AMS5675 REV.

H
AEROSPACE
MATERIAL SPECIFICATION Issued 1959-01
Cancelled 2007-04
Revised 2014-12

Superseding AMS5675G

(R) Nickel Alloy, Corrosion and Heat Resistant, Welding Wire

70Ni - 2.5Mn - 15.5Cr - 3.0Ti - 7.0Fe
(Composition similar to UNS N07092)

RATIONALE

AMS5675H has been updated to incorporate the standard quality requirements of AMS materials as the ordering
requirements for AWS specified wire, and is a Five Year Review and update of this specification.

1. SCOPE

1.1 Form

This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire.

1.2 Applications

This wire has been used typically as filler metal for gas-metal-arc or gas-tungsten-arc welding of parts fabricated from
alloys of dissimilar composition, but usage is not limited to such application.

2. APPLICABLE DOCUMENTS

The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the
extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue
is specified. When the referenced document has been cancelled and no superseding document has been specified, the
last published issue of that document shall apply.

2.1 SAE Publications

Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA
and Canada) or 724-776-4970 (outside USA), www.sae.org.

AMS2813 Packaging and Marking of Packages of Welding Wire, Standard Method

AMS2814 Packaging and Marking of Packages of Welding Wire, Premium Quality

AMS2816 Identification, Welding Wire, Tab Marking Method

AMS2819 Identification, Welding Wire, Direct Color Code System

ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire

__________________________________________________________________________________________________________________________________________
SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is
entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and
suggestions.
Copyright © 2014 SAE International
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) SAE values your input. To provide feedback
Tel: +1 724-776-4970 (outside USA) on this Technical Report, please visit
Fax: 724-776-0790 http://www.sae.org/technical/standards/AMS5675H
Email: [email protected]
SAE WEB ADDRESS: http://www.sae.org
SAE INTERNATIONAL AMS5675H Page 2 of 3

2.2 AWS Publications

Available from American Welding Society, 8669 NW 36 Street, #130, Miami, FL 33166,-6672, Tel: 1-800-443-9353 or
305-443-9353, www.aws.org.

AWS A5.01 Welding Consumables— Procurement of Filler Metals and Fluxes

AWS A5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods

3. TECHNICAL REQUIREMENTS

3.1 Wire shall meet the technical requirements of AWS A5.14 ERNiCrFe-6.

3.2 Sizes and Tolerances

Wire shall be supplied in the sizes and to the tolerances specified in AWS A5.14. Smaller diameter wires when ordered
shall be supplied in sizes and tolerances shown in 3.2.1.

3.2.1 Diameter

Shall be as shown in Table 2.

TABLE 2A - Sizes and Diameter Tolerances, Inch/Pound Units

Form Nominal Diameter Tolerance Tolerance

Inch Inch Inch
plus minus
Cut Lengths 0.030, 0.035, 0.045 0.001 0.002

Spools 0.007, 0.010, 0.015 0.0005 0.0005

TABLE 2B - Sizes and Diameter Tolerances, SI Units

Nominal Diameter Tolerance Tolerance

Form Millimeters Millimeter Millimeter
plus minus
Cut Lengths 0.76, 0.89, 1.14 0.025 0.05

Spools 0.18, 0.25, 0.38 0.013 0.013

4. QUALITY ASSURANCE PROVISIONS

4.1 Responsibility for Inspection

The vendor of wire shall supply all samples for vendor's tests and shall be responsible for the performance of all required
tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that
the wire conforms to specified requirements.

4.2 Classification of Tests

4.2.1 Acceptance Tests

Composition , sizes and tolerances (3.2) , and alloy verification (5.1) are acceptance tests and shall be performed on each
heat or lot as applicable.

4.3 Sampling and Testing

Shall be in accordance with AWS A5.01 S3, testing schedule 5 or J.

SAE INTERNATIONAL AMS5675H Page 3 of 3

4.4 Reports

The vendor of wire shall furnish with each shipment a report showing the results of tests for chemical composition of each
heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order
number, heat and lot numbers, AMS5675H, nominal size, and quantity.

4.5 Resampling and Retesting

Shall be in accordance with AMS2371.

5. PREPARATION FOR DELIVERY

5.1 Alloy Verification

5.1.1 Wire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser and
vendor. The alloy verification methods of ARP4926 are recommended.

5.1.2 An 8-inch (203-mm) length of wire shall be made accessible at both ends of each spool for alloy verification.

5.2 Identification

Shall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser.

5.3 Packaging and Marking

Shall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser.

6. ACKNOWLEDGMENT

A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase
orders.

7. REJECTIONS

Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.

8. NOTES

8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical
revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of
the document title indicates a complete revision of the document, including technical revisions. Change bars and (R)
are not used in original publications, nor in documents that contain editorial changes only.

8.2 Terms used in AMS are clarified in ARP1917.

8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and
properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units
and are presented only for information.

8.4 Purchase documents should specify not less than the following:

AMS5675H
Size and form (spools or cut lengths) of wire desired
Length of cut lengths or weight of spools desired
Quantity of wire desired.

PREPARED BY AMS COMMITTEE “F”