Epiroc
Advanced Drill Control Settings
COP 3060ME, MEX Ver. B
SmartRoc T45-10
Caution! Make sure the hydraulic oil have reached normal working temperature before adjusting the base
settings. The rock drill pressures in this document refers to the pressure at the rock drill intakes. The
hydraulic pressure at the operator panel is usually 5-10 bar above the pressure at the rock drill.
Rock drill / Drill rig
Rock Drill Serial No: Shank adapter:
Drill Rig Type: Drill Rig Serial No.:
Hydraulic oil grade: Lubrication oil type:
Rock drill settings
Accumulator pressures Base setting: Max setting: Actual setting:
HP accumulator 85 100 bar
LP accumulator 2 2 bar
Damper Setting: Actual setting:
Dampening pressure idling (measured at rock drill): 25 bar
Dampening pressure idling (at operator’s panel): 30 bar
Damper pressure during drilling @ different percussion pressure
Stroke setting ☐ Stroke 1 ☐ Stroke 2 Actual pressure:
@ Percussion pressure 180 200 220 240 180 195 210 225 bar
Damper pressure ~75 ~80 ~85 ~90 ~80 ~85 ~90 ~95 bar
Percussion
Stroke ☐1 or ☐2 (base setting is 2)
Stroke 1 setting (low impact energy) Base: Min: Max: Actual setting:
Percussion pressure, Collaring 130 130 150 bar
Percussion pressure, Drilling 220 ~26kw 200 (44Hz) 240 (48Hz) bar
Stroke 2 setting (high impact energy) Base: Min: Max: Actual setting:
Percussion pressure, Collaring 130 120 140 bar
Percussion pressure, Drilling 200 ~25kw 180 (36Hz) 225 (40Hz) bar
Feed
Pressure setting Base: Min: Max: Actual setting:
Collaring 50 40 60 bar
Drilling ~75* 60 115 bar
Max feed, Drilling 115 bar
Min feed, Drilling 30 bar
TIS0004230-001en
1(2)
Rotation Obs: Rotation speed calculated with 5/6 movement of peripheral button diameter
Drill bit diameter ☐ 89 ☐ 102 ☐ 115 ☐ 127 ☐ 140 mm
Stroke 1 settings Base: Base: Base: Base: Base: Actual setting:
@ Percussion pressure 180 200 190 210 210 230 220 240 220 240 bar
Rotation speed approx. 98 103 86 90 90 94 83 87 82 85 rpm
Stroke 2 settings Base: Base: Base: Base: Base: Actual setting:
@ Percussion pressure 180 200 190 210 200 225 200 225 200 225 bar
Rotation speed approx. 84 89 74 78 76 80 69 72 67 71 rpm
Drill Control:
DPCI Base: Min: Max: Actual setting:
Damper pressure, low percussion 65 40 70 bar
Damper pressure, high percussion 80 70 90 bar
Damper pressure, boost 100 90 110 bar
Percussion pressure, boost 10 10 20 bar
Min damper pressure 45 bar
Max damper pressure 130 120 140 bar
RPCF
Rotation motor: ☐ 250cc ☐ 315cc ☐ 400cc Actual setting:
Rotation pressure, Drilling 75 65 55 bar
Pressure increase, Jamming +25 +25 +25 bar
Pressure decrease, Free -10 -10 -10 bar
FSCI** Obs: FSCI settings based on base settings for percussion and feed
Drill bit diameter ☐ 90 ☐ 105 ☐ 115 ☐ 127 ☐ 140 mm
Setting Base: Base: Base: Base: Base: Actual setting:
Limits perc High Low High Low High Low High Low High Low High Low
Hard 1,55 2,05 1,35 1,85 1,15 1,65 0,95 1,45 0,75 1,25 m/min
Medium 1,95 2,45 1,75 2,25 1,55 2,05 1,35 1,85 1,15 1,65 m/min
Soft 2,35 2,85 2,15 3,65 1,95 2,45 1,75 2,25 1,55 2,05 m/min
Other settings
Drill rig Base: Actual setting:
Air flushing pressure 12 bar
Air pressure at rock drill 2,5-3 bar
ECL-lubricant pulses/minute 15 pulses/min
Data collected
Date:
Percussion hours (Drill Rig):
Collected by:……………………………………………… Function:………………………………………....…
* Adjust the feed force to keep minimum 80 bar damper pressure in high percussion drilling.
** FSCI need adjustment according to actual ground condition.
TIS0004230-001en
2(2)
