Main power switch.

INSTRUCTIONS FOR USE To be changed more than once: At the bottom of the relay box, the SE unit and the
smaller types of steam generators is a main power switch that disconnects the heater
CC 10 entirely from the electrical supply. This main switch should only be used if the sauna will
not be used for a longer period, such as several weeks. To be changed more than once:
The memory function must be reset each time the power is interrupted.
The thermometer in the sauna/steam bath should be placed at such a height that the
temperature corresponds exactly to the numbers in the panel of the CC 50.
10

SETTINGS
9 CC 10
8
7
6
5
5
4
3
2
1
4 CC 50, all models

Setting the bathing temperature.

Press TEMP – the previous temperature is displayed. Use the up and down arrows (
1 2 3
) to change the temperature.
Manual on/off.
Functions. Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out). If
1 = setting scale. 2 = time settings. 3 = temperature settings. 4 = on. 5 = off.
you forget to switch off the generator manually, it switches off automatically after 3 or 12
Temperature setting. hours - depending on the type of control panel.
(The heater must be switched on) Timer settings.
Press TEMP – the previous temperature setting is displayed.
(The sauna must be switched off)
The numbers indicate a rising temperature scale. Experiment to find the temperature
Press TIME (the hour digits blink) – set the number of hours until you want to use the
that suits you best. Begin for example by turning the thermostat dial to position 4. If you
later find that you would prefer a higher or lower temperature, adjust the dial up or down
sauna using the up and down arrows (
).
Press TIME (the minute digits blink) – set the number of minutes until you want to use
until you find the ideal bathing temperature for you (usually 70-90°C (158-194°F) for
traditional dry and wet sauna baths, 40-45°C (104-113°F) for steam saunas and herb the sauna using the up and down arrows (
).
saunas). (Important: The hour or minute digits must be blinking before you press ON).
Press ON – the on time is activated and a red LED blinks until the sauna automatically
Manual on/off. starts after the pre-set time. The heater switches off automatically after 3 or 12 hours –
Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out). depending on the type of control panel.
A memory function automatically sets the previous temperature. You can switch off the sauna manually at any time by pressing OFF.
Press TEMP – to change the pre-set temperature.
The built-in timer automatically switches the sauna heater/steam generator off after Changing the type of panel (Factory settings = Test no. 50),
3 hours. If you want to switch it off earlier than that, press OFF. To extend the sauna
time, press ON. 1. Connect the voltage.

Timer settings.


2. Press and at the same time for approx. 6 sek (max. 60 sek. after the
voltage is connected).
(The heater must be switched off)
The numbers in this case represent the timer times (= the number of hours until the 3. Change the type of panel according to the scheme with and , approve

heater automatically switches on). To set the timer: with TEMP.
Press TIME – use the arrow keys to select the desired pre-set time, 1–10 hours.
Press ON – the timer is activated and the time indicator blinks during the pre-set time Test no. Test no.
period. Once the heater switches itself on, it remains on for 3 hours, after which it Panel type Description
* **
automatically switches itself off. If you want to switch it off earlier than that, just press
OFF. To extend your sauna time, press ON. CC50-3B 50 50.A Sauna 110°C, 3 h running time

Main power switch. CC50-12B 51 51.A Sauna 110°C, 12 h running time

To be changed more than once: At the bottom of the relay box, the SE unit and the CC50-3S 53 53.A Steam 55°C, 3 h running time
smaller types of steam generators is a main power switch that disconnects the heater
CC50-12S 54 54.A Steam 55°C, 12 h running time
entirely from the electrical supply. This main switch should only be used if the sauna will
not be used for a longer period, such as several weeks. To be changed more than once: CC50-1S 15 15.A Steam 55°C, 1 h running time
The memory function must be reset each time the power is interrupted. CC50-1B 18 18.A Sauna 110°C, 1 h running time

INSTRUCTIONS FOR USE

CC50-24B 58 58.A Sauna 110°C, 24 h running time
CC50-0B 59 59.A Sauna 110°C, ON/OFF

CC 50 CC50-24S 68 68.A Steam 55°C, 24 h running time

CC50-0S 69 69.A Steam 55°C, ON/OFF

* Settings at ev. use of extern switch with impulse function.

** Settings at ev. use of extern switch with ON/OFF function.

00 Code lock to prevent settings from being changed.

First program as ”Settings”, press on the down arrow ( ), hold it down and press TEMP
and TIME at the same time. The code lock, which prevents changing of settings, is now
6

activated. To return to unlocked mode, press the down arrow ( ), hold it down and
press OFF at the same time.
Code lock that prevents changing of the temperature setting.
First program as ”Settings”, press TIME, hold it down and press TEMP and LIGHT at
the same time. The code lock, which prevents changing of the temperature settings, is


now activated. To return to unlocked mode, press the down arrow ( ), hold it down and
press OFF at the same time.
1 2 3 4
Functions.
1 = lighting. 2 = on/off. 3 = temperature setting. 4 = time setting. 5 = reduce temperature/time.
6 = increase temperature/time. 7 = display.

Lighting.
Lights automatically when the facility starts and switches off automatically when the
facility shuts down. You can also switch the lighting on or off manually by pressing
LIGHT.

5
 Use the up and down arrow keys (

) to set the day. Move to the hour setting by
INSTRUCTIONS FOR USE 
pressing the right arrow ( ). Set the hour using the up and down arrows
(

), and shift to minutes with the right arrow ( ). Change the minutes using the up
CC 100 and down arrows ( ).

Press MENU to exit. ( ).

12 11 10 SETTINGS
Note: CC 100-3B/3S/12B/12S only

Mo n d a y 1 0 : 0 0 :0 0 Note: for all settings, the Tylarium should be switched OFF. To be changed
CC100 i s off
P r e s s O N t o s ta r t 9 more than once: However, temperature and humidity settings can be changed
P re s s IN FO fo r h e lp
when the Tylarium is ON.
MANUAL ON/OFF.
Note: CC 100-3B/3S/12B/12S only
Setting the bathing temperature.
Press TEMP – the previous temperature is displayed. Use the up and down arrows (

) to change the temperature.
Manual on/off.
Press ON to switch the facility on. Press OFF to switch it off. If you forget to switch it off
1 2 3 4 5 6 manually, the generator automatically switches off after 3 or 12 hours – depending on
the type of control panel.
Functions. AUTOMATIC ON/OFF.
1 = on, 2 = temperature settings, 3 = off, 4 = lighting, 5 = move left, 6 = reduce
Note: CC 100-3B/3S/12B/12S only
temperature/time and move down, 7 = move right, 8 = increase temperature/time and
move up, 9 = settings menu, 10 = information menu, 11 = display. Setting on/off and temperature.
12 = built-in, factory-set processor, can be customised as desired. Press MENU – Use the left and right arrow keys (  ) to move to timer settings. Use
A simplified version of these instructions are found under INFO in CC 100.

the down arrow ( ) to start programming mode.
CC 100 has a built-in power reserve and you can choose between 7 different Use the up and down arrows (
) to set the start to set the start hour, then shift to
languages. 
minutes with the right arrow ( ). Change the minutes using the up and down arrows
After each power failure, the model designation of the control panel is displayed (
).
for five seconds. 
Use the right arrow ( ) to move to the end hour setting and then the up and down
arrows (

) to set the end hour. Shift to minutes with the right arrow ( ) to set the
Lighting. end time, Change the minutes using the up and down arrows
Lights automatically when the facility starts and switches off automatically when the (

). Use the right arrow ( ) to shift to temperature. Change the temperature using
facility shuts down. You can also switch the lighting on or off manually by pressing the up and down arrows (

). Shift to on/off with the right arrow ( ). Change the
LIGHT. on/off mode using the up and down arrows (
).
Password. Now the setting is programmed and a red LED blinks until the sauna or steam bath
Prevents unauthorised changing of the settings. starts at the time set. After this, it glows steadily (a text on the display tells when this
happens). The sauna switches off automatically 3 or 12 hours after the pre-set time –
Main power switch. depending on the type of control panel.
There is a main power switch on the bottom of the relay box, SE heater and the smaller To be changed more than once: You can switch off your sauna or steam bath manually
steam generators. You need only use this switch if the facility is to be switched off for a at any time by pressing OFF. To restart with the same settings, press MENU – Use the
long time. right and left arrows (  ) to go to timer settings. Start programming mode by
The thermometer should be placed at such a height that the temperature corresponds

pressing the down arrow ( ), shift to on/off with the right arrow ( ). Change the on/off
exactly to the numbers displayed on the CC 100. mode using the up and down arrows (
).
Stand-by. STAND-BY programming.
Stand-by is invaluable for saunas or steambaths in hotels, bath houses and so on, where Note: CC 100-3B/3S/12B/12S only
the frequency of use varies. During low-frequency periods, the facility is set on energy- Press MENU – Use the right and left arrows (  ) to go to stand-by setting. Start
saving "stand-by", which can quickly accelerate to the desired bathing temperature programming mode by pressing the down arrow ( ).

when you press ON. The stand-by function saves significant amounts of money each Use the up and down arrows (
) to set the start hour, then shift to minutes with the
year. 
right arrow ( ). Change the minutes using the up and down arrows
The examples below show how easy it is to programme a suitable bath schedule. (
).
Stand-by examples: 
To be changed more than once: Use the right arrow ( ) to move to end hour setting
Three different bath facilities are open between 8 a.m. and 8 p.m. The bathing and then the up and down arrows (
) to set the end hour. Shift to minutes with the
frequencies of the facilities varies like this: 
right arrow ( ). Change the minutes using the up and down arrows (
). Use the
Alt. 1) A small number of bathers come sporadically throughout the day. Programme 
right arrow ( ) to shift to temperature. Change the temperature using the up and down
stand-by between 800 and 800 pm. The bathers (or bath attendant) activate the arrows (

). Shift to on/off with the right arrow ( ). Change the on/off mode using the
programme by pressing the ON button on the CC panel, or by pressing on the separate, up and down arrows (

).
external ON/OFF switch, if there is one. Now the stand-by is programmed and a red LED blinks until the sauna or steam bath
Alt. 2) A small number of bathers come sporadically between 800 and 2 pm. After 2 pm, starts at the time set. After this, it glows steadily (a text on the display shows that the
there is a steady flow of guests until closing. Programme stand-by between 800 and 8 panel is in a stand-by position and when it will switch on).
pm and programme a fixed ”ON” time between 2 pm and 8 pm. The sporadic bathers As soon as you press ON, the temperature increases to the pre-set bathing
activate the programme by pressing the ON button on the CC panel, or by pressing on temperature. After 1 hour, the facility automatically resumes stand-by temperature.
the separate, external ON/OFF switch, if there is one. Each time you press ON, 1 hour’s bathing time begins.
Alt. 3) A large number of bathers between 800 and 1000, 1 pm and 2 pm and 6 pm and 8 Note: if both the timer time and stand-by time are set to be on at the same time, the
pm. The rest of the day, only sporadic bathers come. Programme stand-by between 800 timer function takes over.
and 8 pm, programme fixed ”ON” times for the steady bath times. The sporadic bathers To be changed more than once: You can switch off your sauna or steam bath manually
activate the programme by pressing the ON button on the CC panel, or by pressing on at any time by pressing OFF. To restart with the same settings, press MENU – Use the
the separate, external ON/OFF switch, if there is one. right and left arrows (  ) to go to stand-by. Start programming mode by pressing the


down arrow ( ), shift to on/off with the right arrow ( ). Change the on/off mode using
SETTINGS the up and down arrows (
).
Password
CC 100 all models Note: CC 100-3B/3S/12B/12S only
Note: for all settings, the Tylarium should be switched OFF. Setting the password.
Language. Press MENU – Use the right and left arrows (  ) to go to password setting. Start
Press MENU – Use the left and right arrow keys ( 

programming mode by pressing the down arrow ( ). Enter the code using all the arrow
) to move to choice of language.

keys ( 
).(After power failure, the code is reset to 1995). Press MENU, use the
Start programming mode by pressing the down arrow ( ).
 
left arrow key ( ) to change the code. Set the new code using all the arrow keys ( 
Use the left and right arrow keys ( ) to select the language. Press the up arrow ( ) to
exit and press MENU to change language.


). Press MENU. Activate on/off with the right arrow ( ), press MENU. Now the
password is activated.
Time (clock). To return to unlocked mode, repeat the above procedure but set on/off to off.
Press MENU – Use the left and right arrow keys ( 
) to move to clock settings. Start Note: Do all other settings before setting the password.
programming mode by pressing the down arrow ( ).

6


SETTINGS
Use the up and down arrows ( ) to set the start hour, then shift to minutes with the

right arrow ( ). Change the minutes using the up and down arrows
(
).
Note: CC 100-0B/0S only
To be changed more than once: Switch to end time setting using the right arrow ( ), 
use the up and down arrows (

) to set the end hour, then shift to minutes with the
Note: for all settings, the Tylarium should be switched OFF. To be changed

right arrow ( ). Change the minutes using the up and down arrows (

). Shift to
more than once: However, temperature and humidity settings can be changed

temperature with the right arrow ( ). Change the temperature using the up and down
when the Tylarium is ON.
arrows (

). Shift to on/off with the right arrow ( ). Change the on/off mode using the
MANUAL ON/OFF. up and down arrows (

).
Note: CC 100-0B/0S only Now the stand-by setting (Monday, setting 1) is done; press MENU to return to
programming mode. Programme the stand-by time for each day. When all settings are
Setting the bathing temperature. done, go back to stand-by settings in the MENU ON, and the stand-by settings are
Press TEMP – the previous temperature is displayed. Use the up and down arrows (

) to change the temperature.
activated. A red LED blinks until the sauna or steam bath starts at a set time; after this
it glows steadily (a text on the display shows that the panel is in a stand-by position and
Manual on/off. when it will switch on).
Important! Don’t forget to set the off time. The sauna may be switched on for a As soon as you press ON, the temperature increases to the pre-set bathing
maximum of 12 hours. temperature. After 1 hour, the facility resumes the stand-by temperature. Each time the
Press ON to switch the facility on. Press OFF to switch it off. ON button is pressed, a new 1-hour bathing period starts.
Note: if both the timer time and stand-by time are set to be on at the same time, the
PROGRAMMING THE WEEKLY TIMER timer function takes over.
with different settings for different days of the week. To switch the Tylarium off manually, press OFF. (This only switches off the current
Note: CC 100-0B/0S only bath).
Setting on/off, temperature. To be changed more than once: To de-programme the stand-by settings, press MENU,
Press MENU – Use the left and right arrow keys (  ) to set the timer. Start use the left and right arrows (  ) to shift to the stand-by setting and press OFF.
programming mode using the down arrow ( ).
To restart with the same settings, press MENU, go to stand-by using the left and right
Use the left and right arrow keys (  ) to set the day (for example, Monday). Shift to arrows (  ), and press ON.
programming mode by pressing the down arrow ( ).
NOTE: Always block with a password after Standby programming.
Choose the setting number (such as setting 1) with the left and right arrow keys (  ).
Shift to programming mode by pressing the down arrow ( ).
STAND-BY PROGRAMMING
Use the up and down arrows (
) to set the start hour, then shift to minutes with the with the same setting for all days of the week.

right arrow ( ). Change the minutes using the up and down arrows Note: CC 100-0B/0S only.

(
). Press MENU – Use the left and right arrow keys (


) to set the stand-by timer. Start

To be changed more than once: Use the right arrow ( ) to move to end hour setting
programming mode using the down arrow ( ).

and then the up and down arrows (
) to set the end hour. Shift to minutes with the Use the left and right arrow ( ) keys to select the mode WEEK. Shift to



right arrow ( ). Change the minutes using the up and down arrows (
). Shift to programming mode by pressing the down arrow ( ).

temperature with the right arrow ( ). Change the temperature using the up and down Use the up and down arrows (

) to set the start time, then shift to minutes with the
arrows (

). Shift to on/off with the right arrow ( ). Change the on/off mode using the 
right arrow ( ). Change the minutes using the up and down arrows ( ).

up and down arrows (
). To be changed more than once: Switch to end time setting using the right arrow ( ), 
Now the setting (Monday, setting 1) is done; press MENU to return to programming use the up and down arrows (

) to set the end hour, then shift to minutes with the
mode. Programme the stand-by times for each day by moving to the day/setting with 
right arrow ( ). Change the minutes using the up and down arrows
the left and right arrow keys (  ). You can programme a maximum of four time (

). Shift to temperature with the right arrow ( ). Change the temperature using the
settings per day. When all settings are done, go back to timer settings by pressing up and down arrows (

). Shift to on/off with the right arrow ( ). Change the on/off
MENU twice, press ON, and the weekly settings are activated. To be changed more mode using the up and down arrows (

).
than once: A red LED blinks until the sauna or steam bath starts at a set time; after this Now the stand-by time is programmed in. Go back to stand-by programming by
it glows steadily (a text on the display tells when this happens). pressing MENU twice, press ON. A red LED blinks until the sauna or steam bath starts
To switch the Tylarium off manually, press OFF. (This only switches off the current at a set time; then it glows steadily (a text on the display tells that the panel is on stand-
bath). by and when it will switch on).
To de-programme the weekly settings, press MENU, use the left and right arrows (  As soon as you press ON, the temperature increases to the pre-set bathing temperature.
 ) to shift to timer settings and press OFF. After 1 hour, the facility automatically resumes stand-by temperature. Each time you
press ON, 1 hour’s bathing time begins.
PROGRAMMING THE WEEKLY TIMER Note: if both the timer time and stand-by time are set to be on at the same time, the
with the same setting for all days of the week. timer function takes over.
Note: CC 100-0B/0S only To switch the Tylarium off manually, press OFF. (This only switches off the current
Setting on/off, temperature. bath).
Press MENU – Use the left and right arrow keys (  ) to set the timer. Start To be changed more than once: To de-programme the stand-by settings, press MENU,
programming mode using the down arrow ( ).
use the left and right arrows (  ) to shift to the stand-by setting and press OFF.
Use the left and right arrow (  ) keys to select the mode WEEK. Shift to To restart with the same settings, press MENU, go to stand-by using the left and right
programming mode by pressing the down arrow ( ).
arrows (  ), and press ON.
Select the setting number (for example, setting 1) using the left and right arrow keys (  NOTE: Always block with a password after Standby programming.
 ).


Use the down arrow ( ) to move the programming mode, then use the up and down Password.
arrows (

) to set the start hour. Shift to minutes with the right arrow ( ). Change the Setting the password.
minutes using the up and down arrows (
). Press MENU – Use the right and left arrows ( 
) to go to password setting. Start

Shift to end time setting using the right arrow ( ), then use the up and down arrows (

programming mode by pressing the down arrow ( ). Enter the code using all the arrow


) to change the end time, then shift to minutes with the right arrow ( ). Change the keys ( 
). After power failure, the code is reset to 1995). Press MENU, use the
minutes using the up and down arrows (
). Shift to temperature with the right arrow 
left arrow key ( ) to change the code. Set the new code using all the arrow keys ( 

( ). Change the temperature using the up and down arrows (
). Shift to on/off with

). Press MENU. Activate on/off with the right arrow ( ), press MENU. Now the

the right arrow ( ). Change the on/off mode using the up and down arrows (
). password is activated.
Now the setting (1) is done; press MENU to return to programming mode. Programme To return to unlocked mode, repeat the above procedure but set on/off to off.
each setting using the left and right arrow keys (  ). The Tylarium can be Note: Do all other settings before setting the password.
programmed to switch on and off four times a day. When all settings are done, go back
to timer settings by pressing MENU twice, press ON, and the weekly settings are BATHING OUTSIDE OF THE PROGRAMMED TIME
activated. A red LED blinks until the sauna or steam bath starts at a set time; after this if the panel is locked with a password.
it glows steadily (a text on the display tells when this happens).
The sauna or steam bath can be used at a different time than the programmed time.
To switch the Tylarium off manually, press OFF. (This only switches off the current
Press ON to start a one-hour bathing period. To extend the bath, press ON again. The
bath).
To de-programme the weekly settings, press MENU, use the left and right arrows (  facility automatically switches off one hour after the last time ON was pressed.
 ) to shift to timer settings and press OFF.
TYLÖ AB, Svarvaregatan 6, S-30250 Halmstad, Sweden.
STAND-BY PROGRAMMING Phone 035-299 00 00, Fax 035-299 01 98
with different settings for different days of the week. © This publication may not be reproduced, in part or in whole, without the written permission of Tylö. Tylö
Note: CC 100-0B/0S only. reserves the right to make changes in materials, construction and design.
Press MENU – Use the left and right arrow keys ( 
) to set the stand-by timer. Start
programming mode using the down arrow ( ).

Use the left and right arrow keys ( 
) to set the day (for example, Monday). Shift to
programming mode by pressing the down arrow ( ).