https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by sales@ChinaStandards.

net

ICS 83.120

Q 23

NATIONAL STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
中华人民共和国国家标准
GB/T 7190.2-2008

Supersedes GB/T 7190.2-1997

Glass Fiber Reinforced Plastic Cooling

Tower - Part 2: Large Glass Fiber
Reinforced Plastic Cooling Tower

玻璃纤维增强塑料冷却塔
第 2 部分：大型玻璃纤维增强塑料冷却塔

Issued on: June 30, 2008 Implemented on: April 1, 2009

Jointly Issued by the General Administration of Quality Supervision,

Inspection and Quarantine of the People's Republic of China
and the Standardization Administration of the People's
Republic of China

https://www.chinastandards.net/standard/GBT7190.2-2008.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Contents

Foreword .................................................................................................................................... I
1 Scope ................................................................................................................................... 1
2 Normative References ......................................................................................................... 1
3 Terminologies and Definitions ............................................................................................ 1
4 Product Classification.......................................................................................................... 3
5 Technical Requirements ...................................................................................................... 4
6 Test Methods ....................................................................................................................... 5
7 Inspection Rules .................................................................................................................. 6
8 Marking, Packaging, Transportation and Storage, and Sample or Product Instructions ..... 8
9 Others .................................................................................................................................. 9
Appendix A (Normative) Test Methods for Thermal Performance of Cooling Tower ......... 12
Appendix B (Normative) Test Method for Noise of Cooling Tower .................................... 21
Appendix C (Normative) Test Method for Consumptive Electric Power Ratio ................... 22
Appendix D (Normative) Test Method for Drifting Ratio.................................................... 23
Appendix E (Normative) Test Methods for Heat Resistance in Water and Load-Bearing
Property of the Flat Sheet and Assembled Block of Plastic Fill .............................................. 25
Appendix F (Informative) Calculation Examples of Thermal Performance ........................ 27

https://www.chinastandards.net/standard/GBT7190.2-2008.html
https://www.ChinaStandards.net -> Buy the full version pdf -> Delivered by [email protected]

Glass Fiber Reinforced Plastic Cooling Tower -

Part 2: Large Glass Fiber Reinforced Plastic Cooling Tower
玻璃纤维增强塑料冷却塔
第 2 部分：大型玻璃纤维增强塑料冷却塔

1 Scope

This part of GB/T 7190 specifies the product classification, technical requirements, test
methods, inspection rules, marking, packaging, transportation and storage, and others of large
cooling tower.
This part is applicable to the mechanical draft industrial type cooling tower with cooling
water flow no less than 1,000m3/h.

2 Normative References

The following standards contain provisions which, through reference in this part of GB/T
7190, constitute provisions of this part. For dated reference, subsequent amendments to
(excluding corrections to), or revisions of, any of these publications do not apply. However,
the parties to agreements based on this part are encouraged to investigate the possibility of
applying the most recent editions of the standards. For undated references, the latest edition of
the normative document referred to applies.
GB/T 1033 Test Method for Density and Relative Density of Plastics
GB/T 1040 Plastics - Determination of Tensile Properties
GB/T 1449 Fibre-reinforced Plastic Composites - Determination of Flexural
Properties
GB/T 2406 Plastics - Determination of Flammability by Oxygen Index
GB/T 2577 Test Method for Resin Content of Glass Fiber Reinforced Plastics
GB/T 3854 Test Method for Hardness of Reinforced Plastics by Means of Barcol
Impresser
GB/T 8924 Test Method for Flammability Characteristics of Fiber Reinforced
Plastics - Oxygen Index Method
GB/T 13041 Packaging Containers - Magnesium Oxychloride Concrete Case
GB 50204 Code for Acceptance of Constructional Quality of Concrete Structures
GB 50205 Code for Acceptance of Construction Quality of Steel Structures

3 Terminologies and Definitions

https://www.chinastandards.net/standard/GBT7190.2-2008.html