Can I use CM67 to control my air-conditioning system?
Yes. Please refer to your installer for more information.
What if something happens to my heating system? How can I check that the CM67 is working?
See the troubleshooting guide below. If you need assistance after this, call your Heating Installer. The CM67 should only be opened or removed by a qualified professional to prevent possible injury from electric shock.
Mon Tue Wed Thu Fri Sat Sun
CM67
Programmable Thermostat
What other accessories can I buy that work with the CM67?
Honeywell provides other accessories and Add-On modules that can be used with your CM67, ask your installer for details : 1. Automatic Time Setting (ATS) Add-On Module *
Symptom Blank Display
Possible Cause No batteries Battery orientation Exhausted batteries Incorrect battery cartridge insertion
Remedy Check batteries are in the battery compartment and that the paper tab has been pulled out Check that the batteries have been installed in the correct orientation. Replace batteries Remove battery cartridge and re-insert Change the batteries as described previously Check that there is power to the system
to increase the Move the slider MAN and press TEMP temperature a few degrees above the current room temperature. The heating should come on after a few seconds. Call installer to check electrical connection between the CM67 and the boiler Call installer Call installer Remove battery cartridge and re-insert. If the symbol does not clear itself in a few minutes call the installer
Call your installer to arrange a maintenance visit. The CM67 and heating system will continue to operate as normal.
Display shows flashing
symbol
Batteries need replacing No power to system Program does not call for heat
USER GUIDE
What is a Programmable Thermostat?
Display works but heating does not switch on
The ATS module picks up a daily time signal from a transmitter in Central Europe and corrects the time on the CM67 display. So:
Trouble Shooting Guide
CM67 not connected to boiler properly
You never need to set or adjust the time There is no need to adjust the unit by -/+ 1 hour in summer / winter
since the unit does this automatically
The Honeywell CM67 is a programmable thermostat which controls your heating system so that you can have comfortable temperatures when you are at home and energy savings when you are away. It is important to understand that the CM67 is not a traditional ON/OFF controller but a HI / LOW temperature controller. This means that to program the heating to go OFF at a particular time a lower (setback) temperature setpoint is entered which you would choose to protect you and your home.
Heating switches ON/OFF too slowly or too quickly Temperature swings between too hot and too cold Display shows
symbol
CM67 not set correctly for your system CM67 not set correctly for your system Fault in the CM67 Your installer has set a scheduled maintenance alert period on your CM67 as a recommendation that your heating system should receive a routine inspection.
Your CM67 is the most accurate clock in your home so you can use
this information to set-up all your other clocks. * Not available in all Geographic Regions depending on transmitter range and home location. 2. Outside Temperature Sensor Accessory
EXT
What will the CM67 Programmable Thermostat do for me?
Attractive slim styling makes it ideal for location in any suitable room in your home Display Backlight illuminates the display when a key is pressed or the slider is moved for easier viewing in low light conditions 7 day program lets you set the CM67 to match your weekly lifestyle 6 daily independent temperature levels let you set any 6 temperatures from 5 to 30C at any time each day, to match your daily lifestyle Party button lets you temporarily maintain (or adjust) the current temperature for 1 - 23 hours. Useful when you have friends round or go out of the house for a short while Day Off button copies Sundays program into tomorrow so that you can make the CM67 follow the Sunday program if you have a day off during the week Holiday button saves energy by letting you reduce the temperature for 1 to 99 days while you are on holiday, returning to normal operation on the day you return Automatic Summer/Winter Time Change will adjust the clock automatically for 'Daylight Saving Time' Memory holds the user program indefinitely so that it is never lost even if you take the batteries out
Display shows the word 'SERVICE'
The Outside Temperature Sensor accessory can be fitted to your CM67 to display the outside temperature. By pressing the button twice, the CM67 displays the external temperature.
3. Remote Temperature Sensor Accessory
Warning. This product and its associated documentation and packaging are protected by various intellectual property rights belonging to Honeywell Inc and its subsidiaries and existing under the laws of the UK and other countries. These intellectual and property rights may include patent applications, registered designs, unregistered designs, registered trade marks, unregistered trade marks and copyrights and also include the following UK registration rights: UK patent application number 98062207.8 UK registered design numbers 2073334, 2073340 and 2073343.
Outside Temperature Sensor (optional accessory) can be fitted to the CM67 to display the outside temperature Remote Temperature Sensor (optional accessory) can be fitted to the CM67 to control the temperature from another room Optimum Start option is a program which ensures that the optimum temperature conditions are achieved at the required times as described below (not available on T6667B1069)
The Remote Temperature Sensor accessory can be fitted to your CM67 to control the temperature of another room where it is inconvenient to locate the CM67 e.g. commercial premises where the public may adjust buttons.
What is Optimum Start?
Optimum Start is an Energy Efficiency Feature that adjusts the start time of your heating system depending upon how cold it is. On cold days your Heating will be started earlier to ensure that your home is warm when you get up and on warmer days the heating system will be started later to save energy. So, if the Optimum Start Feature is used, the time / temperature settings which are entered into the CM67 are when you want to be warm by and not when you want the heating to start. (not available on T6667B1069)
42010818-003 R1
Honeywell Control Systems Ltd. Arlington Business Park Bracknell, Berkshire RG12 1EB User Help Line: 01344 656511
www.honeywelluk.com
CM67 Controls/Display Layout
The diagram below details the key button functions and display information.
Battery Low Indicator
Day Button Copy Day Button
How do I get started with the factory default temperature program?
Move the slider to AUTO. The CM67 will now control your heating using the built-in temperature program:Monday to Friday Program 1 Time 6:30 Temperature 21C 2 8:00 18C 3 12:00 21C 4 2:00 18C 5 6:00 21C 6 10:30 16C
Can I change the programmed temperature for a short time?
When the slider is in AUTO, the temperature can be adjusted temporarily or . The temperature will return to the program by pressing TEMP at the next temperature change time.
I am going on holiday for a few days. How do I save energy but ensure that the house is warm when I return?
1. Move the slider to the operating position you require on returning from holiday (AUTO or MAN) 2. Press (HOLIDAY) to display the holiday days counter and temperature. 3. Press + or - to set the holiday time (1 - 99 days). An extra flashing day marker shows you the holiday return day. or to set the holiday temperature (5C - 30C). 4. Press TEMP
The unit will control to the new temperature for the set number of days holiday. At midnight the holiday counter will be reduced by one until the selected number of days have passed. The unit will then return to normal control as set by the MAN or AUTO position. To cancel the HOLIDAY setting, press a second time.
Day Marker
Time Display
Burner on Indicator
Temperature Display
DAY 1...7
Mon
Tue
Wed
Thu
Fri
Sat
Sun
Information Enquiry Button
TEMP
How do I check the programmed temperature?
In normal operation the temperature displayed is the actual room temperature. To check the programmed temperature press and the display will show the programmed temperature with the two small arrows.
COPY DAY
Time Change Buttons
PROG
Temperature Change Buttons = increase = decrease
DATE/ PROG AUTO MAN
Saturday to Sunday Program 1 Time 8:00 Temperature 21C
2 10:00 21C
3 12:00 21C
4 2:00 21C
5 6:00 21C
6 11:00 16C
Setting Slider
OFF
Battery Compartment
Party Button
Day Off Button
Holiday Button
Program Buttons
How do I set my own temperature program for each day of the week?
1. Move the slider to PROG. The first temperature change time and setpoint for Monday will flash to indicate that they can be changed (the two small arrows are displayed only when the programmed temperature level is shown).
DATE/ PROG AUTO MAN OFF
How do I set one temperature for the whole day?
To operate as a simple thermostat with one temperature throughout the day, move the slider to MAN. Adjust the manual temperature by pressing or . The manual temperature can be set anywhere from 5C TEMP to 30C in 0.5C steps.
How can I switch the CM67 off?
Move the slider to OFF. The unit has an intelligent built-in frost protection feature, so that if the temperature falls below 5C, it will automatically switch the heating on.
CM67 Display Backlight The CM67 has a backlit display that will illuminate when a button is pressed or the slider is moved for easier viewing of the display in low light conditions. After the last button press or slider movement the backlight will remain on for 7 seconds.
I am having some friends round for tea/coffee. How can I extend my heating program for a few hours?
When the slider is in AUTO, the temperature can be adjusted temporarily by pressing the (PARTY) button. Set the party time (1 - 23 hours) by pressing + or - . Set the party temperature (5C - 30C) by pressing or . The CM67 will control to the new temperature for the set TEMP number of hours and then go back to the normal temperature program. To cancel the PARTY setting, press a second time. The button can also be used when you go out and want to reduce the temperature for a few hours to save energy.
How do change the batteries?
With no other accessories fitted and for applications other than electric heating, the batteries should last about 4 years. When the batteries need replacing, a flashing symbol will be displayed. To change the batteries: 1. Lift up the front flap to reveal the battery compartment. Open the battery compartment by inserting a coin underneath the bottom right edge of the flap and lift out. 2. Replace the used batteries with 2 new AA LR6 Alkaline Batteries and push the battery compartment firmly back into the front of the unit.
How do I set the date and time?
Move the CM67 setting slider to the DATE/ position. When you set the date and time for the first time after the batteries are inserted, the display will show:
Press the + or - buttons to set the current year (e.g. 04 = 2004)
Press the TEMP
button to set the month:
2. Press + or - to adjust the first temperature change time. Holding the button down will change the time quickly. The change time can be set in 10 minute steps from 03:00 in the morning. The change time can be adjusted up to 02:50 on the next morning, so you can maintain the evening temperature after midnight.
(Note: If you attempt to move a change time past the next change time, both times will be moved).
or to adjust the first temperature level. Holding 3. Press the TEMP the button down will change the temperature quickly. The temperature can be set in 0.5C steps from 5C to 30C.
4. Press PROG 2 to display the second temperature level and time levels for Monday. Use + or - and TEMP or to change the time and temperature.
5. The remaining temperature changes for Monday can be displayed by pressing PROG buttons 3, 4, 5 and 6 and adjusted by using + or or . (If you dont want to use all the temperature - and TEMP change times 2, 3, 4, 5 or 6, refer to the section What if I dont want to use all 6 temperature change times?).
You now have a choice to set the program for the next day:6a. Press COPY DAY to copy Mondays program into Tuesday. To set several days of the week to the same program, press COPY DAY repeatedly. 6b. Press DAY 1..7 to move the day marker to Tuesday (Day 2). The program for Tuesday can then be set as described in steps 2 to 5. Programs for Wednesday (Day 3) to Sunday (Day 7) can be set in the same way, using DAY 1..7. 7. Move the slider to AUTO when you have completed steps 6a or 6b, The CM67 will now control the room temperature at the times and temperatures you have set.
Press the + or - buttons to set the current month (e.g. 01 = January)
I have a day off work tomorrow and I am staying at home, do I have to re-program the CM67?
No, with one button press, the CM67 will remember that tomorrow is a day off. Tomorrow, the CM67 will control the temperature using Sundays program. When the slider is in AUTO, press (DAY OFF). A symbol will appear and the day marker for tomorrow will flash. This indicates that the Sunday temperature program will be followed tomorrow. Tomorrow the symbol will still appear but without the flashing day marker. The CM67 will controll tomorrows temperatures using Sundays program. To cancel tomorrows DAY OFF, press If you have 2 or more days off, press
Mon
Press the TEMP
button to set the day of the month.
Mon Tue
Press the + or - buttons to set the current day of the month.
Check if the day marker on the display indicates the correct day of the week (e.g. 4 = Thursday)
Day of the week indicator
Wed Thu Fri Sat Sun
Press TEMP
button to set the time.
twice. each night before going to bed.
Tue Wed Thu Fri Sat Sun
RESPECT YOUR ENVIRONMENT! Take care to dispose of used batteries carefully. NOTE: If you take more than one minute to change the batteries the clock may need to be reset - see How do I adjust the time?
Press the + or - buttons until the correct time is displayed. Each press of + or - button will change the time by one minute. Holding the button for a few seconds will change the time slowly then quickly.
What does 'SERVICE' on the display of my CM67 mean (optional)?
NOTE: This option only works if activated by your installer. The 'SERVICE' indicator is displayed at set intervals as a reminder that your heating system requires a routine check. Please call your installer to arrange a maintenance visit.
SERVICE
How do I adjust the time?
If you want to adjust the time at any time during normal use of the + or CM67 move the setting slider to DATE/ position then use button to adjust the time. NOTE: To access the year, month and day setting or buttons. press TEMP
DATE/ PROG AUTO MAN OFF
Display Today
Mon Tue Wed Thu Fri Sat Sun
Will my clock automatically adjust for Summer/ Winter?
The CM67 has a built-in Automatic Summer/Winter Time Change feature that will automatically adjust the clock forward or backward by one hour for Daylight Saving Time. This is carried out on the last Sunday of March and October each year. If not required this may be disabled by moving the slider to OFF position and pressing the +, - and INFO buttons together.
button (18:tC 0) to disable or the TEMP Press the TEMP (18:tC 1) to enable.
Mover the slider to AUTO to resume normal operation.
Display Tomorrow
What if I dont want to use all 6 temperature change times?
Although the CM67 has up to 6 temperature / time changes available per day (PROG 1 6), any unused settings may be deleted by holding 6 5 4 3 2 1 down the appropriate button (PROG 2 6) for 2 seconds. To reinstate any deleted setting hold down the button again for 2 seconds.
If you have a DAY OFF today and want to control the temperature using Sundays program press twice. To cancel any DAY OFF setting, press repeatedly until the symbol disappears.
The symbol will remain on the display of the CM67 until it is either reset or disabled by your installer. The CM67 and heating system will continue to operate as normal.
