Shenzhen Hi-Link Electronic Co.
, Ltd
HLK-ZW0906 Datasheet
Round Fingerprint Module with Light
Version:V1.0 Revision Date:2024-1-26 Copyright@Shenzhen Hi-Link Electronic Co., Ltd
CONTENTS
1. PRODUCT PROFILE ..............................................................................................1
2. PARAMETERS .........................................................................................................1
2.1 TECHNICAL INDICATORS ................................................................................1
2.2 MECHANICAL CHARACTERISTICS ..............................................................2
2.3 DIMENSIONAL DRAWINGS .............................................................................. 2
3. ELECTRICAL PARAMETERS .............................................................................3
4. INTERFACE DEFINITIONS ................................................................................. 3
4.1 COMMUNICATION INTERFACE .....................................................................3
4.2 CONNECTOR TYPES .......................................................................................... 4
4.3. PIN DESCRIPTIONS ......................................................................................... 4
4.4 PHYSICAL PHOTOGRAPHS ............................................................................. 6
4.5. DESCRIPTION OF THE INTERNAL CIRCUITRY OF THE
FINGERPRINT MODULE ......................................................................................... 6
5. RECORD OF REVISION ..................................................................................... 10
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
1. Products
Fingerprint identification module is used for user's identity determination,
when the user touches the fingerprint identification module with his/her finger,
the fingerprint identification module will scan the user's fingerprints, and the
algorithm chip can obtain the fingerprint image data for registration and
comparison operation. This product is suitable for various applications that
require fingerprint identification.
2. Parametric
2.1. Technical indicators
Item Parameters
storage capacity 100 fingerprint data as standard
Sensor type Capacitive Touch Sensors
resolution (of a photo) 508DPI
FRR. <3 per cent
FAR. <0.001 per cent
Fingerprint sensor shape orbicular
Image grey level 8-bit greyscale
service life million times
Static Test Contact discharge ±8KV/Air discharge ±15KV
data interface UART (TTL level)
Sensor surface hardness 3H
1
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
Operating temperature and
-25℃~+70℃: 45%~85%RH
humidity range
Storage temperature and
-40℃~+85℃: 45%~95%RH
humidity range
2.2. Mechanical property
Item Description Unit
Overall dimensions Φ12.8mm mm
functional areas 5.6*4.8 mm
connection method UART
sensor size 112*96
2.3. Dimension drawing
2
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
3. Electrical parameters
sports event minimal quintessential greatest unit (of measure)
Supply Voltage 3.0 3.3 3.6 V
Standby current (sensor) - 10 12 μA
Operating Current
24 35 50 mA
(Algorithmic MCU)
Mapping time 50 60 70 ms
Eigenvalue generation time 65 70 80 ms
Comparison time 20 600 1100 ms
Power-on start-up time - 67 100 ms
noncontact
- 15 - KV
discharge
ESD rating
contact
- 8 - KV
discharge
4. Interface definition
4.1. Communication interface
Standard UART default baud rate 57600 bps, 1 start bit, 1 stop bit, 8
data bits, no parity bit, 3.3V TTL level.
3
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
4.2. Connector Type
XH-1.00-6P: 6Pin standoff connector with 1.00mm pitch.
4.3. Pin Description
4.4.
pin name (of a
define typology note
number thing)
1 GND ground P earth signal
Serial Receiver
2 RXD I Serial Data Input
RXD
Serial
3 TXD Transmitter O Serial data output
TXD
For powering Power supply for the
VDD_3.3
4 the fingerprint P fingerprint module as a
V
module as a whole (make sure that
4
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
whole this power supply is
switched off in standby
mode).
Interrupt wake-up
signal (high level
5 Detect wake-up call O output when finger
touches the fingerprint
sensor)
SENSOR
SENSOR_ SENSOR Modular
6 Modular Power P
3.3V Power Supply
Supply
Description:
The serial port is a 3.3V TTL level. If you want to connect to the serial
port of a PC, you need to connect a TTL-USB adapter board to
communicate.
The 6-pin SENSOR module circuit power supply needs to be
powered all the time. Make sure that this power supply has low ripple
and is not disturbed by other power supplies.
5
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
4.5. Photograph
4.6. Fingerprint Module Internal Circuit
Description
Directly adopting the fingerprint sensor FD mode, SENSOR wake-up is
highly reliable and reduces the risk of false triggering.
The Detect signal line is low in the no-finger-touch state, and the signal
is triggered to high when the finger touches the fingerprint sensor until
the finger leaves and then becomes low again.
Fingerprint module workflow description:
Detect is used as a wake-up signal when the fingerprint module is
dormant. When the finger touches the fingerprint sensor, the interrupt
signal is triggered to wake up the system, and the master MCU controls
MCU_3.3V to power on; after the fingerprint module algorithm chip is
powered on and initialised, the master MCU controls the fingerprint
module to complete the tasks of image acquisition, enrolment, and
6
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
comparison through the serial commands, and after the tasks are
completed, the master chip controls the fingerprint module to hibernate,
and controls MCU_3.3V to power off, and the system enters into
hibernation and wait for the next round of work. After the system wakes
up, the master MCU can shield the interrupt signal and turn on the
interrupt detection again before hibernation after the task is completed.
Fingerprint sensor chip power supply requirements.
Fingerprint chip has its own characteristics, in FD (FingerDetect)
mode, i.e. when the fingerprint sensor is scanning and detecting
fingerprints periodically, there will be a peak current of about 200mA for
4us. Therefore, the power supply of the fingerprint chip has strict
requirements. sensor_3.3V should control the power ripple within
200mV, to avoid too large power ripple causing the fingerprint sensor to
reset at a low voltage, which will lead to the fingerprint sensor not
working properly.
7
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
Fingerprint chip operating current in FD mode
The LDO module with fast transient response is required to supply
power to the fingerprint chip; it is recommended that the output current
of the LDO for Sensor power supply should be ≥250mA, the ripple
should be <100mV, and the PSRR should be >60dB.
8
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
It is recommended to use a separate LDO to supply power to the
fingerprint module. the LDO output is routed all the way to the
fingerprint chip to supply power, and separated all the way to the
fingerprint module algorithm MCU power supply with MOS switch
control.
When the fingerprint module shares the LDO power supply with other
modules, the fingerprint module power supply needs to be routed
separately from the LDO output on the PCB layout.
9
HLK-ZW0906
Shenzhen Hi-Link Electronic Co., Ltd
Specification
5. Version Revision Record
releases revised description dates proposer
V1.0 first draft (of writing) 2024-1-26 Chrales
Shenzhen Hi-Link Electronic Co., Ltd
Address：17F,Building E, Xinghe WORLD, Minzhi Street, Long Hua district,
Shenzhen 51813
Email：[email protected]
Website：www.hlktech.net
10
