Catalog No.

H-310PF
May 2016

Forged Fittings
Socket Welding and Threaded - ASME B16.11

C 2001, 2013, 2016 HY-LOK CORPORATION All rights reserved

 Forged Fittings

Information 4-7

90° Elbow Cap Tee

SWLA SWCA STA

8-10 11-13 19-21

Tee Boss Type A 45° Elbow

SWTA SWBA SLB

Boss Type R
SWBR

8-10 14 19-21

45° Elbow Reducing Insert Cross

SWLB SWRM SXA

8-10 15-16 19-21

Cross Union Street Elbows

SWXA SWUR SLC

8-10 17 22-23

Full Coupling Sockolets Full Coupling

SWFC SWOL SFC

11-13 18 24-25

Half Coupling 90° Elbow Half Coupling

SWHC SLA SHC

11-13 19-21 24-25

02
 Index

Cap Union Hex Reducing Nipple

SCA SUR H-SNR

24-25 28 32

Boss Type A Nipple Outlet Hollow Hex Plug

SBA SNOL H-SPA

Boss Type R
SBR

26 29 33

Square Head Plug Plain Nipple Outlet Hex Head Plug

H-SPD SPOL H-SPC

27 29 33

Hex Head Plug Swaged Nipple Blanking Plugs with ED-Ring for Ports
H-SPB DVSTI-GED/MED

27 30 34

Round Head Plug Thredolets Blanking Plugs with O-Ring for Ports
H-SPR SOL DVSTI

27 31 34

Hex Head Bushing Hex Nipple Seal & Condensate Pot

H-SHB H-SNA ASCP

27 32 35

Reference 36-39

03
 Forged Fittings

Scope
This catalog covers ratings, dimensions, tolerances, Table 2. Nominal Wall Thickness of Schedule 160
marking, and material requirements for forged and Double Extra Strong Pipe
fittings, both socket-welding and threaded by ASME Schedule 160 XXS
NPS
B16.11 and NORSOK Spec Class AG70, Union, mm in. mm in.
Reducing Insert and Swaged Nipples by MSS 1/8 3.15 0.124 4.83 0.190
1/4 3.68 0.145 6.05 0.238
Standard and BS3799 with some additions such as
3/8 4.01 0.158 6.40 0.252
outlets.
Combination End Fittings
Pressure Ratings The class for fittings made with combinations of
socket-welding and threaded ends shall be based on
General
the end configuration that has the lowest rating from
Fittings under this catalog shall be designated as
Table 1
class 2000, 3000, and 6000 for threaded end fittings
and class 3000, 6000, and 9000 for socket-weld end
Pressure Test Capability
fittings.
Pressure testing is not required by these products,
but the fittings of withstanding a hydrostatic test
Basic of Rating
pressure required by
The schedule of pipe corresponding to each class
applicable piping code for seamless pipe of material
designation of fitting for rating purposes is shown in
equivalent to the fitting forging and of the schedule or
Table 1.
wall thickness
Table 1. Correlation of Fittings Class With Schedule correlated with the fitting class and end connection of
Number or Wall Designation of Pipe for Table 1.
Calculation of Ratings
Class Type Pipe Used for Rating Basis
Designation of Size and Type
of Fittings Fitting Schedule No. Wall Designation
2000 80 XS
General
3000 Threaded 160 - NPS, followed by a dimensionless number, is the
6000 - XXS designation for nominal fitting size.
3000 80 XS
NPS is related to the reference nominal diameter,
6000 Socket - welding 160 -
9000 - XXS
DN, used in international standards.
Note : This table is not intended to restrict the use of pipe of The relationship is typically as follows:
thinner or thicker wall with fittings.
Actually pipe may be thinner or thicker in nominal NPS 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4
wall than that shown in Table 1. DN 6 8 10 15 20 25 32 40 50 65 80 100
When thinner pipe is used, its strength may govern the rating.
When thicker pipe is used (e.g., for mechanical strength),
the strength of the fitting govern the rating. Reducing Fitting Size
In the case of reducing tees and crosses, the size of
the largest run opening shall be given first, followed
Nonstandard Pipe Wall Thickness by the size of the opening at the opposite end of the
Since ASME B36.10M does not include Schedule run. Where the fitting is a tee, the size of the branch
160 nor Double Extra Strong thickness for NPS 1/8, is given last.
1/4, and 3/8, the values in Table 2 shall be used as Where the fitting is a cross, the largest side-outlet is
the nominal wall thicknesses of the pipe for rating the third dimension given, followed by the opening
purposes. opposite.
The line sketches, Fig. 1, illustrate how the reducing
fittings are read.

04
 Information

Fig. 1 Method of Designating Outlets of Reducing Specific Marking

Tees and Crosses The marking shall include (but is not limited to)
the following.

Manufacturer's Name or Trademark

3/4 3/4
Material Identification
1 1/4 1 1/4 1/2 Class Designation
Size
1 1/2 1 1/2

Materials
1 1/2 x 3/4 x 1 1/4 1 1/2 x 3/4 x 1 1/4 x 1/2
TEE CROSS Fittings shall be made of materials consisting of
forgings, bar, seamless pipe, or seamless tubular
products.
These materials shall conform to the requirements
Fitting Types
for the WP seamless construction materials of ASTM
Types of fittings covered by this catalog are shown in Fitting Specifications A 234, A 403, A 420, A 815, or B
Table 3, by class and size range. 366 or ASTM Forging Specifications A 105, A 182, A
Table 3. Types of Fittings by Class Designation 350, B 462, or B 564. Tees, elbows, and crosses
and NPS Size Range shall not be made from bar stock.
Socket - Welding Threaded Super duplex stainless steel can be supply according
Description Class Designation Class Designation to NORSOK M650 standard such as
3000 6000 9000 2000 3000 6000 F53 and F51.
45-deg, 90-deg elbows, 1/8-4 1/8-2 1/2-2 1/8-4 1/8-4 1/8-4
tees, crosses, 1/8-4 1/8-2 1/2-2 1/8-4 1/8-4 1/8-4
couplings, half-couplings, 1/8-4 1/8-2 1/2-2 - 1/8-4 1/8-4
and caps 1/8-4 1/8-2 1/2-2 - 1/8-4 1/8-4 Dimensions
Street elbows - - - - 1/8-2 1/8-2 General
Square, hex, round plug, - - - 1/8-4 1/8-4 1/8-4
hex, and flush bushing - - - 1/8-4 1/8-4 1/8-4
Unless otherwise noted, the dimensions without
Note : Plug, hex nipple and bushings are not identified by class tolerances for socket-welding and threaded fittings
designation. given in this catalog are nominal values and subject
They may be used for ratings up through class 6000 designation.
to the designated manufacturing tolerances.

Marking
Socket Fittings
General
Body and Socket Wall Thickness
Each fitting shall be permanently marked with the
required identification by raised lettering and/or The body and socket wall thickness of socket-
stamping, electro-etching, or vibro-tool marking on welding fittings shall be equal to or greater than the
the collar portion, raised pad, or raised boss portion values, G and C shown in this catalog.
of the forging. Cylindrical fittings shall be marked on
Socket Depth
the O.D. or end of the fitting in a location such that
the marking will not be obliterated as a result of The socket depth shall be no less than the
welding installation. The marking of bushings and minimum values, J, shown in this catalog.
plugs are not required.
Width

The forging radius shall not reduce the width of the

flat welding surface to less than the value shown in
Fig. 2.

05
 Forged Fittings

Fig. 2 Welding Gap and Minimum flat Dimensions Coincidence of Axes.

for Socket - Welding Fittings The maximum allowable variation in the alignment of
the fitting bore and socket bore axes shall be 1mm in
200mm (0.06 in. in 1 ft).
The maximum allowable variation in alignment of
Approximate 1.5 mm (0.06 in.)
recommended gap threads shall be 1 mm in 200 mm (0.06 in. in 1 ft).
before welding

Proof Testing
Proof testing for fittings made by ASME B 16.11 is
not required.

Minimum flat = 0.75 x minimum

socket wall thickness given in
Tables 1 and l - 1 (see para. 6.2.7)

Threaded Fittings.
Wall Thickness

The body or end wall thickness of threaded fittings

shall be equal to or greater than the minimum
values, G, as shown in this catalog.
Threads

All fittings with internal and external threads shall

be threaded with American National Standard
Taper Pipe Threads (ASME B1.20.1).

Collars
End collars of both socket-welding and threaded
fittings shall be such that they overlap the crotch
area as illustrated in the sketches in this catalog.

Reducing Fittings
Reducing fittings shall have the same center-to-end,
center-to-bottom of socket, band diameter, and
outside diameters as the uniform size fitting
corresponding to the largest size end connection of
the reducing fitting.

Additional Tolerances
Additional tolerances are not listed in this catalog.

Concentricity of Bores.
The socket and fitting bores shall be concentric within a
tolerance of 0.8mm (0.03 in.) for all sizes. Opposite
socket bores shall be concentric within a tolerance of
1.5mm (0.06 in.) for all sizes.

06
 Information

Ordering Information
Part Number Example
1) Socket Welding 2) Threaded

SWTA 04A - 3000 SLA 04N - 6000

Designation for Class Designation Designation for Class Designation

Name of Fittings of Fittings Name of Fittings of Fittings
(Socket Welding Tee) (90° Elbow)
Please refer to Index or Please refer to Index or
following Dimensions Table following Dimensions Table Designation for
Symbol of Threaded

Pipe Size Designation Pipe Size Designation

(Nom. Pipe Size 1/2) (Nom. Pipe Size 1/2)

Pipe Size Designations

Nom. Pipe Size 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2
Designations 01A 02A 03A 04A 06A 08A 10A 12A 16A
Note : In case of threaded, "A" is omitted.

Symbol of Threaded
R : Taper Pipe Thread (PT, JIS B0203, ISO 7/1)
G : Parallel Pipe Thread (PF, JIS B0202, ISO 228/1)
N : American National Standard Taper Pipe Thread (NPT, ANSI B1.20.1)

07
 Forged Fittings

90° Elbow Tee 45° Elbow Cross

SWLA SWTA SWLB SWXA

C B
C D
A A A B
D
C

G G

C
C C G
D

D
B

A
A

A
J

J
J

J
C

ASME B16.11
Class B Socket Body Depth
Nom. D A
Designation Socket Wall Wall of
Pipe DN Bore A 45°
of Bore Thk. Thk. socket
Fittings Size Dia. (1) Dia. (1) C (2) Min.G Min. J Elbows
11.2 7.6 3.18
1/8 6 10.8 6.1 3.18 2.41 9.5 11.0 8.0
14.6 10.0 3.78
1/4 8 14.2 8.5 3.30 3.01 9.5 11.0 8.0
18.0 13.3 4.01
3/8 10 17.6 11.8 3.50 3.20 9.5 13.5 8.0
22.2 16.6 4.67
1/2 15 21.8 15.0 4.09 3.73 9.5 15.5 11.0
27.6 21.7 4.90
3/4 20 27.2 20.2 4.27 3.91 12.5 19.0 12.5
34.3 27.4 5.69
1 25 33.9 25.9 4.98 4.55 12.5 22.5 14.0
3000
43.1 35.8 6.07
1 1/4 32 42.7 34.3 5.28 4.85 12.5 27.0 17.5
49.2 41.6 6.35
1 1/2 40 48.8 40.1 5.54 5.08 12.5 32.0 20.5
61.7 53.3 6.93
2 50 61.2 51.7 6.04 5.54 16.0 38.0 25.5
74.4 64.2 8.76
2 1/2 65 73.9 61.2 7.67 7.01 16.0 41.0 28.5
90.3 79.4 9.52
3 80 89.8 76.4 8.30 7.62 16.0 57.0 32.0
115.7 103.8 10.69
4 100 115.2 100.7 9.35 8.56 19.0 66.5 41.0
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

08
 Socket-Welding

90° Elbow Tee 45° Elbow Cross

SWLA SWTA SWLB SWXA

C B
C D
A A A B
D
C

G G

C
C C G
D

D
B

A
A

A
J

J
J

J
C

ASME B16.11
Class B Socket Body Depth
Nom. D A
Designation Socket Wall Wall of
Pipe DN Bore A 45°
of Bore Thk. Thk. socket
Fittings Size Dia. (1) Dia. (1) C (2) Min.G Min. J Elbows
11.2 4.8 3.96
1/8 6 10.8 3.2 3.43 3.15 9.5 11.0 8.0
14.6 7.1 4.60
1/4 8 14.2 5.6 4.01 3.68 9.5 13.5 8.0
18.0 9.9 5.03
3/8 10 17.6 8.4 4.37 4.01 12.5 15.5 11.0
22.2 12.5 5.97
1/2 15 21.8 11.0 5.18 4.78 9.5 19.0 12.5
6000 27.6 16.3 6.96
3/4 20 27.2 14.8 6.04 5.56 12.5 22.5 14.0
34.3 21.5 7.92
1 25 33.9 19.9 6.93 6.35 12.5 27.0 17.5
43.1 30.2 7.92
1 1/4 32 42.7 28.7 6.93 6.35 12.5 32.0 20.5
49.2 34.7 8.92
1 1/2 40 48.8 33.2 7.80 7.14 12.5 38.0 25.5
61.7 43.6 10.92
2 50 61.2 42.1 9.50 8.74 16.0 41.0 28.5
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

09
 Forged Fittings

90° Elbow Tee 45° Elbow Cross

SWLA SWTA SWLB SWXA

C B
C D
A A A B
D
C

G G

C
C C G
D

D
B

A
A

A
J

J
J

J
C

ASME B16.11
Class B Socket Body Depth
Nom. D A
Designation Socket Wall Wall of
Pipe DN Bore A 45°
of Bore Thk. Thk. socket
Fittings Size Dia. (1) Dia. (1) C (2) Min.G Min. J Elbows
22.2 7.2 9.35
1/2 15 21.8 5.6 8.18 7.47 9.5 25.5 15.5
27.6 11.8 9.78
3/4 20 27.2 10.3 8.56 7.82 12.5 28.5 19.0
34.3 16.0 11.38
1 25 33.9 14.4 9.96 9.09 12.5 32.0 20.5
9000
43.1 23.5 12.14
1 1/4 32 42.7 22.0 10.62 9.70 12.5 35.0 22.5
49.2 28.7 12.70
1 1/2 40 48.8 27.2 11.12 10.15 12.5 38.0 25.5
61.7 38.9 13.84
2 50 61.2 37.4 12.12 11.07 16.0 54.0 28.5
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

10
 Socket-Welding

Full Coupling Half Coupling Cap

SWFC SWHC SWCA

E J F J K J
C

C
D

B
D

B
ASME B16.11
Class B Socket Depth
Nom. D
Designation Socket Wall of K
Pipe DN Bore E F
of Bore Thk. socket Min.
Fittings Size Dia. (1) Dia. (1) C (2) Min. J
11.2 7.6 3.18
1/8 6 10.8 6.1 3.18 9.5 6.5 16.0 4.8
14.6 10.0 3.78
1/4 8 14.2 8.5 3.30 9.5 6.5 16.0 4.8
18.0 13.3 4.01
3/8 10 17.6 11.8 3.50 9.5 6.5 17.5 4.8
22.2 16.6 4.67
1/2 15 21.8 15.0 4.09 9.5 9.5 22.5 6.4
27.6 21.7 4.90
3/4 20 27.2 20.2 4.27 12.5 9.5 24.0 6.4
34.3 27.4 5.69
1 25 33.9 25.9 4.98 12.5 12.5 28.5 9.6
3000
43.1 35.8 6.07
1 1/4 32 42.7 34.3 5.28 12.5 12.5 30.0 9.6
49.2 41.6 6.35
1 1/2 40 48.8 40.1 5.54 12.5 12.5 32.0 11.2
61.7 53.3 6.93
2 50 61.2 51.7 6.04 16.0 19.0 41.0 12.7
74.4 64.2 8.76
2 1/2 65 73.9 61.2 7.67 16.0 19.0 43.0 15.7
90.3 79.4 9.52
3 80 89.8 76.4 8.30 16.0 19.0 44.5 19.0
115.7 103.8 10.69
4 100 115.2 100.7 9.35 19.0 19.0 48.0 22.4
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

11
 Forged Fittings

Full Coupling Half Coupling Cap

SWFC SWHC SWCA

E J F J K J
C

C
D

B
D

B
ASME B16.11
Class B Socket Depth
Nom. D
Designation Socket Wall of K
Pipe DN Bore E F
of Bore Thk. socket Min.
Fittings Size Dia. (1) Dia. (1) C (2) Min. J
11.2 4.8 3.96
1/8 6 10.8 3.2 3.43 9.5 6.5 16.0 6.4
14.6 7.1 4.60
1/4 8 14.2 5.6 4.01 9.5 6.5 16.0 6.4
18.0 9.9 5.03
3/8 10 17.6 8.4 4.37 12.5 6.5 17.5 6.4
22.2 12.5 5.97
1/2 15 21.8 11.0 5.18 9.5 9.5 22.5 7.9
27.6 16.3 6.96
6000 3/4 20 27.2 14.8 6.04 12.5 9.5 24.0 7.9
34.3 21.5 7.92
1 25 33.9 19.9 6.93 12.5 12.5 28.5 11.2
43.1 30.2 7.92
1 1/4 32 42.7 28.7 6.93 12.5 12.5 30.0 11.2
49.2 34.7 8.92
1 1/2 40 48.8 33.2 7.80 12.5 12.5 32.0 12.7
61.7 43.6 10.92
2 50 61.2 42.1 9.50 16.0 19.0 41.0 15.7
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

12
 Socket-Welding

Full Coupling Half Coupling Cap

SWFC SWHC SWCA

E J F J K J
C

C
D

B
D

B
ASME B16.11
Class B Socket Depth
Nom. D
Designation Socket Wall of K
Pipe DN Bore E F
of Bore Thk. socket Min.
Fittings Size Dia. (1) Dia. (1) C (2) Min. J
22.2 7.2 9.35
1/2 15 21.8 5.6 8.18 9.5 9.5 22.5 11.2
27.6 11.8 9.78
3/4 20 27.2 10.3 8.56 12.5 9.5 24.0 12.7
34.3 16.0 11.38
1 25 33.9 14.4 9.96 12.5 12.5 28.5 14.2
9000
43.1 23.5 12.14
1 1/4 32 42.7 22.0 10.62 12.5 12.5 30.0 14.2
49.2 28.7 12.70
1 1/2 40 48.8 27.2 11.12 12.5 12.5 32.0 15.7
61.7 38.9 13.84
2 50 61.2 37.4 12.12 16.0 19.0 41.0 19.0
Note : (1) Upper and lower values for each size are the respective maximum and minimum dimensions.
(2) Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

All dimensions are in millimeters.

13
 Forged Fittings

Boss Type A Boss Type R

SWBA SWBR

L L
J J
C

C
R
D

D
B

B
ASME B16.11
Class B Socket Depth
Nom. D
Designation Socket Wall of
Pipe Bore L
of Bore Thk. socket
Fittings Size Dia. (1) Dia. (1) C (2) Min. J
14.6 10.0 3.78
1/4 14.2 8.5 3.30 9.5 40
18.0 13.3 4.01
3/8 17.6 11.8 3.50 9.5 50
22.2 16.6 4.67
1/2 21.8 15.0 4.09 9.5 50
27.6 21.7 4.90
3/4 27.2 20.2 4.27 12.5 50
3000
34.3 27.4 5.69
1 33.9 25.9 4.98 12.5 50
43.1 35.8 6.07
1 1/4 42.7 34.3 5.28 12.5 50
49.2 41.6 6.35
1 1/2 48.8 40.1 5.54 12.5 50
61.7 53.3 6.93
2 61.2 51.7 6.04 16.0 60
1/2 22.2 12.5 5.97 9.5 50
21.8 11.0 5.18
3/4 27.6 16.3 6.96 12.5 50
27.2 14.8 6.04
1 34.3 21.5 7.92 12.5 50
33.9 19.9 6.93
6000
1 1/4 43.1 30.2 7.92 12.5 50
42.7 28.7 6.93
1 1/2 49.2 34.7 8.92 12.5 50
48.8 33.2 7.80
2 61.7 43.6 10.92 16.0 50
61.2 42.1 9.50
Note : is run pipe sizes
Example : SWBR06A-3000-R34 / S316 - 3/4" NPS CL3000 Run pipe 34.0mm O.D
Upper and lower values for each size are the respective maximum and minimum dimensions.
Average of socket wall thickness around periphery shall be no less than listed values.
The minimum values are permitted in localized areas.

Dimensions are in millimeters.

14
 Socket-Welding

Reducing Insert
SWRM SL

C
SD
SD

B
D

B
A K A K

Type.1 Type.2

Applied View Applied View

MSS SP-79
Class Socket Length
Designation Nominal Shank Laying Wall
Bore
of Pipe Type Dia. Length MIN.
Dia. Depth Min. D
Fittings Size SD A C SL
B K
3/8 x 1/4 1 14.35 10 17.15 19 9.0 3.78 14
1/2 x 1/4 2 14.35 10 21.34 21 9.0 3.78 16
1/2 x 3/8 1 17.78 10 21.34 21 12.5 4.01 16
3/4 x 1/4 2 14.35 10 26.67 18 9.0 3.78 -
3/4 x 3/8 2 17.78 10 26.67 16 12.5 4.01 -
3/4 x 1/2 1 21.97 10 26.67 22 16.0 4.67 17
1 x 3/8 2 17.78 10 33.40 18 12.5 4.01 -
1 x 1/2 2 21.97 10 33.40 16 16.0 4.67 -
1 x 3/4 1 27.31 13 33.40 24 21.0 4.90 19
3000
1 1/4 x 1/2 2 21.97 10 42.16 19 16.0 4.67 -
1 1/4 x 3/4 2 27.31 13 42.16 18 21.0 4.90 -
1 1/4 x 1 1 34.04 13 42.16 25 26.5 5.69 21
1 1/2 x 3/4 2 27.31 13 48.26 19 21.0 4.90 -
1 1/2 x 1 2 34.04 13 48.26 18 26.5 5.69 -
1 1/2 x 1 1/4 1 42.80 13 48.26 28 35.0 6.07 22
2x1 2 34.04 13 60.32 22 26.5 5.69 -
2 x 1 1/4 2 42.80 13 60.32 21 35.0 6.07 -
2 x 1 1/2 1 48.90 13 60.32 32 41.0 6.35 25

All dimensions are in millimeters.

15
 Forged Fittings

Reducing Insert
SWRM SL

C
SD
SD

B
D

B
A K A K

Type.1 Type.2

Applied View Applied View

MSS SP-79
Class Socket Length
Designation Nominal Shank Laying Wall
Bore
of Pipe Type DIA. Length MIN.
DIA. Depth Min. D
Fittings Size SD A C SL
B K
3/4 x 1/2 1 21.97 10 26.67 25 11.5 5.97 19
1 x 1/2 1 21.97 10 33.40 28 11.5 5.97 21
1 x 3/4 1 27.31 13 33.40 28 15.5 6.96 21
1 1/4 x 1/2 2 21.97 10 42.16 22 11.5 5.97 -
1 1/4 x 3/4 2 27.31 13 42.16 21 15.5 6.96 -
1 1/4 x 1 1 34.04 13 42.16 30 20.5 7.92 22
6000
1 1/2 x 3/4 2 27.31 13 48.26 25 15.5 6.96 -
1 1/2 x 1 1 34.04 13 48.26 29 20.5 7.92 25
1 1/2 x 1 1/4 1 42.80 13 48.26 35 29.5 7.92 25
2x1 2 34.04 13 60.32 25 21.0 7.92 -
2 x 1 1/4 2 42.80 13 60.32 24 29.5 7.92 -
2 x 1 1/2 1 48.90 13 60.32 47 34.0 8.90 40

All dimensions are in millimeters.

16
 Socket-Welding

Union
SWUR
L
F
G G

D
B
A
J
K E H

MSS SP-83
Depth Length
Pipe Socket Socket Water Laying Male
Nom. Nut Bearing of Width
End Bore Wall Way Flange Min. Socket Assem.
Bore Length Min.
Pipe DN Min. Flats
Min. Dia. Min. Min. Normal
Size
A B C D E F G J K L H
11.18 7.59 22.4
1/8 6 21.8 10.67 3.18 6.07 19.0 3.17 3.17 1.24 9.6 41.1 HEX. 30.0
14.61 10.01 22.4
1/4 8 21.8 14.10 3.30 8.48 19.0 3.17 3.17 1.24 9.6 41.4 HEX. 36.0
18.03 13.28 26.9
3/8 10 25.9 17.53 3.51 11.76 20.6 3.43 3.43 1.37 9.6 46.0 HEX. 41.0
22.23 16.56 26.9
1/2 15 31.2 21.72 4.09 15.04 20.6 3.68 3.68 1.50 9.6 49.0 HEX. 46.0
27.56 21.69 31.8
3/4 20 37.1 27.05 4.27 20.17 25.4 4.06 4.06 1.68 12.7 56.9 HEX. 55.0
34.29 27.41 34.3
1 25 45.5 33.78 4.98 25.88 26.2 4.57 4.44 1.85 12.7 62.0 HEX. 60.0
43.05 35.81 40.6
1 1/4 32 54.9 42.55 5.28 34.29 32.5 5.33 5.21 2.13 12.7 71.1 OCT. 75.0
49.15 41.66 42.2
1 1/2 40 61.5 48.64 5.54 40.13 34.0 5.84 5.59 2.31 12.7 76.5 OCT. 85.0
61.62 53.26 45.5
2 50 75.2 61.11 6.05 51.74 37.3 6.60 6.35 2.69 15.8 86.1 OCT. 94.0

All dimensions are in millimeters.

17
 Forged Fittings

Sockolets
SWOL
G
D
B

Root Gap

J
L
d
H

Run Pipe

Class B Depth
Nom. D
Designation Socket of
Pipe DN Bore G H d L
of Bore socket
Size Dia.
Fittings Dia. 1) Min. J
22.2 16.6
1/2 15 21.8 15.0 31.8 35.7 23.0 9.5 25.4
27.6 21.7
3/4 20 27.2 20.2 36.6 43.7 29.4 12.5 26.9
34.3 27.4
1 25 33.9 25.9 46.0 50.8 36.5 12.5 33.3
3000
43.1 35.8
1 1/4 32 42.7 34.3 55.6 65.1 44.5 12.5 33.3
49.2 41.6
1 1/2 40 48.8 40.1 61.9 72.2 50.8 12.5 34.9
61.7 53.3
2 50 61.2 51.7 74.6 88.1 65.1 16.0 39.1

1/2 15 22.2 12.5 39.7 43.7 19.1 9.5 31.8

21.8 11.0
27.6 16.3
3/4 20 27.2 14.8 45.2 49.6 25.4 12.5 36.6
34.3 21.5
1 25 33.9 19.9 57.2 61.9 33.3 12.5 39.6
6000
1 1/4 32 43.1 30.2 65.1 69.1 38.1 12.5 41.3
42.7 28.7
1 1/2 40 49.2 34.7 76.2 82.6 49.2 12.5 42.9
48.8 33.2
61.7 43.6
2 50 61.2 42.1 92.1 102.4 69.9 16.0 52.3
Note : 1) Upper and lower values for each size are the respective maximum and minimum dimensions.
2) For the CL.3000 and 6000 sockolet, inside bore, socket depth dimensions are according to ASME B16.11
3) Pipe schedule numbers and weight designations are in accordance with ASME B36.10

All dimensions are in millimeters.

18
 Threaded

90° Elbow Tee 45° Elbow Cross

SLA STA SLB SXA

A
G A A

H
H

H
A

A
L2

H H H H

ASME B16.11
Center to Min.Length
Class Center Outside Min.
Nom. to End of Thread (1)
Designation to End Diameter Wall
Pipe DN Elbows, Tees
of Size Crosses 45° Elbows of Band Thickness
Fittings C H G B L2
A
1/8 6 21 17 22 3.18 6.4 6.7

1/4 8 21 17 22 3.18 8.1 10.2

3/8 10 25 19 25 3.18 9.1 10.4

1/2 15 28 22 33 3.18 10.9 13.6

3/4 20 33 25 38 3.18 12.7 13.9

1 25 38 28 46 3.68 14.7 17.3

2000
1 1/4 32 44 33 56 3.89 17.0 18.0

1 1/2 40 51 35 62 4.01 17.8 18.4

2 50 60 43 75 4.27 19.0 19.2

2 1/2 65 76 52 92 5.61 23.6 28.9

3 80 86 64 109 5.99 25.9 30.5

4 100 106 79 146 6.55 27.7 33.0

Note : (1)Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

19
 Forged Fittings

90° Elbow Tee 45° Elbow Cross

SLA STA SLB SXA

A
G A A

H
H

H
A

A
L2

H H H H

ASME B16.11
Center to Min.Length
Class Center Outside Min.
Nom. to End of Thread (1)
Designation to End Diameter Wall
Pipe DN Elbows, Tees
of Size Crosses 45° Elbows of Band Thickness
Fittings C H G B L2
A
1/8 6 21 17 22 3.18 6.4 6.7

1/4 8 25 19 25 3.30 8.1 10.2

3/8 10 28 22 33 3.51 9.1 10.4

1/2 15 33 25 38 4.09 10.9 13.6

3/4 20 38 28 46 4.32 12.7 13.9

1 25 44 33 56 4.98 14.7 17.3

3000
1 1/4 32 51 35 62 5.28 17.0 18.0

1 1/2 40 60 43 75 5.56 17.8 18.4

2 50 64 44 84 7.14 19.0 19.2

2 1/2 65 83 52 102 7.65 23.6 28.9

3 80 95 64 121 8.84 25.9 30.5

4 100 114 79 152 11.18 27.7 33.0

Note : (1)Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

20
 Threaded

90° Elbow Tee 45° Elbow Cross

SLA STA SLB SXA

A
G A A

H
H

H
A

A
L2

H H H H

ASME B16.11
Center to Min.Length
Class Center Outside Min.
Nom. to End of Thread (1)
Designation to End Diameter Wall
Pipe DN Elbows, Tees
of Size Crosses 45° Elbows of Band Thickness
Fittings C H G B L2
A
1/8 6 25 19 25 6.35 6.4 6.7

1/4 8 28 22 33 6.60 8.1 10.2

3/8 10 33 25 38 6.98 9.1 10.4

1/2 15 38 28 46 8.15 10.9 13.6

3/4 20 44 33 56 8.53 12.7 13.9

1 25 51 35 62 9.93 14.7 17.3

6000
1 1/4 32 60 43 75 10.59 17.0 18.0

1 1/2 40 64 44 84 11.07 17.8 18.4

2 50 83 52 102 12.09 19.0 19.2

2 1/2 65 95 64 121 15.29 23.6 28.9

3 80 106 79 146 16.64 25.9 30.5

4 100 114 79 152 18.67 27.7 33.0

Note : (1)Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

21
 Forged Fittings

Street Elbows
SLC
L2

G1

H
G

L
A

ASME B16.11
Center-to Center-to Outside Min.Length Min.
Class Min. Min.
Designation Nom. -Female -Male Internal Length
Diameter Wall Wall
Pipe DN End Street End Street of Band Thickness Thickness Thread (4) Male
of Size Ells Ells Thread
Fittings H (2) G1 G (3)
A (1) J B L2 L

1/8 6 19 25 19 3.18 2.74 6.4 6.7 10

1/4 8 22 32 25 3.30 3.22 8.1 10.2 11

3/8 10 25 38 32 3.51 3.50 9.1 10.4 13

1/2 15 28 41 38 4.09 4.16 10.9 13.6 14

3000 3/4 20 35 48 44 4.32 4.88 12.7 13.9 16

1 25 44 57 51 4.98 5.56 14.7 17.3 19

1 1/4 32 51 66 62 5.28 5.56 17.0 18.0 21

1 1/2 40 54 71 70 5.56 6.25 17.8 18.4 21

2 50 64 84 84 7.14 7.64 19.0 19.2 22

Note : (1) Dimension A listed on page 21 for the appropriate fitting size may also be used at the option of the manufacturer.
(2) Dimension H listed on page 21 for the appropriate fitting size may also be used at the option of the manufacturer.
(3) Wall thickness before threading.
(4) Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

22
 Threaded

Street Elbows
SLC
L2

G1

H
G

L
A

ASME B16.11
Center-to Center-to Outside Min.Length Min.
Class Min. Min.
Designation Nom. -Female -Male Internal Length
Diameter Wall Wall
Pipe DN End Street End Street of Band Thickness Thickness Thread (4) Male
of Size Ells Ells Thread
Fittings H (2) G1 G (3)
A (1) J B L2 L

1/8 6 22 32 25 5.08 4.22 6.4 6.7 10

1/4 8 25 38 32 5.66 5.28 8.1 10.2 11

3/8 10 28 41 38 6.98 5.59 9.1 10.4 13

1/2 15 35 48 44 8.15 6.53 10.9 13.6 14

6000 3/4 20 44 57 51 8.53 6.86 12.7 13.9 16

1 25 51 66 62 9.93 7.95 14.7 17.3 19

1 1/4 32 54 71 70 10.59 8.48 17.0 18.0 21

1 1/2 40 64 84 84 11.07 8.89 17.8 18.4 21

2 50 83 105 102 12.09 9.70 19.0 19.2 22

Note : (1) Dimension A listed on page 22 for the appropriate fitting size may also be used at the option of the manufacturer.
(2) Dimension H listed on page 22 for the appropriate fitting size may also be used at the option of the manufacturer.
(3) Wall thickness before threading.
(4) Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

23
 Forged Fittings

Full Coupling Half Coupling Cap

SFC SHC SCA

L2 L2 L2
G
B B B
D

D
D
W W/2 P

ASME B16.11
Class End Wall Min.Length
Nom. End-to-End End-to-End Outside of Thread (1)
Designation Thickness
Pipe DN Coupling Coupling Diameter
of Size Min.
Fittings W P D G B L2

1/8 6 32 19 16 4.8 6.4 6.7

1/4 8 35 25 19 4.8 8.1 10.2

3/8 10 38 25 22 4.8 9.1 10.4

1/2 15 48 32 28 6.4 10.9 13.6

3/4 20 51 37 35 6.4 12.7 13.9

1 25 60 41 44 9.7 14.7 17.3

3000
1 1/4 32 67 44 57 9.7 17.0 18.0

1 1/2 40 79 44 64 11.2 17.8 18.4

2 50 86 48 76 12.7 19.0 19.2

2 1/2 65 92 60 92 15.7 23.6 28.9

3 80 108 65 108 19.0 25.9 30.5

4 100 121 68 140 22.4 27.7 33.0

General Note : (A) Class 2000 and NPS 1/8 Class 6000 couplings, half couplings, and caps are not included in this standard.
(B) The wall thickness away from the threaded ends shall meet the minimum wall thickness requirements
listed on page 21 for the appropriate NPS and Class Designation fitting.
Note : (1) Dimension B is minimum length of perfect thread. The length of useful thread(B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

24
 Threaded

Full Coupling Half Coupling Cap

SFC SHC SCA

L2 L2 L2
G
B B B
D

D
D
W W/2 P

ASME B16.11
Class End Wall Min.Length
Nom. End-to-End End-to-End Outside of Thread (1)
Designation Thickness
Pipe DN Coupling Coupling Diameter
of Size Min.
Fittings W P D G B L2

1/8 6 32 - 22 - 6.4 6.7

1/4 8 35 27 25 6.4 8.1 10.2

3/8 10 38 27 32 6.4 9.1 10.4

1/2 15 48 33 38 7.9 10.9 13.6

3/4 20 51 38 44 7.9 12.7 13.9

1 25 60 43 57 11.2 14.7 17.3

6000
1 1/4 32 67 46 64 11.2 17.0 18.0

1 1/2 40 79 48 76 12.7 17.8 18.4

2 50 86 51 92 15.7 19.0 19.2

2 1/2 65 92 64 108 19.0 23.6 28.9

3 80 108 68 127 22.4 25.9 30.5

4 100 121 75 159 28.4 27.7 33.0

General Note : (A) Class 2000 and NPS 1/8 Class 6000 couplings, half couplings, and caps are not included in this standard.
(B) The wall thickness away from the threaded ends shall meet the minimum wall thickness requirements
listed on page 22 for the appropriate NPS and Class Designation fitting.
Note : (1) Dimension B is minimum length of perfect thread. The length of useful thread(B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American National Standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

25
 Forged Fittings

Boss Type A Boss Type R

SBA SBR

L2 L2
T T
B B

D
D

L L

ASME B16.11
(1)
Fittings Nom. Outside Min. Length of Thread
Pressure Pipe DN Diameter L
Class Size D B L2

1/4 8 19 40 8.1 10.2

3/8 10 22 40 9.1 10.4
1/2 15 28 50 10.9 13.6
3/4 20 35 50 12.7 13.9
3000
1 25 44 50 14.7 17.3
1 1/4 32 57 50 17.0 18.0
1 1/2 40 64 50 17.8 18.4
2 50 76 60 19.0 19.2

1/2 15 38 50 10.9 13.6

3/4 20 44 50 12.7 13.9
1 25 57 50 14.7 17.3
6000
1 1/4 32 64 50 17.0 18.0
1 1/2 40 76 60 17.8 18.4
2 50 92 60 19.0 19.2
Note : is run pipe sizes
Example : SBR06N-3000-R34 / S316 - 3/4" NPS CL3000 Run pipe 34.0mmO.D
Dimension B is minimum length of perfect thread. The length of useful thread(B plus threads with fully formed roots and flat crests)
shall not be less than L2 (effective length of external thread) required by American national standard for pipe threads (ASME B1.20.1)

All dimensions are in millimeters.

26
 Threaded

Square Head Plug Hex Head Plug Round Head Plug Hex Head Bushing
H-SPD H-SPB H-SPR H-SHB

F
F

E
C

B A H A A G A
D

ASME B 16.11
Square Head Plugs Round Head Plugs Hex Plugs and Bushings

Nom. Min. Hex Height

Pipe Min. Min. Nom. Nom.
Length Min.
Square Width Head Width Min.
Size A Length Plug
Height Flats Diameter Flats Bushing
D H
B C E F G

1/8 10 6 7 10 35 11 - 6

1/4 11 6 10 14 41 16 3 6

3/8 13 8 11 18 41 18 4 8

1/2 14 10 14 21 44 22 5 8

3/4 16 11 16 27 44 27 6 10

1 19 13 21 33 51 36 6 10

1 1/4 21 14 24 43 51 46 7 14

1 1/2 21 16 28 48 15 50 8 16

2 22 18 32 60 64 65 9 18

2 1/2 27 19 36 73 70 75 10 19

3 28 21 41 89 70 90 10 21

4 32 25 65 114 76 115 13 25
Note : Cautionary Note Regarding Hex Bushing : Hex head bushings of one-size reduction should not be used in services where they might
be subject to harmful loads and forces other than internal pressures.

All dimensions are in millimeters.

27
 Forged Fittings

Union
SUR

F
G

G
G

NPT Thr'd

C
C

D
A
Wrench Tight Place

H-Thrd's

J
Minimum 4 Full Thrd's
Engagament Class 2A/2B Fit
L H

MSS SP-83
Pipe Socket Water Male Length
Nut Bearing Width
Nom. End Wall Way Flange Assem.
Min. Min. Flats
Pipe DN Min. Min. Bore Min. Normal
Size
A C D F G J L H
6.83
1/8 6 21.8 3.17 6.43 3.17 3.17 1.24 41.4 HEX. 30.0
9.85
1/4 8 21.8 3.30 9.45 3.17 3.17 1.24 41.4 HEX. 36.0
13.92
3/8 10 25.9 3.48 13.51 3.43 3.43 1.37 46.0 HEX. 41.0
17.47
1/2 15 31.2 4.06 17.07 3.68 3.68 1.50 49.0 HEX. 46.0
21.79
3/4 20 37.1 4.27 21.39 4.06 4.06 1.68 56.9 HEX. 55.0
28.14
1 25 45.5 4.95 27.74 4.57 4.44 1.85 62.0 HEX. 60.0
35.76
1 1/4 32 54.9 5.28 35.36 5.33 5.21 2.13 71.1 OCT. 75.0
41.61
1 1/2 40 61.5 5.54 41.20 5.84 5.59 2.31 76.5 OCT. 85.0
52.53
2 50 75.2 6.05 52.12 6.60 6.35 2.69 86.1 OCT. 94.0

All dimensions are in millimeters.

28
 Threaded

Nipple Outlet
SNOL

Nom. Run
Pipe DN Pipe L G d D
Size Size

1/2 15 36~ 3/4 88.9 23.9 14.0 21.3

3/4 20 36~ 1 88.9 30.2 18.8 26.7

d
1 25 36~1 1/4 88.9 36.6 24.4 33.3

1 1/4 32 36~1 1/2 88.9 44.5 32.5 42.2

1 1/2 40 36~ 2 88.9 50.8 38.1 48.3

D
L

2 50 36~2 1/2 88.9 65.0 49.3 60.5

G Run Pipe

Plain Nipple Outlet

SPOL

Nom. Run
Pipe DN Pipe L G d D
Size Size

1/2 15 36~3/4 88.9 23.9 14.0 21.3

3/4 20 36~ 1 88.9 30.2 18.8 26.7

d 1 25 36~1 1/4 88.9 36.6 24.4 33.3

1 1/4 32 36~1 1/2 88.9 44.5 32.5 42.2

1 1/2 40 36~ 2 88.9 50.8 38.1 48.3

D
L

2 50 36~2 1/2 88.9 65.0 49.3 60.5

Note : XX is Run Pipe Sizes

G Run Pipe

All dimensions are in millimeters.

29
 Forged Fittings

Swaged Nipple

MSS-SP-95
Large end Small end Length
Size Size

1/2 3/8 - 1/8 70

3/4 1/2 - 1/8 76
1 3/4 - 1/8 89
1 1/4 1 - 1/8 102
1 1/2 1 1/4 - 1/8 114
2 1 1/2 - 1/8 165
TBE PBE
2 1/2 2 - 1/8 178
3 2 1/2 - 1/8 203
3 1/2 3 - 1/8 203
PLE/TSE BLE/TSE 4 3 1/2 - 1/8 229
TBE : Thread both end
PBE : Plain both end
PLE/TSE : Plain large end - thread small end
BLE/TSE : Beveled large end - Thread small end
BLE/PSE : Beveled large end - Plain small end
BLE/PSE TLE/PSE
TLE/PSE : Thread large end - Plain small end

All dimensions are in millimeters.

30
 Threaded

Thredolets
SOL
A

Root Gap

L
d
B

Run Pipe

Class Nom.
Designation Pipe A B d L
of Size
Fittings

1/2 31.8 35.7 23.8 25.4

3/4 36.6 43.7 29.4 26.9

1 46.0 50.8 36.5 33.3

3000
1 1/4 55.6 65.1 44.5 33.3

1 1/2 61.9 72.2 50.8 34.9

2 74.6 88.1 65.1 38.1

1/2 39.7 43.7 19.1 31.8

3/4 45.2 49.6 25.4 36.6

1 57.2 61.9 33.3 39.6

6000
1 1/4 65.1 69.1 38.1 41.3

1 1/2 76.2 82.6 49.2 42.9

2 92.1 102.4 69.9 52.3

Note : For the CL.3000 and 6000 threadolets , inside bore, thread length dimensions are according to ASME B16.11
Pipe schedule numbers and weight designations are in accordance with ASME B36.10

All dimensions are in millimeters.

31
 Forged Fittings

Hex Nipple
H-SNA
Nom. H
Pipe L d Width
Size Across Flat

1/8 25.4 4.8 11.1

1/4 35.3 7.1 14.2

3/8 36.1 9.6 17.4

1/2 46.7 11.9 22.2

3/4 46.7 15.7 26.9

H
1 58.7 22.3 34.9

1 1/4 61.2 27.7 44.4

d

1 1/2 67.3 34.0 50.0

L 2 73.7 46.0 65.0

Hex Reducing Nipple

H-SNR
Nom. Raduced H
Pipe Nom. L d Width
Size Pipe Size Across Flat

1/4 1/8 30.7 4.8 14.2

3/8 1/8 32.0 4.8 17.4
3/8 1/4 36.1 7.1 17.4
1/2 1/8 37.2 4.8 22.2
1/2 1/4 41.7 7.1 22.2

H 1/2 3/8 41.7 9.6 22.2

3/4 1/4 41.7 7.1 26.9
3/4 1/2 46.7 11.9 26.9
1 1/4 49.3 7.1 34.9
d

1 1/2 54.1 11.9 34.9

L 1 1/4 1 61.2 22.3 44.4

1 1/2 1 65.8 22.3 50.0
2 1 71.6 22.3 70.0

All dimensions are in millimeters.

32
 Threaded

Hollow Hex Plug

H-SPA
Nom.
H
Pipe L M
(HEX.)
Size
1/8 5 7.0 0.45

1/4 6 9.0 0.70

3/8 8 10.0 0.70

1/2 10 12.0 0.90

L
H M 3/4 14 14.0 0.90

1 17 16.5 1.10

1 1/4 22 19.0 1.10

1 1/2 22 20.0 1.10

2 27 22.0 1.10

Hex Head Plug

H-SPC

ISO
H
Parallel K
(HEX.)
Thread

1/8 7.1 11.5 13.8 14.0

1/4 11.2 12.9 18.0 19.0

3/8 11.2 13.8 22.0 22.0

1/2 14.2 16.3 26.0 27.0

3/4 15.7 14.8 32.0 33.3

1 18.3 19.8 39.0 41.0

K

All dimensions are in millimeters.

33
 Forged Fittings

Blanking Plugs with *ED-Ring for Ports

DVSTI-GED/MED
ISO ISO
Metric Parallel D H L
Thread Thread
M 10 x 1 1/8 14.0 5 12.0 8

M 12 x 1.5 - 17.0 6 17.0 12

M 14 x 1.5 1/4 19.0 6 17.0 12

M 16 x 1.5 3/8 22.0 8 17.0 12

*ED-Ring
M 18 x 1.5 - 23.9 8 17.0 12

M 20 x 1.5 - 25.9 10 19.0 14

H
M 22 x 1.5 1/2 27.0 10 19.0 14
D

M 26 x 1.5 - 31.9 12 21.0 16

M 27 x 2 3/4 32.0 12 21.0 16

L
M 33 x 2 1 39.9 17 22.5 16

M 42 x 2 1 1/4 49.9 22 22.5 16

M 48 x 2 1 1/2 55.0 24 22.5 16

Blanking Plugs with O-Ring for Ports acc. to ISO 6149 / DIN3852
DVSTI
ISO
Metric D H L
Thread

M 10 x 1 13 5 14.0 10.0

M 12 x 1.5 17 6 16.5 11.5

M 14 x 1.5 19 6 16.5 11.5

M 16 x 1.5 21 6 18.0 13.0

O-Ring

M 18 x 1.5 23 8 19.5 14.5

H M 22 x 1.5 27 10 20.5 15.5

D

M 26 x 1.5 31 12 21.0 16.0

M 27 x 2 32 12 24.0 19.0

L M 33 x 2 38 17 25.5 19.0

M 42 x 2 48 22 26.0 19.5
All dimensions are in millimeters.
The Standard ED-Ring, O-Ring material is NBR(e.g. Perbunan ) however FPM(e.g. Viton ) is also available on request

34
 Socket-Welding and Threaded

Seal & Condensate Pot

1/2" NPT
TYP.
3 1 2

S.W
TYP. WELDING
PT 5

3" NPS
88.9
Materials of Constructions
No. Description Materials
WELDING 1 3" Pipe Refer. to below
RT 2 3" Cap Refer. to below
3 Half Coupling SS316 or C.S
4
4 Weld Connector SS316
5 Hex. Plug SS316 or C.S
This drawing is standard specification for part no. ACSPF4NTB
214.0

Part Number Designation

ASCP

Class Designator of Fittings

End Connection Designatior
Materials Designator
Shapes Designator
Assemblyed Seal & Condensate Pot

Shapes Designator Materials Designator

Shapes Identifier Materials Identifier

A A335 Gr. P11 1

A335 Gr. P22 2

B
A106 Gr. B 3
C
A312 Gr. TP304 4
D
A312 Gr. TP316 5
E
A312 Gr. TP304L 6
F A312 Gr. TP316L 7

End Connection Designator Class Designator of Fittings

Connection Identifier Schdule No. Identifier
1/2 NPT N SCH 40 A
1/2 PT R SCH 80 B
1/2 S.W W SCH 160 C
1/2" Hy-Lok T SCH XXS. D

All dimensions are in millimeters.

35
 Forged Fittings

Dimensions of Welded and Seamless Pipe

Carbon, Alloy and Stainless Steel
ASME B36.10M, B36.19M (in millimeters)
Nominal Nominal Wall Thickness
Outside
Pipe Size Diameter Sch 5S Sch 10S Sch 10 Sch 20 Sch 30 Sch 40S STD Sch 40 Sch 60
(in inches)
1/8 10.29 - 1.24 - - - 1.73 1.73 1.73 -
1/4 13.72 - 1.65 - - - 1.73 1.73 2.24 -
3/8 17.14 - 1.65 - - - 2.31 2.31 2.31 -
1/2 21.34 1.65 2.11 - - - 2.77 2.77 2.77 -
3/4 26.67 1.65 2.11 2.11 - - 2.87 2.87 2.87 -
1 33.40 1.65 2.77 2.77 - - 3.38 3.38 3.38 -
1 1/4 42.16 1.65 2.77 2.77 - - 3.56 3.56 3.56 -
1 1/2 48.26 1.65 2.77 2.77 - - 3.68 3.68 3.68 -
2 60.32 1.65 2.77 2.77 - - 3.91 3.91 3.91 -
2 1/2 73.02 2.11 3.05 3.05 - - 5.16 5.16 5.16 -
3 88.90 2.11 3.05 3.05 - - 5.49 5.49 5.49 -
3 1/2 101.60 2.11 3.05 3.05 - - 5.74 5.74 5.74 -
4 114.30 2.11 3.05 3.05 - - 6.02 6.02 6.02 -
5 141.30 2.77 3.40 3.40 - - 6.55 6.55 6.55 -
6 168.28 2.77 3.40 - - - 7.11 7.11 7.11 -
8 219.08 2.77 3.76 - 6.35 7.04 8.18 8.18 8.18 10.31
10 273.05 3.40 4.19 - 6.35 7.80 9.27 9.27 9.27 12.70
12 323.85 3.96 4.57 - 6.35 8.38 9.52 9.52 10.31 14.27
14 355.60 3.96 4.78 6.35 7.92 9.52 - 9.52 11.13 15.06
16 406.40 4.19 4.78 6.35 7.92 9.52 - 9.52 12.70 16.66
18 457.20 4.19 4.78 6.35 7.92 11.12 - 9.52 14.27 19.05
20 508.00 4.78 5.54 6.35 9.52 12.70 - 9.52 15.06 20.62
22 588.80 4.78 5.54 6.35 9.52 12.70 - 9.52 15.87 22.22
24 609.60 5.54 6.35 6.35 9.52 14.27 - 9.52 17.48 24.61
26 660.40 - - 7.92 12.70 - - 9.52 - -
28 711.20 - - 7.92 12.70 15.88 - 9.52 - -
30 762.00 6.35 7.92 7.92 12.70 15.88 - 9.52 - -
32 812.80 - - 7.92 12.70 15.88 - 9.52 17.48 -
34 863.60 - - 7.92 12.70 15.88 - 9.52 17.48 -
36 914.40 - - 7.92 12.70 15.88 - 9.52 19.05 -
38 965.20 - - - - - - 9.52 - -
40 1016.00 - - - - - - 9.52 - -
42 1066.80 - - - - - - 9.52 - -
44 1117.60 - - - - - - 9.52 - -
46 1168.40 - - - - - - 9.52 - -
48 1219.20 - - - - - - 9.52 - -

36
 Reference

ASME B36.10M, B36.19M (in millimeters)

Nominal Wall Thickness Nominal
Outside Pipe Size
Sch 80S XS Sch 80 Sch 100 Sch 120 Sch 140 Sch 160 XXS Diameter (in inches)
2.41 2.41 2.41 - - - - - 10.29 1/8
3.02 3.02 3.02 - - - - - 13.72 1/4
3.20 3.20 3.20 - - - - - 17.14 3/8
3.73 3.73 3.73 - - - 4.75 7.47 21.34 1/2
3.91 3.91 3.91 - - - 5.54 7.82 26.67 3/4
4.55 4.55 4.55 - - - 6.35 9.09 33.40 1
4.85 4.85 4.85 - - - 6.35 9.70 42.16 1 1/4
5.08 5.08 5.08 - - - 7.14 10.16 48.26 1 1/2
5.54 5.54 5.54 - - - 8.71 11.07 60.32 2
7.01 7.01 7.01 - - - 9.52 14.02 73.02 2 1/2
7.62 7.62 7.62 - - - 11.13 15.24 88.90 3
8.08 8.08 8.08 - - - - 16.15 101.60 3 1/2
8.56 8.56 8.56 - 11.13 - 13.49 17.12 114.30 4
9.53 9.53 9.53 - 12.70 - 15.88 19.05 141.30 5
10.97 10.97 10.97 - 14.27 - 18.24 21.95 168.28 6
12.70 12.70 12.70 15.06 18.26 20.62 23.01 22.22 219.08 8
12.70 12.70 15.06 18.26 21.44 25.40 28.58 25.40 273.05 10
12.70 12.70 17.48 21.44 25.40 28.58 33.32 25.40 323.85 12
12.70 19.05 23.83 27.79 31.75 35.71 - 355.60 14
12.70 21.44 26.19 30.96 36.52 40.46 - 406.40 16
12.70 23.82 29.36 34.92 39.67 45.24 - 457.20 18
12.70 26.19 32.54 38.10 44.45 49.99 - 508.00 20
12.70 28.58 34.92 41.28 47.62 53.98 - 558.80 22
12.70 30.93 38.89 46.02 52.37 59.51 - 609.60 24
12.70 - - - - - - 660.40 26
12.70 - - - - - - 711.20 28
12.70 - - - - - - 762.00 30
12.70 - - - - - - 812.80 32
12.70 - - - - - - 863.60 34
12.70 - - - - - - 914.40 36
12.70 - - - - - - 965.20 38
12.70 - - - - - - 1016.00 40
12.70 - - - - - - 1066.80 42
12.70 - - - - - - 1117.60 44
12.70 - - - - - - 1168.40 46
12.70 - - - - - - 1219.20 48

Dimensions are in millimeters.

37
 Forged Fittings

American National Standard Taper Pipe Threads : NPT

(ANSI : B1.20.1)
L4
(VANISH THREADS DUE TO
L2 V1
CHAMFER ON DIE)
L4 2P
L3 L1 TAPER OF THREAD 1 IN 16 MEASURED
ON DIAMETER

E3 E0 E1 E5 E3 D

Outside Pitch
Threads Pitch Diameter at Handtight Effective Thread
Nominal Dia. Engagement External
per of Beginning
Pipe of
Inch Thread of External
Size Pipe Thread Length Dia. Length Dia.
n P
D Eo L1 E1 L2 E2
1/16 0.3125 27 0.03704 0.27118 0.1600 0.28118 0.2611 0.28750
1/8 0.4050 27 0.03704 0.36351 0.1615 0.37360 0.2639 0.38000
1/4 0.5400 18 0.05556 0.47739 0.2278 0.49163 0.4018 0.50250
3/8 0.6750 18 0.05556 0.61201 0.2400 0.62701 0.4078 0.63750
1/2 0.8400 14 0.07143 0.75843 0.3200 0.77843 0.5337 0.79179
3/4 1.0500 14 0.07143 0.96768 0.3390 0.98887 0.5457 1.00179
1 1.3150 11 1/2 0.08696 1.21363 0.4000 1.23863 0.6828 1.25630
1 1/4 1.6600 11 1/2 0.08696 1.55713 0.4200 1.58338 0.7068 1.60130
1 1/2 1.9000 11 1/2 0.08696 1.79609 0.4200 1.82234 0.7235 1.84130
2 2.3750 11 1/2 0.08696 2.26902 0.4360 2.29627 0.7565 2.31630
2 1/2 2.8750 8 0.12500 2.71953 0.6820 2.76216 1.1375 2.79062
3 3.5000 8 0.12500 3.34062 0.7660 3.38850 1.2000 3.41562
3 1/2 4.0000 8 0.12500 3.83750 0.8210 3.88881 1.2500 3.91562
4 4.5000 8 0.12500 4.33438 0.8440 4.38712 1.3000 4.41562
5 5.5630 8 0.12500 5.39073 0.9370 5.44929 1.4063 5.47862
6 6.6250 8 0.12500 6.44609 0.9580 6.50597 1.5125 6.54062

Wrench Wrench Make - up Overall Nominal Perfect Basic Minor

Make - up Length for Vanish External Height Dia. at
Nominal Length
Length for Internal Thread Thread, Threads of Small
Pipe External
External (3.47 Thds) Thread End of
Size Thread Length Dia. Thread Length Dia. Pipe
V h
L2 - L1 L3 E3 L4 L5 E5 K0
1/16 0.1011 0.1111 0.26424 0.1285 0.3896 0.1870 0.28287 0.02963 0.2416
1/8 0.1024 0.1111 0.35656 0.1285 0.3924 0.1898 0.37537 0.02963 0.3339
1/4 0.1740 0.1667 0.46697 0.1928 0.5946 0.2907 0.49556 0.04444 0.4329
3/8 0.1678 0.1667 0.60160 0.1928 0.6006 0.2967 0.63056 0.04444 0.5676
1/2 0.2137 0.2143 0.74504 0.2478 0.7815 0.3909 0.78286 0.05714 0.7013
3/4 0.2067 0.2143 0.95429 0.2478 0.7935 0.4029 0.99286 0.05714 0.9105
1 0.2828 0.2609 1.19733 0.3017 0.9845 0.5089 1.24543 0.06957 1.1441
1 1/4 0.2868 0.2609 1.54083 0.3017 1.0085 0.5329 1.59043 0.06957 1.4876
1 1/2 0.3035 0.2609 1.77978 0.3017 1.0252 0.5496 1.83043 0.06957 1.7265
2 0.3205 0.2609 2.25272 0.3017 1.0582 0.5826 2.30543 0.06957 2.1995
2 1/2 0.4555 0.2500 2.70391 0.4337 1.5712 0.8875 2.77500 0.10000 2.6195
3 0.4340 0.2500 3.32500 0.4337 1.6337 0.9500 3.40000 0.10000 3.2406
3 1/2 0.4290 0.2500 3.82188 0.4337 1.6837 1.0000 3.90000 0.10000 3.7375
4 0.4560 0.2500 4.31875 0.4337 1.7337 1.0500 4.40000 0.10000 4.2344
5 0.4693 0.2500 5.37511 0.4337 1.8400 1.1563 5.46300 0.10000 5.2907
6 0.5545 0.2500 6.43047 0.4337 1.9462 1.2625 6.52500 0.10000 6.3461

38
 Reference

Taper Pipe Threads (JIS B0203 / B0202)

Basic profile of External Basic profile of Internal Fit of External Taper Thread
Taper Thread and Parallel Thread to Internal Taper Thread or
Internal Taper Thread Internal Parallel Thread

H/6
Intemal Parallel Thread

r
H/2

h/2

D1
D2
h/2

D
27.5 °
° 27.5
h

r Position of Goge
H

h
27.5 ° Plane
h/2

55° ° 27.5

h/2
r Intemal Parallel Thread
H/2

55°

D1
D2
H/6

D
P

D1
D2
D
Intemal Parallel Thread
°
90

°
90
l

D1
D2
t

D
16
25.4 25.4 a f
P= P=
n n
H = 0.960237 P H = 0.960491 P Extemal Taper
h = 0.640327 P h = 0.640327 P Thread
r = 0.137278 P r = 0.137329 P d d 2 d1

Screw Thread Basic Diameter Position of Basic Diameter Effective Thread Length(Min.)

Extemal Thread Internal Externa

Extemal Thread Internal Thread Nominal
Thread Thread
Pipe Size
The Toler- When there is When (For Reference)
Number Major Pitch Minor
of Height From the
End ance an Incomplete there
Diameter Diameter Diameter is an
Nominal
Thread Pitch of
Round- of on Basic
End of Pipe thread or Incomplete
d d2 d1
Size
per Thread
ing Pipe Diamet- Fitting More Thread
ers of Allow-
Inch Intemal Thread Internal ance Internal
Toler- Toler- Internal Internal Taper
Basic Parallel Wall
Major Pitch Minor ance ance Taper Parallel and Ouside
Length Thread thick-
Diameter Diameter Diameter Axially Axially Thread Thread Parallel Diameter
Thread ness
n p h r D D2 D1 a b c f t
R(PT) 1/8 28 0.9071 0.581 0.12 9.728 9.147 8.566 3.97 0.91 1.13 0.071 2.5 6.2 7.4 4.4 10.5 2.0
R(PT) 1/4 19 1.3368 0.856 0.18 13.157 12.301 11.445 6.01 1.34 1.67 0.104 3.7 9.4 11.0 6.7 13.8 2.3
R(PT) 3/8 19 1.3368 0.856 0.18 16.662 15.806 14.950 6.35 1.34 1.67 0.104 3.7 9.7 11.4 7.0 17.3 2.3
R(PT) 1/2 14 1.8143 1.162 0.25 20.955 19.793 18.631 8.16 1.81 2.27 0.142 5.0 12.7 15.0 9.1 21.7 2.8
R(PT) 3/4 14 1.8143 1.162 0.25 26.441 25.279 24.117 9.53 1.81 2.27 0.142 5.0 14.1 16.3 10.2 27.2 2.8
R(PT) 1 11 2.3091 1.479 0.32 33.249 31.770 30.291 10.39 2.31 2.89 0.181 6.4 16.2 19.1 11.6 34.0 3.2
R(PT) 1 1/4 11 2.3091 1.479 0.32 41.910 40.431 38.952 12.70 2.31 2.89 0.181 6.4 18.5 21.4 13.4 42.7 3.5
R(PT) 1 1/2 11 2.3091 1.479 0.32 47.803 46.324 44.845 12.70 2.31 2.89 0.181 6.4 18.5 21.4 13.4 48.6 3.5
R(PT) 2 11 2.3091 1.479 0.32 59.614 58.135 56.656 15.88 2.31 2.89 0.181 7.5 22.8 25.7 16.9 60.5 3.8
R(PT) 2 1/2 11 2.3091 1.479 0.32 75.184 73.705 72.226 17.46 3.46 3.46 0.216 9.2 26.7 30.1 18.6 76.3 4.2
R(PT) 3 11 2.3091 1.479 0.32 87.884 86.405 84.926 20.64 3.46 3.46 0.216 9.2 29.8 33.3 21.1 89.1 4.2
R(PT) 3 1/2 11 2.3091 1.479 0.32 100.330 98.851 97.372 22.23 3.46 3.46 0.216 9.2 31.4 34.9 22.4 101.6 4.2
R(PT) 4 11 2.3091 1.479 0.32 113.030 111.551 110.072 25.40 3.46 3.46 0.216 10.4 35.8 39.3 25.9 114.3 4.5
R(PT) 5 11 2.3091 1.479 0.32 138.430 136.951 135.472 28.58 3.46 3.46 0.216 11.5 40.1 43.5 29.3 139.8 4.5
R(PT) 6 11 2.3091 1.479 0.32 163.830 162.351 160.872 28.58 3.46 3.46 0.216 11.5 40.1 43.5 29.4 165.2 5.0

39
 www.hy-lok.com

Distributed by :