Wind Turbine Blade Design
Joseph Rand The Kidwind Project [email protected] 877-917-0079
Calculation of Wind Power
Power the=wind Power in thein Wind AV3
Effect of swept area, A Effect of wind speed, V Effect of air density,
Swept Area: A = R2 Area of the circle swept by the rotor (m2).
Many Different Rotors
KidWind Project | www.kidwind.org
Number of Blades One
Rotor must move more rapidly to capture same amount of wind
Gearbox ratio reduced Added weight of counterbalance negates some benefits of lighter design Higher speed means more noise, visual, and wildlife impacts
Blades easier to install because entire rotor can be assembled on ground Captures 10% less energy than two blade design Ultimately provide no cost savings
Number of Blades - Two
Advantages & disadvantages similar to one blade Need teetering hub and or shock absorbers because of gyroscopic imbalances Capture 5% less energy than three blade designs
Number of Blades - Three
Balance of gyroscopic forces Slower rotation
increases gearbox & transmission costs More aesthetic, less noise, fewer bird strikes
Blade Composition Wood
Wood
Strong, light weight, cheap, abundant, flexible Popular on do-it yourself turbines
Solid plank Laminates Veneers Composites
Blade Composition Metal
Steel
Heavy & expensive
Aluminum
Lighter-weight and easy to work with Expensive Subject to metal fatigue
Blade Construction Fiberglass
Lightweight, strong, inexpensive, good fatigue characteristics Variety of manufacturing processes
Cloth over frame Pultrusion Filament winding to produce spars
Most modern large turbines use fiberglass
KidWind Project | www.kidwind.org
KidWind Project | www.kidwind.org
Lift & Drag Forces
The Lift Force is perpendicular to the direction of motion. We want to make this force BIG.
= low
= medium <10 degrees
The Drag Force is parallel to the direction of motion. We want to make this force small.
= High Stall!!
Airfoil Shape
Just like the wings of an airplane, wind turbine blades use the airfoil shape to create lift and maximize efficiency.
The Bernoulli Effect
Lift/Drag Forces Experienced by Turbine Blades
KidWind Project | www.kidwind.org
Twist & Taper
Speed through the air of a point on the blade changes with distance from hub Therefore, tip speed ratio varies as well To optimize angle of attack all along blade, it must twist from root to tip
Fastest Faster Fast
Tip-Speed Ratio
Tip-speed ratio is the ratio of the speed of the rotating blade tip to the speed of the free stream wind. There is an optimum angle of attack which creates the highest lift to drag ratio. Because angle of attack is dependant on wind speed, there is an optimum tip-speed ratio
R
Where, = rotational speed in radians /sec
R TSR = V
R = Rotor Radius V = Wind Free Stream Velocity
Performance Over Range of Tip Speed Ratios
Power Coefficient Varies with Tip Speed Ratio Characterized by Cp vs Tip Speed Ratio Curve
Betz Limit
All wind power cannot be captured by rotor or air would be completely still behind rotor and not allow more wind to pass through. Theoretical limit of rotor efficiency is 59% Most modern wind turbines are in the 35 45% range
Rotor Solidity
Solidity is the ratio of total rotor planform area to total swept area
Low solidity (0.10) = high speed, low torque
R
a
A
High solidity (>0.80) = low speed, high torque
Solidity = 3a/A
Pitch Control Mechanisms
KidWind Project | www.kidwind.org
Some Wacky Ideas
Manufacturing Blades
The blade mold (left) is lined with layers of fiberglass, then injected with epoxy resin. To enhance stiffness, a layer of wood is placed between the fiberglass layers. The two molds are joined and adhered together using a special liquid epoxy, which evenly joins the two sides of the blade. Finally, the whole mold is baked like a cake! 8 hours at 70 degrees C.
Manufacturing Blades
Before delivery, samples of the rotor blades have to go through a variety of static and dynamic tests. First, they are subjected to 1.3 times the maximum operating load. To simulate 20 years of material fatigue, the blades are then mounted on special test beds and made to vibrate around two million times, before the endurance of the material is again tested with a final static test. The blades are painted white, then shipped to wind farms all over the world.
Advanced Classroom Blades
Airfoil Blades
Cardboard Tube for twisted blades
Wind Turbine Blade Challenge
Students perform experiments and design different wind turbine blades Use simple wind turbine models Test one variable while holding others constant Record performance with a multimeter or other load device Goals: Produce the most voltage, pump the most water, lift the most weight
Minimize Drag Maximize LIFT Harness the POWER of the wind!
Questions?
