base
Description
Address 0 1 S G C No. SW CB No.*
1094 4 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 300

1095 4 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 303

1096 4 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 304

1097 4 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 301

1098 4 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 302

1099 4 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 315

1100 4 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 316

1101 4 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 317

1102 4 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 328

1103 4 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 329

1104 4 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 330

1105 4 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 327

1106 4 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 322

1107 4 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 295

1108 4 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 296

1109 5 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 338

1110 5 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 337

1111 5 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 339

1112 5 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 340

1113 5 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 344

1114 5 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 346

1115 5 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 348

1116 5 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 352

1117 5 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 353

1118 5 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 354

1119 5 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 355

1120 5 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 358

1121 5 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 359

1122 5 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 356

1123 5 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 357

1124 5 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 370

1125 5 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 371

1126 5 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 372

ENHANCED TECHNOLOGY 39
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (5/6)

Object Status Point Property Group Available Base
Description
Address 0 1 S G C No. SW CB No.*
1127 5 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 383

1128 5 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 384

1129 5 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 385

1130 5 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 382

1131 5 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 377

1132 5 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 350

1133 5 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 351

1134 6 WAY : Close/Open Status OPEN CLOSE ۷ ۷ 2 〇 〇 393

1135 6 WAY : Trouble Status OK TROUBLE ۷ ۷ 2 〇 〇 392

1136 6 WAY : Earth Status DEASSERT ASSERT ۷ ۷ 2 〇 〇 394

1137 6 WAY : Mechanism Lock FREE LOCK ۷ ۷ 2 〇 〇 395

1138 6 WAY : Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 399

1139 6 WAY : Ground Protection Enabled DISABLE ENABLE ۷ ۷ 2 〇 〇 401

1140 6 WAY : Alternate Set Group Enabled PRIMARY ALTERNATE ۷ ۷ 2 〇 〇 403

1141 6 WAY : Fault Target - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 407

1142 6 WAY : Fault Target - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 408

1143 6 WAY : Fault Target - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 409

1144 6 WAY : Fault Target - Ground DEASSERT ASSERT ۷ ۷ 2 〇 〇 410

1145 6 WAY : Fault Target - Temporary DEASSERT ASSERT ۷ ۷ 2 〇 〇 413

1146 6 WAY : Fault Target - Permanent DEASSERT ASSERT ۷ ۷ 2 〇 〇 414

1147 6 WAY : Fault Target - Forward DEASSERT ASSERT ۷ ۷ 2 〇 〇 411

1148 6 WAY : Fault Target - Reverse DEASSERT ASSERT ۷ ۷ 2 〇 〇 412

1149 6 WAY : 79 Reset - 79 RESET ۷ ۷ 2 X 〇 425

1150 6 WAY : 79 Cycle - 79 CYCLE ۷ ۷ 2 X 〇 426

1151 6 WAY : 79 Lockout - 79 L.O ۷ ۷ 2 X 〇 427

1152 6 WAY : Open Phase - A DEASSERT ASSERT ۷ ۷ 2 〇 〇 438

1153 6 WAY : Open Phase - B DEASSERT ASSERT ۷ ۷ 2 〇 〇 439

1154 6 WAY : Open Phase - C DEASSERT ASSERT ۷ ۷ 2 〇 〇 440

1155 6 WAY : Phase Difference Timeout DEASSERT ASSERT ۷ ۷ 2 〇 〇 437

1156 6 WAY : Live Voltage Timeout DEAD LIVE ۷ ۷ 2 〇 〇 432

1157 6 WAY : Forward Power Flow - FORWARD ۷ ۷ 2 〇 〇 405

1158 6 WAY : Reverse Power Flow - REVERSE ۷ ۷ 2 〇 〇 406

40 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-1. IEC60870-5-101/104 INDEX – Single-point information (6/6)

NOTE
1. “SW Type” and “CB Type” indicate whether each index point is available or not when SW Type (Load breaker

Switch) or CB Type(Circuit breaker Switch) is set. “〇” indicates that the point is available and "X" indicates the
unavailable point.

2. The Start Address of “Single Points” can change by “MSP Start” in “Global Setting >> Communication >>

Protocols >> IEC60870-5 >> Common” menu.

3. All “Single Points” above can change assigned “Object Address”, “Point Property” and “Group No.” on EMIS

Interface Software. Please refer to “EMIS Interface Software User’s Manual” for more detail information.
4. By the use of the "Base Number" specified to each point above, the detailed description for the corresponding

point can be confirmed on "Table 1. BASE DATA POINTS - BINARY INPUT" of the "ETR606 Communication

Protocol MAP Configuration User Manual".

ENHANCED TECHNOLOGY 41
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-2. IEC 60870-5-101/104 INDEX – Single Command (1/3)

Single Command

Object TR/CL Base

Description Block Condition
Address Field No*
COMMON : Control Lock CLOSE
21000 85
COMMON : Control Unlock TRIP

21001 COMMON : Battery Load Test CLOSE 72

21002 COMMON : Target Reset CLOSE 73

1 WAY : CB Close CLOSE Control Lock or Close Block Note 3

21003 0
1 WAY : CB Open TRIP Control Lock or Trip Block Note 4

1 WAY : Protection Enable CLOSE

21004 Control Lock 2
1 WAY : Protection Disable TRIP

1 WAY : Ground Protection Enable CLOSE

21005 Control Lock 4
1 WAY : Ground Protection Disable TRIP

1 WAY : Primary Set Group Change CLOSE

21006 Control Lock 10
1 WAY : Alternate Set Group Change TRIP

21007 1 WAY : Wave Capture CLOSE 11

Note 3
2 WAY : CB Close CLOSE Control Lock or Close Block
21008 12
2 WAY : CB Open TRIP Control Lock or Trip Block Note 4

2 WAY : Protection Enable CLOSE

21009 Control Lock 14
2 WAY : Protection Disable TRIP

2 WAY : Ground Protection Enable CLOSE

21010 Control Lock 16
2 WAY : Ground Protection Disable TRIP

2 WAY : Primary Set Group Change CLOSE

21011 Control Lock 22
2 WAY : Alternate Set Group Change TRIP

21012 2 WAY : Wave Capture CLOSE 23

3 WAY : CB Close CLOSE Control Lock or Close Block Note 3

21013 24
3 WAY : CB Open TRIP Control Lock or Trip Block Note 4

3 WAY : Protection Enable CLOSE

21014 Control Lock 26
3 WAY : Protection Disable TRIP

3 WAY : Ground Protection Enable CLOSE

21015 Control Lock 28
3 WAY : Ground Protection Disable TRIP

3 WAY : Primary Set Group Change CLOSE

21016 Control Lock 34
3 WAY : Alternate Set Group Change TRIP

21017 3 WAY : Wave Capture CLOSE 35

42 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-2. IEC 60870-5-101/104 INDEX – Single Command (2/3)

Object TR/CL Base
Description Block Condition
Address Field No*
4 WAY : CB Close CLOSE Control Lock or Close Block Note 3
21018 36
4 WAY : CB Open TRIP Control Lock or Trip Block Note 4

4 WAY : Protection Enable CLOSE

21019 Control Lock 38
4 WAY : Protection Disable TRIP

4 WAY : Ground Protection Enable CLOSE

21020 Control Lock 40
4 WAY : Ground Protection Disable TRIP

4 WAY : Primary Set Group Change CLOSE

21021 Control Lock 46
4 WAY : Alternate Set Group Change TRIP

21022 4 WAY : Wave Capture CLOSE 47

5 WAY : CB Close CLOSE Control Lock or Close Block Note 3

21023 48
5 WAY : CB Open TRIP Control Lock or Trip Block Note 4

5 WAY : Protection Enable CLOSE

21024 Control Lock 50
5 WAY : Protection Disable TRIP

5 WAY : Ground Protection Enable CLOSE

21025 Control Lock 52
5 WAY : Ground Protection Disable TRIP

5 WAY : Primary Set Group Change CLOSE

21026 Control Lock 58
5 WAY : Alternate Set Group Change TRIP

21027 5 WAY : Wave Capture CLOSE 59

Note 3
6 WAY : CB Close CLOSE Control Lock or Close Block
21028 60
6 WAY : CB Open TRIP Control Lock or Trip Block Note 4

6 WAY : Protection Enable CLOSE

21029 Control Lock 62
6 WAY : Protection Disable TRIP

6 WAY : Ground Protection Enable CLOSE

21030 Control Lock 64
6 WAY : Ground Protection Disable TRIP

6 WAY : Primary Set Group Change CLOSE

21031 Control Lock 70
6 WAY : Alternate Set Group Change TRIP

21032 6 WAY : Wave Capture CLOSE 71

NOTE (1/2)
1. All the “Single Command” points above are available in both control types, SW (Load Breaker Switch) or CB

(Circuit Breaker).

2. The Start Address of “Single Command” can change by “CSC Start” in “Global Setting >> Communication >>

Protocols >> IEC60870-5 >> Common” menu.

ENHANCED TECHNOLOGY 43
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-2. IEC 60870-5-101/104 INDEX – Single Command (3/3)

NOTE (2/2)
3. Close Block status appears if at least one of the following conditions is met. This Close Block status was

included in the default PLC configuration, and it can be customized according to the user's preference through

the PLC setting menu of ETIMS Interface Software ;

- Gas Alarm (Gas Pressure Low or Gas Pressure High) status (available if Tank is Gas Type),

- Close Block Input status,

- Mechanism Lock status,

- Earth status,

- or Phase Difference
4. Trip Block status appears if at least one of the following conditions is met. This Trip Block status was included

in the default PLC configuration, and it can be customized according to the user's preference through the PLC

setting menu of ETIMS Interface Software ;

- Gas Alarm (Gas Pressure Low or Gas Pressure High) status (available if Tank is Gas Type),

- Mechanism Lock status,

- or Earth status
5. All “Single Command” points can change assigned Object Address and the value(ON/OFF) of single command

can be inverted on ETIMS Interface Software. Please refer to “ETIMS Interface Software User’s Manual” for
more detail information.

44 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-3. IEC60870-5-101/104 - Integrated Totals (1/2)

Integrated Totals Point

Object Base
Description Point Property Group No. Notes
Address No.
3000 Restart General Group 1 16bit / 32bit 0

3001 Diagnosis General Group 1 16bit / 32bit 1

3002 1 WAY : Operation General Group 1 16bit / 32bit 2

3003 1 WAY : Trip General Group 1 16bit / 32bit 3

3004 1 WAY : Fault Indication - A General Group 1 16bit / 32bit 6

3005 1 WAY : Fault Indication - B General Group 1 16bit / 32bit 7

3006 1 WAY : Fault Indication - C General Group 1 16bit / 32bit 8

3007 1 WAY : Fault Indication - Ground General Group 1 16bit / 32bit 9

3008 2 WAY : Operation General Group 1 16bit / 32bit 46

3009 2 WAY : Trip General Group 1 16bit / 32bit 47

3010 2 WAY : Fault Indication - A General Group 1 16bit / 32bit 50

3011 2 WAY : Fault Indication - B General Group 1 16bit / 32bit 51

3012 2 WAY : Fault Indication - C General Group 1 16bit / 32bit 52

3013 2 WAY : Fault Indication - Ground General Group 1 16bit / 32bit 53

3014 3 WAY : Operation General Group 1 16bit / 32bit 90

3015 3 WAY : Trip General Group 1 16bit / 32bit 91

3016 3 WAY : Fault Indication - A General Group 1 16bit / 32bit 94

3017 3 WAY : Fault Indication - A General Group 1 16bit / 32bit 95

3018 3 WAY : Fault Indication - B General Group 1 16bit / 32bit 96

3019 3 WAY : Fault Indication - C General Group 1 16bit / 32bit 97

3020 3 WAY : Fault Indication - Ground General Group 1 16bit / 32bit 134

3021 4 WAY : Operation General Group 1 16bit / 32bit 135

3022 4 WAY : Trip General Group 1 16bit / 32bit 138

3023 4 WAY : Fault Indication - A General Group 1 16bit / 32bit 139

3024 4 WAY : Fault Indication - B General Group 1 16bit / 32bit 140

3025 4 WAY : Fault Indication - C General Group 1 16bit / 32bit 141

3026 4 WAY : Fault Indication - Ground General Group 1 16bit / 32bit 178

3027 5 WAY : Operation General Group 1 16bit / 32bit 179

3028 5 WAY : Trip General Group 1 16bit / 32bit 182

3029 5 WAY : Fault Indication - A General Group 1 16bit / 32bit 183

3030 5 WAY : Fault Indication - B General Group 1 16bit / 32bit 184

ENHANCED TECHNOLOGY 45
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-3. IEC60870-5-101/104 - Integrated Totals (2/2)

Object Base
Description Point Property Group No. Notes
Address No.
3031 5 WAY : Fault Indication -Ground General Group 1 16bit / 32bit 185

3032 6 WAY : Operation General Group 1 16bit / 32bit 222

3033 6 WAY : Trip General Group 1 16bit / 32bit 223

3034 6 WAY : Fault Indication - A General Group 1 16bit / 32bit 226

3035 6 WAY : Fault Indication - B General Group 1 16bit / 32bit 227

3036 6 WAY : Fault Indication - C General Group 1 16bit / 32bit 228

3037 6 WAY : Fault Indication - Ground General Group 1 16bit / 32bit 229

NOTE
1. Counter format can be selected (16 bit or 32 bit(Default)) by “16bit Count Use” in “MAIN MENU >> GLOBAL

SETTING >> GENERAL >> DEVICE >> OTHERS” menu.

- 16bit Counter roll over Counter 65535.

- 32bit Counter roll over Counter 1,000,000.

2. The Start Address of “Integrated Totals” can change by “MIT Start” in “Global Setting >> Communication >>

Protocols >> IEC60870-5 >> Common” menu.

3. All the “Integrated Totals” points above are available in both control types, SW (Load Breaker Switch) or CB (Circuit

Breaker).

4. All “Integrated Totals” Points can change assigned Point Property, Group Number and Object Address on EMIS

Interface Software. Please refer to “EMIS Interface Software User’s Manual” for more detail information.

46 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-4. IEC60870-5-101/104 – Normalized Measured (1/5)

Normalized Measured

S: Spontaneous , G: General Group, C: Cyclic

Object
Description Point Property Group Base No*
Address Data Format
S G C No.
2000 COMMON : Frequency - 1 Way ۷ 16 1Hz/1Count 153

2001 COMMON : Frequency - 4 Way ۷ 16 1Hz/2Count 154

2002 1 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 155

2003 1 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 156

2004 1 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 157

2005 1 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 158

2006 1 WAY : RMS Voltage - A ۷ 16 1V/1Count 165

2007 1 WAY : RMS Voltage - B ۷ 16 1V/1Count 166

2008 1 WAY : RMS Voltage - C ۷ 16 1V/1Count 167

2009 1 WAY : Active Power - A ۷ 16 1KW/1Count 187

2010 1 WAY : Active Power - B ۷ 16 1KW/1Count 188

2011 1 WAY : Active Power - C ۷ 16 1KW/1Count 189

2012 1 WAY : Reactive Power - A ۷ 16 1KVar/1Count 195

2013 1 WAY : Reactive Power - B ۷ 16 1KVar/1Count 196

2014 1 WAY : Reactive Power - C ۷ 16 1KVar/1Count 197

2015 1 WAY : Power Factor - A ۷ 16 1%/1Count 201

2016 1 WAY : Power Factor - B ۷ 16 1%/1Count 202

2017 1 WAY : Power Factor - C ۷ 16 1%/1Count 203

2018 1 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 233

2019 1 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 234

2020 1 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 235

2021 1 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 236

2022 2 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 240

2023 2 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 244

2024 2 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 252

2025 2 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 256

2026 2 WAY : RMS Voltage - A ۷ 16 1V/1Count 245

2027 2 WAY : RMS Voltage - B ۷ 16 1V/1Count 246

2028 2 WAY : RMS Voltage - C ۷ 16 1V/1Count 247

2029 2 WAY : Active Power - A ۷ 16 1KW/1Count 248

ENHANCED TECHNOLOGY 47
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-4. IEC60870-5-101/104 – Normalized Measured (2/5)

S: Spontaneous , G: General Group, C: Cyclic
Object
Description Point Property Group Base No*
Address Data Format
S G C No.
2030 2 WAY : Active Power - B ۷ 16 1Hz/1Count 19

2031 2 WAY : Active Power - C ۷ 16 1KW/1Count 163

2032 2 WAY : Reactive Power - A ۷ 16 1KVar/1Count 165

2033 2 WAY : Reactive Power - B ۷ 16 1KVar/1Count 166

2034 2 WAY : Reactive Power - C ۷ 16 1KVar/1Count 167

2035 2 WAY : Power Factor - A ۷ 16 1%/1Count 173

2036 2 WAY : Power Factor - B ۷ 16 1%/1Count 174

2037 2 WAY : Power Factor - C ۷ 16 1%/1Count 175

2038 2 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 201

2039 2 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 202

2040 2 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 203

2041 2 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 204

2042 3 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 230

2043 3 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 231

2044 3 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 232

2045 3 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 233

2046 3 WAY : RMS Voltage - A ۷ 16 1V/1Count 244

2047 3 WAY : RMS Voltage - B ۷ 16 1V/1Count 245

2048 3 WAY : RMS Voltage - C ۷ 16 1V/1Count 246

2049 3 WAY : Active Power - A ۷ 16 1KW/1Count 262

2050 3 WAY : Active Power - B ۷ 16 1KW/1Count 263

2051 3 WAY : Active Power - C ۷ 16 1KW/1Count 264

2052 3 WAY : Reactive Power - A ۷ 16 1KVar/1Count 266

2053 3 WAY : Reactive Power - B ۷ 16 1KVar/1Count 267

2054 3 WAY : Reactive Power - C ۷ 16 1KVar/1Count 268

2055 3 WAY : Power Factor - A ۷ 16 1%/1Count 274

2056 3 WAY : Power Factor - B ۷ 16 1%/1Count 275

2057 3 WAY : Power Factor - C ۷ 16 1%/1Count 276

2058 3 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 302

2059 3 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 303

2060 3 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 304

2061 3 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 305

48 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-4. IEC60870-5-101/104 – Normalized Measured (3/5)

S: Spontaneous , G: General Group, C: Cyclic
Object
Description Point Property Group Base No*
Address Data Format
S G C No.
2062 4 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 331

2063 4 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 332

2064 4 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 333

2065 4 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 334

2066 4 WAY : RMS Voltage - A ۷ 16 1V/1Count 345

2067 4 WAY : RMS Voltage - B ۷ 16 1V/1Count 346

2068 4 WAY : RMS Voltage - C ۷ 16 1V/1Count 347

2069 4 WAY : Active Power - A ۷ 16 1KW/1Count 363

2070 4 WAY : Active Power - B ۷ 16 1KW/1Count 364

2071 4 WAY : Active Power - C ۷ 16 1KW/1Count 365

2072 4 WAY : Reactive Power - A ۷ 16 1KVar/1Count 367

2073 4 WAY : Reactive Power - B ۷ 16 1KVar/1Count 368

2074 4 WAY : Reactive Power - C ۷ 16 1KVar/1Count 369

2075 4 WAY : Power Factor - A ۷ 16 1%/1Count 375

2076 4 WAY : Power Factor - B ۷ 16 1%/1Count 376

2077 4 WAY : Power Factor - C ۷ 16 1%/1Count 377

2078 4 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 403

2079 4 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 404

2080 4 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 405

2081 4 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 406

2082 5 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 432

2083 5 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 433

2084 5 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 434

2085 5 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 435

2086 5 WAY : RMS Voltage - A ۷ ۷ 16 1A/1Count 446

2087 5 WAY : RMS Voltage - B ۷ 16 1V/1Count 447

2088 5 WAY : RMS Voltage - C ۷ 16 1V/1Count 448

2089 5 WAY : Active Power - A ۷ 16 1V/1Count 464

2090 5 WAY : Active Power - B ۷ 16 1KW/1Count 465

2091 5 WAY : Active Power - C ۷ 16 1KW/1Count 466

2092 5 WAY : Reactive Power - A ۷ 16 1KW/1Count 468

2093 5 WAY : Reactive Power - B ۷ 16 1KVar/1Count 469

ENHANCED TECHNOLOGY 49
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-4. IEC60870-5-101/104 – Normalized Measured (4/5)

S: Spontaneous , G: General Group, C: Cyclic
Object
Description Point Property Group Base No*
Address Data Format
S G C No.
2094 5 WAY : Reactive Power - C ۷ 16 1KVar/1Count 470

2095 5 WAY : Power Factor - A ۷ 16 1%/1Count 476

2096 5 WAY : Power Factor - B ۷ 16 1%/1Count 477

2097 5 WAY : Power Factor - C ۷ 16 1%/1Count 478

2098 5 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 504

2099 5 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 505

2100 5 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 506

2101 5 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 507

2102 6 WAY : RMS Current - A ۷ ۷ 16 1A/1Count 533

2103 6 WAY : RMS Current - B ۷ ۷ 16 1A/1Count 534

2104 6 WAY : RMS Current - C ۷ ۷ 16 1A/1Count 535

2105 6 WAY : RMS Current - Ground ۷ ۷ 16 1A/1Count 536

2106 6 WAY : RMS Voltage - A ۷ 16 1V/1Count 547

2107 6 WAY : RMS Voltage - B ۷ 16 1V/1Count 548

2108 6 WAY : RMS Voltage - C ۷ 16 1V/1Count 549

2109 6 WAY : Active Power - A ۷ 16 1KW/1Count 565

2110 6 WAY : Active Power - B ۷ 16 1KW/1Count 566

2111 6 WAY : Active Power - C ۷ 16 1KW/1Count 567

2112 6 WAY : Reactive Power - A ۷ 16 1KVar/1Count 569

2113 6 WAY : Reactive Power - B ۷ 16 1KVar/1Count 570

2114 6 WAY : Reactive Power - C ۷ 16 1KVar/1Count 571

2115 6 WAY : Power Factor - A ۷ 16 1%/1Count 577

2116 6 WAY : Power Factor - B ۷ 16 1%/1Count 578

2117 6 WAY : Power Factor - C ۷ 16 1%/1Count 579

2118 6 WAY : Fault Current - A ۷ ۷ 16 1A/1Count 605

2119 6 WAY : Fault Current - B ۷ ۷ 16 1A/1Count 606

2120 6 WAY : Fault Current - C ۷ ۷ 16 1A/1Count 607

2121 6 WAY : Fault Current - Ground ۷ ۷ 16 1A/1Count 608

NOTE (1/2)
1. The Start Address of “Normalized Measured” can change by “MMENA Start” in “Global Setting >>

Communication >> Protocols >> IEC60870-5 >> Common” menu.

50 ENHANCED TECHNOLOGY
IEC 60870-5-101/104 PROTOCOL http://www.entecene.co.kr

Table E-4. IEC60870-5-101/104 – Normalized Measured (5/5)

NOTE (2/2)
2. Object Address Point of Normalized Measurands has three Parameter normalized Value(Threshold, Low Limit,

High Limit) and these are dedicated for Group 14 in General Interrogation.

Following tables shows IOA, Value, Flags( Threshold, Low Limit, High Limit) at address 2000.

Address IOA Value Flags

10000 50 0х01(Threshold)

2000 10002 -32000 0х03(Low Limit)

10003 32000 0х04(High Limit)

To change Value, do Parameter normalized value command and dedicate new Address and Flags.

Each Object Address Point are 2000~2121 and it has three values (Threshold, Low Limit, High Limit). Threshold

IOA at address 2000 is 10000 and High Limit IOA of “6 WAY : Fault Current - Ground” at address 2121 is, 10487.

3. The meaning of the Group Number assigned the each point is as below;

- Group 16: Measuring

- Group 14: Normalized Measurands’ Threshold, Low limit, High limit measuring

4. All the “Normalized Measurands” points above are available in both control types, SW (Load Breaker Switch)

or CB (Circuit Breaker).

*. All “Normalized Measurands” Points can change Data Format by “Scale” setting on ETIMS Interface Software. Please
refer to “ETIMS Interface Software User’s Manual” for more detail information.
*. All “Normalized Measurands” Points can change assigned Point Property, Group Number and Object Address on
ETIMS Interface Software. Please refer to “ETIMS Interface Software User’s Manual” for more detail information.
*. By the use of the "Base Map Number" specified to each point above, the detailed description for the corresponding

point can be confirmed on "Table 4. BASE DATA POINTS - ANALOG INPUT" of the “ETR606 Communication

Protocol MAP Configuration User Manual".

ENHANCED TECHNOLOGY 51