Chemical pumps

Vertical cantilever pump Type TPC-M

In PP / PE-UHMW / PVDF

 vertical setting depths up to 800 mm

 pump capacity up to 250 m3/h
 total differential head up to 60 m
 tolerant of solids
 dry run-proof

www.munsch.de
Vertical cantilever pump TPC-M

 Applications  Performance data for 50/60 Hz operation3)

Dry run-proof Type TPC vertical cantilever pumps are the Pump capacity [Q] up to 250 m3/h
solution of choice whenever it comes to pumping solids-laden Total differential head [H] up to 60 m
acids, alkalis or chemically contaminated effluents or when Motor rating [P] up to 20 kW
there is a risk of prolonged dry running. Typical applications Vertical setting depths [I] up to 800 mm
include the metal finishing industry, steel and stainless steel 3) Performance data for standard pumps; extended performance ranges on request
pickling lines, evaporation and regeneration units, flue gas
cleaning systems downstream of waste incinerators as well
as exhaust air cleaning and scrubber effluent treatment.
 Shaft seal
Labyrinth seal, optional V-ring seal
 Construction
 Flange connection
Vertical centrifugal pump with volute casing and single-
entry, single-stage radial impeller; without bottom Standard design with stub end and backing flange to DIN,
bearing; the shaft bearing is located outside the path of optionally to ANSI or JIS.
the fluid pumped.
 Drive
 Materials Three-phase AC motor, design V1 with canopy to IEC, BS or
NEMA; type of protection, flameproof enclosure and motor
Part designation
Standard material range voltage to customer specifications.
PP PE-UHMW PVDF
Pump casing PP PE-UHMW PVDF
Casing cover PP PE-UHMW PVDF  Coating
Pump shaft St Paint system for metallic pump components:
Impeller PP1) PE-UHMW1) PVDF1)
Base coat: epoxy resin primer; Top coat: PU-based finish,
Bearing lantern GGG
Secondary seals2) FPM RAL 2003, pastel orange. Total dry film thickness
Shaft protection sleeve PP PP PVDF 130 – 150 µm. Special coatings available on request.
Column pipe PP PP PVDF
Suspension pipe PP PP PVDF  Maximum allowable service pressures
Casing flange
Sole plate
PP
PP
PP
PP
PVDF
PP
and temperatures
10
1) Material combinations possible
[bar] [bar]

2) Alternatives (depending on fluid pumped): EPDM or Viton-PTFE-coated

internal pump pressure

PP Polypropylen
PE-UHMW Ultrahigh-molecular polyethylene
zulässiger Pumpeninnendruck

PVDF Polyvinylidene fluoride

5
FPM Fluoroelastomer
EPDM Ethylene propylene diene elastomer
PTFE Polytetrafluoroethylene
allowable

0
0 50 80 100 Temperature of fluid pumped [° C]
PE 90
PP
PVDF
 Arrangement Förderguttemperatur [°C]

3.1) With flange and elbow, wet-end installation 3.2) With top flange, wet-end installation 3.3) With flange and elbow, dry-end installation
  Design features
1 Flexible coupling connecting motor shaft to
pump shaft.

2 Anti-friction bearing installed in lantern. Shaft

bearing can accommodate high loads even under
1 11 part load conditions.

3  olumn pipe with 90° elbow and flange; connection

C
by a suitable pipe union allows the column pipe
and/or the discharge flange to be rotated to
virtually any position (Fig. 3.1).
2 12 Option: column pipe with flange or design to
customer's specification (Fig. 3.2)

4 Steel shaft with solid plastic protection sleeve

5 Standard setting depths 600 mm and 800 mm

3
13 6 Volute casing, casing cover and suspension pipe
made of solid plastics; with ample abrasion
allowance; maximum reliability when handling
corrosives and abrasives.

7 Solid impeller hub ensures plastics stability even

4 at high temperatures.
14
8 Impeller: closed design (Fig. 8.1); semi-open (Fig. 8.2)
or vortex (Fig. 8.3) impellers can be provided on
request.

9 Optimum hydraulic design using the latest

600-800 mm

numerical methods ensures:

5 - good suction behaviour due to low NPSH
6 requirements
- minimum mechanical vibration of
components
- long service life of anti-friction bearings
- minimized running noise.

8/9
Pump size Maximum allowable particle size [mm]
Impeller design
semi-open and closed Vortex impeller
50-32-125 8 10
50-32-160 6 10

10 50-32-200 5 10
65-40-160 8 12
65-40-200 8 12
65-50-125 10 16
80-50-200 8 16
80-65-160 10 16
80-50-250 10 16
80-50-315 10 16
100-65-200 12 16
100-65-250 12 16
125-80-200 12 18
125-100-200 15 24
Accessories/Option: Suction strainer/suction pipe
  Accessories/Options
10 Impeller is positively locked to the shaft for reverse Suction strainer
rotation protection. Suction pipe up to a length of 1600 mm
Suction strainer and suction pipe
11 Standard motor, design V1 with canopy Motor overload switch (not shown)

12 Low external height above, slim construction  Explosion protection to EU Directive

below the sole plate 94/9/EG (option)
Additional constructional measures allow the use of
13 Circular or rectangular sole plate; special sole plate the TPC in explosion hazard areas. The pump meets
geometries and sole plates with supporting flange the requirements of EU Directive No. 94/9/EG.
available on request.

14 Non-contacting Type 10 labyrinth seal

integrated into the sole plate prevents
product escaping to the atmosphere. It is
typically used in service environments
involving no environmental hazards and when
the pump tank is vented.

14) Type 10 labyrinth seal 8.2) Semi-open impeller

8.1) Closed impeller 8.3) Vortex impeller

 Performance characteristic charts

Flow rate Q [usgpm]

4,4 6 8 10 20 30 40 60 100 200 400 600 1000
200
60

40
80-50-315 100
30
65-40-250
80-50-250
20 60
125-100-200
50-32-200
Differential head H [m]

Differential head H [ft]

40
10 65-40-200 30
125-80-200
8 50-32-160
80-50-200 20
6 100-65-250
65-40-160
4 50-32-125 100-65-200
10
3

2 65-50-125
5
r = 1450 min-1
1 3
1 2 3 4 6 8 10 20 30 40 60 80 100 200 300
Flow rate Q [m3/h]

Flow rate Q [usgpm]

4,4 8 10 20 40 60 80 100 200 400
80
200
60
65-40-200

40 65-40-160
100
30 50-32-160
80
Differential head H [m]

Differential head H [ft]

65-50-125
20 60
80-65-160
50-32-125
40

10 30
8
20
6
4
3 r = 2900 min-1
10
1 2 3 4 6 8 10 20 30 40 60 80 100 120
Flow rate Q [m3/h]
Vertical cantilever pump TPC-M

MKFB0045
 Dimensions – Standard design

Pumpengröße DNd DNs a ØC D E E2 K LK p t

50-32-125 50 32 4 480 295 180 0 365 440 12,5 40
50-32-160 50 32 4 480 295 180 0 365 440 12,5 40
50-32-200 50 32 6 540 370 225 20 445 508 12,5 40
65-40-160 65 40 4 480 295 180 0 370 440 12,5 40
65-40-200 65 40 6 540 370 225 20 450 508 12,5 40
65-50-125 65 50 4 540 295 210 0 405 508 12,5 40
80-50-200 80 50 6 540 370 225 20 455 508 12,5 40
80-65-160 80 65 8 590 390 255 60 480 558 12,5 55
80-50-250 80 50 8 590 425 245 45 490 558 12,5 55
80-50-315 80 50 10 700 520 285 20 595 668 12,5 55

DNd
100-65-200 100 65 8 590 425 245 45 500 558 12,5 55

t
100-65-250 100 65 8 640 450 250 20 525 608 12,5 55
125-80-200 125 80 8 590 425 245 45 515 558 12,5 55
E2
125-100-200 125 100 10 700 460 305 60 600 668 12,5 55 LK
A = 600 or 800 (Standard) ØC

DNs
D

 Sole plate
The standard pump comes with a circular (1) or rectangular (2) sole plate;
sole plates with supporting flange (3) and special designs can be provided on request.

1) Circular sole plate 2) Rectangular sole plate 3) Circular sole plate with supporting flange

MUNSCH Chemie-Pumpen GmbH

Im Staudchen · D-56235 Ransbach-Baumbach
P.O. Box 1 42 · D-56221 Ransbach-Baumbach
Germany
Phone: +49 (0) 2623-8 98-90
Fax: +49 (0) 2623-8 98-95
Internet: http://www.munsch.de
E-Mail: [email protected]

Edition June 2011 · All technical data subject to revision · Printed on chlorine-free paper – for the sake of our environment