Copyright 2008 AIA MASTERSPEC Short Form 08/08

SECTION 087100 - DOOR HARDWARE

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes:

1. Mechanical door hardware for the following:

a. Swinging doors.
b. Sliding doors.
c. Folding doors.

2. Cylinders for door hardware specified in other Sections.

3. Electrified door hardware.

B. Products furnished, but not installed, under this Section include the products listed below.
Coordinating and scheduling the purchase and delivery of these products remain requirements
of this Section.

1. [Pivots] [thresholds] [weather stripping] [and] [lock cylinders] to be installed under

other Sections.
2. Permanent lock cores to be installed by Owner.

1.2 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Shop Drawings: Details of electrified door hardware.

C. Samples: For each exposed product and for each color and texture specified.

D. Other Action Submittals:

1. Door Hardware Schedule: Prepared by or under the supervision of Installer, detailing

fabrication and assembly of door hardware, as well as installation procedures and
diagrams. Coordinate final door hardware schedule with doors, frames, and related work
to ensure proper size, thickness, hand, function, and finish of door hardware.

a. Format: Use same scheduling sequence and format[ and use same door
numbers] as in the Contract Documents.
b. Content: Include the following information:

1) Identification number, location, hand, fire rating, size, and material of each
door and frame.
2) Locations of each door hardware set, cross-referenced to Drawings on floor
plans and to door and frame schedule.

DOOR HARDWARE 087100 - 1

Copyright 2008 AIA MASTERSPEC Short Form 08/08

3) Complete designations, including name and manufacturer, type, style,

function, size, quantity, function, and finish of each door hardware product.
4) Description of electrified door hardware sequences of operation and
interfaces with other building control systems.

2. Keying Schedule: Prepared by or under the supervision of Installer, detailing Owner's

final keying instructions for locks.

1.3 QUALITY ASSURANCE

A. Installer Qualifications: Supplier of products and an employer of workers trained and approved
by product manufacturers and an Architectural Hardware Consultant who is available during the
course of the Work to consult with Contractor, Architect, and Owner about door hardware and
keying.

B. Architectural Hardware Consultant Qualifications: A person who is experienced in providing

consulting services for door hardware installations that are comparable in material, design, and
extent to that indicated for this Project and who is currently certified by DHI as follows:

1. For door hardware, an [Architectural Hardware Consultant (AHC)] [Architectural

Hardware Consultant (AHC) who is also an Electrified Hardware Consultant
(EHC)] [Architectural Openings Consultant (AOC)].

C. Source Limitations: Provide electrified door hardware from same manufacturer as mechanical
door hardware, unless otherwise indicated. Manufacturers that perform electrical modifications
and that are listed by a testing and inspecting agency acceptable to authorities having
jurisdiction are acceptable.

D. Fire-Rated Door Assemblies: Where fire-rated door assemblies are indicated, provide door
hardware rated for use in assemblies complying with NFPA 80 that are listed and labeled by a
qualified testing agency, for fire-protection ratings indicated, based on testing at positive
pressure according to NFPA 252 or UL 10C, unless otherwise indicated.

E. Smoke- and Draft-Control Door Assemblies: Where smoke- and draft-control door assemblies
are required, provide door hardware that meet requirements of assemblies tested according to
UL 1784 and installed in compliance with NFPA 105.

1. Air Leakage Rate: Maximum air leakage of 0.3 cfm/sq. ft. (3 cu. m per minute/sq. m) at
the tested pressure differential of 0.3-inch wg (75 Pa) of water.

F. Electrified Door Hardware: Listed and labeled as defined in NFPA 70, Article 100, by a testing
agency acceptable to authorities having jurisdiction.

G. Means of Egress Doors: Latches do not require more than 15 lbf (67 N) to release the latch.
Locks do not require use of a key, tool, or special knowledge for operation.

H. Accessibility Requirements: For door hardware on doors in an accessible route, comply with
[the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA
Accessibility Guidelines] [ICC/ANSI A117.1] [HUD's "Fair Housing Accessibility
Guidelines"] [and] <Insert regulation>.

DOOR HARDWARE 087100 - 2

Copyright 2008 AIA MASTERSPEC Short Form 08/08

1. Provide operating devices that do not require tight grasping, pinching, or twisting of the
wrist and that operate with a force of not more than 5 lbf (22.2 N).
2. Comply with the following maximum opening-force requirements:

a. Interior, Non-Fire-Rated Hinged Doors: 5 lbf (22.2 N) applied perpendicular to

door.
b. Sliding or Folding Doors: 5 lbf (22.2 N) applied parallel to door at latch.
c. Fire Doors: Minimum opening force allowable by authorities having jurisdiction.

3. Bevel raised thresholds with a slope of not more than 1:2. Provide thresholds not more
than [1/2 inch (13 mm) high] [and] [3/4 inch (19 mm) high for exterior sliding doors].
4. Adjust door closer sweep periods so that, from an open position of 70 degrees, the door
will take at least 3 seconds to move to a point 3 inches (75 mm) from the latch, measured
to the leading edge of the door.

I. Keying Conference: Conduct conference at Project site to comply with requirements in

Division 01 Section "Project Management and Coordination."

1.4 DELIVERY, STORAGE, AND HANDLING

A. Deliver keys to manufacturer of key control system for subsequent delivery to Owner.

B. Deliver keys[ and permanent cores] to Owner by registered mail or overnight package service.

1.5 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or

replace components of door hardware that fail in materials or workmanship within specified
warranty period.

1. Warranty Period: [Three] <Insert number> years from date of Substantial Completion,
unless otherwise indicated.

a. [Electromagnetic] [and] [Delayed-Egress] Locks: [Five] <Insert number>

years from date of Substantial Completion.
b. Exit Devices: [Two] <Insert number> years from date of Substantial
Completion.
c. Manual Closers: [10] <Insert number> years from date of Substantial
Completion.
d. Concealed Floor Closers: [Five] [10] [25] <Insert number> years from date of
Substantial Completion.

1.6 EXTRA MATERIALS

A. Furnish extra materials that match products installed and that are packaged with protective
covering for storage and identified with labels describing contents.

1. Door Hardware: <Insert detailed descriptions and specific numbers of units>.

2. Electrical Parts: <Insert detailed descriptions and specific numbers of units>.

DOOR HARDWARE 087100 - 3

Copyright 2008 AIA MASTERSPEC Short Form 08/08

PART 2 - PRODUCTS

2.1 SCHEDULED DOOR HARDWARE

A. Provide door hardware for each door as scheduled [in Part 3 "Door Hardware Schedule"
Article] [on Drawings] to comply with requirements in this Section.

1. Door Hardware Sets: Provide quantity, item, size, finish or color indicated, and [named
manufacturers' products] [products equivalent in function and comparable in
quality to named products] [products complying with BHMA designations
referenced].
2. Sequence of Operation: Provide electrified door hardware function, sequence of
operation, and interface with other building control systems indicated.

B. Designations: Requirements for design, grade, function, finish, size, and other distinctive
qualities of each type of door hardware are indicated in Part 3 "Door Hardware Schedule"
Article. Products are identified by using door hardware designations, as follows:

1. Named Manufacturers' Products: Manufacturer and product designation are listed for
each door hardware type required for the purpose of establishing minimum requirements.
Manufacturers' names are abbreviated in Part 3 "Door Hardware Schedule" Article.
2. References to BHMA Designations: Provide products complying with these designations
and requirements for description, quality, and function.

2.2 HINGES

A. Hinges: BHMA A156.1. [ Provide template-produced hinges for hinges installed on

hollow-metal doors and hollow-metal frames.]

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Baldwin Hardware Corporation.

b. Bommer Industries, Inc.
c. Cal-Royal Products, Inc.
d. Hager Companies.
e. IVES Hardware; an Ingersoll-Rand company.
f. Lawrence Hardware Inc.
g. McKinney Products Company; an ASSA ABLOY Group company.
h. PBB, Inc.
i. Stanley Commercial Hardware; Div. of The Stanley Works.
j. <Insert manufacturer's name>.

DOOR HARDWARE 087100 - 4

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2.3 SELF-CLOSING HINGES AND PIVOTS

A. Self-Closing Hinges and Pivots: BHMA A156.17.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Baldwin Hardware Corporation.

b. Bommer Industries, Inc.
c. Cal-Royal Products, Inc.
d. Hager Companies.
e. Lawrence Hardware Inc.
f. McKinney Products Company; an ASSA ABLOY Group company.
g. PBB, Inc.
h. Stanley Commercial Hardware; Div. of The Stanley Works.
i. <Insert manufacturer's name>.

2.4 CENTER-HUNG AND OFFSET PIVOTS

A. Center-Hung and Offset Pivots: BHMA A156.4.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. DORMA Architectural Hardware; Member of The DORMA Group North

America.
b. IVES Hardware; an Ingersoll-Rand company.
c. Rixson Specialty Door Controls; an ASSA ABLOY Group company.
d. <Insert manufacturer's name>.

2.5 CONTINUOUS HINGES

A. Continuous Hinges: BHMA A156.26; minimum 0.120-inch- (3.0-mm-) thick, hinge leaves
with minimum overall width of 4 inches (102 mm); fabricated to full height of door and frame
and to template screw locations; with components finished after milling and drilling are
complete.

B. Pin-and-Barrel-Type Hinges:

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:

DOOR HARDWARE 087100 - 5

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2. Basis-of-Design Product: Subject to compliance with requirements, provide product

indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Hager Companies.
b. IVES Hardware; an Ingersoll-Rand company.
c. Lawrence Hardware Inc.
d. Markar Architectural Products, Inc.; a subsidiary of Adams Rite Manufacturing
Co.
e. McKinney Products Company; an ASSA ABLOY Group company.
f. Select Products Limited.
g. Zero International.
h. <Insert manufacturer's name>.

C. Continuous, Gear-Type Hinges: Extruded-aluminum, pinless, geared hinge leaves joined by a

continuous extruded-aluminum channel cap; with concealed, self-lubricating thrust bearings.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Bommer Industries, Inc.

b. Cal-Royal Products, Inc.
c. Hager Companies.
d. IVES Hardware; an Ingersoll-Rand company.
e. McKinney Products Company; an ASSA ABLOY Group company.
f. Select Products Limited.
g. Stanley Commercial Hardware; Div. of The Stanley Works.
h. Zero International.
i. <Insert manufacturer's name>.

2.6 MECHANICAL LOCKS AND LATCHES

A. Strikes: Provide manufacturer's standard strike for each lock bolt or latchbolt complying with
requirements indicated for applicable lock or latch and with strike box and curved lip extended
to protect frame; finished to match lock or latch.

1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by

manufacturer.
2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim.
3. Aluminum-Frame Strike Box: Manufacturer's special strike box fabricated for aluminum
framing.
4. Rabbet Front and Strike: Provide on locksets for rabbeted meeting stiles.

B. Bored Locks: BHMA A156.2; Grade [1] [2]; Series 4000.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:

DOOR HARDWARE 087100 - 6

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2. Basis-of-Design Product: Subject to compliance with requirements, provide product

indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Arrow USA; an ASSA ABLOY Group company.

b. Best Access Systems; Div. of Stanley Security Solutions, Inc.
c. Cal-Royal Products, Inc.
d. Corbin Russwin Architectural Hardware; n ASSA ABLOY Group Company.
e. Falcon Lock; An Ingersoll-Rand Company.
f. K2 Commercial Hardware; a Black & Decker Corp. company.
g. Marks USA.
h. Medeco Security Locks, Inc.; an ASSA ABLOY Group company.
i. PDQ Manufacturing.
j. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
k. Schlage Commercial Lock Division; an Ingersoll-Rand company.
l. Weiser Lock Corp.; a Black & Decker Corp. company.
m. Yale Security Inc.; an ASSA ABLOY Group company.
n. <Insert manufacturer's name>.

C. Mortise Locks: BHMA A156.13; [Operational] [Security] Grade [1] [2]; stamped steel case
with steel or brass parts; Series 1000.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Accurate Lock & Hardware Co.

b. Adams Rite Manufacturing Co.; an ASSA ABLOY Group company.
c. Arrow USA; an ASSA ABLOY Group company.
d. Best Access Systems; Div. of Stanley Security Solutions, Inc.
e. Cal-Royal Products, Inc.
f. Corbin Russwin Architectural Hardware; an ASSA ABLOY Group company.
g. Falcon Lock; an Ingersoll-Rand company.
h. Marks USA.
i. PDQ Manufacturing.
j. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
k. Schlage Commercial Lock Division; an Ingersoll-Rand company.
l. Yale Security Inc.; an ASSA ABLOY Group company.
m. <Insert manufacturer's name>.

2.7 AUXILIARY LOCKS

A. Bored Auxiliary Locks: BHMA A156.5: Grade [1] [2]; with strike that suits frame.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

DOOR HARDWARE 087100 - 7

Copyright 2008 AIA MASTERSPEC Short Form 08/08

a. Arrow USA; an ASSA ABLOY Group company.

b. Best Access Systems; Div. of Stanley Security Solutions, Inc.
c. Cal-Royal Products, Inc.
d. Falcon Lock; an Ingersoll-Rand company.
e. Hager Companies.
f. K2 Commercial Hardware; a Black & Decker Corp. company.
g. Marks USA.
h. Medeco Security Locks, Inc.; an ASSA ABLOY Group company.
i. PDQ Manufacturing.
j. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
k. Schlage Commercial Lock Division; an Ingersoll-Rand company.
l. Weiser Lock Corp.; a Black & Decker Corp. company.
m. Yale Security Inc.; an ASSA ABLOY Group company.
n. <Insert manufacturer's name>.

B. Mortise Auxiliary Locks: BHMA A156.5; Grade [1] [2]; with strike that suits frame.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Accurate Lock & Hardware Co.

b. Adams Rite Manufacturing Co.; an ASSA ABLOY Group company.
c. Arrow USA; an ASSA ABLOY Group company.
d. Best Access Systems; Div. of Stanley Security Solutions, Inc.
e. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
f. Schlage Commercial Lock Division; an Ingersoll-Rand company.
g. Yale Security Inc.; an ASSA ABLOY Group company.
h. <Insert manufacturer's name>.

C. Narrow Stile Auxiliary Locks: BHMA A156.5; Grade [1] [2]; with strike that suits frame.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Accurate Lock & Hardware Co.

b. Adams Rite Manufacturing Co.; an ASSA ABLOY Group company.
c. <Insert manufacturer's name>.

D. Push-Button Combination Locks: BHMA A156.5; [cylindrical; Grade 1] [mortise; Grade 2];
lock opens by entering a one- to five-digit code by pushing correct buttons in correct sequence;
automatically relocks when door is closed; with strike that suits frame.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:

DOOR HARDWARE 087100 - 8

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2. Basis-of-Design Product: Subject to compliance with requirements, provide product

indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Kaba Ilco Corp.; a Kaba Group company.

b. <Insert manufacturer's name>.

2.8 ELECTROMAGNETIC LOCKS

A. Electromagnetic Locks: BHMA A156.23; electrically powered; with electromagnet attached to

frame and armature plate attached to door; full-exterior or full-interior type, as required by
application indicated.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Door Controls International, Inc.

b. Dortronics Systems, Inc.
c. DynaLock Corp.
d. Rutherford Controls Int'l. Corp.
e. Schlage Commercial Lock Division; an Ingersoll-Rand company.
f. Securitron Magnalock Corporation; an ASSA ABLOY Group company.
g. Security Door Controls.
h. <Insert manufacturer's name>.

B. Delayed-Egress Electromagnetic Locks: BHMA A156.24, electrically powered, with

electromagnet attached to frame and armature plate attached to door; depressing push bar for
more than 3 seconds initiates irreversible alarm and 15-second delay for egress. When
integrated with fire alarm, fire alarm voids 15-second delay.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Door Controls International, Inc.

b. Doorguard Systems, Inc.
c. DynaLock Corp.
d. Rutherford Controls Int'l. Corp.
e. Schlage Commercial Lock Division; an Ingersoll-Rand company.
f. Securitron Magnalock Corporation; an ASSA ABLOY Group company.
g. <Insert manufacturer's name>.

DOOR HARDWARE 087100 - 9

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2.9 ELECTROMECHANICAL LOCKS

A. Electromechanical Locks: BHMA A156.25; Grade [1] [2]; motor or solenoid driven; [bored]
[mortise latchbolt] [mortise deadbolt] [mortise deadlocking latchbolt]; with strike that suits
frame.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Best Access Systems; Div. of Stanley Security Solutions, Inc.

b. Brink, R. R., Locking Systems, Inc.
c. DynaLock Corp.
d. Marks USA.
e. Rutherford Controls Int'l. Corp.
f. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
g. Schlage Commercial Lock Division; an Ingersoll-Rand company.
h. Security Door Controls.
i. Yale Security Inc.; an ASSA ABLOY Group company.
j. <Insert manufacturer's name>.

2.10 SELF-CONTAINED ELECTRONIC LOCKS

A. Self-Contained Electronic Locks: BHMA A156.25, [bored] [mortise]; with internal, battery-
powered, self-contained electronic locks; consisting of complete lockset, motor-driven lock
mechanism, and actuating device; enclosed in zinc-dichromate-plated, wrought-steel case, and
strike that suits frame. Provide key override, low-battery detection and warning, LED status
indicators, and ability to program at the lock.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Best Access Systems; Div. of Stanley Security Solutions, Inc.

b. Kaba Ilco Corp.; a Kaba Group company.
c. Marks USA.
d. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
e. Schlage Commercial Lock Division; an Ingersoll-Rand company.
f. Yale Security Inc.; an ASSA ABLOY Group company.
g. <Insert manufacturer's name>.

2.11 EXIT LOCKS AND EXIT ALARMS

A. Exit Locks and Alarms: BHMA A156.29, Grade 1.

DOOR HARDWARE 087100 - 10

Copyright 2008 AIA MASTERSPEC Short Form 08/08

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Arrow USA; an ASSA ABLOY Group company.

b. Detex Corporation.
c. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
d. <Insert manufacturer's name>.

2.12 SURFACE BOLTS

A. Surface Bolts: BHMA A156.16.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Burns Manufacturing Incorporated.

b. Don-Jo Mfg., Inc.
c. Door Controls International, Inc.
d. IVES Hardware; an Ingersoll-Rand company.
e. Trimco.
f. <Insert manufacturer's name>.

2.13 MANUAL FLUSH BOLTS

A. Manual Flush Bolts: BHMA A156.16; minimum 3/4-inch (19-mm) throw; designed for
mortising into door edge.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Adams Rite Manufacturing Co.; an ASSA ABLOY Group company.

b. Burns Manufacturing Incorporated.
c. Don-Jo Mfg., Inc.
d. Door Controls International, Inc.
e. Hiawatha, Inc.
f. IVES Hardware; an Ingersoll-Rand company.
g. Trimco.
h. <Insert manufacturer's name>.

DOOR HARDWARE 087100 - 11

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2.14 AUTOMATIC AND SELF-LATCHING FLUSH BOLTS

A. Automatic and Self-Latching Flush Bolts: BHMA A156.16; minimum 3/4-inch (19-mm)
throw; designed for mortising into door edge.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Cal-Royal Products, Inc.

b. Door Controls International, Inc.
c. IVES Hardware; an Ingersoll-Rand company.
d. Trimco.
e. <Insert manufacturer's name>.

2.15 EXIT DEVICES AND AUXILIARY ITEMS

A. Exit Devices and Auxiliary Items: BHMA A156.3.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Adams Rite Manufacturing Co.; an ASSA ABLOY Group company.

b. Arrow USA; an ASSA ABLOY Group company.
c. Cal-Royal Products, Inc.
d. Corbin Russwin Architectural Hardware; an ASSA ABLOY Group company.
e. Detex Corporation.
f. Door Controls International, Inc.
g. DORMA Architectural Hardware; Member of The DORMA Group North
America.
h. Dor-O-Matic; an Ingersoll-Rand company.
i. K2 Commercial Hardware; a Black & Decker Corp. company.
j. Monarch Exit Devices & Panic Hardware; an Ingersoll-Rand company.
k. Precision Hardware, Inc.; Division of Stanley Security Solutions, Inc.
l. Rutherford Controls Int'l. Corp.
m. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
n. Von Duprin; an Ingersoll-Rand company.
o. Yale Security Inc.; an ASSA ABLOY Group company.
p. <Insert manufacturer's name>.

2.16 LOCK CYLINDERS

A. Lock Cylinders: Tumbler type, constructed from brass or bronze, stainless steel, or nickel
silver.

DOOR HARDWARE 087100 - 12

Copyright 2008 AIA MASTERSPEC Short Form 08/08

1. Manufacturer: Same manufacturer as for locking devices.

2. Manufacturers: Subject to compliance with requirements, [provide products by one of
the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
3. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Arrow USA; an ASSA ABLOY Group company.

b. ASSA, Inc.; An ASSA ABLOY Group Company.
c. Best Access Systems; Div. of Stanley Security Solutions, Inc.
d. Corbin Russwin Architectural Hardware; an ASSA ABLOY Group company.
e. Falcon Lock; an Ingersoll-Rand company.
f. Medeco Security Locks, Inc.; an ASSA ABLOY Group company.
g. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
h. Schlage Commercial Lock Division; an Ingersoll-Rand company.
i. Yale Security Inc.; an ASSA ABLOY Group company.
j. <Insert manufacturer's name>.

B. Construction Master Keys: Provide cylinders with feature that permits voiding of construction
keys without cylinder removal. Provide 10 construction master keys.

C. Construction Cores: Provide construction cores that are replaceable by permanent cores.
Provide 10 construction master keys.

2.17 KEYING

A. Keying System: Factory registered, complying with guidelines in BHMA A156.28,

Appendix A. Incorporate decisions made in keying conference.

1. No Master Key System: Only change keys operate cylinder.

2. Master Key System: Change keys and a master key operate cylinders.
3. Grand Master Key System: Change keys, a master key, and a grand master key operate
cylinders.
4. Great-Grand Master Key System: Change keys, a master key, a grand master key, and a
great-grand master key operate cylinders.
5. Existing System:

a. Master key or grand master key locks to Owner's existing system.

b. Re-key Owner's existing master key system into new keying system.

6. Keyed Alike: Key all cylinders to same change key.

B. Keys: [Nickel silver] [Brass].

1. Stamping: Permanently inscribe each key with a visual key control number and include
the following notation:

a. Notation: ["DO NOT DUPLICATE."] [Information to be furnished by

Owner.]

DOOR HARDWARE 087100 - 13

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2. Quantity: In addition to one extra key blank for each lock, provide the following:

a. Cylinder Change Keys: Three.

b. Master Keys: Five.
c. Grand Master Keys: Five.
d. Great-Grand Master Keys: Five.

2.18 KEY CONTROL SYSTEM

A. Key Control Cabinet: BHMA A156.5; metal cabinet with baked-enamel finish; containing key-
holding hooks, labels, 2 sets of key tags with self-locking key holders, key-gathering envelopes,
and temporary and permanent markers; with key capacity of [150] <Insert number> percent of
the number of locks.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. American Key Boxes and Cabinets.

b. GE Security, Inc.
c. HPC, Inc.
d. Lund Equipment Co., Inc.
e. MMF Industries.
f. Tri Palm International.
g. <Insert manufacturer's name>.

3. Multiple-Drawer Cabinet: Cabinet with drawers equipped with key-holding panels and
key envelope storage, and progressive-type ball-bearing suspension slides. Include single
cylinder lock to lock all drawers.
4. Wall-Mounted Cabinet: Cabinet with hinged-panel door equipped with key-holding
panels and pin-tumbler cylinder door lock.
5. Portable Cabinet: Tray for mounting in file cabinet, equipped with key-holding panels,
envelopes, and cross-index system.

2.19 OPERATING TRIM

A. Operating Trim: BHMA A156.6; [aluminum] [brass] [bronze] [stainless steel], unless
otherwise indicated.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Burns Manufacturing Incorporated.

b. Don-Jo Mfg., Inc.

DOOR HARDWARE 087100 - 14

Copyright 2008 AIA MASTERSPEC Short Form 08/08

c. Forms + Surfaces.
d. Hager Companies.
e. Hiawatha, Inc.
f. IVES Hardware; an Ingersoll-Rand company.
g. Rockwood Manufacturing Company.
h. Trimco.
i. <Insert manufacturer's name>.

2.20 ACCESSORIES FOR PAIRS OF DOORS

A. Coordinators: BHMA A156.3; consisting of active-leaf, hold-open lever and inactive-leaf

release trigger; fabricated from steel with nylon-coated strike plates; with built-in, adjustable
safety release[; and with internal override].

B. Carry-Open Bars: BHMA A156.3; prevent the inactive leaf from opening before the active
leaf; provide polished brass or bronze carry-open bars with strike plate for inactive leaves of
pairs of doors unless automatic or self-latching bolts are used.

C. Astragals: BHMA A156.22.

2.21 SURFACE CLOSERS

A. Surface Closers: BHMA A156.4; rack-and-pinion hydraulic type with adjustable sweep and
latch speeds controlled by key-operated valves and forged-steel main arm. Comply with
manufacturer's written recommendations for size of door closers depending on size of door,
exposure to weather, and anticipated frequency of use. Provide factory-sized closers, adjustable
to meet field conditions and requirements for opening force.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Arrow USA; an ASSA ABLOY Group company.

b. Corbin Russwin Architectural Hardware; an ASSA ABLOY Group company.
c. DORMA Architectural Hardware; Member of The DORMA Group North
America.
d. Dor-O-Matic; an Ingersoll-Rand company.
e. K2 Commercial Hardware; a Black & Decker Corp. company.
f. LCN Closers; an Ingersoll-Rand company.
g. Norton Door Controls; an ASSA ABLOY Group company.
h. Rixson Specialty Door Controls; an ASSA ABLOY Group company.
i. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
j. Yale Security Inc.; an ASSA ABLOY Group company.
k. <Insert manufacturer's name>.

DOOR HARDWARE 087100 - 15

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2.22 CONCEALED CLOSERS

A. Concealed Closers: BHMA A156.4; rack-and-pinion hydraulic type with adjustable sweep and
latch speeds controlled by key-operated valves. Comply with manufacturer's written
recommendations for size of door closers depending on size of door, exposure to weather, and
anticipated frequency of use. Provide factory-sized closers, adjustable to meet field conditions
and requirements for opening force.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. DORMA Architectural Hardware; Member of The DORMA Group North

America.
b. LCN Closers; an Ingersoll-Rand company.
c. Norton Door Controls; an ASSA ABLOY Group company.
d. Rixson Specialty Door Controls; an ASSA ABLOY Group company.
e. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
f. <Insert manufacturer's name>.

2.23 CLOSER HOLDER RELEASE DEVICES

A. Closer Holder Release Devices: BHMA A156.15; Grade 1; closer connected with separate or
integral releasing and fire- or smoke-detecting devices. Door shall become self-closing on
interruption of signal to release device. Automatic release is activated by [smoke detection
system] [loss of power].

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Corbin Russwin Architectural Hardware; an ASSA ABLOY Group company.

b. DORMA Architectural Hardware; Member of The DORMA Group North
America.
c. LCN Closers; an Ingersoll-Rand company.
d. Norton Door Controls; an ASSA ABLOY Group company.
e. Rixson Specialty Door Controls; an ASSA ABLOY Group company.
f. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
g. <Insert manufacturer's name>.

2.24 MECHANICAL STOPS AND HOLDERS

A. Wall- and Floor-Mounted Stops: BHMA A156.16; [polished cast brass, bronze, or
aluminum] <Insert metal> base metal.

DOOR HARDWARE 087100 - 16

Copyright 2008 AIA MASTERSPEC Short Form 08/08

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Architectural Builders Hardware Mfg., Inc.

b. Baldwin Hardware Corporation.
c. Burns Manufacturing Incorporated.
d. Cal-Royal Products, Inc.
e. Don-Jo Mfg., Inc.
f. Door Controls International, Inc.
g. Hager Companies.
h. Hiawatha, Inc.
i. IVES Hardware; an Ingersoll-Rand company.
j. Rockwood Manufacturing Company.
k. Stanley Commercial Hardware; Div. of The Stanley Works.
l. Trimco.
m. <Insert manufacturer's name>.

2.25 ELECTROMAGNETIC STOPS AND HOLDERS

A. Electromagnetic Door Holders: BHMA A156.15, Grade 1; [wall-mounted electromagnetic

single] [floor-mounted electromagnet single] [floor-mounted electromagnet double] unit
with strike plate attached to swinging door; coordinated with fire detectors and interface with
fire alarm system for labeled fire-rated door assemblies.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Architectural Builders Hardware Mfg., Inc.

b. DORMA Architectural Hardware; Member of The DORMA Group North
America.
c. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
d. <Insert manufacturer's name>.

2.26 OVERHEAD STOPS AND HOLDERS

A. Overhead Stops and Holders: BHMA A156.8.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

DOOR HARDWARE 087100 - 17

Copyright 2008 AIA MASTERSPEC Short Form 08/08

a. Architectural Builders Hardware Mfg., Inc.

b. Glynn-Johnson; an Ingersoll-Rand company.
c. Rockwood Manufacturing Company.
d. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
e. <Insert manufacturer's name>.

2.27 DOOR GASKETING

A. Door Gasketing: BHMA A156.22; air leakage not to exceed 0.50 cfm per foot (0.000774 cu.
m/s per m) of crack length for gasketing other than for smoke control, as tested according to
ASTM E 283; with resilient or flexible seal strips that are easily replaceable and readily
available from stocks maintained by manufacturer.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Hager Companies.
b. M-D Building Products, Inc.
c. National Guard Products.
d. Pemko Manufacturing Co.; an ASSA ABLOY Group company.
e. Reese Enterprises, Inc.
f. Sealeze; a unit of Jason Incorporated.
g. Zero International.
h. <Insert manufacturer's name>.

2.28 THRESHOLDS

A. Thresholds: BHMA A156.21; fabricated to full width of opening indicated.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Hager Companies.
b. M-D Building Products, Inc.
c. National Guard Products.
d. Pemko Manufacturing Co.; an ASSA ABLOY Group company.
e. Reese Enterprises, Inc.
f. Rixson Specialty Door Controls; an ASSA ABLOY Group company.
g. Sealeze; a unit of Jason Incorporated.
h. Zero International.
i. <Insert manufacturer's name>.

DOOR HARDWARE 087100 - 18

Copyright 2008 AIA MASTERSPEC Short Form 08/08

2.29 SLIDING DOOR HARDWARE

A. Sliding Door Hardware: BHMA A156.14; consisting of complete sets including rails, hangers,
supports, bumpers, floor guides, and accessories indicated.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Cox, Arthur, & Sons, Inc.

b. Hager Companies.
c. Henderson, PC Inc.
d. Johnson, L. E., Products, Inc.
e. Stanley Commercial Hardware; Div. of The Stanley Works.
f. <Insert manufacturer's name>.

2.30 FOLDING DOOR HARDWARE

A. General: BHMA A156.14; complete sets including overhead rails, hangers, supports, bumpers,
floor guides, and accessories indicated.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Cox, Arthur, & Sons, Inc.

b. Hager Companies.
c. Henderson, PC Inc.
d. Johnson, L. E., Products, Inc.
e. Stanley Commercial Hardware; Div. of The Stanley Works.
f. <Insert manufacturer's name>.

2.31 METAL PROTECTIVE TRIM UNITS

A. Metal Protective Trim Units: BHMA A156.6; fabricated from 0.050-inch- (1.3-mm-) thick
[aluminum] [brass] [bronze] [stainless steel]; with manufacturer's standard machine or self-
tapping screw fasteners.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Baldwin Hardware Corporation.

DOOR HARDWARE 087100 - 19

Copyright 2008 AIA MASTERSPEC Short Form 08/08

b. Burns Manufacturing Incorporated.

c. Don-Jo Mfg., Inc.
d. Hiawatha, Inc.
e. IPC Door and Wall Protection Systems, Inc.; Div. of InPro Corporation.
f. IVES Hardware; an Ingersoll-Rand company.
g. Pawling Corporation.
h. Rockwood Manufacturing Company.
i. Trimco.
j. <Insert manufacturer's name>.

2.32 PLASTIC PROTECTION PLATES

A. Plastic Protection Plates: BHMA A156.6; fabricated with four sides beveled; [plastic
laminate; 1/8 inch (3.2 mm) thick; NEMA LD 3, Grade HGS] [rigid plastic; 0.060-inch-
(1.5-mm-) thick, PVC or acrylic-modified vinyl plastic] [acrylic; 1/8 inch (3.2 mm) thick].

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. American Floor Products Co., Inc.

b. Burns Manufacturing Incorporated.
c. Don-Jo Mfg., Inc.
d. Hiawatha, Inc.
e. IPC Door and Wall Protection Systems, Inc.; Div. of InPro Corporation.
f. Korogard Wall Protection Systems; Div. of RJF International Corporation.
g. Pawling Corporation.
h. Rockwood Manufacturing Company.
i. Tepromark International, Inc.
j. Trimco.
k. <Insert manufacturer's name>.

2.33 AUXILIARY DOOR HARDWARE

A. Auxiliary Hardware: BHMA A156.16.

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. Baldwin Hardware Corporation.

b. Cal-Royal Products, Inc.
c. Don-Jo Mfg., Inc.
d. Hager Companies.
e. Rockwood Manufacturing Company.

DOOR HARDWARE 087100 - 20

Copyright 2008 AIA MASTERSPEC Short Form 08/08

f. Stanley Commercial Hardware; Div. of The Stanley Works.

g. Trimco.
h. <Insert manufacturer's name>.

2.34 AUXILIARY ELECTRIFIED DOOR HARDWARE

A. Auxiliary Electrified Door Hardware:

1. Manufacturers: Subject to compliance with requirements, [provide products by one of

the following] [available manufacturers offering products that may be incorporated
into the Work include, but are not limited to, the following]:
2. Basis-of-Design Product: Subject to compliance with requirements, provide product
indicated on [Drawings] [schedule] or comparable product by one of the following:

a. DynaLock Corp.
b. GE Security, Inc.
c. SARGENT Manufacturing Company; an ASSA ABLOY Group company.
d. Schlage Commercial Lock Division; an Ingersoll-Rand company.
e. Securitron Magnalock Corporation; an ASSA ABLOY Group company.
f. Security Door Controls.
g. <Insert manufacturer's name>.

2.35 FABRICATION

A. Fasteners: Provide door hardware manufactured to comply with published templates prepared
for machine, wood, and sheet metal screws. Provide screws that comply with commercially
recognized industry standards for application intended, except aluminum fasteners are not
permitted. Provide Phillips flat-head screws with finished heads to match surface of door
hardware, unless otherwise indicated.

1. Concealed Fasteners: For door hardware units that are exposed when door is closed,
except for units already specified with concealed fasteners. Do not use through bolts for
installation where bolt head or nut on opposite face is exposed unless it is the only means
of securely attaching the door hardware. Where through bolts are used on hollow door
and frame construction, provide sleeves for each through bolt.
2. Fire-Rated Applications:

a. Wood or Machine Screws: For the following:

1) Hinges mortised to doors or frames[; use threaded-to-the-head wood

screws for wood doors and frames].
2) Strike plates to frames.
3) Closers to doors and frames.

b. Steel Through Bolts: For the following unless door blocking is provided:

1) Surface hinges to doors.

2) Closers to doors and frames.
3) Surface-mounted exit devices.

DOOR HARDWARE 087100 - 21

Copyright 2008 AIA MASTERSPEC Short Form 08/08

3. Spacers or Sex Bolts: For through bolting of hollow-metal doors.

4. Fasteners for Wood Doors: Comply with requirements in DHI WDHS.2, "Recommended
Fasteners for Wood Doors."
5. Gasketing Fasteners: Provide noncorrosive fasteners for exterior applications and
elsewhere as indicated.

2.36 FINISHES

A. Provide finishes complying with BHMA A156.18 as indicated in door hardware schedule.

B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable,

temporary protective covering before shipping.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Steel Doors and Frames: For surface applied door hardware, drill and tap doors and frames
according to ANSI/SDI A250.6.

B. Wood Doors: Comply with DHI WDHS.5 "Recommended Hardware Reinforcement Locations
for Mineral Core Wood Flush Doors."

C. Mounting Heights: Mount door hardware units at heights [indicated on Drawings] [to comply
with the following] unless otherwise indicated or required to comply with governing
regulations.

1. Standard Steel Doors and Frames: ANSI/SDI A250.8.

2. Custom Steel Doors and Frames: HMMA 831.
3. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for
Wood Flush Doors."

D. Install each door hardware item to comply with manufacturer's written instructions. Where
cutting and fitting are required to install door hardware onto or into surfaces that are later to be
painted or finished in another way, coordinate removal, storage, and reinstallation of surface
protective trim units with finishing work specified in Division 09 Sections. Do not install
surface-mounted items until finishes have been completed on substrates involved.

1. Set units level, plumb, and true to line and location. Adjust and reinforce attachment
substrates as necessary for proper installation and operation.
2. Drill and countersink units that are not factory prepared for anchorage fasteners. Space
fasteners and anchors according to industry standards.

E. Hinges: Install types and in quantities indicated in door hardware schedule but not fewer than
the number recommended by manufacturer for application indicated or one hinge for every 30
inches (750 mm) of door height, whichever is more stringent, unless other equivalent means of
support for door, such as spring hinges or pivots, are provided.

DOOR HARDWARE 087100 - 22

Copyright 2008 AIA MASTERSPEC Short Form 08/08

F. Intermediate Offset Pivots: Where offset pivots are indicated, provide intermediate offset
pivots in quantities indicated in door hardware schedule but not fewer than one intermediate
offset pivot per door and one additional intermediate offset pivot for every 30 inches (750 mm)
of door height greater than 90 inches (2286 mm).

G. Lock Cylinders: Install construction cores to secure building and areas during construction
period.

1. Replace construction cores with permanent cores as [indicated in keying schedule]

[directed by Owner].
2. Furnish permanent cores to Owner for installation.

H. Key Control System: Tag keys and place them on markers and hooks in key control system
cabinet, as determined by final keying schedule.

I. Boxed Power Supplies: Locate power supplies as indicated or, if not indicated, [above
accessible ceilings] [in equipment room]. Verify location with Architect.

1. Configuration: Provide [one power supply for each door opening] [least number of
power supplies required to adequately serve doors] with electrified door hardware.

J. Thresholds: Set thresholds for exterior doors and other doors indicated in full bed of sealant
complying with requirements specified in Division 07 Section "Joint Sealants."

K. Stops: Provide floor stops for doors unless wall or other type stops are indicated in door
hardware schedule. Do not mount floor stops where they will impede traffic.

L. Perimeter Gasketing: Apply to head and jamb, forming seal between door and frame.

M. Meeting Stile Gasketing: Fasten to meeting stiles, forming seal when doors are closed.

N. Door Bottoms: Apply to bottom of door, forming seal with threshold when door is closed.

O. Adjustment: Adjust and check each operating item of door hardware and each door to ensure
proper operation or function of every unit. Replace units that cannot be adjusted to operate as
intended. Adjust door control devices to compensate for final operation of heating and
ventilating equipment and to comply with referenced accessibility requirements.

3.2 FIELD QUALITY CONTROL

A. Independent Architectural Hardware Consultant: Owner will engage a qualified independent

Architectural Hardware Consultant to perform inspections and to prepare inspection reports.

3.3 DOOR HARDWARE SCHEDULE

PRIVATE tbl1
Door Hardware Set No. <Insert number>
Locations: <Insert type of door or door numbers>; each to have the following:

Qty. Item Manufacturer Product Finish

[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.

DOOR HARDWARE 087100 - 23

Copyright 2008 AIA MASTERSPEC Short Form 08/08

[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.
[#] <Insert item >. <Insert Manufacturer >. <Insert product>. <Insert finish>.

END OF SECTION 087100

DOOR HARDWARE 087100 - 24