MULTI-V WATER II (R410A,60Hz)_6CVT0-01A_09
MULTI-V WATER II (R410A,60Hz)_6CVT0-01A_09
6CVT0-01A
LG Airconditioners Product Data
(R410A)
• Introduction
• General Information
• Outside Units
• Installation of Outside Units
• Special Guide
Introduction
1. Preface
R410A Model
is the most favored choice when there is a need for precise air conditioning of relatively big pro-
jects extending from Multi-Room structure to big commercial places. We have a big line up, that offers wider
flexibility of model selection.
Equipped with inverter technology and long piping installation, the product matches well if one talk about opti-
mum power consumption in high rise buildings. Add on capacity feature makes it easy to upgrade the existing
capacity at any time.
With the growing concern about environment preservation, comes with R410A refrigerant which is
environment friendly and thus our system is a high technology and environment friendly product.
Unique refrigerant flow and electronic circuit control gives this system an unique capability to work in
extreme/abnormal working conditions making our customer feel great about their decision of selecting
LG as their first choice.
This publication provides a detailed and in depth information about the design and installation of .
We hope that with this information you would become an expert of your system.
Air-Conditioning Company
Introduction
2. Step by Step System Selection Process
(1) Calculate or obtain the maximum heat load for the area(s) to be air conditioned
• Air conditionerss should not be installed in areas where corroslve gases, such as acid or
alkaline gas, are produced.
Introduction
General Information
1. Model Names
2. External Appearance
4. Nomenclature
General information 1
2. External Appearance
2.1 460V
ARWN100DA2
ARWN200DA2
ARWN300DA2
ARWN400DA2
ARWN500DA2
ARWN600DA2
2 General information
2.2 220V
ARWN80BA2
ARWN160BA2
ARWN240BA2
ARWN320BA2
ARWN400BA2
ARWN480BA2
General information 3
3. Nomenclature
ARW N 100 D A 2
Serial Number
A: Basic Function
Electrical Ratings
B: 3Ø, 220V, 60Hz
D: 3Ø, 460V, 60Hz
4 General information
4. Outside Units Information
CAUTION
• Ratio of the running Indoor Units to the Outside: Within 10 ~ 100%
• A combination operation over 100% cause to reduce each indoor unit capacity.
■ Combination Ration(50~200%)
Outside Number Connection Capacity
Single outside units 200%
Double outside units 160%
Triple outside units 130%
Notes:
* We can guarantee the operation only within 130% Combination.
If you want to connect more than 130% combination, please contact us and discuss the require-
ment like below.
1) If the operation of indoor unit is more than 130%, low airflow operation is recommended in all
the indoor units.
2) If the operation of indoor unit is more than 130%, additional refrigerant is needed according to
the headquarter guidance.
3)Over 130%, capacity is same as capacity of 130%, Same remark is valid for power input.
System Capacity HP 40 50 60
Model Name ARWN400DA2 ARWN500DA2 ARWN600DA2
Product Refrigerant Charge kg 8.8 + 8.8 8.8 + 8.8 + 7.3 8.8 + 8.8 + 8.8
CF(Correction Factor) kg - - -
Maximum Connectable No. of Indoor Units 64 64 64
kg 238 + 238 238 + 238 + 170 238 + 238 + 238
Net Weight
lb 524.7 + 524.7 524.7 + 524.7 + 374.8 524.7 + 524.7 + 524.7
mm (772x1,120x547) x 2 (772x1,120x547) x 3 (772x1,120x547) x 3
Dimensions(WxHxD)
inch (30.4x44.1x21.5) x 2 (30.4x44.1x21.5) x 3 (30.4x44.1x21.5) x 3
Refrigerant Liquid mm(inch) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Connecting Pipes Gas mm(inch) 41.3(1 5/8) 41.3(1 5/8) 41.3(1 5/8)
Inlet mm PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Water
Outlet mm PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Connecting Pipes
Drain Outlet mm 20 20 20
General information 5
Power Supply: Outside Unit (3Ø, 220V, 60Hz)
System Capacity HP 8 16 24
Model Name ARWN80BA2 ARWN160BA2 ARWN240BA2
Product Refrigerant Charge kg 7.3 8.8 8.8 + 7.3
CF(Correction Factor) kg - - -
Maximum Connectable No. of Indoor Units 13 26 39
kg 170 238 238 + 170
Net Weight
lb 374.8 524.7 524.7 + 374.8
mm 772x1,120x547 772x1,120x547 (772x1,120x547) x 2
Dimensions(WxHxD)
inch 30.4x44.1x21.5 30.4x44.1x21.5 (30.4x44.1x21.5) x 2
Refrigerant Liquid mm(inch) 9.52(3/8) 12.7(1/2) 19.05(3/4)
Connecting Pipes Gas mm(inch) 22.2(7/8) 28.58(1 1/8) 34.9(1 3/8)
Inlet mm PT32A PT40A PT40A + PT32A
Water
Outlet mm PT32A PT40A PT40A + PT32A
Connecting Pipes
Drain Outlet mm 20 20 20
System Capacity HP 32 40 48
Model Name ARWN320BA2 ARWN400BA2 ARWN480BA2
Product Refrigerant Charge kg 8.8 + 8.8 8.8 + 8.8 + 7.3 8.8 + 8.8 + 8.8
CF(Correction Factor) kg - - -
Maximum Connectable No. of Indoor Units 52 64 64
kg 238 + 238 238 + 238 + 170 238 + 238 + 238
Net Weight
lb 524.7 + 524.7 524.7 + 524.7 + 374.8 524.7 + 524.7 + 524.7
mm (772x1,120x547) x 2 (772x1,120x547) x 3 (772x1,120x547) x 3
Dimensions(WxHxD)
inch (30.4x44.1x21.5) x 2 (30.4x44.1x21.5) x 3 (30.4x44.1x21.5) x 3
Refrigerant Liquid mm(inch) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Connecting Pipes Gas mm(inch) 41.3(1 5/8) 41.3(1 5/8) 41.3(1 5/8)
Inlet mm PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Water
Outlet mm PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Connecting Pipes
Drain Outlet mm 20 20 20
6 General information
Outside Units
1. Specifications
2. Dimensions
3. Piping Diagrams
4. Wiring Diagrams
5. Field Wiring
6. Electric Characteristics
7. Capacity Tables
8. Operation Limits
9. Sound Levels
10. Accessories
Outside Units
1. Specifications
System Capacity HP 10 20 30
Combination Unit ARWN100DA2 ARWN200DA2 ARWN300DA2
Model Name ARWN100DA2 ARWN200DA2 ARWN200DA2
Independent Unit
ARWN100DA2
Power Supply Ø,V,Hz 3,460,60 3,460,60 3,460,60
Capacity Cooling kW 28.0 56.0 84.0
kcal/h 24,100 48,200 72,200
Btu/h 95,900 191,100 286,600
Heating kW 31.5 63.0 94.5
kcal/h 27,100 54,200 81,300
Btu/h 107,500 225,000 322,500
Input Cooling kW 5.60 11.20 16.80
Heating kW 5.80 11.70 17.50
COP Cooling kW 5.00 5.00 5.00
Heating kW 5.43 5.38 5.40
Casing Color Warm Gray Warm Gray Warm Gray
Compressor Type DC Inverter Scroll DC Inverter Scroll DC Inverter Scroll
Combination (Inverter)x1 (Inverter)x1, (Constant)x1 (Inverter)x2, (Constant)x1
Piston Displacement cm3/rev 52 52 + 81.0 (52 x2) + 81.0
Number of Revolution Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz
rev/min
+ Constant 3,469 at 60Hz + Constant 3,469 at 60Hz
Motor Output kW 5.4 5.4 + 6.4 (5.4 x 2)+ 6.4
Starting Method Direct On Line Direct On Line Direct On Line
Oil Type FVC68D(PVE) FVC68D(PVE) FVC68D(PVE)
Oil Charge Amount cc 2,325±10 (2,325±10) + (2,325±70) (2,325±10)*2 + (2,325±70)
Heat Exchanger Type Stainless Steel Plate Stainless Steel Plate Stainless Steel Plate
Maximum Pressure Resistance kgf/cm2 45 45 45
Head Loss kPa 26.5 43 43 + 26.5
Rated Water Flow LPM 96 192 192 + 96
Refrigerant Liquid mm(inch) 9.52(3/8) 12.7(1/2) 19.05(3/4)
Connecting Pipes Low Pressure Gas mm(inch) 22.2(7/8) 28.58(1 1/8) 34.9(1 3/8)
High Pressure Gas mm(inch) - - -
Water Inlet PT32A PT40A PT40A + PT32A
Connecting Pipes Outlet PT32A PT40A PT40A + PT32A
Drain Outlet 20mm 20mm 20mm
Dimension(WxHxD) mm 772x1,120x547 772x1,120x547 (772x1,120x547) x 2
inch 30.4x44.1x21.5 30.4x44.1x21.5 (30.4x44.1x21.5) x 2
Net Weight kg 170 238 238 + 170
lb 374.8 524.7 524.7 + 374.8
Transmission Cable(CVV-SB) mm2 1.0 ~ 1.5 1.0 ~ 1.5 1.0 ~ 1.5
Refrigerant Name R410A R410A R410A
Charge Amount kg 7.3 8.8 8.8 + 7.3
Control Device EEV EEV EEV
Range of Operation Cooling °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Water Temp. Heating °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Simulaneous °C/°F - - -
Maximum Connectable No. of Indoor Units 16 32 49
Notes:
1. Capacities and Inputs are based on the following conditions
Cooling : Indoor temp. 27°C [80.6°F]DB/19°C[66.2°F]WB
Water inlet temp. 30°C[86°F]
Heating : Indoor temp. 20°C[68°F]DB
Water Inlet temp. 20°C[68°F]
* Interconnecting Piping Length 7.5m
* Level Difference of Zero
2. Capacities are net capacities
3. Due to our policy of innovation some specifications may be changed without notification
1 Outside Units
Heat Pump(460V, 60Hz)
System Capacity HP 40 50 60
Combination Unit ARWN400DA2 ARWN500DA2 ARWN600DA2
Model Name ARWN200DA2 ARWN200DA2 ARWN200DA2
Independent Unit ARWN200DA2 ARWN200DA2 ARWN200DA2
ARWN100DA2 ARWN200DA2
Power Supply Ø,V,Hz 3,460,60 3,460,60 3,460,60
Capacity Cooling kW 112.0 140.0 168.0
kcal/h 96,300 120,400 144,400
Btu/h 382,200 477,800 573,400
Heating kW 126.0 157.5 189.0
kcal/h 108,400 135,400 162,400
Btu/h 429,900 537,500 645,000
Input Cooling kW 22.40 28.00 33.60
Heating kW 23.40 29.20 35.00
COP Cooling kW 5.00 5.00 5.00
Heating kW 5.38 5.39 5.40
Casing Color Warm Gray Warm Gray Warm Gray
Compressor Type DC Inverter Scroll DC Inverter Scroll DC Inverter Scroll
Combination (Inverter + Constant)x2 (Inverter) x3 + (Constant)x2 (Inverter + Constant)x3
Piston Displacement cm3/rev (52 + 81.0) x 2 (52 x 3) + (81.0 x 2) (52 + 81.0) x 3
Number of Revolution Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz
rev/min
+ Constant 3,469 at 60Hz + Constant 3,469 at 60Hz + Constant 3,469 at 60Hz
Motor Output kW (5.4 + 6.4) x 2 (5.4 x 3) + (6.4 x 2) (5.4 + 6.4) x 3
Starting Method Direct On Line Direct On Line Direct On Line
Oil Type FVC68D(PVE) FVC68D(PVE) FVC68D(PVE)
Oil Charge Amount cc (2,325±10) x 2 + (2,325±70)x2 (2,325±10) x 3 + (2,325±70)x2 (2,325±10) x 3 + (2,325±70)x3
Heat Exchanger Type Stainless Steel Plate Stainless Steel Plate Stainless Steel Plate
Maximum Pressure Resistance kgf/cm2 45 45 45
Head Loss kPa 43 + 43 43 + 43 + 26.5 43 + 43 + 43
Rated Water Flow LPM 192 + 192 192 + 192 + 96 192 + 192 + 192
Refrigerant Liquid mm(inch) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Connecting Pipes Low Pressure Gas mm(inch) 41.3(1 5/8) 41.3(1 5/8) 41.3(1 5/8)
High Pressure Gas mm(inch) - - -
Water Inlet PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Connecting Pipes Outlet PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Drain Outlet 20mm 20mm 20mm
Dimension(WxHxD) mm (772x1,120x547) x 2 (772x1,120x547) x 3 (772x1,120x547) x 3
inch (30.4x44.1x21.5) x 2 (30.4x44.1x21.5) x 3 (30.4x44.1x21.5) x 3
Net Weight kg 238 + 238 238 + 238 + 170 238 + 238 + 238
lb 524.7 + 524.7 524.7 + 524.7 + 374.8 524.7 + 524.7 + 524.7
Transmission Cable(CVV-SB) mm2 1.0 ~ 1.5 1.0 ~ 1.5 1.0 ~ 1.5
Refrigerant Name R410A R410A R410A
Charge Amount kg 8.8 + 8.8 8.8 + 8.8 + 7.3 8.8 + 8.8 + 8.8
Control Device EEV EEV EEV
Range of Operation Cooling °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Water Temp. Heating °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Simulaneous °C/°F - - -
Maximum Connectable No. of Indoor Units 64 64 64
Notes:
1. Capacities and Inputs are based on the following conditions
Cooling : Indoor temp. 27°C [80.6°F]DB/19°C[66.2°F]WB
Water inlet temp. 30°C[86°F]
Heating : Indoor temp. 20°C[68°F]DB
Water Inlet temp. 20°C[68°F]
* Interconnecting Piping Length 7.5m
* Level Difference of Zero
2. Capacities are net capacities
3. Due to our policy of innovation some specifications may be changed without notification
Outside Units 2
1.2 Heat Pump(220V)
Heat Pump(220V, 60Hz)
System Capacity HP 8 16 24
Combination Unit ARWN80BA2 ARWN160BA2 ARWN240BA2
Model Name ARWN80BA2 ARWN160BA2 ARWN160BA2
Independent Unit
ARWN80BA2
Power Supply Ø,V,Hz 3,220,60 3,220,60 3,220,60
Capacity Cooling kW 22.4 44.8 67.2
kcal/h 19,300 38,500 57,800
Btu/h 76,400 152,900 229,300
Heating kW 25.2 50.4 75.6
kcal/h 21,700 43,300 65,000
Btu/h 86,000 172,000 258,000
Input Cooling kW 4.67 9.34 14.01
Heating kW 4.85 9.70 14.55
COP Cooling kW 4.80 4.80 4.80
Heating kW 5.20 5.20 5.20
Casing Color Warm Gray Warm Gray Warm Gray
Compressor Type DC Inverter Scroll DC Inverter Scroll DC Inverter Scroll
Combination (Inverter)x1 (Inverter)x1, (Constant)x1 (Inverter)x2, (Constant)x1
Piston Displacement cm3/rev 38.3 38.3 + 59.8 (38.3 x2) + 59.8
Number of Revolution Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz
rev/min
+ Constant 3,500 at 60Hz + Constant 3,500 at 60Hz
Motor Output kW 4.13 4.13 + 5.28 (4.13 x 2)+ 5.28
Starting Method Direct On Line Direct On Line Direct On Line
Oil Type FVC68D(PVE) FVC68D(PVE) FVC68D(PVE)
Oil Charge Amount cc 2,325±10 (2,325±10) + (2,325±70) (2,325±10)*2 + (2,325±70)
Heat Exchanger Type Stainless Steel Plate Stainless Steel Plate Stainless Steel Plate
Maximum Pressure Resistance kgf/cm2 45 45 45
Head Loss kPa 26.5 43 43 + 26.5
Rated Water Flow LPM 80 160 160 + 80
Refrigerant Liquid mm(inch) 9.52(3/8) 12.7(1/2) 19.05(3/4)
Connecting Pipes Low Pressure Gas mm(inch) 22.2(7/8) 28.58(1 1/8) 34.9(1 3/8)
High Pressure Gas mm(inch) - - -
Water Inlet PT32A PT40A PT40A + PT32A
Connecting Pipes Outlet PT32A PT40A PT40A + PT32A
Drain Outlet 20mm 20mm 20mm
Dimension(WxHxD) mm 772x1,120x547 772x1,120x547 (772x1,120x547) x 2
inch 30.4x44.1x21.5 30.4x44.1x21.5 (30.4x44.1x21.5) x 2
Net Weight kg 170 238 238 + 170
lb 374.8 524.7 524.7 + 374.8
Transmission Cable(CVV-SB) mm2 1.0 ~ 1.5 1.0 ~ 1.5 1.0 ~ 1.5
Refrigerant Name R410A R410A R410A
Charge Amount kg 7.3 8.8 8.8 + 7.3
Control Device EEV EEV EEV
Range of Operation Cooling °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Water Temp. Heating °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Simulaneous °C/°F - - -
Maximum Connectable No. of Indoor Units 13 26 39
Notes:
1. Capacities and Inputs are based on the following conditions
Cooling : Indoor temp. 27°C [80.6°F]DB/19°C[66.2°F]WB
Water inlet temp. 30°C[86°F]
Heating : Indoor temp. 20°C[68°F]DB
Water Inlet temp. 20°C[68°F]
* Interconnecting Piping Length 7.5m
* Level Difference of Zero
2. Capacities are net capacities
3. Due to our policy of innovation some specifications may be changed without notification
3 Outside Units
Heat Pump(220V, 60Hz)
System Capacity HP 32 40 48
Combination Unit ARWN320BA2 ARWN400BA2 ARWN480BA2
Model Name ARWN160BA2 ARWN160BA2 ARWN160BA2
Independent Unit ARWN160BA2 ARWN160BA2 ARWN160BA2
ARWN80BA2 ARWN160BA2
Power Supply Ø,V,Hz 3,220,60 3,220,60 3,220,60
Capacity Cooling kW 89.6 112.0 134.4
kcal/h 77,100 96,300 115,500
Btu/h 305,700 382,200 458,700
Heating kW 100.8 126.0 151.2
kcal/h 86,700 108,400 129,900
Btu/h 343,900 429,900 516,000
Input Cooling kW 18.68 23.35 28.02
Heating kW 19.40 24.25 29.10
COP Cooling kW 4.80 4.80 4.80
Heating kW 5.20 5.20 5.20
Casing Color Warm Gray Warm Gray Warm Gray
Compressor Type DC Inverter Scroll DC Inverter Scroll DC Inverter Scroll
Combination (Inverter + Constant)x2 (Inverter) x3 + (Constant)x2 (Inverter + Constant)x3
Piston Displacement cm3/rev (38.3 + 59.8) x2 (38.3x3) + (59.8 x2) (38.3 + 59.8) x 3
Number of Revolution Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz Inverter 3,600 at 60Hz
rev/min
+ Constant 3,500 at 60Hz + Constant 3,500 at 60Hz + Constant 3,500 at 60Hz
Motor Output kW (4.13 + 5.28) x 2 (4.13x3) + (5.28x 2) (4.13 + 5.28) x 3
Starting Method Direct On Line Direct On Line Direct On Line
Oil Type FVC68D(PVE) FVC68D(PVE) FVC68D(PVE)
Oil Charge Amount cc (2,325±10) x 2 + (2,325±70)x2 (2,325±10) x 3 + (2,325±70)x2 (2,325±10) x 3 + (2,325±70)x3
Heat Exchanger Type Stainless Steel Plate Stainless Steel Plate Stainless Steel Plate
Maximum Pressure Resistance kgf/cm2 45 45 45
Head Loss kPa 43 + 43 43 + 43 + 26.5 43 + 43 + 43
Rated Water Flow LPM 160 + 160 160 + 160 + 80 160 + 160 + 160
Refrigerant Liquid mm(inch) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Connecting Pipes Low Pressure Gas mm(inch) 41.3(1 5/8) 41.3(1 5/8) 41.3(1 5/8)
High Pressure Gas mm(inch) - - -
Water Inlet PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Connecting Pipes Outlet PT40A + PT40A PT40A + PT40A + PT32A PT40A + PT40A + PT40A
Drain Outlet 20mm 20mm 20mm
Dimension(WxHxD) mm (772x1,120x547) x 2 (772x1,120x547) x 3 (772x1,120x547) x 3
inch (30.4x44.1x21.5) x 2 (30.4x44.1x21.5) x 3 (30.4x44.1x21.5) x 3
Net Weight kg 238 + 238 238 + 238 + 170 238 + 238 + 238
lb 524.7 + 524.7 524.7 + 524.7 + 374.8 524.7 + 524.7 + 524.7
Transmission Cable(CVV-SB) mm2 1.0 ~ 1.5 1.0 ~ 1.5 1.0 ~ 1.5
Refrigerant Name R410A R410A R410A
Charge Amount kg 8.8 + 8.8 8.8 + 8.8 + 7.3 8.8 + 8.8 + 8.8
Control Device EEV EEV EEV
Range of Operation Cooling °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Water Temp. Heating °C/°F 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113 10 ~ 45/ 50 ~ 113
Simulaneous °C/°F - - -
Maximum Connectable No. of Indoor Units 52 64 64
Notes:
1. Capacities and Inputs are based on the following conditions
Cooling : Indoor temp. 27°C [80.6°F]DB/19°C[66.2°F]WB
Water inlet temp. 30°C[86°F]
Heating : Indoor temp. 20°C[68°F]DB
Water Inlet temp. 20°C[68°F]
* Interconnecting Piping Length 7.5m
* Level Difference of Zero
2. Capacities are net capacities
3. Due to our policy of innovation some specifications may be changed without notification
Outside Units 4
5
Outside Unit
ARWN100DA2
58
50 658 50
ARWN200DA2
ARWN80BA2
15
15
ARWN160BA2
L7
569
W mm(inch) 772(30-13/32)
H mm(inch) 1,120(44-3/32)
D mm(inch) 547(21-17/32)
L1 mm(inch) 1,027(40-7/16)
2. Dimensions
L2 mm(inch) 1,057(41-5/8)
L3 mm(inch) 597(23-1/2)
L4 mm(inch) 445(17-17/32)
Water Outlet
L5 mm(inch) 325(12-13/16)
L6 mm(inch) 235(9-1/4)
L7 mm(inch) 599(23-19/32)
Water Inlet
L1
H
77
L2
Liquid Pipe
63
Gas Pipe
92
L3
High/Low Pressure Common
L4
70
L5
L6
32
386
W D
Outside Units
Outside Unit
ARWN300DA2
Outside Units
58 ARWN400DA2
50 658 50 ARWN240BA2
15
15
ARWN320BA2
L7
W mm(inch) 772(30-13/32)
569
H mm(inch) 1,120(44-3/32)
D mm(inch) 547(21-17/32)
L1 mm(inch) 1,027(40-7/16)
L2 mm(inch) 1,057(41-5/8)
L3 mm(inch) 597(23-1/2)
L4 mm(inch) 445(17-17/32)
L5 mm(inch) 325(12-13/16)
Water Outlet
L6 mm(inch) 235(9-1/4)
L7 mm(inch) 599(23-19/32)
L8 mm(inch) 100(5-7/8)
Water Inlet
L1
H
77
L2
63 Liquid Pipe
Gas Pipe
92
L3
High/Low Pressure Common
L4
70
L5
L6
32
386
W L8 D
6
7
Outside Unit
ARWN500DA2
ARWN600DA2
58
50 658 50 ARWN400BA2
15
15
ARWN480BA2
L7
569
W mm(inch) 772(30-13/32)
Water Outlet
H mm(inch) 1,120(44-3/32)
D mm(inch) 547(21-17/32)
L1 mm(inch) 1,027(40-7/16)
Water Inlet
L2 mm(inch) 1,057(41-5/8)
L1
77
H
L2
L3 mm(inch) 597(23-1/2)
63 Liquid Pipe
L4 mm(inch) 445(17-17/32)
Gas Pipe
L3
92
High/Low Pressure Common
L5 mm(inch) 325(12-13/16)
L4
70
L5
L6 mm(inch) 235(9-1/4)
L6
L7 mm(inch) 599(23-19/32)
32
386 L8 mm(inch) 100(5-7/8)
W L8 W L8 W D
Outside Units
3. Piping Diagrams
ARWN100DA2, ARWN80BA2
Water Water
Inlet Outlet
Pipe Pipe
s
HIgh
Outdoor
Air Hot Gas Bypass
Accum
Plate
Heat O/S
Low
Exchanger
Oil return
INV
Comp
s
Receiver Liquid
Injection
SC HEX
Outside Units 8
ARWN200DA2, ARWN160BA2
Water Water
Inlet Outlet
Pipe Pipe
s
HIgh
Outdoor
Air Hot Gas Bypass
Accum
Plate
Heat O/S
Exchanger
Low O/S
Oil return
INV Normal
Comp Comp
s
s
Receiver Liquid
Injection
SC HEX
9 Outside Units
Outside Units
• ARWN100DA2
■ 3Ø, 460V
Reactor
BK(R) RD(T) EEV EEV
CN_T2_1
RD RD T R CN_R2_1 T
BK CN_L1(R) RD CN_L3(T)
MAIN
N CN26 CN43 CN44 CN40 CN39 CN38 CN29
CN01
P_CT2_S/W P_CT1_S/W P_INV_S/W
BL CN_N1 BK EEV_SC EEV_INJ EEV_OUT1
CN05 SW02V
LGMV(MAIN) AUTO ADDRESS
CN24
SOL_V_DDC RESET
CN41
CEN_CONTROL
SW01S SW01V
CN22 DATA CONFIRM
RD E_OIL_I
CN04
T SV
CN18
CN36
WH ACCUM(1)
FLASH_WRITE(MAIN)
RD WH BK TH_DISCHARGE(C2)
S
CN17 TH_SC_OUT
BK INVERTER BOARD LIQ_INJ_C1 MAIN BOARD
SV TH_SC_IN
R CN16
CN33
N T S R LIQ_INJ_I
RD BL FAN TH_SC_L
CN15
+ - FAN
NOISE FILTER BOARD TH_DISCHARGE(I)
CN14 TH_HEX 1
U V W MAGNET_C1
SV
CN34
T N T S R
CN11
HEATER_C1 TH_DISCHARGE(C1)
AC220V
BK
CN08
R CN01_1
CN01
U V W
U W BK WH RD
INV. COMP R S T 1(L) 2(N) 3(L) 4(N) 5(A) 5(B)
NOTE(MAIN) NOTE(INV. PCB) BK GR/YL
SYMBOL DESCRIPTION CN32 LOW PRESSURE SENSOR CN01
TO INDOOR
CN04 ONBOARDING TERMINAL CN33(SC_OUT) SUBCOOLING CIRCUIT OUTLET TEMPERATURE SENSOR CN02 MAIN PCB COMMUNICATION TERMINAL
CN33(SC_IN) SUBCOOLING CIRCUIT INTLET TEMPERATURE SENSOR CN04 ONBOARDING TERMINAL WATER FLOW
CN05 JIG CONNECTION TERMINAL
CN06 AC POWER 220V 3Ø 460V SV F/S
CN08 AC POWER 220V CN33(SC_L) SUBCOOLING LIQUID PIPE SENSOR PIPE SWITCH
CN12 DC LINK 700V
CN09 4WAY REVERSING VALVE CN34(DIACHARGE(I)) INVERTER COMP DISCHARGE TEMPERATURE SENSOR 60Hz
CN13 DC 15V
CN10 INVERTER COMP HEATER CN34(HEX1) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR 220V
CN14 U.V.W POWER TERMINAL
CN11 CONSTANT COMP HEATER CN34(HEX2) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR CN_L1(R) R INPUT
CN12 CHECK SOLENOID VALVE CN35(AIR) OUTDOOR TEMPERATURE SENSOR CN_L2(S) S INPUT
CN13 HOT GAS SOLENOID VALVE CN35(SUCTION) SUCTION TEMPERATURE SENSOR CN_L3(T) T INPUT
DDC
CN14 MAGNETIC SWITCH CN35(DISCHARGE(C)) CONSTANT COMP DISCHARGE TEMPERATURE SENSOR
CN15 AC POWER (FAN) CN36 (TH_DISCHARGE(C2)) INLET WATER TEMPERATURE SENSOR
CN16 INVERTER COMP LIQUID INJECTION VALVE CN38 ELECTRIC EXPANSION VALVE (MAIN)
NON-VOLTAGE
CN17 CONSTANT COMP LIQUID INJECTION VALVE CN39 ELECTRIC EXPANSION VALVE (MAIN) COLOR SIGNAL
CN18 ACCUMULATOR SOLENOID VALVE CN40 ELECTRIC EXPANSION VALVE (SUBCOOLER) FIELD WIRING
SYMBOL RD BL WH BK BR YL GN/YL
CN22 WATER PIPE SOLENOID VALVE CN41 CENTRAL CONTROL TERMINAL
COLOR RED BLUE WHITE BLACK BROWN YELLOW GREEN/YELLOW
CN24 DDC(NON-CONNECTING SIGNAL) CN43 HIGH PRESSURE SWITCH(C1) FACTORY WIRING
CN27 CONSTANT CT SENSOR CN44 HIGH PRESSURE SWITCH(INV)
CN29 INVERTER PCB COMMUNICATION SW01S RESET BUTTON
CN30 HIGH PRESSURE SENSOR SW02V AUTO ADDRESSING SWITCH
10
11
• ARWN200DA2
Reactor
BK(R) RD(T) EEV EEV EEV
CN_T2_1
RD RD T R CN_R2_1 T
BK CN_L1(R) RD CN_L3(T)
MAIN
N CN26 CN43 CN44 CN40 CN39 CN38 CN29
CN01
P_CT2_S/W P_CT1_S/W P_INV_S/W
BL CN_N1 BK EEV_SC EEV_INJ EEV_OUT1
CN05 SW02V
LGMV(MAIN) AUTO ADDRESS
CN24
SOL_V_DDC RESET
CN41
CEN_CONTROL
SW01S SW01V
CN22 DATA CONFIRM
RD E_OIL_I
CN04
T SV
CN18
CN36
WH ACCUM(1)
FLASH_WRITE(MAIN)
RD WH BK TH_DISCHARGE(C2)
S SV
CN17 TH_SC_OUT
BK INVERTER BOARD LIQ_INJ_C1 MAIN BOARD
SV TH_SC_IN
R CN16
CN33
N T S R LIQ_INJ_I
RD BL FAN TH_SC_L
CN15
+ - FAN
NOISE FILTER BOARD TH_DISCHARGE(I)
CN14 TH_HEX 1
U V W MAGNET_C1
SV
CN34
T N T S R
CN11
HEATER_C1 TH_DISCHARGE(C1)
AC220V
BK
CN08
R CN01_1
CN01
U V W
U W RD BK
BK WH RD
INV. COMP R S T 1(L) 2(N) 3(L) 4(N) 5(A) 5(B)
CN05 JIG CONNECTION TERMINAL CN33(SC_IN) SUBCOOLING CIRCUIT INTLET TEMPERATURE SENSOR CN04 ONBOARDING TERMINAL
WATER FLOW M/S
AC POWER 220V CN33(SC_L) SUBCOOLING LIQUID PIPE SENSOR
CN06 AC POWER 220V 3Ø 460V SV F/S
CN08 PIPE SWITCH
CN12 DC LINK 700V 1
CN09 4WAY REVERSING VALVE CN34(DIACHARGE(I)) INVERTER COMP DISCHARGE TEMPERATURE SENSOR 60Hz
CN13 DC 15V
CN10 INVERTER COMP HEATER CN34(HEX1) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR
CN14 U.V.W POWER TERMINAL
220V
CN11 CONSTANT COMP HEATER CN34(HEX2) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR CN_L1(R) R INPUT BK WHRD
CN12 CHECK SOLENOID VALVE CN35(AIR) OUTDOOR TEMPERATURE SENSOR CN_L2(S) S INPUT DDC
CN13 HOT GAS SOLENOID VALVE CN35(SUCTION) SUCTION TEMPERATURE SENSOR CN_L3(T) T INPUT
CN14 MAGNETIC SWITCH CN35(DISCHARGE(C)) CONSTANT COMP DISCHARGE TEMPERATURE SENSOR
U V W
CN15 AC POWER (FAN) CN36 (TH_DISCHARGE(C2)) INLET WATER TEMPERATURE SENSOR NON-VOLTAGE
CN16 INVERTER COMP LIQUID INJECTION VALVE CN38 ELECTRIC EXPANSION VALVE (MAIN)
CN17 CONSTANT COMP LIQUID INJECTION VALVE CN39 ELECTRIC EXPANSION VALVE (MAIN) SIGNAL V
COLOR
CN18 ACCUMULATOR SOLENOID VALVE CN40 ELECTRIC EXPANSION VALVE (SUBCOOLER) FIELD WIRING
SYMBOL RD BL WH BK BR YL GN/YL
CN22 WATER PIPE SOLENOID VALVE CN41 CENTRAL CONTROL TERMINAL
COLOR RED BLUE WHITE BLACK BROWN YELLOW GREEN/YELLOW FACTORY WIRING U W
CN24 DDC(NON-CONNECTING SIGNAL) CN43 HIGH PRESSURE SWITCH(C1)
CN27 CONSTANT CT SENSOR CN44 HIGH PRESSURE SWITCH(INV) COMP 1
CN29 INVERTER PCB COMMUNICATION SW01S RESET BUTTON
CN30 HIGH PRESSURE SENSOR SW02V AUTO ADDRESSING SWITCH
Outside Units
Outside Units
• ARWN80BA2
■ 3Ø, 220V
BK YL RD
S EEV EEV
CN_L2(S)
R T
RY-PWR CN_L3(T)
CN_L1(R)
RD SW01B SW02B 7_SEGMENT
MAIN
CN26 CN43 CN44 CN29
CN02
P_INV_S/W
CN40 CN39 CN38
P_CT2_S/W P_CT1_S/W EEV_OUT1
BK RD YL BK EEV_SC EEV_INJ
CN05 SW02V
LGMV(MAIN) AUTO ADDRESS
CN24
SOL_V_DDC RESET
CN41
CEN_CONTROL
NT SR T S R SW01S SW01V
CN22 DATA CONFIRM
E_OIL_I
CN04
SV
CN18
CN36
TH_DISCHARGE(C2)
RESISTOR PCB
CN17 TH_SC_OUT
PFC & INVERTER BOARD LIQ_INJ_C1 MAIN BOARD
R SV TH_SC_IN
CN16
CN33
S LIQ_INJ_I
T FAN TH_SC_L
N CN15
FAN
RD YL BK TH_DISCHARGE(I)
CN14 TH_HEX 1
U V W MAGNET_C1
SV
CN34
T T S R R T S R
CN11
HEATER_C1 TH_DISCHARGE(C1)
AC220V
BK
CN08
R CN01_1
CN01
U V W
U W BK YL RD
INV. COMP R S T 1(L) 2(N) 3(L) 4(N) 5(A) 5(B)
CN05 JIG CONNECTION TERMINAL CN33(SC_IN) SUBCOOLING CIRCUIT INTLET TEMPERATURE SENSOR CN04 ONBOARDING TERMINAL WATER FLOW
CN06 AC POWER 220V 3Ø 220V3N~ SV F/S
CN08 AC POWER 220V CN33(SC_L) SUBCOOLING LIQUID PIPE SENSOR PIPE SWITCH
CN12 DC LINK 700V
CN09 4WAY REVERSING VALVE CN34(DIACHARGE(I)) INVERTER COMP DISCHARGE TEMPERATURE SENSOR 60Hz
CN13 DC 15V 220V
CN10 INVERTER COMP HEATER CN34(HEX1) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR
CN14 U.V.W POWER TERMINAL
CN11 CONSTANT COMP HEATER CN34(HEX2) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR CN_L1(R) R INPUT
CN12 CHECK SOLENOID VALVE CN35(AIR) OUTDOOR TEMPERATURE SENSOR CN_L2(S) S INPUT DDC
CN13 HOT GAS SOLENOID VALVE CN35(SUCTION) SUCTION TEMPERATURE SENSOR CN_L3(T) T INPUT
CN14 MAGNETIC SWITCH CN35(DISCHARGE(C)) CONSTANT COMP DISCHARGE TEMPERATURE SENSOR
CN15 AC POWER (FAN) CN36 (TH_DISCHARGE(C2)) INLET WATER TEMPERATURE SENSOR NON-VOLTAGE
CN16 INVERTER COMP LIQUID INJECTION VALVE CN38 ELECTRIC EXPANSION VALVE (MAIN)
CN17 CONSTANT COMP LIQUID INJECTION VALVE CN39 ELECTRIC EXPANSION VALVE (MAIN) COLOR
SIGNAL
CN18 ACCUMULATOR SOLENOID VALVE CN40 ELECTRIC EXPANSION VALVE (SUBCOOLER)
SYMBOL RD BL WH BK BR YL GN/YL
FIELD WIRING
CN22 WATER PIPE SOLENOID VALVE CN41 CENTRAL CONTROL TERMINAL
COLOR RED BLUE WHITE BLACK BROWN YELLOW GREEN/YELLOW FACTORY WIRING
CN24 DDC(NON-CONNECTING SIGNAL) CN43 HIGH PRESSURE SWITCH(C1)
CN27 CONSTANT CT SENSOR CN44 HIGH PRESSURE SWITCH(INV)
CN29 INVERTER PCB COMMUNICATION SW01S RESET BUTTON
CN30 HIGH PRESSURE SENSOR SW02V AUTO ADDRESSING SWITCH
12
13
• ARWN160BA2
BK YL RD
R T
R Y-PWR CN_L3(T)
CN_L1(R)
RD SW01B SW02B 7_SEGMEN T
MAIN
CN26 CN43 CN44 CN29
CN02
P_INV_S/W
CN40 CN39 CN38
P_CT2_S/W P_CT1_S/W EEV_OUT1
BK RD YL BK EEV_SC EEV_INJ
L
CN05 SW02V
LGMV(MAIN) AU T O ADDRESS
CN24
SOL_V_DDC RESE T
CN41
CEN_CONTRO
NT SR T S R SW01S SW01V
CN22 D AT A CONFIRM
E_OIL_I
CN04
SV
CN18
CN36
TH_DISCHARGE(C2)
RESIS T OR PCB
SV
CN17 TH_SC_OU T
PFC & INVE R TER BOARD LIQ_INJ_C1 MAIN BOARD
R SV TH_SC_IN
CN16
CN33
S LIQ_INJ_I
T FAN TH_SC_ L
N CN15
FAN
RD YL BK TH_DISCHARGE(I)
CN14 TH_HEX 1
U V W MAGNET_C1
SV
CN34
T T S R R T S R
CN 11
HE ATER_C1 TH_DISCHARGE(C1)
AC220V
BK
CN08
R CN01_1
CN01
U V W
U W RD BK
BK Y L RD
IN V. COM P R S T 1(L) 2(N) 3(L) 4(N) 5(A) 5(B)
CN05 JIG CONNECTION TERMINAL CN33(SC_IN) SUBCOOLING CIRCUIT INTLET TEMPERATURE SENSOR CN04 ONBOARDING TERMINAL W ATER FLOW M/S
CN06 AC POWER 220V 3Ø 220V3N~ SV F/S
CN08 AC POWER 220V CN33(SC_L) SUBCOOLING LIQUID PIPE SENSOR PIPE SWITCH
CN12 DC LINK 700V 1
CN09 4WAY REVERSING VALVE CN34(DIACHARGE(I)) INVERTER COMP DISCHARGE TEMPERATURE SENSOR 60Hz
CN13 DC 15V 220V
CN10 INVERTER COMP HEATER CN34(HEX1) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR
CN14 U.V.W POWER TERMINAL
CN11 CONSTANT COMP HEATER CN34(HEX2) OUTDOOR HEAT EXCHANGER TEMPERATURE SENSOR CN_L1(R) R INPUT
BK Y L RD
CN12 CHECK SOLENOID VALVE CN35(AIR) OUTDOOR TEMPERATURE SENSOR CN_L2(S) S INPUT DDC
CN13 HOT GAS SOLENOID VALVE CN35(SUCTION) SUCTION TEMPERATURE SENSOR CN_L3(T) T INPUT
CN14 MAGNETIC SWITCH CN35(DISCHARGE(C)) CONSTANT COMP DISCHARGE TEMPERATURE SENSOR U V W
CN15 AC POWER (FAN) CN36 (TH_DISCHARGE(C2)) INLET WATER TEMPERATURE SENSOR NON-VOLTAGE
CN16 INVERTER COMP LIQUID INJECTION VALVE CN38 ELECTRIC EXPANSION VALVE (MAIN)
CN17 CONSTANT COMP LIQUID INJECTION VALVE CN39 ELECTRIC EXPANSION VALVE (MAIN)
SIGNAL V
COLOR FIELD WIRING
CN18 ACCUMULATOR SOLENOID VALVE CN40 ELECTRIC EXPANSION VALVE (SUBCOOLER)
SYMBOL RD BL WH BK BR YL GN/YL
CN22 WATER PIPE SOLENOID VALVE CN41 CENTRAL CONTROL TERMINAL
COLOR RED BLUE WHITE BLACK BROWN YELLOW GREEN/YELLOW FAC T O RY WIRING U W
CN24 DDC(NON-CONNECTING SIGNAL) CN43 HIGH PRESSURE SWITCH(C1)
CN27 CONSTANT CT SENSOR CN44 HIGH PRESSURE SWITCH(INV) COM P 1
CN29 INVERTER PCB COMMUNICATION SW01S RESET BUTTON
CN30 HIGH PRESSURE SENSOR SW02V AUTO ADDRESSING SWITCH
Outside Units
5. Field Wiring
Power supply
1 Phase 60Hz
220V
WARNING
• Indoor unit ground lines are required for preventing electrical shock accident in current leakage,
transmission disorder by noise effect and motor current leakage (without connection to pipe).
• Don't install an individual switch or electrical outlet to disconnect each of indoor unit separately from the
power supply.
3 4 3 4 3 4
The GND terminal is a '–' terminal for the central controller, not ground line
Outside Units 14
■ 1 Outside Unit - 3Ø, 220V
Power supply
1 Phase 60Hz
220V
WARNING
• Indoor unit ground lines are required for preventing electrical shock accident in current leakage,
transmission disorder by noise effect and motor current leakage (without connection to pipe).
• Don't install an individual switch or electrical outlet to disconnect each of indoor unit separately from the
power supply.
3 4 3 4 3 4
The GND terminal is a '–' terminal for the central controller, not ground line
15 Outside Units
6. Electric Characteristics
◆ Wiring of Main Power Supply and Equipment Capacity
1. Use a separate power supply for the Outside Unit and Indoor Unit.
2. The wire size is the minimum value for metal conduit wiring. The power cord size should be 1 rank thicker taking into account the
line voltage drops. Make sure the power-supply voltage does not drop more than 10%.
3. Specific wiring requirements should adhere to the wiring regulations of the region.
4. Power supply cords of parts of appliances for outside use should not be lighter than polychloroprene sheathed flexible cord.
5. Don't install an individual switch or electrical outlet to disconnect each of indoor unit separately from the power supply.
WARNING
• Follow ordinance of your governmental organization for technical standard related to electrical equipment, wiring regu-
lations and guidance of each electric power company.
• Make sure to use specified wires for connections so that no external force is imparted to terminal connections. If con-
nections are not fixed firmly, it may cause heating or fire.
• Make sure to use the appropriate type of overcurrent protection switch. Note that generated overcurrent may include
some amount of direct current.
CAUTION
• Some installation site may require attachment of an earth leakage breaker. If no earth leakage breaker is installed, it may cause
an electric shock.
• Do not use anything other than breaker and fuse with correct capacity. Using fuse and wire or copper wire with too large
capacity may cause a malfunction of unit or fire.
■ 60Hz 460V
Power Supply COMP
Model Hz Volts Voltage-range
MCA TOCA MFA MSC RLA
ARWN100DA2 60 460V 16.8 20.0 20 - 13.4
ARWN200DA2 60 460V 27.4 38.0 35 92.8 13.1+11.0
ARWN300DA2 60 460V Min:414, 40.8 58.0 55 98.6 13.1+11.0+13.4
ARWN400DA2 60 460V Max:506 51.5 76.0 55 109.6 13.1+11.0+13.1+11.0
ARWN500DA2 60 460V 64.9 96.0 70 115.4 13.1+11.0+13.1+11.0+13.4
ARWN600DA2 60 460V 75.6 114.0 90 126.4 13.1+11.0+13.1+11.0+131.+11.0
■ 60Hz 220V
Power Supply COMP
Model Hz Volts Voltage-range
MCA TOCA MFA MSC RLA
ARWN80BA2 60 220V 15.0 20.0 20 - 12.0
ARWN160BA2 60 220V 35.4 45.8 55 103.9 12.0+18.7
ARWN240BA2 60 220V Min:198, 47.4 65.8 55 109.8 12.0+18.7+12.0
ARWN320BA2 60 220V Max:242 66.1 91.6 70 128.5 12.0+18.7+12.0
ARWN400BA2 60 220V 78.1 111.6 90 134.4 12.0+18.7+12.0+18.7
ARWN480BA2 60 220V 96.8 137.4 100 153.1 12.0+18.7+12.0+18.7+12.0+18.7
Outside Units 16
Notes:
1. Voltage range
Voltage supplied to the unit terminals should be within the minimum and maximum range
2. Maximum allowable voltage unbalance between phase is 2 %
3. Select wire spec. based on the larger value of MCA or TOCA. MCA : Minimum Circuit Amperes (A)
4. TOCA means the total over current value of each outside unit. MSC : Maximum Starting Current
5. MSC means the Max. current during the starting of compressor. RLA : Rated Load Amperes (A)
FLA : Full Load Amperes (A)
6. Recommended circuit breaker is ELCB
MFA: Maximum Fuse Amperes(A)
(Earth Leakage Circuit Breaker)
TOCA: Total Over Current Amperes(A)
7. MFA is used to select the circuit breaker and ground fault circuit interrupter
(earth leakage circuit breaker)
17 Outside Units
7. Capacity Tables
7.1 Heat Pump(460V)
7.1.1 Cooling Capacity
ARWN100DA2 Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 18
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
19 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 20
ARWN200DA2
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
21 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 22
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
23 Outside Units
ARWN300DA2
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 24
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
25 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 26
ARWN400DA2
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
27 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 28
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
29 Outside Units
ARWN500DA2
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 30
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
31 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 32
ARWN600DA2
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
33 Outside Units
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 34
Cooling Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
35 Outside Units
7.1.2 Heat Capacity
Heating Capacity(460V)
ARWN100DA2
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 36
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
37 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 38
ARWN200DA2 Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
39 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 40
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
41 Outside Units
ARWN300DA2 Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 42
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
43 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 44
ARWN400DA2 Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
45 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 46
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
47 Outside Units
ARWN500DA2 Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 48
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
49 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 50
ARWN600DA2 Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
51 Outside Units
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 52
Heating Capacity(460V)
TC:Total Capacity(kW)
PI :Power Input(kW)
53 Outside Units
7.2 Heat Pump(220V)
7.2.1 Cooling Capacity Cooling Capacity(220V)
ARWN80BA2
Indoor Air Temperature(°CWB)
Inlet Water
Combination Water Flow 14 16 18 19 20 22 24
(%) Temperature Rate
TC PI TC PI TC PI TC PI TC PI TC PI TC PI
(°C) (L/min)
(kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW)
40 20.5 2.03 22.2 2.37 24.2 2.76 26.3 3.11 27.0 3.18 28.1 3.26 28.9 3.32
15 80 20.5 1.87 22.2 2.21 24.2 2.58 26.3 2.90 27.0 2.98 28.1 3.05 28.9 3.12
100 20.5 1.82 22.2 2.17 24.2 2.53 26.3 2.85 27.0 2.92 28.1 2.99 28.9 3.05
40 20.2 2.46 21.9 2.87 23.8 3.34 25.9 3.76 26.7 3.85 27.7 3.95 28.5 4.02
20 80 20.2 2.26 21.9 2.68 23.8 3.12 25.9 3.52 26.7 3.61 27.7 3.70 28.5 3.78
100 20.2 2.20 21.9 2.63 23.8 3.06 25.9 3.45 26.7 3.54 27.7 3.63 28.5 3.69
40 20.2 3.03 21.9 3.54 23.8 4.12 25.9 4.64 26.7 4.75 27.7 4.87 28.5 4.96
25 80 20.2 2.79 21.9 3.31 23.8 3.85 25.9 4.34 26.7 4.45 27.7 4.57 28.5 4.66
100 20.2 2.71 21.9 3.24 23.8 3.77 25.9 4.25 26.7 4.36 27.7 4.48 28.5 4.55
40 20.2 3.64 21.9 4.25 23.8 4.95 25.9 5.57 26.7 5.70 27.7 5.84 28.5 5.95
130 30 80 20.2 3.35 21.9 3.97 23.8 4.62 25.9 5.21 26.7 5.34 27.7 5.48 28.5 5.59
100 20.2 3.26 21.9 3.89 23.8 4.53 25.9 5.11 26.7 5.24 27.7 5.37 28.5 5.46
40 18.2 3.68 19.7 4.29 21.4 5.00 23.3 5.63 24.0 5.77 24.9 5.91 25.6 6.02
35 80 18.2 3.39 19.7 4.01 21.4 4.68 23.3 5.27 24.0 5.40 24.9 5.54 25.6 5.65
100 18.2 3.29 19.7 3.93 21.4 4.58 23.3 5.16 24.0 5.30 24.9 5.43 25.6 5.52
40 16.1 3.88 17.5 4.53 19.0 5.28 20.7 5.94 21.3 6.08 22.2 6.23 22.8 6.34
40 80 16.1 3.57 17.5 4.23 19.0 4.93 20.7 5.55 21.3 5.69 22.2 5.84 22.8 5.96
100 16.1 3.47 17.5 4.14 19.0 4.83 20.7 5.45 21.3 5.59 22.2 5.73 22.8 5.83
40 19.5 1.94 21.1 2.26 23.0 2.64 25.0 2.97 25.7 3.04 26.7 3.12 27.5 3.17
15 80 19.5 1.79 21.1 2.12 23.0 2.47 25.0 2.78 25.7 2.85 26.7 2.92 27.5 2.98
100 19.5 1.74 21.1 2.07 23.0 2.42 25.0 2.72 25.7 2.79 26.7 2.86 27.5 2.91
40 19.3 2.37 20.9 2.76 22.7 3.21 24.7 3.62 25.5 3.71 26.4 3.80 27.2 3.86
20 80 19.3 2.18 20.9 2.58 22.7 3.00 24.7 3.38 25.5 3.47 26.4 3.56 27.2 3.63
100 19.3 2.12 20.9 2.52 22.7 2.94 24.7 3.32 25.5 3.40 26.4 3.49 27.2 3.54
40 19.3 2.91 20.9 3.39 22.7 3.95 24.7 4.45 25.5 4.55 26.4 4.67 27.2 4.75
25 80 19.3 2.67 20.9 3.17 22.7 3.69 24.7 4.16 25.5 4.26 26.4 4.37 27.2 4.46
100 19.3 2.60 20.9 3.10 22.7 3.62 24.7 4.08 25.5 4.18 26.4 4.29 27.2 4.35
40 19.3 3.51 20.9 4.10 22.7 4.78 24.7 5.38 25.5 5.51 26.4 5.64 27.2 5.74
120 30 80 19.3 3.23 20.9 3.83 22.7 4.47 24.7 5.03 25.5 5.15 26.4 5.29 27.2 5.39
100 19.3 3.14 20.9 3.75 22.7 4.37 24.7 4.93 25.5 5.06 26.4 5.19 27.2 5.26
40 17.6 3.60 19.1 4.20 20.8 4.90 22.6 5.51 23.3 5.64 24.2 5.78 24.9 5.89
35 80 17.6 3.31 19.1 3.93 20.8 4.58 22.6 5.15 23.3 5.28 24.2 5.42 24.9 5.52
100 17.6 3.22 19.1 3.85 20.8 4.48 22.6 5.05 23.3 5.18 24.2 5.31 24.9 5.39
40 16.0 3.88 17.3 4.52 18.9 5.27 20.5 5.93 21.1 6.07 22.0 6.22 22.6 6.34
40 80 16.0 3.57 17.3 4.23 18.9 4.93 20.5 5.55 21.1 5.68 22.0 5.83 22.6 5.94
100 16.0 3.47 17.3 4.14 18.9 4.82 20.5 5.44 21.1 5.58 22.0 5.72 22.6 5.80
40 18.5 1.85 20.0 2.16 21.8 2.52 23.7 2.83 24.4 2.90 25.3 2.97 26.1 3.03
15 80 18.5 1.70 20.0 2.02 21.8 2.35 23.7 2.65 24.4 2.71 25.3 2.79 26.1 2.84
100 18.5 1.66 20.0 1.98 21.8 2.31 23.7 2.60 24.4 2.66 25.3 2.73 26.1 2.77
40 18.4 2.27 19.9 2.65 21.7 3.09 23.6 3.47 24.3 3.56 25.2 3.64 25.9 3.71
20 80 18.4 2.09 19.9 2.48 21.7 2.88 23.6 3.25 24.3 3.33 25.2 3.41 25.9 3.48
100 18.4 2.03 19.9 2.42 21.7 2.83 23.6 3.18 24.3 3.27 25.2 3.35 25.9 3.39
40 18.4 2.78 19.9 3.24 21.7 3.78 23.6 4.25 24.3 4.36 25.2 4.46 25.9 4.54
25 80 18.4 2.56 19.9 3.03 21.7 3.53 23.6 3.98 24.3 4.07 25.2 4.18 25.9 4.26
100 18.4 2.49 19.9 2.97 21.7 3.46 23.6 3.90 24.3 4.00 25.2 4.10 25.9 4.15
40 18.4 3.39 19.9 3.95 21.7 4.61 23.6 5.19 24.3 5.31 25.2 5.44 25.9 5.54
110 30 80 18.4 3.12 19.9 3.70 21.7 4.31 23.6 4.85 24.3 4.97 25.2 5.10 25.9 5.19
100 18.4 3.03 19.9 3.62 21.7 4.22 23.6 4.75 24.3 4.87 25.2 5.00 25.9 5.06
40 17.1 3.52 18.5 4.11 20.2 4.79 22.0 5.39 22.6 5.52 23.5 5.66 24.1 5.76
35 80 17.1 3.24 18.5 3.84 20.2 4.48 22.0 5.04 22.6 5.16 23.5 5.30 24.1 5.40
100 17.1 3.15 18.5 3.76 20.2 4.39 22.0 4.94 22.6 5.07 23.5 5.20 24.1 5.26
40 15.9 3.87 17.2 4.52 18.7 5.26 20.3 5.92 21.0 6.06 21.8 6.21 22.4 6.33
40 80 15.9 3.56 17.2 4.22 18.7 4.92 20.3 5.54 21.0 5.67 21.8 5.82 22.4 5.93
100 15.9 3.46 17.2 4.13 18.7 4.82 20.3 5.43 21.0 5.57 21.8 5.71 22.4 5.78
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 54
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
55 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 56
Cooling Capacity(220V)
ARWN160BA2
TC:Total Capacity(kW)
PI :Power Input(kW)
57 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 58
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
59 Outside Units
ARWN240BA2
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 60
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
61 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 62
ARWN320BA2
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
63 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 64
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
65 Outside Units
ARWN400BA2
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 66
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
67 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 68
ARWN480BA2
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
69 Outside Units
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 70
Cooling Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
71 Outside Units
7.2.2 Heat Capacity
Heating Capacity(220V)
ARWN80BA2
Water Indoor Air Temperature(°CDB)
Inlet
Combination Water Flow 16 18 20 21 22 24
(%) Temperature Rate
TC PI TC PI TC PI TC PI TC PI TC PI
(°C) (L/min)
(kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW)
40 29.8 5.35 29.7 5.50 29.6 5.71 28.8 5.64 28.1 5.39 26.5 4.89
15 80 30.8 5.35 30.6 5.50 30.5 5.71 29.7 5.47 28.9 5.23 27.3 4.75
100 30.9 5.37 30.9 5.56 30.9 5.74 30.1 5.50 29.3 5.25 27.7 5.24
40 30.9 4.88 30.8 4.97 30.7 5.10 29.9 5.08 29.1 5.07 27.4 4.98
20 80 31.9 4.95 31.8 5.06 31.7 5.20 30.9 5.16 30.0 5.16 28.4 5.09
100 32.1 4.95 32.1 5.08 32.1 5.24 31.2 5.18 30.3 5.17 28.6 5.09
40 33.7 5.09 32.9 5.08 32.1 5.09 31.4 4.99 30.8 4.90 29.0 4.61
25 80 33.7 4.98 32.9 4.98 32.1 5.01 31.4 4.91 30.8 4.82 29.0 4.54
130 100 33.7 4.91 32.9 4.91 32.1 4.94 31.4 4.84 30.8 4.75 29.0 4.48
40 33.7 4.89 32.9 4.88 32.1 4.89 31.4 4.77 30.8 4.65 29.0 4.34
30 80 33.7 4.75 32.9 4.76 32.1 4.78 31.4 4.67 30.8 4.55 29.0 4.24
100 33.7 4.69 32.9 4.69 32.1 4.72 31.4 4.61 30.8 4.49 29.0 4.19
40 33.7 4.72 32.9 4.70 32.1 4.72 31.4 4.56 30.8 4.40 29.0 4.02
35 80 33.7 4.55 32.9 4.55 32.1 4.58 31.4 4.42 30.8 4.27 29.0 3.90
100 33.7 4.49 32.9 4.49 32.1 4.52 31.4 4.37 30.8 4.21 29.0 3.86
40 33.7 4.56 32.9 4.55 32.1 4.56 31.4 4.38 30.8 4.21 29.0 3.82
40 80 33.7 4.36 32.9 4.36 32.1 4.39 31.4 4.21 30.8 4.05 29.0 3.67
100 33.7 4.30 32.9 4.31 32.1 4.34 31.4 4.17 30.8 4.00 29.0 3.63
40 28.3 5.37 28.2 5.51 28.1 5.73 27.4 5.61 26.6 5.36 25.1 4.88
15 80 29.0 5.34 28.9 5.50 28.8 5.71 28.0 5.48 27.1 5.20 25.7 4.75
100 29.1 5.35 29.1 5.53 29.0 5.71 28.3 5.48 27.4 5.20 25.9 5.06
40 29.1 4.75 29.0 4.87 28.9 5.03 28.1 4.96 27.2 4.88 25.7 4.72
20 80 29.9 4.80 29.7 4.92 29.5 5.08 28.8 4.99 27.9 4.90 26.4 4.74
100 30.1 4.79 30.0 4.93 29.8 5.09 29.0 4.99 28.1 4.89 26.5 4.72
40 31.7 4.84 30.8 4.80 29.8 4.76 29.2 4.64 28.4 4.50 26.8 4.22
25 80 31.8 4.76 30.8 4.71 29.8 4.68 29.2 4.57 28.4 4.43 26.8 4.15
120 100 31.8 4.70 30.8 4.64 29.8 4.62 29.2 4.51 28.4 4.37 26.8 4.10
40 31.8 4.60 30.8 4.50 29.8 4.43 29.2 4.31 28.4 4.16 26.8 3.88
30 80 31.8 4.48 30.8 4.39 29.8 4.33 29.2 4.22 28.4 4.07 26.8 3.79
100 31.8 4.42 30.8 4.33 29.8 4.28 29.2 4.16 28.4 4.02 26.8 3.75
40 31.8 4.37 30.8 4.26 29.8 4.18 29.2 4.03 28.4 3.87 26.8 3.55
35 80 31.8 4.22 30.8 4.12 29.8 4.05 29.2 3.91 28.4 3.75 26.8 3.45
100 31.8 4.17 30.8 4.07 29.8 4.00 29.2 3.87 28.4 3.71 26.8 3.41
40 31.8 4.19 30.8 4.09 29.8 3.96 29.2 3.81 28.4 3.65 26.8 3.33
40 80 31.8 4.00 30.8 3.91 29.8 3.81 29.2 3.67 28.4 3.51 26.8 3.20
100 31.8 3.95 30.8 3.87 29.8 3.77 29.2 3.63 28.4 3.47 26.8 3.17
40 26.8 5.39 26.8 5.53 26.7 5.75 26.0 5.59 25.0 5.32 23.8 4.87
15 80 27.2 5.33 27.1 5.49 27.0 5.71 26.3 5.48 25.3 5.17 24.1 4.75
100 27.4 5.32 27.3 5.50 27.1 5.68 26.5 5.45 25.5 5.15 24.2 4.88
40 27.3 4.62 27.2 4.78 27.0 4.96 26.4 4.85 25.4 4.68 24.1 4.45
20 80 27.9 4.64 27.6 4.79 27.4 4.97 26.7 4.83 25.7 4.64 24.4 4.38
100 28.1 4.63 27.8 4.78 27.5 4.93 26.8 4.79 25.8 4.60 24.5 4.35
40 29.6 4.59 28.7 4.52 27.5 4.42 26.9 4.29 26.0 4.10 24.6 3.82
25 80 29.9 4.54 28.7 4.44 27.5 4.35 26.9 4.22 26.0 4.03 24.6 3.76
110 100 30.0 4.50 28.7 4.38 27.5 4.29 26.9 4.17 26.0 3.99 24.6 3.72
40 30.0 4.30 28.7 4.12 27.5 3.97 26.9 3.85 26.0 3.68 24.6 3.42
30 80 30.0 4.20 28.7 4.03 27.5 3.88 26.9 3.77 26.0 3.60 24.6 3.34
100 30.0 4.15 28.7 3.98 27.5 3.83 26.9 3.72 26.0 3.56 24.6 3.31
40 30.0 4.03 28.7 3.81 27.5 3.63 26.9 3.51 26.0 3.34 24.6 3.08
35 80 30.0 3.90 28.7 3.70 27.5 3.52 26.9 3.41 26.0 3.24 24.6 2.99
100 30.0 3.85 28.7 3.65 27.5 3.48 26.9 3.37 26.0 3.21 24.6 2.97
40 30.0 3.82 28.7 3.63 27.5 3.36 26.9 3.24 26.0 3.08 24.6 2.83
40 80 30.0 3.64 28.7 3.47 27.5 3.23 26.9 3.12 26.0 2.97 24.6 2.73
100 30.0 3.60 28.7 3.43 27.5 3.20 26.9 3.09 26.0 2.94 24.6 2.71
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 72
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
73 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 74
ARWN160BA2 Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
75 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 76
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
77 Outside Units
ARWN240BA2 Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 78
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
79 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 80
ARWN320BA2 Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
81 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 82
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
83 Outside Units
ARWN400BA2 Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 84
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
85 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 86
ARWN480BA2 Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
87 Outside Units
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
Outside Units 88
Heating Capacity(220V)
TC:Total Capacity(kW)
PI :Power Input(kW)
89 Outside Units
7.3 Capacity Correction Factor
ARWN100DA2, ARWN80BA2
Rate of change in cooling capacity
α
50 - - - - - - 0.92 0.90 0.89 0.88 0.86 0.85 0.84 0.83
40 - - - - - 0.93 0.92 0.90 0.89 0.88 0.87 0.85 0.84 0.83
HU 30 - - - - 0.95 0.93 0.92 0.91 0.89 0.88 0.87 0.85 0.84 0.83
(m) 20 - - - 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.84 0.83
10 - - 0.99 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.85 0.84
7.5 - 1.0 0.99 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.85 0.84
0 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.90 0.88 0.87 0.86 0.85 0.84
0 7.5 10 20 30 40 50 60 70 80 90 100 110 120 L(m)
0 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.90 0.88 0.87 0.86 0.85 0.84
7.5 - 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.90 0.88 0.87 0.86 0.85 0.84
HL 10 - - 0.99 0.98 0.96 0.94 0.93 0.91 0.90 0.88 0.87 0.86 0.85 0.84
(m) 20 - - - 0.98 0.96 0.94 0.93 0.91 0.90 0.88 0.87 0.86 0.85 0.84
30 - - - - 0.96 0.94 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84
40 - - - - - 0.95 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84
50 - - - - - - 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84 α
★ 1. Symbols
HU : Level difference between indoor and outside units where indoor unit in inferior position (m)
HL : Level difference between indoor and outside units where indoor unit in superior position (m)
L : Equivalent pipe length (m)
α : Capacity correction factor
2. These figures illustrate the rate of change in capacity of a standard indoor unit system at maximum load under standard conditions.
(Moreover, under partial load conditions there is only a minor deviation from the rate of change in capacity shown in the above figures.)
3. With this outside unit, evaporating pressure constant control when cooling, and condensing pressure constant control when heating is carried out.
4. If heat insulation of piping is insufficient, heat loss will become larger and capacity will decrease
5. Method of calculating cooling / heating capacity : maximum cooling / heating capacity of outside units
= cooling / heating capacity of outside units obtained from capacity table X capacity correction factor due to piping length to the farthest indoor unit
6. Assume equivalent pipe length of Y branch to be 0.5 m, that of header to be 1.0 m, calculation purposes.
7. When overall equivalent pipe length is 90 m or more, the diameter of the main gas and liquid pipes.
: gas pipe Ø22.2 → Ø25.4 liquid pipe Ø9.52 → Ø12.7
8. Read cooling / heating capacity rate of change in the above figures based on the following equivalent length.
: overall equivalent length = (equivalent length of main pipe) X correction factor + (equivalent length after first branching)
overall equivalent pipe length
correction factor
< 90 m ≥ 90 m
cooling 1.0 0.5
heating 1.0 0.2
Ex)
Outside Units 90
ARWN200DA2, ARWN160BA2
Rate of change in cooling capacity
α
50 - - - - - - 0.92 0.90 0.89 0.88 0.86 0.85 0.84 0.83
40 - - - - - 0.93 0.92 0.90 0.89 0.88 0.86 0.85 0.84 0.83
HU 30 - - - - 0.95 0.93 0.92 0.90 0.89 0.88 0.87 0.85 0.84 0.83
(m) 20 - - - 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.85 0.84 0.83
10 - - 0.99 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.84 0.83
7.5 - 1.0 0.99 0.97 0.95 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.84 0.83
0 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.85 0.84
0 7.5 10 20 30 40 50 60 70 80 90 100 110 120 L(m)
0 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.89 0.88 0.87 0.86 0.85 0.84
7.5 - 1.0 0.99 0.97 0.96 0.94 0.92 0.91 0.90 0.88 0.87 0.86 0.85 0.84
10 - - 0.99 0.98 0.96 0.94 0.92 0.91 0.90 0.88 0.87 0.86 0.85 0.84
HL
20 - - - 0.98 0.96 0.94 0.93 0.91 0.90 0.88 0.87 0.86 0.85 0.84
(m)
30 - - - - 0.96 0.94 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84
40 - - - - - 0.95 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84
50 - - - - - - 0.93 0.91 0.90 0.89 0.87 0.86 0.85 0.84 α
★ 1. Symbols
HU : Level difference between indoor and outside units where indoor unit in inferior position (m)
HL : Level difference between indoor and outside units where indoor unit in superior position (m)
L : Equivalent pipe length (m)
α : Capacity correction factor
2. These figures illustrate the rate of change in capacity of a standard indoor unit system at maximum load under standard conditions.
(Moreover, under partial load conditions there is only a minor deviation from the rate of change in capacity shown in the above figures.)
3. With this outside unit, evaporating pressure constant control when cooling, and condensing pressure constant control when heating is carried out.
4. If heat insulation of piping is insufficient, heat loss will become larger and capacity will decrease
5. Method of calculating cooling / heating capacity : maximum cooling / heating capacity of outside units
= cooling / heating capacity of outside units obtained from capacity table X capacity correction factor due to piping length to the farthest indoor unit
6. Assume equivalent pipe length of Y branch to be 0.5 m, that of header to be 1.0 m, calculation purposes.
7. When overall equivalent pipe length is 90 m or more, the diameter of the main gas and liquid pipes.
: gas pipe Ø28.58 → Ø31.8 liquid pipe Ø12.7 → Ø15.88
8. Read cooling / heating capacity rate of change in the above figures based on the following equivalent length.
: overall equivalent length = (equivalent length of main pipe) X correction factor + (equivalent length after first branching)
overall equivalent pipe length
correction factor
< 90 m ≥ 90 m
Cooling 1.0 0.5
Heating 1.0 0.3
Ex)
91 Outside Units
ARWN300DA2, ARWN240BA2
Rate of change in cooling capacity
α
50 - - - - - - 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85
40 - - - - - 0.94 0.93 0.91 0.90 0.89 0.88 0.87 0.86 0.85
HU 30 - - - - 0.95 0.94 0.93 0.91 0.90 0.89 0.88 0.87 0.86 0.85
(m) 20 - - - 0.97 0.96 0.94 0.93 0.91 0.90 0.89 0.88 0.87 0.86 0.85
10 - - 0.99 0.97 0.96 0.94 0.93 0.92 0.90 0.89 0.88 0.87 0.86 0.85
7.5 - 1.0 0.99 0.97 0.96 0.94 0.93 0.92 0.90 0.89 0.88 0.87 0.86 0.85
0 1.0 0.99 0.97 0.96 0.94 0.93 0.92 0.90 0.89 0.88 0.87 0.86 0.85
0 7.5 10 20 30 40 50 60 70 80 90 100 110 120 L(m)
0 1.0 0.99 0.97 0.96 0.94 0.93 0.92 0.90 0.89 0.88 0.87 0.86 0.85
7.5 - 1.0 0.99 0.98 0.96 0.95 0.93 0.92 0.91 0.89 0.88 0.87 0.86 0.85
HL 10 - - 0.99 0.98 0.96 0.95 0.93 0.92 0.91 0.89 0.88 0.87 0.86 0.85
(m) 20 - - - 0.98 0.96 0.95 0.93 0.92 0.91 0.90 0.88 0.87 0.86 0.85
30 - - - - 0.96 0.95 0.93 0.92 0.91 0.90 0.88 0.87 0.86 0.85
40 - - - - - 0.95 0.94 0.92 0.91 0.90 0.89 0.87 0.86 0.85
50 - - - - - - 0.94 0.92 0.91 0.90 0.89 0.87 0.86 0.85 α
α
50 - - - - - - 0.89 0.86 0.83 0.81 0.79 0.77 0.75
40 - - - - - 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
HU 30 - - - - 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
(m) 20 - - - 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
10 - - 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
7.5 - 1.0 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
0 1.0 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
0 7.5 10 20 30 40 50 60 70 80 90 100 110 L(m)
0 1.0 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
7.5 - 1.0 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
10 - - 1.0 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
HL 20 - - - 1.0 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
(m) 30 - - - - 0.97 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
40 - - - - - 0.92 0.89 0.86 0.83 0.81 0.79 0.77 0.75
50 - - - - - - 0.89 0.86 0.83 0.81 0.79 0.77 0.75 α
★ 1. Symbols
HU : Level difference between indoor and outside units where indoor unit in inferior position (m)
HL : Level difference between indoor and outside units where indoor unit in superior position (m)
L : Equivalent pipe length (m)
α : Capacity correction factor
2. These figures illustrate the rate of change in capacity of a standard indoor unit system at maximum load under standard conditions.
(Moreover, under partial load conditions there is only a minor deviation from the rate of change in capacity shown in the above figures.)
3. With this outside unit, evaporating pressure constant control when cooling, and condensing pressure constant control when heating is carried out.
4. If heat insulation of piping is insufficient, heat loss will become larger and capacity will decrease
5. Method of calculating cooling / heating capacity : maximum cooling / heating capacity of outside units
= cooling / heating capacity of outside units obtained from capacity table X capacity correction factor due to piping length to the farthest indoor unit
6. Assume equivalent pipe length of Y branch to be 0.5 m, that of header to be 1.0 m, calculation purposes.
7. When overall equivalent pipe length is 90 m or more, the diameter of the main gas and liquid pipes.
: gas pipe Ø34.9 → Ø38.1 liquid pipe Ø19.05 → Ø22.2
8. Read cooling / heating capacity rate of change in the above figures based on the following equivalent length.
: overall equivalent length = (equivalent length of main pipe) X correction factor + (equivalent length after first branching)
overall equivalent pipe length
correction factor
< 90 m ≥ 90 m
Cooling 1.0 0.5
Heating 1.0 0.4
Ex)
Outside Units 92
ARWN400DA2, ARWN500DA2, ARWN600DA2, ARWN320BA2, ARWN400BA2, ARWN480BA2
Rate of change in cooling capacity
α
50 - - - - - - 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.85 0.84 0.83 0.82
40 - - - - - 0.95 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.85 0.84 0.83 0.82
HU 30 - - - - 0.96 0.95 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.86 0.85 0.84 0.83 0.82
(m) 20 - - - 0.97 0.96 0.95 0.94 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.86 0.85 0.84 0.83 0.82
10 - - 0.99 0.97 0.96 0.95 0.94 0.93 0.91 0.90 0.89 0.88 0.87 0.87 0.86 0.85 0.84 0.83 0.82
7.5 - 0.99 0.99 0.98 0.96 0.95 0.94 0.93 0.91 0.90 0.89 0.88 0.87 0.87 0.86 0.85 0.84 0.83 0.82
0 1.0 0.99 0.98 0.96 0.95 0.94 0.93 0.92 0.90 0.89 0.88 0.88 0.87 0.86 0.85 0.84 0.83 0.82
0 7.5 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 175 L(m)
0 1.0 0.99 0.98 0.96 0.95 0.94 0.93 0.92 0.90 0.89 0.88 0.88 0.87 0.86 0.85 0.84 0.83 0.82
7.5 - 1.0 0.99 0.98 0.96 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82
HL 10 - - 0.99 0.98 0.96 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82
(m) 20 - - - 0.98 0.97 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82
30 - - - - 0.97 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.84 0.82
40 - - - - - 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.84 0.83
50 - - - - - - 0.94 0.93 0.92 0.91 0.90 0.89 0.88 0.87 0.86 0.85 0.84 0.84 0.83 α
★ 1. Symbols
HU : Level difference between indoor and outside units where indoor unit in inferior position (m)
HL : Level difference between indoor and outside units where indoor unit in superior position (m)
L : Equivalent pipe length (m)
α : Capacity correction factor
2. These figures illustrate the rate of change in capacity of a standard indoor unit system at maximum load under standard conditions.
(Moreover, under partial load conditions there is only a minor deviation from the rate of change in capacity shown in the above figures.)
3. With this outside unit, evaporating pressure constant control when cooling, and condensing pressure constant control when heating is carried out.
4. If heat insulation of piping is insufficient, heat loss will become larger and capacity will decrease
5. Method of calculating cooling / heating capacity : maximum cooling / heating capacity of outside units
= cooling / heating capacity of outside units obtained from capacity table X capacity correction factor due to piping length to the farthest indoor unit
6. Assume equivalent pipe length of Y branch to be 0.5 m, that of header to be 1.0 m, calculation purposes.
7. When overall equivalent pipe length is 90 m or more, the diameter of the main gas and liquid pipes.
: gas pipe Ø41.3 → Ø41.3 liquid pipe Ø19.05 → Ø22.2
8. Read cooling / heating capacity rate of change in the above figures based on the following equivalent length.
: overall equivalent length = (equivalent length of main pipe) X correction factor + (equivalent length after first branching)
overall equivalent pipe length
correction factor
< 90 m ≥ 90 m
Cooling 1.0 1.0
Heating 1.0 0.4
Ex)
93 Outside Units
8. Operation Limits
Cooling Heating
45 45
40 40
25 25
20 20
15 15
Range for Range for
operation operation
10 10
10 15 20 25 30 10 15 20 25 30
Notes:
These figures assume the following operating conditions:
Equivalent piping length:7.5m
Level difference:0m
Outside Units 94
9. Sound Levels
Unit:dB(A)
Model 460V, 60Hz
ARWN100DA2 51
ARWN200DA2 51
ARWN300DA2 53
ARWN400DA2 54
ARWN500DA2 55 1m
ARWN600DA2 56
Unit:dB(A) 1m
Model 220V, 60Hz
ARWN80BA2 49
ARWN160BA2 50 Notes:
ARWN240BA2 51 • Data is valid at free field condition
ARWN320BA2 52
• Data is valid at nominal operating condition
ARWN400BA2 53
• Sound level will vary depending on a range of factors such
ARWN480BA2 54
as the construction
(acoustic absorption coefficient) of particular room in which
the equipment is installed
• The operating conditions are assumed to be standard(ISO
conditions)
ARWN100DA2 ARWN200DA2 ARWN300DA2
80 80 80
70 70 70
Octave Band Sound Pressure Level (dB re 20µPa )
NC-55 NC-55
50 50 NC-55
50
NC-50 NC-50 NC-50
NC-45 NC-45
40 40 NC-45
40
NC-40 NC-40 NC-40
NC-35 NC-35
30 30 NC-35
30
NC-30 NC-30
NC-30
20 NC-25 20 NC-25
20 NC-25
Approximate Approximate
NC-20 NC-20 Approximate
Hearing Hearing NC-20
Hearing
Threshold NC-15 Threshold NC-15
10 10 Threshold NC-15
63 125 250 500 1000 2000 4000 8000 10
63 125 250 500 1000 2000 4000 8000
63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz) Octave Band Center Frequency (Hz)
Octave Band Center Frequency (Hz)
70 70 70
Octave Band Sound Pressure Level (dB re 20µPa )
95 Outside Units
ARWN80BA2 ARWN160BA2 ARWN240BA2
80 80 80
70 70 70
Octave Band Sound Pressure Level (dB re 20µPa )
70 70
70
Octave Band Sound Pressure Level (dB re 20µPa )
Outside Units 96
10. Accessories
Optional Accessories
ARBLN01621
ARBLN03321
1 Y branch pipe
ARBLN07121
ARBLN14521
ARBL054
ARBL057
ARBL104
2 Header
ARBL107
ARBL1010
ARBL2010
97 Outside Units
Installation of Outside Units
CAUTION
1. Do not install Multi V water outdoor. Always install indoor like machine room.
2. Inverter product may generate electric noise. Keep the body from computer, stereo etc. at
enough distance. Specially leave space from indoor remote controller to shoes electric devices
at the above 3m in weak electric wave area. Insert the power cable and other wire into separate
conduit.
1 Installation
2. Installation Space
2.1 Individual Installation
Required the minimum space as shown below for installation and
check. If the space is not fit on this drawing, consult with LG.
: Service area
20
(unit : mm)
100
Product
547
(Outside unit)
Water pipe
installation
1120
space
600
Service area
(Front)
350
100
20 772 H-Beam Support
100
<Top View> <Front View>
: Service area
(Unit : mm)
20
Product Product
547
350 350
20 772 772
100 100
<Top view>
Installation 2
: Service area
(Unit : mm)
20
Product Product Product
547
(Outside unit) (Outside unit) (Outside unit)
600
Service area Service area Service area
(Front) (Front) (Front)
* In case of the water pipe passing side product, please make sufficient service place to avoid occurring
between water pipe and product side.
3 Installation
2.3 Two Layer Installation
Space required for two layer installation as shown below considering passage for air and people.
: Service area
(unit : mm)
100
1120
100 100
1120
100
H-Beam Support
<Front View>
Installation 4
3. Water Control
3.1 Water control
• Keep the water temperature between 10~45°C. Other it may cause the breakdown.
- Standard water supply temperature is 30°C for Cooling and 20°C for heating.
• Properly control the water velocity. Otherwise it may cause the noise, pipe vibration or pipe contraction, expansion
according to the temperature. Use the same water pipe size connected with the product or more.
• Refer to the water source pipe diameter and water velocity table below. As the water velocity is fast, air bubble will
increase.
• Be careful of the water purity control. Otherwise it may cause the breakdown due to water pipe corrosion.
(Refer to 'Standard Table for Water Purity Control')
• In case the water temperature is above 40°C, it is good to prevent the corrosion by adding The anticorrosive agent.
• Install the pipe, valve and gauge sensor in the space where it is easy to maintain. Install the water valve in the low posi-
tion for drain, if required.
• Be careful not to let air in. If so, the water velocity will be unstable in the circulation, pump efficiency will also decrease
and may cause the piping vibration. Therefore, install the air purge where it may generate the air.
• Choose the following anti freezing methods. Otherwise, it will be dangerous for the pipe to break in the winter.
- Circulate the water with the pump before dropping the temperature.
- Keep the normal temperature by boiler.
- When the cooling tower is not operated for a long time, drain the water in the cooling tower.
- Use an anti-freeze.
- Refer to the additive amount about freezing temperature as in the table given below.
• In addition to anti freeze, it may cause the change of the pressure in the water system and the low performance of the
product.
• Make sure to use the closed cooling type tower.
When applying the open type cooling tower, use a middle heat exchanger to make the water supply system a closed
type system.
5 Installation
3.2 Standard table for water purity control
The water may contain many foreign substances and hence may influence the performance and lifetime of the product
due to the corrosion of the condenser and water pipe. (Use water source that complies with the below standard table for
water purity control.)
If you use water supply other than the tap water to supply the water for the cooling tower, you must do a water quality
inspection.
• If you use the closed cooling tower, the water quality must be controlled in accordance with the following standard
table.
If you do not control the water quality in accordance with the following standard water quality table, it can cause perfor-
mance deterioration to the air conditioner and severe problem to the product
[Reference]
(1) The "O" mark for corrosion and scale means that there is possibility of occurrence.
(2) When the water temperature is 40°C or above or when uncoated iron is exposed to the water, it can result in corrosion.
Therefore adding anti-corrosion agent or removing the air can be very effective.
(3) In case of using the closed type cooling tower, the cooling water and supplementing water must satisfy the water quality
criteria of closed type system in the table.
(4) Supplementing water and supplied water must be supplied with tap water, industrial water and underground water
excluding filtered water, neutral water, soft water etc.
(5) 15 items in the table are general causes of corrosion and scale.
Installation 6
4. Lifting Method
• When carrying the unit suspended, pass the ropes under the unit and use the two suspension points each
at the front and rear.
• Always lift the unit with ropes attached at fours points so that impact is not applied to the unit.
• Attach the ropes to the unit at an angle of 40° or less
Sub line
A 40° or less
B Rope supporter WARNING
CAUTION
• Do not have only one person carry product if it is more than 20kg.
• PP bands are used to pack some products. Do not use them as a means for transportation because they
are dangerous.
• Tear the plastic packaging bag and scrap it so that children cannot play with it. Otherwise plastic pack-
aging bag may suffocate children.
• When carrying in outside unit, be sure to support it at four points. Carrying in and lifting with 3-point sup-
port may make outside unit unstable, resulting in a fall of it.
• When carrying with the forklift, be careful not to drop the product.
7 Installation
5. Installation
5.1 Location of anchor bolt
(Unit: mm)
59
50 658
13
599
The location of
anchor bolt
WARNING
• Be sure to install unit in a place strong enough to withstand its weight.
Any lack of strength may cause unit to fall down, resulting in a personal injury.
• Have installation work in order to protect against a strong wind and earthquake. Any installation defi-
ciency may cause unit to fall down, resulting in a personal injury.
• Especially take care for support strength of the floor surface, water drain processing (processing of
water flown out from the outside unit during operation) and paths of the pipe and wiring when making
a base support.
Installation 8
5.2 Preparation of Piping
Main cause of gas leakage is defect in flaring work. Carry out correct flaring work in the following procedure.
3) Flaring work
Handle
■ Carry out flaring work using flaring tool as shown below.
Bar Bar
Indoor unit Pipe "A" "A" Yoke
[kW(Btu/h] Gas Liquid Gas Liquid
Cone
≤5.6(19,100) Ø12.7 Ø6.35 1.6~1.8 1.1~1.3
<16.0(54,600) Ø15.88 Ø9.52 1.6~1.8 1.5~1.7
≤22.4(76,400) Ø19.05 Ø9.52 1.9~2.1 1.5~1.7 Copper pipe
9 Installation
5) Pipe connection
1. Follow the pipe path. Bend the pipe more than 3 times in 1 location and do not bend in the opposite direction. (This will
strengthen the pipe.)
2. After deforming the pipe, align the union fitting and center of the pipe, and tighten it with the wrench.
3. Connect the pipe to the service valve of the outside unit.
4. After finishing the piping work, check if there is any gas leakage
5. For the flare nut, always use the material that complies with Standard or better.
6. After completing the connection of the pipe, vacuum dry the indoor unit and the connecting pipe.
For the vacuum drying, you must use service ports of both the gas and liquid pipes.
CAUTION
When using two wrenches, tighten at regulated torque
* For the pipe connection, use the method of connecting the end of the pipe to the branch pipe. The refrigerant pipe
coming out from the outside unit is branched out at the end and is individually connected to the indoor unit.
WARNING
• Always be careful not to leak the refrigerant during the welding.
• When the refrigerant is combusted, it generates a toxic poisonous gas.
• Do not execute the welding work in a closed location.
• Always do a leakage test after welding the pipes.
WARNING
After completing work, securely tighten both service ports and caps so that gas does not leak.
Installation 10
* High/low pressure side is the ball valve that is opened and closed
by 1/4 rotation
Pipe joint (auxiliary parts): Securely perform brazing with a nitro-
gen blow into the service valve port.(Releasing pressure : 0.02
MPa or less)
Flare nut: Loose or tighten flare nut by using the wrench with
both ends. Coat the flare connection part with oil for the com-
pressor.
Cap: Remove caps and operate valve, etc. After operation,
always reattach caps (tightening torque of valve cap: 25Nm
(250kg-cm) or more). (Don't remove the internal part of the port)
Service port: Make the refrigerant pipe vacuum and charge it
using the service port. Always reattach caps after completing
work (tightening torque of service cap: 14Nm (140kg-cm) or
more).
Liquid pipe Ball Valve(Liquid Pipe)
Gas pipe
Elbow joint (field supply) Elbow
CAUTION
After installing the pipe, block the pipe escape of front and side panel. (It can cause mouse or other animals to enter and
cause damage to the wire.)
6) Heat Insulation
1. Use the heat insulation material for the refrigerant Fastening band
(accessory)
piping which has an excellent heat-resistance (Over
120°C)
2. When installing in a humid environment, use thicker
heat insulation material.
* Consult with LG on detailed technical specification. Refrigerant piping
Indoor unit
Thermal insulator
(accessory)
11 Installation
7) Standard refrigerant pipe EPDM heat insulation material thickness
* Note 1) General location: When the pipe passes through indoors in which the indoor unit is operated
- Apartment, classroom, office, mall, hospital, office-tel etc.
Note 2) Special location
1. When the location is air conditioned but has severe temperature/humidity difference due to high ceiling
- Church, auditorium, theater, lobby etc.
2. When the location is air conditioned but the internal temperature/humidity of the ceiling finishing is high
- Bathroom/swimming pool locker room etc. (Building with roof ceiling of sandwich assembly type)
Note 3) General location: When the pipe passes indoors where the indoor unit is not operated
- Hall way etc. (Dormitory, school, office-tel)
Note 4) Negative condition: When below conditions 1 and 2 are met.
1. When the pipe passes indoors where the indoor unit is not operated
2. When the humidity is high, regionally, and there is no air flow in the pipe passing area
- When installing the outside unit within the outside pipe tray or at a location where it is ok to have
freezes, apply 13t.
- If you are not sure with the selection of heat insulation material, coordinate with the supervision or
HQ.
- The thickness of the above heat insulation material is based on the heat conductivity of
0.088W/m°C.
Installation 12
8) Connection of high/low pressure common pipe
Slave2
Outside
Slave Unit
Outside Unit Slave1
Outside
Unit
Main
Outside Unit
Master
Outside Unit
1. For the high/low pressure common pipe, connect both master outside unit and slave outside units to the pipe by using
elbows.
2. For cutting the pipe, connect the high/low pressure common pipe after removing burrs, dusts and foreign material within the
pipe. Otherwise, the product may not operate due to sludge within the pipe.
3. For the working part leakage test, apply the nitrogen gas pressure of 3.8MPa (38.7kgf/cm2).
4. The vacuum criteria is to maintain the vacuum level to less than 5 Torr 1 hour after reaching 5 Torr. (Execute the vacuum
work again when it is below the criteria.)
5. Open the valve with the hexagon wrench.
13 Installation
9) Connecting branch pipe between outside units
2 Outside Units
(unit : mm)
Connecting
Combination specification Gas pipe Liquid pipe
branch pipe
Execute the welding
while pouring
nitrogen
Do not cut for
70mm or less I.D12.7
I.D9.52 I.D19.05 I.D12.7
24
I.D28.58 I.D28.58
I.D28.58 I.D34.9 I.D15.88
I.D19.05 I.D12.7 331
38 401
ARCNN20 I.D31.8
I.D22.2 363
473
I.D22.2
I.D15.88 I.D19.05 I.D19.05 O.D28.58 O.D34.9 I.D38.1 I.D9.52 O.D12.7 I.D19.05 I.D22.2
75 115 83 73 80
3 Outside Units
(unit : mm)
Connecting
Combination specification Gas pipe Liquid pipe
branch pipe
Blow nitrogen
while brazing
I.D12.7 I.D19.05
Don't cut the pipe less
I.D12.7
I.D9.52
than 70mm
I.D28.58 I.D28.58 I.D28.58 24
I.D19.05 I.D34.9
331 I.D15.88
38 I.D12.7
ARCNN20 401
363 I.D31.8
I.D22.2
473
I.D22.2
I.D15.88 I.D19.05 I.D19.05 O.D28.58 O.D34.9 I.D38.1 I.D9.52 O.D12.7 I.D19.05 I.D22.2
75 115 83 73 80
Blow nitrogen
Don't cut the pipe less while brazing
than 70mm
I.D15.88 I.D12.7 I.D19.05
24
I.D28.58
I.D34.9 I.D41.3
I.D12.7 I.D22.2
ARCNN30 45 I.D19.05 289
397
73
115
CAUTION
When installing the branch pipe vertically between the outside units, the refrigerant can be uneven
between the outside units, leading to compressor burn and reduced capacity
Installation 14
10) Installation of water pipe
1. Water pipe system diagram
• The water pressure resistance of the water pipe system of this product is 1.98MPa
• When the water pipe passes indoors, make sure to execute heat insulation on the pipe so that water drops do not form on the
outer side of the water pipe.
• The size of the drain pipe must be equal to or larger than the diameter of the connecting product.
- Always install a trap so that the drained water does not back flush.
• Always install a strainer (50Mesh or above) at the entrance of the water pipe. (When sand, trash, rusted pieces get mixed into
the water supply, it can cause problems to the product due to blocking)
- If On/Off valve is applied, by interlocking with outside unit, it can save the energy consumption of pump by blocking the
water supply to the outside unit not operating. Select appropriate valve and install on site if necessary.
• Install a pressure gauge and temperature gauge at the inlet and outlet of the water pipe.
• Flexible joints must be installed not to cause any leakage from the vibration of pipes.
• Install a service port to clean the heat exchanger at the each end of the water inlet and outlet.
• For the components of the water pipe system, always use components above the designed water pressure.
Water pipe
Inlet Strainer
CAUTION
Do not directly connect the drain outlet to the water pipe outlet.
(It can cause problems to the product.)
15 Installation
Pipe thickness Shear stress Tensile stress Bending moment Torque
Installation 16
6. Device protection unit
6.1 Strainer on water pipe
To protect the water cooling type product, you must install a strainer with 50 mesh or more on the heat water supply pipe.
If not installed, it can result in damage of heat exchanger by the following situation.
1. Heat water supply within the plate type heat exchanger is composed of multiple small paths.
2. If you do not use a strainer with 50 mesh or more, alien particles can partially block the water paths.
3. When running the heater, the plate type heat exchanger plays the role of the evaporator, and at this time, the temperature of
the coolant side drops to drop the temperature of the heat water supply, which can result in icing point in the water paths.
4. And as the heating process progresses, the water paths can be partially frozen to lead to damage in plate type heat
exchanger.
5. As a result of the damage of the heat exchanger from the freezing, the coolant side and the heat water source side will be
mixed to make the product unusable.
Cover
6.2 Flow switch work
Micro-switch
• It is recommended to install the flow switch to the water collection pipe system Adjustment screw
connecting to the outside unit. Vibration plate
(Flow switch acts as the 1st protection device when the heat water is not supplied. Bellows
If a certain level of water does not flow after installing the flow switch, an error sign
1 inch or
of CH24 error will be displayed on the product and the product will stop operating.) 3/4 inch
• When setting the flow switch, it is recommended to use the product with default socket
set value to satisfy the minimum flow rate of this product. (The minimum flow rate
range of this product is 50%. Reference flow rate : 10HP – 96LPM, 20HP –
192LPM
• Select the flow switch with the permitted pressure specification considering the
Pad
pressure specification of the heat water supply system. (But, the flow switch must
be for AC250V.)
CAUTION
• If the set value does not satisfy the minimum flow rate or if the set value is changed by the user arbitrarily, it can result
in product performance deterioration or serious product problem.
• If the product is operated with the heat water supply not flowing smoothly, it can damage the heat exchanger or cause
serious product problems.
• In case of CH24 or CH180 error, there is a possibility that the plate type heat exchanger is partially frozen inside. In this
case resolve the issue of partial freezing and then operate the product again. (Cause of partial freezing : Insufficient
heat water flux, water not supplied, insufficient coolant, alien particle penetrated inside plate type heat exchanger)
17 Installation
6.3 Installation of flow switch
• The flow switch must be installed at the horizontal pipe of the heat water supply out-
let of the product and check the direction of the heat water flow before the installa-
tion. (Picture 1)
• When connecting the flow switch to the product, remove the jump wire to connect to
the communication terminal (5(A) and 5(B)) of the outside unit control box. (Picture
2, 3) (Open the cover of the flow switch and check the wiring diagram before con- Picture 1
necting the wires. The wiring method can differ by the manufacturer of the flow
switch.)
• If necessary, adjust the flow rate detection screw after consulting with an expert and
adjust to the minimum flow rate range. (Picture 4) (Minimum flow rate range of this
product is 50%. Adjust the flow switch to touch the contact point when the flow rate
reaches 50% of the flow rate.)
- Reference flow rate : 10HP – 96LPM, 20HP – 192LPM)
Picture 2
Picture 3
Picture 4
CAUTION
• When the product operates while the flow switch touches the contact point at the flow rate range out of the permitted
range, it can cause product performance deterioration or serious product problem.
• Must use the normal closed type flow switch
- Circuit of outside unit is normal closed type
Installation 18
7. Refrigerant Piping System
7.1 Y branch method
7.1.1 When installing 1 outside unit
independently
Indoor unit
Ex) 5 indoor units connected direction
: Outside unit
: 1st branch (Y branch)
: Indoor units
: Indoor unit direction
Below H 50 m
L Below 150 m
l Below 40 m
➲ Outside unit ~ 1st branch :
Main pipe diameter (A)
Outside unit capacity Liquid pipe (mm) Gas pipe (mm)
8 HP Ø9.52 Ø22.2 Below 15 m
10 HP Ø9.52 Ø22.2
16 HP Ø12.7 Ø28.58
20 HP Ø12.7 Ø28.58
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe
with the pipe diameter (B) after 1st branching that is the same as the main pipe diameter (A).
Ex) When connecting with 120% of the indoor unit to 10 HP
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52(Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 9.52 (Liquid pipe) of main pipe diameter (A).
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must
change the main pipe diameter according to the outside unit capacity in accordance with the following table. (This
applies to both the liquid and gas pipes.)
19 Installation
7.1.2 When installing 2 outside units Slave
Below H 50 m
units: ARCNN20( ) l Below 40 m
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe with the pipe diameter (B)
after 1st branching that is the same as the main pipe diameter (A).
Ex) When connecting with 120% of the indoor unit to 10 HP.
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52(Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 9.52 (Liquid pipe) of main pipe diameter (A).
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change the main pipe diame-
ter according to the outside unit capacity in accordance with the following table. (This applies to both the liquid and gas pipes.)
Gas Pipe Liquid Pipe
24,30HP .......................................Ø37.9 → Ø38.1 24,30,32,40HP............................. Ø19.05 → Ø22.2
32,40HP .......................................Ø41.3
Installation 20
7.1.3 When installing 3 outside units
Slave2
Ex) 5 Indoor Units connected Slave1
direction
: Indoor Units
: Downward Indoor Unit
: Connection branch pipe between
Outside units:ARCNN30
: Connection branch pipe between L150m
Outside units:ARCNN20 l 40m
H 50m
➲ Slave2 outside unit ~ Connecting
branch pipe : Pipe diameter
between outside units (F)
Low/high pressure
Liquid pipe (mm) Gas pipe (mm)
common pipe ➲ Connecting branch pipe ~ 1st
Ø9.52/12.7 Ø22.2/28.58 Ø19.05
branch part : Main pipe diameter (A)
➲ Slave1 outside unit ~ Connecting Outside unit capacity Liquid pipe (mm) Gas pipe (mm)
40,48,50,60HP Ø19.05 Ø41.3
branch pipe : Pipe diameter
between outside units (E) ➲ Refrigerant pipe diameter from branch
Liquid pipe (mm) Gas pipe (mm)
Low/high pressure to branch (B, C, D)
common pipe
Total capacity of indoor
Ø15.88/19.05 Ø34.9/41.3 Ø19.05
units connected to after Liquid pipe Gas pipe
branching (kW) (mm) (mm)
➲ Total refrigerant pipe length = ≤ 5.6 Ø6.35 Ø12.7
A + B + C + D + a + b + c + d + e ≤ 300 m < 16 Ø9.52 Ø15.88
≤ 22.4 Ø9.52 Ø19.05
L Longest pipe length (Equivalent pipe length)
< 33 Ø9.52 Ø22.2
A + B + C + D + e 150 m(175 m)
Longest pipe length after 1st branching < 47 Ø12.7 Ø28.58
B + C + D + e 40 m < 71 Ø15.88 Ø28.58
High/Low difference (Outside unit ↔ Indoor unit) < 104 Ø19.05 Ø34.9
H 104 ≤ Ø19.05 Ø41.3
H 50 m
High/Low difference (Indoor unit ↔ Indoor unit)
h h 15 m For the first branch pipe (B), use the branch pipe
High/Low difference (Outside unit ↔ Outside unit) that fits the main pipe diameter (A).
h1 h 2 m
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe with the pipe diameter (B)
after 1st branching that is the same as the main pipe diameter (A).
Ex) When connecting with 120% of the indoor unit to 10 HP.
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52(Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 9.52 (Liquid pipe) of main pipe diameter (A).
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change the main pipe diame-
ter according to the outside unit capacity in accordance with the following table. (This applies to both the liquid and gas pipes.)
Gas Pipe Liquid Pipe
40,48,50,60HP .............................Ø41.3 40,48,50,60HP.............................Ø19.05 → Ø22.2
21 Installation
7.2 Header branch method
7.2.1 When installing 1 outside unit
independently
Ex) 6 indoor units connected
Outside unit
Header branch
Indoor unit
Seal
L Below 150 m
Below H 50 m
➲ Outside unit ~ Header branch l Below 40 m
WARNING
• For the pipe length after the header branch (a~f), it is recommended to install the unit so that the difference of the pipe dis-
tance connected to the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change the
main pipe diameter according to the outside unit capacity in accordance with the following table.
(This applies to both the liquid and gas pipes.)
Installation 22
7.2.2 When installing 2 outside units
Slave
: Header branch
Below 2m
: Indoor unit
: Seal Below 10m
Below H 50 m
units: ARCNN20( ) l Below 40 m
➲ Slave outside unit ~ Connecting
branch unit : Pipe diameter
between outside units (E)
Below 15 m
Low/high pressure
Liquid pipe (mm) Gas pipe (mm)
common pipe
Ø9.52/12.7 Ø22.2/28.58 Ø19.05
➲ Connecting branch pipe ~ Header branch part : Main pipe diameter (A)
Outside unit capacity Liquid pipe (mm) Gas pipe (mm)
24,30HP Ø19.05 Ø34.9
32,40HP Ø19.05 Ø41.3
WARNING
• For the pipe length after the header branch (a~f), it is recommended to install the unit so that the difference of the pipe dis-
tance connected to the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change the
main pipe diameter according to the outside unit capacity in accordance with the following table. (This applies to both the liq-
uid and gas pipes.)
23 Installation
7.2.3 When installing 3 outside units Slave2
Slave1
Ex) 6 Indoor Units connected Master
: Outside Unit Below 2m
(h1)
: Header branch
: Indoor Units 10m or
less
: Sealing
: Connection branch pipe between
Outside units:ARCNN30
L150m
: Connection branch pipe between
H Below 50m
Outside units:ARCNN20 l 40m
WARNING
• For the pipe length after the header branch (a~f), it is recommended to install the unit so that the difference of the pipe distance connected to
the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change the main pipe diame-
ter according to the outside unit capacity in accordance with the following table. (This applies to both the liquid and gas pipes.)
Gas Pipe Liquid Pipe
40,48,50,60HP .............................Ø41.3 40,48,50,60HP.............................Ø19.05 → Ø22.2
Installation 24
7.3 Y/Header branch method
7.3.1 When installing 1 outside unit inde-
pendently
Ex) 5 indoor units connected
: Outside unit
: 1st Y branch
: 2nd Y branch
: Indoor unit
Below H 50 m
: Header branch
: Seal L Below 150 m
h Below 15 m
➲ Outside unit ~ 1st Y branch l Below 40 m
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe with
the pipe diameter (B) after 1st branching that is the same as the main pipe diameter (A). Ex) When connecting with 120%
of the indoor unit to 10 HP.
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52 (Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 9.52 (Liquid pipe) of main pipe diameter (A).
• For the pipe length after the header branch (c~e), it is recommended to install the unit so that the difference of the pipe
distance connected to the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must change
the main pipe diameter according to the outside unit capacity in accordance with the following table. (This applies to both
the liquid and gas pipes.)
Gas Pipe Liquid Pipe
8, 10 HP .......................................Ø22.2 → Ø25.4 8, 10 HP.......................................Ø9.52 → Ø12.7
16, 20 HP .....................................Ø28.58→ Ø31.8 16, 20 HP.....................................Ø12.7 → Ø15.88
25 Installation
7.3.2 When installing 2 outside units Slave
Ex) 5 indoor units connected
: Outside unit
Master
: 1st Y branch
: 2nd Y branch Below 2m
: Indoor unit
: Header branch Below 10m
: Seal
: Connecting branch pipe between outside units
❈ Connecting branch pipe between outside units:
ARCNN20( )
H Below 50 m
➲ Slave outside unit ~ Connecting L Below 150 m
h Below 15 m
branch pipe : Pipe diameter l Below 40 m
between outside units (E)
Low/high pressure
Liquid pipe (mm) Gas pipe (mm)
common pipe
Ø9.52/12.7 Ø22.2/28.58 Ø19.05
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe
with the pipe diameter (B) after 1st branching that is the same as the main pipe diameter (A).
Ex) When connecting with 120% of the indoor unit to 10 HP.
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52 (Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 952 (Liquid pipe) of main pipe diameter (A).
• For the pipe length after the header branch (c~e), it is recommended to install the unit so that the difference of the pipe
distance connected to the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must
change the main pipe diameter according to the outside unit capacity in accordance with the following table. (This
applies to both the liquid and gas pipes.)
Gas Pipe Liquid Pipe
24,30HP .......................................Ø37.9 → Ø38.1 24,30,32,40HP.............................Ø19.05 → Ø22.2
32,40HP .......................................Ø41.3
Installation 26
7.3.3 When installing 3 outside units
Ex) 5 Indoor Units connected Slave2
: Outside Unit Slave1
: 1st branch(Y branch) Master
w 2m
Below
: Y branch (h1)
: Indoor Unit
10m or
: Connection branch pipe between Outside less
units:ARCNN30
: Connection branch pipe between Outside
units:ARCNN20
: Header
: Sealing
H Below 50m
L150m
27 Installation
WARNING
• When the pipe diameter (B) connected after 1st branching is larger than the main pipe diameter (A), Install the pipe
with the pipe diameter (B) after 1st branching that is the same as the main pipe diameter (A).
Ex) When connecting with 120% of the indoor unit to 10 HP.
1) Outside unit main pipe diameter: 22.2 (Gas pipe) / 9.52 (Liquid pipe)
2) Pipe diameter after 1st branching by 120% indoor unit combination : 28.58 (Gas pipe) / 12.7 (Liquid pipe)
Therefore set the pipe diameter (B) after 1st branching to 22.2 (Gas pipe) / 952 (Liquid pipe) of main pipe diameter (A).
• For the pipe length after the header branch (c~e), it is recommended to install the unit so that the difference of the pipe
distance connected to the indoor unit is minimized.
• The large difference in pipe distance can cause performance difference between indoor units.
• After the header branch, you cannot use the Y branch and header branch.
• When the pipe distance corresponding to the farthest indoor unit from the outside unit is 90m or above, you must
change the main pipe diameter according to the outside unit capacity in accordance with the following table. (This
applies to both the liquid and gas pipes.)
Installation 28
7.5 Oil trap application method between outside units
• Because of the possibility of oil being accumulated in the outside unit that has stopped, when there is a height difference between
outside unit pipes or if the pipe distance between the outside units is over 2m, you must always apply an oil trap. (But, the oil trap
between outside units is limited to 1 time and is only applied to the gas pipe.)
• If the pipe distance between the outside units is 2m or below, and if the location of the main pipe is lower than that of the outside
unit and if the location of the main pipe is lower than that of the outside unit, the oil trap does not have to be applied.
• If the location of the main pipe is higher than the location of the outside unit, be careful since the oil can be accumulated in the
stopped outside unit.
• If there is high/low difference between the outside unit pipes, oil can be accumulated to the outside unit on the lower location until
the unit stops.
• When pipe distance between the outside units • Example of incorrect installation
is 2m or less Location of main pipe
High/Low difference
between the outside units
Oil is accumulated on the
outside unit because it can-
not be poured out from the
bottom of the pipe.
Location of
outside unit
Location of
main pipe 2m or less
Over 2m
Oil trap
High/Low difference
between outside
unit pipes
Oil trap
Location of
outside unit
Location of
main pipe 2m or less
29 Installation
7.6 Calculation of amount of refrigerant
The calculation of the additional charge should take account of the diameter and length of the pipe.
A Product Charge(kg)
Ex) 10HP
B Additional charge (kg)
Outside unit
= Total liquid pipe (m): Ø22.2mm x 0.354(kg/m) Header branch
Indoor unit
+ Total liquid pipe (m): Ø19.05mm x 0.266(kg/m)
CF(kg)
+ (Correction Factor)
Total amount(kg) = A + B
Additional Charge = A x 0.061 + B x 0.061 + C x 0.061
CAUTION If a negative result is obtained from + D x 0.061 + E x 0.022 + CF
the calculation, no refrigerant needs = 50 x 0.061 + 10 x 0.061 + 10 x 0.061
to be added. + 10 x 0.061 + 10 x 0.022 + 0(CF)
= 5.1kg
◆ Special condition
In case of the No. of CST TQ/RAC SE/ARTCOOL SF models are over than 50% of the connected
indoor units when the total No. of connected indoor units are over than 50% of the max. connectable
indoor units.
Total amount(kg) = A + B + C
■ Additional refrigerant charging amount (kg) :
= (A x + B x ß) - (AVG x ß)
• A = Total No. of TQ, SE and SF Indoor units, = 0.5
• B = Total No. of except TQ, SE and SF Indoor units, ß = 0.3
• AVG = 50% of Max. No. of connectable Indoor units.
Example)
1) Installation Information
- Outside unit : 10HP
- Total indoor units : 6 units (TQ 3 units, SE 2 units, BH 1 unit)
2) Information from PDB
- Max. No. of connectable indoor units : 16 units
- Calculated additional refrigerant amount = 2 kg :
3) Indoor refrigerant charging amount
= (5 units x 0.5+1 unit x 0.3) - (8 units x 0.3) = 0.4 kg :
Revised the total additional charging amount = = 2 kg + 0.4 kg
= 2.4 kg
Installation 30
Note:
Fill in the f-gas Label attached on outside about the quantity of the fluorinated greenhouse gases
Manufacturing site (See Model Name label)
Installation site (If possible being placed adjacent to the service points for the addition or removal of
refrigerant)
The total Charge ( + )
WARNING
Regulation for refrigerant leakage
: the amount of refrigerant leakage should satisfy the following equation for human safety.
If the above equation cannot be satisfied, the following steps must be followed.
- Selection of air conditioning system: Select one of the following
1. Installation of effective opening part: At the top and bottom of the door connecting the room to the outside, create an opening
with or without the door of with 0.15% of floor space or above.
2. Recheck of outside unit capacity and piping length
3. Reduction of the amount of refrigerant
4. Installation of 2 or more security devices (Alarm for gas leakage)
- Change indoor unit type
: Installation position should be over 2m from the floor (Wall mounted type → cassette type)
- Adoption of ventilation system
Ventilation system prevents the refrigerant density from increasing when the refrigerant is leaked by the installation.
Ventilation system comes in two types; external air inflow type or exhaust type. External air inflow type is recommended due to
the characteristics of the refrigerant.
Always operate the ventilation system irrelevant from whether the air conditioner is used or not and whether the indoor or not.
When it is impossible to operate this and in case of a refrigerant leakage by the sensor, the ventilation system is automatically
operated.
- Limitation in piping work
: Prepare for earthquake and thermal stress
- Reduction of all refrigerant charge amount of the refrigerant facility (When calculated value exceeds 0.44kg/m3)
1. Shorten the refrigerant pipe length.
Change the location of the outside unit and shorten the length of the refrigerant pipe to reduce all refrigerant charge amount.
2. Distribute the outside unit to several units to reduce the refrigerant charge amount per outside unit. (Ex. 20 HP 1 unit →
10 HP 2 units)
31 Installation
7.7 Refrigerant pipe fitting
7.7.1 Caution
1. Use the following materials for refrigerant piping.
• Material: Seamless phosphorous deoxidized copper pipe
• Wall thickness : Comply with the relevant local and national regulations for the designed pressure
3.8MPa. We recommend the following table as the minimum wall thickness.
Outer diameter
6.35 9.52 12.7 15.88 19.05 22.2 25.4 28.58 31.8 34.9 38.1 41.3
[mm]
Minimum
0.8 0.8 0.8 0.99 0.99 0.99 0.99 0.99 1.1 1.21 1.35 1.43
thickness [mm]
2. Commercially available piping often contains dust and other materials. Always blow it clean with a dry inert gas.
3. Use care to prevent dust, water or other contaminants from entering the piping during installation.
4. Reduce the number of bending portions as much as possible, and make bending radius as big as possible.
5. Always use the branch piping set shown below, which are sold separately.
Header
Y branch
4 branch 7 branch 10 branch
ARBLN01621 ARBLN03321 ARBL054 ARBL057 ARBL1010
ARBLN07121 ARBLN14521 ARBL104 ARBL107 ARBL2010
6. If the diameters of the branch piping of the designated refrigerant piping differs, use a pipe cutter to cut the connecting sec-
tion and then use an adapter for connecting different diameters to connect the piping.
7. Always observe the restrictions on the refrigerant piping (such as rated length, difference in height, and piping diameter).
Failure to do so can result in equipment failure or a decline in heating/cooling performance.
8. A second branch cannot be made after a header. (These are shown by .)
A A
A To Outside Unit
B Sealed Piping
9. The system will stop due to an abnormality like excessive or insufficient refrigerant. At such a time, always properly charge
the unit. When servicing, always check the notes concerning both the piping length and the amount of additional refrigerant.
10. Never perform a pump down. This will not only damage the compressor but also deteriorate the performance.
11. Never use refrigerant to perform an air purge. Always evacuate using a vacuum pump.
12. Always insulate the piping properly. Insufficient insulation will result in a decline in heating/cooling performance, drip of con-
densate and other such problems.
13. When connecting the refrigerant piping, make sure the service valves of the outside unit is completely closed (the factory
setting) and do not operate it until the refrigerant piping for the outside and indoor units has been connected, a refrigerant
leakage test has been performed and the evacuation process has been completed.
14. Always use a non-oxidizing brazing material for brazing the parts and do not use flux. If not, oxidized film can cause clog-
ging or damage to the compressors and flux can harm the copper piping or refrigerant oil.
Installation 32
7.7.2 Y Branch and Header Fitting
Y branch
B A To Outdoor Unit
A B To Branch Piping or Indoor Unit
• Ensure that the branch pipes are attached horizontally or vertically (see the diagram below.)
A
Viewed from point A
in direction of arrow
Within ± 3° Within ± 3°
C Pipe cutter
33 Installation
• When the number of indoor units to be connected to the branch pipes is less than the number of branch
pipes available for connection then cap pipes should be fitted to the surplus branches.
B
Piched pipe
Horizontal plane
• Joints between branch and pipe should be sealed with the tape included in each kit.
Tape
Insulator
• Any cap pipe should be insulated using the insulator provided with each kit and then taped as described
above.
Insulator for cap pipe
Cap pipe
Tape
Installation 34
7.7.3 Thermal insulation of refrigerant piping
Be sure to give insulation work to refrigerant piping by covering liquid pipe and gas pipe separately with
enough thickness heat-resistant polyethylene, so that no gap is observed in the joint between indoor unit
and insulating material, and insulating materials themselves. When insulation work is insufficient, there is a
possibility of condensation drip, etc. Pay special attention to insulation work to ceiling plenum.
B A C
Heat
Adhesive + Heat - resistant polyethylene foam +
insulation
material Adhesive tape
Indoor Vinyl tape
Outer
Floor exposed Water-proof hemp cloth + Bronze asphalt
covering
Outside Water-proof hemp cloth + Zinc plate + Oily paint
A Heat insulation material
B Pipe Note:
When using polyethylene cover as covering material, asphalt roof-
C Outer covering
(Wind the connection part and cutting part of
ing shall not be required.
heat insulation material with a finishing tape.)
• Do not insulate gas or low pressure pipe and liquid or high • Be sure to fully insulate connecting portion.
pressure pipe together.
B A
A Liquid pipe
A F B Gas pipe
Bad example
C Power lines
C D Finishing tape
E Insulating material
D F Transmission lines
E A These parts are not insulated.
C
Power lines Transmission lines
D
D
B A
Good example E
A Liquid pipe
Separation
B Gas pipe
C Power lines
D Insulating material
E Transmission lines
Penetrations
Inner wall (concealed) Outer wall Outer wall (exposed) Sleeve
D Heat insulating material
C E
A A B B Lagging
B
Caulking material
Band
I Waterproofing layer
Sleeve with edge
Penetrating portion on fire
Lagging material
Floor (fireproofing) Roof pipe shaft limit and boundary wall
Mortar or other incombustible caulking
D I Incombustible heat insulation material
G J
F
D When filling a gap with mortar, cover the
B
penetration part with steel plate so that
H the insulation material will not be caved in.
G A For this part, use incombustible materials
B for both insulation and covering.(Vinyl
1m 1m
covering should not be used.)
35 Installation
8. Y Branch and Header Branch Pipe type
8.1 Y branch pipe
[unit:mm]
Models Gas pipe Liquid pipe
I.D12.7 I.D12.7
I.D15.88 I.D15.88 I.D.6.35 I.D9.52 I.D6.35
I.D9.52
1
I.D15.88 74
ARBLN01621 I.D12.7
I.D.6.35 74
I.D.9.52
281 281
292 292
I.D19.05 1 O.D9.52
O.D15.88
70 I.D12.7 70
70 80 110
I.D19.05 I.D19.05
I.D28.58 I.D22.2 I.D15.88 I.D12.7 I.D15.88 I.D15.88 I.D12.7
2 2
1
I.D12.7
I.D15.88 I.D19.05 I.D15.88 I.D19.05 83
I.D31.8 96
I.D19.05 I.D12.7
ARBLN07121
376 371 3
3
404 394
I.D28.58 I.D31.8 I.D34.9 O.D31.8 O.D19.05 I.D22.2 O.D12.7 I.D9.52 I.D6.35 O.D12.7 I.D9.52
I.D28.58
2 1 3 3 2
O.D22.2
120 90 120 110 70
I.D34.9
I.D41.3 I.D38.1 I.D28.58 I.D19.05
2 I.D15.88 I.D19.05 I.D22.2 I.D15.88
I.D34.9 2
1
I.D38.1 I.D28.58 I.D15.88
125 I.D22.2 I.D19.05 I.D12.7
I.D34.9 I.D22.2 96
471
ARBLN14521 3
416 3
517
444
I.D19.05 I.D15.88 O.D38.1 I.D41.3 O.D34.9 I.D38.1
3
2 3 I.D41.3
O.D22.2 I.D12.7 O.D19.05 I.D9.52
120 130 O.D15.88 I.D9.52 I.D22.2 O.D12.7 I.D6.35
90
I.D12.7 O.D28.58 I.D22.2 2 3 3
3
2 I.D19.05
O.D15.88 110 80 110
Installation 36
8.2 Header
[unit:mm]
ID9.52 150
ID15.88
ARBL054 ID15.88 120
150 ID9.52 120
120
ID19.05 ID12.7
500 500
ID19.05 ID12.7
320
320
60*3=180 75 60*3=180 75
ID15.88 ID25.4
ID12.7 OD28.58 ID22.2 ID6.35
4 branch ID6.35 ID9.52 OD12.7
ID19.05 ID9.52
150 150
ARBL104 ID15.88 120 120 ID9.52 120
80
ID28.58 ID12.7
500 500
60*6=360 75 ID15.88 60*6=360 75 ID6.35
ID12.7 ID6.35
150
7 branch ID15.88
ID19.05
120
150
ID9.52
ID9.52
120
120 80
680 680
120 80
700
60*9=540 127 700
ID15.88
60*9=540 127
10 branch ID12.7
ID6.35
ID19.05 150 ID6.35
ID15.88 120
ARBL2010 ID9.52 120
150
120
37 Installation
9. Electrical Wiring
9.1 Areas of Caution
1. Follow ordinance of your governmental organization for technical standard related to electrical equipment,
wiring regulations and guidance of each electric power company.
WARNING
Be sure to have authorized Electrical engineers do electric work using special circuits in accordance
with regulations and this installation manual. If power supply circuit has a lack of capacity or electric
work deficiency, it may cause an electric shock or fire.
2. Install the outside unit transmission line away from the power source wiring so that it may not affected by
electric noise from the power source. (Do not run it through the same conduit.)
3. Be sure to provide designated grounding work to outside unit.
CAUTION
Be sure to correct the outside unit to earth. Do not connect earth line to any gas pipe, water pipe,
lightening rod or telephone earth line. If earth is incomplete, it may cause an electric shock.
4. Give some allowance to wiring for electrical part box of indoor and outside units, because the box is some-
times removed at the time of service work.
5. Never connect the main power source to terminal block of transmission line. If connected, electrical parts will
be burnt out.
6. Use 2-core shield cable for transmission line.(O mark in the figure below) If transmission lines of different
systems are wired with the same multiplecore cable, the resultant poor transmission and receiving will cause
erroneous operations. ( mark in the figure below)
7. Only the transmission line specified should be connected to the terminal block for outside unit transmission.
Outside Unit
WARNING
• Use the 2-core shield cables for transmission lines. Never use them together with power cables.
• The conductive shielding layer of cable should be grounded to the metal part of both units.
• Never use multi-core cable
• As this unit is equipped with an inverter, to install a phase leading capacitor not only will deteriorate
power factor improvement effect, but also may cause capacitor abnormal heating. Therefore, never
install a phase leading capacitor.
• Keep power imbalance within 2% of the supply rating. Large imbalance will shorten the life of the
smoothing capacitor.
• Introducing with a missing N-phase or with a mistaken N-phase will break the equipment.
Installation 38
9.2 Control Box and Wiring Location
- Unscrew all the screw, pull out the panel.
- Connect the transmission wire between outside unit and indoor unit,
the connection between outside unit and central controller system
pass through the sub PCB for central control.
- When connecting indoor unit with the shield cable, ground at the
grounding screw. Front Panel
When connecting central controller with the shield cable, ground at
the grounding screw.
- Refer to next page about the distance between main power cable
and communication cable.
- Refer to 106 page about Auto-Addressing and Test Run.
39 Installation
9.3 Transmission and Power Lines
1) Transmission cable
• Types : shielding wire CVVS or CPEVS
• Use wires of size : 1.0 ~ 1.5 mm2
• Insulation material : PVC
• Maximum allowable temperature: 60°C
• Maximum allowable line length: under 300m
2) Remote control cable
• Types : 3-core cable
3) Simple central control cable
• Types : 4-core cable (Shielding wire)
• Use wires of size : 1.0 ~ 1.5 mm2
• Insulation material : PVC
4) Separation of transmission and power lines
• If transmission and power lines are run alongside each other then here is a strong likelihood of operational
faults developing due to interference in the signal wiring caused by electrostatic and electromagnetic cou-
pling.
Note:
1. The figures are based on assumed length of parallel cabling up to 100m. For length in excess of 100m the
figures will have to be recalculated in direct proportion to the additional length of line involved.
2. If the power supply waveform continues to exhibit some distortion the recommended spacing in the table
should be increased.
• If the lines are laid inside conduits then the following point must also be taken into account when grouping
various lines together for introduction into the conduits.
• Power lines(including power supply to air conditioner) and signal lines must not be laid inside the same
conduit.
• In the same way, when grouping the power lines and signal lines should not be bunched together.
CAUTION
■ If apparatus is not properly earthed then there is always a risk of electric shocks, the earthing of the
apparatus must be carried out by a qualified person.
■ Use a power wire pipe for the power wiring.
Installation 40
◆ Example for mistake of wiring
• Do not separately connect the power of the indoor unit.
3phase 4lines power cable
Transmission cable(3lines): wired remote controller
Single phase 60Hz 220V
Transmission cable(2lines Shield cable) : Indoor~ Outside unit
3 phase 4 wires
power supply Breaker
60Hz 460V
CAUTION
Never install individual switch or individual outlet to cut the power connecting the indoor unit.
41 Installation
9.4 Dip switch setting
9.4.1 Location of setting switch
SW01B SW02B
7 segment
SW01B SW02B
ON ON
1 2 3 4 5 6 7 1 2 3 4 5 6 7
CAUTION
If the applicable dip switch is not set correctly,
the product may not operate properly.
■ Model code
Installation 42
■ Master Outside Setting
SW01B Setting SW02B Setting Remark
ON ON
Normal mode at shipping
factory
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
Normal mode at shipping
factory
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
Slave1 outside setting
(at the 2units)
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
Slave2 outside setting
ON ON
Standard mode at shipping
Standard
factory
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
ON ON
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 Installation
Function SW01B Setting SW02B Setting Remark
ON ON
longest Pipe
Length
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
After the system turn on,
Water temp Dip Switch 7,12 are
checking completed is indicated on
1 2 3 4 5 6 7 1 2 3 4 5 6 7 7-Segment
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
ON ON
Vacuum Mode
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
ON ON
Water Pipe
For water pipe Solenoid
Solenoid Valve
Valve 220V power
220V Functions
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14
CAUTION
■ After operating the dip switch to set the additional function, you must reset the power of the main PCB to
reflect the changed function. (After recovering the dip switch to cancel the additional function, you must
reset the power of the main PCB to reflect the change.)
■ If the dip switch is not set accurately, it can have excessive load on the product operation.
Set the dip switch properly.
Installation 44
9.5 Indoor unit auto addressing
• The address of the indoor units would be set by auto addressing.
1) Wait for 3 minutes after applying power supply (master and slave outside unit, indoor unit)
2) Press the switch of the outside unit (SW02V) for 5 seconds.
3) A "88" is indicated on 7-segment LED of the outside unit PCB.
4) For completing addressing, 2~7 minutes are required depending on numbers of indoor unit connection set.
5) Numbers of indoor unit connection set whose addressing is completed are indicated for 30 seconds on 7-segment LED
of the outside unit PCB.
6) After completing addressing, address of each indoor unit is indicated on the wired remote controller display window.
(CH01, CH02, CH03, .... CH06 : Indicated as number of indoor unit connection set.)
WARNING
• When replacing the indoor unit PCB, you must execute the auto addressing again. Always execute
this with all the power of indoor units and outside units connected. If the power is not connected to the
indoor unit, it can generate an operation error.
• When power is connected to the Multi V Water II for the first time, it will standby for more than 3 min-
utes to improve the indoor unit communication, and then the address must be set.
45 Installation
◆ The Procedure of Automatic Addressing
Power On
Waiting 3 minutes
YES
Indoor address number is displayed on wired remote control or
indoor unit display window. It is not an error message, will
OK disappeared when on/off button is pressed on remote control
ex) Display of 01, 02, ..., 15 means connection of 15 indoor
units and auto addressing is completed normally.
Installation 46
10. Test Run
Equipment design Design the system including cooling tower, boiler, pump etc.
- Check the equipment capacity (Water volume, temperature control range).
Water supply pipe and product Connect the water pipe to the inlet/outlet of the product so that the water
connection can be supplied to the product.
Water supply system test run Execute water supply system test run
- The product does not operate but the pump and water supply equipment
will operate to flow the Heat source water to the heat exchanger on the
product side.
- Flow the water to all water piping system to clean any alien particles inside
the pipes and execute an air purge to remove an air within the pipes to
make the water supply smoother.
- Clean all the strainers of water pipe including around outside units.
Judging whether there is any
Execute the test of water supply system without operating the product.
problem with the water supply
- Check whether outside unit inlet/outlet flow rate complies to the product
specification.
Standard Water volume is 96LPM based on 10HP and 196LPM based on
20HP.
- Check the water supply temperature. whether is OK
Execute the product test run After checking the normal condition of the water supply, execute the test run
of the product.
To prevent the freezing of the heat exchanger when the refrigerant is dis-
charged with the water supply blocked, discharge the refrigerant after
draining out around the outside unit.
47 Installation
10.2 Precaution before test run
1 Check whether the air is completely removed and the water supply is flowing smoothly.
Check whether there is any refrigerant leakage of any disconnected or loose communication or power wire, or use
2 the electric wiring diagram to check the wiring connection condition.
Check whether the power and communication wire are connected.
Precaution when blocking the water cooling type Multi V main power
- While using the product (Air conditioning season/Heating season), always connect the main power of the outside
unit.
- During the test run operation after installing the product or during the operation after blocking the outside unit
5 main power (Power outage etc.), you must always connect the power 6 hours prior to heating the crank case
heater. If the crank case is not preheated for more than 6 hours with the electric heater, it can cause a burn on
the compressor.
(Heating the bottom part of the compressor with the crank case heater is to evaporate the refrigerant included in
the oil inside the compressor.)
WARNING
• Always check whether the water supply is flowing smoothly before the test run. (If sufficient amount
of water is not flowing, it can burn the product.)
• During the initial test run after installing the product, leaving the product for more than 3 days or
after replacing the compressor, power must be connected 6 hours prior to the operation to heat the
compressor heater. (If the product is not heated sufficiently, it can burn the product.)
Installation 48
10.3 How to Cope with Abnormal Test Run
The phenomena from main component failure
❈ When CH24 or CH180 error occurs during the test operation of the heater, the inside of the panel heat exchanger may be
partially frozen and therefore, be sure to get rid of its cause and then, re-operate the device.
(The root cause of partial freezing: The lack of flow of heat-sourced water, suspension of water, lack of cooling medium,
infiltration of foreign substance inside of panel heat exchanger )
49 Installation
10.4 Maintenance of plate type heat exchanger
As the scales are created in the panel heat exchanger, its efficiency may decrease or damage may occur due to winter-sowing
due to the decrease in its flow.
Due to this reason, regular maintenance is necessary so that the scales shouldn't be created.
1. Before the season of use, check below points.(Once a year)
1) inspection on water quality to check if this is within the standard condition.
2) Clean the strainer.
3) Check if the flow is appropriate.
4) Check if the operation environment is appropriate.(Pressure, flow, output temperature)
2. Below procedure should be abided by in order to clean the panel heat exchanger. (Once every 5 years)
1) Check if the service port is equipped with the water pipe in order to clean the chemical solution.
5% diluted formic acid, citric acid, oxalic acid, acetate acid, phosphoric acid and etc. are appropriate for the chemical solu-
tion for wiping out the scales.(Hydrochloric acid, sulphuric acid, nitric acid and etc. shouldn't be used due to its corrosion.)
2) Be sure to check if the gate valve of inflow/outflow pipe and the valve for outflow pipe are properly closed when cleaning.
3) Connect the water pipe for cleaning with the chemical solvent through the service plug of the pipe and fill up the panel
heat exchanger with 50°C~60°C of cleaning solvent and circulate it with the pump for 2~5 hours. The circulation time
may depend on the temperature of the cleaning solvent or the creation of the scales. Therefore, observe change in the
color of the chemical solvent to set the circulation time for removing the scales.
4) After the circulation of the solvent, extract the solvent inside of the panel heat exchanger and fill up 1~2% of NaOH or
NaHCO3 and then, circulate it for 15~20 minutes to neutralize the heat exchanger.
5) Once the neutralization is completed, clean the inside of the panel heat exchanger with clean water.
Measure the water pH to check if the chemical solvent is properly removed or not.
6) When using a different kind of chemical solvent in the market, be sure to check if there is any corrosive action to stainless
or copper in advance or not.
7) For details on the cleaning chemical solvent, be sure to consult the specialists of the related corporation.
3. After cleaning, operate the device to see if it works properly once again.
Service plug
Screening net
Water-cooling
type multi V
Strainer
Installation 50
10.5 Daily check/management
1. Water quality control
The plate type heat exchanger is not structured to be disassembled, cleaned or replaced with parts.
To prevent corrosion or scaling on the plate type heat exchanger, special care must be taken to control the water quality.
Water quality must satisfy the minimum criteria of the reference water quality items.
When anti-corrosion agent or corrosion inhibitor is added, the substance must not have any corrosive effect on stainless
steel and copper.
Even if the circulating water is not contaminated by the external air, it is recommended to empty the water flowing in the
pipe and to resupply the water.
2. Flow rate control
If the flow rate is insufficient, it can cause freezing on the plate type heat exchanger.
Check whether the strainer is clogged or whether the pipe is filled with air and then check the temperature and pressure
difference of the inlet and outlet pipe to check whether the flow rate is insufficient.
If the temperature and pressure difference is above the appropriate level, it means that the flow rate is reduced. In this
case, the operation must immediately be stopped and re-operated when the root cause is resolved. (*If air is trapped in
the pipe, the air must be purged. Air inside the water pipe interferes with the circulation of the heat water supply and can
cause insufficient flow rate or freezing.)
3. Brine density management
When using the brine (Anti-freeze) in the heat water supply, designated type and density must be used. Calcium chloride
brine can cause corrosion on the plate type heat exchanger and must not be used.
If the anti-freeze liquid is left as is, it absorbs the moisture from the air to cause a drop in the density, leading to freezing
of plate type heat exchanger. Therefore minimize the contact surface with the atmosphere and periodically measure the
density of the brine to supplement the brine as needed to maintain the density.
CAUTION
• The above checklist is set based on the minimum period and more frequent checking can be required depending on the
operating condition/water quality condition.
• When cleaning the heat exchanger, make sure to take parts out or lock the value so that chemical detergent does not
penetrate into the pressure gauge etc.
• When cleaning the heat exchanger, check the connecting part of the water pipes prior to cleaning so that the chemical
detergent does not leak.
• After sufficiently mixing the chemical detergent with water, start cleaning.
• Cleaning the heat exchanger is easier at the initial stage and becomes difficult after the scaling has accumulated.
• In areas where the water quality is poor, cleaning is required periodically.
Because chemical detergent has strong acidity, it must be washed off thoroughly with water.
• To check whether it is cleaned well inside, remove the hose and check the inside.
• Purge the air to remove any air inside the water pipe.
• After checking, always check whether the heat water supply is flowing normally flowing before operating the product.
51 Installation
10.7 Self-Diagnosis Function
Error Indicator
• This function indicates type of failure in self-diagnosis and occurrence of failure for air condition.
• Error mark is displayed on display window of indoor units and wired remote controller, and 7-segment LED of outside unit
control board as shown in the table.
• If more than two troubles occur simultaneously, low number of error code is first displayed.
• After error occurrence, if error is released, error LED is also released simultaneously.
Communication error between outside unit and When the indoor unit does not receive the outside communication signal con-
0 5 -
indoor unit tinuously for 5 minutes or more
0 6 - Indoor unit pipe outlet temperature sensor error Indoor unit pipe outlet temperature sensor disconnection or short circuit
0 7 - Different mode operation When operated in different operating mode than the one first operated
Indoor unit EEPROM error Communication error between MICOM and EEPROM or when there is
0 9 -
no indoor unit EEPROM data
1 0 - Indoor unit BLDC motor feedback signal error When motor connector is removed or defective
1 Master outside unit inverter compressor IPM fault Master outside unit inverter compressor drive IPM error
2 1 2 Slave1 outside unit inverter compressor IPM fault Slave1 outside unit inverter compressor drive IPM error
3 Slave2 outside unit inverter compressor IPM fault Slave2 outside unit inverter compressor drive IPM error
Master outside unit inverter compressor DC link DC voltage is not charged after master outside unit operating relay is turned
1
under-voltage on
DC voltage is not charged after slave1 outside unit operating relay is turned on
2 3 2 Slave1 outside unit inverter compressor DC link
under-voltage
Slave2 outside unit inverter compressor DC link DC voltage is not charged after slave2 outside unit operating relay is turned on
3
under-voltage
Outside unit
Master outside unit high pressure switch Compressor maintenance by master outside unit high pressure switch
1
Flow rate insufficiency or flow switch trouble of master outside unit
Slave1 outside unit high pressure switch Compressor maintenance by slave1 outside unit high pressure switch
2 4 2
Flow rate insufficiency or flow switch trouble of slave1 outside unit
Slave2 outside unit high pressure switch Compressor maintenance by slave2 outside unit high pressure switch
3
Flow rate insufficiency or flow switch trouble of slave2 outside unit
Master outside unit input voltage over-voltage Master outside unit input voltage is 487V and above or less than 270V
1
/under-voltage
Slave1 outside unit input voltage over-voltage Slave1 outside unit input voltage is 487V and above or less than 270V
2 5 2
/under-voltage
Slave2 outside unit input voltage over-voltage Slave2 outside unit input voltage is 487V and above or less than 270V
3
/under-voltage
Installation 52
Display Error item Root cause of error
number
Master outside unit inverter compressor operation Initial operation failure due to master outside unit inverter compressor error
1
failure error
Slave1 outside unit inverter compressor operation Initial operation failure due to Slave1 outside unit inverter compressor error
2 6 2
failure error
Slave2 outside unit inverter compressor operation Initial operation failure due to Slave2 outside unit inverter compressor error
3
failure error
Master outside unit inverter DC link over-voltage
Compressor turned off due to master outside unit inverter DC voltage over-
1
error charge
Slave1 outside unit inverter DC link over-voltage
Compressor turned off due to slave1 outside unit inverter DC voltage over-
2 8 2
error charge
Slave2 outside unit inverter DC link over-voltage
Compressor turned off due to slave2 outside unit inverter DC voltage over-
3
error charge
Master outside unit inverter compressor over-cur-
Master outside unit inverter compressor error or operating component (IPM)
1
rent error operation
Slave1 outside unit inverter compressor over-cur-
Slave1 outside unit inverter compressor error or operating component (IPM)
2 9 2
rent error operation
Slave2 outside unit inverter compressor over-cur-
Slave2 outside unit inverter compressor error or operating component (IPM)
3
rent error operation
1 Master outside unit inverter CT under-current error
Compressor turned off due to master outside unit inverter CT under-Current
3 1 2 Slave1 outside unit inverter CT under-current error
Compressor turned off due to Slave1 outside unit inverter CT under-Current
3 Slave2 outside unit inverter CT under-current error
Compressor turned off due to Slave2 outside unit inverter CT under-Current
Outside unit
53 Installation
Display Error item Root cause of error
number
Master outside unit inverter compressor CT sen- Master outside unit inverter compressor current detection (CT) sensor discon-
1
sor error nection or short circuit
Slave1 outside unit inverter compressor CT sen- Slave1 outside unit inverter compressor current detection (CT) sensor discon-
4 0 2
sor error nection or short circuit
Slave2 outside unit inverter compressor CT sen- Slave2 outside unit inverter compressor current detection (CT) sensor discon-
3
sor error nection or short circuit
Master outside unit inverter compressor discharge Master outside unit inverter compressor discharge temperature sensor discon-
1
temperature sensor error nection or short circuit
Slave1 outside unit inverter compressor discharge Slave1 outside unit inverter compressor discharge temperature sensor discon-
4 1 2
temperature sensor error nection or short circuit
Slave2 outside unit inverter compressor discharge Slave2 outside unit inverter compressor discharge temperature sensor discon-
3
temperature sensor error nection or short circuit
1 Master outside unit under-voltage sensor error Master outside unit under-vlotage sensor disconnection or short circuit
4 2 2 Slave1 outside unit under-voltage sensor error Slave1 outside unit under-vlotage sensor disconnection or short circuit
3 Slave2 outside unit under-voltage sensor error Slave2 outside unit under-vlotage sensor disconnection or short circuit
1 Master outside unit over-voltage sensor error Master outside unit over-vlotage sensor disconnection or short circuit
4 3 2 Slave1 outside unit over-voltage sensor error Slave1 outside unit over-vlotage sensor disconnection or short circuit
3 Slave2 outside unit over-voltage sensor error Slave2 outside unit over-vlotage sensor disconnection or short circuit
1 Master outside unit air temperature sensor error Master outside unit air temperature sensor disconnection or short circuit
4 4 2 Slave1 outside unit air temperature sensor error Slave1 outside unit air temperature sensor disconnection or short circuit
3 Slave2 outside unit air temperature sensor error Slave2 outside unit air temperature sensor disconnection or short circuit
Outside unit
Master Outdoor Unit Heat Exchanger Master Outdoor Unit Heat Exchanger Temperature Sensor(A) Open or Short
1
Temperature Sensor(A) Fault
Slave1 Outdoor Unit Heat Exchanger Slave1 Outdoor Unit Heat Exchanger Temperature Sensor(A) Open or Short
4 5 2
Temperature Sensor(A) Fault
Slave2 Outdoor Unit Heat Exchanger Slave2 Outdoor Unit Heat Exchanger Temperature Sensor(A) Open or Short
3
Temperature Sensor(A) Fault
Master outside unit suction temperature sensor Master outside unit suction temperature sensor disconnection or short circuit
1
error
Slave1 outside unit suction temperature sensor Slave1 outside unit suction temperature sensor disconnection or short circuit
4 6 2
error
Slave2 outside unit suction temperature sensor Slave2 outside unit suction temperature sensor disconnection or short circuit
3
error
Master outside unit static speed compressor Master outside unit static speed compressor discharge temperature sensor
1
discharge temperature sensor error disconnection or short circuit
Slave1 outside unit static speed compressor Slave1 outside unit static speed compressor discharge temperature sensor
4 7 2
discharge temperature sensor error disconnection or short circuit
Slave2 outside unit static speed compressor Slave2 outside unit static speed compressor discharge temperature sensor
3
discharge temperature sensor error disconnection or short circuit
Master Outdoor Unit Heat Exchanger Master Outdoor Unit Heat Exchanger Temperature Sensor(B) Open or Short
1
Temperature Sensor(B) Fault
Slave1 Outdoor Unit Heat Exchanger Slave1 Outdoor Unit Heat Exchanger Temperature Sensor(B) Open or Short
4 8 2
Temperature Sensor(B) Fault
Slave2 Outdoor Unit Heat Exchanger Slave2 Outdoor Unit Heat Exchanger Temperature Sensor(B) Open or Short
3
Temperature Sensor(B) Fault
Installation 54
Display Error item Root cause of error
number
1 Master outside unit 3 phase power missing Master oudoor unit power line phase missing
5 0 2 Slave1 outside unit 3 phase power missing Slave1 oudoor unit power line phase missing
3 Slave2 outside unit 3 phase power missing Slave2 oudoor unit power line phase missing
Over-capacity Excessive connection f indoor unit connection display value
5 1 -
(Indoor unit capacity sum is excessive) connection (Different from outside unit)
Communication error with master outside unit When the inverter controller signal is not received from the master outside unit
1
inverter contrller inverter controller
Communication error with Slave1 outside unit When the inverter controller signal is not received from the slave1 outside unit
5 2 2
inverter contrller inverter controller
Communication error with slave2 outside unit When the inverter controller signal is not received from the slave2 outside unit
3
inverter contrller inverter controller
Communication error with master outside unit con- When the indoor uint control signal is not received from the master outside unit
5 3 -
trller and indoor unit inverter controller
1 Master outside unit 3 phase power reverse phase Master outside unit 3 phase power reverse phase connection
5 4 2 Slave1 outside unit 3 phase power reverse phase Slave1 outside unit 3 phase power reverse phase connection
3 Slave2 outside unit 3 phase power reverse phase Slave2 outside unit 3 phase power reverse phase connection
1 Master outside unit inverter PCB EEPROM error Master oudoor unit inverter PCB EEPROM ACCESS error
6 0 2 Slave1 outside unit inverter PCB EEPROM error Slave1 oudoor unit inverter PCB EEPROM ACCESS error
3 Slave2 outside unit inverter PCB EEPROM error Slave2 oudoor unit inverter PCB EEPROM ACCESS error
1 Master outside unit static speed CT sensor error Master outside unit static speed CT sensor disconnection or short circuit
7 0 2 Slave1 outside unit static speed CT sensor error Slave1 outside unit static speed CT sensor disconnection or short circuit
Outside unit
3 Slave2 outside unit static speed CT sensor error Slave2 outside unit static speed CT sensor disconnection or short circuit
Master outside unit inverter PCB input instant Master outside unit inverter PCB input instant over-current (Peak) exceeded
1
over-current (Peak)
Slave1 outside unit inverter PCB input instant Slave1 outside unit inverter PCB input instant over-current (Peak) exceeded
7 3 2
over-current (Peak)
Slave2 outside unit inverter PCB input instant Slave2 outside unit inverter PCB input instant over-current (Peak) exceeded
3
over-current (Peak)
Master outside unit inverter PCB phase imbalance When the master outside unit inverter PCB input current is different
1
Slave1 outside unit inverter PCB phase imbalance When the slave1 outside unit inverter PCB input current is different
7 4 2
Slave2 outside unit inverter PCB phase imbalance When the slave2 outside unit inverter PCB input current is different
3
Communication error between master outside unit master MICOM and EEP-
1 Master outside unit master PCB EEPROM error
ROM or EEPROM missing
Communication error between slave1 outside unit master MICOM and EEP-
8 6 2 Slave1 outside unit master PCB EEPROM error
ROM or EEPROM missing
Communication error between slave2 outside unit master MICOM and EEP-
3 Slave2 outside unit master PCB EEPROM error
ROM or EEPROM missing
Communication error between master outside unit When signal from slave outside unit is not received from master outside unit
1
and outside unit master MICOM
Communication error between slave1 outside unit When signal from slave outside unit is not received from slave1 outside unit
1 0 4 2
and outside unit master MICOM
Communication error between slave2 outside unit When signal from slave outside unit is not received from slave2 outside unit
3
and outside unit master MICOM
55 Installation
Display Error item Root cause of error
number
Master outside unit liquid pipe temperature sensor Master outside unit liquid pipe temperature sensor disconnection or short cir-
1
error cuit
Slave1 outside unit liquid pipe temperature sensor Slave1 outside unit liquid pipe temperature sensor disconnection or short cir-
1 1 3 2
error cuit
Slave2 outside unit liquid pipe temperature sensor Slave2 outside unit liquid pipe temperature sensor disconnection or short cir-
3
error cuit
Master outside unit over-cooling inlet temperature Master outside unit over-cooling inlet temperature sensor disconnection or
1 sensor error short circuit
Slave1 outside unit over-cooling inlet temperature Slave1 outside unit over-cooling inlet temperature sensor disconnection or
1 1 4 2
sensor error short circuit
Slave2 outside unit over-cooling inlet temperatur Slave2 outside unit over-cooling inlet temperature sensor disconnection or
3
Outside unit
■ Refer to the troubleshooting guide of service technical manual for each error.
Installation 56
11. Cooling tower applied method
Open type
cooling tower Closed type
cooling tower
1st side 2nd side
Heat exchange
[Open type cooling tower + Middle heat exchanger] [Closed type cooling tower]
Heat exchanger is installed between the cooling Heat source water of the cooling tower is supplied
tower and outside unit system piping, and the tem- directly to the outside unit system.
perature difference between 1st side and 2nd side
is maintained constantly
CAUTION
When the open type cooling tower is used and the water supply is directly connected to the 2nd heat exchanger, product
damage by alien particle cannot be repaired for free.
- Always use the 2nd heat exchanger.
57 Installation
12. Water Solenoid Valve Control
12.1 Central Control (Use DDC Port)
4(N) Water
ODU
ODU DDC Water In
3(L) Out
Relay
PCB 2(N)
CN_24 (to DDC) 1(L)
Solenoid
Relay Valve
BMS
PI485
Set the dip switch refer to Fig.1 and turn on the power when you individual control for
water solenoid valve control.
SW01B SW02B
ON ON
1 2 3 4 5 6 7 1 2 3 4 5 6 7
Fig.1
Installation 58
Special Guide
Special Guide
1. Caution For Refrigerant Leak
The installer and system specialist shall secure safety against leakage according to local regulations or standards.
The following standards may be applicable if local regulations are not available.
1.1 Introduction
Though the R410A refrigerant is harmless and incombustible itself , the room to equip the air conditioner should be large to
such an extent that the refrigerant gas will not exceed the limiting concentration even if the refrigerant gas leaks in the room.
■ Limiting concentration
Limiting concentration is the limit of Freon gas concentration where immediate measures can be taken with-
out hurting human body when refrigerant leaks in the air. The limiting concentration shall be described in the
unit of kg/m3 (Freon gas weight per unit air volume) for facilitating calculation.
Limiting concentration: 0.44kg/m3(R410A)
Outside unit
Flow of
(No.1 system) refrigerant
Special Guide 1
(3) With partition and without opening which serve as passage of air to adjoining room
Outside unit
Indoor unit
Smallest
room
Indoor unit
Pay a special attention to the place, such as a basement, etc. where refrigerant can stay, since refrigerant is
heavier than air.
2 Special Guide
P/No.: MFL61741603
Air Conditioner
20 Yeouido-dong, Yeongdeungpo-gu,
Yeouido P.O.Box 335 Seoul,
150-721, Korea.
http://www.lgeaircon.com