Q #1.
Full from of CCNA –
a) Cisco Certified Network Associate
b) CCNA Certified Network Association
c) Certified of Cisco Network Administration
d) Cisco Certified Network Association
Answers: (a) Cisco Certified Network Associate.
Q #2. Which of the following company is associated with CCNA –
a) Microsoft
b) Google
c) Apple
d) Cisco
Answers: (d) Cisco.
Q #3. Which of the following command is used to find the joined multicast groups for an IPv6
interface –
a) Router# Show ipv6 multicast
b) Router# Show ipv6 groups
c) Router# Show ipv6 interface gi 0/1
d) Router# Show ipv6 multicast groups
Answers: (c) Router# Show ipv6 interface gi 0/1.
Q #4. Link State Routing protocols are used algorithm –
a) DUAL
b) Bellman-Ford
c) Dijkstra
d) None of the above
Answers: (c) Dijkstra.
Q #5. Which of the following command is used to configure the Switch –
a) User EXEC mode
b) Privileged mode
c) Global configuration mode
d) Global interface mode
Answers: (c) Global configuration mode.
Q #6. Which of the following has stored startup configuration of a Router –
a) ROM
b) Flash
c) RAM
d) NVRAM
Answers: (d) NVRAM.
Q #7. When are link-state packets sent to the neighbors –
a) Every 30 seconds
b) Every 60 seconds
c) Every 180 seconds
d) When a link goes up or down
Answers: (d) When a link goes up or down.
Q #8. How many bytes is an Ethernet address –
a) 4
b) 6
c) 16
d) 48
Answers: (b)
6. Q #9. Which of the following command is used to show the RIP routing updates –
a) Show ip route
b) Show ip protocol
c) Show ip rip
d) Debug ip rip
Answers: (d) Debug ip rip.
Q #10. Where the EIGRP successor routes are stored –
a) In the Neighbour only
b) In the Routing table only
c) In the Topology and Neighbour table only
d)In the Routing and the Topology table
Answers: (d) In the Routing and the Topology table.
Q #11. Which of the following term is used to be Port Address Translation –
a) NAT Fast
b) NAT Static
c) NAT Overload
d) NAT Start
Answers: (c) NAT Overload.
Q #12. Which of the following commands is used to show the IOS image files available in flash
memory –
a) #show flash
b) #show IOS file
c) #show image
d) #show IOS image
Answers: (a) #show flash.
Q #13. Which of the following command is used to configure all the default VTY ports on a router –
a) Router#line vty 0 4
b) Router(config)#line vty 0 4
c) Router#line vty all
d) Router(config)#line vty all
Answers: (a) Router#line vty 0 4
Q #14. Which of the following mode is used to reboot the router after erase all the data of NVRAM –
a) User EXEC mode
b) User Privileged mode
c) Setup mode
d) ROMMON mode
Answers: (c) Setup mode.
Q #15. Which of the following is a STP convergence Time –
a) 50 seconds
b) 60 seconds
c) 70 seconds
d) 80 seconds
Answers: (a) 50 seconds.
Q #16. PVST is a type of ______ protocol –
a) Router Information Protocol
b) LINK State Protocol
c) Hybrid Protocol
d) Spanning Tree Protocol
Answers: (d) Spanning Tree Protocol.
Q #17. The default Bridge Priority value is –
a) 65565
b) 65535
c) 63353
d) 63553
Answers: (b) 65535.
Q #18. Rapid Spanning Tree Protocol (RSTP) is a proprietary –
a) Cisco
b) ICAN
c) IEEE 802.1w
d)IANA
Answers: (c) IEEE 802.1w
Q #19. Which of the following protocol is used to maintain a loop-free network –
a) STP
b) VTP
c) RIP
d) OSPF
Answers: (a) STP.
Q #20. Which of the following statement are true for VTP –
a) All switches are vtp transparent by default
b) VTP is on by default with a domain name of cisco on all cisco devices
c) All switches are vtp client by default
d) All switches are vtp server by default
Answers: (d) All switches are vtp server by default.
Q #21. Which of the following feature can be used to carry all the VLAN traffic on one link from a
Switch to a Router –
a) PAGP
b) LACP
c) Trunking
d) ACL
Answers: (c) Trunking.
Q #22. Which of the following trunking protocol used to trunk link between two cisco switches –
a) PPP
b) 802.1q
c) ISL
d) CHAP
Answers: (c) ISL.
Q #23. Which of the following modes to use to see the command –
a) Privileged
b) Global Configuration
c) User EXEC
d) Line Configuration
Answers: (a) Privileged.
Q #24. Which of the following command is used in Cisco at User mode to enter Privileged EXEC mode
–
a) Admin
b) Enable
c) Disable
d) Enter
Answers: (b) Enable.
Q #25. Which of the following prompts is a Router Privileged EXEC mode –
a) Router>
b) Router#
c) Router(config)
d) Router()
Answers: (b) Router
#. Q #26. Which of the following is default ad value of RIP –
a) 120
b) 130
c) 0
d) 90
Answers: (a)
Q #27. Which of the following protocol is used to default point-to-point encapsulation in a Cisco
Router –
a) PPP
b) SLIP
c) ATM
d) HDLC
Answers: (c) ATM.
Q #28. What is the default AD value of OSPF –
a) 110
b) 120
c) 90
d) 0
Answers: (a) 110.
Q #29. Wildcard mask of 255.255.255.252 is –
a) 0.0.0.255
b) 0.255.255.255
c) 0.0.3.0
d) 0.0.0.3
Answers: (d) 0.0.0.3
Q #30. Link State Protocol works with _____ algorithm –
a) Bellman Ford
b) Dijkstra
c) DUAL
d) None of the above
Answers: (b) Dijkstra.
Q #31. Which of the following protocol is known as “Routing by Rumor” –
a) Distance Vector
b) Link State
c) Hybrid
d) None of the above
Answers: (a) Distance Vector.
Q #32. Which of the following protocol is a Hybrid Protocol –
a) RIP
b) OSPF
c) IGRP
d) EIGRP
Answers: (d) EIGRP.
Q #33. The maximum Hop Count of RIP is –
a) 15
b) 16
c) 17
d) 10
Answers: (a) 15.
Q #34. What is stands for OSPF –
a) Open Short Path Find
b) Open Start Path First
c) Open Shortest Path First
d) Open Stand Path First
Answers: (c) Open Shortest Path First.
Q #35. What is the matric value of EIGRP –
a) K-value
b) Bps value
c) Bits
d) None of the above
Answers: (a) K-value.
Q #36. Which of the following is a not types of switching –
a) Circuit Switching
b) Packet Switching
c) Datagram Packet Switching
d) Vital Packet Switching
Answers: (d) Vital Packet Switching.
Q #37. In a MAC address the first 24 bits is called as –
a) Organizationally Unique Identifier
b) Organizationally Administered Address
c) Universally Administered Address
d) Universally Unique Identifier Address
Answer: (a) Organizationally Unique Identifier.
Q #38. In a MAC address the last 24 bits is called as –
a) Organizationally Unique Identifier
b) Organizationally Administered Address
c) Universally Administered Address
d) Universally Unique Identifier Address
Answer: (c) Universally Administered Address.
Q #39. Which types of address is used in an Ethernet frame header –
a) Logical address only
b) IP address only
c) MAC address only
d) Broadcast address only
Answers: (c) MAC address only.
Q #40. Which of the following is true about ROMMON mode –
a) It is a temporary storage for the IOS image
b) It is a memory management tool
c) It is Boot mode, when the router does not find the valid IOS image in flash memory, then the
system will enter ROMMON mode
d) None of the above
Answers: (c) It is Boot mode, when the router does not find the valid IOS image in flash memory,
then the system will enter ROMMON mode.
Q #41. Which of the following protocol is used for directly connected neighbour device information –
a) CDP
b) SSH
c) ICMP
d) NTP
Answers: (a) CDP.
Q #42. Which of the following command is used for show the router routing table –
a) #show ip table
b) #show ip route
c) #show routing table
d) #show ip routing table
Answers: (b) #show ip route.
Q #43. Link State Routing Protocol uses –
a) Classfull routing protocol
b) Classless routing protocol
c) Both (a) & (b)
d) None of the above
Answers: (b) Classless routing protocol.
Q #44. The AD value of EIGRP –
a) 1
b) 90
c) 110
d) 120
Answers: (b) 90.
Q #45. Which of the following protocol uses Classfull routing protocol –
a) Distance Vector Protocol
b) Link State Protocol
c) Hybrid Protocol
d) None of the above
Answers: (a) Distance Vector Protocol.
Q #46. The AD value of Static route –
a) 0
b) 1
c) 90
d) 120
Answers: (b) 1.
Q #47. Which of the following is RIP Invalid timer –
a) 30 seconds
b) 40 seconds
c) 180 seconds
d) 240 seconds
Answers: (c) 180 seconds.
Q #48. OSPF developed by –
a) IEEE
b) IETF
c) ICANN
d)IANA
Answers: (b) IETF.
Q #49. OSPF Updates are through –
a) Unicast
b) Broadcast
c) Multicast
d) Anycast
Answers: (c) Multicast.
Q #50. Which of the following table is not maintain in EIGRP –
a) Neighbour Table
b) Routing Table
c) Topology Table
d) None of the above
Answers: (d) None of the above.
